NLAS52231 Ultra-Low 0.4 W Dual SPDT Analog Switch with Overshoot The NLAS52231 is a dual SPDT analog switch with overshoot capability on the signal lines. It is ideally suited for audio applications that require very low RON values for maximum signal transfer. The overshoot feature included in the NLAS52231 allows analog signals on the COM, NO or NC lines to swing safely above VCC without incurring significant leakage. This feature provides added protection against undesirable leakage or damage to the device in the event that an incoming audio signal spikes above its nominal level. The NLAS52231 features a wide V CC operating range, 1.65 V-4.5 V. It is capable of interfacing with control input select line voltages, VIN, as low as 1.3 V for a VCC of 3.0 V. The NLAS52231 is offered in a very small 1.4mm x 1.8mm 10-pin UQFN package. http://onsemi.com MARKING DIAGRAM UQFN10 CASE 488AT 1 S2MG G S2 = Specific Device Code M = Date Code/Assembly Location G = Pb-Free Device (Note: Microdot may be in either location) Features •Ultra-Low RON: 0.4 at VCC = 4.2 V •Overshoot Capability: VIS can safely rise up to 1.1 V above VCC •VCC Range: 1.65 V to 4.5 V •1.4 x 1.8 x 0.55 mm UQFN10 •These are Pb-Free Devices Typical Applications •Mobile Phones •Portable Devices NC2 GND 7 6 IN2 8 5 NC1 COM2 9 4 IN1 10 3 COM1 NO2 NLAS52231 1 2 VCC NO1 AUDIO Source #1 Audio Terminal FUNCTION TABLE AUDIO Source #2 IN 1, 2 NO 1, 2 NC 1, 2 0 1 OFF ON ON OFF ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet. Figure 1. Applications Diagram © Semiconductor Components Industries, LLC, 2007 September, 2007 - Rev. 1 1 Publication Order Number: NLAS52231/D NLAS52231 PIN DESCRIPTION QFN PIN # Symbol Name and Function 2, 5, 7, 10 NC1 to NC2, NO1 to NO2 4, 8 IN1 and IN2 3, 9 COM1 and COM2 6 GND Ground (V) 1 VCC Positive Supply Voltage Independent Channels Controls Common Channels MAXIMUM RATINGS Symbol Parameter Value Unit -0.5 to +5.5 V -0.5 v VIS v VCC + 0.5 V -0.5 v VIN v +5.5 V VCC Positive DC Supply Voltage VIS Analog Input Voltage (VNO, VNC, or VCOM) VIN Digital Select Input Voltage Ianl1 Continuous DC Current from COM to NC/NO ±300 mA Ianl-pk1 Peak Current from COM to NC/NO, 10 Duty Cycle (Note 1) ±500 mA Iclmp Continuous DC Current into COM/NO/NC with Respect to VCC or GND ±100 mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Defined as 10% ON, 90% OFF Duty Cycle. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 4.5 V VCC DC Supply Voltage 1.65 VIN Digital Select Input Voltage Overshoot Tolerance GND 4.5 V VIS Analog Input Voltage (NC, NO, COM) GND VCC + 1.1 V TA Operating Temperature Range -40 +85 °C tr, tf Input Rise or Fall Time, SELECT 20 10 ns/V VCC = 1.6 V - 2.7 V VCC = 3.0 V - 4.5 V ESD PROTECTION Symbol Parameter Value Unit ESD Human Body Model (HBM) 3.0 kV ESD Machine Model (MM) 100 V http://onsemi.com 2 NLAS52231 NLAS52231 DC CHARACTERISTICS - DIGITAL SECTION (Voltages Referenced to GND) Guaranteed Limit Parameter Symbol Condition VCC 25°C -40°C to +85°C Unit VIH Minimum High-Level Input Voltage, Select Inputs 3.0 4.3 1.3 1.6 1.3 1.6 V VIL Maximum Low-Level Input Voltage, Select Inputs 3.0 4.3 0.5 0.6 0.5 0.6 V IIN Maximum Input Leakage Current, Select Inputs VIN = 4.5 V or GND 4.3 ±0.1 ±1.0 A IOFF Power Off Leakage Current VIN = 4.5 V or GND 0 ±0.5 ±2.0 A ICC Maximum Quiescent Supply Current (Note 2) Select and VIS = VCC or GND 1.65 to 4.5 ±1.0 ±2.0 A 2. Guaranteed by design. Resistance measurements do not include test circuit or package resistance. NLAS52231 DC ELECTRICAL CHARACTERISTICS - ANALOG SECTION Guaranteed Maximum Limit 25°C Max Unit RON (NC) NC “ON” Resistance (Note 3) VIN v VIL VIS = GND to VCC IINI v 100 mA 3.0 4.3 0.46 0.43 0.56 0.53 RON (NO) NO “ON” Resistance (Note 3) VIN w VIH VIS = GND to VCC IINI v 100 mA 3.0 4.3 0.38 0.35 0.48 0.43 RFLAT (NC) NC_On-Resistance Flatness (Notes 3, 4) ICOM = 100 mA VIS = 0 to VCC 3.0 4.3 0.15 0.15 0.17 0.18 RFLAT (NO) NO_On-Resistance Flatness (Notes 3, 4) ICOM = 100 mA VIS = 0 to VCC 3.0 4.3 0.12 0.14 0.14 0.16 RON On-Resistance Match Between Channels (Notes 3 and 5) VIS = 1.5 V; ICOM = 100 mA VIS = 2.2 V; ICOM = 100 mA 3.0 0.05 0.05 4.3 0.05 0.05 Symbol Parameter Condition VCC Min -40°C to +85°C Max Min INC(OFF) INO(OFF) NC or NO Off Leakage Current (Note 3) VIN = VIL or VIH VNO or VNC = 0.3 V VCOM = 4.0 V 4.3 -10 10 -100 100 nA ICOM(ON) COM ON Leakage Current (Note 3) VIN = VIL or VIH VNO 0.3 V or 4.0 V with VNC floating or VNC 0.3 V or 4.0 V with VNO floating VCOM = 0.3 V or 4.0 V 4.3 -10 10 -100 100 nA 3. Guaranteed by design. Resistance measurements do not include test circuit or package resistance. 4. Flatness is defined as the difference between the maximum and minimum value of On-resistance as measured over the specified analog signal ranges. 5. RON = RON(MAX) - RON(MIN) between NC1 and NC2 or between NO1 and NO2. http://onsemi.com 3 NLAS52231 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) Guaranteed Maximum Limit Symbol Parameter Test Conditions VCC (V) VIS (V) 25°C Min Typ* -40°C to +85°C Max Min Max Unit tON Turn-On Time RL = 50 , CL = 35 pF (Figures 3 and 4) 2.3 - 4.5 1.5 50 60 ns tOFF Turn-Off Time RL = 50 , CL = 35 pF (Figures 3 and 4) 2.3 - 4.5 1.5 30 40 ns tBBM Minimum Break-Before-Make Time VIS = 3.0 RL = 50 , CL = 35 pF (Figure 2) 3.0 1.5 ns 2 15 Typical @ 25, VCC = 3.6 V CIN Control Pin Input Capacitance 3.5 pF CNO/NC NO, NC Port Capacitance 39 pF CCOM COM Port Capacitance When Switch is Enabled 85 pF *Typical Characteristics are at 25°C. ADDITIONAL APPLICATION CHARACTERISTICS (Voltages Referenced to GND Unless Noted) Symbol Parameter Condition 25°C VCC (V) Typical Unit BW Maximum On-Channel -3 dB Bandwidth or Minimum Frequency Response VIN centered between VCC and GND (Figure 5) 1.65 - 4.5 36 MHz VONL Maximum Feed-through On Loss VIN = 0 dBm @ 100 kHz to 50 MHz VIN centered between VCC and GND (Figure 5) 1.65 - 4.5 -0.06 dB VISO Off-Channel Isolation f = 100 kHz; VIS = 1 V RMS; CL = 5.0 pF VIN centered between VCC and GND (Figure 5) 1.65 - 4.5 -62 dB Q Charge Injection Select Input to Common I/O VIN = VCC to GND, RIS = 0 , CL = 1.0 nF Q = CL x DVOUT (Figure 6) 1.65 - 4.5 53 pC THD Total Harmonic Distortion THD + Noise FIS = 20 Hz to 20 kHz, RL = Rgen = 600 , CL = 50 pF VIS = 2.0 V RMS 3.0 0.03 % VCT Channel-to-Channel Crosstalk f = 100 kHz; VIS = 1.0 V RMS, CL = 5.0 pF, RL = 50 VIN centered between VCC and GND (Figure 5) 1.65 - 4.5 -88 dB 6. Off-Channel Isolation = 20log10 (VCOM/VNO), VCOM = output, VNO = input to off switch. http://onsemi.com 4 NLAS52231 VCC DUT VCC Input Output GND VOUT 0.1 F 50 tBMM 35 pF 90% 90% of VOH Output Switch Select Pin GND Figure 2. tBBM (Time Break-Before-Make) VCC Input DUT VCC 0.1 F 50% Output VOUT Open 50% 0V 50 VOH 90% 35 pF 90% Output VOL Input tON tOFF Figure 3. tON/tOFF VCC VCC Input DUT Output 50 50% VOUT Open 50% 0V VOH 35 pF Output 10% VOL Input tOFF Figure 4. tON/tOFF http://onsemi.com 5 10% tON NLAS52231 50 DUT Reference Transmitted Input Output 50 Generator 50 Channel switch control/s test socket is normalized. Off isolation is measured across an off channel. On loss is the bandwidth of an On switch. VISO, Bandwidth and VONL are independent of the input signal direction. ǒVVOUT Ǔ for VIN at 100 kHz IN VOUT Ǔ for VIN at 100 kHz to 50 MHz VONL = On Channel Loss = 20 Logǒ VIN VISO = Off Channel Isolation = 20 Log Bandwidth (BW) = the frequency 3 dB below VONL VCT = Use VISO setup and test to all other switch analog input/outputs terminated with 50 Figure 5. Off Channel Isolation/On Channel Loss (BW)/Crosstalk (On Channel to Off Channel)/VONL DUT VCC VIN Output Open GND CL Output Off VIN Figure 6. Charge Injection: (Q) http://onsemi.com 6 On Off VOUT NLAS52231 0 0 -10 -0.5 -20 -1 -1.5 -40 BW (dB) XT (dB) -30 -50 -60 -2 -2.5 -3 -70 -3.5 -80 -4 -90 -100 0.01 0.1 1 10 -4.5 0.01 100 0.1 FREQUENCY (MHz) 1 10 100 FREQUENCY (MHz) Figure 7. Cross Talk vs. Frequency @ VCC = 4.3 V Figure 8. Bandwidth vs. Frequency 0.7 0.030 0.65 0.025 0.6 0.55 RON () THD (%) 0.020 0.015 0.010 0.5 0.45 85°C 0.4 25°C 0.35 0.3 0.005 -40°C 0.25 100 1000 10000 100000 0.2 0 0.5 1 1.5 2 2.5 3 FREQUENCY (Hz) VIN (V) Figure 9. Total Harmonic Distortion Figure 10. On-Resistance vs. Input Voltage @ VCC = 3.0 V 0.65 0.46 0.6 0.44 0.55 0.42 0.5 0.40 0.38 0.45 0.4 RON () RON () 0.000 10 85°C 0.35 25°C 0.3 0.25 3.0 V 0.36 0.34 4.3 V 0.32 0.30 0.28 -40°C 0.2 0.26 0.15 0.24 0 0.5 1 1.5 2 2.5 3 3.5 4 0 VIN (V) 0.5 1 1.5 2 2.5 3 3.5 4 VIN (V) Figure 11. On-Resistance vs. Input Voltage @ VCC = 4.3 V Figure 12. On-Resistance vs. Input Voltage http://onsemi.com 7 4.5 NLAS52231 DETAILED DESCRIPTION Overshoot Protection The NLAS52231 features overshoot protection on the signal lines. This allows input signals to exceed the VCC voltage of the switch up to 1.1 V. This is useful in applications where the input signal has a wide dynamic range and may at times exceed the typical signal swing. It is also helpful in designs that pair a moderate signal swing range with a fairly low operating voltage. Up to 1.1 V above VCC, the NLAS52231 switch will pass signals without distortion and maintain all specified performance characteristics. Overshoot Max: VCC + 1.1 V VCC I/O Signal or Any NCx, NOx or COMx Pin GND Figure 13. ORDERING INFORMATION Device NLAS52231MUR2G Package Shipping† UQFN10 (Pb-Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 8 NLAS52231 PACKAGE DIMENSIONS UQFN10 1.4x1.8, 0.4P CASE 488AT-01 ISSUE A EDGE OF PACKAGE ÉÉ ÉÉ ÉÉ D PIN 1 REFERENCE 2X 2X 0.10 C L1 E DETAIL A Bottom View (Optional) 0.10 C B TOP VIEW EXPOSED Cu A 0.05 C 10X A1 0.05 C A1 C SIDE VIEW 3 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. A 5 SEATING PLANE ÉÉ ÉÉ DIM A A1 A3 b D E e L L1 L3 MOLD CMPD A3 DETAIL B Side View (Optional) MILLIMETERS MIN MAX 0.45 0.60 0.00 0.05 0.127 REF 0.15 0.25 1.40 BSC 1.80 BSC 0.40 BSC 0.30 0.50 0.00 0.15 0.40 0.60 SOLDERING FOOTPRINT* 1.700 0.0669 e/2 9XL 0.663 0.0261 6 e 9X 0.563 0.0221 1 10 L3 0.200 0.0079 10 X b 1 0.10 C A B 0.05 C 2.100 0.0827 NOTE 3 BOTTOM VIEW 0.400 0.0157 PITCH 10 X 0.225 0.0089 SCALE 20:1 mm Ǔ ǒinches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P .O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLAS52231/D