Product Bulletin OP604ESA September 1996 High Reliability NPN Silicon Phototransistor Type OP604ESA-XN(3) Features Absolute Maximum Ratings (TA = 25o C unless otherwise noted) • Processed to Optek’s Space level Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 C to +150 C o o Operating Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . -55 C to +125 C Collector-Emitter Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 V Emitter-Collector Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0 V o (1) Soldering Temperature (for 5 seconds with soldering iron) . . . . . . . . . . . . . 240 C (2) Power Dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mW screening program patterned after FSA/SCC Generic Specification 5000 • Miniature hermetically sealed package • Ideal for direct mounting in PC boards • Mechanically and spectrally matched to the OP224 Series LED Description The OP604ESA consists of a high reliability NPN silicon phototransistor mounted in a miniature glass lensed, hermetically sealed, “pill”package. All devices are processed to Optek’s program patterned after ESA/SCC Generic Specification No. 5000. See page 13-4 for details. This device type is lensed and has an acceptance half angle of 18o measured from the optical axis to the half power point. The series is also mechanically and spectrally matched to Optek’s OP224 series high reliability infrared emitting diode. o o Notes: (1) No-clean or low solids RMA flux is recommended. Duration can be extended to 10 seconds maximum when wave soldering. (2) Derate linearly 0.5 mW/o C above 25o C. (3) “X”defines the testing level per ESA/SCC Generic Specification 5000, Chart III. “X”will be either “B”(full processing) or “C”(reduced processing). “N”defines lot acceptance testing. “N”will be either 1, 2, or 3. Level 3 is the lowest defined level with emphasis on electrical tests, solderability, and visual inspection. Level 2 requires all tests of Level 3 and adds indurance testing (burn-in) with drift limits on key parameters. Level 1 is the most stringent LAT level and includes all requirements of Levels 2 and 3 plus additional testing for tolerance of thermal, mechanical, and environmental exposure. Part Number Guide OP604ESA-XN Optek High Reliability ESA/SCC Specification No. 5000 “B”- Full Processing “C”- Reduced Processing Level ”1” Environmental/Mechanical plus 2 & 3 Level “2”Life Testing plus Level 3 Level “3" Electrical Inspection Optek Technology, Inc. 1215 W. Crosby Road Carrollton, Texas 75006 13-32 (972) 323-2200 Fax (972) 323-2396 Type OP604ESA-XN Electrical Characteristics (TA = 25o C unless otherwise noted) Symbol IC(ON) ICEO Parameter On-State Collector Current Min Typ Max 7.0 Collector Dark Current 25 100 Units Test Conditions mA VCE = 5.0 V, Ee = 20 mW/cm2(3)(4) nA µA VCE = 10.0 V, Ee = 0 VCE = 30.0 V, Ee = 0, TA = 100o C V(BR)CEO Collector-Emitter Breakdown Voltage 50 V IC = 100 µA, Ee = 0 V(BR)ECO Emitter-Collector Breakdown Voltage 7.0 V IE = 100 µA, Ee = 0 VCE(SAT) Collector-Emitter Saturation Voltage 0.40 V IC = 0.4 mA, Ee = 20 mW/cm2(3)(4) tr Rise Time 20.0 µs tf Fall Time 20.0 µs VCC = 30 V, IC = 1.00 mA, RL = 100 Ω Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible. Optek Technology, Inc. 1215 W. Crosby Road Carrollton, Texas 75006 (972) 323-2200 Fax (972) 323-2396 13-33