CY7C66013C, CY7C66113C Full Speed USB (12 Mbps) Peripheral Controller with Integrated Hub Full Speed USB (12 Mbps) Peripheral Controller with Integrated Hub Features ■ ■ ■ ■ Full speed USB peripheral microcontroller with an integrated USB hub ❐ Well suited for USB compound devices such as a keyboard hub function 8-bit USB optimized microcontroller ❐ Harvard architecture ❐ 6 MHz external clock source ❐ 12 MHz internal CPU clock ❐ 48 MHz internal Hub clock Improved output drivers to reduce electromagnetic interference (EMI) ■ Operating voltage from 4.0 V–5.5 V DC ■ Operating temperature from 0 C–70 C ■ CY7C66013C available in 48-pin SSOP (-PVXC) packages ■ CY7C66113C available in 56-pin QFN or 56-pin SSOP (-PVXC) packages ■ Industry standard programmer support Functional Overview Internal memory ❐ 256 bytes of RAM ❐ 8 kB of PROM Integrated Master and Slave I2C compatible controller (100 kHz) enabled through General Purpose I/O (GPIO) pins ■ Hardware Assisted Parallel Interface (HAPI) for data transfer to external devices ■ I/O ports ❐ Three GPIO ports (Port 0 to 2) capable of sinking 8 mA per pin (typical) ❐ An additional GPIO port (Port 3) capable of sinking 12 mA per pin (typical) for high current requirements: LEDs ❐ Higher current drive achievable by connecting multiple GPIO pins together to drive a common output ❐ Each GPIO port is configured as inputs with internal pull ups or open drain outputs or traditional CMOS outputs ❐ A Digital to Analog Conversion (DAC) port with programmable current sink outputs is available on the CY7C66113C device ❐ Maskable interrupts on all I/O pins ■ 12-bit free running timer with one microsecond clock ticks ■ Watchdog Timer (WDT) ■ Internal Power on Reset (POR) ■ USB Specification compliance ❐ Conforms to USB Specification, Version 1.1 ❐ Conforms to USB HID Specification, Version 1.1 ❐ Supports one or two device addresses with up to five user configured endpoints • Up to two 8-byte control endpoints • Up to four 8-byte data endpoints • Up to two 32-byte data endpoints ❐ Integrated USB transceivers ❐ Supports four downstream USB ports ❐ GPIO pins provide individual power control outputs for each downstream USB port ❐ GPIO pins provide individual port over current inputs for each downstream USB port Cypress Semiconductor Corporation Document Number: 38-08024 Rev. *G ■ The CY7C66013C and CY7C66113C are compound devices with a full speed USB microcontroller in combination with a USB hub. Each device is suited for combination peripheral functions with hubs such as a keyboard hub function. The 8-bit one time programmable microcontroller with a 12 Mbps USB Hub supports as many as four downstream ports. GPIO The CY7C66013C features 29 GPIO pins to support USB and other applications. The I/O pins are grouped into four ports (P0[7:0], P1[7:0], P2[7:0], P3[4:0]) where each port is configured as inputs with internal pull ups, open drain outputs, or traditional CMOS outputs. Ports 0 to 2 are rated at 8 mA per pin (typical) sink current. Port 3 pins are rated at 12 mA per pin (typical) sink current, which allows these pins to drive LEDs. Multiple GPIO pins are connected together to drive a single output for more drive current capacity. Additionally, each I/O pin is used to generate a GPIO interrupt to the microcontroller. All of the GPIO interrupts all share the same “GPIO” interrupt vector. The CY7C66113C has 31 GPIO pins (P0[7:0], P1[7:0], P2[7:0], P3[6:0]). DAC • The CY7C66113C has an additional port P4[7:0] that features an additional eight programmable sink current I/O pins (DAC). Every DAC pin includes an integrated 14 k pull up resistor. When a ‘1’ is written to a DAC I/O pin, the output current sink is disabled and the output pin is driven HIGH by the internal pull up resistor. When a ‘0’ is written to a DAC I/O pin, the internal pull up is disabled and the output pin provides the programmed amount of sink current. A DAC I/O pin is used as an input with an internal pull up by writing a ‘1’ to the pin. The sink current for each DAC I/O pin is individually programmed to one of sixteen values using dedicated Isink registers. DAC bits DAC[1:0] is used as high current outputs with a programmable sink current range of 3.2 to 16 mA (typical). DAC bits DAC[7:2] have a programmable current sink range of 0.2 to 1.0 mA (typical). Multiple DAC pins are connected together to drive a single output that requires more sink current capacity. Each I/O pin is used to generate a DAC interrupt to the microcontroller. Also, the interrupt polarity for each DAC I/O pin is individually programmable. 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised March 1, 2011 [+] Feedback CY7C66013C, CY7C66113C Clock Interrupts The microcontroller uses an external 6 MHz crystal and an internal oscillator to provide a reference to an internal PLL based clock generator. This technology allows the customer application to use an inexpensive 6 MHz fundamental crystal that reduces the clock related noise emissions (EMI). A PLL clock generator provides the 6, 12, and 48 MHz clock signals for distribution within the microcontroller. The microcontroller supports eleven maskable interrupts in the vectored interrupt controller. Interrupt sources include the 128 s (bit 6) and 1.024 ms (bit 9) outputs from the free-running timer, five USB endpoints, the USB hub, the DAC port, the GPIO ports, and the I2C compatible master mode interface. The timer bits cause an interrupt (if enabled) when the bit toggles from LOW ‘0’ to HIGH ‘1.’ The USB endpoints interrupt after the USB host has written data to the endpoint FIFO or after the USB controller sends a packet to the USB host. The DAC ports have an additional level of masking that allows the user to select which DAC inputs causes a DAC interrupt. The GPIO ports also have a level of masking to select which GPIO inputs causes a GPIO interrupt. For additional flexibility, the input transition polarity that causes an interrupt is programmable for each pin of the DAC port. Input transition polarity is programmed for each GPIO port as part of the port configuration. The interrupt polarity can be rising edge (‘0’ to ‘1’) or falling edge (‘1’ to ‘0’). Memory The CY7C66013C and CY7C66113C have 8 kB of PROM. Power on Reset, Watchdog, and Free Running Timer These parts include POR logic, a WDT, and a 12-bit free-running timer. The POR logic detects when power is applied to the device, resets the logic to a known state, and begins executing instructions at PROM address 0x0000. The WDT is used to ensure that the microcontroller recovers after a period of inactivity. The firmware may become inactive for a variety of reasons, including errors in the code or a hardware failure such as waiting for an interrupt that never occurs. I2C and HAPI Interface The microcontroller communicates with external electronics through the GPIO pins. An I2C compatible interface accommodates a 100 kHz serial link with an external device. There is also a HAPI to transfer data to an external device. Timer The free-running 12-bit timer clocked at 1 MHz provides two interrupt sources, 128 s and 1.024 ms. The timer is used to measure the duration of an event under firmware control by reading the timer at the start of the event and after the event is complete. The difference between the two readings indicates the duration of the event in microseconds. The upper four bits of the timer are latched into an internal register when the firmware reads the lower eight bits. A read from the upper four bits actually reads data from the internal register, instead of the timer. This feature eliminates the need for firmware to try to compensate if the upper four bits increment immediately after the lower eight bits are read. Document Number: 38-08024 Rev. *G USB The CY7C66013C and CY7C66113C include an integrated USB Serial Interface Engine (SIE) that supports the integrated peripherals and the hub controller function. The hardware supports up to two USB device addresses with one device address for the hub (two endpoints) and a device address for a compound device (three endpoints). The SIE allows the USB host to communicate with the hub and functions integrated into the microcontroller. The part includes a 1:4 hub repeater with one upstream port and four downstream ports. The USB Hub allows power management control of the downstream ports by using GPIO pins assigned by the user firmware. The user has the option of ganging the downstream ports together with a single pair of power management pins, or providing power management for each port with four pairs of power management pins. Page 2 of 61 [+] Feedback CY7C66013C, CY7C66113C Logic Block Diagram External 6 MHz crystal USB Transceiver D+[0] Upstream D–[0] USB Port PLL USB Transceiver D+[1] D–[1] USB Transceiver D+[2] D–[2] USB SIE USB Transceiver D+[3] D–[3] Interrupt Controller USB Transceiver D+[4] D–[4] 48 MHz Clock Divider 12 MHz 8-bit CPU 12 MHz Repeater RAM 256 byte 8-bit Bus PROM 8 KB Downstream USB Ports 6 MHz 12-bit Timer Watchdog Timer Power-On Reset GPIO PORT 0 P0[0] GPIO PORT 1 P1[0] GPIO/ HAPI PORT 2 Power management under firmware control using GPIO pins P0[7] P1[7] P2[0:1,7] P2[2]; Latch_Empty P2[3]; Data_Ready P2[4]; STB P2[5]; OE P2[6]; CS GPIO PORT 3 P3[0] GPIO PORT 3 P3[5] Additional P3[6] High Current Outputs DAC PORT DAC[0] I2C Interface P3[4] High Current Outputs DAC[7] CY7C66113C only SCLK SDATA *I2C-compatible interface enabled by firmware through P2[1:0] or P1[1:0] Document Number: 38-08024 Rev. *G Page 3 of 61 [+] Feedback CY7C66013C, CY7C66113C Contents Pin Configurations ........................................................... 5 Product Summary Tables ................................................ 9 Pin Assignments .......................................................... 9 I/O Register Summary ................................................. 9 Instruction Set Summary ........................................... 11 Programming Model ....................................................... 12 14-bit Program Counter (PC) .................................... 12 8-bit Accumulator (A) ................................................. 13 8-bit Temporary Register (X) ..................................... 13 8-bit Program Stack Pointer (PSP) ............................ 13 8-bit Data Stack Pointer (DSP) .................................. 13 Address Modes ......................................................... 14 Clocking .......................................................................... 14 Reset ................................................................................ 15 Power on Reset ......................................................... 15 Watchdog Reset ........................................................ 15 Suspend Mode ................................................................ 16 General Purpose I/O (GPIO) Ports ................................ 16 GPIO Configuration Port ........................................... 18 GPIO Interrupt Enable Ports ..................................... 19 DAC Port .......................................................................... 20 DAC Isink Registers .................................................. 21 DAC Port Interrupts ................................................... 21 12-bit Free-Running Timer ............................................. 22 I2C and HAPI Configuration Register ........................... 23 I2C Compatible Controller .............................................. 23 Hardware Assisted Parallel Interface (HAPI) ............... 26 Processor Status and Control Register ....................... 27 Interrupts ......................................................................... 28 Interrupt Vectors ........................................................ 29 Interrupt Latency ....................................................... 30 USB Bus Reset Interrupt ........................................... 30 Timer Interrupt ........................................................... 30 USB Endpoint Interrupts ............................................ 30 USB Hub Interrupt ..................................................... 30 DAC Interrupt ............................................................ 31 GPIO and HAPI Interrupt ........................................... 31 I2C Interrupt ............................................................... 32 Document Number: 38-08024 Rev. *G USB Overview ................................................................. 32 USB Serial Interface Engine ...................................... 32 USB Enumeration ...................................................... 32 USB Hub .......................................................................... 33 Connecting and Disconnecting a USB Device .......... 33 Enabling and Disabling a USB Device ...................... 34 Hub Downstream Ports Status and Control .............. 35 Downstream Port Suspend and Resume .................. 36 USB Upstream Port Status and Control .................... 38 USB SIE Operation ......................................................... 39 USB Device Addresses ............................................. 39 USB Device Endpoints .............................................. 39 USB Control Endpoint Mode Registers ..................... 39 USB Non Control Endpoint Mode Registers ............. 41 USB Endpoint Counter Registers .............................. 41 Endpoint Mode and Count Registers Update and Locking Mechanism .......................................................... 42 USB Mode Tables ........................................................... 44 Register Summary .......................................................... 48 Sample Schematic .......................................................... 50 Absolute Maximum Ratings .......................................... 51 Electrical Characteristics ............................................... 51 Switching Characteristics .............................................. 52 Ordering Information ...................................................... 55 Ordering Code Definitions ......................................... 55 Package Diagrams .......................................................... 56 Quad Flat Package No Leads (QFN) Package Design Notes ................................................................... 58 Acronyms ........................................................................ 59 Document Conventions ................................................. 59 Units of Measure ....................................................... 59 Document History Page ................................................. 60 Sales, Solutions, and Legal Information ...................... 61 Worldwide Sales and Design Support ....................... 61 Products .................................................................... 61 PSoC Solutions ......................................................... 61 Page 4 of 61 [+] Feedback CY7C66013C, CY7C66113C Pin Configurations Figure 1. CY7C66013C 48-pin SSOP and CY7C66113C 56-pin SSOP TOP VIEW CY7C66113C CY7C66013C XTALOUT 1 48 VCC XTALOUT 1 56 VCC XTALIN 2 47 P1[1] XTALIN 2 55 P1[1] VREF 3 46 P1[0] VREF 3 54 P1[0] P1[3] 4 45 P1[2] P1[3] 4 53 P1[2] P1[5] 5 44 P1[4] P1[5] 5 52 P1[4] P1[7] 6 43 P1[6] P1[7] 6 51 P1[6] P3[1] 7 42 P3[0] P3[1] 7 50 P3[0] D+[0] 8 41 D–[3] D+[0] 8 49 D–[3] 9 48 D+[3] D–[0] 9 40 D+[3] D–[0] P3[3] 10 39 P3[2] P3[3] 10 47 P3[2] GND 11 38 GND GND 11 46 P3[4] D+[1] 12 37 P3[4] P3[5] 12 45 D–[4] D–[1] 13 36 D–[4] D+[1] 13 44 D+[4] P2[1] 14 35 D+[4] D–[1] 14 43 P3[6] D+[2] 15 34 P2[0] P2[1] 15 42 P2[0] D–[2] 16 33 P2[2] D+[2] 16 41 P2[2] P2[3] 17 32 GND D–[2] 17 40 GND P2[5] 18 31 P2[4] P2[3] 18 39 P2[4] P2[7] 19 30 P2[6] P2[5] 19 38 P2[6] GND 20 29 VPP P2[7] 20 37 DAC[0] P0[7] 21 28 P0[0] DAC[7] 21 36 VPP P0[5] 22 27 P0[2] P0[7] 22 35 P0[0] P0[3] 23 26 P0[4] P0[5] 23 34 P0[2] P0[1] 24 25 P0[6] P0[3] 24 33 P0[4] P0[1] 25 32 P0[6] DAC[5] 26 31 DAC[2] DAC[3] 27 30 DAC[4] DAC[1] 28 29 DAC[6] Document Number: 38-08024 Rev. *G Page 5 of 61 [+] Feedback CY7C66013C, CY7C66113C Figure 2. CY7C66113C 56-pin QFN D+[0] P3[1] P1[7] P1[5] P1[3] Vref XTALIN XTALOUT Vcc P1[1] P1[0] P1[2] P1[4] P1[6] 56 55 54 53 52 51 50 49 48 47 46 45 44 43 D-[0] 1 42 P3[0] P3[3] 2 41 D–[3] GND 3 40 D+[3] P3[5] 4 39 P3[2] D+[1] 5 38 P3[4] D–[1] 6 37 D–[4] P2[1] 7 36 D+[4] D+[2] 8 35 P3[6] D–[2] 9 34 P2[0] P2[3] 10 33 P2[2] P2[5] 11 32 GND P2[7] 12 31 P2[4] DAC[7] 13 30 P2[6] P0[7] 14 29 DAC[0] CY7C66113C 56-pin QFN 15 16 17 18 19 20 21 22 23 24 25 26 27 28 P0[5] P0[3] P0[1] DAC[5] DAC[3] DAC[1] DAC[6] DAC[4] DAC[2] P0[6] P0[4] P0[2] P0[0] Vpp Document Number: 38-08024 Rev. *G Page 6 of 61 [+] Feedback CY7C66013C, CY7C66113C Figure 3. CY7C66113C DIE (3398, 4194) Cypress Logo Pin 1 Pin 60 Pin 15 Pin 30 Pin 45 (0,0) DIE STEP: 3398 x 4194 microns Die Size: 3322 x 4129 microns Die Thickness: 14 mils = 355.6 microns Pad Size: 80 x 80 microns Document Number: 38-08024 Rev. *G Page 7 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 1. Pad Coordinates in Microns (0,0) to Bond Pad Centers Pad No. Pin Name X Y Pad # Pin Name X Y 1 XtalOut 1274.2 3588.8 37 DAC6 2000.6 210.6 2 XtalIn 1132.8 3588.8 38 DAC4 2103.6 210.6 3 Vref 889.85 3588.8 39 DAC2 2206.6 210.6 4 Port11b 684.65 3588.8 40 Port06 2308.4 210.6 5 Port13 581.65 3588.8 41 Port04 2411.4 210.6 6 Port15 478.65 3588.8 42 Port02 2514.4 210.6 7 Vss 375.65 3588.8 43 Port00 2617.4 210.6 8 Port17 0 3408.35 44 Vpp 2992.4 25.4 9 Port31 0 3162.05 45 DAC0 2992.4 151.75 10 Du+ 0 3060.55 46 Port26 2992.4 306.15 11 Du– 0 2752.4 47 DD+6 2992.4 407.65 12 Port33 0 2650.95 48 DD–6 2992.4 715.75 13 Vss 0 2474.6 49 Port24 2992.4 817.25 14 Port35 0 2368.45 50 Vss 2992.4 923.4 15 DD+1 0 2266.95 51 Port22 2992.4 1086.75 16 DD–1 0 1958.85 52 DD+5 2992.4 1188.25 17 Port37 0 1857.35 53 DD–5 2992.4 1496.35 18 Vref 0 1680.4 54 Port20 2992.4 1597.85 19 Port21 0 1567.4 55 Vref 2992.4 1710.8 20 DD+2 0 1465.95 56 Port36 2992.4 1874.75 21 DD–2 0 1157.85 57 DD+4 2992.4 1976.25 22 Port23 0 1056.35 58 DD–4 2992.4 2284.35 23 Vss 0 880 59 Port34 2992.4 2385.85 24 Port25 0 773.85 60 Vss 2992.4 2492 25 DD+7 0 672.35 61 Port32 2992.4 2655.35 26 DD–7 0 364.25 62 DD+3 2992.4 2756.85 27 Port27 0 262.75 63 DD–3 2992.4 3064.95 28 DAC7 0 100.75 64 Port30 2992.4 3166.45 29 Vss 0 0 65 Port16 2992.4 3412.25 30 Port07 375.2 210.6 66 Port14 2634.2 3588.8 31 Port05 478.2 210.6 67 Port12 2531.2 3588.8 32 Port03 581.2 210.6 68 Port10 2428.2 3588.8 33 Port01 684.2 210.6 69 Port11 2325.2 3588.8 34 DAC5 788.4 210.6 70 VCC 2221.75 3588.8 35 DAC3 891.4 210.6 71 PadOpt 2121.75 3588.8 36 DAC1 994.4 210.6 Document Number: 38-08024 Rev. *G Page 8 of 61 [+] Feedback CY7C66013C, CY7C66113C Product Summary Tables Pin Assignments Table 2. Pin Assignments Name I/O 48-pin 56-pin QFN 56-pin SSOP Description D+[0], D–[0] I/O 8, 9 56, 1 8, 9 Upstream port, USB differential data. D+[1], D–[1] I/O 12, 13 5, 6 13, 14 Downstream port 1, USB differential data. D+[2], D–[2] I/O 15, 16 8, 9 16, 17 Downstream port 2, USB differential data. D+[3], D–[3] I/O 40, 41 40, 41 48, 49 Downstream port 3, USB differential data. 44, 45 Downstream port 4, USB differential data. D+[4], D–[4] I/O 35, 36 36, 37 P0[7:0] I/O 21, 25, 22, 26, 23, 27, 24, 28 14, 15, 16, 17, 22, 32, 23, 33, GPIO Port 0. 24, 25, 26, 27 24, 34, 25, 35 P1[7:0] I/O 6, 43, 5, 44, 4, 45, 47, 46 52, 53, 54, 43, 6, 51, 5, 52, 4, GPIO Port 1. 44, 45, 46, 47 53, 55, 54 P2[7:0] I/O 19, 30, 18, 31, 17, 33, 14, 34 7, 10, 11, 12, 20, 38, 19, 39, GPIO Port 2. 30, 31, 33, 34 18, 41, 15, 42 P3[6:0] I/O 37, 10, 39, 7, 42 55, 2, 4, 35, 38, 39, 42, DAC[7:0] I/O n/a 13, 18, 19, 20, 21, 29, 26, 30, Digital to Analog Converter (DAC) Port with programmable 21, 22, 23, 29 27, 31, 28, 37 current sink outputs. DAC[1:0] offer a programmable range of 3.2 to 16 mA typical. DAC[7:2] have a programmable sink current range of 0.2 to 1.0 mA typical. IN 2 50 2 6 MHz crystal or external clock input. OUT 1 49 1 6 MHz crystal out. Programming voltage supply, tie to ground during normal operation. XTALIN XTALOUT 43, 12, 46, 10, GPIO Port 3, capable of sinking 12 mA (typical). 47, 7, 50 VPP 29 28 36 VCC 48 48 56 Voltage supply. GND 11, 20, 32, 38 3, 32 11, 40 Ground. 3 51 3 External 3.3 V supply voltage for the differential data output buffers and the D+ pull up. VREF IN I/O Register Summary I/O registers are accessed via the I/O Read (IORD) and I/O Write (IOWR, IOWX) instructions. IORD reads data from the selected port into the accumulator. IOWR performs the reverse; it writes data from the accumulator to the selected port. Indexed I/O Write (IOWX) adds the contents of X to the address in the instruction to form the port address and writes data from the accumulator to the specified port. Specifying address 0 such as IOWX 0h indicates the I/O register is selected solely by the contents of X. All undefined registers are reserved. It is important not to write to reserved registers as this may cause an undefined operation or increased current consumption during operation. When writing to registers with reserved bits, the reserved bits must be written with ‘0.’ Table 3. I/O Register Summary I/O Address Read/Write Port 0 Data Register Name 0x00 R/W GPIO Port 0 Data 16 Port 1 Data 0x01 R/W GPIO Port 1 Data 17 Port 2 Data 0x02 R/W GPIO Port 2 Data 17 Port 3 Data 0x03 R/W GPIO Port 3 Data 17 Port 0 Interrupt Enable 0x04 W Interrupt Enable for Pins in Port 0 19 Port 1 Interrupt Enable 0x05 W Interrupt Enable for Pins in Port 1 19 Port 2 Interrupt Enable 0x06 W Interrupt Enable for Pins in Port 2 19 Port 3 Interrupt Enable 0x07 W Interrupt Enable for Pins in Port 3 19 GPIO Configuration 0x08 R/W GPIO Port Configurations 18 Document Number: 38-08024 Rev. *G Function Page Page 9 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 3. I/O Register Summary (continued) Register Name I/O Address Read/Write Function Page 2 2 HAPI and I C Configuration 0x09 R/W HAPI Width and I C Position Configuration 23 USB Device Address A 0x10 R/W USB Device Address A 39 EP A0 Counter Register 0x11 R/W USB Address A, Endpoint 0 Counter 41 EP A0 Mode Register 0x12 R/W USB Address A, Endpoint 0 Configuration 40 EP A1 Counter Register 0x13 R/W USB Address A, Endpoint 1 Counter 41 EP A1 Mode Register 0x14 R/W USB Address A, Endpoint 1 Configuration 41 EP A2 Counter Register 0x15 R/W USB Address A, Endpoint 2 Counter 41 EP A2 Mode Register 0x16 R/W USB Address A, Endpoint 2 Configuration 41 USB Status & Control 0x1F R/W USB Upstream Port Traffic Status and Control 38 Global Interrupt Enable 0x20 R/W Global Interrupt Enable 28 Endpoint Interrupt Enable 0x21 R/W USB Endpoint Interrupt Enables 28 Interrupt Vector 0x23 R Pending Interrupt Vector Read/Clear 30 Timer (LSB) 0x24 R Lower 8 Bits of Free-running Timer (1 MHz) 22 Timer (MSB) 0x25 R Upper 4 Bits of Free-running Timer 22 WDT Clear 0x26 W Watchdog Timer Clear 15 I2C Control & Status 0x28 R/W I2C Status and Control 24 0x29 R/W I2C 24 0x30 R/W DAC Data I2C Data DAC Data Data 20 DAC Interrupt Enable 0x31 W Interrupt Enable for each DAC Pin 21 DAC Interrupt Polarity 0x32 W Interrupt Polarity for each DAC Pin 21 0x38-0x3F W Input Sink Current Control for each DAC Pin 21 0x40 R/W USB Device Address B (not used in 5-endpoint mode) 39 DAC Isink USB Device Address B EP B0 Counter Register 0x41 R/W USB Address B, Endpoint 0 Counter 41 EP B0 Mode Register 0x42 R/W USB Address B, Endpoint 0 Configuration, or USB Address A, Endpoint 3 in 5-endpoint Mode 40 EP B1 Counter Register 0x43 R/W USB Address B, Endpoint 1 Counter 41 EP B1 Mode Register 0x44 R/W USB Address B, Endpoint 1 Configuration, or USB Address A, Endpoint 4 in 5-endpoint Mode 41 Hub Port Connect Status 0x48 R/W Hub Downstream Port Connect Status 33 Hub Port Enable 0x49 R/W Hub Downstream Ports Enable 34 Hub Port Speed 0x4A R/W Hub Downstream Ports Speed 34 Hub Port Control (Ports [4:1]) 0x4B R/W Hub Downstream Ports Control 35 Hub Port Suspend 0x4D R/W Hub Downstream Port Suspend Control 36 Hub Port Resume Status 0x4E R Hub Downstream Ports Resume Status 37 Hub Ports SE0 Status 0x4F R Hub Downstream Ports SE0 Status 36 Hub Ports Data 0x50 R Hub Downstream Ports Differential Data 36 Hub Downstream Force Low 0x51 R/W Hub Downstream Ports Force LOW 35 Processor Status & Control 0xFF R/W Microprocessor Status and Control Register 27 Document Number: 38-08024 Rev. *G Page 10 of 61 [+] Feedback CY7C66013C, CY7C66113C Instruction Set Summary Refer to the CYASM Assembler User’s Guide for more details. Table 4. Instruction Set Summary Mnemonic Operand HALT Opcode Cycles Mnemonic Operand Opcode Cycles 00 7 NOP 01 4 INC A acc 6 INC X x 22 4 7 INC [expr] direct 23 7 4 INC [X+expr] index 24 8 6 DEC A acc 25 4 06 7 DEC X x 26 4 07 4 DEC [expr] direct 27 7 ADD A,expr data ADD A,[expr] direct 02 ADD A,[X+expr] index 03 ADC A,expr data 04 ADC A,[expr] direct 05 ADC A,[X+expr] index SUB A,expr data 20 4 21 4 SUB A,[expr] direct 08 6 DEC [X+expr] index 28 8 SUB A,[X+expr] index 09 7 IORD expr address 29 5 SBB A,expr data 0A 4 IOWR expr address 2A 5 SBB A,[expr] direct 0B 6 POP A 2B 4 SBB A,[X+expr] index 0C 7 POP X 2C 4 OR A,expr data 0D 4 PUSH A 2D 5 OR A,[expr] direct 0E 6 PUSH X 2E 5 OR A,[X+expr] index 0F 7 SWAP A,X 2F 5 AND A,expr data 10 4 SWAP A,DSP AND A,[expr] direct 11 6 MOV [expr],A direct 30 5 31 5 AND A,[X+expr] index 12 7 MOV [X+expr],A index 32 6 XOR A,expr data 13 4 OR [expr],A direct 33 7 XOR A,[expr] direct 14 6 OR [X+expr],A index 34 8 XOR A,[X+expr] index 15 7 AND [expr],A direct 35 7 CMP A,expr data 16 5 AND [X+expr],A index 36 8 CMP A,[expr] direct 17 7 XOR [expr],A direct 37 7 CMP A,[X+expr] index 18 8 XOR [X+expr],A index 38 8 MOV A,expr data 19 4 IOWX [X+expr] index 39 6 MOV A,[expr] direct 1A 5 CPL 3A 4 MOV A,[X+expr] index 1B 6 ASL 3B 4 MOV X,expr data 1C 4 ASR 3C 4 MOV X,[expr] direct 1D 5 RLC 3D 4 reserved 1E RRC 3E 4 XPAGE 1F 4 RET 3F 8 MOV A,X 40 4 DI 70 4 MOV X,A 41 4 EI 72 4 MOV PSP,A CALL addr 60 4 RETI 73 8 50-5F 10 JC addr C0-CF 5 JMP addr 80-8F 5 JNC addr D0-DF 5 CALL addr 90-9F 10 JACC addr E0-EF 7 JZ addr A0-AF 5 INDEX addr F0-FF 14 JNZ addr B0-BF 5 Document Number: 38-08024 Rev. *G Page 11 of 61 [+] Feedback CY7C66013C, CY7C66113C Programming Model 14-bit Program Counter (PC) The 14-bit PC allows access to up to 8 kB of PROM available with the CY7C66x13C architecture. The top 32 bytes of the ROM in the 8K part are reserved for testing purposes. The program counter is cleared during reset, such that the first instruction executed after a reset is at address 0x0000h. Typically, this is a jump instruction to a reset handler that initializes the application (see Interrupt Vectors on page 29). The lower eight bits of the program counter are incremented as instructions are loaded and executed. The upper six bits of the program counter are incremented by executing an XPAGE instruction. The last instruction executed within a 256-byte “page” of sequential code should be an XPAGE instruction. The assembler directive “XPAGEON” causes the assembler to insert XPAGE instructions automatically. Because instructions are either one or two bytes long, the assembler may occasionally need to insert a NOP followed by an XPAGE to execute correctly. The address of the next instruction to be executed, the carry flag, and the zero flag are saved as two bytes on the program stack during an interrupt acknowledge or a CALL instruction. The program counter, carry flag, and zero flag are restored from the program stack during a RETI instruction. Only the program counter is restored during a RET instruction. The program counter is not accessed directly by the firmware. The program stack is examined by reading SRAM from location 0x00 and up. Program Memory Organization Table 5. Program Memory Space with Interrupt Vector Table After Reset Address 14-bit PC 0x0000 Program execution begins here after a reset 0x0002 USB bus reset interrupt vector 0x0004 128 s timer interrupt vector 0x0006 1.024 ms timer interrupt vector 0x0008 USB address A endpoint 0 interrupt vector 0x000A USB address A endpoint 1 interrupt vector 0x000C USB address A endpoint 2 interrupt vector 0x000E USB address B endpoint 0 interrupt vector 0x0010 USB address B endpoint 1 interrupt vector 0x0012 Hub interrupt vector 0x0014 DAC interrupt vector 0x0016 GPIO/HAPI interrupt vector 0x0018 I2C interrupt vector 0x001A Program Memory begins here 0x1FDF 8 kB (-32) PROM ends here. Document Number: 38-08024 Rev. *G Page 12 of 61 [+] Feedback CY7C66013C, CY7C66113C 8-bit Accumulator (A) The accumulator is the general purpose register for the microcontroller. 8-bit Temporary Register (X) The “X” register is available to the firmware for temporary storage of intermediate results. The microcontroller performs indexed operations based on the value in X. Refer to the section, Indexed on page 14 for additional information. 8-bit Program Stack Pointer (PSP) During a reset, the Program Stack Pointer (PSP) is set to 0x00 and “grows” upward from this address. The PSP may be set by firmware, using the MOV PSP,A instruction. The PSP supports interrupt service under hardware control and CALL, RET, and RETI instructions under firmware control. The PSP is not readable by the firmware. During an interrupt acknowledge, interrupts are disabled and the 14-bit program counter, carry flag, and zero flag are written as two bytes of data memory. The first byte is stored in the memory addressed by the PSP, then the PSP is incremented. The second byte is stored in memory addressed by the PSP, and the PSP is incremented again. The overall effect is to store the program Table 6. SRAM Areas After Reset 8-bit DSP 8-bit PSP counter and flags on the program “stack” and increment the PSP by two. The Return From Interrupt (RETI) instruction decrements the PSP, then restores the second byte from memory addressed by the PSP. The PSP is decremented again and the first byte is restored from memory addressed by the PSP. After the program counter and flags are restored from stack, the interrupts are enabled. The overall effect is to restore the program counter and flags from the program stack, decrement the PSP by two, and re-enable interrupts. The Call Subroutine (CALL) instruction stores the program counter and flags on the program stack and increments the PSP by two. The Return From Subroutine (RET) instruction restores the program counter but not the flags from the program stack and decrements the PSP by two. Data Memory Organization The CY7C66x13C microcontrollers provide 256 bytes of data RAM. Normally, the SRAM is partitioned into four areas: program stack, user variables, data stack, and USB endpoint FIFOs. The following is one example of where the program stack, data stack, and user variables areas are located. Address Program Stack Growth 0x00 (Move DSP[1]) 8-bit DSP Data Stack Growth User Selected User variables USB FIFO space for up to two addresses and five endpoints[2] 0xFF 8-bit Data Stack Pointer (DSP) The Data Stack Pointer (DSP) supports PUSH and POP instructions that use the data stack for temporary storage. A PUSH instruction pre-decrements the DSP, then writes data to the memory location addressed by the DSP. A POP instruction reads data from the memory location addressed by the DSP, then post-increments the DSP. During a reset, the DSP is reset to 0x00. A PUSH instruction when DSP equals 0x00 writes data at the top of the data RAM (address 0xFF). This writes data to the memory area reserved for USB endpoint FIFOs. Therefore, the DSP should be indexed at an appropriate memory location that does not compromise the Program Stack, user defined memory (variables), or the USB endpoint FIFOs. For USB applications, the firmware should set the DSP to an appropriate location to avoid a memory conflict with RAM dedicated to USB FIFOs. The memory requirements for the USB endpoints are described in USB Device Endpoints on page 39. Example assembly instructions to do this with two device addresses (FIFOs begin at 0xD8) are shown: ■ MOV A,20h; Move 20 hex into Accumulator (must be D8h or less) ■ SWAP A,DSP; swap accumulator value into DSP register. Notes 1. Refer to 8-bit Data Stack Pointer (DSP) for a description of DSP. 2. Endpoint sizes are fixed by the Endpoint Size Bit (I/O register 0x1F, Bit 7), see Table 47. Document Number: 38-08024 Rev. *G Page 13 of 61 [+] Feedback CY7C66013C, CY7C66113C Address Modes The CY7C66013C and CY7C66113C microcontrollers support three addressing modes for instructions that require data operands: data, direct, and indexed. Data (Immediate) “Data” address mode refers to a data operand that is actually a constant encoded in the instruction. As an example, consider the instruction that loads A with the constant 0xD8: MOV A, 0D8h. This instruction requires two bytes of code where the first byte identifies the “MOV A” instruction with a data operand as the second byte. The second byte of the instruction is the constant “0xD8”. A constant may be referred to by name if a prior “EQU” statement assigns the constant value to the name. For example, the following code is equivalent to the example described earlier: DSPINIT: EQU 0D8h MOV A, DSPINIT. Direct “Direct” address mode is used when the data operand is a variable stored in SRAM. In that case, the one byte address of the variable is encoded in the instruction. As an example, consider an instruction that loads A with the contents of memory address location 0x10: MOV A, [10h]. Normally, variable names are assigned to variable addresses using “EQU” statements to improve the readability of the assembler source code. As an example, the following code is equivalent to the example described earlier: buttons: EQU 10h MOV A, [buttons]. Clocking Figure 4. Clock Oscillator On-Chip Circuit XTALOUT (pin 1) XTALIN (pin 2) To Internal PLL 30 pF 30 pF The XTALIN and XTALOUT are the clock pins to the microcontroller. The user connects an external oscillator or a crystal to these pins. When using an external crystal, keep PCB traces between the chip leads and crystal as short as possible (less than 2 cm). A 6 MHz fundamental frequency parallel resonant crystal is connected to these pins to provide a reference frequency for the internal PLL. The two internal 30 pF load caps appear in series to the external crystal and would be equivalent to a 15 pF load. Therefore, the crystal must have a required load capacitance of about 15–18 pF. A ceramic resonator does not allow the microcontroller to meet the timing specifications of full speed USB and so a ceramic resonator is not recommended with these parts. An external 6 MHz clock is applied to the XTALIN pin if the XTALOUT pin is left open. Grounding the XTALOUT pin when driving XTALIN with an oscillator does not work because the internal clock is effectively shorted to ground. Indexed “Indexed” address mode allows the firmware to manipulate arrays of data stored in SRAM. The address of the data operand is the sum of a constant encoded in the instruction and the contents of the “X” register. Normally, the constant is the “base” address of an array of data and the X register contains an index that indicates which element of the array is actually addressed: array: EQU 10h MOV X, 3 MOV A, [X+array]. This has the effect of loading A with the fourth element of the SRAM “array” that begins at address 0x10. The fourth element would be at address 0x13. Document Number: 38-08024 Rev. *G Page 14 of 61 [+] Feedback CY7C66013C, CY7C66113C Reset The CY7C66x13C supports two resets: POR and a Watchdog Reset (WDR). Each of these resets causes: ■ All registers to be restored to their default states. ■ The USB device addresses to be set to 0. ■ All interrupts to be disabled. ■ The PSP and DSP to be set to memory address 0x00. The occurrence of a reset is recorded in the Processor Status and Control Register, as described in Processor Status and Control Register on page 27. Bits 4 and 6 are used to record the occurrence of POR and WDR, respectively. Firmware interrogates these bits to determine the cause of a reset. Program execution starts at ROM address 0x0000 after a reset. Although this looks similar to interrupt vector 0, there is an important difference. Reset processing does NOT push the program counter, carry flag, and zero flag onto program stack. The firmware reset handler should configure the hardware before the “main” loop of code. Attempting to execute a RET or RETI in the firmware reset handler causes unpredictable execution results. Power on Reset When VCC is first applied to the chip, the POR signal is asserted and the CY7C66x13C enters a “semi-suspend” state. During the semi-suspend state, which is different from the suspend state defined in the USB specification, the oscillator and all other blocks of the part are functional, except for the CPU. This semi-suspend time ensures that both a valid VCC level is reached and that the internal PLL has time to stabilize before full operation begins. When the VCC rises above approximately 2.5 V, and the oscillator is stable, the POR is deasserted and the on-chip timer starts counting. The first 1 ms of suspend time is not interruptible, and the semi-suspend state continues for an additional 95 ms unless the count is bypassed by a USB Bus Reset on the upstream port. The 95 ms provides time for VCC to stabilize at a valid operating voltage before the chip executes code. If a USB Bus Reset occurs on the upstream port during the 95 ms semi-suspend time, the semi-suspend state is aborted and program execution begins immediately from address 0x0000. In this case, the Bus Reset interrupt is pending but not serviced until firmware sets the USB Bus Reset Interrupt Enable bit (bit 0 of register 0x20) and enables interrupts with the EI command. The POR signal is asserted whenever VCC drops below approximately 2.5 V, and remains asserted until VCC rises above this level again. Behavior is the same as described earlier. Watchdog Reset The WDR occurs when the internal WDT rolls over. Writing any value to the write only Watchdog Restart Register at address 0x26 clears the timer. The timer rolls over and WDR occurs if it is not cleared within tWATCH (8 ms minimum) of the last clear. Bit 6 of the Processor Status and Control Register is set to record this event (the register contents are set to 010X0001 by the WDR). A WDT Reset lasts for 2 ms, after which the microcontroller begins execution at ROM address 0x0000. The USB transmitter is disabled by a WDR because the USB Device Address Registers are cleared (see USB Device Addresses on page 39). Otherwise, the USB Controller responds to all address 0 transactions. It is possible to set the WDR bit of the Processor Status and Control Register (0xFF) following a POR event. If a firmware interrogates the Processor Status and Control Register for a set condition on the WDR bit, the WDR bit should be ignored if the POR (bit 3 of register 0xFF) bit is set. Figure 5. Watchdog Reset tWATCH Last write to WDT Register Document Number: 38-08024 Rev. *G 2 ms No write to WDT register, so WDR goes HIGH Execution begins at Reset Vector 0x0000 Page 15 of 61 [+] Feedback CY7C66013C, CY7C66113C Suspend Mode The CY7C66x13C is placed into a low power state by setting the Suspend bit of the Processor Status and Control register. All logic blocks in the device are turned off except the GPIO interrupt logic and the USB receiver. The clock oscillator, PLL, and the free-running and WDTs are shut down. Only the occurrence of an enabled GPIO interrupt or non idle bus activity at a USB upstream or downstream port wakes the part from suspend. The Run bit in the Processor Status and Control Register must be set to resume a part out of suspend. The clock oscillator restarts immediately after exiting suspend mode. The microcontroller returns to a fully functional state 1 ms after the oscillator is stable. The microcontroller executes the instruction following the I/O write that placed the device into suspend mode before servicing any interrupt requests. The GPIO interrupt allows the controller to wake up periodically and poll system components while maintaining a very low average power consumption. To achieve the lowest possible current during suspend mode, all I/O should be held at VCC or Gnd. This also applies to internal port pins that may not be bonded in a particular package. Typical code for entering suspend is given here: ... ; All GPIO set to low power state (no floating pins) ... ; Enable GPIO interrupts if desired for wakeup mov a, 09h; Set suspend and run bits iowr FFh; Write to Status and Control Register – Enter suspend, wait for USB activity (or GPIO Interrupt) nop ; This executes before any ISR General Purpose I/O (GPIO) Ports Figure 6. Block Diagram of a GPIO Pin VCC GPIO CFG mode 2-bits OE Data Out Latch Control Internal Data Bus Q1 14 k GPIO PIN Port Write Port Read Q2 Q3* Data In Latch STRB (Latch is Transparent except in HAPI mode) Data Interrupt Latch Control Reg_Bit Interrupt Enable Interrupt Controller *Port 0,1,2: Low Isink Port 3: High Isink There are up to 31 GPIO pins (P0[7:0], P1[7:0], P2[7:0], and P3[6:0]) for the hardware interface. The number of GPIO pins changes based on the package type of the chip. Each port is configured as inputs with internal pull ups, open drain outputs, or traditional CMOS outputs. Port 3 offers a higher current drive, with typical current sink capability of 12 mA. The data for each GPIO port is accessible through the data registers. Port data registers are shown in Table 7 on page 17 through Table 10 on page 17, and are set to 1 on reset. Document Number: 38-08024 Rev. *G Page 16 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 7. Port 0 Data Port 0 Data Bit # 7 6 5 4 3 2 1 ADDRESS 0x00 0 Bit Name P0.7 P0.6 P0.5 P0.4 P0.3 P0.2 P0.1 P0.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 1 1 1 1 1 1 1 1 Table 8. Port1 Data Port 1Data Bit # ADDRESS 0x01 0 7 6 5 4 3 2 1 Bit Name P1.7 P1.6 P1.5 P1.4 P1.3 P1.2 P1.1 P1.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 1 1 1 1 1 1 1 1 Table 9. Port 2 Data Port 2 Data Bit # ADDRESS 0x02 0 7 6 5 4 3 2 1 Bit Name P2.7 P2.6 P2.5 P2.4 P2.3 P2.2 P2.1 P2.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 1 1 1 1 1 1 1 1 3 2 1 Table 10. Port 3 Data Port 3 Data Bit # 5 4 ADDRESS 0x03 0 7 6 Bit Name Reserved P3.4 P3.5 P3.6 CY7C66113C CY7C66113C only only P3.3 P3.2 P3.1 P3.0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset - 1 1 1 1 1 1 1 Special care should be taken with any unused GPIO data bits. An unused GPIO data bit, either a pin on the chip or a port bit that is not bonded on a particular package, must not be left floating when the device enters the suspend state. If a GPIO data bit is left floating, the leakage current caused by the floating bit may violate the suspend current limitation specified by the USB specifications. If a ‘1’ is written to the unused data bit and the port is configured with open drain outputs, the unused data bit remains in an indeterminate state. Therefore, if an unused port bit is programmed in open-drain mode, it must be written with a ‘0.’ Notice that the CY7C66013C always requires that P3[7:5] be written with a ‘0.’ When the CY7C66113C is used the P3[7] should be written with a ‘0.’ Document Number: 38-08024 Rev. *G In normal non HAPI mode, reads from a GPIO port always return the present state of the voltage at the pin, independent of the settings in the Port Data Registers. If HAPI mode is activated for a port, reads of that port return latched data as controlled by the HAPI signals (see Hardware Assisted Parallel Interface (HAPI) on page 26). During reset, all of the GPIO pins are set to a high impedance input state (‘1’ in open drain mode). Writing a ‘0’ to a GPIO pin drives the pin LOW. In this state, a ‘0’ is always read on that GPIO pin unless an external source overdrives the internal pull down device. Page 17 of 61 [+] Feedback CY7C66013C, CY7C66113C GPIO Configuration Port Every GPIO port is programmed as inputs with internal pull ups, outputs LOW or HIGH, or Hi-Z (floating, the pin is not driven internally). In addition, the interrupt polarity for each port is programmed. The Port Configuration bits (Table 11) and the Interrupt Enable bit (Table 9 on page 17 through Table 16 on page 19) determine the interrupt polarity of the port pins. Table 11. GPIO Configuration Register GPIO Configuration Bit # 7 6 5 4 3 2 1 ADDRESS 0x08 0 Bit Name Port 3 Config Bit 1 Port 3 Config Bit 0 Port 2 Config Bit 1 Port 2 Config Bit 0 Port 1 Config Bit 1 Port 1 Config Bit 0 Port 0 Config Bit 1 Port 0 Config Bit 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 As shown in Table 12, a positive polarity on an input pin represents a rising edge interrupt (LOW to HIGH), and a negative polarity on an input pin represents a falling edge interrupt (HIGH to LOW). The GPIO interrupt is generated when all of the following conditions are met: the Interrupt Enable bit of the associated Port Interrupt Enable Register is enabled, the GPIO Interrupt Enable bit of the Global Interrupt Enable Register (Table 31 on page 28) is enabled, the Interrupt Enable Sense (bit 2, Table 30 on page 27) is set, and the GPIO pin of the port sees an event matching the interrupt polarity. The driving state of each GPIO pin is determined by the value written to the pin’s Data Register (Table 7 on page 17 through Table 10 on page 17) and by its associated Port Configuration bits as shown in the GPIO Configuration Register (Table 9 on page 17). These ports are configured on a per port basis, so all pins in a given port are configured together. The possible port configurations are detailed in Table 12. As shown in this table, when a GPIO port is configured with CMOS outputs, interrupts from that port are disabled. During reset, all the bits in the GPIO Configuration Register are written with ‘0’ to select Hi-Z mode for all GPIO ports as the default configuration. Table 12. GPIO Port Output Control Truth Table and Interrupt Polarity Port Config Bit 1 Port Config Bit 0 Data Register Output Drive Strength Interrupt Enable Bit Output LOW 1 0 1 Resistive 1 – (Falling Edge) 1 0 0 Output LOW 0 Disabled 1 Output HIGH 1 Disabled 0 1 0 Output LOW 0 Disabled 1 Hi-Z 1 – (Falling Edge) 0 0 0 Output LOW 0 Disabled 1 Hi-Z 1 + (Rising Edge) Q1, Q2, and Q3 discussed here are the transistors referenced in Figure 6 on page 16. The available GPIO drive strength are: ■ Output HIGH Mode: The pin’s Data Register is set to 1 and the Port Configuration Bits[1:0] is set to ‘10’ In this mode, Q1 and Q3 are OFF. Q2 is ON. The GPIO is pulled up through Q2. The GPIO pin is capable of sourcing current. Document Number: 38-08024 Rev. *G Disabled Resistive Mode: The pin’s Data Register is set to 1 and the Port Configuration Bits[1:0] is set to ‘11’ Q2 and Q3 are OFF. Q1 is ON. The GPIO pin is pulled up with an internal 14 kresistor. In resistive mode, the pin may serve as an input. Reading the pin’s Data Register returns a logic HIGH if the pin is not driven LOW by an external source. Output LOW Mode: The pin’s Data Register is set to ‘0’ Writing ‘0’ to the pin’s Data Register puts the pin in output LOW mode, regardless of the contents of the Port Configuration Bits[1:0]. In this mode, Q1 and Q2 are OFF. Q3 is ON. The GPIO pin is driven LOW through Q3. ■ ■ 0 Interrupt Polarity 1 ■ Hi-Z Mode: The pin’s Data Register is set to1 and Port Configuration Bits[1:0] is set either ‘00’ or ‘01’ Q1, Q2, and Q3 are all OFF. The GPIO pin is not driven internally. In this mode, the pin may serve as an input. Reading the Port Data Register returns the actual logic value on the port pins. Page 18 of 61 [+] Feedback CY7C66013C, CY7C66113C GPIO Interrupt Enable Ports Each GPIO pin is individually enabled or disabled as an interrupt source. The Port 0–3 Interrupt Enable registers provide this feature with an interrupt enable bit for each GPIO pin. When HAPI mode is enabled the GPIO interrupts are blocked, including ports not used by HAPI, so GPIO pins are not used as interrupt sources. During a reset, GPIO interrupts are disabled by clearing all of the GPIO interrupt enable ports. Writing a ‘1’ to a GPIO Interrupt Enable bit enables GPIO interrupts from the corresponding input pin. All GPIO pins share a common interrupt, as discussed in GPIO and HAPI Interrupt on page 31. Table 13. Port 0 Interrupt Enable Port 0 Interrupt Enable Bit # 7 6 5 4 3 2 1 P0.6 Intr Enable P0.5 Intr Enable P0.4 Intr Enable P0.3 Intr Enable P0.2 Intr Enable P0.1 Intr Enable ADDRESS 0x04 0 Bit Name P0.7 Intr Enable P0.0 Intr Enable Read/Write W W W W W W W W Reset 0 0 0 0 0 0 0 0 Table 14. Port 1 Interrupt Enable Port 1 Interrupt Enable Bit # 7 6 5 4 3 2 1 ADDRESS 0x05 0 Bit Name P1.7 Intr Enable P1.6 Intr Enable P1.5 Intr Enable P1.4 Intr Enable P1.3 Intr Enable P1.2 Intr Enable P1.1 Intr Enable P1.0 Intr Enable Read/Write W W W W W W W W Reset 0 0 0 0 0 0 0 0 Table 15. Port 2 Interrupt Enable Port 2 Interrupt Enable Bit # 7 6 5 4 3 2 1 P2.6 Intr Enable P2.5 Intr Enable P2.4 Intr Enable P2.3 Intr Enable P2.2 Intr Enable P2.1 Intr Enable ADDRESS 0x06 0 Bit Name P2.7 Intr Enable P2.0 Intr Enable Read/Write W W W W W W W W Reset 0 0 0 0 0 0 0 0 3 2 1 Table 16. Port 3 Interrupt Enable Port 3 Interrupt Enable Bit # 7 6 5 4 ADDRESS 0x07 0 Bit Name Reserved P3.6 Intr Enable CY7C66113C only P3.5 Intr P3.4 Intr Enable Enable CY7C66113C only P3.3 Intr Enable P3.2 Intr Enable P3.1 Intr Enable P3.0 Intr Enable Read/Write W W W W W W W W Reset 0 0 0 0 0 0 0 0 Document Number: 38-08024 Rev. *G Page 19 of 61 [+] Feedback CY7C66013C, CY7C66113C DAC Port The CY7C66113C features a programmable sink current 8-bit port, which is also known as DAC port. Each of these port I/O pins have a programmable current sink. Writing a ‘1’ to a DAC I/O pin disables the output current sink (Isink DAC) and drives the I/O pin HIGH through an integrated 14 k resistor. When a ‘0’ is written to a DAC I/O pin, the Isink DAC is enabled and the pull up resistor is disabled. This causes the Isink DAC to sink current to drive the output LOW. Figure 7 shows a block diagram of the DAC port pin. Figure 7. Block Diagram of a DAC Pin VCC Data Out Latch Internal Data Bus Q1 Suspend (Bit 3 of Register 0xFF) 14 k DAC I/O Pin DAC Write 4 bits Isink Register Internal Buffer Isink DAC Interrupt Logic DAC Read Interrupt Enable Interrupt Polarity to Interrupt Controller The amount of sink current for the DAC I/O pin is programmable over 16 values based on the contents of the DAC Isink Register (Table 18 on page 21) for that output pin. DAC[1:0] are high current outputs that are programmable from 3.2 mA to 16 mA (typical). DAC[7:2] are low current outputs, programmable from 0.2 mA to 1.0 mA (typical). When the suspend bit in Processor Status and Control Register (Table 30 on page 27) is set, the Isink DAC block of the DAC circuitry is disabled. Special care should be taken when the CY7C66113C device is placed in the suspend. The DAC Port Data Register (Table 17) should normally be loaded with all ‘1’s (Table 30 on page 27) before setting the suspend bit. If any of the DAC bits are set to ‘0’ when the device is suspended, that DAC input floats. The floating pin could result in excessive current consumption by the device, unless an external load places the pin in a deterministic state. Table 17. DAC Port Data DAC Port Data Bit # 7 6 5 4 3 2 1 ADDRESS 0x30 0 Bit Name DAC[7] DAC[6] DAC[5] DAC[4] DAC[3] DAC[2] DAC[1] DAC[0] Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 1 1 1 1 1 1 1 1 Bit [1..0]: High Current Output 3.2 mA to 16 mA typical 1 = I/O pin is an output pulled HGH through the 14 k resistor. 0 = I/O pin is an input with an internal 14 k pull up resistor. Document Number: 38-08024 Rev. *G Bit [7..2]: Low Current Output 0.2 mA to 1 mA typical 1 = I/O pin is an output pulled HGH through the 14 k resistor. 0 = I/O pin is an input with an internal 14 k pull up resistor. Page 20 of 61 [+] Feedback CY7C66013C, CY7C66113C DAC Isink Registers Each DAC I/O pin has an associated DAC Isink register to program the output sink current when the output is driven LOW. The first Isink register (0x38) controls the current for DAC[0], the second (0x39) for DAC[1], and so on until the Isink register at 0x3F, controls the current to DAC[7]. Table 18. DAC Sink Register DAC Sink Register Bit # 7 Bit Name Reserved 5 4 3 2 1 Reserved Reserved Reserved Isink[3] Isink[2] Isink[1] Isink[0] W W W W 0 0 0 0 Read/Write Reset - ADDRESS 0x38 –0x3F 0 6 - - - Bit [3..0]: Isink [x] (x= 0..3) Writing all ‘0’s to the Isink register causes 1/5 of the max current to flow through the DAC I/O pin. Writing all ‘1’s to the Isink register provides the maximum current flow through the pin. The other 14 states of the DAC sink current are evenly spaced between these two values. Bit [7..4]: Reserved DAC Port Interrupts A DAC port interrupt is enabled or disabled for each pin individually. The DAC Port Interrupt Enable register provides this feature with an interrupt enable bit for each DAC I/O pin. All of the DAC Port Interrupt Enable register bits are cleared to ‘0’ during a reset. All DAC pins share a common interrupt, as explained in DAC Interrupt on page 31. Table 19. DAC Port Interrupt Enable DAC Port Interrupt Bit # 7 ADDRESS 0x31 0 6 5 4 3 2 1 Enable Bit 5 Enable Bit 4 Enable Bit 3 Enable Bit 2 Enable Bit 1 Bit Name Enable Bit 7 Enable Bit 6 Read/Write W W W W W W W W Reset 0 0 0 0 0 0 0 0 Bit [7..0]: Enable bit x (x= 0..7) 1 = Enables interrupts from the corresponding bit position; 0 = Disables interrupts from the corresponding bit position As an additional benefit, the interrupt polarity for each DAC pin is programmable with the DAC Port Interrupt Polarity register. Writing a ‘0’ to a bit selects negative polarity (falling edge) that Enable Bit 0 causes an interrupt (if enabled) if a falling edge transition occurs on the corresponding input pin. Writing a ‘1’ to a bit in this register selects positive polarity (rising edge) that causes an interrupt (if enabled) if a rising edge transition occurs on the corresponding input pin. All of the DAC Port Interrupt Polarity register bits are cleared during a reset. Table 20. DAC Port Interrupt Polarity DAC I/O Interrupt Polarity Bit # 7 6 5 4 3 2 1 ADDRESS 0x32 0 Bit Name Polarity Bit 7 Polarity Bit 6 Polarity Bit 5 Polarity Bit 4 Polarity Bit 3 Polarity Bit 2 Polarity Bit 1 Polarity Bit 0 Read/Write W W W W W W W W Reset 0 0 0 0 0 0 0 0 Bit [7..0]: Polarity bit x (x= 0..7) 1= Selects positive polarity (rising edge) that causes an interrupt (if enabled); 0 = Selects negative polarity (falling edge) that causes an interrupt (if enabled). Document Number: 38-08024 Rev. *G Page 21 of 61 [+] Feedback CY7C66013C, CY7C66113C 12-bit Free-Running Timer The 12-bit timer operates with a 1 s tick, provides two interrupts (128 s and 1.024 ms) and allows the firmware to directly time events that are up to 4 ms in duration. The lower eight bits of the timer is read directly by the firmware. Reading the lower 8 bits latches the upper four bits into a temporary register. When the firmware reads the upper four bits of the timer, it is actually reading the count stored in the temporary register. The effect of this is to ensure a stable 12-bit timer value is read, even when the two reads are separated in time. Table 21. Timer LSB Register Timer LSB Bit # ADDRESS 0x24 0 7 6 5 4 3 2 1 Bit Name Timer Bit 7 Timer Bit 6 Timer Bit 5 Timer Bit 4 Timer Bit 3 Timer Bit 2 Timer Bit 1 Timer Bit 0 Read/Write R R R R R R R R Reset 0 0 0 0 0 0 0 0 Bit [7:0]: Timer lower eight bits Table 22. Timer MSB Register Timer MSB Bit # ADDRESS 0x25 0 7 6 5 4 3 2 1 Bit Name Reserved Reserved Reserved Reserved Timer Bit 11 Timer Bit 10 Timer Bit 9 Read/Write - - - - R R R R Reset 0 0 0 0 0 0 0 0 Timer Bit 8 Bit [3:0]: Timer higher nibble Bit [7:4]: Reserved Figure 8. Timer Block Diagram 1.024 ms interrupt 128 s interrupt 11 10 9 L 8 7 6 5 4 3 2 1 0 1 MHz clock L2 L1 L0 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 8 Document Number: 38-08024 Rev. *G To Timer Registers Page 22 of 61 [+] Feedback CY7C66013C, CY7C66113C I2C and HAPI Configuration Register Internal hardware supports communication with external devices through two interfaces: a two wire I2C compatible, and a HAPI for 1, 2, or 3 byte transfers. The I2C compatible and HAPI functions, share a common configuration register (see Table 23)[3]. All bits of this register are cleared on reset. Table 23. HAPI/I2C Configuration Register I2C Configuration Bit # 7 Bit Name I2C Position ADDRESS 0x09 0 6 5 4 3 2 1 Reserved LEMPTY Polarity DRDY Polarity Latch Empty Data Ready HAPI Port Width Bit 1 HAPI Port Width Bit 0 Read/Write R/W - R/W R/W R R R/W R/W Reset 0 0 0 0 0 0 0 0 Bits [7,1:0] of the HAPI and I2C Configuration Register control the pin out configuration of the HAPI and I2C compatible interfaces. Bits [5:2] are used in HAPI mode only, and are described in Hardware Assisted Parallel Interface (HAPI) on page 26. Table 24 shows the HAPI port configurations, and Table 25 shows I2C pin location configuration options. These I2C compatible options exist due to pin limitations in certain packages, and to allow simultaneous HAPI and I2C compatible operation. HAPI operation is enabled whenever either HAPI Port Width Bit (Bit 1 or 0) is non zero. This affects GPIO operation as described in Hardware Assisted Parallel Interface (HAPI) on page 26. The I2C compatible interface must be separately enabled. Table 24. HAPI Port Configuration Port Width (Bit 0 and 1, Figure 23) HAPI Port Width 11 24 Bits: P3[7:0], P1[7:0], P0[7:0] 10 16 Bits: P1[7:0], P0[7:0] 01 8 Bits: P0[7:0] 00 No HAPI Interface Table 25. I2C Port Configuration I2C Position (Bit 7, Table 23 on page 23) I2C Port Width (Bit 1, Table 23 on page 23) I2C Position Don’t Care 1 I2C on P2[1:0], 0:SCL, 1:SDA 0 0 I2C on P1[1:0], 0:SCL, 1:SDA 1 0 I2C on P2[1:0], 0:SCL, 1:SDA I2C Compatible Controller The I2C compatible block provides a versatile two wire communication with external devices, supporting master, slave, and multi-master modes of operation. The I2C compatible block functions by handling the low level signaling in hardware, and issuing interrupts as needed to allow firmware to take appropriate action during transactions. While waiting for firmware response, the hardware keeps the I2C compatible bus idle if necessary. The I2C compatible interface generates an interrupt to the microcontroller at the end of each received or transmitted byte, when a stop bit is detected by the slave when in receive mode, or when arbitration is lost. Details of the interrupt responses are given in Hardware Assisted Parallel Interface (HAPI) on page 26. The I2C compatible interface consists of two registers, an I2C Data Register (Table 14 on page 19) and an I2C Status and Control Register (Table 27 on page 24). The Data Register is implemented as separate read and write registers. Generally, the I2C Status and Control Register are only monitored after the I2C interrupt, as all bits are valid at that time. Polling this register at other times could read misleading bit status if a transaction is underway. The I2C SCL clock is connected to bit 0 of GPIO port 1 or GPIO port 2, and the I2C SDA data is connected to bit 1 of GPIO port 1 or GPIO port 2. Refer to I2C and HAPI Configuration Register on page 23 for the bit definitions and functionality of the HAPI and I2C Configuration Register, which is used to set the locations of the configurable I2C pins. When the I2C compatible functionality is enabled by setting bit 0 of the I2C Status & Control Register, the two LSB ([1:0]) of the corresponding GPIO port is placed in Open Drain mode, regardless of the settings of the GPIO Configuration Register. The electrical characteristics of the I2C compatible interface is the same as that of GPIO ports 1 and 2. Note that the IOL (max) is 2 mA at VOL = 2.0 V for ports 1 and 2. Note 3. I2C compatible function must be separately enabled. Document Number: 38-08024 Rev. *G Page 23 of 61 [+] Feedback CY7C66013C, CY7C66113C All control of the I2C clock and data lines is performed by the I2C compatible block. Table 26. I2C Data Register I2C Data Bit # ADDRESS 0x29 0 7 6 5 4 3 2 1 Bit Name I2C Data 7 I2C Data 6 I2C Data 5 I2C Data 4 I2C Data 3 I2C Data 2 I2C Data 1 I2C Data 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset X X X X X X X X I2 Bits [7..0]: C Data Contains 8-bit data on the I2C Bus. Table 27. I2C Status and Control Register I2C Status and Control Bit # 7 Bit Name 6 5 ADDRESS 0x28 0 4 3 2 1 MSTR Mode Continue/Bu Xmit Mode sy ACK Addr ARB Lost/Restart Received Stop I2C Enable Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 The I2C Status and Control register bits are defined in Table 28, with a more detailed description following. Table 28. I2C Status and Control Register Bit Definitions Bit Name Description 0 I2C Enable When set to ‘1’, the I2C compatible function is enabled. When cleared, I2C GPIO pins operate normally. 1 Received Stop Reads 1 only in slave receive mode, when I2C Stop bit detected (unless firmware did not ACK the last transaction). 2 ARB Lost/Restart Reads 1 to indicate master has lost arbitration. Reads 0 otherwise. Write to 1 in master mode to perform a restart sequence (also set Continue bit). 3 Addr Reads 1 during first byte after start/restart in slave mode, or if master loses arbitration. Reads 0 otherwise. This bit should always be written as 0. 4 ACK In receive mode, write 1 to generate ACK, 0 for no ACK. In transmit mode, reads 1 if ACK was received, 0 if no ACK received. 5 Xmit Mode Write to 1 for transmit mode, 0 for receive mode. 6 Continue/Busy Write 1 to indicate ready for next transaction. Reads 1 when I2C compatible block is busy with a transaction, 0 when transaction is complete. 7 MSTR Mode Write to 1 for master mode, 0 for slave mode. This bit is cleared if master loses arbitration. Clearing from 1 to 0 generates Stop bit. Document Number: 38-08024 Rev. *G Page 24 of 61 [+] Feedback CY7C66013C, CY7C66113C Bit 4: ACK Bit 7: MSTR Mode I2 Setting this bit to 1 causes the C compatible block to initiate a master mode transaction by sending a start bit and transmitting the first data byte from the data register (this typically holds the target address and R/W bit). Subsequent bytes are initiated by setting the Continue bit, as described later in this section. This bit is set or cleared by firmware during receive operation to indicate if the hardware should generate an ACK signal on the I2C compatible bus. Writing a 1 to this bit generates an ACK (SDA LOW) on the I2C compatible bus at the ACK bit time. During transmits (Xmit Mode = 1), this bit should be cleared. Clearing this bit (set to 0) causes the GPIO pins to operate normally. In master mode, the I2C compatible block generates the clock (SCK), and drives the data line as required depending on transmit or receive state. The I2C compatible block performs any required arbitration and clock synchronization. IN the event of a loss of arbitration, this MSTR bit is cleared, the ARB Lost bit is set, and an interrupt is generated by the microcontroller. If the chip is the target of an external master that wins arbitration, then the interrupt is held off until the transaction from the external master is completed. Bit 3: Addr When MSTR Mode is cleared from 1 to 0 by a firmware write, an I2C Stop bit is generated. Bit 6: Continue/Busy This bit is written by the firmware to indicate that the firmware is ready for the next byte transaction to begin. In other words, the bit has responded to an interrupt request and has completed the required update or read of the data register. During a read this bit indicates if the hardware is busy and is locking out additional writes to the I2C Status and Control register. This locking allows the hardware to complete certain operations that may require an extended period of time. Following an I2C interrupt, the I2C compatible block does not return to the Busy state until firmware sets the Continue bit. This allows the firmware to make one control register write without the need to check the Busy bit. Bit 5: Xmit Mode This bit is set by firmware to enter transmit mode and perform a data transmit in master or slave mode. Clearing this bit sets the part in receive mode. Firmware generally determines the value of this bit from the R/W bit associated with the I2C address packet. The Xmit Mode bit state is ignored when initially writing the MSTR Mode or the Restart bits, as these cases always cause transmit mode for the first byte. Document Number: 38-08024 Rev. *G This bit is set by the I2C compatible block during the first byte of a slave receive transaction, after an I2C start or restart. The Addr bit is cleared when the firmware sets the Continue bit. This bit allows the firmware to recognize when the master has lost arbitration, and in slave mode it allows the firmware to recognize that a start or restart has occurred. Bit 2: ARB Lost/Restart This bit is valid as a status bit (ARB Lost) after master mode transactions. In master mode, set this bit (along with the Continue and MSTR Mode bits) to perform an I2C restart sequence. The I2C target address for the restart must be written to the data register before setting the Continue bit. To prevent false ARB Lost signals, the Restart bit is cleared by hardware during the restart sequence. Bit 1: Receive Stop This bit is set when the slave is in receive mode and detects a stop bit on the bus. The Receive Stop bit is not set if the firmware terminates the I2C transaction by not acknowledging the previous byte transmitted on the I2C compatible bus. For example, in receive mode if firmware sets the Continue bit and clears the ACK bit. Bit 0: I2C Enable Set this bit to override GPIO definition with I2C compatible function on the two I2C compatible pins. When this bit is cleared, these pins are free to function as GPIOs. In I2C compatible mode, the two pins operate in open drain mode, independent of the GPIO configuration setting. Page 25 of 61 [+] Feedback CY7C66013C, CY7C66113C Hardware Assisted Parallel Interface (HAPI) The CY7C66x13C processor provides a hardware assisted parallel interface for bus widths of 8, 16, or 24 bits, to accommodate data transfer with an external microcontroller or similar device. Control bits for selecting the byte width are in the HAPI and I2C Configuration Register (Table 23 on page 23), bits 1 and 0. Signals are provided on Port 2 to control the HAPI interface. Table 29 describes these signals and the HAPI control bits in the HAPI and I2C Configuration Register. Enabling HAPI causes the GPIO setting in the GPIO Configuration Register (Table 9 on page 17) to be overridden. The Port 2 output pins are in CMOS output mode and Port 2 input pins are in input mode (open drain mode with Q3 OFF in Figure 6 on page 16). Table 29. Port 2 Pin and HAPI Configuration Bit Definitions Pin Name Direction Description (Port 2 Pin) P2[2] LatEmptyPin Out Ready for more input data from external interface. P2[3] DReadyPin Out Output data ready for external interface. P2[4] STB In Strobe signal for latching incoming data. P2[5] OE In Output Enable, causes chip to output data. P2[6] CS In Chip Select (Gates STB and OE). Bit Name R/W R Description (HAPI and I2C Configuration Register) Asserted after firmware writes data to Port 0, until OE driven LOW. 2 Data Ready 3 Latch Empty R Asserted after firmware reads data from Port 0, until STB driven LOW. 4 DRDY Polarity R/W Determines polarity of Data Ready bit and DReadyPin: If 0, Data Ready is active LOW, DReadyPin is active HIGH. If 1, Data Ready is active HIGH, DReadyPin is active LOW. 5 LEMPTY Polarity R/W Determines polarity of Latch Empty bit and LatEmptyPin: If 0, Latch Empty is active LOW, LatEmptyPin is active HIGH. If 1, Latch Empty is active HIGH, LatEmptyPin is active LOW. HAPI Read by External Device from CY7C66x13C HAPI Write by External Device to CY7C66x13C In this case (see Figure 14 on page 53), firmware writes data to the GPIO ports. If 16-bit or 24-bit transfers are being made, Port 0 is written last, because writes to Port 0 asserts the Data Ready bit and the DReadyPin to signal the external device that data is available. In this case (see Figure 16 on page 55), the external device drives the STB and CS pins active (LOW) when it drives new data onto the port pins. When this happens, the internal latches become full, which causes the Latch Empty bit to be deasserted. When STB is returned HIGH (inactive), the HAPI and GPIO interrupt is generated. Firmware then reads the parallel ports to empty the HAPI latches. If 16-bit or 24-bit transfers are being made, Port 0 should be read last because reads from Port 0 assert the Latch Empty bit and the LatEmptyPin to signal the external device for more data. The external device then drives the OE and CS pins active (LOW), which causes the HAPI data to be output on the port pins. When OE is returned HIGH (inactive), the HAPI/GPIO interrupt is generated. At that point, firmware is reload the HAPI latches for the next output, again writing Port 0 last. The Data Ready bit reads the opposite state from the external DReadyPin on pin P2[3]. If the DRDY Polarity bit is 0, DReadyPin is active HIGH, and the Data Ready bit is active LOW. Document Number: 38-08024 Rev. *G The Latch Empty bit reads the opposite state from the external LatEmptyPin on pin P2[2]. If the LEMPTY Polarity bit is 0, LatEmptyPin is active HIGH, and the Latch Empty bit is active LOW. Page 26 of 61 [+] Feedback CY7C66013C, CY7C66113C Processor Status and Control Register Table 30. Processor Status and Control Register Processor Status and Control Bit # 7 6 Bit Name IRQ Pending Watchdog Reset ADDRESS 0xFF 0 5 4 3 2 1 USB Bus Reset Interrupt Power On Reset Suspend Interrupt Enable Sense Reserved Run Read/Write R R/W R/W R/W R/W R R/W R/W Reset 0 0 0 1 0 0 0 1 Bit 0: Run Bit 5: USB Bus Reset Interrupt This bit is manipulated by the HALT instruction. When Halt is executed, all the bits of the Processor Status and Control Register are cleared to 0. Since the run bit is cleared, the processor stops at the end of the current instruction. The processor remains halted until an appropriate reset occurs (power on or Watchdog). This bit should normally be written as a ‘1.’ The USB Bus Reset Interrupt bit is set when the USB Bus Reset is detected on receiving a USB Bus Reset signal on the upstream port. The USB Bus Reset signal is a single ended zero (SE0) that lasts from 12 to 16 s. An SE0 is defined as the condition in which both the D+ line and the D– line are LOW at the same time. Bit 6: WDR Bit 1 is reserved and must be written as a zero. The WDR is set during a reset initiated by the WDT. This indicates the WDT went for more than tWATCH (8 ms minimum) between Watchdog clears. This occurs with a POR event. Bit 2: Interrupt Enable Sense Bit 7: IRQ Pending This bit indicates whether interrupts are enabled or disabled. Firmware has no direct control over this bit as writing a zero or one to this bit position has no effect on interrupts. A ‘0’ indicates that interrupts are masked off and a ‘1’ indicates that the interrupts are enabled. This bit is further gated with the bit settings of the Global Interrupt Enable Register (Table 31 on page 28) and USB End Point Interrupt Enable Register (Table 32 on page 28). Instructions DI, EI, and RETI manipulate the state of this bit. The IRQ pending, when set, indicates that one or more of the interrupts is recognized as active. An interrupt remains pending until its interrupt enable bit is set (Table 31 on page 28, Table 32 on page 28) and interrupts are globally enabled. At that point, the internal interrupt handling sequence clears this bit until another interrupt is detected as pending. Bit 1: Reserved Bit 3: Suspend Writing a ‘1’ to the Suspend bit halts the processor and cause the microcontroller to enter the suspend mode that significantly reduces power consumption. A pending, enabled interrupt or USB bus activity causes the device to come out of suspend. After coming out of suspend, the device resumes firmware execution at the instruction following the IOWR which put the part into suspend. An IOWR attempting to put the part into suspend is ignored if USB bus activity is present. See Suspend Mode on page 16 for more details on suspend mode operation. Bit 4: Power on Reset The POR is set to ‘1’ during a power on reset. The firmware checks bits 4 and 6 in the reset handler to determine whether a reset was caused by a power on condition or a Watchdog timeout. A POR event may be followed by a WDR before firmware begins executing, as explained here. Document Number: 38-08024 Rev. *G During power up, the Processor Status and Control Register is set to 00010001, which indicates a POR (bit 4 set) has occurred and no interrupts are pending (bit 7 clear). During the 96 ms suspend at start up (explained in Power on Reset on page 15), a WDR also occurs unless this suspend is aborted by an upstream SE0 before 8 ms. If a WDR occurs during the power up suspend interval, firmware reads 01010001 from the Status and Control Register after power up. Normally, the POR bit should be cleared so a subsequent WDR is clearly identified. If an upstream bus reset is received before firmware examines this register, the Bus Reset bit may also be set. During a WDR, the Processor Status and Control Register is set to 01XX0001, which indicates a WDR (bit 6 set) has occurred and no interrupts are pending (bit 7 clear). The WDR does not effect the state of the POR and the Bus Reset Interrupt bits. Page 27 of 61 [+] Feedback CY7C66013C, CY7C66113C Interrupts Interrupts are generated by the GPIO and DAC pins, the internal timers, I2C compatible or HAPI operation, the internal USB hub, or on various USB traffic conditions. All interrupts are maskable by the Global Interrupt Enable Register and the USB End Point Interrupt Enable Register. Writing a ‘1’ to a bit position enables the interrupt associated with that bit position. Table 31. Global Interrupt Enable Register Global Interrupt Enable Register Bit # 7 6 Bit Name Reserved I2C Read/Write Reset ADDRESS 0X20 5 4 3 2 1 0 Interrupt GPIO Enable Interrupt Enable DAC Interrupt Enable USB Hub Interrupt Enable 1.024 ms Interrupt Enable 128 s Interrupt Enable USB Bus RST Interrupt Enable - R/W R/W R/W R/W R/W R/W R/W - 0 0 0 0 0 0 0 Bit 4: DAC Interrupt Enable Bit 0: USB Bus RST Interrupt Enable 1 = Enable DAC Interrupt; 0 = Disable DAC interrupt. 1 = Enable Interrupt on a USB Bus Reset; 0 = Disable interrupt on a USB Bus Reset (Refer to USB Bus Reset Interrupt on page 30). Bit 5: GPIO Interrupt Enable 1 = Enable Interrupt on falling and rising edge on any GPIO; 0 = Disable Interrupt on falling and rising edge on any GPIO. (Refer to sections GPIO and HAPI Interrupt on page 31, GPIO Configuration Port on page 18, and GPIO Interrupt Enable Ports on page 19.) Bit 1: 128 s Interrupt Enable 1 = Enable Timer interrupt every 128 s; 0 = Disable Timer Interrupt for every 128 s. Bit 2: 1.024 ms Interrupt Enable Bit 6: I2C Interrupt Enable 1= Enable Timer interrupt every 1.024 ms; 0 = Disable Timer Interrupt every 1.024 ms. 1 = Enable Interrupt on I2C related activity; 0 = Disable I2C related activity interrupt. (Refer to I2C Interrupt on page 32.) Bit 3: USB Hub Interrupt Enable 1 = Enable Interrupt on a Hub status change; 0 = Disable interrupt due to hub status change. (Refer to USB Hub Interrupt on page 30.) Bit 7: Reserved. Table 32. USB Endpoint Interrupt Enable Register USB Endpoint Interrupt Enable ADDRESS 0X21 Bit # 7 6 5 4 3 2 1 0 Bit Name Reserved Reserved Reserved EPB1 Interrupt Enable EPB0 Interrupt Enable EPA2 Interrupt Enable EPA1 Interrupt Enable EPA0 Interrupt Enable Read/Write - - - R/W R/W R/W R/W R/W Reset - - - 0 0 0 0 0 Bit 0: EPA0 Interrupt Enable 1 = Enable Interrupt on data activity through endpoint A0; 0 = Disable Interrupt on data activity through endpoint A0. Bit 1: EPA1 Interrupt Enable 1 = Enable Interrupt on data activity through endpoint A1; 0 = Disable Interrupt on data activity through endpoint A1. Bit 2: EPA2 Interrupt Enable 1 = Enable Interrupt on data activity through endpoint A2; 0 = Disable Interrupt on data activity through endpoint A2. Bit 3: EPB0 Interrupt Enable 1 = Enable Interrupt on data activity through endpoint B0; 0 = Disable Interrupt on data activity through endpoint B0. Document Number: 38-08024 Rev. *G Bit 4: EPB1 Interrupt Enable 1 = Enable Interrupt on data activity through endpoint B1; 0 = Disable Interrupt on data activity through endpoint B1. Bit [7..5]: Reserved During a reset, the contents the Global Interrupt Enable Register and USB End Point Interrupt Enable Register are cleared, effectively, disabling all interrupts. The interrupt controller contains a separate flip flop for each interrupt. See Figure 9 on page 29 for the logic block diagram of the interrupt controller. When an interrupt is generated, it is first registered as a pending interrupt. It stays pending until it is serviced or a reset occurs. A pending interrupt only generates an interrupt request if it is enabled by the corresponding bit in the interrupt enable registers. The highest priority interrupt request Page 28 of 61 [+] Feedback CY7C66013C, CY7C66113C is serviced following the completion of the currently executing instruction. When servicing an interrupt, the hardware does the following: 1. Disables all interrupts by clearing the Global Interrupt Enable bit in the CPU (the state of this bit is read at Bit 2 of the Processor Status and Control Register, Table 30 on page 27). 2. Clears the flip flop of the current interrupt. 3. Generates an automatic CALL instruction to the ROM address associated with the interrupt being serviced (that is, the Interrupt Vector). The instruction in the interrupt table is typically a JMP instruction to the address of the Interrupt Service Routine (ISR). The user re-enables interrupts in the interrupt service routine by executing an EI instruction. Interrupts are nested to a level limited only by the available stack space. The Program Counter value and the Carry and Zero flags (CF, ZF) are stored onto the Program Stack by the automatic CALL instruction generated as part of the interrupt acknowledge process. The user firmware is responsible for ensuring that the processor state is preserved and restored during an interrupt. The PUSH A instruction should typically be used as the first command in the ISR to save the accumulator value and the POP A instruction should be used to restore the accumulator value just before the RETI instruction. The program counter CF and ZF are restored and interrupts are enabled when the RETI instruction is executed. The DI and EI instructions are used to disable and enable interrupts, respectively. These instructions affect only the Global Interrupt Enable bit of the CPU. If desired, EI is used to re-enable interrupts while inside an ISR, instead of waiting for the RETI that exists the ISR. While the global interrupt enable bit is cleared, the presence of a pending interrupt is detected by examining the IRQ Sense bit (Bit 7 in the Processor Status and Control Register). Interrupt Vectors The Interrupt Vectors supported by the USB Controller are listed in Table 33 on page 30. The lowest numbered interrupt (USB Bus Reset interrupt) has the highest priority, and the highest numbered interrupt (I2C interrupt) has the lowest priority. Figure 9. Interrupt Controller Function Diagram CLR 1 D USB Reset Int Q CLK CLR Q D 1 AddrA ENP2 Int CLK Enable [0] (Reg 0x20) Enable [2] (Reg 0x21) USB Reset Clear Interrupt Vector USB Reset IRQ 128-s CLR 128-s IRQ 1-ms CLR 1-ms IRQ IRQout AddrA EP0 CLR AddrA EP0 IRQ AddrA EP1 CLR AddrA EP1 IRQ AddrA EP2 CLR AddrA EP2 IRQ AddrB EP0 CLR AddrB EP0 IRQ AddrB EP1 CLR AddrB EP1 IRQ Hub CLR Hub IRQ DAC CLR DAC IRQ To CPU CPU IRQ Sense IRQ Global Interrupt Enable Bit CLR Int Enable Sense Controlled by DI, EI, and RETI Instructions Interrupt Acknowledge GPIO/HAPI CLR GPIO/HAPI IRQ I2C CLR CLR 1 I2C Int D CLK Q Enable [6] (Reg 0x20) Document Number: 38-08024 Rev. *G I2C IRQ Interrupt Priority Encoder Page 29 of 61 [+] Feedback CY7C66013C, CY7C66113C Although Reset is not an interrupt, the first instruction executed after a reset is at PROM address 0x0000h—which corresponds to the first entry in the Interrupt Vector Table. Because the JMP instruction is two bytes long, the interrupt vectors occupy two bytes. Table 33. Interrupt Vector Assignments Interrupt Vector Number Not Applicable 1 2 3 4 5 6 7 8 9 10 11 12 ROM Address 0x0000 0x0002 0x0004 0x0006 0x0008 0x000A 0x000C 0x000E 0x0010 0x0012 0x0014 0x0016 0x0018 Interrupt Latency Interrupt latency is calculated from the following equation: Interrupt latency = (Number of clock cycles remaining in the current instruction) + (10 clock cycles for the CALL instruction) + (5 clock cycles for the JMP instruction). For example, if a five clock cycle instruction such as JC is being executed when an interrupt occurs, the first instruction of the Interrupt Service Routine executes a minimum of 16 clocks (1+10+5) or a maximum of 20 clocks (5+10+5) after the interrupt is issued. For a 12 MHz internal clock (6 MHz crystal), 20 clock periods is 20/12 MHz = 1.667 s. USB Bus Reset Interrupt The USB Controller recognizes a USB Reset when a Single Ended Zero (SE0) condition persists on the upstream USB port for 12–16 s. SE0 is defined as the condition in which both the D+ line and the D– line are LOW. A USB Bus Reset may be recognized for an SE0 as short as 12 s, but is always recognized for an SE0 longer than 16 s. When a USB Bus Reset is detected, bit 5 of the Processor Status and Control Register (Table 30 on page 27) is set to record this event. In addition, the controller clears the following registers: SIE Section: USB Device Address Registers (0x10, 0x40) Hub Section: Hub Ports Connect Status (0x48) Hub Ports Enable (0x49) Hub Ports Speed (0x4A) Function Execution after Reset begins here USB Bus Reset interrupt 128 s timer interrupt 1.024 ms timer interrupt USB Address A Endpoint 0 interrupt USB Address A Endpoint 1 interrupt USB Address A Endpoint 2 interrupt USB Address B Endpoint 0 interrupt USB Address B Endpoint 1 interrupt USB Hub interrupt DAC interrupt GPIO and HAPI interrupt I2C interrupt A USB Bus Reset Interrupt is generated at the end of the USB Bus Reset condition when the SE0 state is deasserted. If the USB reset occurs during the start up delay following a POR, the delay is aborted as described in Power on Reset on page 15. Timer Interrupt There are two periodic timer interrupts: the 128 s interrupt and the 1.024 ms interrupt. The user should disable both timer interrupts before going into the suspend mode to avoid possible conflicts between servicing the timer interrupts first or the suspend request first. USB Endpoint Interrupts There are five USB endpoint interrupts, one per endpoint. A USB endpoint interrupt is generated after the USB host writes to a USB endpoint FIFO or after the USB controller sends a packet to the USB host. The interrupt is generated on the last packet of the transaction. For example, on the host’s ACK during an IN, or on the device ACK during on OUT. If no ACK is received during an IN transaction, no interrupt is generated. USB Hub Interrupt A USB hub interrupt is generated by the hardware after a connect/disconnect change, babble, or a resume event is detected by the USB repeater hardware. The babble and resume events are additionally gated by the corresponding bits of the Hub Port Enable Register (Table 36 on page 34). The connect and disconnect event on a port does not generate an interrupt if the SIE does not drive the port (that is, the port is being forced). Hub Ports Suspend (0x4D) Hub Ports Resume Status (0x4E) Hub Ports SE0 Status (0x4F) Hub Ports Data (0x50) Hub Downstream Force (0x51). Document Number: 38-08024 Rev. *G Page 30 of 61 [+] Feedback CY7C66013C, CY7C66113C DAC Interrupt GPIO and HAPI Interrupt Each DAC I/O pin generates an interrupt, if enabled. The interrupt polarity for each DAC I/O pin is programmable. A positive polarity is a rising edge input while a negative polarity is a falling edge input. All of the DAC pins share a single interrupt vector, which means the firmware needs to read the DAC port to determine which pin or pins caused an interrupt. Each of the GPIO pins generates an interrupt, if enabled. The interrupt polarity is programmed for each GPIO port as part of the GPIO configuration. All of the GPIO pins share a single interrupt vector, which means the firmware needs to read the GPIO ports with enabled interrupts to determine which pin or pins caused an interrupt. A block diagram of the GPIO interrupt logic is shown in Figure 10. Refer to GPIO Configuration Port on page 18 and GPIO Interrupt Enable Ports on page 19 for more information about setting GPIO interrupt polarity and enabling individual GPIO interrupts. If one DAC pin has triggered an interrupt, no other DAC pins causes a DAC interrupt until that pin has returned to its inactive (non trigger) state or the corresponding interrupt enable bit is cleared. The USB Controller does not assign interrupt priority to different DAC pins and the DAC Interrupt Enable Register is not cleared during the interrupt acknowledge process. Figure 10. GPIO Interrupt Structure Port Configuration Register GPIO Pin 1 = Enable 0 = Disable OR Gate (1 input per GPIO pin) M U X GPIO Interrupt Flip Flop 1 D Q CLR Interrupt Priority Encoder IRQout Interrupt Vector Port Interrupt Enable Register IRA 1 = Enable 0 = Disable Global GPIO Interrupt Enable (Bit 5, Register 0x20) If one port pin has triggered an interrupt, no other port pins cause a GPIO interrupt until that port pin has returned to its inactive (non trigger) state or its corresponding port interrupt enable bit is cleared. The USB Controller does not assign interrupt priority to different port pins and the Port Interrupt Enable Registers are not cleared during the interrupt acknowledge process. When HAPI is enabled, the HAPI logic takes over the interrupt vector and blocks any interrupt from the GPIO bits, including ports and bits not used by HAPI. Operation of the HAPI interrupt Document Number: 38-08024 Rev. *G is independent of the GPIO specific bit interrupt enables, and is enabled or disabled only by bit 5 of the Global Interrupt Enable Register (0x20) when HAPI is enabled. The settings of the GPIO bit interrupt enables on ports and bits not used by HAPI still effect the CMOS mode operation of those ports and bits. The effect of modifying the interrupt bits while the Port Config bits are set to ‘10’ is shown in Table 12 on page 18. The events that generate HAPI interrupts are described in Hardware Assisted Parallel Interface (HAPI) on page 26. Page 31 of 61 [+] Feedback CY7C66013C, CY7C66113C I2C Interrupt The I2C interrupt occurs after various events on the I2C compatible bus to signal the need for firmware interaction. This generally involves reading the I2C Status and Control Register (Table 27 on page 24) to determine the cause of the interrupt, loading and reading the I2C Data Register as appropriate, and finally writing the Processor Status and Control Register (Table 30 on page 27) to initiate the subsequent transaction. The interrupt indicates that status bits are stable and it is safe to read and write the I2C registers. When enabled, the I2C compatible state machines generate interrupts on completion of the following conditions. The referenced bits are in the I2C Status and Control Register. USB Overview The USB hardware includes a USB Hub repeater with one upstream and four downstream ports. The USB Hub repeater interfaces to the microcontroller through a full speed Serial Interface Engine. An external series resistor of Rext must be placed in series with all upstream and downstream USB outputs to meet the USB driver requirements of the USB specification. The CY7C66x13C microcontroller provides the functionality of a compound device consisting of a USB hub and permanently attached functions. USB Serial Interface Engine The SIE allows the CY7C66x13C microcontroller to communicate with the USB host through the USB repeater portion of the hub. The SIE simplifies the interface between the microcontroller and USB by incorporating hardware that handles the following USB bus activity independently of the microcontroller: ■ In slave receive mode, after the slave receives a byte of data: The Addr bit is set, if this is the first byte since a start or restart signal was sent by the external master. Firmware must read or write the data register as necessary, then set the ACK, Xmit MODE, and Continue/Busy bits appropriately for the next byte. ■ In slave receive mode, after a stop bit is detected: The Received Stop bit is set, if the stop bit follows a slave receive transaction where the ACK bit was cleared to 0, no stop bit detection occurs. ■ Bit stuffing and unstuffing ■ Checksum generation and checking ■ ACK/NAK/STALL In slave transmit mode, after the slave transmits a byte of data: The ACK bit indicates if the master that requested the byte acknowledged the byte. If more bytes are to be sent, firmware writes the next byte into the Data Register and then sets the Xmit MODE and Continue/Busy bits as required. ■ Token type identification ■ Address checking. ■ ■ ■ ■ In master transmit mode, after the master sends a byte of data. Firmware should load the Data Register if necessary, and set the Xmit MODE, MSTR MODE, and Continue/Busy bits appropriately. Clearing the MSTR MODE bit issues a stop signal to the I2C compatible bus and return to the idle state. In master receive mode, after the master receives a byte of data: Firmware should read the data and set the ACK and Continue/Busy bits appropriately for the next byte. Clearing the MSTR MODE bit at the same time causes the master state machine to issue a stop signal to the I2C compatible bus and leave the I2C compatible hardware in the idle state. When the master loses arbitration: This condition clears the MSTR MODE bit and sets the ARB Lost/Restart bit immediately and then waits for a stop signal on the I2C compatible bus to generate the interrupt. The Continue/Busy bit is cleared by hardware prior to interrupt conditions 1 to 4. When the Data Register is read or written, firmware should configure the other control bits and set the Continue/Busy bit for subsequent transactions. Following an interrupt from master mode, firmware should perform only one write to the Status and Control Register that sets the Continue/Busy bit, without checking the value of the Continue/Busy bit. The Busy bit may otherwise be active and I2C register contents may be changed by the hardware during the transaction, until the I2C interrupt occurs. Document Number: 38-08024 Rev. *G Firmware is required to handle the following USB interface tasks: ■ Coordinate enumeration by responding to SETUP packets ■ Fill and empty the FIFOs ■ Suspend and Resume coordination ■ Verify and select DATA toggle values. USB Enumeration The internal hub and any compound device function are enumerated under firmware control. The hub is enumerated first, followed by any integrated compound function. After the hub is enumerated, the USB host reads hub connection status to determine which (if any) of the downstream ports need to be enumerated. The following is a brief summary of the typical enumeration process of the CY7C66x13C by the USB host. For a detailed description of the enumeration process, refer to the USB specification. In this description, “Firmware” refers to embedded firmware in the CY7C66x13C controller. 1. The host computer sends a SETUP packet followed by a DATA packet to USB address 0 requesting the Device descriptor. 2. Firmware decodes the request and retrieves its Device descriptor from the program memory tables. 3. The host computer performs a control read sequence and Firmware responds by sending the Device descriptor over the USB bus, via the on-chip FIFOs. 4. After receiving the descriptor, the host sends a SETUP packet followed by a DATA packet to address 0 assigning a new USB address to the device. Page 32 of 61 [+] Feedback CY7C66013C, CY7C66113C 5. Firmware stores the new address in its USB Device Address Register (for example, as Address B) after the no data control sequence completes. 6. The host sends a request for the Device descriptor using the new USB address. 7. Firmware decodes the request and retrieves the Device descriptor from program memory tables. 8. The host performs a control read sequence and Firmware responds by sending its Device descriptor over the USB bus. 9. The host generates control reads from the device to request the Configuration and Report descriptors. 10.When the device receives a Set Configuration request, its functions may now be used. 11.Following enumeration as a hub, Firmware optionally indicates to the host that a compound device exists (for example, the keyboard in a keyboard/hub device). 12.The host carries out the enumeration process with this additional function as though it were attached downstream from the hub. 13.When the host assigns an address to this device, it is stored as the other USB address (for example, Address A). USB Hub A USB hub is required to support: ■ Connectivity behavior: service connect and disconnect detection ■ Bus fault detection and recovery ■ Full and low speed device support. to a downstream port is through a differential signal pair (D+ and D–). Each downstream port provided by the hub requires external RUDN resistors from each signal line to ground, so that when a downstream port has no device connected, the hub reads a LOW (zero) on both D+ and D–. This condition is used to identify the “no connect” state. The hub must have a resistor RUUP connected between its upstream D+ line and VREG to indicate it is a full speed USB device. The hub generates an EOP at EOF1, in accordance with the USB 1.1 Specification, Section 11.2.2. Connecting and Disconnecting a USB Device A low speed (1.5 Mbps) USB device has a pull up resistor on the D– pin. At connect time, the bias resistors set the signal levels on the D+ and D– lines. When a low speed device is connected to a hub port, the hub sees a LOW on D+ and a HIGH on D–. This causes the hub repeater to set a connect bit in the Hub Ports Connect Status register for the downstream port. Then the hub repeater generates a Hub Interrupt to notify the microcontroller that there is a change in the Hub downstream status. A full speed (12 Mbps) USB device has a pull up resistor from the D+ pin, so the hub sees a HIGH on D+ and a LOW on D–. In this case, the hub repeater sets a connect bit in the Hub Ports Connect Status register, clears a bit in the Hub Ports Speed register (for full speed), and generates a Hub Interrupt to notify the microcontroller of the change in Hub status. The firmware sets the speed of this port in the Hub Ports Speed Register (see Table 35 on page 34). Connects are recorded by the time a non SE0 state lasts for more than 2.5 s on a downstream port. These features are mapped onto a hub repeater and a hub controller. The hub controller is supported by the processor integrated into the CY7C66013C and CY7C66113C microcontrollers. The hardware in the hub repeater detects whether a USB device is connected to a downstream port and the interface speed of the downstream device. The connection When a USB device is disconnected from the Hub, the downstream signal pair eventually floats to a single ended zero state. The hub repeater recognizes a disconnect when the SE0 state on a downstream port lasts from 2.0 to 2.5 s. On a disconnect, the corresponding bit in the Hub Ports Connect Status register is cleared, and the Hub Interrupt is generated. Table 34. Hub Ports Connect Status Hub Ports Connect Status Bit # 7 6 5 4 3 2 1 ADDRESS 0x48 0 Bit Name Reserved Reserved Reserved Reserved Port 4 Connect Status Port 3 Connect Status Port 2 Connect Status Port 1 Connect Status Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit [0..3]: Port x Connect Status (where x = 1..4) Bit [7..4]: Reserved. When set to 1, Port x is connected; When set to 0, Port x is disconnected. The Hub Ports Connect Status register is cleared to zero by reset or USB bus reset, then set to match the hardware configuration by the hub repeater hardware. The Reserved bits [7..4] should always read as ‘0’ to indicate no connection. Document Number: 38-08024 Rev. *G Page 33 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 35. Hub Ports Speed Hub Ports Speed Bit # 7 6 5 4 3 2 1 ADDRESS 0x4A 0 Bit Name Reserved Reserved Reserved Reserved Port 4 Speed Port 3 Speed Port 2 Speed Port 1 Speed Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit [0..3]: Port x Speed (where x = 1..4) Bit [7..4]: Reserved. Set to 1 if the device plugged in to Port x is Low speed; Set to 0 if the device plugged in to Port x is Full speed. The Hub Ports Speed register is cleared to zero by reset or bus reset. This must be set by the firmware on issuing a port reset. The Reserved bits [7..4] should always read as ‘0.’ Enabling and Disabling a USB Device After a USB device connection is detected, firmware must update status change bits in the hub status change data structure that is polled periodically by the USB host. The host responds by sending a packet that instructs the hub to reset and enable the downstream port. Firmware then sets the bit in the Hub Ports Enable register, Table 36, for the downstream port. The hub repeater hardware responds to an enable bit in the Hub Ports Enable register by enabling the downstream port, so that USB traffic flows to and from that port. If a port is marked enabled and is not suspended, it receives all USB traffic from the upstream port, and USB traffic from the downstream port is passed to the upstream port (unless babble is detected). Low speed ports do not receive full speed traffic from the upstream port. When firmware writes to the Hub Ports Enable register to enable a port, the port is not enabled until the end of any packet currently being transmitted. If there is no USB traffic, the port is enabled immediately. When a USB device disconnection is detected, firmware must update status bits in the hub change status data structure that is polled periodically by the USB host. In suspend, a connect or disconnect event generates an interrupt (if the hub interrupt is enabled) even if the port is disabled. Table 36. Hub Ports Enable Register Hub Ports Enable Register Bit # 7 6 5 4 3 2 1 ADDRESS 0x49 0 Bit Name Reserved Reserved Reserved Reserved Port 4 Enable Port 3 Enable Port 2 Enable Port 1 Enable Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit [0..3]: Port x Enable (where x = 1..4) Set to 1 if Port x is enabled; Set to 0 if Port x is disabled. cleared) if babble is detected on that downstream port. Babble is defined as: Bit [7..4]: Reserved. ■ The Hub Ports Enable register is cleared to zero by reset or bus reset to disable all downstream ports as the default condition. A port is also disabled by internal hub hardware (enable bit Any non idle downstream traffic on an enabled downstream port at EOF2 ■ Any downstream port with upstream connectivity established at EOF2 (that is, no EOP received by EOF2). Document Number: 38-08024 Rev. *G Page 34 of 61 [+] Feedback CY7C66013C, CY7C66113C Hub Downstream Ports Status and Control Data transfer on hub downstream ports is controlled according to the bit settings of the Hub Downstream Ports Control Register (Table 37). Each downstream port is controlled by two bits, as defined in Table 38. The Hub Downstream Ports Control Register is cleared upon reset or bus reset, and the reset state is the state for normal USB traffic. Any downstream port being forced must be marked as disabled (Table 36 on page 34) for proper operation of the hub repeater. Firmware uses this register for driving bus reset and resume signaling to downstream ports. Controlling the port pins through this register uses standard USB edge rate control according to the speed of the port, set in the Hub Port Speed Register. The downstream USB ports are designed for connection of USB devices, but also serves as output ports under firmware control. This allows unused USB ports to be used for functions such as driving LEDs or providing additional input signals. Pulling up these pins to voltages above VREF may cause current flow into the pin. This register is not reset by bus reset. These bits must be cleared before going into suspend. Table 37. Hub Downstream Ports Control Register Hub Downstream Ports Control Register ADDRESS 0x4B Bit # 7 6 5 4 3 2 1 0 Bit Name Port 4 Control Bit 1 Port 4 Control Bit 0 Port 3 Control Bit 1 Port 3 Control Bit 0 Port 2 Control Bit 1 Port 2 Control Bit 0 Port 1 Control Bit 1 Port 1 Control Bit 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Table 38. Control Bit Definition for Downstream Ports Control Bits Bit1 0 0 1 1 Control Action Bit 0 0 1 0 1 Not Forcing (Normal USB Function) Force Differential ‘1’ (D+ HIGH, D– LOW) Force Differential ‘0’ (D+ LOW, D– HIGH) Force SE0 state An alternate means of forcing the downstream ports is through the Hub Ports Force Low Register (Table 39). With these registers the pins of the downstream ports are individually forced LOW, or left unforced. Unlike the Hub Downstream Ports Control Register, above, the Force Low Register does not produce standard USB edge rate control on the forced pins. However, this register allows downstream port pins to be held LOW in suspend. This register is used to drive SE0 on all downstream ports when unconfigured, as required in the USB 1.1 specification. Table 39. Hub Ports Force Low Register Hub Ports Force Low Bit # 7 6 5 4 3 2 1 ADDRESS 0x51 0 Bit Name Force Low D+[4] Force Low D-[4] Force Low D+[3] Force Low D–[3] Force Low D+[2] Force Low D–[2] Force Low D+[1] Force Low D–[1] Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 The data state of downstream ports are read through the HUB Ports SE0 Status Register (Table 40 on page 36) and the Hub Ports Data Register (Table 41 on page 36). The data read from the Hub Ports Data Register is the differential data only and is independent of the settings of the Hub Ports Speed Register (Table 35 on page 34). When the SE0 condition is sensed on a downstream port, the corresponding bits of the Hub Ports Data Register hold the last differential data state before the SE0. Hub Ports SE0 Status Register and Hub Ports Data Register are cleared upon reset or bus reset. Document Number: 38-08024 Rev. *G Page 35 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 40. Hub Ports SE0 Status Register Hub Ports SE0 Status Bit # 7 6 5 4 3 2 1 ADDRESS 0x4F 0 Bit Name Reserved Reserved Reserved Reserved Port 4 SE0 Status Port 3 SE0 Status Port 2 SE0 Status Port 1 SE0 Status Read/Write - - - - R R R R Reset 0 0 0 0 0 0 0 0 Bit [0..3]: Port x SE0 Status (where x = 1..4) Bit [7..4]: Reserved. Set to 1 if a SE0 is output on the Port x bus; Set to 0 if a Non-SE0 is output on the Port x bus. Table 41. Hub Ports Data Register Hub Ports Data Bit # 7 6 5 4 3 2 1 ADDRESS 0x50 0 Bit Name Reserved Reserved Reserved Reserved Port 4 Diff. Data Port 3 Diff. Data Port 2 Diff. Data Port 1 Diff. Data Read/Write - - - - R R R R Reset 0 0 0 0 0 0 0 0 Bit [0..3]: Port x Diff Data (where x = 1..4) Bit [7..4]: Reserved. Set to 1 if D+ > D– (forced differential 1, if signal is differential, i.e. not a SE0 or SE1). Set to 0 if D– > D+ (forced differential 0, if signal is differential, i.e., not a SE0 or SE1); Downstream Port Suspend and Resume The Hub Ports Suspend Register (Table 42) and Hub Ports Resume Status Register (Table 49 on page 41) indicate the suspend and resume conditions on downstream ports. The suspend register must be set by firmware for any ports that are selectively suspended. Also, this register is only valid for ports that are selectively suspended. If a port is marked as selectively suspended, normal USB traffic is not sent to that port. Resume traffic is also prevented from going to that port, unless the Resume comes from the selectively suspended port. If a resume condition is detected on the port, hardware reflects a Resume back to the port, sets the Resume bit in the Hub Ports Resume Register, and generates a hub interrupt. If a disconnect occurs on a port marked as selectively suspended, the suspend bit is cleared. The Device Remote Wakeup bit (bit 7) of the Hub Ports Suspend Register controls whether or not the resume signal is propagated by the hub after a connect or a disconnect event. If the Device Remote Wakeup bit is set, the hub automatically propagates the resume signal after a connect or a disconnect event. If the Device Remote Wakeup bit is cleared, the hub does not propagate the resume signal. The setting of the Device Remote Wakeup flag has no impact on the propagation of the resume signal after a downstream remote wakeup event. The hub automatically propagates the resume signal after a remote wakeup event, regardless of the state of the Device Remote wakeup bit. The state of this bit has no impact on the generation of the hub interrupt. These registers are cleared on reset or USB bus reset. Table 42. Hub Ports Suspend Register Hub Ports Suspend Bit # 7 6 5 4 3 2 1 ADDRESS 0x4D 0 Bit Name Device Remote Wakeup Reserved Reserved Reserved Port 4 Selective Suspend Port 3 Selective Suspend Port 2 Selective Suspend Port 1 Selective Suspend Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bit [0..3]: Port x Selective Suspend (where x = 1..4) Bit 7: Device Remote Wakeup. Set to 1 if Port x is Selectively Suspended; Set to 0 if Port x Do not suspend. When set to 1, Enable hardware upstream resume signaling for connect and disconnect events during global resume. When set to 0, Disable hardware upstream resume signaling for connect and disconnect events during global resume. Document Number: 38-08024 Rev. *G Page 36 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 43. Hub Ports Resume Status Register Hub Ports Resume Bit # 7 6 5 4 3 2 1 ADDRESS 0x4E 0 Bit Name Reserved Reserved Reserved Reserved Resume 4 Resume 3 Resume 2 Resume 1 Read/Write - - - - R R R R Reset 0 0 0 0 0 0 0 0 Bit [0..3]: Resume x (where x = 1..4) When set to 1 Port x requesting to be resumed (set by hardware); default state is 0; Bit [7..4]: Reserved. The Reserved bits [7..4] should always read as ‘0’. Resume from a selectively suspended port, with the hub not in suspend, typically involves these actions: 1. Hardware detects the Resume, drives a K to the port, and generates the hub interrupt. The corresponding bit in the Resume Status Register (0x4E) reads ‘1’ in this case. 2. Firmware responds to hub interrupt, and reads register 0x4E to determine the source of the Resume. 3. Firmware begins driving K on the port for 10 ms or more through register 0x4B. 4. Firmware clears the Selective Suspend bit for the port (0x4D), which clears the Resume bit (0x4E). This ends the hardware driven Resume, but the firmware driven Resume continues. To prevent traffic being fed by the hub repeater to the port during or just after the Resume, firmware should disable this port. 5. Firmware drives a timed SE0 on the port for two low speed bit times as appropriate. Note Firmware must disable interrupts during this SE0 so the SE0 pulse is not inadvertently lengthened and appears as a bus reset to the downstream device. Document Number: 38-08024 Rev. *G 6. Firmware drives a J on the port for one low speed bit time, then it idles the port. 7. Firmware re-enables the port. Resume when the hub is suspended typically involves these actions: 1. Hardware detects the Resume, drives a K on the upstream (which is then reflected to all downstream enabled ports), and generates the hub interrupt. 2. The part comes out of suspend and the clocks start. 3. When the clocks are stable, firmware execution resumes. An internal counter ensures that this takes at least 1 ms. Firmware should check for Resume from any selectively suspended ports. If found, the Selective Suspend bit for the port should be cleared; no other action is necessary. 4. The Resume ends when the host stops sending K from upstream. Firmware should check for changes to the Enable and Connect Registers. If a port has become disabled but is still connected, an SE0 is detected on the port. The port is treated as being reset, and is reported to the host as newly connected. Firmware chooses to clear the Device Remote Wakeup bit (if set) to implement firmware timed states for port changes. All allowed port changes wake the part. Then, the part uses internal timing to determine whether to take action or return to suspend. If Device Remote Wakeup is set, automatic hardware assertions take place on Resume events. Page 37 of 61 [+] Feedback CY7C66013C, CY7C66113C USB Upstream Port Status and Control USB status and control is regulated by the USB Status and Control Register, as shown in Table 44. All bits in the register are cleared during reset. Table 44. USB Status and Control Register USB Status and Control Bit # 7 6 5 4 3 2 1 ADDRESS 0 Bit Name Endpoint Size Endpoint Mode D+ Upstream D– Upstream Bus Activity Control Action Bit 2 Control Action Bit 1 Control Action Bit 0 Read/Write R/W R/W R R R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 0x1F Bits[2..0]: Control Action Set to control action as per Table 45.The three control bits allow the upstream port to be driven manually by firmware. For normal USB operation, all of these bits must be cleared. Table 45 shows how the control bits affect the upstream port. Table 45. Control Bit Definition for Upstream Port Control Bits Control Action 000 Not Forcing (SIE Controls Driver) 001 Force D+[0] HIGH, D–[0] LOW 010 Force D+[0] LOW, D–[0] HIGH 011 Force SE0; D+[0] LOW, D–[0] LOW 100 Force D+[0] LOW, D–[0] LOW 101 Force D+[0] HiZ, D–[0] LOW 110 Force D+[0] LOW, D–[0] HiZ 111 Force D+[0] HiZ, D–[0] HiZ Bit 3: Bus Activity Bit 6: Endpoint Mode This is a “sticky” bit that indicates if any non idle USB event has occurred on the upstream USB port. Firmware should check and clear this bit periodically to detect any loss of bus activity. Writing a ‘0’ to the Bus Activity bit clears it, while writing a ‘1’ preserves the current value. In other words, the firmware clears the Bus Activity bit, but only the SIE can set it. This bit used to configure the number of USB endpoints. See USB Device Endpoints on page 39 for a detailed description. Bit 7: Endpoint Size Bits 4 and 5: D– Upstream and D+ Upstream The hub generates an EOP at EOF1 in accordance with the USB 1.1 Specification. These bits give the state of each upstream port pin individually: 1 = HIGH, 0 = LOW. Document Number: 38-08024 Rev. *G This bit used to configure the number of USB endpoints. See USB Device Endpoints on page 39 for a detailed description. Page 38 of 61 [+] Feedback CY7C66013C, CY7C66113C USB SIE Operation USB Device Addresses The CY7C66x13C SIE supports operation as a single device or a compound device. This section describes the two device addresses, the configurable endpoints, and the endpoint function. The USB Controller provides two USB Device Address Registers: A (addressed at 0x10)and B (addressed at 0x40). Upon reset and under default conditions, Device A has three endpoints and Device B has two endpoints. The USB Device Address Register contents are cleared during a reset, setting the USB device addresses to zero and disabling these addresses. Table 46 shows the format of the USB Address Registers. Table 46. USB Device Address Registers USB Device Address (Device A, B) Bit # 7 6 Bit Name Device Address Enable Device Address Bit 6 ADDRESSES 1 5 4 3 2 Device Address Bit 5 Device Address Bit 4 Device Address Bit 3 Device Address Bit 2 0x10(A) and 0x40(B) 0 Device Address Bit 1 Device Address Bit 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bits[6..0]: Device Address Bit 7: Device Address Enable Firmware writes this bits during the USB enumeration process to the non zero address assigned by the USB host. Must be set by firmware before the SIE responds to USB traffic to the Device Address. USB Device Endpoints The CY7C66x13C controller supports up to two addresses and five endpoints for communication with the host. The configuration of these endpoints, and associated FIFOs, is controlled by bits [7,6] of the USB Status and Control Register (see Table 44 on page 38). Bit 7 controls the size of the endpoints and bit 6 controls the number of addresses. These configuration options are detailed in Table 47. Endpoint FIFOs are part of user RAM (as shown in Data Memory Organization on page 13). Table 47. Memory Allocation for Endpoints USB Status And Control Register (0x1F) Bits [7, 6] [0,0] [1,0] Two USB Addresses: A (3 End- Two USB Addresses: A (3 Endpoints) & B (2 Endpoints) points) &B (2 Endpoints) [0,1] [1,1] One USB Address: A (5 Endpoints) One USB Address: A (5 Endpoints) Label Start Address Size Label Start Address Size Label Start Address Size Label Start Address Size EPB1 0xD8 8 EPB0 0xA8 8 EPA4 0xD8 8 EPA3 0xA8 8 EPB0 0xE0 8 EPB1 0xB0 8 EPA3 0xE0 8 EPA4 0xB0 8 EPA2 0xE8 8 EPA0 0xB8 8 EPA2 0xE8 8 EPA0 0xB8 8 EPA1 0xF0 8 EPA1 0xC0 32 EPA1 0xF0 8 EPA1 0xC0 32 EPA0 0xF8 8 EPA2 0xE0 32 EPA0 0xF8 8 EPA2 0xE0 32 When the SIE writes data to a FIFO, the internal data bus is driven by the SIE; not the CPU. This causes a short delay in the CPU operation. The delay is three clock cycles per byte. For example, an 8-byte data write by the SIE to the FIFO generates a delay of 2 s (3 cycles/byte * 83.33 ns/cycle * 8 bytes). USB Control Endpoint Mode Registers other endpoints are unidirectional, but selectable by the user as IN or OUT endpoints. The endpoint mode registers are cleared during reset. When USB Status And Control Register Bits [6,7] are set to [0,0] or [1,0], the endpoint 0 EPA0 and EPB0 mode registers use the format shown in Table 48 on page 40. All USB devices are required to have a control endpoint 0 (EPA0 and EPB0) that is used to initialize and control each USB address. Endpoint 0 provides access to the device configuration information and allows generic USB status and control accesses. Endpoint 0 is bidirectional to both receive and transmit data. The Document Number: 38-08024 Rev. *G Page 39 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 48. USB Endpoint 0 Mode Registers USB Device Endpoint Zero Mode (A0, B0) Bit # 7 6 5 4 3 2 ADDRESSES 1 0x12(A0) and 0x42(B0) 0 Bit Name Endpoint 0 SETUP Received Endpoint 0 IN Endpoint 0 Received OUT Received ACK Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bits[3..0]: Mode These sets the mode which control how the control endpoint responds to traffic. Bit 4: ACK This bit is set whenever the SIE engages in a transaction to the register’s endpoint that completes with an ACK packet. Bit 5: Endpoint 0 OUT Received 1 = Token received is an OUT token. 0 = Token received is not an OUT token. This bit is set by the SIE to report the type of token received by the corresponding device address is an OUT token. The bit must be cleared by firmware as part of the USB processing. Bit 6: Endpoint 0 IN Received 1 = Token received is an IN token. 0 = Token received is not an IN token. This bit is set by the SIE to report the type of token received by the corresponding device address is an IN token. The bit must be cleared by firmware as part of the USB processing. Bit 7: Endpoint 0 SETUP Received 1 = Token received is a SETUP token. 0 = Token received is not a SETUP token. This bit is set ONLY by the SIE to report the type of token received by the corresponding device address is a SETUP token. Any write to this bit by the CPU clears it (set it to 0). The bit is forced HIGH from the start of the data packet phase of the SETUP transaction until the start of the ACK packet returned by the SIE. The CPU should not clear this bit during this interval, and subsequently, until the CPU first does an IORD to this endpoint 0 mode register. The bit must be cleared by firmware as part of the USB processing. Document Number: 38-08024 Rev. *G Note In 5-endpoint mode (USB Status And Control Register Bits [7,6] are set to [0,1] or [1,1]), Register 0x42 serves as non control endpoint 3, and has the format for non control endpoints shown in Table 49 on page 41. Bits[6:0] of the endpoint 0 mode register are locked from CPU write operations whenever the SIE has updated one of these bits, which the SIE does only at the end of the token phase of a transaction (SETUP... Data... ACK, OUT... Data... ACK, or IN... Data... ACK). The CPU unlocks these bits by doing a subsequent read of this register. Only endpoint 0 mode registers are locked when updated. The locking mechanism does not apply to the mode registers of other endpoints. Because of these hardware locking features, firmware must perform an IORD after an IOWR to an endpoint 0 register. This verifies that the contents have changed as desired, and that the SIE has not updated these values. While the SETUP bit is set, the CPU cannot write to the endpoint zero FIFOs. This prevents firmware from overwriting an incoming SETUP transaction before firmware has a chance to read the SETUP data. Refer to Table 47 on page 39 for the appropriate endpoint zero memory locations. The Mode bits (bits [3:0]) control how the endpoint responds to USB bus traffic. The mode bit encoding is shown in Table 38 on page 35. Additional information on the mode bits are found in Table 52 on page 45 and Table 51 on page 44. Note The SIE offers an “Ack out - Status in” mode and not an “Ack out - Nak in” mode. Therefore, if following the status stage of a Control Write transfer a USB host were to immediately start the next transfer, the new Setup packet could override the data payload of the data stage of the previous Control Write. Page 40 of 61 [+] Feedback CY7C66013C, CY7C66113C USB Non Control Endpoint Mode Registers The format of the non control endpoint mode registers is shown in Table 49. Table 49. USB Non Control Endpoint Mode Registers USB Non Control Device Endpoint Mode Bit # 7 6 5 Bit Name STALL Reserved Reserved ADDRESSES 0x14, 0x16, 0x44 1 0 4 3 2 ACK Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bits[3..0]: Mode Bits[6..5]: Reserved These sets the mode which control how the control endpoint responds to traffic. The mode bit encoding is shown in Table 38 on page 35. Must be written zero during register writes. Bit 4: ACK This bit is set whenever the SIE engages in a transaction to the register’s endpoint that completes with an ACK packet. Bit 7: STALL If this STALL is set, the SIE stalls an OUT packet if the mode bits are set to ACK-IN, and the SIE stalls an IN packet if the mode bits are set to ACK-OUT. For all other modes, the STALL bit must be a LOW. USB Endpoint Counter Registers There are five Endpoint Counter registers, with identical formats for both control and non control endpoints. These registers contain byte count information for USB transactions, and bits for data packet status. The format of these registers is shown in Table 50. Table 50. USB Endpoint Counter Registers USB Endpoint Counter Bit # 7 6 5 4 3 ADDRESSES 2 0x11, 0x13, 0x15, 0x41, 0x43 1 0 Bit Name Data 0/1 Toggle Data Valid Byte Count Bit 5 Byte Count Bit 4 Byte Count Bit 3 Byte Count Bit 2 Byte Count Bit 1 Byte Count Bit 0 Read/Write R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 Bits[5..0]: Byte Count Bit 7: Data 0/1 Toggle These counter bits indicate the number of data bytes in a transaction. For IN transactions, firmware loads the count with the number of bytes to be transmitted to the host from the endpoint FIFO. Valid values are 0 to 32, inclusive. For OUT or SETUP transactions, the count is updated by hardware to the number of data bytes received, plus two for the CRC bytes. Valid values are 2 to 34, inclusive. This bit selects the DATA packet’s toggle state: 0 for DATA0, 1 for DATA1. For IN transactions, firmware must set this bit to the desired state. For OUT or SETUP transactions, the hardware sets this bit to the state of the received Data Toggle bit. Bit 6: Data Valid This bit is set on receiving a proper CRC when the endpoint FIFO buffer is loaded with data during transactions. This bit is used OUT and SETUP tokens only. If the CRC is not correct, the endpoint interrupt occurs, but Data Valid is cleared to a zero. Document Number: 38-08024 Rev. *G Whenever the count updates from a SETUP or OUT transaction on endpoint 0, the counter register locks and cannot be written by the CPU. Reading the register unlocks it. This prevents firmware from overwriting a status update on incoming SETUP or OUT transactions before firmware has a chance to read the data. Only endpoint 0 counter register is locked when updated. The locking mechanism does not apply to the count registers of other endpoints. Page 41 of 61 [+] Feedback CY7C66013C, CY7C66113C Endpoint Mode and Count Registers Update and Locking Mechanism The contents of the endpoint mode and counter registers are updated, based on the packet flow diagram in Figure 11 on page 43. Two time points, UPDATE and SETUP, are shown in the same figure. The following activities occur at each time point: SETUP: The SETUP bit of the endpoint 0 mode register is forced HIGH at this time. This bit is forced HIGH by the SIE until the end of the data phase of a control write transfer. The SETUP bit can not be cleared by firmware during this time. The affected mode and counter registers of endpoint 0 are locked from any CPU writes when they are updated. These registers are unlocked by a CPU read, only if the read operation occurs after the UPDATE. The firmware needs to perform a register read as a part of the endpoint ISR processing to unlock Document Number: 38-08024 Rev. *G the effected registers. The locking mechanism on mode and counter registers ensures that the firmware recognizes the changes that the SIE might have made since the previous I/O read of that register. UPDATE: 1. Endpoint Mode Register – All the bits are updated (except the SETUP bit of the endpoint 0 mode register). 2. Counter Registers – All bits are updated. 3. Interrupt – If an interrupt is to be generated as a result of the transaction, the interrupt flag for the corresponding endpoint is set at this time. For details on what conditions are required to generate an endpoint interrupt, refer to Table 52 on page 45. 4. The contents of the updated endpoint 0 mode and counter registers are locked, except the SETUP bit of the endpoint 0 mode register which was locked earlier. Page 42 of 61 [+] Feedback CY7C66013C, CY7C66113C Figure 11. Token and Data Packet Flow Diagram 1. IN Token Host To Device S Y N C IN A D D R E N D P Device To Host C R C 5 D A T A 1/0 S Y N C Token Packet H O S T IN A D D R E N D P C R C 16 S Y N C A C K Hand Shake Packet Data Packet Host To Device S Y N C Data Host To Device UPDATE Device To Host C R C 5 S Y N C Token Packet NAK/STALL Data Packet UPDATE 2. OUT or SETUP Token without CRC error S Y N C O U T / Set up A D D R E N D P Device To Host Host To Device Host To Device C R C 5 S Y N C Token Packet D A T A 1/0 Data C R C 16 Data Packet UPDATE SETUP S Y N C D E V I C E ACK, NAK, STAL Hand Shake Packet 3. OUT or SETUP Token with CRC error Host To Device S Y N C O U T / Set up A D D R E N D P Token Packet Host To Device C R C 5 S Y N C D A T A 1/0 Data C R C 16 Data Packet UPDATE only if FIFO is written Document Number: 38-08024 Rev. *G Page 43 of 61 [+] Feedback CY7C66013C, CY7C66113C USB Mode Tables Table 51. USB Register Mode Encoding Mode Disable Mode SETUP Bits 0000 ignore IN ignore OUT Comments ignore Ignore all USB traffic to this endpoint Nak In/Out 0001 accept NAK NAK Forced from Setup on Control endpoint, from modes other than 0000 Status Out Only 0010 accept stall check For Control endpoints For Control endpoints Stall In/Out 0011 accept stall stall Ignore In/Out 0100 accept ignore ignore For Control endpoints Isochronous Out 0101 ignore always For Isochronous endpoints Status In Only 0110 accept TX 0 Byte stall Isochronous In 0111 ignore TX count ignore For Isochronous endpoints Nak Out 1000 ignore ignore NAK Is set by SIE on an ACK from mode 1001 (Ack Out) 1001 1001 ignore ignore ignore ignore ACK stall On issuance of an ACK this mode is changed by SIE to 1000 (NAK Out) Nak Out-Status In 1010 accept TX 0 Byte NAK Is set by SIE on an ACK from mode 1011 (Ack Out-Status In) Ack Out-Status In 1011 accept TX 0 Byte ACK On issuance of an ACK this mode is changed by SIE to 1010 (NAK Out – Status In) Nak In Ack Ack Out(STALL[4]=0) Out(STALL[4]=1) ignore For Control Endpoints 1100 ignore NAK IN(STALL[4]=0) [4]=1) ignore Is set by SIE on an ACK from mode 1101 (Ack In) Ack Ack IN(STALL 1101 1101 ignore ignore TX count ignore On issuance of an ACK this mode is changed by SIE to 1100 (NAK In) stall ignore Nak In – Status Out 1110 accept NAK Ack In – Status Out 1111 accept TX Count check check Is set by SIE on an ACK from mode 1111 (Ack In – Status Out) On issuance of an ACK this mode is changed by SIE to 1110 (NAK In – Status Out) Mode This lists the mnemonic given to the different modes that are set in the Endpoint Mode Register by writing to the lower nibble (bits 0..3). The bit settings for different modes are covered in the column marked “Mode Bits.” The Status IN and Status OUT represent the Status stage in the IN or OUT transfer involving the control endpoint. Mode Bits These column lists the encoding for different modes by setting Bits[3..0] of the Endpoint Mode register. This modes represents how the SIE responds to different tokens sent by the host to an endpoint. For instance, if the mode bits are set to “0001” (NAK IN/OUT), the SIE responds with an ■ ACK on receiving a SETUP token from the host ■ NAK on receiving an OUT token from the host ■ NAK on receiving an IN token from the host I2C Refer to Compatible Controller on page 23 for more information on SIE functioning. SETUP, IN, and OUT These columns shows the SIE’s response to the host on receiving a SETUP, IN, and OUT token depending on the mode set in the Endpoint Mode Register. A “Check” on the OUT token column, implies that on receiving an OUT token the SIE checks to see whether the OUT packet is of zero length and has a Data Toggle (DTOG) set to ‘1.’ If the DTOG bit is set and the received OUT Packet has zero length, the OUT is ACKed to complete the transaction. If either of this condition is not met the SIE responds with a STALLL or just ignore the transaction. A “TX Count” entry in the IN column implies that the SIE transmit the number of bytes specified in the Byte Count (bits 3..0 of the Endpoint Count Register) to the host in response to the IN token received. A “TX0 Byte” entry in the IN column implies that the SIE transmit a zero length byte packet in response to the IN token received from the host. An “Ignore” in any of the columns means that the device does not send any handshake tokens (no ACK) to the host. An “Accept” in any of the columns means that the device responds with an ACK to a valid SETUP transaction to the host. Comments Some Mode Bits are automatically changed by the SIE in response to certain USB transactions. For example, if the Mode Bits [3:0] are set to '1111' which is ACK IN-Status OUT mode as shown in Table 47 on page 39, the SIE changes the endpoint Mode Bits [3:0] to NAK IN-Status OUT mode (1110) after ACK’ing Note 4. STALL bit is bit 7 of the USB Non Control Device Endpoint Mode registers. For more information, refer to USB Non Control Endpoint Mode Registers on page 41. Document Number: 38-08024 Rev. *G Page 44 of 61 [+] Feedback CY7C66013C, CY7C66113C and OUTs). Any mode set to accept a SETUP sends an ACK handshake to a valid SETUP token. a valid status stage OUT token. The firmware needs to update the mode for the SIE to respond appropriately. See Table 38 on page 35 for more details on what modes are changed by the SIE. A disabled endpoint remains disabled until changed by firmware, and all endpoints reset to the disabled mode (0000). Firmware normally enables the endpoint mode after a SetConfiguration request. The control endpoint has three status bits for identifying the token type received (SETUP, IN, or OUT), but the endpoint must be placed in the correct mode to function as such. Non control endpoints should not be placed into modes that accept SETUPs. Note that most modes that control transactions involving an ending ACK, are changed by the SIE to a corresponding mode which NAKs subsequent packets following the ACK. Exceptions are modes 1010 and 1110. Any SETUP packet to an enabled endpoint with mode set to accept SETUPs are changed by the SIE to 0001 (NAKing INs Table 52. Decode Table for Table 53 Properties of Incoming Packets 3 2 1 0 Token count buffer Changes to the Internal Register made by the SIE on receiving an incoming packet from the host dval DTOG DVAL COUNT Setup In Out ACK 3 2 1 Interrupt 0 Response Int Byte Count (bits 0..5, Figure 17-4) Endpoint Mode encoding Data Valid (bit 6, Figure 17-4) Received Token (SETUP/IN/OUT) SIE’s Response to the Host Data0/1 (bit7 Figure 17-4) PID Status Bits (Bit[7..5], Figure 17-2) The validity of the received data Endpoint Mode bits Changed by the SIE The quality status of the DMA buffer The number of received bytes Legend: TX: transmit UC : unchanged RX: receive TX0:Transmit 0 length packet Acknowledge phase completed available for Control endpoint only x: don’t care The response of the SIE are summarized as follows: ■ The SIE only responds to valid transactions, and ignores invalid ones. ■ The SIE generates an interrupt when a valid transaction is completed or when the FIFO is corrupted. FIFO corruption occurs during an OUT or SETUP transaction to a valid internal address, that ends with a invalid CRC. ■ An incoming Data packet is valid if the count is < Endpoint Size + 2 (includes CRC) and passes all error checking. ■ An IN is ignored by an OUT configured endpoint and visa versa. ■ The IN and OUT PID status is updated at the end of a transaction. ■ The SETUP PID status is updated at the beginning of the Data packet phase. Document Number: 38-08024 Rev. *G ■ The entire Endpoint 0 mode register and the Count register are locked to CPU writes at the end of any transaction to that endpoint in which an ACK is transferred. These registers are only unlocked by a CPU read of the register, which should be done by the firmware only after the transaction is complete. This represents about a 1 s window in which the CPU is locked from register writes to these USB registers. Normally the firmware should perform a register read at the beginning of the Endpoint ISRs to unlock and get the mode register information. The interlock on the Mode and Count registers ensures that the firmware recognizes the changes that the SIE might have made during the previous transaction. Note that the setup bit of the mode register is NOT locked. This means that before writing to the mode register, firmware must first read the register to make sure that the setup bit is not set (which indicates a setup was received, while processing the current USB request). This read unlocks the register. So care must be taken not to overwrite the register elsewhere. Page 45 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 53. Details of Modes for Differing Traffic Conditions (see Table 52 on page 45 for the decode legend) Properties of Incoming Packet Mode Bits token count buffer dval See Table 33 Setup <= 10 data valid See Table 33 Setup > 10 junk x See Table 33 Setup x junk invalid Properties of Incoming Packet Mode Bits token count buffer dval DISABLED 0 0 0 0 x x UC x Nak In/Out 0 0 0 1 Out x UC x 0 0 0 1 In x UC x Ignore In/Out 0 1 0 0 Out x UC x 0 1 0 0 In x UC x Stall In/Out 0 0 1 1 Out x UC x 0 0 1 1 In x UC x Properties of Incoming Packet Mode Bits token count buffer dval Normal Out/premature status In 1 0 1 1 Out <= 10 data valid 1 0 1 1 Out > 10 junk x 1 0 1 1 Out x junk invalid 1 0 1 1 In x UC x NAK Out/premature status In 1 0 1 0 Out <= 10 UC valid 1 0 1 0 Out > 10 UC x 1 0 1 0 Out x UC invalid 1 0 1 0 In x UC x Status In/extra Out 0 1 1 0 Out <= 10 UC valid 0 1 1 0 Out > 10 UC x 0 1 1 0 Out x UC invalid 0 1 1 0 In x UC x Properties of Incoming Packet Mode Bits token count buffer dval Normal In/premature status Out 1 1 1 1 Out 2 UC valid 1 1 1 1 Out 2 UC valid 1 1 1 1 Out !=2 UC valid 1 1 1 1 Out > 10 UC x 1 1 1 1 Out x UC invalid 1 1 1 1 In x UC x Document Number: 38-08024 Rev. *G SETUP (if accepting SETUPs) Changes made by SIE to Internal Registers and Mode Bits DTOG DVAL COUNT Setup In Out ACK Mode Bits Response Intr updates 1 updates 1 UC UC 1 0 0 0 1 ACK yes updates updates updates 1 UC UC UC No Change ignore yes updates 0 updates 1 UC UC UC No Change ignore yes Changes made by SIE to Internal Registers and Mode Bits DTOG DVAL COUNT Setup In Out ACK Mode Bits Response Intr UC UC UC UC UC UC UC No Change ignore no UC UC UC UC UC UC UC UC UC 1 1 UC UC UC No Change NAK No Change NAK yes yes UC UC UC UC UC UC UC UC UC UC UC UC UC UC No Change ignore No Change ignore no no UC UC UC UC UC UC 1 UC No Change Stall yes UC UC UC 1 UC UC No Change Stall yes CONTROL WRITE Changes made by SIE to Internal Registers and Mode Bits DTOG DVAL COUNT Setup In Out ACK Mode Bits Response Intr updates updates updates UC 1 updates 0 UC updates updates updates UC UC UC UC UC UC UC UC 1 1 1 1 UC 1 UC UC 1 1 0 1 0 ACK No Change ignore No Change ignore No Change TX 0 yes yes yes yes UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC 1 1 UC UC UC UC UC UC 1 No Change NAK No Change ignore No Change ignore No Change TX 0 yes no no yes UC UC UC UC UC UC UC UC 1 UC 0 0 1 1 Stall UC UC UC UC UC UC No Change ignore UC UC UC UC UC UC No Change ignore UC UC UC 1 UC 1 No Change TX 0 CONTROL READ Changes made by SIE to Internal Registers and Mode Bits DTOG DVAL COUNT Setup In Out ACK Mode Bits Response 1 0 updates UC UC UC 1 1 1 UC UC UC updates updates updates UC UC UC UC UC UC UC UC UC UC UC UC UC UC 1 1 1 1 UC UC UC 1 UC UC UC UC 1 No Change ACK 0 0 1 1 Stall 0 0 1 1 Stall No Change ignore No Change ignore 1 1 1 0 ACK (back) yes no no yes Intr yes yes yes no no yes Page 46 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 53. Details of Modes for Differing Traffic Conditions (see Table 52 on page 45 for the decode legend) (continued) Nak In/premature status Out 1 1 1 0 Out 2 1 1 1 0 Out 2 1 1 1 0 Out !=2 1 1 1 0 Out > 10 1 1 1 0 Out x 1 1 1 0 In x Status Out/extra In 0 0 1 0 Out 2 0 0 1 0 Out 2 0 0 1 0 Out !=2 0 0 1 0 Out > 10 0 0 1 0 Out x 0 0 1 0 In x UC UC UC UC UC UC valid valid valid x invalid x 1 0 updates UC UC UC UC UC UC UC UC UC valid valid valid x invalid x 1 0 updates UC UC UC 1 1 1 UC UC UC updates updates updates UC UC UC UC UC UC UC UC UC UC UC UC UC UC 1 1 1 1 UC UC UC 1 UC UC UC UC UC 1 updates UC UC 1 1 No Change ACK 1 updates UC UC 1 UC 0 0 1 1 Stall 1 updates UC UC 1 UC 0 0 1 1 Stall UC UC UC UC UC UC No Change ignore UC UC UC 1 UC UC No Change ignore UC UC UC 1 UC UC 0 0 1 1 Stall OUT ENDPOINT Changes made by SIE to Internal Registers and Mode Bits DTOG DVAL COUNT Setup In Out ACK Mode Bits Response Properties of Incoming Packet Mode Bits token count buffer dval Normal Out/erroneous In 1 0 0 1 Out <= 10 data valid 1 0 0 1 Out > 10 junk x 1 0 0 1 Out x junk invalid 1 0 0 1 In x UC x updates updates updates UC 1 updates 0 UC updates updates updates UC UC UC UC UC UC UC UC UC 1 1 1 UC 1 UC UC UC 1 0 0 1 In x NAK Out/erroneous In 1 0 0 0 Out <= 10 1 0 0 0 Out > 10 1 0 0 0 Out x 1 0 0 0 In x Isochronous endpoint (Out) 0 1 0 1 Out x 0 1 0 1 In x No Change ACK 0 0 1 1 Stall 0 0 1 1 Stall No Change ignore No Change ignore No Change NAK UC x UC UC UC UC UC UC UC UC UC UC UC valid x invalid x UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC UC 1 UC UC UC yes yes yes no no yes Intr 1 0 0 0 ACK No Change ignore No Change ignore No Change ignore (STALL[4] = 0) No Change Stall (STALL[4] = 1) yes yes yes no No Change NAK No Change ignore No Change ignore No Change ignore yes no no no updates updates updates updates updates UC UC 1 1 No Change RX UC x UC UC UC UC UC UC UC No Change ignore IN ENDPOINT Properties of Incoming Packet Changes made by SIE to Internal Registers and Mode Bits Mode Bits token count buffer dval DTOG DVAL COUNT Setup In Out ACK Mode Bits Response Normal In/erroneous Out 1 1 0 1 Out x UC x UC UC UC UC UC UC UC No Change ignore (STALL[4] = 0) 1 1 0 1 Out x UC x UC UC UC UC UC UC UC No Change stall (STALL[4] = 1) 1 1 0 1 In x UC x UC UC UC UC 1 UC 1 1 1 0 0 ACK (back) NAK In/erroneous Out 1 1 0 0 Out x UC x UC UC UC UC UC UC UC No Change ignore Document Number: 38-08024 Rev. *G yes yes yes no no yes no yes no Intr no no yes no Page 47 of 61 [+] Feedback CY7C66013C, CY7C66113C Table 53. Details of Modes for Differing Traffic Conditions (see Table 52 on page 45 for the decode legend) (continued) 1 1 0 0 In x Isochronous endpoint (In) 0 1 1 1 Out x 0 1 1 1 In x UC x UC UC UC UC 1 UC UC No Change NAK yes UC UC x x UC UC UC UC UC UC UC UC UC UC 1 UC UC UC No Change ignore No Change TX no yes Register Summary USB- Endpoint A0, AI AND A2 Configuration Endpoint A0, AI HAPI GPIO CONFIGURATION PORTS 0, 1, 2 AND 3 CS and A2 Configuration I2C Addr Register Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Read/Write/ Default/ Both[5, 6, 7] Reset [8] 0x00 Port 0 Data P0.7 P0.6 P0.5 P0.4 P0.3 P0.2 P0.1 P0.0 bbbbbbbb 11111111 0x01 Port 1 Data P1.7 P1.6 P1.5 P1.4 P1.3 P1.2 P1.1 P1.0 bbbbbbbb 11111111 0x02 Port 2 Data P2.7 P2.6 P2.5 P2.4 P2.3 P2.2 P2.1 P2.0 bbbbbbbb 11111111 0x03 Port 3 Data Reserved P3.6 P3.5 P3.4 P3.3 P3.2 P3.1 P3.0 bbbbbbbb -1111111 0x04 Port 0 Interrupt Enable P0.7 Intr Enable P0.6 Intr Enable P0.5 Intr Enable P0.4 Intr Enable P0.3 Intr Enable P0.2 Intr Enable P0.1 Intr Enable P0.0 Intr Enable wwwwwwww 00000000 0x05 Port 1 Interrupt Enable P1.7 Intr Enable P1.6 Intr Enable P1.5 Intr Enable P1.4 Intr Enable P1.3 Intr Enable P1.2 Intr Enable P1.1 Intr Enable P1.0 Intr Enable wwwwwwww 00000000 0x06 Port 2 Interrupt Enable P2.7 Intr Enable P2.3 Intr Enable P2.2 Intr Enable P2.1 Intr Enable P2.0 Intr Enable wwwwwwww 00000000 Port 3 Interrupt Enable P2.5 Intr Enable P3.5 Intr Enable P2.4 Intr Enable 0x07 P2.6 Intr Enable Reserved P3.6 Intr Enable P3.4 Intr Enable P3.3 Intr Enable P3.2 Intr Enable P3.1 Intr Enable P3.0 Intr Enable wwwwwwww 00000000 CY7C66113C CY7C66113C only only CY7C66113C CY7C66113C only only 0x08 GPIO Configuration Port 3 Port 3 Port 2 Port 2 Port 1 Port 1 Port 0 Port 0 bbbbbbbb Config Bit Config Bit Config Bit Config Bit Config Bit Config Bit Config Bit Config Bit 1 0 1 0 1 0 1 0 00000000 0x09 HAPI/I2C Configuration I2 C Position 0x10 USB Device Address A Device Device Address A Address Enable A Bit 6 Device Address A Bit 5 0x11 EP A0 Counter Register Data 0/1 Toggle Byte Count Bit 5 0x12 EP A0 Mode Register 0x13 Reserved LEMPTY DRDY Polarity Polarity Latch Empty Data Ready Port Width Port Width b-bbrrbb bit 1 bit 0 00000000 Device Address A Bit 4 Device Address A Bit 3 Device Address A Bit 2 Device Ad- Device dress Address A Bit 1 A Bit 0 bbbbbbbb 00000000 Byte Count Bit 4 Byte Count Bit 3 Byte Count Bit 2 Byte Count Byte Bit 1 Count Bit 0 bbbbbbbb 00000000 Endpoint0 Endpoint0 Endpoint0 ACK SETUP IN OUT Received Received Received Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0 bbbbbbbb 00000000 EP A1 Counter Register Data 0/1 Toggle Data Valid Byte Count Bit 5 Byte Count Bit 4 Byte Count Bit 3 bbbbbbbb 00000000 0x14 EP A1 Mode Register STALL - ACK Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0 bbbbbbbb 00000000 0x15 EP A2 Counter Register Data 0/1 Toggle Data Valid Byte Count Bit 5 Byte Count Bit 4 Byte Count Bit 3 bbbbbbbb 00000000 0x16 EP A2 Mode Register STALL - ACK Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0 bbbbbbbb 00000000 0x1F USB Status and Control Endpoint Endpoint D+ D– Bus Size Mode Upstream Upstream Activity Data Valid - - Byte Count Bit 2 Byte Count Bit 2 Control Bit 2 Byte Count Byte Bit 1 Count Bit 0 Byte Count Byte Bit 1 Count Bit 0 Control Bit 1 Control Bit 0 bbrrbbbb -0xx0000 Notes 5. B: Read and Write. 6. W: Write. 7. R: Read. 8. X: Unknown Document Number: 38-08024 Rev. *G Page 48 of 61 [+] Feedback CY7C66013C, CY7C66113C Register Summary HUB PORT CONTROL, STATUS, SUSPEND RESUME, SE0, FORCE LOW ENDPOINT B0, B1 CONFIGURATION I2C TIMER INTERRUPT Addr Register Name (continued) Bit 7 Bit 6 Bit 5 Bit 4 GPIO Interrupt Enable DAC Interrupt Enable Bit 3 Bit 2 Bit 1 Bit 0 Read/Write/ Default/ Both[5, 6, 7] Reset [8] 0x20 Global Interrupt Enable Reserved I2C Interrupt Enable 0x21 Endpoint Interrupt Enable Reserved Reserved Reserved EPB1 Interrupt Enable 0x24 Timer (LSB) Timer Bit 7 Timer Bit 6 Timer Bit 5 Timer Bit 4 Timer Bit 3 Timer Bit 2 Timer Bit 1 Timer Bit 0 rrrrrrrr 00000000 0x25 Timer (MSB) Reserved Reserved Reserved Reserved Timer Bit Timer Bit Time Bit 9 Timer Bit 8 ----rrrr 11 10 ----0000 0x28 I2C Control and Status MSTR Mode 0x29 I2C Data I2C Data 7 I2C Data 6 I2C Data 5 I2C Data 4 I2C Data 3 I2C Data 2 I2C Data 1 I2C Data 0 bbbbbbbb xxxxxxxx 0x40 USB Device Address B Device Device Device Device Device Device Device Device bbbbbbbb Address B Address B Address B Address B Address B Address B Address B Address B Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Enable Bit 6 Bit 5 00000000 0x41 EP B0 Counter Reg- Data 0/1 ister Toggle 0x42 EP B0 Mode Register 0x43 EP B1 Counter Reg- Data 0/1 ister Toggle Data Valid Byte Count Bit 5 0x44 EP B1 Mode Regis- STALL ter - 0x48 Hub Port Connect Status Reserved Reserved Reserved Reserved Port 4 Connect Status Port 3 Connect Status Port 2 Connect Status Port 1 Connect Status ----bbbb 00000000 0x49 Hub Port Enable Reserved Reserved Reserved Reserved Port 4 Enable Port 3 Enable Port 2 Enable Port 1 Enable ----bbbb 00000000 0x4A Hub Port Speed Reserved Reserved Reserved Reserved Port 4 Speed Port 3 Speed Port 2 Speed Port 1 Speed ----bbbb 00000000 0x4B Hub Port Control (Ports 4:1) Port 4 Port 4 Port 3 Port 3 Port 2 Port 2 Port 1 Port 1 bbbbbbbb Control Bit Control Bit Control Bit Control Bit Control Bit Control Bit Control Bit Control Bit 1 0 1 0 1 0 1 0 0x4D Hub Port Suspend Device Remote Wakeup 0x4E Hub Port Resume Status Reserved Reserved Reserved Reserved Resume 4 Resume 3 Resume 2 Resume 1 ----rrrr 00000000 0x4F Hub Port SE0 Status Reserved Reserved Reserved Reserved Port 4 Port 3 Port 2 Port 1 ----rrrr SE0 Sta- SE0 Sta- SE0 Status SE0 Status tus tus 00000000 0x50 Hub Ports Data 00000000 0x51 Hub Port Force Low Force Low Force Low Force Low Force Low Force Low Force Low Force Low Force Low bbbbbbbb D–[3] D+[2] D–[2] D+[1] D–[1] (Ports 4:1) D+[4] D–[4] D+[3] 00000000 0xFF Process Status & Control 00010001 Continue/ Xmit Busy Mode ACK USB Hub 1.024-ms 128 s Interrupt Interrupt Interrupt Enable Enable Enable USB Bus -bbbbbbb RESET Interrupt Enable -0000000 EPB0 Interrupt Enable EPA0 Interrupt Enable ---00000 Addr EPA2 Interrupt Enable EPA1 Interrupt Enable ARB Lost/ Received I2C Restart Stop Enable ---bbbbb bbbbbbbb Data Valid Byte Byte Byte Byte Byte Count Byte bbbbbbbb Count Bit 5 Count Bit 4 Count Bit 3 Count Bit 2 Bit 1 Count Bit 0 Endpoint 0 Endpoint 0 Endpoint 0 ACK SETUP IN OUT Received Received Received - 00000000 Byte Count Bit 4 Byte Count Bit 3 00000000 ACK Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0 b--bbbbb Byte Count Bit 2 Byte Count Byte Bit 1 Count Bit 0 bbbbbbbb 00000000 Reserved Reserved Reserved Port 4 Port 3 Port 2 Port 1 b---bbbb Selective Selective Selective Selective Suspend Suspend Suspend Suspend Document Number: 38-08024 Rev. *G WDR 00000000 Mode Bit 3 Mode Bit 2 Mode Bit 1 Mode Bit 0 bbbbbbbb USB Bus Power-on Suspend Interrupt Reset In- Reset Enable terrupt Sense Reserved Run rbbbbrbb 00000000 00000000 Reserved Reserved Reserved Reserved Port 4 Port 3 Port 2 Port 1 ----rrrr Diff. Data Diff. Data Diff. Data Diff. Data IRQ Pending 00000000 Page 49 of 61 [+] Feedback CY7C66013C, CY7C66113C Sample Schematic Figure 12. Sample Schematic 3.3v Regulator OUT IN GND 2.2 F Vref 2.2 F Vref 1.5K (RUUP) USB-B Vbus DD+ GND 0.01 F Vbus 0.01 F D0– D0+ 22x8(Rext) Vref Vcc 22x2(Rext) SHELL Optional USB-A Vbus D– D+ GND D1– 4.7 nF 250 VAC D1+ USB-A Vbus D– D+ GND D2– XTALO 10M 6.000 MHz D2+ XTALI D3– GND GND Vpp D3+ D4– D4+ 15K(x8) (RUDN) POWER MANAGEMENT Document Number: 38-08024 Rev. *G USB-A Vbus D– D+ GND USB-A Vbus D– D+ GND Page 50 of 61 [+] Feedback CY7C66013C, CY7C66113C Absolute Maximum Ratings Exceeding maximum ratings may impair the useful life of the device. These user guidelines are not tested. Storage Temperature ............................... –65 °C to +150 °C Ambient Temperature with Power Applied...... 0 °C to +70 °C DC Voltage Applied to Outputs in High Z State .................................. –0.5 V to +VCC + 0.5 V Power Dissipation..................................................... 500 mW Static Discharge Voltage ......................................... > 2000 V Latch Up Current .................................................. > 200 mA Supply Voltage on VCC relative to VSS .........–0.5 V to +7.0 V Max Output Sink Current into Port 0, 1, 2, 3, and DAC[1:0] Pins .............................. 60 mA DC Input Voltage .............................. –0.5 V to +VCC + 0.5 V Max Output Sink Current into DAC[7:2] Pins.............. 10 mA Max Output Source Current from Port 1, 2, 3, 4 ........ 30 mA Electrical Characteristics (Fosc = 6 MHz; Operating Temperature = 0 to 70 °C, VCC = 4.0 V to 5.25 V) Parameter Description Conditions Min Max Unit 3.15 3.45 V –0.4 0.4 V – 50 mA General VREF Reference Voltage Vpp Programming Voltage (disabled) ICC VCC Operating Current ISB1 Supply Current—Suspend Mode – 50 A Iref Vref Operating Current No USB Traffic[9] – 10 mA Iil Input Leakage Current Any pin – 1 A 3.3 V ± 5% No GPIO source current USB Interface Vdi Differential Input Sensitivity 0.2 – V Vcm Differential Input Common Mode Range 0.8 2.5 V Vse Single Ended Receiver Threshold 0.8 2.0 V Cin Transceiver Capacitance – 20 pF | (D+)–(D–) | Ilo Hi-Z State Data Line Leakage 0 V < Vin < 3.3 V –10 10 A Rext External USB Series Resistor In series with each USB pin 19 21 RUUP External Upstream USB pull up Resistor 1.5 k ± 5%, D+ to VREG 1.425 1.575 k RUDN External Downstream Pull down Resistors 15 k ± 5%, downstream USB pins 14.25 15.75 k 0 100 ms 2.8 3.6 V Power-on Reset tvccs VCC Ramp Rate Linear ramp 0 V to VCC[10] USB Upstream/Downstream Port VUOH Static Output High 15 k ± 5% to Gnd VUOL Static Output Low 1.5 k ± 5% to VREF ZO USB Driver Output Impedance Including Rext Resistor – 0.3 V 28 44 8.0 24.0 k General Purpose I/O (GPIO) Rup pull up Resistance (typical 14 k VITH Input Threshold Voltage All ports, LOW to HIGH edge 20% 40% VCC VH Input Hysteresis Voltage All ports, HIGH to LOW edge 2% 8% VCC VOL Port 0,1,2,3 Output Low Voltage IOL = 3 mA IOL = 8 mA – 0.4 2.0 V V Notes 9. Add 18 mA per driven USB cable (upstream or downstream). This is based on transitions every two full speed bit times on average. 10. Power on Reset occurs whenever the voltage on VCC is below approximately 2.5 V. Document Number: 38-08024 Rev. *G Page 51 of 61 [+] Feedback CY7C66013C, CY7C66113C Electrical Characteristics (Fosc = 6 MHz; Operating Temperature = 0 to 70 °C, VCC = 4.0 V to 5.25 V) (continued) Parameter VOH Description Conditions Output High Voltage IOH = 1.9 mA (all ports 0,1,2,3) Min Max Unit 2.4 – V 8.0 24.0 k DAC Interface Rup DAC Pull Up Resistance (typical 14 k Isink0(0) DAC[7:2] Sink Current (0) Vout = 2.0 V DC 0.1 0.3 mA Isink0(F) DAC[7:2] Sink Current (F) Vout = 2.0 V DC 0.5 1.5 mA Isink1(0) DAC[1:0] Sink Current (0) Vout = 2.0 V DC 1.6 4.8 mA Isink1(F) DAC[1:0] Sink Current (F) Vout = 2.0 V DC 8 24 mA Irange Programmed Isink Ratio: max/min Vout = 2.0 V DC[11] 4 6 Tratio Tracking Ratio DAC[1:0] to DAC[7:2] Vout = 2.0 V[12] 14 22 IsinkDAC DAC Sink Current Vout = 2.0 V DC 1.6 4.8 mA Ilin Differential Nonlinearity DAC Port[13] 0.6 LSB Switching Characteristics (FOSC = 6.0 MHz) Parameter Description Min Max Unit 6 ± 0.25% – MHz 166.25 167.08 ns Clock Source fOSC Clock Rate tcyc Clock Period tCH Clock HIGH time 0.45 tCYC – ns tCL Clock LOW time 0.45 tCYC – ns 4 20 ns USB Full Speed Signaling[14] trfs Transition Rise Time tffs Transition Fall Time 4 20 ns trfmfs Rise/Fall Time Matching; (tr/tf) 90 111 % tdratefs Full Speed Date Rate 12 ± 0.25% – Mb/s – 0.8 s DAC Interface tsink Current Sink Response Time HAPI Read Cycle Timing tRD Read Pulse Width 15 – ns tOED OE LOW to Data Valid[15, 16] – 40 ns – 20 ns 0 60 ns Z[16] tOEZ OE HIGH to Data High tOEDR OE LOW to Data_Ready Deasserted[15, 16] Notes 11. Irange: Isinkn(15)/Isinkn(0) for the same pin. 12. Tratio = Isink1[1:0](n)/Isink0[7:2](n) for the same n, programmed. 13. Ilin measured as largest step size vs. nominal according to measured full scale and zero programmed values. 14. Per Table 7-6 of revision 1.1 of USB specification. 15. For 25 pF load. 16. Assumes chip select CS is asserted (LOW). Document Number: 38-08024 Rev. *G Page 52 of 61 [+] Feedback CY7C66013C, CY7C66113C Switching Characteristics (FOSC = 6.0 MHz) Parameter Description Min Max Unit HAPI Write Cycle Timing tWR Write Strobe Width 15 – ns tDSTB Data Valid to STB HIGH (Data Setup Time)[16] 5 – ns tSTBZ STB HIGH to Data High Z (Data Hold Time) [16] 15 – ns tSTBLE STB LOW to Latch_Empty Deasserted[15, 16] 0 50 ns 8.192 14.336 ms Timer Signals twatch WDT Period Figure 13. Clock Timing tCYC tCH CLOCK tCL Figure 14. USB Data Signal Timing tr tr D 90% D Document Number: 38-08024 Rev. *G 10% 90% 10% Page 53 of 61 [+] Feedback CY7C66013C, CY7C66113C Figure 15. HAPI Read by External Interface from USB Microcontroller Interrupt Generated Int CS (P2.6, input) tRD OE (P2.5, input) DATA (output) D[23:0] tOED STB (P2.4, input) tOEZ tOEDR (Ready) DReadyPin (P2.3, output) (Shown for DRDY Polarity=0) Internal Write Internal Addr Document Number: 38-08024 Rev. *G Port0 Page 54 of 61 [+] Feedback CY7C66013C, CY7C66113C Figure 16. HAPI Write by External Device to USB Microcontroller Interrupt Generated Int CS (P2.6, input) tWR STB (P2.4, input) tSTBZ DATA (input) D[23:0] tDSTB OE (P2.5, input) tSTBLE LEmptyPin (P2.2, output) (Shown for LEMPTY Polarity=0) (not empty) Internal Read Internal Addr Port0 Ordering Information Ordering Code PROM Size Package Type Operating Range CY7C66013C-PVXC 8 KB 48-pin (300-Mil) SSOP Commercial CY7C66113C-PVXC 8 KB 56-pin (300-Mil) SSOP Commercial CY7C66113C-PVXCT 8 KB 56-pin (300-Mil) SSOP Commercial CY7C66113C-XC 8 KB Die Commercial CY7C66113C-LTXC 8 KB 56-pin QFN Commercial CY7C66113C-LTXCT 8 KB 56-pin QFN Commercial Ordering Code Definitions CY 7C66X13 - X X X X X X = blank or T (blank = Bulk; T = Tape and Reel) X = Temperature Grade = C or A (C = Commercial grade; A = Automotive grade) X = Pb-free X = V or T Package Type: X = P or L P = 48-pin SSOP or 56-pin SSOP; L = 56-pin QFN Part Identifier: 7C66X13 = 7C66013 or 7C66113 Company ID: CY = Cypress Document Number: 38-08024 Rev. *G Page 55 of 61 [+] Feedback CY7C66013C, CY7C66113C Package Diagrams Figure 17. 48-pin Shrunk Small Outline Package O48 51-85061-*D Figure 18. 56-pin Shrunk Small Outline Package O56 51-85062-*D Document Number: 38-08024 Rev. *G Page 56 of 61 [+] Feedback CY7C66013C, CY7C66113C Figure 19. 56-QFN 8 × 8 × 1.0 mm EPad 4.5 × 5.2 mm 001-53450 *B Document Number: 38-08024 Rev. *G Page 57 of 61 [+] Feedback CY7C66013C, CY7C66113C Quad Flat Package No Leads (QFN) Package Design Notes Electrical contact of the part to the Printed Circuit Board (PCB) is made by soldering the leads on the bottom surface of the package to the PCB. Hence, special attention is required to the heat transfer area below the package to provide a good thermal bond to the circuit board. A Copper (Cu) fill is to be designed into the PCB as a thermal pad under the package. Heat is transferred from the FX1 through the device’s metal paddle on the bottom side of the package. Heat from here, is conducted to the PCB at the thermal pad. It is then conducted from the thermal pad to the PCB inner ground plane by a 5 x 5 array of via. A via is a plated through hole in the PCB with a finished diameter of 13 mil. The QFN’s metal die paddle must be soldered to the PCB’s thermal pad. Solder mask is placed on the board top side over each via to resist solder flow into the via. The mask on the top side also minimizes outgassing during the solder reflow process. For further information on this package design please refer to the application note Surface Mount Assembly of AMKOR’s MicroLeadFrame (MLF) Technology. This application note can be downloaded from AMKOR’s website from the following URL http://www.amkor.com/products/notes_papers/MLF_AppNote_ 0902.pdf. The application note provides detailed information on board mounting guidelines, soldering flow, rework process, etc. Figure 20 displays a cross sectional area underneath the package. The cross section is of only one via. The thickness of the solder paste template should be 5 mil. It is recommended that “No Clean” type 3 solder paste is used for mounting the part. Nitrogen purge is recommended during reflow. Figure 21 is a plot of the solder mask pattern. This pad is thermally connected and is not electrically connected inside the chip. To minimize EMI, this pad should be connected to the ground plane of the circuit board. Figure 20. Cross Section of the Area Underneath the QFN Package 0.017” dia Solder Mask Cu Fill Cu Fill PCB Material Via hole for thermally connecting the QFN to the circuit board ground plane. 0.013” dia PCB Material This figure only shows the top three layers of the circuit board: Top Solder, PCB Dielectric, and the Ground Plane Figure 21. Plot of the Solder Mask (White Area) Document Number: 38-08024 Rev. *G Page 58 of 61 [+] Feedback CY7C66013C, CY7C66113C Acronyms Document Conventions The following table lists the acronyms that are used in this document. Units of Measure Acronym CPU Description The following table lists all the abbreviations used to measure the PSoC devices. central processing unit Numeric Naming EMI electromagnetic interference FIFO First In, First Out GPIO general purpose input/output HAPI Hardware Assisted Parallel Interface Hexadecimal numbers are represented with all letters in uppercase with an appended lowercase 'h' (for example, '14h' or '3Ah'). Hexadecimal numbers may also be represented by a '0x' prefix, the C coding convention. Binary numbers have an appended lowercase 'b' (for example, 01010100b' or '01000011b'). Numbers not indicated by an 'h', 'b', or 0x are decimal. I/O Input/Output LED light-emitting diode LSB least significant bit MSB most significant bit PCB printed circuit board PLL phase-locked loop POR power on reset QFN Quad Flat No leads Symbol Unit of Measure °C degree Celsius cm centi meter mm milli meter k kilo ohms µA micro Amperes PROM programmable read only memory RAM random access memory µs micro seconds SIE Serial Interface Engine mA milli Amperes SSOP Shrink small-outline package ms milli seconds Universal Serial Bus ns nano seconds ohms pF pico Farad MHz Mega Hertz V Volts mW milli Watts USB Document Number: 38-08024 Rev. *G Page 59 of 61 [+] Feedback CY7C66013C, CY7C66113C Document History Page Document Title: CY7C66013C, CY7C66113C Full Speed USB (12 Mbps) Peripheral Controller with Integrated Hub Document Number: 38-08024 Rev. ECN No. Submission Date Orig. of Change Description of Change ** 114525 3/27/02 DSG Change from Spec number: 38-00591 to 38-08024 *A 124768 03/20/03 MON Added register bit definitions; Added default bit state of each register. Corrected the Schematic (location of the pull-up on D+). Added register summary. Removed information on the availability of the part in PDIP package. Modified Table 51 and provided more explanation regarding locking/unlocking mechanism of the mode register. Removed any information regarding the speed detect bit in Hub Port Speed register being set by hardware. *B 417632 See ECN BHA Updated part number and ordering information. Added QFN Package Drawing and Design Notes. Corrected bit names in Figures 9-3, 9-4, 9-5, 9-8, 9-9, 9-10, 10-5, 16-1, 18-1, 18-2, 18-3, 18-6, 18-7, 18-9, 18-10. Removed Hub Ports Force Low register address 0x52. Added HAPI to Interrupt Vector Number 11 in Table 16-1. Corrected bit names in Section 21.0. Corrected Units in Table 24.0 for RUUP, RUDN, REXT, and ZO. Added DIE diagram and related information. Added HAPI to GPIO interrupt vector in Table 5-1 and figure 16-3 *C 1825466 See ECN TLY/PYRS Changed Title from "CY7C66013, CY7C66113 Full Speed USB (12 Mbps) Peripheral Controller with Integrated Hub" to "CY7C66013C, CY7C66113C Full Speed USB (12 Mbps) Peripheral Controller with Integrated Hub" Changed package description for CY7C66013C and CY7C66113C from -PVC to -PVXC *D 2720540 06/18/09 DPT/AESA Added 56 QFN 8x8x1 mm package diagram and ordering information *E 2896318 03/18/10 AESA Removed Part CY7C66113C-LFXC. Updated all package diagrams. *F 3057657 10/13/10 AJHA Added “Not recommended for new designs” watermark in the PDF. No technical or content updates. *G 3177081 02/18/2011 NXZ Added Ordering Code Definitions. Updated Package Diagrams. Added Acronyms and Units of Measure. Updated in new template. Document Number: 38-08024 Rev. *G Page 60 of 61 [+] Feedback CY7C66013C, CY7C66113C Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing cypress.com/go/memory cypress.com/go/image PSoC Touch Sensing cypress.com/go/psoc cypress.com/go/touch USB Controllers Wireless/RF cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2002-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 38-08024 Rev. *G Revised March 1, 2011 Page 61 of 61 All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback