DC/DC Converters TEN 30 Series, 30 Watt Features ◆ Smallest encapsulated 30 W converter ◆ 2’’ x 1’’ x 0.4’’ shielded metal package pending with isolated baseplate ◆ Single- and dual output models ◆ I/O isolation voltage 1500 VDC ◆ Excellent efficiency up to 91 % ◆ Operating temp. range –40 °C to +85 °C ◆ Remote On/Off ◆ Over-temperature protection ◆ 3-year product warranty The TEN-30 series is the latest generation of high performance dc-dc converter modules setting a new standard concerning power density. This product with 30W comes in an encapsulated, shielded metal package with a footprint of only 1.0” x 2.0”. All models have wide 2:1 input voltage range and precisely regulated, isolated output voltages. Advanced circuit topology provides high efficiency up to 91% which allows an industrial operating temperature range of –40°C to +85°C (with derating). Further features include remote On/Off, trimmable output, under-voltage lockout and overtemperature protection. Typical applications for these converters are mobile equipment, instrumentation, distributed power architectures in communication and industrial electronics and everywhere where space on the PCB is critical. Models Ordercode TEN 30-1207 TEN 30-1209 TEN 30-1210 TEN 30-1211 TEN 30-1212 TEN 30-1213 TEN 30-1221 TEN 30-1222 TEN 30-1223 TEN 30-2407 TEN 30-2409 TEN 30-2410 TEN 30-2411 TEN 30-2412 TEN 30-2413 TEN 30-2421 TEN 30-2422 TEN 30-2423 TEN 30-4807 TEN 30-4809 TEN 30-4810 TEN 30-4811 TEN 30-4812 TEN 30-4813 TEN 30-4821 TEN 30-4822 TEN 30-4823 http://www.tracopower.com Input voltage 9 – 18 VDC (nominal 12 VDC) 18 – 36 VDC (nominal 24 VDC) 36 – 75 VDC (nominal 48 VDC) Output voltage 1.5 VDC 2.5 VDC 3.3 VDC 5.1 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 1.5 VDC 2.5 VDC 3.3 VDC 5.1 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 1.5 VDC 2.5 VDC 3.3 VDC 5.1 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC Output current max. 8‘500 mA 8‘000 mA 7‘500 mA 6‘000 mA 2‘500 mA 2‘000 mA ± 3‘000 mA ± 1‘250 mA ± 1‘000 mA 8‘500 mA 8‘000 mA 7’500 mA 6‘000 mA 2‘500 mA 2‘000 mA ± 3‘000 mA ± 1‘250 mA ± 1‘000 mA 8‘500 mA 8‘000 mA 7‘500 mA 6‘000 mA 2‘5000 mA 2‘000 mA ± 3‘000 mA ± 1‘250 mA ± 1‘000 mA Efficiency typ. 79 % 84 % 85 % 87 % 89 % 89 % 87 % 87 % 87 % 80 % 85 % 87 % 90 % 91 % 91 % 90 % 89 % 90 % 80 % 85 % 87 % 89 % 91 % 91 % 90 % 88 % 89 % Page 1 of 4 DC/DC Converters TEN 30 Series, 30 Watt Input Specifications Input current at no load 12 V; ±12 / ±15 Vout 12 V; other 24 V; 12 / 15 Vout 24 V; ±12 / ±15 Vout 24 V; other 48 V; ±12 / ±15 Vout 48 V; other models: models: models: models: models: models: models: 50 mA max. 100 mA max. 30 mA max. 30 mA max. 70 mA max. 30 mA max. 45 mA max. Input current at full load 12 V;.1.5 Vout 12 V;.2.5 Vout 12 V;.3.3 Vout 12 V; other output 24 V;.1.5 Vout 24 V;.2.5 Vout 24 V;.3.3 Vout 24 V; other output 48 V;.1.5 Vout 48 V;.2.5 Vout 48 V;.3.3 Vout 48 V; other output models: models: models: models: models: models: models: models: models: models: models: models: 1400 mA typ. 2100 mA typ. 2700 mA typ. 3000 mA typ. 700 mA typ. 1000 mA typ. 1300 mA typ. 1500 mA typ. 350 mA typ. 500 mA typ. 650 mA typ. 750 mA typ. Start-up voltage / under voltage shut down 12 V models: 9 VDC / 8 VDC typ. 24 V models: 18 VDC / 16 VDC typ. 48 V models: 36 VDC / 32 VDC typ. Surge voltage (100 msec. max.) 12 V models: 25 V max. 24 V models: 50 V max.. 48 V models: 100 V max. Conducted noise (input) 12 V models: 24 V models: 48 V models: EN 55022 class A with input capacitor 10 µF / 25 V 1812 MLCC 4.7 µF / 50 V 1812 MLCC 2.2 µF / 100 V 1812 MLCC Output Specifications Voltage set accuracy ±1 % Output voltage adj. range ±10 % (only for single output models) Regulation – – – – – Input variation Vin min. to Vin max. Load variation 0 – 100 % single output models dual output models balanced load dual output models unbalanced load (25% /100%) 0.2 % max. 0.5 % max. 1.0 % max. 5.0 % max. Minimum load not required Temperature coefficient ±0.02 %/K Ripple and noise (20 MHz Bandwidth) 100 mVpk-pk max. (150 mVpk-pk for 12/±12/15/±15V models) Start up time (nominal Vin and constant resistive load) 30 ms typ. Transient response time (25% load change) 250 µs typ. Short circuit protection indefinite, automatic recovery Over load protection 150% of Iout max. typ. Thermal shutdown @ 115 °C typ. Over voltage protection 1.5 2.5 3.3 5.1 12 15 VDC VDC VDC VDC VDC VDC models: models: models: models: models: models: 2.0 V 3.3 V 3.9 V 6.2 V 15 V 18 V All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 4 DC/DC Converters TEN 30 Series, 30 Watt General Specifications Capacitive load Temperature ranges 1.5 / 2.5 / 3.3 5.1 12 15 ±5 ±12 ±15 Vout Vout Vout Vout Vout Vout Vout models: models: models: models: models: models: models: 20’000 µF 14’400 µF 3’000 µF 2’000 µF ±3’000 µF ±2’000 µF ±1’300 µF – Operating – 40 °C to +85 °C – Case temperature +100 °C max. – Storage – 55 °C to +125 °C Load derating 4 %/K above 65°C Humidity (non condensing) 5 % to 95 % rel H max. Thermal inpedance – Natural convection 12 °C/W – Natural convection with heat sink 10 °C/W Reliability, calculated MTBF (MIL-HDBK-217F, @ 25°C, ground benign) 550’000 h Isolation voltage (60 sec.) – Input/Output 1‘500 VDC Isolation capacity – Input/Output 1500 pF max. Isolation resistance – Input/Output (500 VDC) >1’000 MOhm Remote On/Off: – On: 3 to 12 VDC or open circuit. – Off: 0 to 1.2 VDC or short circuit pin 3 and pin 2 – Standby current: 3 mA max. Switching frequency (fixed) 430 kHz typ. (puls width modulation) Vibration and thermal shock MIL-STD-810E Safety standards UL /cUL 60950-1, IEC/EN 60950-1 compliance Safety approvals UL (File no.: tba) Output Voltage Adjustment Trim up Trim down Trim Ru Rd Nominal output voltage at open Trim input! Trim - Vout Ru [kohm] output +5% +10% +Vout Rd [kohm] 1.5 2.5 3.3V 5.1V 12V 0.56 4.3 6.8 5.1 43 0.051 0.33 0.75 0.75 4.3 15V 47 1.8 output –5% –10% 1.5 2.5 3.3V 5.1V 12V 0.68 6.2 8.2 6.2 56 0.062 0.75 0.62 0.82 5.6 15V 56 2.2 Physical Specifications Case material copper, nickel plated Baseplate non conductive FR4 Potting material epoxy (UL 94V-0 -rated) Weight 31 g (1.1 oz) Soldering temperature max. 265°C / 10 sec. All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 3 of 4 DC/DC Converters TEN 30 Series, 30 Watt Outline Dimensions 15.24 (0.6) 5.08 (0.2) Pin-Out 2.54 (0.1) 2.5 (0.1) 50.8 (2.0) 45.72 (1.8) 3 2 1 5 4 5.6 10.16 (0.22) (0.4) 10.2 20.32 (0.4) (0.8) Single Dual 1 +Vin (Vcc) +Vin (Vcc) 2 –Vin (GND) –Vin (GND) 3 Bottom View 6 Pin Remote On/Off 4 + Vout + Vout 5 –Vout Common 6 Trim –Vout Dimensions in [mm], () = Inch Pin diameter: 1.0 ±0.1 (0.04 ±0.004) Pin pitch tolerances: ±0.25 (±0.01) Case tolerances: ±0.5 (±0.02) Heat-Sink (Option) Order code: TEN-HS1 (cont.: heat-sink, thermal pad, 2 clamps) Material: Aluminum Finish: Anodic treatment (black) Weight: 17g (0.60oz) without converter Thermal impedance after assembling: 10 K/W 56.0 (2.2) max. Heat-sink Thermal pad Clamp Converter 16.8 (0.66) max. 14.5 (0.57) Note: The product label on converter has to be removed before mounting the heat-sink. For volume orders converters will be supplied with heat-sinks already mounted. Please contact factory for quotation. Separate heat-sinks are only available for prototypes and small quantity orders. Specifications can be changed any time without notice. Rev. 07/08.1 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · [email protected] · www.tracopower.com Page 4 of 4