ZMDKVG45W Part Number: 3.5x2.8mm PLCC4 SMD LED www.SunLED.com Features z BOTH CHIPS CAN BE CONTROLLED SEPARATELY. z SUITABLE FOR ALL SMT ASSEMBLY AND SOLDER PROCESS. z AVAILABLE z PACKAGE: 1500PCS / REEL. z MOISTURE z RoHS ON TAPE AND REEL. SENSITIVITY LEVEL : LEVEL 4. COMPLIANT. Notes: 1. All dimensions are in millimeters (inches). Operating Characteristics (TA=25°C) 2. Tolerance is ± 0.25(0.01") unless otherwise noted. MDK (InGaAlP) VG (InGaA lP) Unit 3. Specifications are subject to change without notice. Absolute Maximum Ratings (TA=25°C) V Forward Voltage (Max.) (IF=20mA) VF 2.5 2.5 V Reverse Current (Max.) (VR=5V) IR 10 10 uA Wavelength Of Peak Emission (Typ.) (IF=20mA) λP 650 574 nm Wavelength Of Dominant Emission (Typ.) (IF=20mA) λD 635 570 nm Spectral Line Full Width At Half-Maximum (Typ.) (IF=20mA) Δλ 28 20 nm Capacitance (Typ.) (VF=0V, f=1MHz) C 35 15 pF 5 V Forward Current IF 30 30 mA Forward Current (Peak) 1/10Duty Cycle 0.1ms Pulse Width iFS 185 150 mA Power Dissipation PT 75 75 mW Operating Temperature TA -40 ~ +85 Tstg -40 ~ +85 Emitting Color Emitting Material Red InGaAlP Green InGaAlP Published Date : FEB 25, 2008 2.1 Unit 5 ZMDKVG45W 1.95 MDK (InGaAlP) VR Part Number VF VG (InGaA lP) Reverse Voltage Storage Temperature Forward Voltage (Typ.) (IF=20mA) °C Luminous Intensity (IF=20mA) mcd Lens-color Water Clear Drawing No : SDSA1153 V3 Wavelength nm λP min. typ. 70 198 650 18 79 574 Checked : B.L.LIU Viewing Angle 2 θ 1/2 120° P.1/5 Part Number: ZMDKVG45W 3.5x2.8mm PLCC4 SMD LED www.SunLED.com MDK Published Date : FEB 25, 2008 Drawing No : SDSA1153 V3 Checked : B.L.LIU P.2/5 Part Number: ZMDKVG45W 3.5x2.8mm PLCC4 SMD LED www.SunLED.com VG Published Date : FEB 25, 2008 Drawing No : SDSA1153 V3 Checked : B.L.LIU P.3/5 Part Number: ZMDKVG45W 3.5x2.8mm PLCC4 SMD LED www.SunLED.com Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) The device has a single mounting surface. The device must be mounted according to the specifications. Tape Specification (Units : mm) Remarks: If special sorting is required (e.g. binning based on forward voltage, Luminous intensity / luminous flux, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous intensity / Luminous Flux: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. Published Date : FEB 25, 2008 Drawing No : SDSA1153 V3 Checked : B.L.LIU P.4/5 Part Number: 3.5x2.8mm PLCC4 SMD LED www.SunLED.com PACKING & LABEL SPECIFICATIONS Published Date : FEB 25, 2008 ZMDKVG45W Drawing No : SDSA1153 ZMDKVG45W V3 Checked : B.L.LIU P.5/5