CYPRESS CY7C1354C

CY7C1354C, CY7C1356C
9-Mbit (256 K × 36/512 K × 18)
Pipelined SRAM with NoBL™ Architecture
9-Mbit (256 K × 36/512 K × 18) Pipelined SRAM with NoBL™ Architecture
Features
Functional Description
■
Pin-compatible and functionally equivalent to ZBT
■
Supports 250 MHz bus operations with zero wait states
❐ Available speed grades are 250, 200, and 166 MHz
■
Internally self-timed output buffer control to eliminate the
need to use asynchronous OE
■
Fully registered (inputs and outputs) for pipelined
operation
■
Byte write capability
■
Single 3.3 V power supply (VDD)
■
3.3 V or 2.5 V I/O power supply (VDDQ)
■
Fast clock-to-output times
❐ 2.8 ns (for 250 MHz device)
■
Clock enable (CEN) pin to suspend operation
■
Synchronous self-timed writes
■
Available in Pb-free 100-pin TQFP package, Pb-free, and
non Pb-free 119-ball BGA package and 165-ball FBGA
package
The CY7C1354C and CY7C1356C[1] are 3.3 V, 256 K x 36 and
512K x 18 synchronous pipelined burst SRAMs with No Bus
Latency™ (NoBL logic, respectively. They are designed to
support unlimited true back-to-back read/write operations with
no wait states. The CY7C1354C and CY7C1356C are
equipped with the advanced (NoBL) logic required to enable
consecutive read/write operations with data being transferred
on every clock cycle. This feature greatly improves the
throughput of data in systems that require frequent write/read
transitions. The CY7C1354C and CY7C1356C are pin
compatible and functionally equivalent to ZBT devices.
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock. The
clock input is qualified by the clock enable (CEN) signal, which
when deasserted suspends operation and extends the
previous clock cycle.
■
IEEE 1149.1 JTAG-compatible boundary scan
■
Burst capability – linear or interleaved burst order
■
“ZZ” sleep mode option and stop clock option
Write operations are controlled by the byte write selects
(BWa–BWd for CY7C1354C and BWa–BWb for CY7C1356C)
and a write enable (WE) input. All writes are conducted with
on-chip synchronous self-timed write circuitry.
Three synchronous chip enables (CE1, CE2, CE3) and an
asynchronous output enable (OE) provide for easy bank
selection and output tristate control. To avoid bus contention,
the output drivers are synchronously tristated during the data
portion of a write sequence.
Logic Block Diagram – CY7C1354C (256 K × 36)
ADDRESS
REGISTER 0
A0, A1, A
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
S
E
N
S
E
ADV/LD
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
BW a
BW b
BW c
BW d
WRITE
DRIVERS
MEMORY
ARRAY
A
M
P
S
WE
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
E
INPUT
REGISTER 1
OE
CE1
CE2
CE3
E
O
U
T
P
U
T
D
A
T
A
S
T
E
E
R
I
N
G
INPUT
REGISTER 0
B
U
F
F
E
R
S
DQ s
DQ Pa
DQ Pb
DQ Pc
DQ Pd
E
E
READ LOGIC
SLEEP
CONTROL
ZZ
Note
1. For best-practices recommendations, refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document Number: 38-05538 Rev. *K
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 2, 2011
[+] Feedback
CY7C1354C, CY7C1356C
Logic Block Diagram – CY7C1356C (512 K × 18)
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
S
E
N
S
E
ADV/LD
BW a
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
A
M
P
S
BW b
WE
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
O
U
T
P
U
T
D
A
T
A
B
U
F
F
E
R
S
S
T
E
E
R
I
N
G
E
INPUT
REGISTER 1
OE
CE1
CE2
CE3
ZZ
Document Number: 38-05538 Rev. *K
E
DQ s
DQ Pa
DQ Pb
E
INPUT
REGISTER 0
E
READ LOGIC
Sleep
Control
Page 2 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Contents
Selection Guide ................................................................ 4
Pin Configurations ........................................................... 4
Pin Definitions .................................................................. 7
Functional Overview ........................................................ 8
Single Read Accesses ................................................ 8
Burst Read Accesses .................................................. 8
Single Write Accesses ................................................. 8
Burst Write Accesses .................................................. 9
Sleep Mode ................................................................. 9
Partial Write Cycle Description ..................................... 10
Truth Table ...................................................................... 10
Partial Write Cycle Description ..................................... 11
IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 12
Disabling the JTAG Feature ...................................... 12
TAP Controller State Diagram ....................................... 12
Test Access Port (TAP) ............................................. 12
TAP Controller Block Diagram ...................................... 12
PERFORMING A TAP RESET .................................. 12
TAP REGISTERS ...................................................... 13
TAP Instruction Set ................................................... 13
TAP Timing ...................................................................... 14
TAP AC Switching Characteristics ............................... 14
3.3 V TAP AC Test Conditions ....................................... 15
3.3 V TAP AC Output Load Equivalent ......................... 15
2.5 V TAP AC Test Conditions ....................................... 15
2.5 V TAP AC Output Load Equivalent ......................... 15
Document Number: 38-05538 Rev. *K
TAP DC Electrical Characteristics
and Operating Conditions ............................................. 15
Identification Register Definitions ................................ 15
Scan Register Sizes ....................................................... 16
Identification Codes ....................................................... 16
Boundary Scan Exit Order (256 K × 36) ........................ 17
Boundary Scan Exit Order (512 K × 18) ........................ 18
Maximum Ratings ........................................................... 19
Operating Range ............................................................. 19
Neutron Soft Error Immunity ......................................... 19
Electrical Characteristics ............................................... 19
Capacitance .................................................................... 20
Thermal Resistance ........................................................ 20
Switching Characteristics .............................................. 22
Switching Waveforms .................................................... 23
Ordering Information ...................................................... 26
Ordering Code Definitions ......................................... 26
Package Diagrams .......................................................... 27
Acronyms ........................................................................ 30
Document Conventions ................................................. 30
Units of Measure ....................................................... 30
Document History Page ................................................. 31
Sales, Solutions, and Legal Information ...................... 32
Worldwide Sales and Design Support ....................... 32
Products .................................................................... 32
PSoC Solutions ......................................................... 32
Page 3 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Selection Guide
Description
Maximum access time
Maximum operating current
Maximum CMOS standby current
250 MHz
2.8
250
40
200 MHz
3.2
220
40
166 MHz
3.5
180
40
Unit
ns
mA
mA
Pin Configurations
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CY7C1356C
(512 K × 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A
NC
NC
VDDQ
VSS
NC
DQPa
DQa
DQa
VSS
VDDQ
DQa
DQa
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
NC
NC
VSS
VDDQ
NC
NC
NC
A
A
A
A
A
A
A
NC(36)
NC(72)
VSS
VDD
NC(288)
NC(144)
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NC
DQPb
NC
DQb
NC
DQb
VDDQ VDDQ
VSS
VSS
NC
DQb
DQb
NC
DQb
DQb
DQb
DQb
VSS
VSS
VDDQ VDDQ
DQb
DQb
DQb
DQb
NC
VSS
VDD
NC
VDD
NC
VSS
ZZ
DQb
DQa
DQa
DQb
VDDQ VDDQ
VSS
VSS
DQa
DQb
DQa
DQb
DQa DQPb
NC
DQa
VSS
VSS
VDDQ VDDQ
NC
DQa
DQa
NC
DQPa
NC
MODE
A
A
A
A
A1
A0
Document Number: 38-05538 Rev. *K
A
A
A
A
A
A
A
NC(36)
NC(72)
VSS
DQd
DQd
VDDQ
VSS
DQd
DQd
DQd
DQd
VSS
VDDQ
DQd
DQd
DQPd
CY7C1354C
(256 K × 36)
VSS
VDD
NC
NC(288)
NC(144)
DQc
DQc
NC
VDD
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VSS
DQc
DQc
DQc
DQc
VSS
VDDQ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
DQPc
DQc
DQc
VDDQ
A
A
A
A
CE1
CE2
NC
NC
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
NC(18)
A
A
A
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE1
CE2
BWd
BWc
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
NC(18)
A
Figure 1. 100-pin TQFP
Page 4 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Figure 2. 119-ball BGA Pinout
CY7C1354C (256 K × 36)
1
2
3
4
5
6
7
A
VDDQ
A
A
NC/18M
A
A
VDDQ
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
NC/1G
DQc
CE2
A
DQPc
A
A
VSS
ADV/LD
VDD
NC
A
A
VSS
CE3
A
DQPb
NC
NC
DQb
CE1
VSS
DQb
DQb
OE
A
VSS
DQb
VDDQ
BWb
DQb
DQb
WE
VDD
VSS
NC
DQb
VDD
DQb
VDDQ
CLK
NC
VSS
BWa
DQa
DQa
DQa
DQa
R
T
U
DQc
DQc
VSS
VDDQ
DQc
VSS
DQc
DQc
DQc
VDDQ
DQc
VDD
BWc
VSS
NC
DQd
DQd
DQd
DQd
BWd
VDDQ
DQd
VSS
DQa
VDDQ
DQd
VSS
CEN
A1
VSS
DQd
VSS
DQa
DQa
DQd
DQPd
VSS
A0
VSS
DQPa
DQa
NC/144M
A
MODE
VDD
NC/288M
NC/72M
A
A
NC
A
A
NC
NC/36M
ZZ
VDDQ
TMS
TDI
TCK
TDO
NC
VDDQ
VSS
CY7C1356C (512 K x 18)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
1
2
3
4
5
6
7
VDDQ
A
A
NC/18M
A
A
VDDQ
NC/576M
CE2
A
A
A
ADV/LD
VDD
A
NC/1G
A
CE3
A
NC
NC
DQb
NC
VSS
NC
VSS
DQPa
NC
NC
DQb
VSS
CE1
VSS
NC
DQa
VDDQ
NC
VSS
VSS
DQa
VDDQ
NC
DQb
VDDQ
DQb
NC
VDD
BWb
VSS
NC
OE
A
WE
VDD
VSS
VSS
NC
NC
DQa
VDD
DQa
NC
VDDQ
NC
DQb
VSS
CLK
VSS
NC
DQa
DQb
NC
VSS
NC
NC
DQb
VSS
NC
VDDQ
DQb
NC
VSS
CEN
A1
BWa
VSS
DQa
VDDQ
VSS
DQa
NC
NC
DQPb
VSS
A0
VSS
NC
DQa
NC/144M
A
MODE
VDD
NC
A
NC/288M
NC/72M
A
A
NC/36M
A
A
ZZ
VDDQ
TMS
TDI
TCK
TDO
NC
VDDQ
Document Number: 38-05538 Rev. *K
Page 5 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Figure 3. 165-ball FBGA
CY7C1354C (256 K × 36)
4
5
6
7
1
2
3
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
A
CE1
BWc
BWb
CE3
NC/1G
A
NC
DQc
CE2
VDDQ
BWa
VSS
VDDQ
BWd
VSS
VDD
R
MODE
DQPc
DQc
VSS
8
9
10
11
ADV/LD
A
A
NC
CLK
CEN
WE
OE
NC/18M
A
NC
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
NC
DQb
DQPb
DQb
DQc
DQc
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQb
DQb
DQc
DQc
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQb
DQb
DQc
NC
DQd
DQc
NC
DQd
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
DQb
NC
DQa
DQb
ZZ
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQPd
DQd
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQa
NC
DQa
DQPa
A
A
TDI
A1
TDO
A
A
A
NC/288M
A
A
TMS
A0
TCK
A
A
A
A
NC/144M NC/72M
NC/36M
NC
CY7C1356C (512 K × 18)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1
2
3
4
5
6
7
8
9
10
11
NC/576M
A
CE1
NC
CE3
CEN
ADV/LD
A
A
A
NC/1G
NC
NC
A
NC
DQb
BWb
NC
VDDQ
BWa
CLK
NC
VDDQ
VDDQ
VSS
VSS
VSS
OE
VSS
VDD
A
VSS
WE
VSS
VSS
NC/18M
VSS
VDD
VDDQ
NC
NC
DQPa
DQa
CE2
NC
DQb
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQa
NC
DQb
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQa
NC
NC
DQb
DQb
NC
NC
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
NC
NC
DQa
DQa
ZZ
NC
DQb
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
NC
DQb
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
NC
DQb
DQPb
NC
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQa
NC
NC
NC
NC/144M NC/72M
A
A
TDI
A1
TDO
A
A
A
NC/288M
NC/36M
A
A
TMS
A0
TCK
A
A
A
A
MODE
Document Number: 38-05538 Rev. *K
NC
Page 6 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Pin Definitions
Pin Name
I/O Type
Pin Description
A0, A1, A
Inputsynchronous
Address inputs used to select one of the address locations. Sampled at the rising edge of
the CLK.
BWa,BWb,
BWc,BWd,
Inputsynchronous
Byte write select inputs, active LOW. Qualified with WE to conduct writes to the SRAM.
Sampled on the rising edge of CLK. BWa controls DQa and DQPa, BWb controls DQb and DQPb,
BWc controls DQc and DQPc, BWd controls DQd and DQPd.
WE
Inputsynchronous
Write enable input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This
signal must be asserted LOW to initiate a write sequence.
ADV/LD
Inputsynchronous
Advance/load input used to advance the on-chip address counter or load a new address.
When HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a
new address can be loaded into the device for an access. After being deselected, ADV/LD should
be driven LOW to load a new address.
CLK
Inputclock
Clock input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN.
CLK is only recognized if CEN is active LOW.
CE1
Inputsynchronous
Chip enable 1 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE2 and CE3 to select/deselect the device.
CE2
Inputsynchronous
Chip enable 2 input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE3 to select/deselect the device.
CE3
Inputsynchronous
Chip enable 3 input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE1 and CE2 to select/deselect the device.
OE
InputOutput enable, active LOW. Combined with the synchronous logic block inside the device to
asynchronous control the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs.
When deasserted HIGH, I/O pins are tristated, and act as input data pins. OE is masked during
the data portion of a Write sequence, during the first clock when emerging from a deselected
state and when the device has been deselected.
CEN
Inputsynchronous
Clock enable input, active LOW. When asserted LOW the clock signal is recognized by the
SRAM. When deasserted HIGH the clock signal is masked. Since deasserting CEN does not
deselect the device, CEN can be used to extend the previous cycle when required.
DQS
I/Osynchronous
Bidirectional data I/O lines. As inputs, they feed into an on-chip data register that is triggered
by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by addresses during the previous clock rise of the read cycle. The direction of the pins
is controlled by OE and the internal control logic. When OE is asserted LOW, the pins can behave
as outputs. When HIGH, DQa–DQd are placed in a tristate condition. The outputs are
automatically tristated during the data portion of a write sequence, during the first clock when
emerging from a deselected state, and when the device is deselected, regardless of the state
of OE.
DQPX
I/Osynchronous
Bidirectional data parity I/O lines. Functionally, these signals are identical to DQ[a:d]. During
write sequences, DQPa is controlled by BWa, DQPb is controlled by BWb, DQPc is controlled by
BWc, and DQPd is controlled by BWd.
MODE
TDO
Input strap pin Mode input. Selects the burst order of the device. Tied HIGH selects the interleaved burst order.
Pulled LOW selects the linear burst order. MODE should not change states during operation.
When left floating MODE will default HIGH, to an interleaved burst order.
JTAG serial
output
synchronous
Serial data out to the JTAG circuit. Delivers data on the negative edge of TCK.
TDI
JTAG serial input Serial data in to the JTAG circuit. Sampled on the rising edge of TCK.
synchronous
TMS
Test mode select This pin controls the test access port state machine. Sampled on the rising edge of TCK.
synchronous
TCK
JTAG-clock
VDD
Power supply
Clock input to the JTAG circuitry.
Power supply inputs to the core of the device.
Document Number: 38-05538 Rev. *K
Page 7 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Pin Definitions
Pin Name
VDDQ
(continued)
I/O Type
Pin Description
I/O power supply Power supply for the I/O circuitry.
VSS
Ground
NC
–
No connects. This pin is not connected to the die.
NC (18, 36,
72, 144, 288,
576, 1G)
–
These pins are not connected. They will be used for expansion to the 18M, 36M, 72M, 144M
288M, 576M, and 1G densities.
ZZ
Ground for the device. Should be connected to ground of the system.
InputZZ “sleep” Input. This active HIGH input places the device in a non-time-critical “sleep”
asynchronous condition with data integrity preserved. For normal operation, this pin has to be LOW or left
floating. ZZ pin has an internal pull-down.
Functional Overview
The CY7C1354C and CY7C1356C are synchronous-pipelined
burst NoBL SRAMs designed specifically to eliminate wait states
during write/read transitions. All synchronous inputs pass
through input registers controlled by the rising edge of the clock.
The clock signal is qualified with the clock enable input signal
(CEN). If CEN is HIGH, the clock signal is not recognized and all
internal states are maintained. All synchronous operations are
qualified with CEN. All data outputs pass through output registers
controlled by the rising edge of the clock. Maximum access delay
from the clock rise (tCO) is 2.8 ns (250 MHz device).
Accesses can be initiated by asserting all three chip enables
(CE1, CE2, CE3) active at the rising edge of the clock. If clock
enable (CEN) is active LOW and ADV/LD is asserted LOW, the
address presented to the device will be latched. The access can
either be a read or write operation, depending on the status of
the write enable (WE). BW[d:a] can be used to conduct byte write
operations.
Write operations are qualified by the write enable (WE). All writes
are simplified with on-chip synchronous self-timed write circuitry.
Three synchronous chip enables (CE1, CE2, CE3) and an
asynchronous output enable (OE) simplify depth expansion. All
operations (reads, writes, and deselects) are pipelined. ADV/LD
should be driven LOW once the device has been deselected to
load a new address for the next operation.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are all asserted active, (3) the write enable input signal
WE is deasserted HIGH, and (4) ADV/LD is asserted LOW. The
address presented to the address inputs is latched into the
address register and presented to the memory core and control
logic. The control logic determines that a read access is in
progress and enables the requested data to propagate to the
input of the output register. At the rising edge of the next clock
the requested data is allowed to propagate through the output
register and to the data bus within 2.8 ns (250 MHz device)
provided OE is active LOW. After the first clock of the read
access the output buffers are controlled by OE and the internal
control logic. OE must be driven LOW for the device to drive out
the requested data. During the second clock, a subsequent
Document Number: 38-05538 Rev. *K
operation (read/write/deselect) can be initiated. Deselecting the
device is also pipelined. Therefore, when the SRAM is
deselected at clock rise by one of the chip enable signals, its
output tristates following the next clock rise.
Burst Read Accesses
The CY7C1354C and CY7C1356C have an on-chip burst
counter that enables the user the ability to supply a single
address and conduct up to four reads without reasserting the
address inputs. ADV/LD must be driven LOW to load a new
address into the SRAM, as described in the Single Read
Accesses section. The sequence of the burst counter is determined by the MODE input signal. A LOW input on MODE selects
a linear burst mode, a HIGH selects an interleaved burst
sequence. Both burst counters use A0 and A1 in the burst
sequence, and wrap around when incremented sufficiently. A
HIGH input on ADV/LD increments the internal burst counter
regardless of the state of chip enables inputs or WE. WE is
latched at the beginning of a burst cycle. Therefore, the type of
access (read or write) is maintained throughout the burst
sequence.
Single Write Accesses
Write accesses are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are all asserted active, and (3) the write signal WE is
asserted LOW. The address presented to A0–A16 is loaded into
the address register. The write signals are latched into the
control logic block.
On the subsequent clock rise the data lines are automatically
tristated regardless of the state of the OE input signal. This
enables the external logic to present the data on DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1354C and DQa,b/DQPa,b for
CY7C1356C). In addition, the address for the subsequent
access (read/write/deselect) is latched into the address register
if the appropriate control signals are asserted.
On the next clock rise the data presented to DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1354C and DQa,b/DQPa,b for
CY7C1356C or a subset for byte write operations, see the table
Partial Write Cycle Description on page 10 for details) inputs is
latched into the device and the write is complete.
Page 8 of 32
[+] Feedback
CY7C1354C, CY7C1356C
The data written during the write operation is controlled by BW
(BWa,b,c,d for CY7C1354C and BWa,b for CY7C1356C) signals.
The CY7C1354C/CY7C1356C provides byte write capability that
is described in the Write Cycle Description table. Asserting the
write enable input (WE) with the selected byte write select (BW)
input will selectively write to only the desired bytes. Bytes not
selected during a byte write operation remain unaltered. A
synchronous self-timed write mechanism is provided to simplify
the write operations. Byte write capability is included to greatly
simplify read/modify/write sequences, which can be reduced to
simple byte write operations.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation ‘sleep’ mode. Two clock
cycles are required to enter into or exit from this ‘sleep’ mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected prior to entering the “sleep” mode. CE1, CE2,
and CE3, must remain inactive for the duration of tZZREC after the
ZZ input returns LOW.
Because the CY7C1354C and CY7C1356C are common I/O
devices, data should not be driven into the device while the
outputs are active. The output enable (OE) can be deasserted
HIGH before presenting data to the DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1354C and DQa,b/DQPa,b for
CY7C1356C) inputs. Doing so will tristate the output drivers. As
a safety precaution, DQ and DQP (DQa,b,c,d/DQPa,b,c,d for
CY7C1354C and DQa,b/DQPa,b for CY7C1356C) are
automatically tristated during the data portion of a write cycle,
regardless of the state of OE.
Table 1. Interleaved Burst Address Table
(MODE = Floating or VDD)
Burst Write Accesses
Table 2. Linear Burst Address Table (MODE = GND)
The CY7C1354C/CY7C1356C has an on-chip burst counter that
enables the user the ability to supply a single address and
conduct up to four write operations without reasserting the
address inputs. ADV/LD must be driven LOW to load the initial
address, as described in Single Write Accesses on page 8.
When ADV/LD is driven HIGH on the subsequent clock rise, the
chip enables (CE1, CE2, and CE3) and WE inputs are ignored
and the burst counter is incremented. The correct BW (BWa,b,c,d
for CY7C1354C and BWa,b for CY7C1356C) inputs must be
driven in each cycle of the burst write to write the correct bytes
of data.
First
Address
A1, A0
00
01
10
11
First
Address
A1, A0
00
01
10
11
Second
Address
A1, A0
01
00
11
10
Second
Address
A1, A0
01
10
11
00
Third
Address
A1, A0
10
11
00
01
Third
Address
A1, A0
10
11
00
01
Fourth
Address
A1, A0
11
10
01
00
Fourth
Address
A1, A0
11
00
01
10
Table 3. ZZ Mode Electrical Characteristics
Parameter
IDDZZ
tZZS
tZZREC
tZZI
tRZZI
Description
Sleep mode standby current
Device operation to ZZ
ZZ recovery time
ZZ active to sleep current
ZZ Inactive to exit sleep current
Document Number: 38-05538 Rev. *K
Test Conditions
ZZ  VDD 0.2 V
ZZVDD  0.2 V
ZZ 0.2 V
This parameter is sampled
This parameter is sampled
Min
–
–
2tCYC
–
0
Max
50
2tCYC
–
2tCYC
–
Unit
mA
ns
ns
ns
ns
Page 9 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Truth Table
The Truth Table for CY7C1354C and CY7C1356C follows. [2, 3, 4, 5, 6, 7, 8]
Operation
Address
Used
CE ZZ
ADV/LD
WE
BWx
OE
CEN CLK
DQ
Deselect cycle
None
H
L
L
X
X
X
L
L-H
Tri-state
Continue deselect cycle
None
X
L
H
X
X
X
L
L-H
Tri-state
Read cycle (begin burst)
External
L
L
L
H
X
L
L
L-H
Data out (Q)
Next
X
L
H
X
X
L
L
L-H
Data out (Q)
Read cycle (continue burst)
NOP/dummy read (begin burst)
Dummy read (continue burst)
Write cycle (begin burst)
External
L
L
L
H
X
H
L
L-H
Tri-state
Next
X
L
H
X
X
H
L
L-H
Tri-state
External
L
L
L
L
L
X
L
L-H
Data in (D)
Write cycle (continue burst)
Next
X
L
H
X
L
X
L
L-H
Data in (D)
NOP/WRITE ABORT (begin burst)
None
L
L
L
L
H
X
L
L-H
Tri-state
WRITE ABORT (continue burst)
Next
X
L
H
X
H
X
L
L-H
Tri-state
IGNORE CLOCK EDGE (stall)
SLEEP MODE
Current
X
L
X
X
X
X
H
L-H
-
None
X
H
X
X
X
X
X
X
Tri-state
Partial Write Cycle Description
The following table lists the Partial Write Cycle Description for CY7C1354C.[2, 3, 4, 9]
Function (CY7C1354C)
WE
H
BWd
X
BWc
X
BWb
X
BWa
X
Write– no bytes written
L
H
H
H
H
Write byte a –(DQa and DQPa)
L
H
H
H
L
Read
Write byte b – (DQb and DQPb)
L
H
H
L
H
Write bytes b, a
L
H
H
L
L
Write byte c –(DQc and DQPc)
L
H
L
H
H
Write bytes c, a
L
H
L
H
L
Write bytes c, b
L
H
L
L
H
Write bytes c, b, a
L
H
L
L
L
Write byte d –(DQd and DQPd)
L
L
H
H
H
Write bytes d, a
L
L
H
H
L
Write bytes d, b
L
L
H
L
H
Write bytes d, b, a
L
L
H
L
L
Write bytes d, c
L
L
L
H
H
Write bytes d, c, a
L
L
L
H
L
Write bytes d, c, b
L
L
L
L
H
Write all bytes
L
L
L
L
L
Notes
2. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one bytewrite select is active, BWx = valid signifies
that the desired byte write selects are asserted, see Write Cycle Description table for details.
3. Write is defined by WE and BWX. See Write Cycle Description table for details.
4. When a write cycle is detected, all I/Os are tri-stated, even during byte writes.
5. The DQ and DQP pins are controlled by the current cycle and the OE signal.
6. CEN = H inserts wait states.
7. Device will power up deselected and the I/Os in a tri-state condition, regardless of OE.
8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQPX = tri-state when OE is
inactive or when the device is deselected, and DQs = data when OE is active.
9. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write will be done based on which byte write is active.
Document Number: 38-05538 Rev. *K
Page 10 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Partial Write Cycle Description
The following table lists the Partial Write Cycle Description for CY7C1356C.[10, 11, 12, 13]
Function (CY7C1356C)
WE
BWb
BWa
Read
H
x
x
Write – no bytes written
L
H
H
Write byte a (DQa and DQPa)
L
H
L
Write byte b – (DQb and DQPb)
L
L
H
Write both bytes
L
L
L
Notes
10. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for all chip enables active. BWx = L signifies at least one bytewrite select is active, BWx = valid signifies
that the desired byte write selects are asserted, see Write Cycle Description table for details.
11. Write is defined by WE and BWX. See Write Cycle Description table for details.
12. When a write cycle is detected, all I/Os are tri-stated, even during byte writes.
13. Table only lists a partial listing of the byte write combinations. Any combination of BWX is valid. Appropriate write will be done based on which byte write is active.
Document Number: 38-05538 Rev. *K
Page 11 of 32
[+] Feedback
CY7C1354C, CY7C1356C
IEEE 1149.1 Serial Boundary Scan (JTAG)
Test Access Port (TAP)
The CY7C1354C/CY7C1356C incorporates a serial boundary
scan test access port (TAP) in the BGA package only. The TQFP
package does not offer this functionality. This part operates in
accordance with IEEE Standard 1149.1-1900, but does not have
the set of functions required for full 1149.1 compliance. These
functions from the IEEE specification are excluded because their
inclusion places an added delay in the critical speed path of the
SRAM. Note that the TAP controller functions in a manner that
does not conflict with the operation of other devices using 1149.1
fully compliant TAPs. The TAP operates using JEDEC-standard
3.3 V or 2.5 V I/O logic levels.
Test Clock (TCK)
The CY7C1354C/CY7C1356C contains a TAP controller,
instruction register, boundary scan register, bypass register, and
ID register.
Test Data-In (TDI)
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternately be connected to VDD through a pull up resistor. TDO
should be left unconnected. Upon power-up, the device comes
up in a reset state which does not interfere with the operation of
the device.
TAP Controller State Diagram
1
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to leave
this ball unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
The TDI ball is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. TDI is internally pulled
up and can be unconnected if the TAP is unused in an
application. TDI is connected to the most significant bit (MSB) of
any register. (See the TAP Controller Block Diagram.)
Test Data-Out (TDO)
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current state
of the TAP state machine. The output changes on the falling edge
of TCK. TDO is connected to the least significant bit (LSB) of any
register. (See the TAP Controller State Diagram.)
TAP Controller Block Diagram
TEST-LOGIC
RESET
0
0
RUN-TEST/
IDLE
1
SELECT
DR-SCA N
1
SELECT
IR-SCAN
0
1
2 1 0
CAPTURE-IR
0
SHIFT-DR
0
TDI
SHIFT-IR
1
1
1
0
PAUSE-IR
1
Selection
Circuitry
TDO
x . . . . . 2 1 0
Boundary Scan Register
0
PAUSE-DR
Instruction Register
Identification Register
EXIT1-IR
0
Selection
Circuitry
31 30 29 . . . 2 1 0
0
1
EXIT1-DR
0
1
EXIT2-DR
0
EXIT2-IR
1
0
TAP CONTROLLER
UPDATE-IR
1
0
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
Document Number: 38-05538 Rev. *K
TCK
TM S
1
UPDATE-DR
1
Bypass Register
0
1
CAPTURE-DR
0
0
0
1
Performing a TAP Reset
A RESET is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
At power-up, the TAP is reset internally to ensure that TDO
comes up in a high Z state.
Page 12 of 32
[+] Feedback
CY7C1354C, CY7C1356C
TAP Registers
Registers are connected between the TDI and TDO balls and
enable data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction register. Data is serially loaded into the TDI ball
on the rising edge of TCK. Data is output on the TDO ball on
the falling edge of TCK.
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the
TDI and TDO balls as shown in the TAP Controller Block
Diagram on page 12. Upon power up, the instruction register
is loaded with the IDCODE instruction. It is also loaded with
the IDCODE instruction if the controller is placed in a reset
state as described in the previous section.
When the TAP controller is in the Capture-IR state, the two
least significant bits are loaded with a binary “01” pattern to
enable fault isolation of the board-level serial test data path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This enables data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
(VSS) when the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The boundary scan register is loaded with the contents of the
RAM I/O ring when the TAP controller is in the Capture-DR
state and is then placed between the TDI and TDO balls when
the controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used
to capture the contents of the I/O ring.
The tables Boundary Scan Exit Order (256 K × 36) on page 17
and Boundary Scan Exit Order (512 K × 18) on page 18 show
the order in which the bits are connected. Each bit
corresponds to one of the bumps on the SRAM package. The
MSB of the register is connected to TDI and the LSB is
connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in Identification Register
Definitions on page 15.
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in the
Instruction Codes table. Three of these instructions are listed
as RESERVED and should not be used. The other five
instructions are described in detail in this section.
Document Number: 38-05538 Rev. *K
The TAP controller used in this SRAM is not fully compliant to
the 1149.1 convention because some of the mandatory 1149.1
instructions are not fully implemented.
The TAP controller cannot be used to load address data or
control signals into the SRAM and cannot preload the I/O
buffers. The SRAM does not implement the 1149.1 commands
EXTEST or INTEST or the PRELOAD portion of
SAMPLE/PRELOAD; rather, it performs a capture of the I/O
ring when these instructions are executed.
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed between
TDI and TDO. During this state, instructions are shifted
through the instruction register through the TDI and TDO balls.
To execute the instruction once it is shifted in, the TAP
controller needs to be moved into the Update-IR state.
EXTEST
EXTEST is a mandatory 1149.1 instruction which is to be
executed whenever the instruction register is loaded with all
0s. EXTEST is not implemented in this SRAM TAP controller,
and therefore this device is not compliant to 1149.1. The TAP
controller does recognize an all-0 instruction.
When an EXTEST instruction is loaded into the instruction
register, the SRAM responds as if a SAMPLE/PRELOAD
instruction has been loaded. There is one difference between
the two instructions. Unlike the SAMPLE/PRELOAD
instruction, EXTEST places the SRAM outputs in a high Z
state.
IDCODE
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and
enables the IDCODE to be shifted out of the device when the
TAP controller enters the Shift-DR state.
The IDCODE instruction is loaded into the instruction register
upon power up or whenever the TAP controller is given a test
logic reset state.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register
to be connected between the TDI and TDO balls when the TAP
controller is in a Shift-DR state. It also places all SRAM outputs
into a High-Z state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is
captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because
there is a large difference in the clock frequencies, it is
possible that during the Capture-DR state, an input or output
undergo a transition. The TAP may then try to capture a signal
while in transition (metastable state). This does not harm the
device, but there is no guarantee as to the value that will be
captured. Repeatable results may not be possible.
Page 13 of 32
[+] Feedback
CY7C1354C, CY7C1356C
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture setup plus hold
times (tCS and tCH). The SRAM clock input might not be captured
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the CK and CK# captured in the boundary scan register.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
PRELOAD enables an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells prior
to the selection of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required - that is, while data captured
is shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO balls. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
TAP Timing
1
2
Test Clock
(TCK )
3
t TH
t TM SS
t TM SH
t TDIS
t TDIH
t
TL
4
5
6
t CY C
Test M ode Select
(TM S)
Test Data-In
(TDI)
t TDOV
t TDOX
Test Data-Out
(TDO)
DON’T CA RE
UNDEFINED
TAP AC Switching Characteristics
Over the Operating Range[14, 15]
Parameter
Description
Clock
TCK clock cycle time
tTCYC
TCK clock frequency
tTF
TCK clock HIGH time
tTH
TCK clock LOW time
tTL
Output Times
TCK clock LOW to TDO valid
tTDOV
TCK clock LOW to TDO invalid
tTDOX
Setup Times
TMS setup to TCK clock rise
tTMSS
TDI setup to TCK clock rise
tTDIS
Capture setup to TCK rise
tCS
Hold Times
TMS hold after TCK clock rise
tTMSH
TDI hold after clock rise
tTDIH
Capture hold after clock rise
tCH
Min
Max
Unit
50
–
20
20
–
20
–
–
ns
MHz
ns
ns
–
0
10
–
ns
ns
5
5
5
–
–
–
ns
ns
ns
5
5
5
–
–
–
ns
ns
ns
Notes
14. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
15. Test conditions are specified using the load in TAP AC test Conditions. tR/tF = 1 ns.
Document Number: 38-05538 Rev. *K
Page 14 of 32
[+] Feedback
CY7C1354C, CY7C1356C
3.3 V TAP AC Test Conditions
2.5 V TAP AC Test Conditions
Input pulse levels ............................................... VSS to 3.3 V
Input pulse levels ................................................VSS to 2.5 V
Input rise and fall times ................................................... 1 ns
Input rise and fall time..................................................... 1 ns
Input timing reference levels ......................................... 1.5 V
Input timing reference levels........................................ 1.25 V
Output reference levels ................................................. 1.5 V
Output reference levels................................................ 1.25 V
Test load termination supply voltage ............................. 1.5 V
Test load termination supply voltage............................ 1.25 V
3.3 V TAP AC Output Load Equivalent
2.5 V TAP AC Output Load Equivalent
1.25V
1.5V
50Ω
50Ω
TDO
TDO
Z O= 50Ω
Z O= 50Ω
20pF
20pF
TAP DC Electrical Characteristics and Operating Conditions
(0 °C < TA < +70 °C; VDD = 3.3 V ± 0.165 V unless otherwise noted)[16]
Parameter
VOH1
VOH2
VOL1
VOL2
VIH
VIL
IX
Description
Test Conditions
Output HIGH voltage
Output HIGH voltage
Output LOW voltage
Output LOW voltage
Max
Unit
IOH = –4.0 mA, VDDQ = 3.3 V
2.4
–
V
IOH = –1.0 mA, VDDQ = 2.5 V
2.0
–
V
IOH = –100 µA
IOL = 8.0 mA
IOL = 100 µA
Input HIGH voltage
Input LOW voltage
Input load current
Min
VDDQ = 3.3 V
2.9
–
V
VDDQ = 2.5 V
2.1
–
V
VDDQ = 3.3 V
–
0.4
V
VDDQ = 2.5 V
–
0.4
V
VDDQ = 3.3 V
–
0.2
V
VDDQ = 2.5 V
–
0.2
V
VDDQ = 3.3 V
2.0
VDD + 0.3
V
VDDQ = 2.5 V
1.7
VDD + 0.3
V
VDDQ = 3.3 V
–0.3
0.8
V
VDDQ = 2.5 V
–0.3
0.7
V
–5
5
µA
GND < VIN < VDDQ
Identification Register Definitions
Instruction Field
CY7C1354C
Revision number (31:29)
Cypress device ID (28:12)[17]
000
01011001000100110
Cypress JEDEC ID (11:1)
ID register presence (0)
CY7C1356C
000
Description
Reserved for version number.
01011001000010110 Reserved for future use.
00000110100
00000110100
1
1
Allows unique identification of SRAM vendor.
Indicate the presence of an ID register.
Notes
16. All voltages referenced to VSS (GND).
17. Bit #24 is “1” in the Register Definitions for both 2.5 V and 3.3 V versions of this device.
Document Number: 38-05538 Rev. *K
Page 15 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Scan Register Sizes
Register Name
Bit Size (× 36)
Bit Size (× 18)
Instruction
3
3
Bypass
1
1
ID
32
32
Boundary scan order (119-ball BGA package)
69
69
Boundary scan order (165-ball FBGA package)
69
69
Identification Codes
Instruction
Code
Description
EXTEST
000 Captures the input/output ring contents. Places the boundary scan register between the TDI and
TDO. Forces all SRAM outputs to high Z state.
IDCODE
001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This
operation does not affect SRAM operation.
SAMPLE Z
010 Captures the input/output contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a high Z state.
RESERVED
011 Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100 Captures the input/output ring contents. Places the boundary scan register between TDI and TDO.
Does not affect the SRAM operation.
RESERVED
101 Do Not Use: This instruction is reserved for future use.
RESERVED
110 Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM operation.
Document Number: 38-05538 Rev. *K
Page 16 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Boundary Scan Exit Order (256 K × 36)
Bit #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
119-ball ID
K4
H4
M4
F4
B4
G4
C3
B3
D6
H7
G6
E6
D7
E7
F6
G7
H6
T7
K7
L6
N6
165-ball ID
B6
B7
A7
B8
A8
A9
B10
A10
C11
E10
F10
G10
D10
D11
E11
F11
G11
H11
J10
K10
L10
Bit #
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
22
23
24
25
26
27
28
29
30
P7
N7
M6
L7
K6
P6
T4
A3
C5
M10
J11
K11
L11
M11
N11
R11
R10
P10
52
53
54
55
56
57
58
59
60
61
Document Number: 38-05538 Rev. *K
119-ball ID
B5
A5
C6
A6
P4
N4
R6
T5
T3
R2
R3
P2
P1
L2
K1
N2
N1
M2
L1
K2
Not Bonded
(Preset to 1)
H1
G2
E2
D1
H2
G1
F2
E1
D2
C2
165-ball ID
R9
P9
R8
P8
R6
P6
R4
P4
R3
P3
R1
N1
L2
K2
J2
M2
M1
L1
K1
J1
Not Bonded
(Preset to 1)
G2
F2
E2
D2
G1
F1
E1
D1
C1
B2
Page 17 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Boundary Scan Exit Order (512 K × 18)
Bit #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
119-ball ID
K4
H4
M4
F4
B4
G4
C3
B3
T2
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
D6
E7
F6
G7
H6
T7
K7
L6
N6
P7
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
T6
A3
C5
B5
A5
C6
A6
P4
N4
165-ball ID
B6
B7
A7
B8
A8
A9
B10
A10
A11
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
C11
D11
E11
F11
G11
H11
J10
K10
L10
M10
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
R11
R10
P10
R9
P9
R8
P8
R6
P6
Document Number: 38-05538 Rev. *K
Bit #
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
119-ball ID
R6
T5
T3
R2
R3
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
P2
N1
M2
L1
K2
Not Bonded (Preset to 1)
H1
G2
E2
D1
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
C2
A2
E4
B2
Not Bonded (Preset to 0)
G3
Not Bonded (Preset to 0)
L5
B6
165-ball ID
R4
P4
R3
P3
R1
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
N1
M1
L1
K1
J1
Not Bonded (Preset to 1)
G2
F2
E2
D2
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
B2
A2
A3
B3
Not Bonded (Preset to 0)
Not Bonded (Preset to 0)
A4
B5
A6
Page 18 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage temperature ................................ –65 °C to +150 °C
Neutron Soft Error Immunity
Parameter
Ambient temperature with
power applied ........................................... –55 °C to +125 °C
Supply voltage on VDDQ relative to GND....... –0.5 V to +VDD
Unit
25 °C
320
368
FIT/
Mb
LMBU
Logical
multi-bit
upsets
25 °C
0
0.01
FIT/
Mb
Single event
latch-up
85 °C
0
0.1
FIT/
Dev
SEL
Static discharge voltage........................................... > 2001 V
(per MIL-STD-883, method 3015)
Max*
Logical
single-bit
upsets
DC input voltage .................................. –0.5 V to VDD + 0.5 V
Current into outputs (LOW) ......................................... 20 mA
Test Condi- Typ
tions
LSBU
Supply voltage on VDD relative to GND ........–0.5 V to +4.6 V
DC to outputs in tri-state ....................–0.5 V to VDDQ + 0.5 V
Description
* No LMBU or SEL events occurred during testing; this column represents a
statistical 2, 95% confidence limit calculation. For more details refer to
Application Note AN 54908 “Accelerated Neutron SER Testing and Calculation
of Terrestrial Failure Rates”.
Latch-up current ..................................................... > 200 mA
Operating Range
Range
Commercial
Industrial
Ambient
Temperature
VDD
VDDQ
0 °C to +70 °C
3.3 V– 5% /
+ 10%
2.5 V – 5%
to VDD
–40 °C to +85 °C
Electrical Characteristics
Over the Operating Range[18, 19]
Parameter
Description
Test Conditions
Min
Max
Unit
VDD
Power supply voltage
VDDQ
I/O supply voltage
3.135
3.6
V
for 3.3 V I/O
3.135
VDD
V
VOH
Output HIGH voltage
for 2.5 V I/O
for 3.3 V I/O, IOH =4.0 mA
2.375
2.625
V
2.4
–
V
for 2.5 V I/O, IOH =1.0 mA
2.0
–
V
VOL
Output LOW voltage
for 3.3 V I/O, IOL=8.0 mA
–
0.4
V
VIH
Input HIGH voltage
VIL
Input LOW voltage[20]
IX
Input leakage current
except ZZ and MODE
GND  VI  VDDQ
Input current of MODE
Input = VSS
Input = VDD
Input current of ZZ
Input = VSS
–
30
A
–5
5
A
for 2.5 V I/O, IOL=1.0 mA
–
0.4
V
2.0
VDD + 0.3 V
V
for 2.5 V I/O
1.7
VDD + 0.3 V
V
for 3.3 V I/O
–0.3
0.8
V
for 2.5 V I/O
–0.3
0.7
V
–5
5
A
–30
–
A
–
5
A
–5
–
A
for 3.3 V I/O
Input = VDD
IOZ
Output leakage current GND  VI  VDDQ, output disabled
Notes
18. Overshoot: VIH(AC) < VDD + 1.5 V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2 V (Pulse width less than tCYC/2).
19. TPower-up: Assumes a linear ramp from 0 V to VDD (min) within 200 ms. During this time VIH < VDD and VDDQ <VDD.
20. Tested initially and after any design or process changes that may affect these parameters.
Document Number: 38-05538 Rev. *K
Page 19 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Electrical Characteristics
Over the Operating Range[18, 19] (continued)
Parameter
Min
Max
Unit
4 ns cycle, 250 MHz
–
250
mA
5 ns cycle, 200 MHz
–
220
mA
6 ns cycle, 166 MHz
–
180
mA
Automatic CE
power-down
current—TTL inputs
Max VDD, device deselected, VIN 4 ns cycle, 250 MHz
 VIH or VIN  VIL,
5 ns cycle, 200 MHz
f = fMAX = 1/tCYC
6 ns cycle, 166 MHz
–
130
mA
–
120
mA
–
110
mA
ISB2
Automatic CE
power-down
current—CMOS inputs
Max VDD, device deselected,
All speed grades
VIN  0.3 V or VIN > VDDQ 0.3 V,
f=0
–
40
mA
ISB3
Automatic CE
power-down
current—CMOS inputs
Max VDD, device deselected,
4 ns cycle, 250 MHz
VIN  0.3 V or VIN > VDDQ 0.3 V, 5 ns cycle, 200 MHz
f = fMAX = 1/tCYC
6 ns cycle, 166 MHz
–
120
mA
–
110
mA
–
100
mA
Automatic CE
power-down
current—TTL inputs
Max VDD, device deselected,
VIN  VIH or VIN  VIL, f = 0
–
40
mA
IDD
ISB1
ISB4
Description
VDD operating supply
Test Conditions
VDD = Max, IOUT = 0 mA,
f = fMAX = 1/tCYC
All speed grades
Capacitance[21]
100 TQFP
Max
119 BGA
Max
165 FBGA
Max
Unit
Input capacitance
5
5
5
pF
CCLK
TA = 25 C, f = 1 MHz,
V
DD = 3.3 V VDDQ = 2.5 V
Clock input capacitance
5
5
5
pF
CI/O
Input/output capacitance
5
7
7
pF
Test Conditions
100 TQFP
Max
119 BGA
Max
165 FBGA
Max
Unit
Test conditions follow standard
test methods and procedures
for measuring thermal
impedance, per EIA/JESD51.
29.41
34.1
16.8
°C/W
6.13
14.0
3.0
°C/W
Parameter
CIN
Description
Test Conditions
Thermal Resistance[21]
Parameter
Description
JA
Thermal resistance
(junction to ambient)
JC
Thermal resistance
(junction to case)
Note
21. Tested initially and after any design or process changes that may affect these parameters.
Document Number: 38-05538 Rev. *K
Page 20 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Figure 4. AC Test Loads and Waveforms
3.3 V I/O Test Load
R = 317 
3.3 V
OUTPUT
OUTPUT
RL = 50 
Z0 = 50 
VT = 1.5 V
(a)
Z0 = 50 
VT = 1.25 V
(a)
Document Number: 38-05538 Rev. *K
R = 351 
10%
(c)
ALL INPUT PULSES
VDDQ
INCLUDING
JIG AND
SCOPE
 1 ns
(b)
GND
5 pF
R = 1538 
(b)
90%
10%
90%
 1 ns
R = 1667 
2.5 V
OUTPUT
RL = 50 
GND
5 pF
INCLUDING
JIG AND
SCOPE
2.5 V I/O Test Load
OUTPUT
ALL INPUT PULSES
VDDQ
10%
90%
10%
90%
 1 ns
 1 ns
(c)
Page 21 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Switching Characteristics
Over the Operating Range [22, 23]
Parameter
tPower[24]
Description
VCC (typical) to the first access read or write
–250
–200
–166
Unit
Min
Max
Min
Max
Min
Max
1
–
1
–
1
–
ms
4.0
–
5
–
6
–
ns
Clock
tCYC
Clock cycle time
FMAX
Maximum operating frequency
–
250
–
200
–
166
MHz
tCH
Clock HIGH
1.8
–
2.0
–
2.4
–
ns
tCL
Clock LOW
1.8
–
2.0
–
2.4
–
ns
tEOV
OE LOW to output valid
–
2.8
–
3.2
–
3.5
ns
tCLZ
Z[25, 26, 27]
1.25
–
1.5
–
1.5
–
ns
Clock to low
Output Times
tCO
Data output valid after CLK rise
–
2.8
–
3.2
–
3.5
ns
tEOV
OE LOW to output valid
–
2.8
–
3.2
–
3.5
ns
tDOH
Data output hold after CLK rise
1.25
–
1.5
–
1.5
–
ns
tCHZ
Clock to high Z[25, 26, 27]
1.25
2.8
1.5
3.2
1.5
3.5
ns
tCLZ
Clock to low Z[25, 26, 27]
tEOHZ
tEOLZ
1.25
–
1.5
–
1.5
–
ns
Z[25, 26, 27]
–
2.8
–
3.2
–
3.5
ns
[25, 26, 27]
0
–
0
–
0
–
ns
OE HIGH to output high
OE LOW to output low Z
Setup Times
tAS
Address setup before CLK rise
1.4
–
1.5
–
1.5
–
ns
tDS
Data input setup before CLK rise
1.4
–
1.5
–
1.5
–
ns
tCENS
CEN setup before CLK rise
1.4
–
1.5
–
1.5
–
ns
tWES
WE, BWx setup before CLK rise
1.4
–
1.5
–
1.5
–
ns
tALS
ADV/LD setup before CLK rise
1.4
–
1.5
–
1.5
–
ns
tCES
Chip select setup
1.4
–
1.5
–
1.5
–
ns
tAH
Address hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
tDH
Data input hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
tCENH
CEN hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
Hold Times
tWEH
WE, BWx hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
tALH
ADV/LD hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
tCEH
Chip select hold after CLK rise
0.4
–
0.5
–
0.5
–
ns
Notes
22. Timing reference level is 1.5 V when VDDQ = 3.3 V and is 1.25 V when VDDQ = 2.5 V.
23. Test conditions shown in (a) of Figure 4 on page 21 unless otherwise noted.
24. This part has a voltage regulator internally; tpower is the time power needs to be supplied above VDD minimum initially, before a Read or Write operation can be
initiated.
25. tCHZ, tCLZ, tEOLZ, and tEOHZ are specified with AC test conditions shown in (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
26. At any given voltage and temperature, tEOHZ is less than tEOLZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve high Z prior to low Z under the same system conditions.
27. This parameter is sampled and not 100% tested.
Document Number: 38-05538 Rev. *K
Page 22 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Switching Waveforms
Figure 5. Read/Write Timing[28, 29, 30]
1
2
3
t CYC
4
5
6
A3
A4
7
8
9
A5
A6
10
CLK
t CENS
t CENH
t CES
t CEH
t CL
t CH
CEN
CE
ADV/LD
WE
BW x
A1
ADDRESS
A2
A7
t CO
t AS
t DS
t AH
Data
In-Out (DQ)
t DH
D(A1)
t CLZ
D(A2)
D(A2+1)
t DOH
Q(A3)
t OEV
Q(A4)
t CHZ
Q(A4+1)
D(A5)
Q(A6)
t OEHZ
t DOH
t OELZ
OE
WRITE
D(A1)
WRITE
D(A2)
BURST
WRITE
D(A2+1)
READ
Q(A3)
DON’T CARE
READ
Q(A4)
BURST
READ
Q(A4+1)
WRITE
D(A5)
READ
Q(A6)
WRITE
D(A7)
DESELECT
UNDEFINED
Notes
28. For this waveform ZZ is tied low.
29. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
30. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document Number: 38-05538 Rev. *K
Page 23 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Switching Waveforms (continued)
Figure 6. NOP, STALL, and DESELECT Cycles[31, 32, 33]
1
2
A1
A2
3
4
5
A3
A4
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BWx
ADDRESS
A5
t CHZ
D(A1)
Data
Q(A2)
D(A4)
Q(A3)
Q(A5)
In-Out (DQ)
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
DON’T CARE
STALL
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
UNDEFINED
Notes
31. For this waveform ZZ is tied low.
32. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
33. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle.
Document Number: 38-05538 Rev. *K
Page 24 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Switching Waveforms (continued)
Figure 7. ZZ Mode Timing[34, 35]
CLK
t ZZ
ZZ
I
t
t ZZREC
ZZI
SUPPLY
I DDZZ
t RZZI
A LL INPUTS
DESELECT or READ Only
(except ZZ)
Outputs (Q)
High-Z
DON’T CARE
Notes
34. Device must be deselected when entering ZZ mode. See cycle description table for all possible signal conditions to deselect the device.
35. I/Os are in high Z when exiting ZZ sleep mode.
Document Number: 38-05538 Rev. *K
Page 25 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Ordering Information
The table below contains only the parts that are currently available. If you don’t see what you are looking for, please contact your local
sales representative. For more information, visit the Cypress website at www.cypress.com and refer to the product summary page at
http://www.cypress.com/products
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office
closest to you, visit us at http://www.cypress.com/go/datasheet/offices
Speed
(MHz)
166
Ordering Code
CY7C1354C-166AXC
Package
Diagram
Part and Package Type
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
Operating
Range
Commercial
CY7C1356C-166AXC
CY7C1354C-166BGC
51-85115 119-ball Ball Grid Array (14 × 22 × 2.4 mm)
CY7C1356C-166BGC
CY7C1354C-166AXI
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
Industrial
CY7C1354C-200AXC
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
Commercial
CY7C1354C-200BGC
51-85115 119-ball Ball Grid Array (14 × 22 × 2.4 mm)
CY7C1354C-200AXI
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
Industrial
CY7C1354C-250AXC
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
Commercial
CY7C1356C-166AXI
200
250
CY7C1356C-250AXC
Ordering Code Definitions
CY
7C 135X C - XXX XX X
Temperature Range: X = C or I
C = Commercial
I = Industrial
Package Type: XX = AX or BG
AX = 100-pin Thin Quad Flat Pack (Pb-free)
BG = 119-ball Ball Grid Array
Speed Grade:
XXX = 166 MHz / 200 MHz / 250 MHz
Process Technology  90 nm
135X = 1354 or 1356
1354 = PL, 256 Kb × 36 (9 Mb)
1356 = PL, 512 Kb × 18 (9 Mb)
Marketing Code: 7C = SRAMs
Company ID: CY = Cypress
Document Number: 38-05538 Rev. *K
Page 26 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Package Diagrams
Figure 8. 100-pin Thin Plastic Quad Flatpack (14 × 20 × 1.4 mm), 51-85050
51-85050 *D
Document Number: 38-05538 Rev. *K
Page 27 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Figure 9. 119-ball BGA (14 × 22 × 2.4 mm), 51-85115
51-85115 *C
Document Number: 38-05538 Rev. *K
Page 28 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Figure 10. 165-ball FBGA (13 × 15 × 1.4 mm), 51-85180
51-85180 *C
Document Number: 38-05538 Rev. *K
Page 29 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Acronyms
Document Conventions
Acronym
Description
Units of Measure
BGA
ball grid array
CMOS
complementary metal oxide semiconductor
ns
nano seconds
Symbol
Unit of Measure
CE
chip enable
V
Volts
CEN
clock enable
µA
micro Amperes
FPBGA
fine-pitch ball grid array
mA
milli Amperes
JTAG
Joint Test Action Group
ms
milli seconds
NoBL
No Bus Latency
MHz
Mega Hertz
OE
output enable
pF
pico Farad
SRAM
static random access memory
W
Watts
TCK
test clock
°C
degree Celcius
TDI
test data input
TMS
test mode select
TDO
test data output
TQFP
thin quad flat pack
WE
write enable
Document Number: 38-05538 Rev. *K
Page 30 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Document History Page
Document Title: CY7C1354C/CY7C1356C 9-Mbit (256 K × 36/512 K × 18) Pipelined SRAM with NoBL™ Architecture
Document Number: 38-05538
REV.
ECN No.
Submission
Date
Orig. of
Change
Description of Change
**
242032
See ECN
RKF
New data sheet
*A
278130
See ECN
RKF
Changed Boundary Scan order to match the B Rev of these devices
Changed TQFP pkg to Lead-free TQFP in Ordering Information section
Added comment of Lead-free BG and BZ packages availability
*B
284431
See ECN
VBL
Changed ISB1 and ISB3 from DC Characteristic table as follows
ISB1: 225 mA-> 130 mA, 200 MHz -> 120 mA, 167 MHz -> 110 mA
ISB3: 225 MHz -> 120 mA, 200 MHz -> 110 mA, 167 MHz -> 100 mA
Add BG and BZ pkg lead-free part numbers to ordering info section
*C
320834
See ECN
PCI
Changed 225 MHz to 250 MHz
Address expansion pins/balls in the pinouts for all packages are modified as
per JEDEC standard
Unshaded frequencies of 250, 200, 166 MHz in AC/DC Tables and Selection
Guide
Changed JA and JC for TQFP Package from 25 and 9 C/W to 29.41 and
6.13 C/W respectively
Changed JA and JC for BGA Package from 25 and 6 C/W to 34.1 and 14.0
C/W respectively
Changed JA and JC for FBGA Package from 27 and 6 C/W to 16.8 and 3.0
C/W respectively
Modified VOL, VOH test conditions
Added Lead-Free product information
Updated Ordering Information Table
Changed from Preliminary to Final
*D
351895
See ECN
PCI
Changed ISB2 from 35 to 40 mA
Updated Ordering Information Table
*E
377095
See ECN
PCI
Modified test condition in note# 15 from VDDQ < VDD to VDDQ  VDD
*F
408298
See ECN
RXU
Changed address of Cypress Semiconductor Corporation on Page# 1 from
“3901 North First Street” to “198 Champion Court”
Changed three-state to tri-state.
Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in the
Electrical Characteristics Table.
Replaced Package Name column with Package Diagram in the Ordering Information table.
*G
501793
See ECN
VKN
Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND
Changed tTH, tTL from 25 ns to 20 ns and tTDOV from 5 ns to 10 ns in TAP AC
Switching Characteristics table.
Updated the Ordering Information table.
*H
2756340
08/26/2009 VKN/AESA Updated template
Included Soft Error Immunity Data
Modified Ordering Information table by including parts that are available and
modified the disclaimer for the Ordering information.
*I
3033272
09/19/2010
*J
3052882
10/08/2010
NJY
Removed obsolete part numbers.
*K
3186089
03/02/2011
NJY
Updated Ordering Information.
Updated Package Diagrams.
Document Number: 38-05538 Rev. *K
NJY
Added Ordering Code Definitions.
Updated Package Diagrams.
Added Acronyms and Units of Measure.
Minor edits and updated in new template.
Page 31 of 32
[+] Feedback
CY7C1354C, CY7C1356C
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
cypress.com/go/memory
cypress.com/go/image
PSoC
cypress.com/go/psoc
Touch Sensing
cypress.com/go/touch
USB Controllers
Wireless/RF
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2006-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 38-05538 Rev. *K
Revised March 2, 2011
Page 32 of 32
No Bus Latency and NoBL are trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback