LT3689/LT3689-5 700mA Step-Down Regulator with Power-On Reset and Watchdog Timer DESCRIPTION FEATURES n n n n n n n n n n n Wide Input Range: Operation from 3.6V to 36V Overvoltage Lockout Protects Circuits through 60V Transients 85μA IQ at 12VIN to 3.3VOUT Low Ripple Burst Mode® Operation Allows Output Ripple <15mVP-P Programmable, Defeatable Watchdog Timer with Window or Timeout Control Programmable Power-On Reset Timer (POR) Synchronizable, Adjustable 350kHz to 2.2MHz Switching Frequency 700mA Output Switching Regulator with Internal Power Switch Fixed 5V or Adjustable Output Voltage 800mV Feedback Voltage Programmable Input Undervoltage Lockout with Hysteresis 16-Pin 3mm × 3mm QFN and 16-Pin MSOP Packages The LT®3689 is an adjustable frequency (350kHz to 2.2MHz) monolithic step-down switching regulator with a power-on reset and watchdog timer. The regulator operates from inputs up to 36V and withstands transients up to 60V. Low ripple Burst Mode® operation maintains high efficiency at low output current while keeping output ripple below 15mV in a typical application, with input quiescent current of just 85μA. Shutdown circuitry reduces input supply current to less than 1μA while EN/UVLO is pulled low. Using a resistor divider on the EN/UVLO pin provides a programmable undervoltage lockout. Current limit, frequency foldback and thermal shutdown provide fault protection. The reset and watchdog timeout periods are independently adjustable using external capacitors. Tight accuracy specifications and glitch immunity ensure reliable reset operation of a system without false triggering. The open collector RST will pull down if output voltage drops 10% below the programmed value. The watchdog timer is pin-selectable for window or timeout modes. In timeout mode, WDO pulls low if too long of a period passes before a watchdog transition is detected. In window mode, the LT3689 monitors for WDI falling edges grouped too close together or too far apart. APPLICATIONS n n Automotive Electronic Control Units Industrial Power Supplies L, LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Efficiency 3.3V Regulator with Power-On Reset Timer and Watchdog Timer 2.2μF VIN EN/UVLO μP I/O WDI I/O WDO RESET CWDT 10nF tWDU = 182ms tWDL = 5.9ms CWDT CPOR GND DA FB RT SYNC 12μH 10pF LT3689 RST CPOR 68nF tRST = 157ms 0.1μF SW 3.3V 700mA 316k 20.5k 22μF 100k 1000 VIN = 12V 80 VOUT = 3.3V f = 700kHz 70 L = 12μH TA = 25°C 60 100 50 40 30 10 POWER LOSS (mW) OUT BST EFFICIENCY (%) VIN 4.5V TO 36V TRANSIENT TO 60V 90 20 10 fSW = 700kHz 3689 TA01 0 0.0001 0.001 0.01 0.1 LOAD CURRENT (A) 1 1 3689 TA01b 3689fa 1 LT3689/LT3689-5 ABSOLUTE MAXIMUM RATINGS (Note 1) VIN, EN/UVLO Voltage (Note 2) .................................60V BST Voltage ..............................................................60V BST Above SW Voltage .............................................30V OUT, WDE Voltage .....................................................30V FB, RT, SYNC, W/T, WDI, RST, WDO Voltage ...............6V CWDT, CPOR Voltage.....................................................3V Operating Junction Temperature Range (Note 3) LT3689E ............................................. –40°C to 125°C LT3689I .............................................. –40°C to 125°C LT3689H ............................................ –40°C to 150°C Storage Temperature Range................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) MSOP ............................................................... 300°C PIN CONFIGURATION TOP VIEW RST WDI W/T WDE FB EN/UVLO DA SW CPOR RT BST 1 11 WDO 17 10 RST SW 3 DA 4 9 WDI 5 6 7 8 W/T MSE PACKAGE 16-LEAD PLASTIC MSOP θJA = 43°C/W, θJC = 4.3°C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB 12 CWDT VIN 2 WDE 17 16 15 14 13 16 15 14 13 12 11 10 9 FB 1 2 3 4 5 6 7 8 EN/UVLO WDO CWDT CPOR RT SYNC OUT BST VIN SYNC OUT TOP VIEW UD PACKAGE 16-LEAD (3mm s 3mm) PLASTIC QFN θJA = 68°C/W, θJC = 4.2°C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3689EMSE#PBF LT3689EMSE#TRPBF 3689 16-Lead Plastic MSOP with Exposed Pad –40°C to 125°C LT3689IMSE#PBF LT3689IMSE#TRPBF 3689 16-Lead Plastic MSOP with Exposed Pad –40°C to 125°C LT3689HMSE#PBF LT3689HMSE#TRPBF 3689 16-Lead Plastic MSOP with Exposed Pad –40°C to 150°C LT3689EMSE-5#PBF LT3689EMSE-5#TRPBF 36895 16-Lead Plastic MSOP with Exposed Pad –40°C to 125°C LT3689IMSE-5#PBF LT3689IMSE-5#TRPBF 36895 16-Lead Plastic MSOP with Exposed Pad –40°C to 125°C LT3689HMSE-5#PBF LT3689HMSE-5#TRPBF 36895 16-Lead Plastic MSOP with Exposed Pad –40°C to 150°C LT3689EUD#PBF LT3689EUD#TRPBF LDND 16-Lead (3mm × 3mm) Plastic QFN –40°C to 125°C LT3689IUD#PBF LT3689IUD#TRPBF LDND 16-Lead (3mm × 3mm) Plastic QFN –40°C to 125°C LT3689EUD-5#PBF LT3689EUD-5#TRPBF LFFM 16-Lead (3mm × 3mm) Plastic QFN –40°C to 125°C LT3689IUD-5#PBF LT3689IUD-5#TRPBF LFFM 16-Lead (3mm × 3mm) Plastic QFN –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3689fa 2 LT3689/LT3689-5 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C. VIN = 12V, VOUT = 5V, unless otherwise noted. (Note 3) SYMBOL PARAMETER CONDITIONS MIN VIN Fixed Undervoltage Lockout l VIN Overvoltage Lockout l 36 TYP MAX UNITS 3.4 3.7 V 38 40 V Quiescent Current from VIN VEN/UVLO = 0.3V VOUT = 3V, Not Switching VOUT = 0V, Not Switching l 0.01 50 125 0.5 95 175 μA μA μA Quiescent Current from OUT VEN/UVLO = 0.3V VOUT = 3V, Not Switching (Note 7) VOUT = 0V, Not Switching l 0.01 75 –5 0.5 150 –20 μA μA μA LT3689-5 Quiescent Current from VIN VEN/UVLO = 0.3V VOUT = 5.5V (Note 8) VOUT = 0V l 0.01 50 125 0.5 95 175 μA μA μA LT3689-5 Quiescent Current from OUT VEN/UVLO = 0.3V VOUT = 5.5V l 8 95 16 150 μA μA LT3689 FB Voltage LT3689-5 Output Voltage l 0.790 0.780 0.800 0.812 0.812 V V l 4.950 4.900 5.000 5.050 5.100 V V –30 –100 nA l LT3689 FB Pin Bias Current VFB = 0.800V LT3689 FB Voltage Line Regulation 5V < VIN < 36V 0.005 %/V LT3689-5 Output Voltage Line Regulation 5.5V < VIN < 36V 0.005 %/V fSW Switching Frequency RT = 4.02k RT = 31.62k tSW(OFF) Switch Off-Time VBST = 12V Foldback Frequency RT = 4.22k, VOUT = 0V 1.84 420 1.15 ISW = 0.8A 160 ns 1.55 kHz 1.95 A mV μA 1.2 1.5 A 0.1 5 μA 1.8 2.5 V 15 25 mA 1.150 1.260 1.350 V VEN/UVLO = 1.35V VEN/UVLO = 1.15V 2.5 0. 01 4.1 1 5.5 μA μA I(VEN/UVLO = 1.35V) – I(VEN/UVLO = 1.15V) 2.8 3.8 4.8 μA V 0.85 VBST = 12V, VOUT = 0V ISW = 0.8A EN/UVLO Threshold Voltage EN/UVLO Pin Current Hysteresis 120 1 Minimum BST Above SW Voltage EN/UVLO Pin Current MHz kHz 0.01 DA Current Limit BST Pin Current 2.16 540 450 Switch Leakage Current Boost Schottky Reverse Leakage 2 500 250 l Switch Current Limit (Note 4) Switch VCESAT l l SYNC Threshold Voltage 0.4 0.8 1 l VRST Reset Threshold as % of VFB 88 90 92 % tRST Reset Timeout Period CPOR = 8200pF l 17 19 21 ms tWDU Watchdog Upper Boundary CWDT = 1000pF l 17 19 21 ms tWDL Watchdog Lower Boundary CWDT = 1000pF l 610 675 785 μs VOL RST, WDO Output Voltage Low ISINK = 2.5mA, VOUT = 0V ISINK = 100μA, VOUT = 0V l l 0.15 0.05 0.4 0.3 V V VOH RST, WDO Output Voltage High (Note 6) l VOUT –1 V 3689fa 3 LT3689/LT3689-5 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C. VIN = 12V, VOUT = 5V, unless otherwise noted. (Note 3) SYMBOL PARAMETER CONDITIONS tUV UV Detect to RST Asserted Step VFB from 0.9V to 0.5V WDI Input Threshold MIN TYP MAX l 10 30 65 μs l 0.4 0.95 1.15 V WDI Input Pull-Up Current UNITS –2 WDI Input Pulse Width l 300 W/T Threshold Voltage l 0.4 W/T Input Pull-Down Current μA ns 0.8 1 V 2.6 WDE Threshold Voltage l μA 0.4 0.8 WDO Pull-Up Current (Note 6) –0.6 –0.85 μA RST Pull-Up Current (Note 6) –0.6 –0.85 μA Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Absolute maximum voltage at VIN and EN/UVLO pins is 60V for nonrepetitive 1 second transients, and 36V for continuous operation. Note 3: The LT3689E is guaranteed to meet performance specifications from 0°C to 125°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LT3689I is guaranteed over the full –40°C to 125°C operating junction temperature range. The LT3689H is guaranteed over the full –40°C to 150°C operating junction temperature range. High junction temperatures degrade operating lifetimes. Operating lifetime is derated at junction temperatures greater than 125°C. 1 V Note 4: Current limit is guaranteed by design and/or correlation to static test. Slope compensation reduces current limit at higher duty cycles. Note 5: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 150°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 6: The output of RST and WDO has a weak pull-up to VOUT of typically 1μA. However, external pull-up resistors may be used when faster rise times are required or for VOH higher than VOUT. Note 7: Polarity specification for all currents into pins is positive. All voltages are referenced to GND unless otherwise specified. Note 8: For the LT3689-5, VOUT is set to 5.5V to ensure the switching. TYPICAL PERFORMANCE CHARACTERISTICS Efficiency, VOUT = 5V Efficiency, VOUT = 3.3V 90 90 VIN = 12V 85 VIN = 24V TA = 25°C f = 700kHz 85 80 75 Efficiency, VOUT = 1.8V 80 VIN = 24V 80 VIN = 32V 75 TA = 25°C f = 1MHz VIN = 5V 75 VIN = 12V EFFICIENCY (%) TA = 25°C f = 1MHz EFFICIENCY (%) EFFICIENCY (%) 95 VIN = 12V 70 65 60 VIN = 32V 70 70 65 0 0.1 0.2 0.3 0.4 0.5 LOAD CURRENT (A) 0.6 0.7 3689 G01 55 65 50 0 0.1 0.2 0.3 0.4 0.5 LOAD CURRENT (A) 0.6 0.7 3689 G02 0 0.1 0.2 0.3 0.4 0.5 LOAD CURRENT (A) 0.6 0.7 3689 G03 3689fa 4 LT3689/LT3689-5 TYPICAL PERFORMANCE CHARACTERISTICS No-Load Supply Current vs VIN No-Load Supply Current 800 TA = 25°C SUPPLY CURRENT (μA) SUPPLY CURRENT (μA) CATCH DIODE: DIODES INC. B140HB VIN = 12V VOUT = 3.3V 700 120 100 80 60 40 20 Maximum Load Current, 5VOUT 1.4 600 500 INCREASED SUPPLY CURRENT DUE TO CATCH DIODE LEAKAGE AT HIGH TEMPERATURE 400 300 200 0 5 10 15 20 25 30 0 –50 –25 40 35 1.0 0.8 MINIMUM 0.6 0.4 TA = 25°C L = 12μH f = 1MHz 0.2 100 0 TYPICAL 1.2 LOAD CURRENT (A) 140 0 0 INPUT VOLTAGE (V) 25 50 75 100 125 150 TEMPERATURE (°C) 3689 G05 6 12 18 24 VIN (V) 30 3689 G04 Maximum VIN for Full Frequency Maximum VIN for Full Frequency TA = 85°C 30 VIN (V) 25 20 30 TA = 25°C 25 TA = 85°C 20 15 15 10 10 VO = 5V L = 6.8μH f = 2MHz SYNC = 5V 5 0 0.2 0.3 0.4 0.5 LOAD CURRENT (A) 0.1 0.6 0 0 0.7 3689 G07 Switch Current Limit vs Duty Cycle 2.0 MINIMUM TA = 25°C L = 12μH f = 700kHz 0 4 12 16 20 24 VIN (V) 28 32 36 3689 G09 Switch Voltage Drop 600 500 SYNC = HIGH 1.0 400 TA = 25°C 300 TA = –50°C 200 0.5 0.4 8 3689 G08 SYNC = LOW CURRENT LIMIT (A) CURRENT LIMIT (A) 0.4 0.7 1.5 0.8 0 0.6 2.0 TYPICAL 1.2 0.2 0.3 0.4 0.5 LOAD CURRENT (A) MINIMUM 0.6 Switch Current Limit vs Temperature TA = 25°C SYNC = LOW 1.6 0.1 0.8 0.2 VOLTAGE DROP (mV) 0 VO = 3.3V L = 4.7μH f = 2MHz SYNC = 3.3V 5 TYPICAL 1.0 LOAD CURRENT (A) TA = 25°C 35 VIN (V) Maximum Output Current, 3.3VOUT 1.2 35 40 36 3689 G06 TA = 125°C 100 0 20 40 60 DUTY CYCLE (%) 80 100 3689 G10 0 –50 –25 0 0 25 50 75 100 125 150 TEMPERATURE (°C) 3689 G11 0 200 400 600 800 1000 SWITCH CURRENT (mA) 3689 G12 3689fa 5 LT3689/LT3689-5 TYPICAL PERFORMANCE CHARACTERISTICS BST Pin Current Output Voltage Feedback Voltage 0.810 25 5.05 5.04 TA = 125°C TA = 25°C 10 5 5.03 0.805 OUTPUT VOLTAGE (V) TA = –50°C 15 FEEDBACK VOLTAGE (V) BST PIN CURRENT (mA) 20 0.800 0.795 5.02 5.01 5.00 4.99 4.98 4.97 4.96 0 0 400 200 600 800 1000 0.790 –50 –25 0 SWITCH CURRENT (mA) 4.95 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) 0 25 50 75 100 125 150 TEMPERATURE (°C) 3689 G15 3689 G14 3689 G13 Frequency Foldback Switching Frequency Switching Frequency vs RT 50 900 TA = 25°C 1200 RT = 20.5k SWITCHING FREQUENCY (kHz) 850 40 FREQUENCY (kHz) 800 RT (k) 30 20 750 700 650 600 10 1000 550 0 0 0.8 1.2 1.6 FREQUENCY (MHz) 0.4 2 500 –50 –25 2.4 800 600 400 200 0 0 0 25 50 75 100 125 150 TEMPERATURE (°C) 100 200 300 400 500 600 700 800 900 FB VOLTAGE (mV) 3689 G18 3689 G17 3689 G16 Minimum Switch On-Time 140 TA = 25°C RT = 12.7k Overvoltage Lockout VIN Fixed Undervoltage Lockout 40 3.6 ILOAD = 700mA 100 80 60 40 3.5 39 VIN RISING VIN UVLO (V) OVERVOLTAGE LOCKOUT (V) MINIMUM ON-TIME (ns) 120 38 3.4 VIN FALLING 3.3 37 3.2 20 0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 36 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3689 G20 3.1 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3689 G21 3689 G19 3689fa 6 LT3689/LT3689-5 TYPICAL PERFORMANCE CHARACTERISTICS EN/UVLO Pin Threshold 1.300 1.290 TA = –50°C EN/UVLO THRESHOLD (V) EN/UVLO PIN CURRENT (μA) 6 5 TA = 25°C 4 TA = 150°C 3 2 Boost Diode Forward Voltage 900 VIN = 12V 800 BOOST DIODE VOLTAGE (mV) EN/UVLO Pin Current 7 1.280 1.270 1.260 1.250 EN/UVLO THRESHOLD RISING 1.240 1.230 EN/UVLO THRESHOLD FALLING 1.220 1 0 5 10 15 20 VEN/UVLO (V) 25 30 35 700 TA = 25°C 600 TA = 150°C 500 400 300 200 100 1.210 0 TA = –50°C 1.200 –50 –25 3689 G22 0 0 0 25 50 75 100 125 150 TEMPERATURE (°C) 10 30 40 20 BOOST DIODE CURRENT (mA) 50 3689 G24 3689 G23 Switching Waveform: Transition from Burst Mode to Full Frequency Switching Waveform: Burst Mode Operation EN/UVLO Hysteresis Current VOUT 10mV/DIV VOUT 10mV/DIV IL 0.2A/DIV IL 0.2A/DIV VSW 5V/DIV VSW 5V/DIV 4.5 4.0 3.5 3.0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 5μs/DIV VIN = 12V, FRONT PAGE APPLICATION ILOAD = 6mA 3689 G26 1μs/DIV VIN = 12V, FRONT PAGE APPLICATION ILOAD = 60mA 3689 G27 3689 G25 Power-On-Reset Threshold vs Temperature Switching Waveform: Full Frequency Continuous Operation 0.730 VOUT 10mV/DIV POR THRESHOLD (V) EN/UVLO HYSTERESIS CURRENT (μA) 5.0 IL 0.5A/DIV VSW 10V/DIV 0.725 0.720 0.715 1μs/DIV VIN = 12V, FRONT PAGE APPLICATION ILOAD = 600mA 3689 G28 0.710 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3689 G29 3689fa 7 LT3689/LT3689-5 TYPICAL PERFORMANCE CHARACTERISTICS Transient Duration vs POR Comparator Overdrive Watchdog Upper Boundary Period UPPER BOUNDARY PERIOD, t WDU (ms) 21 TRANSIENT DURATION (μs) 700 600 500 400 RESET OCCURS ABOVE THE CURVE 300 200 100 0 0.10 1.00 10.00 100.00 POR COMPARATOR OVERDRIVE VOLTAGE AS PERCENTAGE OF RESET THRESHOLD, VRST (%) CWDT = 1nF MURATA: GRM1882C1H102FA01 20 19 18 17 –50 –25 0 Watchdog Lower Boundary Period 7.0 LOWER BOUNDARY PERIOD, t WDL (ms) 800 25 50 75 100 125 150 TEMPERATURE (°C) CWDT = 10nF MURATA: GRM1885C1H102FA01 6.5 6.0 5.5 5.0 –50 –25 0 3689 G31 25 50 75 100 125 150 TEMPERATURE (°C) 3689 G32 3689 G30 Watchdog Upper Boundary Period vs Capacitance Reset Timeout Period 100000 CPOR = 8.2nF MURATA: GRM2195C1H822FA01 UPPER BOUNDARY PERIOD, tWDU (ms) RESET TIMEOUT PERIOD, t RST (ms) 21 20 19 18 17 –50 –25 0 10000 1000 100 10 1 0.1 0.001 25 50 75 100 125 150 TEMPERATURE (°C) 3689 G33 1000 3689 G34 Watchdog Lower Boundary Period vs Capacitance Reset Timeout Period vs Capacitance 10000 LOWER BOUNDARY PERIOD, tWDL (ms) 10000 RESET TIMEOUT PERIOD, tRST (ms) 0.01 0.1 1 10 100 CWDT PIN CAPICITANCE, CWDT (nF) 1000 100 10 1 0.1 0.01 0.001 0.01 0.1 1 10 100 1000 10000 CPOR PIN CAPICITANCE, CPOR (nF) 3689 G35 1000 100 10 1 0.1 0.01 0.001 0.01 0.1 1 10 100 1000 10000 CWDT PIN CAPICITANCE, CWDT (nF) 3689 G36 3689fa 8 LT3689/LT3689-5 PIN FUNCTIONS BST: The BST pin is used to provide drive voltage higher than the input voltage to the internal NPN power switch. VIN: The VIN pin supplies current to the LT3689’s internal circuitry and to the internal power switch and must be locally bypassed. SW: The SW pin is the output of the internal power switch. Connect this pin to the inductor, catch diode and boost capacitor. DA: Tie the DA pin to the anode of the external catch Schottky diode. If the DA pin current exceeds 1.2A, which could occur in an overload or short-circuit condition, switching is disabled until the DA pin current falls below 1.2A. EN/UVLO: The EN/UVLO pin is used to put the LT3689 in shutdown mode. Pull the pin below 0.3V to shut down the LT3689. The 1.26V threshold can function as an accurate undervoltage lockout (UVLO), preventing the regulator from operating until the input voltage has reached the programmed level. FB: The LT3689 regulates the feedback pin to 0.800V. Connect the feedback resistor divider tap to this pin. For the fixed LT3689-5 output, this pin can be used to connect a phase lead capacitor between the OUT pin and FB pin to optimize transient response. WDE: Watchdog Timer Enable Pin. This pin disables the watchdog timer if the WDE voltage exceeds 1V. WDO is high in this condition. W/T: Setting W/T low puts the LT3689 watchdog timer into window mode. If two or more negative edges occur on WDI before the watchdog lower boundary (tWDL) period expires, or no negative edge occurs within the watchdog upper boundary (tWDU) period, the part will set WDO low. If W/T is set high, the part will only set WDO low if no transition occurs within the watchdog upper boundary period. WDI: Watchdog Timer Input Pin. This pin receives the watchdog signal from a microprocessor. If the appropriate signal is not received, the part will pulse WDO low for a period equal to the reset timeout period. The watchdog timer is disabled until the WDO pin goes high again. RST: Active low, open collector logic output with a weak pull-up to VOUT. After VOUT rises above 90% of its programmed value, the reset remains asserted for the period set by the capacitor on the CPOR pin. WDO: Active low, open collector logic output with weak pull-up to VOUT. WDO pulls low if the WDE is enabled and the microprocessor fails to drive the WDI pin of the LT3689 with an appropriate signal. CWDT: Watchdog Timer Programming Pin. Place a capacitor (CWDT) between this pin and ground to adjust the watchdog upper and lower boundary period. To determine the watchdog upper boundary period, and the lower boundary period, use the following equations: tWDU = 18.2 • CWDT (watchdog upper boundary period) tWDL = 0.588 • CWDT (watchdog lower boundary period) tWDU and tWDL are in ms and CWDT is in nF. As an example, a 47nF capacitor will generate an 855ms watchdog upper boundary period and a 27.6ms watchdog lower boundary period. CPOR: Reset Delay Timer Programming Pin. Attach an external capacitor (CPOR) to GND to set a reset delay time of 2.3ms/nF. RT: Sets the Internal Oscillator Frequency. Tie a 31.6k resistor from RT to GND for a 500kHz switching frequency. SYNC: Drive the SYNC pin with a logic level signal with positive and negative pulse widths of at least 80ns. The RT resistor should be chosen to set the LT3689 switching frequency at least 20% below the lowest synchronization input frequency. OUT: The OUT pin supplies current to the internal circuitry when OUT is above 3V, reducing input quiescent current. The internal Schottky diode is connected from OUT to BST, providing the charging path for the boost capacitor. For the LT3689-5, this pin connects to the internal feedback divider that programs the fixed 5V output. GND: Ground. Tie the exposed pad directly to the ground plane. The exposed pad metal of the package provides both electrical contact to ground and good thermal contact to the printed circuit board. The device must be soldered to the circuit board for proper operation. 3689fa 9 LT3689/LT3689-5 BLOCK DIAGRAM VIN VIN C1 – + INTERNAL 0.8VREF EN/UVLO 3 OUT SLOPE COMP SWITCH LATCH R RT C2 Q OSCILLATOR RT BST S L1 SW SYNC VOUT DISABLE SOFT-START VOUT R1 OUT LT3689-5 ONLY FB R2 ERROR AMP + – 525k D1 Burst Mode OPERATION DETECT C3 DA VC RSEN VC CLAMP GND RC 100k CC WDE 2μA WDI TRANSITION DETECT CWDT WATCHDOG TIMER W/T 22μA + OUT 80mV 1μA FB WDO – + OUT VIN ADJUSTABLE RESET PULSE GENERATOR 1μA – 2μA 3.4V RST + 22μA CPOR 3689 BD 3689fa 10 LT3689/LT3689-5 TIMING DIAGRAMS VOUT VUV tUV tRST RST POWER-ON RESET TIMING WDI WDO tWDU tRST WATCHDOG TIMING (W/T = HIGH), TIMEOUT MODE t < t WDL tRST WDI WDO 3689 TD tRST tWDU WATCHDOG TIMING (W/T = LOW), WINDOW MODE tUV = TIME REQUIRED TO ASSERT RST LOW ONCE VOUT GOES BELOW VUV tRST = PROGRAMMED RESET PERIOD tWDU = WATCHDOG UPPER BOUNDARY PERIOD tWDL = WATCHDOG WINDOW MODE LOWER BOUNDARY PERIOD VUV = OUTPUT VOLTAGE RESET THRESHOLD 3689fa 11 LT3689/LT3689-5 OPERATION The LT3689 is a constant-frequency, current mode stepdown regulator with a watchdog and a reset timer that allows microprocessor supervisory functions. Operation can be best understood by referring to the Block Diagram. Keeping the EN/UVLO pin at ground completely shuts off the part drawing minimal current from the VIN source. To turn on the internal bandgap and the rest of the logic circuitry, raise the EN/UVLO pin above the accurate threshold of 1.26V. Also, VIN needs to be higher than 3.7V for the part to start switching. Switching Regulator Operation An oscillator, with frequency set by RT, enables an RS flipflop, turning on the internal power switch. An amplifier and comparator monitor the current flowing between the VIN and SW pins, turning the switch off when this current reaches a level determined by the voltage at VC. An error amplifier measures the output voltage through the resistor divider tied to the FB pin and servos the VC voltage. If the error amplifier’s output increases, more current is delivered to the output; if it decreases, less current is delivered. An active clamp on the VC voltage provides current limit. An internal regulator provides power to the control circuitry. The bias regulator normally draws current from the VIN pin, but if the OUT pin is connected to an external voltage higher than 3V, bias current will be drawn from the external source (typically the regulated output voltage). This improves efficiency. The OUT pin also provides a current path to the internal boost diode that charges up the boost capacitor. The switch driver operates either from the VIN or from the BST pin. An external capacitor is used to generate a voltage at the BST pin that is higher than the VIN supply. This allows the driver to fully saturate the internal bipolar NPN power switch for efficient operation. To further optimize efficiency, the LT3689 automatically switches to Burst Mode operation in light load situations. Between bursts, all circuitry associated with controlling the output switch is shut down, reducing the input supply current to 85μA in a typical application. The oscillator reduces the LT3689’s operating frequency when the voltage at the FB pin is low. This frequency foldback helps to control the output current during start-up and overload conditions. A comparator monitors the current flowing through the catch diode via the DA pin. This comparator delays switching if the diode current goes higher than 1.2A (typical) during a fault condition such as a shorted output with high input voltage. The switching will only resume once the diode current has fallen below the 1.2A limit. This way the DA comparator regulates the valley current of the inductor to 1.2A during a short-circuit. The LT3689 has an overvoltage protection feature which disables switching when the VIN goes above 38V (typical) during transients. When switching is disabled, the LT3689 can safely sustain transient input voltages up to 60V. Power-On Reset and Watchdog Timer Operation The LT3689 has a power-on reset (POR) comparator that monitors the regulated output voltage. If the output voltage is below 10% of the regulation value, the RST pin is pulled low. Once the output voltage crosses over 90% of the regulation value, a reset timer is started and RST is released after the programmed reset delay time. The reset delay is programmable through the CPOR pin. The watchdog typically monitors a microprocessor’s activity. The watchdog can be enabled or disabled by applying a logic signal to the WDE pin. The watchdog can be operated in either timeout or window mode by applying a logic signal to the W/T pin. In timeout mode, the microprocessor is required to change the logic state of the WDI pin on a periodic basis in order to clear the watchdog timer and to prevent the WDO from going low. In window mode, the watchdog timer requires successive negative edges on the WDI pin to come within a programmed time window to keep WDO from going low. Therefore, in window mode, if the time between the two negative WDI edges is too short or too long, then the WDO pin will be pulled low. When the WDO pin goes low, either in timeout or in window mode, the reset timer turns on and keeps the WDO pin low. The WDO pin will go high again once the reset timer expires or the RST pin goes low when the output voltage falls 10% below the regulation value. Both the timeout and window periods can be set through the CWDT pin. 3689fa 12 LT3689/LT3689-5 APPLICATIONS INFORMATION The output voltage is programmed with a resistor divider between the output and the FB pin. Choose 1% resistors according to: V R1= R2 OUT 1 0.8V For reference designators, refer to the Block Diagram. Setting the Switching Frequency The LT3689 uses a constant-frequency PWM architecture that can be programmed to switch from 350kHz to 2.2MHz by using a resistor tied from the RT pin to ground. Table 1 shows the RT values for various switching frequencies. Table 1. Switching Frequency vs RT SWITCHING FREQUENCY (MHz) RT (kΩ) 0.35 48.7 0.5 31.6 0.6 24.9 0.7 20.5 0.8 16.9 0.9 14.7 1 12.7 1.2 9.53 1.4 7.5 1.6 6.04 1.8 4.87 2 4.02 2.2 3.16 Operating Frequency Tradeoffs Selection of the operating frequency is a tradeoff between efficiency, component size and maximum input voltage. The advantage of high frequency operation is that smaller inductor and capacitor values may be used. The disadvantages are lower efficiency, and narrower input voltage range at constant-frequency. The highest constant-switching frequency (fSW(MAX)) for a given application can be calculated as follows: VOUT + VD f SW(MAX ) = tON(MIN) VIN – VSW + VD ( ) where VIN is the typical input voltage, VOUT is the output voltage, VD is the catch diode drop (~0.5V) and VSW is the internal switch drop (~0.5V at maximum load). If the LT3689 is programmed to operate at a frequency higher than fSW(MAX) for a given VIN input voltage, the LT3689 enters pulse-skipping mode, where it skips switching cycles to maintain regulation. At frequencies higher than fSW(MAX), the LT3689 no longer operates with constantfrequency. The LT3689 enters pulse-skipping mode at frequencies higher than fSW(MAX) because of the limitation on the LT3689’s minimum on-time of 130ns. As the switching frequency is increased above fSW(MAX), the part is required to switch for shorter periods of time to maintain the same duty cycle. Delays associated with turning off the power switch dictate the minimum on-time of the part. When the required on-time decreases below the minimum on-time of 130ns, the switch pulse width remains fixed at 130ns (instead of becoming narrower to accommodate the duty cycle requirement). The inductor current ramps up to a value exceeding the load current and the output ripple increases. The part then remains off until the output voltage dips below the programmed value before it begins switching again. 3689fa 13 LT3689/LT3689-5 APPLICATIONS INFORMATION Maximum Operating Voltage The maximum input voltage for LT3689 applications depends on switching frequency, the absolute maximum ratings of the VIN and BST pins, and by the minimum duty cycle (DCMIN). The LT3689 can operate from input voltages up to 36V, and safely withstand input transient voltages up to 60V. Note that while VIN > 38V (typical), the LT3689 will stop switching, allowing the output to fall out of regulation. DCMIN = tON(MIN) • fSW where tON(MIN) is equal to 130ns (for TJ > 125°C tON(MIN) is equal to 150ns) and fSW is the switching frequency. Running at a lower switching frequency allows a lower minimum duty cycle. The maximum input voltage before pulse-skipping occurs depends on the output voltage and the minimum duty cycle: V +V VIN(PS) = OUT D – VD + VSW DCMIN Example: fSW = 790kHz, VOUT = 3.3V, DCMIN = 130ns • 790kHz = 0.103 VIN(PS) = 3.3V + 0.4V – 0.4V + 0.4V = 36 V 0.103 The LT3689 will regulate the output current at input voltages greater than VIN(PS). For example, an application with an output voltage of 1.8V and switching frequency of 1.5MHz has a VIN(PS) of 11.3V, as shown in Figure 1. Figure 2 shows operation at 24V. Output ripple and peak inductor current have significantly increased. A saturating inductor may further reduce performance. For input voltages over 30V, there are restrictions on the inductor size and saturation rating. See the Inductor Selection section for more details. In pulse-skipping mode, the LT3689 skips switching pulses to maintain output regulation. Above 38V (typical) switching will stop. Transients of up to 60V are acceptable, regardless of switching frequency. Minimum Operating Voltage Range The minimum input voltage is determined either by the LT3689’s minimum operating voltage of ~3.4V or by its maximum duty cycle. The duty cycle is the fraction of time that the internal switch is on and is determined by the input and output voltages: VOUT + VD DC = VIN – VSW + VD Unlike many fixed frequency regulators, the LT3689 can extend its duty cycle by remaining on for multiple cycles. The LT3689 will not switch off at the end of each clock cycle if there is sufficient voltage across the boost capacitor (C3 in the Block Diagram). Eventually, the voltage on the boost capacitor falls and requires refreshing. Circuitry detects VOUT 50mV/DIV (AC) VOUT 50mV/DIV (AC) IL 0.5A/DIV IL 0.5A/DIV 5μs/DIV 3689 F01 Figure 1. Operation Below VIN(PS). VIN = 10V, VOUT = 1.8V and fSW = 1.5MHz 5μs/DIV 3689 F02 Figure 2. Operation Above VIN(PS). VIN = 24V, VOUT = 1.8V and fSW = 1.5MHz. Output Ripple and Peak Inductor Current Increase 3689fa 14 LT3689/LT3689-5 APPLICATIONS INFORMATION this condition and forces the switch to turn off, allowing the inductor current to charge up the boost capacitor. This places a limitation on the maximum duty cycle. The maximum duty cycle that the LT3689 can sustain is 90%. From this DCMAX number, the minimum operating voltage can be calculated using the following equation: V +V VIN(MIN) = OUT D − VD + VSW 0.90 Example: VOUT = 3.3V VIN(MIN) = 3.3V + 0.4V – 0.4V + 0.4V = 4.1V 0.90 Inductor Selection and Maximum Output Current A good first choice for the inductor value is: L = ( VOUT + VF ) • 2 . 2MHz fSW where VF is the voltage drop of the catch diode (~0.4V), fSW is the switching frequency in MHz, and L is in μH. The inductor’s RMS current rating must be greater than the maximum load current and its saturation current should be at least 30% higher. For robust operation in fault conditions (start-up or short-circuit) and high input voltage (>30V), use an 8.2μH or greater inductor (for TJ > 125°C, use 10μH or larger) with a saturation rating of 2.5A, or higher. To keep the efficiency high, the series resistance (DCR) should be less than 0.15Ω and the core material should be intended for high frequency applications. Table 2 lists several vendors and suitable types. The current in the inductor is a triangle wave with an average value equal to the load current. The peak switch current is equal to the output current plus half the peak-topeak inductor ripple current. The LT3689 limits its switch current in order to protect itself and the system from overload faults. Therefore, the maximum output current that the LT3689 will deliver depends on the switch current limit, the inductor value, and the input and output voltages. Also, if the inductor current’s bottom peak exceeds the DA current limit (ILIM(DA)) at high output currents then the DA current comparator will regulate the bottom peak to ILIM(DA). This will result in higher inductor ripple current and will further limit the max output current. The DA current limit consists of a DC and an AC component. The nominal DC component is fixed at 1.2A. The AC component depends on the output voltage, inductor size and a fixed time delay between the DA comparator turning off and switch turning on. Therefore, the DA current limit ILIM(DA) will increase as the output voltage collapses under overload conditions. ILIM(DA) = 1.2A − ( VOUT + VD ) • 0.25µs L Table 2. Inductor Vendors VENDOR URL Sumida www.sumida.com Toko www.toko.com Würth Elektronik www.we-online.com PART SERIES INDUCTANCE RANGE (μH) SIZE (mm) CDRH4D28 CDRH5D28 1.2 to 4.7 2.5 to 10 4.5 × 4.5 5.5 × 5.5 A916CY D585LC 2 to 12 1.1 to 39 6.3 × 6.2 8.1 × 8 WE-TPC(M) WE-PD2(M) 1 to 10 2.2 to 22 4.8 × 4.8 5.2 × 5.8 3689fa 15 LT3689/LT3689-5 APPLICATIONS INFORMATION Choose an inductor using the previous inductor selection equation to guarantee 700mA of output current. If using a smaller inductor, check the DA current limit equation to verify that the DA circuitry will not lower the switching frequency. When the switch is off, the potential across the inductor is the output voltage plus the catch diode drop. This gives the peak-to-peak ripple current in the inductor: ΔIL = (1−DC)(VOUT + VD ) L • fSW where fSW is the switching frequency of the LT3689 and L is the value of the inductor. The peak inductor and switch current is: ΔI ISW(PK) = IL(PK) = IOUT + L 2 To maintain output regulation, this peak current must be less than the LT3689’s switch current limit ILIM. ILIM is at least 1.5A for at low duty cycles and decreases linearly to 0.87A at DC = 85%. The maximum output current is a function of the chosen inductor value. IOUT(MAX) = ILIM − ΔIL 2 ΔIL 2 Choosing an inductor value so that the ripple current is small will allow a maximum output current near the switch current limit. = 1.15A • (1− 0.28 • DC) − One approach to choosing the inductor is to start with the preceding simple rule, determine the available inductors, and choose one to meet cost or space goals. Next, use these equations to check that the LT3689 will be able to deliver the required output current. Note again that these equations assume that the inductor current is continuous. Discontinuous operation occurs when IOUT is less than ΔIL /2. Of course, such a simple design guide will not always result in the optimum inductor for the application. A larger value inductor provides a slightly higher maximum load current and will reduce the output voltage ripple. If the load is lower than 0.7A, decrease the value of the inductor and operate with a higher ripple current. This allows the use of a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. There are graphs in the Typical Performance Characteristics section of this data sheet that show the maximum load current as a function of input voltage for several popular output voltages. Low inductance may result in discontinuous mode operation, which is okay but further reduces maximum load current. For details of maximum output current and discontinuous mode operation, see Linear Technology Application Note 44. Finally, for duty cycles greater than 50% (VOUT / VIN > 0.5), a minimum inductance is required to avoid subharmonic oscillations: L MIN = ( 1.4 VOUT + VD ) fSW where LMIN is in μH, VOUT and VD are in volts, and fSW is in MHz. Input Capacitor Bypass the input of the LT3689 circuit with a ceramic capacitor of an X7R or X5R type. Y5V types have poor performance over temperature and applied voltage, and should not be used. The minimum value of input capacitance depends on the switching frequency. Use an input capacitor of 1μF or more for switching frequencies between 1MHz to 2.2MHz, and 2.2μF or more for frequencies lower than 1MHz. If the input power source has high impedance, or there is significant inductance due to long wires or cables, additional bulk capacitance may be necessary. This can be provided with a lower performance electrolytic capacitor. Step-down regulators draw current from the input supply in pulses with very fast rise and fall times. The input capacitor is required to reduce the resulting voltage ripple at the LT3689 input and to force this very high frequency switching current into a tight local loop, minimizing EMI. A ceramic capacitor is capable of this task, but only if it is placed close to the LT3689 and the catch diode (see the PCB Layout section). A second precaution regarding the ceramic input capacitor concerns the maximum input voltage rating of the LT3689. A ceramic input capacitor combined with trace or cable inductance forms a high quality (under damped) tank circuit. If the 3689fa 16 LT3689/LT3689-5 APPLICATIONS INFORMATION LT3689 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the LT3689’s voltage rating. For a complete discussion, see Linear Technology’s Application Note 88. capacitor must be large to achieve low ESR. Table 3 lists several capacitor vendors. Table 3. Capacitor Vendors VENDOR Output Capacitor and Output Ripple The output capacitor has two essential functions. Along with the inductor, it filters the square wave generated by the LT3689 to produce the DC output. In this role it determines the output ripple, and low impedance at the switching frequency is important. The second function is to store energy in order to satisfy transient loads and stabilize the LT3689’s control loop. Ceramic capacitors have very low equivalent series resistance (ESR) and provide the best ripple performance. A good starting value is: 50 COUT = VOUT fSW where fSW is in MHz, and COUT is the recommended output capacitance in μF. Use X5R or X7R types, which will provide low output ripple and good transient response. Transient performance can be improved with a high value capacitor, but a phase lead capacitor across the feedback resistor R1 may be required to get the full benefit (see the Frequency Compensation section). High performance electrolytic capacitors can be used for the output capacitor. Low ESR is important, so choose one that is intended for use in switching regulators. The ESR should be specified by the supplier and should be 0.1Ω or less. Such a capacitor will be larger than a ceramic capacitor and will have a larger capacitance because the PHONE URL Panasonic (714) 373-7366 www.panasonic.com Kemet (864) 963-6300 www.kemet.com Sanyo (408) 749-9714 www.sanyovideo.com Murata (408) 436-1300 www.murata.com (864) 963-6300 www.taiyo-yuden.com AVX Taiyo Yuden www.avxcorp.com Catch Diode The catch diode conducts current only during switch-off time. Average forward current in normal operation can be calculated from: ID( AVG) = IOUT ( V IN − VOUT ) V IN where IOUT is the output load current. The only reason to consider a diode with a larger current rating than necessary for nominal operation is for the worst-case condition of shorted output. The diode current will then increase to the typical peak switch current limit. Peak reverse voltage is equal to the regulator input voltage. Use a Schottky diode with a reverse voltage rating greater than the input voltage. The overvoltage protection feature in the LT3689 will keep the switch off when VIN > 38V (typical), which allows the use of a 40V rated Schottky even when VIN ranges up to 60V. Table 4 lists several Schottky diodes and their manufacturers. 3689fa 17 LT3689/LT3689-5 APPLICATIONS INFORMATION Table 4. Diode Vendors Frequency Compensation PART NUMBER VR (V) IAVE (A) VF AT IAVE (mV) On Semiconductor MBRM120E MBRM140 20 40 1 1 530 550 Diodes Inc. B120 B130 B140 B0540W B140HB 20 30 40 40 40 1 1 1 0.5 1 500 500 500 510 530 Ceramic Capacitors Ceramic capacitors are small, robust and have very low ESR. However, ceramic capacitors can cause problems when used with the LT3689 due to their piezoelectric nature. When in Burst Mode operation, the LT3689’s switching frequency depends on the load current, and at very light loads the LT3689 can excite the ceramic capacitor at audio frequencies, generating audible noise. Since the LT3689 operates at a lower current limit during Burst Mode operation, the noise is typically very quiet. If this noise is unacceptable, use a high performance tantalum or electrolytic capacitor at the output. LT3689 0.7V The LT3689 uses current mode control to regulate the output, which simplifies loop compensation. In particular, the LT3689 does not require the ESR of the output capacitor for stability, allowing the use of ceramic capacitors to achieve low output ripple and small circuit size. Figure 3 shows an equivalent circuit for the LT3689 control loop. The error amp is a transconductance amplifier with finite output impedance. The power section, consisting of the modulator, power switch and inductor, is modeled as a transconductance amplifier generating an output current proportional to the voltage at the VC node. Note that the output capacitor, C1, integrates this current, and that the capacitor on the VC node (CC) integrates the error amplifier output current, resulting in two poles in the loop. RC provides a zero. With the recommended output capacitor, the loop crossover occurs above the RCCC zero. This simple model works well as long as the value of the inductor is not too high and the loop crossover frequency is much lower than the switching frequency. With a larger ceramic capacitor (very low ESR), crossover may be lower and a phase lead capacitor (CPL) across the feedback divider may improve the phase margin and transient response. Large electrolytic capacitors may have an ESR large enough to create an additional zero, and the phase lead may not be necessary. CURRENT MODE POWER STAGE – gm = OUT +1.2A/V R1 – FB + 800mV CPL gm = 300μA/V VC RC 37k CC 100pF ERROR AMPLIFIER 3M ESR C1 + C1 R2 GND 3689 F03 Figure 3. Model for the Loop Response 3689fa 18 LT3689/LT3689-5 APPLICATIONS INFORMATION Most applications running at VIN greater than 20V will require a small phase lead capacitor, ranging from 2pF to about 30pF, between the FB pin and VOUT for good transient response. The circuits in the Typical Applications section use the appropriate phase lead capacitors and are stable at all input voltages. If the output capacitor is different than the recommended capacitor, stability should be checked across all operating conditions, including load current, input voltage and temperature. The LT1375 data sheet contains a more thorough discussion of loop compensation and describes how to test the stability using a transient load. Figure 4 shows the transient response when the load current is stepped from 360mA to 720mA and back to 360mA. Low Ripple Burst Mode Operation and Pulse-Skipping Mode The LT3689 is capable of operating in either low ripple Burst Mode operation or pulse-skipping mode, which is selected using the SYNC pin. See the Synchronization section for details. To enhance efficiency at light loads, the LT3689 can be operated in low ripple Burst Mode operation that keeps the output capacitor charged to the proper voltage while minimizing the input quiescent current. During Burst Mode operation, the LT3689 delivers single cycle bursts of current to the output capacitor followed by sleep periods where the output power is delivered to the load by the output capacitor. Because the LT3689 delivers power to the output with single, low current pulses, the output ripple is kept below 15mV for a typical application. The LT3689-5 has a slightly higher output ripple of 25mV. This higher ripple can be reduced by using a larger output capacitor. In addition, VIN and OUT quiescent currents are reduced to typically 50μA and 75μA, respectively, during the sleep time. As the load current decreases towards a no-load condition, the percentage of time that the LT3689 operates in sleep mode increases and the average input current is greatly reduced, resulting in high efficiency even at very low loads (see Figure 5). At higher output loads (above approximately 60mA at VIN = 12V for the front page application) the LT3689 will be running at the frequency programmed by the RT resistor, and will be operating in standard PWM mode. The transition between PWM and low ripple Burst Mode operation is seamless, and will not disturb the output voltage. If low quiescent current is not required, the LT3689 can operate in pulse-skipping mode. The benefit of this mode is that the LT3689 will enter full frequency standard PWM operation at a lower output load current than when in Burst Mode operation. The front page application circuit will switch at full frequency at output loads higher than about 15mA at 12VIN. VOUT 10mV/DIV VOUT 50mV/DIV IL 0.2A/DIV IL 250mA/DIV VSW 5V/DIV 10μs/DIV 3689 F04 Figure 4. Transient Load Response of the LT3689 Front Page Application as the Load Current is Stepped from 360mA to 720mA. VOUT = 3.3V, VIN = 12V 5μs/DIV VIN = 12V, FRONT PAGE APPLICATION ILOAD = 8mA 3689 F05 Figure 5. Burst Mode Operation 3689fa 19 LT3689/LT3689-5 APPLICATIONS INFORMATION BST and OUT Pin Considerations Capacitor C3 and the internal boost Schottky diode (see the Block Diagram) are used to generate a boost voltage that is higher than the input voltage. In most cases, a 0.1μF capacitor will work well. Figure 6 shows three ways to arrange the boost circuit. The BST pin must be more than 2.3V above the SW pin for best efficiency. For outputs of 3V and above, the standard circuit (Figure 6a) is best. For outputs between 2.8V and 3V, use a 0.47μF boost capacitor. A 2.5V output presents a special case because it is marginally adequate to support the boosted drive stage while using the internal boost diode. For reliable BST pin operation with 2.5V outputs, use a good external Schottky diode (such as ON Semiconductor’s MBR0540), and a 0.47μF boost capacitor (see Figure 6b). For lower output voltages, the boost diode can be tied to the input (Figure 6c), or to another supply greater than 2.8V. The circuit in Figure 6a is more efficient because the BST pin current and OUT pin quiescent current comes from a lower volt- age source. Ensure that the maximum voltage ratings of the BST and OUT pins are not exceeded. The minimum operating voltage of an LT3689 application is limited by the minimum input voltage (3.7V) and by the maximum duty cycle, as outlined in the Minimum Operating Voltage Range section. For proper start-up, the minimum input voltage is also limited by the boost circuit. If the input voltage is ramped slowly, or the LT3689 is turned on with its EN/UVLO pin when the output is already in regulation, then the boost capacitor may not be fully charged. Because the boost capacitor is charged with the energy stored in the inductor, the circuit will rely on some minimum load current to get the boost circuit running properly. This minimum load will depend on input and output voltages, and on the arrangement of the boost circuit. The minimum load generally goes to zero once the circuit has started. For lower start-up voltage, the boost diode can be tied to VIN ; however, this restricts the input range to one-half of the absolute maximum rating of the BST pin. VOUT VOUT BST BST VIN VIN D2 OUT OUT LT3689 VIN C3 VIN LT3689 C3 SW 2.2μF GND GND 2.2μF (6a) For VOUT > 2.8V SW (6b) For 2.5V < VOUT < 2.8V VOUT OUT BST VIN 2.2μF VIN LT3689 GND C3 SW 3689 F06 (6c) For VOUT < 2.5V; VIN(MAX) = 30V Figure 6. Three Circuits for Generating the Boost Voltage 3689fa 20 LT3689/LT3689-5 APPLICATIONS INFORMATION Another way to lower the start-up voltage is by using a resistor divider on the EN/UVLO pin (see the Shutdown and Undervoltage Lockout section). A resistor divider on EN/UVLO pin programs the turn-on threshold to slightly higher than the minimum VIN voltage required to run at full load. Below the EN/UVLO high voltage, the part will stay shut off and the output cap will remain discharged during the worse case slow VIN ramp. When the EN/UVLO pin crosses the EN/UVLO high threshold, the part will turn on and the empty output capacitor will provide enough load to bring the output voltage in regulation. This technique significantly lowers the start-up voltage of the circuit. The plot in Figure 7 depicts the minimum load required to start and run (as a function of input voltage). It also depicts the benefit of programming the EN/UVLO threshold to lower the start-up voltage at low load currents. At light loads, the inductor current becomes discontinuous and the effective duty cycle can be very high. This reduces the minimum input voltage to approximately 300mV above VOUT. At higher load currents, the inductor current is continuous and the duty cycle is limited by the maximum duty cycle of the LT3689, requiring a higher input voltage to maintain regulation. Soft-Start The LT3689 has an internal soft-start that gradually ramps up the switch current limit from about 100mA to the switch’s maximum current limit in typical value of 150μs, as shown in Figure 8. This feature limits the inrush current during start-up and prevents the switch current from spiking when the EN/UVLO pin crosses the UVLO threshold. A soft-start sequence is also initiated right after a VIN overvoltage/undervoltage lockout, or thermal shutdown fault in order to prevent the switch current from suddenly jumping to its maximum current limit. 8.0 6.0 TO START: EN/UVLO TIED TO VIN 7.5 7.0 TO START: EN/UVLO HIGH THRESHOLD = 4.85V 5.0 6.5 VIN (V) VIN (V) TO START: EN/UVLO TIED TO VIN 5.5 TO START: EN/UVLO HIGH THRESHOLD = 6.15V 4.5 6.0 4.0 5.5 3.5 TO RUN 5.0 1 100 LOAD (mA) VOUT = 5V L = 8.2μH TO RUN 3.0 10 1000 1 10 100 LOAD (mA) 3589 F07a fSW = 800KHz TA = 25°C 1000 3589 F07b VOUT = 3.3V fSW = 800KHz L = 8.2μH TA = 25°C Figure 7. LT3689 Minimum VIN to Start and Run vs Load VOUT 2V/DIV IL 0.5A/DIV IVIN 0.2A/DIV 20μs/DIV VIN = 12V VOUT = 5V 3689 F08 f = 2MHz CIN = 1μF CERAMIC + 100μF ELECTROLYTIC Figure 8. Internal Soft-Start 3689fa 21 LT3689/LT3689-5 APPLICATIONS INFORMATION Synchronization To select low ripple Burst Mode operation, tie the SYNC pin below 0.3V (this can be ground or a logic output). Synchronizing the LT3689 oscillator to an external frequency can be done by connecting a square wave (with positive and negative pulse width >80ns) to the SYNC pin. The square wave amplitude should have valleys that are below 0.3V and peaks that are above 1V (up to 6V). The LT3689 will not enter Burst Mode operation at low output loads while synchronized to an external clock, but instead will skip pulses to maintain regulation. The LT3689 may be synchronized over a 350kHz to 2.5MHz range. The RT resistor should be chosen to set the LT3689 switching frequency 20% below the lowest synchronization input. For example, if the synchronization signal will be 350kHz and higher, the RT should be chosen for 280kHz. To assure reliable and safe operation, the LT3689 will only synchronize when the output voltage is above 90% of its regulated voltage. It is therefore necessary to choose a large enough inductor value to supply the required output current at the frequency set by the RT resistor (see the Inductor Selection section). It is also important to note that the slope compensation is set by the RT value. When the sync frequency is much higher than the one set by RT, the slope compensation will be significantly reduced, which may require a larger inductor value to prevent subharmonic oscillation. The minimum inductor value LT3689 VIN 1.25V should be calculated using the RT programmed frequency to avoid subharmonic oscillation. Shutdown and Undervoltage Lockout Figure 9 shows how to add undervoltage lockout (UVLO) to the LT3689. Typically, UVLO is used in situations where the input supply is current limited, or has a relatively high source resistance. A switching regulator draws constant power from the source, so source current increases as source voltage drops. This looks like a negative resistance load to the source and can cause the source to current limit or latch low under low source voltage conditions. UVLO prevents the regulator from operating at source voltages where the problems might occur. An internal comparator will force the part into shutdown below the minimum VIN of 3.4V. This feature can be used to prevent excessive discharge of battery-operated systems. If an adjustable UVLO threshold is required, the EN/UVLO pin can be used. The threshold voltage of the EN/UVLO pin comparator is 1.26V. Current hysteresis is added above the EN threshold. This can be used to set voltage hysteresis of the UVLO using the following: V H VL R3 = 4k 4µA R4 = VH – 1.26V 1.26V R3 4µA VC R3 EN/UVLO C1 + R4 SS 4μA 3689 F09 Figure 9. Undervoltage Lockout 3689fa 22 LT3689/LT3689-5 APPLICATIONS INFORMATION Example: switching should not start until the input is above 4.40V, and is to stop if the input falls below 4V. V H = 4.40V,V L = 4V R3 = R4 = 4.40V − 4V − 4k = 95.3k 4µA 1.26V = 43.2k 4.40V −1.26V – 4µA (Nearest 1% Resistor) 95.3k Keep the connection from the resistor to the EN/UVLO pin short and make sure the interplane or surface capacitance to switching nodes is minimized. If high resistor values are used, the EN/UVLO pin should be bypassed with a 1nF capacitor to prevent coupling problems from the switch node. Output Voltage Monitoring The LT3689 provides power supply monitoring for microprocessor-based systems. The features include power-on reset (POR) and watchdog timing. A precise internal voltage reference and glitch immune precision POR comparator circuit monitor the LT3689 output voltage. The switcher’s output voltage must be above 90% of programmed value for RST not to be asserted (refer to the Timing Diagram). The LT3689 will assert RST during power-up, power-down and brownout conditions. Once the output voltage rises above the RST threshold, the adjustable reset timer is started and RST is released after the reset timeout period. On power-down, once the output voltage drops below RST threshold, RST is held at a logic low. The reset timer is adjustable using external capacitors. The RST pin has a weak pull-up to the OUT pin. The POR comparator is designed to be robust against FB pin noise, which could potentially false trigger the RST pin. The POR comparator lowpass filters the first stage of the comparator. This filter integrates the output of the comparator before asserting the RST. The benefit of adding this filter is that any transients at the buck regulator’s output must be of sufficient magnitude and duration before it triggers a logic change in the output (see the Typical Transient vs POR Comparator Overdrive in the Typical Performance Characteristics section). This prevents spurious resets caused by output voltage transients such as load steps or short brownout conditions without sacrificing the DC reset threshold accuracy. Watchdog The LT3689 includes an adjustable watchdog timer that monitors a μP’s activity. If a code execution error occurs in a μP, the watchdog will detect this error and will set the WDO low. This signal can be used to interrupt a routine or to reset a microprocessor. The watchdog is operated either in timeout or window mode. In timeout mode, the microprocessor needs to toggle the WDI pin before the watchdog timer expires, to keep the WDO pin high. If no WDI pulse (either positive or negative) appears during the programmed timeout period, then the circuitry will pull WDO low. During normal operation, the WDI input signal’s high to low, and low to high transition periods should be set lower than the watchdog’s programmed time to keep WDO inactive. In window mode, the watchdog circuitry is triggered by negative edges on the WDI pin. The window mode restricts the WDI pin’s negative going pulses to appear inside a programmed time window (see the Timing Diagram) to prevent WDO from going low. If more than two pulses are registered in the watchdog lower boundary period, the WDO is forced to go low. The WDI edges are ignored while the CWDT capacitor charges from 0V to 200mV right after a low to high transition on the WDO or RST pin. The WDO also goes low if no negative edge is supplied to the WDI pin in the watchdog upper boundary period. During a code execution error, the microprocessor will output WDI pulses that would be either too fast or too slow. This condition will assert WDO and force the microprocessor to reset the program. In window mode, the WDI signal frequency is bounded by an upper and lower limit for normal operation. The WDI input frequency period should be higher than the tWDL period, and lower than the tWDU period, to keep WDO high under normal conditions. The window mode’s tWDL and tWDU times have a fixed ratio of 31 between them. These times can be increased or decreased by adjusting an external capacitor on the CWDT pin. 3689fa 23 LT3689/LT3689-5 APPLICATIONS INFORMATION In both watchdog modes, when WDO is asserted, the reset timer is enabled. Any WDI pulses that appear while the reset timer is running are ignored. When the reset timer expires, the WDO is allowed to go high again. Therefore, if no input is applied to the WDI pin, then the watchdog circuitry produces a train of pulses on the WDO pin. The high time of this pulse train is equal to the timeout period, and low time is equal to the reset period. Also, WDO and RST cannot be logic low simultaneously. If WDO is low and RST goes low, then WDO will go high. The WDE pin allows the user to turn on and off the watchdog function. Do not leave this pin open. Tie it high or low to turn watchdog off or on, respectively. The W/T pin enables/disables the window/timeout mode. Leaving this pin open is fine and will put the watchdog in window mode. It has a weak pull-down to ground. The WDI pin has an internal 2μA weak pull-up that keeps the WDI pin high. If watchdog is disabled, leaving this pin open is acceptable. Selecting the Reset Timing Capacitors The reset timeout period is adjustable in order to accommodate a variety of microprocessor applications. The reset timeout period, (tRST), is adjusted by connecting a capacitor, CPOR , between the CPOR pin and ground. The value of this capacitor is determined by: pF CPOR = t RST • 432 ms This equation is accurate for reset timeout periods of 5ms, or greater. To program faster timeout periods, see the Reset Timeout Period vs Capacitance graph in the Typical Performance Characteristics section. Leaving the CPOR pin unconnected will generate a minimum reset CWDT = 10nF, tWDL = 5.8ms WDI 5V/DIV VOUT 2V/DIV WDO 2V/DIV RST 2V/DIV CWDT 1V/DIV tRST = 165ms CPOR = 71nF CPOR 1V/DIV 50ms/DIV CPOR 1V/DIV 3689 F10 5ms/DIV Figure 10. Reset Timer Waveforms 3689 F11 Figure 11. Window Watchdog Waveforms (W/T = Low) tRST = 165ms, CPOR = 71nF WDI 5V/DIV WDO 2V/DIV tWDU = 180ms, CWDT = 10nF CWDT 1V/DIV CPOR 1V/DIV 100ms/DIV 3689 F12 Figure 12. Timeout Watchdog Waveforms (W/T = High) 3689fa 24 LT3689/LT3689-5 APPLICATIONS INFORMATION timeout of approximately 25μs. Maximum reset timeout is limited by the largest available low leakage capacitor. The accuracy of the timeout period will be affected by capacitor leakage (the nominal charging current is 2μA) and capacitor tolerance. A low leakage ceramic capacitor is recommended. Selecting the Watchdog Timing Capacitor The watchdog timeout period is adjustable and can be optimized for software execution. The watchdog upper boundary timeout period, tWDU is adjusted by connecting a capacitor, CWDT, between the CWDT pin and ground. Given a specified watchdog timeout period, the capacitor is determined by: pF C WDT = t WDU • 55 ms This equation is accurate for upper boundary periods of 20ms, or greater. The watchdog lower boundary period (tWDL) has a fixed relationship to tWDU for a given capacitor. The tWDL period is related to tWDU by the following: t WDL 1 = •t 31 WDU In addition, the following equation can be used to calculate the watchdog lower boundary period for a given CWDT capacitor value. C WDT = t WDL 1 . 7nF • ms Shorted and Reversed Input Protection If an inductor is chosen to prevent excessive saturation, the LT3689 will tolerate a shorted output. When operating in short-circuit condition, the LT3689 will reduce its frequency until the valley current is at a typical value of 1.2A (see Figure 13). There is another situation to consider in systems where the output will be held high when the input to the LT3689 is absent. This may occur in battery charging applications or in battery backup systems where a battery or some other supply is diode ORed with VSW 20V/DIV IL 0.5A/DIV 10μs/DIV Figure 13. The LT3689 Reduces its Frequency to Below 100kHz to Protect Against Shorted Output with 36V Input OUT VIN BST VIN LT3689 Leaving the CWDT pin unconnected will generate a minimum watchdog timeout of approximately 200μs. Maximum timeout is limited by the largest available low leakage capacitor. The accuracy of the timeout period will be affected by capacitor leakage (the nominal charging current is 2μA) and capacitor tolerance. A low leakage ceramic capacitor is recommended. VOUT SW DA These lower boundary period equations are accurate for a tWDL of 3ms, or greater. To program faster tWDU and tWDL periods, see the Watchdog Upper and Lower Boundary Periods vs Capacitance graphs in the Typical Performance Characteristics section. 3689 F13 EN/UVLO GND FB + 3689 F14 Figure 14. Diode D4 Prevents a Shorted Input from Discharging a Backup Battery Tied to the Output; It Also Protects the Circuit from a Reversed Input. The LT3689 Runs Only When the Input is Present 3689fa 25 LT3689/LT3689-5 APPLICATIONS INFORMATION the LT3689’s output. If the VIN pin is allowed to float and the EN/UVLO pin is held high (either by a logic signal or because it is tied to VIN), then the LT3689’s internal circuitry will pull its quiescent current through its SW pin. This is fine if the system can tolerate a few mA in this state. If the EN/UVLO pin is grounded, the SW pin current will drop to essentially zero. However, if the VIN pin is grounded while the output is held high, then parasitic diodes inside the LT3689 can pull large currents from the output through the SW pin and the VIN pin. Figure 14 shows a circuit that will run only when the input voltage is present and that protects against a shorted or reversed input. PCB Layout For proper operation and minimum EMI, care must be taken during printed circuit board layout. Figure 15 shows the recommended component placement with trace, ground plane and via locations. Note that large, switched currents flow in the LT3689’s VIN and SW pins, the catch diode (D1) and the input capacitor (C1). The loop formed by these components should be as small as possible. These components, along with the inductor and output capacitor, should be placed on the same side of the circuit board. Place a local, unbroken ground plane below these components. The SW and BST nodes should be as small Figure 15. Example Layout for QFN Package. A Good PCB Layout Ensures Proper Low EMI Operation 3689fa 26 LT3689/LT3689-5 APPLICATIONS INFORMATION as possible. Finally, keep the FB node small so that the ground traces will shield them from the SW and BOOST nodes. The Exposed Pad on the bottom of the package must be soldered to ground so that the pad acts as a heat sink. To keep thermal resistance low, extend the ground plane as much as possible, and add thermal vias under and near the LT3689 to additional ground planes within the circuit board and on the bottom side. be derated as the ambient temperature approaches 125°C (150°C for H-grade). A board measuring 5cm × 7.5cm with a top layer layout similar to Figure 15 was evaluated in still air at 3.3VOUT, 700kHz switching frequency. At 700mA load, the temperature reached approximately 12°C above ambient for input voltages equal to 12V and 24V. Power dissipation within the LT3689 can be estimated by calculating the total power loss from an efficiency measurement and subtracting the catch diode loss. The die temperature is calculated by multiplying the LT3689 power dissipation by the thermal resistance from junction-to-ambient. High Temperature Considerations The PCB must provide heat sinking to keep the LT3689 cool. The Exposed Pad on the bottom of the package must be soldered to a ground plane. This ground should be tied to large copper layers below with thermal vias; these layers will spread the heat dissipated by the LT3689. Placing additional vias can reduce thermal resistance further. Because of the large output current capability of the LT3689, it is possible to dissipate enough heat to raise the junction temperature beyond the absolute maximum of 125°C (150°C for H-grade). When operating at high ambient temperatures, the maximum load current should Other Linear Technology Publications Application Notes 19, 35 and 44 contain more detailed descriptions and design information for buck regulators and other switching regulators. The LT1376 data sheet has a more extensive discussion of output ripple, loop compensation and stability testing. Design Note 318 shows how to generate a bipolar output supply using a buck regulator. TYPICAL APPLICATIONS 5V Step-Down Converter VIN 6.3V TO 36V TRANSIENT TO 60V C1 1μF WINDOW TIMEOUT WATCHDOG_DEFEAT μP EN/UVLO OUT BST VIN W/T C2 0.1μF WDE I/O WDI I/O WDO LT3689 SW C4 5.6pF D1 RST RESET CPOR C5 68nF tRST = 157ms R1 536k DA FB RT SYNC CWDT C6 10nF tWDU = 182ms L1 12μH R2 102k GND fSW = 1MHz 5V 700mA C3 10μF RT 12.7k 3689 TA02 L1: CDR125NP-12MC D1: MBRM140 C1, C2, C3: X7R or X5R 3689fa 27 LT3689/LT3689-5 TYPICAL APPLICATIONS 3.3V Step-Down Converter VIN 4.5V TO 36V TRANSIENT TO 60V C1 2.2μF WINDOW TIMEOUT WATCHDOG_DEFEAT μP EN/UVLO OUT BST VIN W/T C2 0.1μF WDE I/O WDI I/O WDO LT3689 SW C4 10pF D1 RST RESET R1 316k DA FB RT SYNC CWDT C6 10nF tWDU = 182ms L1 12μH CPOR R2 100k GND C5 68nF tRST = 157ms 3.3V 700mA C3 22μF RT 20.5k fSW = 700kHz 3689 TA03 L1: CDR125NP-12MC D1: MBRM140 C1, C2, C3: X7R or X5R 5V, 2MHz Step-Down Converter VIN 6.3V TO 18V TRANSIENT TO 60V C1 1μF WINDOW TIMEOUT WATCHDOG_DEFEAT μP VIN W/T EN/UVLO OUT BST C2 0.1μF WDE I/O WDI I/O WDO LT3689-5 SW D1 RST RESET C6 10nF tWDU = 182ms CPOR C5 68nF tRST = 157ms C4 2.7pF DA FB RT SYNC CWDT L1 10μH 5V 700mA C3 4.7μF GND fSW = 2MHz RT 4.02k 3689 TA04 C1, C2, C3: X7R OR X5R D1: MBRM140 3689fa 28 LT3689/LT3689-5 PACKAGE DESCRIPTION MSE Package 16-Lead Plastic MSOP, Exposed Die Pad (Reference LTC DWG # 05-08-1667 Rev A) BOTTOM VIEW OF EXPOSED PAD OPTION 2.845 p 0.102 (.112 p .004) 5.23 (.206) MIN 2.845 p 0.102 (.112 p .004) 0.889 p 0.127 (.035 p .005) 8 1 1.651 p 0.102 (.065 p .004) 1.651 p 0.102 3.20 – 3.45 (.065 p .004) (.126 – .136) 0.305 p 0.038 (.0120 p .0015) TYP 16 0.50 (.0197) BSC 4.039 p 0.102 (.159 p .004) (NOTE 3) RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 0.35 REF 0.12 REF DETAIL “B” CORNER TAIL IS PART OF DETAIL “B” THE LEADFRAME FEATURE. FOR REFERENCE ONLY 9 NO MEASUREMENT PURPOSE 0.280 p 0.076 (.011 p .003) REF 16151413121110 9 DETAIL “A” 0o – 6o TYP 3.00 p 0.102 (.118 p .004) (NOTE 4) 4.90 p 0.152 (.193 p .006) GAUGE PLANE 0.53 p 0.152 (.021 p .006) 1234567 8 DETAIL “A” 1.10 (.043) MAX 0.18 (.007) SEATING PLANE 0.17 – 0.27 (.007 – .011) TYP 0.50 (.0197) BSC NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.86 (.034) REF 0.1016 p 0.0508 (.004 p .002) MSOP (MSE16) 0608 REV A 3689fa 29 LT3689/LT3689-5 PACKAGE DESCRIPTION UD Package 16-Lead Plastic QFN (3mm × 3mm) (Reference LTC DWG # 05-08-1691) 0.70 p0.05 3.50 p 0.05 1.45 p 0.05 2.10 p 0.05 (4 SIDES) PACKAGE OUTLINE 0.25 p0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 3.00 p 0.10 (4 SIDES) BOTTOM VIEW—EXPOSED PAD PIN 1 NOTCH R = 0.20 TYP OR 0.25 s 45o CHAMFER R = 0.115 TYP 0.75 p 0.05 15 PIN 1 TOP MARK (NOTE 6) 16 0.40 p 0.10 1 1.45 p 0.10 (4-SIDES) 2 (UD16) QFN 0904 0.200 REF 0.00 – 0.05 NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WEED-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 0.25 p 0.05 0.50 BSC 3689fa 30 LT3689/LT3689-5 REVISION HISTORY REV DATE DESCRIPTION PAGE NUMBER A 04/10 Added LT3689-5 Fixed Output Voltage Option 1–32 3689fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 31 LT3689/LT3689-5 TYPICAL APPLICATION 1.8V Step-Down Converter with System Reset Generated by Watchdog Timing or Output Voltage Failure VIN 3.6V TO 16V TRANSIENT TO 27V C1 1μF WINDOW TIMEOUT WATCHDOG_DEFEAT μP I/O VIN EN/UVLO OUT BST W/T WDI L1 4.7μH C2 0.1μF WDE LT3689 SW L1: WE-PD2: 7447745047 D1: MBRM140 C1, C2, C3: X7R OR X5R C6 10nF tWDU = 182ms D1 RST RESET C5 68nF tRST = 157ms 1.8V 700mA C4 15pF WDO DA FB RT SYNC CWDT CPOR GND fSW = 900kHz R1 127k RT 14.7k R2 102k C3 47μF 3689 TA05 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1766 60V, 1.2A (IOUT), 200kHz, High Efficiency Step-Down DC/DC Converter VIN: 5.5V to 60V, VOUT(MIN) = 1.20V, IQ = 2.5mA, ISD = 25μA, TSSOP-16 and TSSOP-16E Packages LT1936 36V, 1.4A (IOUT), 500kHz High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 36V, VOUT(MIN) = 1.2V, IQ = 1.9mA, ISD <1μA, MS8E Package LT1976/LT1977 60V, 1.2A (IOUT), 200kHz/500kHz, High Efficiency Step-Down VIN: 3.3V to 60V, VOUT(MIN) = 1.20V, IQ = 100μA, ISD <1μA, TSSOP-16E DC/DC Converter with Burst Mode Operation Package LT3434/LT3435 60V, 2.4A (IOUT), 200kHz/500kHz, High Efficiency Step-Down VIN: 3.3V to 60V, VOUT(MIN) = 1.20V, IQ = 100mA, ISD <1μA, TSSOP-16E DC/DC Converter with Burst Mode Operation Package LT3437 60V, 400mA (IOUT), Micropower Step-Down DC/DC Converter with Burst Mode Operation VIN: 3.3V to 60V, VOUT(MIN) = 1.25V, IQ = 100μA, ISD <1μA, 3mm × 3mm DFN-10 and TSSOP-16E Packages LT3480 36V with Transient Protection to 60V, 2A (IOUT), 2.4MHz, High Efficiency Step-Down DC/DC Converter with Burst Mode Operation VIN: 3.6V to 38V, VOUT(MIN) = 0.78V, IQ = 70μA, ISD <1μA, 3mm × 3mm DFN-10 and MSOP-10E Packages LT3481 34V with Transient Protection to 36V, 2A (IOUT), 2.8MHz, High Efficiency Step-Down DC/DC Converter with Burst Mode Operation VIN: 3.6V to 34V, VOUT(MIN) = 1.26V, IQ = 50mA, ISD <1μA, 3mm × 3mm DFN-10 and MSOP-10E Packages LT3493 36V, 1.4A (IOUT), 750kHz High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 36V, VOUT(MIN) = 0.8V, IQ = 1.9mA, ISD <1μA, 2mm × 3mm DFN-6 Package LT3500 36V, 40VMAX, 2A, 2.5MHz High Efficiency Step-Down DC/DC Converter and LDO Controller VIN: 3.6V to 36V, VOUT(MIN) = 0.8V, IQ = 2.5mA, ISD <10μA, 3mm × 3mm DFN-10 Package LT3505 36V with Transient Protection to 40V, 1.4A (IOUT), 3MHz, High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 34V, VOUT(MIN) = 0.78V, IQ = 2mA, ISD = 2μA, 3mm × 3mm DFN-8 and MSOP-8E Packages LT3507 36V 2.5MHz, Triple (2.4A + 1.5A + 1.5A (IOUT)) with LDO Controller High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 36V, VOUT(MIN) = 0.8V, IQ = 2.5mA, ISD = 10μA, TSSOP-16 and TSSOP-16E Packages LT3508 36V with Transient Protection to 40V, Dual 1.4A (IOUT), 3MHz, High Efficiency Step-Down DC/DC Converter VIN: 3.7V to 37V, VOUT(MIN) = 0.8V, IQ = 4.6mA, ISD = 1μA, 4mm × 4mm QFN-24 and TSSOP-16E Packages LT3682 36V, 60VMAX, 1A, 2.2MHz High Efficiency Micropower Step- VIN: 3.6V to 36V, VOUT(MIN) = 0.8V, IQ = 75mA, ISD <1μA, 3mm × 3mm Down DC/DC Converter DFN-12 Package LT3684 34V with Transient Protection to 36V, 2A (IOUT), 2.8MHz, High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 34V, VOUT(MIN) = 1.26V, IQ = 850μA, ISD <1μA, 3mm × 3mm DFN-10 and MSOP-10E Packages LT3685 36V with Transient Protection to 60V, 2A (IOUT), 2.4MHz, High Efficiency Step-Down DC/DC Converter VIN: 3.6V to 38V, VOUT(MIN) = 0.78V, IQ = 70μA, ISD <1μA, 3mm × 3mm DFN-10 and MSOP-10E Packages 3689fa 32 Linear Technology Corporation LT 0410 REV A • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2010