CYPRESS CY7C1471BV33

CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
72-Mbit (2 M × 36/4 M × 18/1 M × 72)
Flow-Through SRAM with
NoBL™ Architecture
Features
Functional Description
■
No bus latency™ (NoBL™) architecture eliminates dead cycles
between write and read cycles
■
Supports up to 133 MHz bus operations with zero wait states
■
Data is transferred on every clock
■
Pin compatible and functionally equivalent to ZBT™ devices
■
Internally self timed output buffer control to eliminate the need
to use OE
■
Registered inputs for flow through operation
The CY7C1471BV33, CY7C1473BV33, and CY7C1475BV33
are 3.3 V, 2M × 36/4M × 18/1M × 72 synchronous flow through
burst SRAMs designed specifically to support unlimited true
back-to-back read or write operations without the insertion of
wait states. The CY7C1471BV33, CY7C1473BV33, and
CY7C1475BV33 are equipped with the advanced No Bus
Latency (NoBL) logic. NoBL™ is required to enable consecutive
read or write operations with data being transferred on every
clock cycle. This feature dramatically improves the throughput of
data through the SRAM, especially in systems that require
frequent write-read transitions.
■
Byte write capability
■
3.3 V/2.5 V I/O supply (VDDQ)
■
Fast clock-to-output times
❐ 6.5 ns (for 133 MHz device)
■
Clock enable (CEN) pin to enable clock and suspend operation
■
Synchronous self-timed writes
■
Asynchronous output enable (OE)
■
CY7C1471BV33, CY7C1473BV33 available in
JEDEC-standard Pb-free 100-pin thin quad flat pack (TQFP),
Pb-free and non-Pb-free 165-ball fine-pitch ball grid array
(FBGA) package. CY7C1475BV33 available in Pb-free and
non-Pb-free 209-ball FBGA package
■
Three chip enables (CE1, CE2, CE3) for simple depth
expansion
■
Automatic power-down feature available using ZZ mode or CE
deselect
■
IEEE 1149.1 JTAG boundary scan compatible
■
Burst capability—linear or interleaved burst order
■
Low standby power
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock input is qualified by the
Clock Enable (CEN) signal, which when deasserted suspends
operation and extends the previous clock cycle. Maximum
access delay from the clock rise is 6.5 ns (133 MHz device).
Write operations are controlled by two or four Byte Write Select
(BWX) and a Write Enable (WE) input. All writes are conducted
with on-chip synchronous self timed write circuitry.
Three synchronous chip enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. To avoid bus contention,
the output drivers are synchronously tri-stated during the data
portion of a write sequence.
Selection Guide
Description
133 MHz
117 MHz
Unit
6.5
8.5
ns
Maximum access time
Maximum operating current
305
275
mA
Maximum CMOS standby current
120
120
mA
Cypress Semiconductor Corporation
Document Number: 001-15029 Rev. *E
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised June 30, 2011
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Logic Block Diagram – CY7C1471BV33 (2 M × 36)
ADDRESS
REGISTER
A0, A1, A
A1
D1
A0
D0
MODE
CLK
CEN
CE
C
ADV/LD
C
BURST
LOGIC
Q1 A1'
A0'
Q0
WRITE ADDRESS
REGISTER
ADV/LD
BW A
WRITE
DRIVERS
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
BW B
BW C
MEMORY
ARRAY
S
E
N
S
E
A
M
P
S
BW D
WE
INPUT
REGISTER
OE
CE1
CE2
CE3
D
A
T
A
S
T
E
E
R
I
N
G
O
U
T
P
U
T
B
U
F
F
E
R
S
DQs
DQP A
DQP B
DQP C
DQP D
E
E
READ LOGIC
SLEEP
CONTROL
ZZ
Logic Block Diagram – CY7C1473BV33 (4 M × 18)
ADDRESS
REGISTER
A0, A1, A
A1
D1
A0
D0
MODE
CLK
CEN
CE
C
ADV/LD
C
BURST
LOGIC
A1'
Q1
A0'
Q0
WRITE ADDRESS
REGISTER
ADV/LD
BW A
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
BW B
WRITE
DRIVERS
MEMORY
ARRAY
S
E
N
S
E
A
M
P
S
WE
OE
CE1
CE2
CE3
D
A
T
A
S
T
E
E
R
I
N
G
O
U
T
P
U
T
B
U
F
F
E
R
S
DQs
DQP A
DQP B
E
INPUT
E
REGISTER
READ LOGIC
ZZ
Document Number: 001-15029 Rev. *E
SLEEP
CONTROL
Page 2 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Logic Block Diagram – CY7C1475BV33 (1 M × 72)
A0, A1, A
ADDRESS
REGISTER 0
MODE
CLK
ADV/LD
C
C
A1
A1'
D1
Q1
A0
A0'
D0 BURST Q0
LOGIC
CEN
WRITE ADDRESS
REGISTER 2
WRITE ADDRESS
REGISTER 1
ADV/LD
BW a
BW b
BW c
BW d
BW e
BW f
BW g
BW h
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
S
E
N
S
E
A
M
P
S
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
D
A
T
A
S
T
E
E
R
I
N
G
E
O
U
T
P
U
T
B
U
F
F
E
R
S
E
DQ s
DQ Pa
DQ Pb
DQ Pc
DQ Pd
DQ Pe
DQ Pf
DQ Pg
DQ Ph
WE
INPUT
E
REGISTER 1
OE
CE1
CE2
CE3
ZZ
INPUT
E
REGISTER 0
READ LOGIC
Sleep Control
Document Number: 001-15029 Rev. *E
Page 3 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Contents
Pin Configuration ............................................................. 5
Pin Definitions .................................................................. 9
Functional Overview ...................................................... 10
Single Read Accesses .............................................. 10
Burst Read Accesses ................................................ 10
Single Write Accesses ............................................... 11
Burst Write Accesses ................................................ 11
Sleep Mode ............................................................... 11
Interleaved Burst Address Table .................................. 11
Linear Burst Address Table ........................................... 11
ZZ Mode Electrical Characteristics ............................... 11
Truth Table ................................................................ 12
Truth Table for Read/Write ........................................ 13
Truth Table for Read/Write ........................................ 13
Truth Table for Read/Write ........................................ 13
IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 14
Disabling the JTAG Feature ...................................... 14
Test Access Port (TAP) ............................................. 14
PERFORMING A TAP RESET .................................. 14
TAP REGISTERS ...................................................... 14
TAP Instruction Set ................................................... 15
TAP Controller State Diagram ....................................... 16
TAP Controller Block Diagram ..................................... 17
3.3-V TAP AC Test Conditions ...................................... 18
3.3-V TAP AC Output Load Equivalent ......................... 18
2.5-V TAP AC Test Conditions ...................................... 18
2.5-V TAP AC Output Load Equivalent ......................... 18
TAP DC Electrical Characteristics and
Document Number: 001-15029 Rev. *E
Operating Conditions ..................................................... 18
TAP AC Switching Characteristics ............................... 19
TAP Timing ...................................................................... 19
Identification Register Definitions ................................ 20
Scan Register Sizes ....................................................... 20
Identification Codes ....................................................... 20
Boundary Scan Exit Order (2 M × 36) ........................... 21
Boundary Scan Exit Order (4 M × 18) ........................... 21
Boundary Scan Exit Order (1 M × 72) ........................... 22
Maximum Ratings ........................................................... 23
Operating Range ............................................................. 23
Electrical Characteristics ............................................... 23
Capacitance .................................................................... 24
Thermal Resistance ........................................................ 24
Switching Characteristics .............................................. 25
Switching Waveforms .................................................... 26
Ordering Information ...................................................... 29
Ordering Code Definitions ........................................ 29
Package Diagrams .......................................................... 30
Reference Information ................................................... 33
Acronyms .................................................................. 33
Document Conventions ................................................. 33
Document History Page ................................................ 34
Sales, Solutions, and Legal Information ...................... 35
Worldwide Sales and Design Support ....................... 35
Products .................................................................... 35
PSoC Solutions ......................................................... 35
Page 4 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Pin Configuration
A
41
42
43
44
45
46
47
48
49
50
VDD
A
A
A
A
A
A
A
A
A
A0
40
37
A1
VSS
36
39
35
A
NC/144M
34
A
38
33
A
NC/288M
32
A
Document Number: 001-15029 Rev. *E
81
A
82
83
A
A
84
ADV/LD
90
85
VSS
91
OE
VDD
92
CEN
CE3
93
87
BWA
94
WE
BWB
95
88
BWC
96
CLK
BWD
97
89
CE1
CE2
A
98
86
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
CY7C1471BV33
31
BYTE D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
BYTE C
DQPC
DQC
DQC
VDDQ
VSS
DQC
DQC
DQC
DQC
VSS
VDDQ
DQC
DQC
NC
VDD
NC
VSS
DQD
DQD
VDDQ
VSS
DQD
DQD
DQD
DQD
VSS
VDDQ
DQD
DQD
DQPD
99
100
A
Figure 1. 100-pin TQFP Pinout – CY7C1471BV33 (2 M × 36)
DQPB
DQB
DQB
VDDQ
VSS
DQB
DQB
DQB
DQB
VSS
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSS
DQA
DQA
DQA
DQA
VSS
VDDQ
DQA
DQA
DQPA
BYTE B
BYTE A
Page 5 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Pin Configuration (continued)
A
41
42
43
44
45
46
47
48
49
50
VDD
A
A
A
A
A
A
A
A
A
A0
40
37
A1
VSS
36
39
35
A
NC/144M
34
A
38
33
A
NC/288M
32
A
Document Number: 001-15029 Rev. *E
81
A
82
A
83
A
84
ADV/LD
85
OE
CEN
VSS
90
87
VDD
91
WE
CE3
92
88
BWA
93
CLK
BWB
94
89
NC
95
NC
CE2
97
96
CE1
A
98
86
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
CY7C1473BV33
31
BYTE B
VDDQ
VSS
NC
NC
DQB
DQB
VSS
VDDQ
DQB
DQB
NC
VDD
NC
VSS
DQB
DQB
VDDQ
VSS
DQB
DQB
DQPB
NC
VSS
VDDQ
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
NC
NC
NC
99
100
A
Figure 2. 100-pin TQFP Pinout – CY7C1473BV33 (4 M × 18)
A
NC
NC
VDDQ
VSS
NC
DQPA
DQA
DQA
VSS
VDDQ
DQA
DQA
VSS
NC
VDD
ZZ
BYTE A
DQA
DQA
VDDQ
VSS
DQA
DQA
NC
NC
VSS
VDDQ
NC
NC
NC
Page 6 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Pin Configuration (continued)
165-ball FBGA (15 × 17 × 1.4 mm) Pinout
CY7C1471BV33 (2 M × 36)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
A
CE1
BWC
BWB
CE3
CEN
ADV/LD
A
A
NC
NC/1G
A
CE2
BWD
BWA
CLK
WE
OE
A
A
NC
DQPC
NC
DQC
VDDQ
VSS
VDD
VSS
VSS
VSS
NC
DQPB
VSS
VSS
VSS
VSS
VDD
VDDQ
DQC
VDDQ
DQB
DQB
R
VDDQ
DQC
DQC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQB
DQB
DQC
DQC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQB
DQB
DQC
NC
DQD
DQC
NC
DQD
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
NC
VDDQ
DQB
NC
DQA
DQB
ZZ
DQA
DQD
DQD
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
DQD
DQD
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
DQD
DQPD
DQD
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
VDD
VSS
VDDQ
VDDQ
DQA
NC
DQA
DQPA
NC/144M
A
A
A
TDI
NC
A1
VSS
NC
TDO
A
A
A
NC/288M
MODE
A
A
A
TMS
A0
TCK
A
A
A
A
CY7C1473BV33 (4 M × 18)
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
1
A
CE1
BWB
NC
CE3
CEN
ADV/LD
A
A
A
NC/1G
A
CE2
NC
BWA
CLK
WE
OE
A
A
NC
NC
NC
NC
DQB
VDDQ
VSS
VDD
VSS
VSS
VSS
VSS
VDD
VDDQ
NC
NC
DQPA
VSS
VSS
VSS
VDDQ
VDDQ
NC
DQB
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQA
R
DQA
NC
DQB
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQA
NC
NC
DQB
DQB
NC
NC
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
NC
VDDQ
NC
NC
DQA
DQA
ZZ
NC
DQB
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
DQB
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
DQB
DQPB
NC
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC/144M
A
A
A
MODE
A
A
A
Document Number: 001-15029 Rev. *E
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQA
NC
NC
NC
TDI
NC
A1
TDO
A
A
A
NC/288M
TMS
A0
TCK
A
A
A
A
Page 7 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Pin Configuration (continued)
209-ball FBGA (14 × 22 × 1.76 mm) Pinout
CY7C1475BV33 (1 M × 72)
1
2
3
4
5
6
7
8
9
10
11
A
DQg
DQg
A
CE2
A
ADV/LD
A
CE3
A
DQb
DQb
B
DQg
DQg
BWSc
BWSg
NC
WE
A
BWSb
BWSf
DQb
DQb
C
DQg
DQg
BWSh
BWSd NC/576M
CE1
NC
BWSe
BWSa
DQb
DQb
D
DQg
DQg
VSS
NC
NC/1G
OE
NC
NC
VSS
DQb
DQb
E
DQPg
DQPc
VDDQ
VDDQ
VDD
VDD
VDD
VDDQ
VDDQ
DQPf
DQPb
F
DQc
DQc
VSS
VSS
VSS
NC
VSS
VSS
VSS
DQf
DQf
G
DQc
DQc
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQf
DQf
H
DQc
DQc
VSS
VSS
VSS
NC
VSS
VSS
VSS
DQf
DQf
VDDQ
DQf
DQf
J
DQc
DQc
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
K
NC
NC
CLK
NC
VSS
CEN
VSS
NC
NC
NC
NC
L
DQh
DQh
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQa
DQa
M
DQh
DQh
VSS
VSS
VSS
NC
VSS
VSS
VSS
DQa
DQa
N
DQh
DQh
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQa
DQa
P
DQh
DQh
VSS
VSS
VSS
ZZ
VSS
VSS
VSS
DQa
DQa
VDDQ
VDD
VDD
VDD
VDDQ
VDDQ
DQPa
DQPe
R
DQPd
DQPh
VDDQ
T
DQd
DQd
VSS
NC
NC
MODE
NC
NC
VSS
DQe
DQe
A
A
A
A
NC/288M
DQe
DQe
U
DQd
DQd
NC/144M
A
V
DQd
DQd
A
A
A
A1
A
A
A
DQe
DQe
W
DQd
DQd
TMS
TDI
A
A0
A
TDO
TCK
DQe
DQe
Document Number: 001-15029 Rev. *E
Page 8 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Pin Definitions
Name
I/O
Description
A0, A1, A
InputSynchronous
Address inputs used to select one of the address locations. Sampled at the rising edge of
the CLK. A[1:0] is fed to the two-bit burst counter.
BWA, BWB,
BWC, BWD,
BWE, BWF,
BWG, BWH
InputSynchronous
Byte write inputs, active LOW. Qualified with WE to conduct writes to the SRAM. Sampled
on the rising edge of CLK.
WE
InputSynchronous
Write enable input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW.
This signal must be asserted LOW to initiate a write sequence.
ADV/LD
InputSynchronous
Advance/load input. Advances the on-chip address counter or loads a new address. When
HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new
address can be loaded into the device for an access. After deselection, drive ADV/LD LOW to
load a new address.
CLK
InputClock
Clock input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN.
CLK is only recognized if CEN is active LOW.
CE1
InputSynchronous
Chip enable 1 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction
with CE2 and CE3 to select or deselect the device.
CE2
InputSynchronous
Chip enable 2 input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE3 to select or deselect the device.
CE3
InputSynchronous
Chip enable 3 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE2 to select or deselect the device.
OE
InputAsynchronous
Output enable, asynchronous input, active LOW. Combined with the synchronous logic
block inside the device to control the direction of the I/O pins. When LOW, the I/O pins are
enabled to behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as input
data pins. OE is masked during the data portion of a write sequence, during the first clock when
emerging from a deselected state, and when the device is deselected.
CEN
InputSynchronous
Clock enable input, active LOW. When asserted LOW the clock signal is recognized by the
SRAM. When deasserted HIGH the clock signal is masked. Because deasserting CEN does
not deselect the device, CEN can be used to extend the previous cycle when required.
ZZ
InputAsynchronous
ZZ “Sleep” input. This active HIGH input places the device in a non-time critical “sleep”
condition with data integrity preserved. During normal operation, this pin must be LOW or left
floating. ZZ pin has an internal pull-down.
DQs
I/OSynchronous
Bidirectional data I/O lines. As inputs, they feed into an on-chip data register that is triggered
by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by the addresses presented during the previous clock rise of the read cycle. The
direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs.
When HIGH, DQs and DQPX are placed in a tri-state condition.The outputs are automatically
tri-stated during the data portion of a write sequence, during the first clock when emerging from
a deselected state, and when the device is deselected, regardless of the state of OE.
DQPX
I/OSynchronous
Bidirectional data parity I/O lines. Functionally, these signals are identical to DQs. During
write sequences, DQPX is controlled by BWX correspondingly.
MODE
Input Strap Pin
Mode input. Selects the burst order of the device. When tied to Gnd selects linear burst
sequence. When tied to VDD or left floating selects interleaved burst sequence.
VDD
Power Supply
Power supply inputs to the core of the device.
VDDQ
VSS
I/O Power Supply Power supply for the I/O circuitry.
Ground
Ground for the device.
Document Number: 001-15029 Rev. *E
Page 9 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Pin Definitions (continued)
Name
TDO
I/O
Description
JTAG serial
output
Synchronous
Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the JTAG
feature is not used, this pin must be left unconnected. This pin is not available on TQFP
packages.
TDI
JTAG serial input Serial data-in to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is
Synchronous not used, this pin can be left floating or connected to VDD through a pull-up resistor. This pin is
not available on TQFP packages.
TMS
JTAG serial input Serial data-in to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is
Synchronous not used, this pin can be disconnected or connected to VDD. This pin is not available on TQFP
packages.
TCK
JTAG
-Clock
NC
–
Clock input to the JTAG circuitry. If the JTAG feature is not used, this pin must be connected
to VSS. This pin is not available on TQFP packages.
No connects. Not internally connected to the die. 144M, 288M, 576M, and 1G are address
expansion pins and are not internally connected to the die.
Functional Overview
The CY7C1471BV33, CY7C1473BV33, and CY7C1475BV33
are synchronous flow through burst SRAMs designed
specifically to eliminate wait states during write-read transitions.
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock signal is qualified with the
Clock Enable input signal (CEN). If CEN is HIGH, the clock signal
is not recognized and all internal states are maintained. All
synchronous operations are qualified with CEN. Maximum
access delay from the clock rise (tCDV) is 6.5 ns (133 MHz
device).
Accesses may be initiated by asserting all three chip enables
(CE1, CE2, CE3) active at the rising edge of the clock. If (CEN)
is active LOW and ADV/LD is asserted LOW, the address
presented to the device is latched. The access can either be a
read or write operation, depending on the status of the Write
Enable (WE). Byte Write Select (BWX) can be used to conduct
Byte Write operations.
Write operations are qualified by the Write Enable (WE). All
writes are simplified with on-chip synchronous self timed write
circuitry.
Three synchronous chip enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) simplify depth expansion. All
operations (reads, writes, and deselects) are pipelined. ADV/LD
must be driven LOW after the device is deselected to load a new
address for the next operation.
Document Number: 001-15029 Rev. *E
Single Read Accesses
A read access is initiated when these conditions are satisfied at
clock rise:
■
CEN is asserted LOW
■
CE1, CE2, and CE3 are ALL asserted active
■
WE is deasserted HIGH
■
ADV/LD is asserted LOW
The address presented to the address inputs is latched into the
Address Register and presented to the memory array and control
logic. The control logic determines that a read access is in
progress and allows the requested data to propagate to the
output buffers. The data is available within 6.5 ns (133 MHz
device) provided OE is active LOW. After the first clock of the
read access, the output buffers are controlled by OE and the
internal control logic. OE must be driven LOW to drive out the
requested data. On the subsequent clock, another operation
(read/write/deselect) can be initiated. When the SRAM is
deselected at clock rise by one of the chip enable signals, output
is tri-stated immediately.
Burst Read Accesses
The CY7C1471BV33, CY7C1473BV33, and CY7C1475BV33
have an on-chip burst counter that enables the user to supply a
single address and conduct up to four reads without reasserting
the address inputs. ADV/LD must be driven LOW to load a new
address into the SRAM, as described in the Single Read Access
section. The sequence of the burst counter is determined by the
MODE input signal. A LOW input on MODE selects a linear burst
mode, a HIGH selects an interleaved burst sequence. Both burst
counters use A0 and A1 in the burst sequence, and wrap around
when incremented sufficiently. A HIGH input on ADV/LD
increments the internal burst counter regardless of the state of
chip enable inputs or WE. WE is latched at the beginning of a
burst cycle. Therefore, the type of access (read or write) is
maintained throughout the burst sequence.
Page 10 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Single Write Accesses
Write accesses are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are all asserted active, and (3) WE is asserted LOW.
The address presented to the address bus is loaded into the
Address Register. The Write signals are latched into the Control
Logic block. The data lines are automatically tri-stated
regardless of the state of the OE input signal. This allows the
external logic to present the data on DQs and DQPX.
On the next clock rise the data presented to DQs and DQPX (or
a subset for Byte Write operations, see section Truth Table for
Read/Write on page 13 for details), input is latched into the
device and the write is complete. Additional accesses
(read/write/deselect) can be initiated on this cycle.
The data written during the write operation is controlled by BWX
signals. The CY7C1471BV33, CY7C1473BV33, and
CY7C1475BV33 provide Byte Write capability that is described
in the section Truth Table for Read/Write on page 13. The input
WE with the selected BWX input selectively writes to only the
desired bytes. Bytes not selected during a Byte Write operation
remain unaltered. A synchronous self timed write mechanism is
provided to simplify the write operations. Byte write capability is
included to greatly simplify read/modify/write sequences, which
can be reduced to simple byte write operations.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
and the completion of the operation is not guaranteed. The
device must be deselected before entering the “sleep” mode.
CE1, CE2, and CE3, must remain inactive for the duration of
tZZREC after the ZZ input returns LOW.
Interleaved Burst Address Table
(MODE = Floating or VDD)
Because the CY7C1471BV33, CY7C1473BV33, and
CY7C1475BV33 are common I/O devices, do not drive data into
the device when the outputs are active. The Output Enable (OE)
can be deasserted HIGH before presenting data to the DQs and
DQPX inputs. Doing so tri-states the output drivers. As a safety
precaution, DQs and DQPX are automatically tri-stated during
the data portion of a write cycle, regardless of the state of OE.
Burst Write Accesses
subsequent clock rise, the chip enables (CE1, CE2, and CE3)
and WE inputs are ignored and the burst counter is incremented.
Drive the correct BWX inputs in each cycle of the burst write to
write the correct bytes of data.
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Linear Burst Address Table
(MODE = GND)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
The CY7C1471BV33, CY7C1473BV33, and CY7C1475BV33
have an on-chip burst counter that enables the user to supply a
single address and conduct up to four write operations without
reasserting the address inputs. ADV/LD must be driven LOW to
load the initial address, as described in section Single Write
Accesses on page 11. When ADV/LD is driven HIGH on the
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
Min
Max
Unit
IDDZZ
Sleep mode standby current
ZZ > VDD – 0.2 V
–
120
mA
tZZS
Device operation to ZZ
ZZ > VDD – 0.2 V
–
2tCYC
ns
tZZREC
ZZ recovery time
ZZ < 0.2 V
2tCYC
–
ns
tZZI
ZZ active to sleep current
This parameter is sampled
–
2tCYC
ns
tRZZI
ZZ Inactive to exit sleep current
This parameter is sampled
0
–
ns
Document Number: 001-15029 Rev. *E
Page 11 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Truth Table
The truth table for CY7C1471BV33, CY7C1473BV33, and CY7C1475BV33 follows.[1, 2, 3, 4, 5, 6, 7]
Operation
Address CE CE
1
2 CE3 ZZ
Used
ADV/LD
WE
BWX
OE
CEN
CLK
DQ
Deselect cycle
None
H
X
X
L
L
X
X
X
L
L->H
Tri-state
Deselect cycle
None
X
X
H
L
L
X
X
X
L
L->H
Tri-state
Deselect cycle
None
X
L
X
L
L
X
X
X
L
L->H
Tri-state
Continue deselect cycle
None
X
X
X
L
H
X
X
X
L
L->H
Tri-state
External
L
H
L
L
L
H
X
L
L
L->H Data out (Q)
Next
X
X
X
L
H
X
X
L
L
L->H Data out (Q)
External
L
H
L
L
L
H
X
H
L
L->H
Tri-state
Next
X
X
X
L
H
X
X
H
L
L->H
Tri-state
External
L
H
L
L
L
L
L
X
L
L->H
Data in (D)
Write cycle
(continue burst)
Next
X
X
X
L
H
X
L
X
L
L->H
Data in (D)
NOP/Write abort
(begin burst)
None
L
H
L
L
L
L
H
X
L
L->H
Tri-state
Write abort
(continue burst)
Next
X
X
X
L
H
X
H
X
L
L->H
Tri-state
Read cycle
(begin burst)
Read cycle
(continue burst)
NOP/Dummy read
(begin burst)
Dummy read
(continue burst)
Write cycle
(begin burst)
Ignore clock edge (stall)
Sleep mode
Current
X
X
X
L
X
X
X
X
H
L->H
–
None
X
X
X
H
X
X
X
X
X
X
Tri-state
Notes
1. X = “Don't Care.” H = Logic HIGH, L = Logic LOW. BWX = L signifies at least one Byte Write Select is active, BWX = Valid signifies that the desired Byte Write Selects
are asserted, see section Truth Table for Read/Write on page 13 for details.
2. Write is defined by BWX, and WE. See section Truth Table for Read/Write on page 13.
3. When a Write cycle is detected, all I/Os are tri-stated, even during Byte Writes.
4. The DQs and DQPX pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
5. CEN = H, inserts wait states.
6. Device powers up deselected with the I/Os in a tri-state condition, regardless of OE.
7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQPX = tri-state when OE is
inactive or when the device is deselected, and DQs and DQPX = data when OE is active.
Document Number: 001-15029 Rev. *E
Page 12 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Truth Table for Read/Write
The read/write truth table for CY7C1471BV33 follows.[8, 9, 10]
Function
WE
BWA
BWB
BWC
BWD
Read
H
X
X
X
X
Write – No bytes written
L
H
H
H
H
Write byte A – (DQA and DQPA)
L
L
H
H
H
Write byte B – (DQB and DQPB)
L
H
L
H
H
Write byte C – (DQC and DQPC)
L
H
H
L
H
Write byte D – (DQD and DQPD)
L
H
H
H
L
Write all bytes
L
L
L
L
L
WE
BWa
BWb
H
X
X
Write – No bytes written
L
H
H
Write byte a – (DQa and DQPa)
L
L
H
Write byte b – (DQb and DQPb)
L
H
L
Write both bytes
L
L
L
Truth Table for Read/Write
The read/write truth table for CY7C1473BV33 follows.[8, 9, 10]
Function
Read
Truth Table for Read/Write
The read/write truth table for CY7C1475BV33 follows.[8, 9, 10]
Function
WE
BWx
Read
H
X
Write – No bytes written
L
H
Write byte X − (DQx and DQPx)
L
L
Write all bytes
L
All BW = L
Notes
8. X = “Don't Care.” H = Logic HIGH, L = Logic LOW. BWX = L signifies at least one Byte Write Select is active, BWX = Valid signifies that the desired Byte Write
Selects are asserted, see section Truth Table for Read/Write on page 13 for details.
9. Write is defined by BWX, and WE. See section Truth Table for Read/Write on page 13.
10. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write is based on which byte write is active.
Document Number: 001-15029 Rev. *E
Page 13 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
IEEE 1149.1 Serial Boundary Scan (JTAG)
The CY7C1471BV33, CY7C1473BV33, and CY7C1475BV33
incorporate a serial boundary scan test access port (TAP). This
port operates in accordance with IEEE Standard 1149.1-1990
but does not have the set of functions required for full 1149.1
compliance. These functions from the IEEE specification are
excluded because their inclusion places an added delay in the
critical speed path of the SRAM. Note that the TAP controller
functions in a manner that does not conflict with the operation of
other devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC-standard 3.3 V or 2.5 V I/O logic levels.
Performing a TAP Reset
A RESET is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
During power-up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
TAP Registers
The CY7C1471BV33, CY7C1473BV33, and CY7C1475BV33
contain a TAP controller, instruction register, boundary scan
register, bypass register, and ID register.
Registers are connected between the TDI and TDO balls and
enable data to be scanned into and out of the SRAM test circuitry.
Only one register is selected at a time through the instruction
register. Data is serially loaded into the TDI ball on the rising
edge of TCK. Data is output on the TDO ball on the falling edge
of TCK.
Disabling the JTAG Feature
nstruction Register
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternately be connected to VDD through a pull-up resistor. TDO
must be left unconnected. During power-up, the device comes
up in a reset state, which does not interfere with the operation of
the device.
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO balls as shown in the TAP Controller Block Diagram on
page 17. During power-up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as described
in the previous section.
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test MODE SELECT (TMS)
The TMS input gives commands to the TAP controller and is
sampled on the rising edge of TCK. This ball may be left
unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI ball serially inputs information into the registers and can
be connected to the input of any of the registers. The register
between TDI and TDO is chosen by the instruction that is loaded
into the TAP instruction register. For information about loading
the instruction register, see the TAP Controller State Diagram on
page 16. TDI is internally pulled up and can be unconnected if
the TAP is unused in an application. TDI is connected to the most
significant bit (MSB) of any register. (See the TAP Controller
Block Diagram on page 17.)
Test Data-Out (TDO)
The TDO output ball serially clocks data-out from the registers.
The output is active depending upon the current state of the TAP
state machine. The output changes on the falling edge of TCK.
TDO is connected to the least significant bit (LSB) of any register.
(See TAP Controller State Diagram on page 16.)
Document Number: 001-15029 Rev. *E
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary ‘01’ pattern to enable fault
isolation of the board-level serial test data path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This allows the shifting of data through the
SRAM with minimal delay. The bypass register is set LOW (VSS)
when the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The boundary scan register is loaded with the contents of the
RAM I/O ring when the TAP controller is in the Capture-DR state
and is then placed between the TDI and TDO balls when the
controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used to
capture the contents of the I/O ring.
The Boundary Scan Order tables show the order in which the bits
are connected. Each bit corresponds to one of the bumps on the
SRAM package. The MSB of the register is connected to TDI and
the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in the section Identification Register
Definitions on page 20.
Page 14 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in “Identification
Codes” on page 20. Three of these instructions are listed as
RESERVED and must not be used. The other five instructions
are described in detail in this section.
The TAP controller used in this SRAM is not fully compliant to the
1149.1 convention because some of the mandatory 1149.1
instructions are not fully implemented.
The TAP controller cannot be used to load address data or
control signals into the SRAM and cannot preload the I/O buffers.
The SRAM does not implement the 1149.1 commands EXTEST
or INTEST or the PRELOAD portion of SAMPLE/PRELOAD;
rather, it performs a capture of the I/O ring when these
instructions are executed.
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO balls. To execute
the instruction after it is shifted in, the TAP controller must be
moved into the Update-IR state.
EXTEST
EXTEST is a mandatory 1149.1 instruction which must be
executed whenever the instruction register is loaded with all 0s.
EXTEST is not implemented in this SRAM TAP controller, and
therefore this device is not compliant to 1149.1. The TAP
controller does recognize an all-0 instruction.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. The
PRELOAD portion of this instruction is not implemented, so the
device TAP controller is not fully 1149.1 compliant.
When the SAMPLE/PRELOAD instruction is loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and bidirectional balls is
captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because there
is a large difference in the clock frequencies, it is possible that
during the Capture-DR state, an input or output may undergo a
transition. The TAP may then try to capture a signal when in
transition (metastable state). This does not harm the device, but
there is no guarantee as to the value that is captured.
Repeatable results may not be possible.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture setup plus hold
time (tCS plus tCH).
The SRAM clock input might not be captured correctly if there is
no way in a design to stop (or slow) the clock during a
SAMPLE/PRELOAD instruction. If this is an issue, it is still
possible to capture all other signals and simply ignore the value
of the CLK captured in the boundary scan register.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO balls.
When an EXTEST instruction is loaded into the instruction
register, the SRAM responds as if a SAMPLE/PRELOAD
instruction has been loaded. There is one difference between the
two instructions. Unlike the SAMPLE/PRELOAD instruction,
EXTEST places the SRAM outputs in a High-Z state.
Note that because the PRELOAD part of the command is not
implemented, putting the TAP to the Update-DR state when
performing a SAMPLE/PRELOAD instruction has the same
effect as the Pause-DR command.
IDCODE
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO balls. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and enables
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
The IDCODE instruction is loaded into the instruction register
during power-up or whenever the TAP controller is in a test logic
reset state.
BYPASS
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register to
be connected between the TDI and TDO balls when the TAP
controller is in a Shift-DR state. It also places all SRAM outputs
into a High-Z state.
Document Number: 001-15029 Rev. *E
Page 15 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
TAP Controller State Diagram
1
TEST-LOGIC
RESET
0
0
RUN-TEST/
IDLE
1
SELECT
DR-SCA N
1
SELECT
IR-SCAN
0
1
0
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
1
1
EXIT1-IR
0
0
PAUSE-IR
1
0
1
EXIT2-DR
0
EXIT2-IR
1
1
UPDATE-DR
Document Number: 001-15029 Rev. *E
1
0
PAUSE-DR
1
0
1
EXIT1-DR
0
1
0
UPDATE-IR
1
0
Page 16 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
TAP Controller Block Diagram
0
Bypass Register
2 1 0
TDI
Selection
Circuitry
Instruction Register
Selection
Circuitry
TDO
31 30 29 . . . 2 1 0
Identification Register
x . . . . . 2 1 0
Boundary Scan Register
TCK
TM S
Document Number: 001-15029 Rev. *E
TAP CONTROLLER
Page 17 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
3.3-V TAP AC Test Conditions
2.5-V TAP AC Test Conditions
Input pulse levels................................................VSS to 3.3 V
Input pulse levels............................................... VSS to 2.5 V
Input rise and fall times....................................................1 ns
Input rise and fall time .....................................................1 ns
Input timing reference levels.......................................... 1.5 V
Input timing reference levels........................................ 1.25 V
Output reference levels ................................................. 1.5 V
Output reference levels ............................................... 1.25 V
Test load termination supply voltage ............................. 1.5 V
Test load termination supply voltage ........................... 1.25 V
3.3-V TAP AC Output Load Equivalent
2.5-V TAP AC Output Load Equivalent
1.25V
1.5V
50Ω
50Ω
TDO
TDO
Z O= 50Ω
Z O= 50Ω
20pF
20pF
TAP DC Electrical Characteristics and Operating Conditions
(0 °C < TA < +70 °C; VDD = 3.3 V ±0.165 V unless otherwise noted)[11]
Parameter
Description
VOH1
Output HIGH voltage
VOH2
Output HIGH voltage
VOL1
Output LOW voltage
VOL2
Output LOW voltage
VIH
Input HIGH voltage
VIL
Input LOW voltage
IX
Input load current
Min
Max
Unit
IOH = –4.0 mA, VDDQ = 3.3 V
Test Conditions
2.4
–
V
IOH = –1.0 mA, VDDQ = 2.5 V
2.0
–
V
IOH = –100 µA
VDDQ = 3.3 V
2.9
–
V
VDDQ = 2.5 V
2.1
–
V
IOL = 8.0 mA
VDDQ = 3.3 V
–
0.4
V
IOL = 1.0 mA
VDDQ = 2.5 V
–
0.4
V
IOL = 100 µA
VDDQ = 3.3 V
–
0.2
V
GND < VIN < VDDQ
VDDQ = 2.5 V
–
0.2
V
VDDQ = 3.3 V
2.0
VDD + 0.3
V
VDDQ = 2.5 V
1.7
VDD + 0.3
V
VDDQ = 3.3 V
–0.3
0.8
V
VDDQ = 2.5 V
–0.3
0.7
V
–5
5
µA
Notes
11. All voltages refer to VSS (GND).
Document Number: 001-15029 Rev. *E
Page 18 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
TAP AC Switching Characteristics
Over the Operating Range[12, 13]
Parameter
Description
Min
Max
Unit
50
–
ns
Clock
tTCYC
TCK clock cycle time
tTF
TCK clock frequency
–
20
MHz
tTH
TCK clock HIGH time
20
–
ns
tTL
TCK clock LOW time
20
–
ns
Output Times
tTDOV
TCK clock LOW to TDO valid
–
5
ns
tTDOX
TCK clock LOW to TDO invalid
0
–
ns
tTMSS
TMS setup to TCK clock rise
5
–
ns
tTDIS
TDI setup to TCK clock rise
5
–
ns
tCS
Capture setup to TCK rise
5
–
ns
tTMSH
TMs hold after TCK clock rise
5
–
ns
tTDIH
TDI hold after clock rise
5
–
ns
tCH
Capture hold after clock rise
5
–
ns
Setup Times
Hold Times
TAP Timing
Figure 3. TAP Timing
1
2
Test Clock
(TCK )
3
t TH
t TM SS
t TM SH
t TDIS
t TDIH
t
TL
4
5
6
t CY C
Test M ode Select
(TM S)
Test Data-In
(TDI)
t TDOV
t TDOX
Test Data-Out
(TDO)
DON’T CA RE
UNDEFINED
Notes
12. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
13. Test conditions are specified using the load in TAP AC Test Conditions. tR/tF = 1 ns.
Document Number: 001-15029 Rev. *E
Page 19 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Identification Register Definitions
Instruction Field
CY7C1471BV33 CY7C1473BV33 CY7C1475BV33
(2 M × 36)
(4 M × 18)
(1 M × 72)
Revision number (31:29)
[14]
000
000
000
Description
Describes the version number
01011
01011
01011
Architecture/memory type(23:18)
001001
001001
001001
Defines memory type and architecture
Bus width/density(17:12)
100100
010100
110100
Defines width and density
00000110100
00000110100
00000110100
1
1
1
Device depth (28:24)
Cypress JEDEC ID code (11:1)
ID register presence indicator (0)
Reserved for internal use
Enables unique identification of SRAM
vendor
Indicates the presence of an ID
register
Scan Register Sizes
Register Name
Instruction
Bit Size (x36)
Bit Size (x18)
Bit Size (x72)
3
3
3
Bypass
1
1
1
ID
32
32
32
Boundary scan order – 165FBGA
71
52
–
Boundary scan order – 209BGA
–
–
110
Identification Codes
Instruction
Code
Description
EXTEST
000
Captures I/O ring contents. Places the boundary scan register between TDI
and TDO. Forces all SRAM outputs to High-Z state. This instruction is not
1149.1-compliant.
IDCODE
001
Loads the ID register with the vendor ID code and places the register
between TDI and TDO. This operation does not affect SRAM operations.
SAMPLE Z
010
Captures I/O ring contents. Places the boundary scan register between TDI
and TDO. Forces all SRAM output drivers to a High-Z state.
RESERVED
011
Do not use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures I/O ring contents. Places the boundary scan register between TDI
and TDO. Does not affect SRAM operation. This instruction does not
implement 1149.1 preload function and is therefore not 1149.1 compliant.
RESERVED
101
Do not use: This instruction is reserved for future use.
RESERVED
110
Do not use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not
affect SRAM operations.
Note
14. Bit #24 is “1” in the ID Register Definitions for both 2.5 V and 3.3 V versions of this device.
Document Number: 001-15029 Rev. *E
Page 20 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Boundary Scan Exit Order (2 M × 36)
Bit #
165-Ball ID
Bit #
165-Ball ID
Bit #
165-Ball ID
Bit #
165-Ball ID
1
C1
21
R3
2
D1
22
P2
41
J11
61
B7
42
K10
62
B6
3
E1
23
R4
43
J10
63
A6
4
D2
24
P6
44
H11
64
B5
5
E2
25
R6
45
G11
65
A5
6
F1
26
R8
46
F11
66
A4
7
G1
27
P3
47
E11
67
B4
8
F2
28
P4
48
D10
68
B3
9
G2
29
P8
49
D11
69
A3
10
J1
30
P9
50
C11
70
A2
11
K1
31
P10
51
G10
71
B2
12
L1
32
R9
52
F10
13
J2
33
R10
53
E10
14
M1
34
R11
54
A9
15
N1
35
N11
55
B9
16
K2
36
M11
56
A10
17
L2
37
L11
57
B10
18
M2
38
M10
58
A8
19
R1
39
L10
59
B8
20
R2
40
K11
60
A7
Boundary Scan Exit Order (4 M × 18)
Bit #
165-Ball ID
Bit #
165-Ball ID
Bit #
165-Ball ID
Bit #
165-Ball ID
1
D2
14
R4
27
L10
40
B10
2
E2
15
P6
28
K10
41
A8
3
F2
16
R6
29
J10
42
B8
4
G2
17
R8
30
H11
43
A7
5
J1
18
P3
31
G11
44
B7
6
K1
19
P4
32
F11
45
B6
7
L1
20
P8
33
E11
46
A6
8
M1
21
P9
34
D11
47
B5
9
N1
22
P10
35
C11
48
A4
10
R1
23
R9
36
A11
49
B3
11
R2
24
R10
37
A9
50
A3
12
R3
25
R11
38
B9
51
A2
13
P2
26
M10
39
A10
52
B2
Document Number: 001-15029 Rev. *E
Page 21 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Boundary Scan Exit Order (1 M × 72)
Bit #
209-Ball ID
Bit #
209-Ball ID
Bit #
209-Ball ID
Bit #
209-Ball ID
1
A1
29
T1
57
U10
85
B11
2
A2
30
T2
58
T11
86
B10
3
B1
31
U1
59
T10
87
A11
4
B2
32
U2
60
R11
88
A10
5
C1
33
V1
61
R10
89
A7
6
C2
34
V2
62
P11
90
A5
7
D1
35
W1
63
P10
91
A9
8
D2
36
W2
64
N11
92
U8
9
E1
37
T6
65
N10
93
A6
10
E2
38
V3
66
M11
94
D6
11
F1
39
V4
67
M10
95
K6
12
F2
40
U4
68
L11
96
B6
13
G1
41
W5
69
L10
97
K3
14
G2
42
V6
70
P6
98
A8
15
H1
43
W6
71
J11
99
B4
16
H2
44
V5
72
J10
100
B3
17
J1
45
U5
73
H11
101
C3
18
J2
46
U6
74
H10
102
C4
19
L1
47
W7
75
G11
103
C8
20
L2
48
V7
76
G10
104
C9
21
M1
49
U7
77
F11
105
B9
22
M2
50
V8
78
F10
106
B8
23
N1
51
V9
79
E10
107
A4
24
N2
52
W11
80
E11
108
C6
25
P1
53
W10
81
D11
109
B7
26
P2
54
V11
82
D10
110
A3
27
R2
55
V10
83
C11
28
R1
56
U11
84
C10
Document Number: 001-15029 Rev. *E
Page 22 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Maximum Ratings
Current into outputs (LOW) ......................................... 20 mA
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage temperature ................................ –65 °C to +150 °C
Static discharge voltage........................................... >2001 V
(MIL-STD-883, Method 3015)
Latch-up current ..................................................... >200 mA
Ambient temperature with power applied . –55 °C to +125 °C
Supply voltage on VDD relative to GND ........–0.5 V to +4.6 V
Operating Range
Supply voltage on VDDQ relative to GND....... –0.5 V to +VDD
Ambient
VDD
VDDQ
Temperature
Commercial 0 °C to +70 °C 3.3 V –5%/+10% 2.5 V – 5%
to VDD
Industrial
–40 °C to +85 °C
DC voltage applied to
outputs in tri-state ..............................–0.5 V to VDDQ + 0.5 V
DC input voltage .................................. –0.5 V to VDD + 0.5 V
Range
Electrical Characteristics
Over the Operating Range[15, 16]
Parameter
Description
VDD
Power supply voltage
VDDQ
I/O supply voltage
Test Conditions
Min
Max
Unit
3.135
3.6
V
V
For 3.3 V I/O
3.135
VDD
For 2.5 V I/O
2.375
2.625
V
For 3.3 V I/O, IOH = –4.0 mA
2.4
–
V
For 2.5 V I/O, IOH = –1.0 mA
2.0
–
V
–
0.4
V
VOH
Output HIGH voltage
VOL
Output LOW voltage
VIH
Input HIGH voltage[15]
For 3.3 V I/O
VIL
Input LOW voltage[15]
For 2.5 V I/O
IX
Input leakage current except GND ≤ VI ≤ VDDQ
ZZ and MODE
Input current of MODE
Input = VSS
Input = VDD
–
5
μA
Input current of ZZ
Input = VSS
–5
–
μA
Output leakage current
GND ≤ VI ≤ VDD, output disabled
For 3.3 V I/O, IOL = 8.0 mA
For 2.5 V I/O, IOL = 1.0 mA
–
0.4
V
2.0
VDD + 0.3 V
V
For 2.5 V I/O
1.7
VDD + 0.3 V
V
For 3.3 V I/O
–0.3
0.8
V
–0.3
0.7
V
–5
5
μA
–30
–
μA
30
μA
–5
5
μA
–
305
mA
Input = VDD
IOZ
IDD
[17]
VDD operating supply current VDD = Max., IOUT = 0 mA,
f = fMAX = 1/tCYC
7.5 ns cycle, 133 MHz
–
10 ns cycle, 117 MHz
–
275
mA
7.5 ns cycle, 133 MHz
–
200
mA
–
200
mA
–
120
mA
200
mA
200
mA
Automatic CE
power-down
current—TTL inputs
VDD = Max, device deselected,
VIN ≥ VIH or VIN ≤ VIL
f = fMAX, inputs switching
ISB2
Automatic CE
power-down
current—CMOS inputs
VDD = Max, device deselected,
All speeds
VIN ≤ 0.3 V or VIN > VDD – 0.3 V,
f = 0, inputs static
ISB3
Automatic CE
power-down
current—CMOS inputs
VDD = Max, device deselected, or 7.5 ns cycle, 133 MHz
VIN ≤ 0.3 V or VIN > VDDQ – 0.3 V
f = fMAX, inputs switching
10 ns cycle, 117 MHz
–
ISB1
–
10 ns cycle, 117 MHz
–
–
Notes
15. Overshoot: VIH(AC) < VDD +1.5 V (pulse width less than tCYC/2). Undershoot: VIL(AC) > –2 V (pulse width less than tCYC/2).
16. TPower-up: assumes a linear ramp from 0 V to VDD(min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
17. The operation current is calculated with 50% read cycle and 50% write cycle.
Document Number: 001-15029 Rev. *E
Page 23 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Electrical Characteristics
Over the Operating Range[15, 16] (continued)
Parameter
ISB4
Description
Test Conditions
VDD = Max, device deselected,
All Speeds
VIN ≥ VDD – 0.3 V or VIN ≤ 0.3 V,
f = 0, inputs static
Automatic CE
power-down
current—TTL inputs
Min
Max
Unit
–
165
mA
Capacitance
Tested initially and after any design or process change that may affect these parameters.
Parameter
Description
100-pin TQFP 165-ball FBGA 209-ball BGA
Package
Package
Package
Test Conditions
CADDRESS
Address input capacitance
CDATA
Data input capacitance
CCTRL
Control input capacitance
CCLK
CI/O
TA = 25 °C, f = 1 MHz,
VDD = 3.3 V
VDDQ = 2.5 V
Unit
6
6
6
pF
5
5
5
pF
8
8
8
pF
Clock input capacitance
6
6
6
pF
I/O capacitance
5
5
5
pF
Thermal Resistance
Tested initially and after any design or process change that may affect these parameters.
Parameter
Test Conditions
100-pin
TQFP Max
165-ball
FBGA Max
209-ball
FBGA Max
Unit
Test conditions follow standard
test methods and procedures for
measuring thermal impedance,
according to EIA/JESD51.
24.63
16.3
15.2
°C/W
2.28
2.1
1.7
°C/W
Description
θJA
Thermal resistance
(junction to ambient)
θJC
Thermal resistance
(junction to case)
Figure 4. AC Test Loads and Waveforms
3.3 V I/O Test Load
R = 317 Ω
3.3 V
OUTPUT
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50 Ω
Z0 = 50 Ω
10%
90%
10%
90%
GND
5 pF
R = 351 Ω
≤ 1 ns
≤ 1 ns
VL = 1.5 V
INCLUDING
JIG AND
SCOPE
(a)
(c)
(b)
2.5 V I/O Test Load
R = 1667 Ω
2.5 V
OUTPUT
Z0 = 50 Ω
10%
R = 1538 Ω
VL = 1.25 V
Document Number: 001-15029 Rev. *E
INCLUDING
JIG AND
SCOPE
90%
10%
90%
GND
5 pF
(a)
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50 Ω
(b)
≤ 1 ns
≤ 1 ns
(c)
Page 24 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Switching Characteristics
Over the Operating Range. Unless otherwise noted in the following table, timing reference level is 1.5 V when VDDQ = 3.3 V and is
1.25 V when VDDQ = 2.5 V. Test conditions shown in (a) of AC Test Loads and Waveforms on page 24 unless otherwise noted.
Parameter
Description
tPOWER [18]
133 MHz
117 MHz
Unit
Min
Max
Min
Max
1
–
1
–
ms
Clock
tCYC
Clock cycle time
7.5
–
10
–
ns
tCH
Clock HIGH
2.5
–
3.0
–
ns
tCL
Clock LOW
2.5
–
3.0
–
ns
Output Times
tCDV
Data output valid after CLK rise
–
6.5
–
8.5
ns
tDOH
Data output hold after CLK rise
2.5
–
2.5
–
ns
tCLZ
Clock to low-Z [19, 20, 21]
3.0
–
3.0
–
ns
–
3.8
–
4.5
ns
–
3.0
–
3.8
ns
[19, 20, 21]
tCHZ
Clock to high-Z
tOEV
OE LOW to output valid
[19, 20, 21]
tOELZ
OE LOW to output low-Z
tOEHZ
OE HIGH to output high-Z [19, 20, 21]
0
–
0
–
ns
–
3.0
–
4.0
ns
Setup Times
tAS
Address setup before CLK rise
1.5
–
1.5
–
ns
tALS
ADV/LD setup before CLK rise
1.5
–
1.5
–
ns
tWES
WE, BWX setup before CLK rise
1.5
–
1.5
–
ns
tCENS
CEN setup before CLK rise
1.5
–
1.5
–
ns
tDS
Data input setup before CLK rise
1.5
–
1.5
–
ns
tCES
Chip enable setup before CLK rise
1.5
–
1.5
–
ns
tAH
Address hold after CLK rise
0.5
–
0.5
–
ns
tALH
ADV/LD hold after CLK rise
0.5
–
0.5
–
ns
tWEH
WE, BWX hold after CLK rise
0.5
–
0.5
–
ns
tCENH
CEN hold after CLK rise
0.5
–
0.5
–
ns
tDH
Data input hold after CLK rise
0.5
–
0.5
–
ns
tCEH
Chip enable hold after CLK rise
0.5
–
0.5
–
ns
Hold Times
Notes
18. This part has an internal voltage regulator; tPOWER is the time that the power must be supplied above VDD(minimum) initially, before a read or write operation is initiated.
19. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads and Waveforms on page 24. Transition is measured ±200 mV
from steady-state voltage.
20. At any supplied voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to
achieve High-Z before Low-Z under the same system conditions.
21. This parameter is sampled and not 100% tested.
Document Number: 001-15029 Rev. *E
Page 25 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Switching Waveforms
Figure 5 shows read-write timing waveform.[22, 23, 24]
Figure 5. Read/Write Timing
1
2
3
t CYC
4
5
6
7
8
9
A5
A6
A7
10
CLK
t CENS
t CENH
t CES
t CEH
t CH
t CL
CEN
CE
ADV/LD
WE
BW X
A1
ADDRESS
t AS
A2
A4
A3
t CDV
t AH
t DOH
t CLZ
DQ
D(A1)
t DS
D(A2)
Q(A3)
D(A2+1)
t OEV
Q(A4+1)
Q(A4)
t OELZ
W RITE
D(A1)
W RITE
D(A2)
D(A5)
Q(A6)
D(A7)
W RITE
D(A7)
DESELECT
t OEHZ
t DH
OE
COM M AND
t CHZ
BURST
W RITE
D(A2+1)
READ
Q(A3)
READ
Q(A4)
DON’T CARE
BURST
READ
Q(A4+1)
t DOH
W RITE
D(A5)
READ
Q(A6)
UNDEFINED
Notes
22. For this waveform ZZ is tied LOW.
23. When CE is LOW, CE1 is LOW, CE2 is HIGH, and CE3 is LOW. When CE is HIGH, CE1 is HIGH, CE2 is LOW or CE3 is HIGH.
24. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document Number: 001-15029 Rev. *E
Page 26 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Switching Waveforms (continued)
[25, 26, 27]
Figure 6 shows NOP, STALL and DESELECT Cycles waveform.
Figure 6. NOP, STALL, and DESELECT Cycles
1
2
A1
A2
3
4
5
A3
A4
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BW [A:D]
ADDRESS
A5
t CHZ
D(A1)
DQ
Q(A2)
Q(A3)
D(A4)
Q(A5)
t DOH
COMMAND
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
DON’T CARE
STALL
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
UNDEFINED
Notes
25. For this waveform ZZ is tied LOW.
26. When CE is LOW, CE1 is LOW, CE2 is HIGH, and CE3 is LOW. When CE is HIGH, CE1 is HIGH, CE2 is LOW or CE3 is HIGH.
27. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrates CEN being used to create a pause. A write is not performed during this cycle.
Document Number: 001-15029 Rev. *E
Page 27 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Switching Waveforms (continued)
Figure 7 shows ZZ Mode timing waveform.
[28, 29]
Figure 7. ZZ Mode Timing
CLK
t ZZ
ZZ
I
t ZZREC
t ZZI
SUPPLY
I DDZZ
t RZZI
ALL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes
28. Device must be deselected when entering ZZ mode. See the Truth Table on page 12 for all possible signal conditions to deselect the device.
29. DQs are in high-Z when exiting ZZ sleep mode.
Document Number: 001-15029 Rev. *E
Page 28 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Ordering Information
Table 1 lists the CY7C1471BV33, CY7C1473BV33, CY7C1475BV33 key package features and ordering codes. The table contains
only the parts that are currently available. If you do not see what you are looking for, contact your local sales representative. For more
information, visit the Cypress website at www.cypress.com and refer to the product summary page at
http://www.cypress.com/products.
Table 1. CY7C1471BV33, CY7C1473BV33, CY7C1475BV33 Key Features and Ordering Information
Package
100-pin TQFP (14 × 20 × 1.4 mm) Pb-free
Ordering Code
CY7C1471BV33-133AXC
Speed
(MHz)
Package
Diagram
Operating
Ranges
133
51-85050
Commercial
CY7C1473BV33-133AXC
Ordering Code Definitions
CY 7C 14XX
B
V33 - XXX AX C
Temperature Range:
C = Commercial
Package Type:
AX = 100-pin TQFP (Pb-free)
Speed Grade: XXX = 133 MHz
V33 = 3.3 V
Die Revision
Part Identifier: 14XX = 1471 (2 M × 36) or 1473 (4 M × 18)
Marketing Code: 7C = SRAM
Company ID: CY = Cypress
Document Number: 001-15029 Rev. *E
Page 29 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Package Diagrams
Figure 8. 100-pin TQFP (14 × 20 × 1.4 mm)
51-85050 *D
Document Number: 001-15029 Rev. *E
Page 30 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Package Diagrams
(continued)
Figure 9. 165-ball FBGA (15 × 17 × 1.4 mm)
51-85165 *C
Document Number: 001-15029 Rev. *E
Page 31 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Package Diagrams
(continued)
Figure 10. 209-ball FBGA (14 × 22 × 1.76 mm)
51-85167 *A
Document Number: 001-15029 Rev. *E
Page 32 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Reference Information
Document Conventions
Acronyms
Units of Measure
Table 2. Acronyms
Table 3. Units of Measure
Acronym
Symbol
Description
Unit of Measure
FBGA
fine-pitch ball grid array
°C
I/O
input/output
kW
kilo ohm
JTAG
joint test action group
MHz
megahertz
LSB
least significant bit
µA
microampere
MSB
most significant bit
µs
microsecond
PLL
phase-locked loop
mA
milliampere
SRAM
static random access memory
mm
millimeter
TAP
test access port
ms
millisecond
TCK
test clock
mV
millivolt
TDI
test data-in
ns
nanosecond
TDO
test data-out
W
ohm
TMS
test mode select
%
percent
thin quad flat pack
pF
picofarad
V
volt
W
watt
TQFP
Document Number: 001-15029 Rev. *E
degree Celcius
Page 33 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Document History Page
Document Title: CY7C1471BV33/CY7C1473BV33/CY7C1475BV33, 72-Mbit (2 M × 36/4 M × 18/1 M × 72) Flow-Through SRAM
with NoBL™ Architecture
Document Number: 001-15029
Revision
ECN
Orig. of
Change
Submission
Date
**
1024500
VKN/KKVT
MP
See ECN
New Datasheet
*A
1274731
VKN/AESA
See ECN
Corrected typo in the “NOP, STALL and DESELECT Cycles” waveform
*B
2183566
VKN/PYRS
See ECN
Converted from preliminary to final
Added footnote 16 related to IDD
*C
2898663
NJY
03/24/2010
Removed inactive parts from Ordering Information table; Updated package
diagrams.
*D
2905600
VKN
04/06/2010
Removed inactive part CY7C1471BV33-117AXC from the ordering information
table.
*E
3298193
OSN
06/30/2011
Updated template and styles to meet current CY standards.
Added table of contents.
Added Acronyms, Units and Ordering Information table.
Updated package diagrams:
51-85050 – *C to *D revision
51-85165 – *B to *C revision
Document Number: 001-15029 Rev. *E
Description of Change
Page 34 of 35
[+] Feedback
CY7C1471BV33, CY7C1473BV33, CY7C1475BV33
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
PSoC
Touch Sensing
cypress.com/go/memory
cypress.com/go/image
cypress.com/go/psoc
cypress.com/go/touch
USB Controllers
Wireless/RF
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2007-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-15029 Rev. *E
Revised June 30, 2011
Page 35 of 35
All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback