EXTECH HW30

HW30 Heat Watch Patent Pending
Description
1. Start/Stop
2. Mode
3. Recall
4. Lap/Split
5. LCD Display
Cautions
• This device is not a toy and must not reach children’s hands. It contains hazardous
objects as well as small parts that the children could swallow. In case a child
swallows any of them, please contact a physician immediately
• Do not leavethe battery and packing material lying around unattended; they can be
dangerous for children if they use them as toys
• In case the device is going to be unused for an extended period of time, remove the
battery to prevent them from draining
Operation
Mode Selection
The HW30 Heat
Watch has six
different
operating
modes.
Press the
MODE button to
switch from one
mode to
another.
The HW30 will remain in the Heat Index mode for two minutes and then default back to the
clock mode.
Time Date Mode
• Expired or damaged batteries can cause cauterization on contact with the skin.
Always, therefore, use suitable hand gloves in such cases
The time date display shows current time, day of week,
date and month. Also displayed are the alarm and heat
index alarm
indicators when they are activated.
• See that the battery are not short-circuited. Do not throw the battery into a fire.
Time and date set
Battery Replacement
Remove the screws from the back of the watch to open unit and battery compartment. The
battery is a Round Button cell Type CR2032. Removing and replacing the battery will
cause loss of all previous settings. Make sure the gasket seal is properly placed before
replacing back cover and tightening screws.
Specifications
Accuracy (Watch)
±5 seconds/24 hours
Accuracy (RH)
±5% (33 to 75% RH), ±7% (1 to 32% and 76 to 99%)
Accuracy (Temp)
±3°F (1.5°C)
Temperature
14 to 122°F (-10 to 50°C)
Resolution
0.1/ 1o C or F
Update Rate
5 seconds in Heat Index Mode, 2 minutes in other modes
Heat Index
70 to 122°F (22 to 50°C)
Humidity
1 to 99% RH
Memory
30 Laps/ 30 Splits
LAP Counter
99 Laps
Battery
CR2032
Dimensions
3.1x2.6x0.8" (79x66x23mm)
Weight
3 oz. (85g) with battery
Calibration and Repair Services
Extech offers repair and calibration services for the products we sell. Extech also
provides NIST certification for most products. Call the Customer Care Department for
information on calibration services available for this product. Extech recommends that
annual calibrations be performed to verify meter performance and accuracy.
Support line (781) 890-7440
Technical Support: Extension 200; E-mail: [email protected]
Repair & Returns: Extension 210; E-mail: [email protected]
Product specifications subject to change without notice
For the latest version of this User Guide, Software updates, and other
up-to-the-minute product information, visit our website: www.extech.com
Extech Instruments Corporation, 285 Bear Hill Road, Waltham, MA 02451
Press and hold the RECALL button for 3 seconds to set
time and date.
Press START to zero seconds.
Press LAP to select minutes, Press START to change
minutes.
Press LAP to select hours, Press START to change hours.
Press LAP to select minutes, Press START to change minutes.
Press LAP to select year, Press START to change year.
Press LAP to select month, Press START to change month.
Press LAP to select date, Press START to change date.
Press LAP to select 12H/24H, Press START to change.
Press RECALL to exit time set mode.
The HW30 will return to display mode after 30 seconds of inactivity.
SETTING UNITS OF MEASURE
From heat index mode screen, Press LAP to change unit of measure (°F or °C)
HEAT INDEX MODE
In heat index mode the HW 30
displays relative humidity and
ambient temperature
(in °F or °C). Using these two
readings, the HW30 also
calculates and displays the
Heat Index.
HEAT INDEX ALARM SET
The HW30 Heat Watch has a user settable heat index alarm. The Heat Watch will emit a
20 second audible warning when the heat index reaches the level previously set by the
user.
To set the alarm
From heat index mode screen, Press and hold RECALL for 3 seconds
Press START to scroll up or LAP to scroll down
Press RECALL to save and exit setup mode, Or Press START if the alarm level has
already been set
The alarm can be stopped by pressing any of the four buttons.
STOPWATCH LAP MODE
Before using be sure to reset
stopwatch to 0.00.00.00.
The HW30 Heat Watch lap mode
has advanced features that will
make the timing of events or training
sessions easier and more enjoyable.
1. Lap Indicator
The lap indicator flashes to
indicate the lap in progress up to
99 laps.
When LAP is pushed, the lap
indicator and lap time displays
(top line of display) freeze for ten
seconds before resuming and
displaying next lap. Bottom
display always shows cumulative
time
2. Fastest Lap/Slowest
Lap/Average Lap Recall
Once timing session is complete,
press RECALL button to review
fastest lap, slowest lap and
average lap times. (based on 99
laps)
Then press START to review
individual lap times. (30 laps)
Lap times are shown on top line
of the display.
Split times are shown on the bottom line of the display.
3. Memory
The HW30 Heat Watch memory can store up to 30 lap (and split) times.
STOPWATCH SPLIT MODE
Before using be sure to reset stopwatch to
0.00.00.00.
The HW30 Heat Watch split mode has
advanced features that will make the
timing of events or training sessions easier
and more enjoyable.
1. Split time indicator
When SPLIT is pushed the split
indicator and split time displays (top
line of display) freeze to indicate the
current split time. Bottom display
continues to always show cumulative
time.
2. Fastest Lap/Slowest Lap/Average
Lap Recall
Once timing session is complete,
press RECALL button to review
fastest lap, slowest lap and average
lap times. (based on 99 laps)
Then press START to review split
times. (30 splits)
Split times are shown on the bottom
line of the display. Lap times are
shown on top line of the display.
3. Memory
The HW30 Heat Watch memory can store up to 30 split (and lap) times.
Timer MODE
The HW30 Heat Watch timer
mode is a user programmable
countdown timer.
The maximum count down time
is 9 hours 59 minutes and 59
seconds. The minimum settable
time is 1 second.
Press START to begin the
countdown
Press STOP to stop the
countdown
The timer will count down for the
selected duration.
The watch will emit an audible warning during the final 5 seconds of
the countdown.
The countdown will repeat itself until stopped by the user. The
countdown sequence will repeat itself and increment the timer count
by one each time it resumes.
The alarm can be stopped by pressing any of the buttons
ALARM MODE
The alarm will ring for 30
seconds.
Warranty
EXTECH INSTRUMENTS CORPORATION (a FLIR company)warrants this
instrument to be free of defects in parts and workmanship for one year from date of
shipment (a six month limited warranty applies on sensors and cables). If it should
become necessary to return the instrument for service during or beyond the
warranty period, contact the Customer Service Department at (781) 890-7440 ext.
210 for authorization or visit our website at www.extech.com (click on ‘Contact
Extech’ and go to ‘Service Department’ to request an RA number). A Return
Authorization (RA) number must be issued before any product is returned to Extech.
The sender is responsible for shipping charges, freight, insurance and proper
packaging to prevent damage in transit. This warranty does not apply to defects
resulting from action of the user such as misuse, improper wiring, operation outside
of specification, improper maintenance or repair, or unauthorized modification.
Extech specifically disclaims any implied warranty of merchantability or fitness for a
specific purpose and will not be liable for any direct, indirect, incidental or
consequential damages. Extech's total liability is limited to repair or replacement of
the product. The warranty set forth above is inclusive and no other warranty,
whether written or oral, is expressed or implied.
Copyright © 2008 Extech Instruments Corporation (a FLIR company). All rights
reserved including the right of reproduction in whole or in part in any form.
www.extech.com
HW30-EU v3.0 7/08