AZ725 16 AMP MINIATURE POWER RELAY HIGH INRUSH VERSION 120 AMP FEATURES • Dielectric strength 5000 Vrms • 16 Amp switching - single pole contacts • High inrush version: 120 Amp (20 ms) switching, contact gap > 0.6 mm • Isolation spacing greater than 8mm • Proof tracking index (PTI/CTI) 250 • Reinforced insulation, EN 60730-1 (VDE 0631, part 1) EN 60335-1 (VDE 0700, part 1) • UL, CUR file E43203 • VDE file 40013003 CONTACTS GENERAL DATA Arrangement SPDT (1 Form C) SPST (1 Form A and 1 Form B) Ratings Resistive load: Max. switched power: 480 W or 4000 VA Max. switched current: 16 A Max. switched voltage: 300 VDC* or 400 VAC * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Life Expectancy Mechanical Electrical Minimum operations 3 x 107 1 x 105 at 16 A 250 VAC Res. High inrush version only: 1 x 105 at 1000 W 230 VAC tungsten lamp 3 x 104 at 3000 W 230 VAC tungsten lamp 1 x 104 at 2500 W 230 VAC halogen lamp Operate Time (typical) 7 ms at nominal coil voltage Release Time (typical) 3 ms at nominal coil voltage (with no coil suppression) Rated Load UL, CUR 16 A at 250 VAC resistive VDE 16 A at 250 VAC resistive, 100k cycles Material Silver cadmium oxide or silver tin oxide Resistance < 30 milliohms initially Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts 2000 Vrms between open contacts (1 Form A high inrush version) Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Insulation (according to DIN VDE 0110, IEC 60664-1) C250 Overvoltage category: III Pollution degree: 3 Nominal voltage: 250 VAC Dropout Greater than 10% of nominal coil voltage Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 70°C (158°F) -40°C (-40°F) to 105°C (221°F) Vibration 0.062" (1.5 mm) DA at 10–55 Hz Shock 20 g Enclosure P.B.T. polyester, UL94 V-0 Terminals Tinned copper alloy Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds 2. Relay may pull in with less than “Must Operate” value. Weight 19 grams 3. Specifications subject to change without notice. Packing unit in pcs 50 per plastic tray / 1000 per carton box COIL Power At Pickup Voltage (typical) 270 mW Max. Continuous Dissipation 1.7 W at 20°C (68°F) ambient Temperature Rise 32°C (58°F) nominal coil voltage Temperature Max. 130°C (266°F) NOTES 1. All values at 20°C (68°F). ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2005-08-04 AZ725 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 5 6 Must Operate VDC 3.5 4.2 ORDER NUMBER* Max. Continuous VDC 8.85 10.6 Coil Resistance Ohm ± 10% 49 68 Form A (SPST) AZ725–1A–5D AZ725–1A–6D Form C (SPDT) AZ725–1C–5D AZ725–1C–6D 12 8.4 21.2 260 AZ725–1A–12D AZ725–1C–12D 24 16.8 42.5 1,100 AZ725–1A–24D AZ725–1C–24D 48 33.6 85.0 4,400 AZ725–1A–48D AZ725–1C–48D 60 42.0 106.2 7,000 AZ725–1A–60D AZ725–1C–60D 110 77.0 188.0 20,500 AZ725–1A–110D AZ725–1C–110D * Substitute “1B” in place of “1A” for Form B contacts. Add suffix “E” to “1A” or “1C” for silver tin oxide contacts Substitute “1AS” in place of “1A” for 1 Form A silver tin oxide contacts (120 A high inrush version). MECHANICAL DATA PC BOARD LAYOUT 1.16 MAX (29.5) .516 MAX (13.1) .295 (7.5) .197 (5.0) 1.01 MAX (25.6) .197 (5.0) .590 (15) .142 (3.6) .118 (3.0) .045 (1.1) TYP .016 (0.4) TYP 8 x ø .059 [ø 1.5] Viewed toward terminals WIRING DIAGRAMS Form B Form A 8 5 7 4 1 2 Form C 8 5 7 4 7 4 6 3 6 3 1 2 1 2 Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2005-08-04