LTC4241 PCI-Bus with 3.3V Auxiliary Hot Swap Controller U FEATURES ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTIO The LTC®4241 is a Hot Swap controller that allows a board to be safely inserted and removed from a live PCI-bus slot. It has a primary controller that controls the four PCI supplies and an independent auxiliary controller to control the 3.3V auxiliary supply. External N-channel transistors are used to control the 3.3V, 5V and 3.3V auxiliary supplies while on-chip switches control the –12V and 12V supplies. The 3.3V, 5V and 3.3V auxiliary supplies can be ramped up at an adjustable rate. Electronic circuit breakers protect all five supplies against overcurrent faults. The foldback current limit feature reduces current spikes and power dissipation when shorts occur. The PWRGD output of the primary controller indicates when all four PCI supplies are within tolerance. The FAULT output indicates an overcurrent condition for any of the five supplies. Allows Safe Board Insertion and Removal from a Live PCI Slot Controls 3.3V, 5V, –12V, 12V and 3.3V Auxiliary Supplies Independent 3.3V Auxiliary Supply Hot SwapTM Controller Adjustable Foldback Current Limit with Circuit Breaker Adjustable Supply Voltage Power-Up Rate High Side Drive for External N-Channel FETs –12V and 12V On-Chip Switches Fault and Power Good Outputs U APPLICATIO S ■ ■ PCI-Based Servers Computer Systems The LTC4241 is available in the 20-pin narrow SSOP package. , LTC and LT are registered trademarks of Linear Technology Corporation. Hot Swap is a trademark of Linear Technology Corporation. U TYPICAL APPLICATIO GND R1 0.007Ω R2 0.005Ω R3 0.07Ω SYSTEM POWER SUPPLY 11 8 1 2 12 5 R8 10k PCI POWER SYSTEM CONTROLLER 6 R9 10k 7 10 5V 5A R4 10Ω Q2 IRF7413 R5 10Ω Q3 Si2306DS C3 10nF Q1 IRF7413 3.3VAUX 500mA R7 100Ω C1 0.047µF R6 10Ω 9 13 14 15 AUXIN AUXSENSE AUXGATE 3VIN 3VSENSE GATE 3.3V 7.6A 3 3VOUT 17 16 18 5VIN 5VSENSE 5VOUT GND 12VIN VEEIN 12VOUT AUXON ON FAULT LTC4241 VEEOUT TIMER PWRGD 20 12V 500mA 19 –12V 100mA 4 BACKPLANE CONNECTOR C2 0.1µF LOGIC RESET RESET 4241 F01 Figure 1. Hot Swappable PCI and 3.3V Auxiliary Supplies sn4241 4241f 1 LTC4241 U W W W ABSOLUTE AXI U RATI GS U W U PACKAGE/ORDER I FOR ATIO (Note 1) Supply Voltages 12VIN ................................................................... 14V VEEIN .................................................................. –14V AUXIN ................................................................... 7V Input Voltage ON ......................................................... –0.3V to 14V AUXON .................................................. –0.3V to 14V Output Voltages (FAULT, PWRGD) .................................. –0.3V to 14V Analog Voltages TIMER, 3VIN, 3VSENSE, GATE, 5VSENSE, 5VIN ............................. –0.3V to (12VIN + 0.3V) 3VOUT, 5VOUT ........................................ –0.3V to 14V AUXSENSE .......................... –0.3V to (AUXIN + 0.3V) VEEOUT ................................................ –14V to + 0.3V 12VOUT .................................................. –0.3V to 14V AUXGATE ......................... Internally Limited (Note 3) Operating Temperature Range LTC4241CGN ........................................... 0°C to 70°C LTC4241IGN ........................................–40°C to 85°C Storage Temperature Range ..................–65°C to 150°C Lead Temperature (Soldering,10sec).................... 300°C ORDER PART NUMBER LTC4241CGN LTC4241IGN TOP VIEW 12VIN 1 20 12VOUT VEEIN 2 19 VEEOUT 3VOUT 3 18 5VOUT TIMER 4 17 5VIN ON 5 16 5VSENSE FAULT 6 15 GATE PWRGD 7 14 3VSENSE GND 8 13 3VIN AUXGATE 9 12 AUXON AUXSENSE 10 11 AUXIN GN PACKAGE 20-LEAD NARROW PLASTIC SSOP TJMAX = 150°C, θJA = 135°C/W Consult LTC Marketing for parts specified with wider operating temperature ranges. DC ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V12VIN = 12V, VVEEIN = –12V, V3VIN = 3.3V, V5VIN = 5V, VAUXIN = 3.3V. (Note 2) SYMBOL PARAMETER CONDITIONS MIN IDD V12VIN Supply Current VAUXIN Supply Current ON = V12VIN AUXON = VAUXIN ● ● VLKO Undervoltage Lockout, Low-to-High Transition 12VIN 3VIN 5VIN AUXIN ● ● ● ● VLKH Undervoltage Lockout Hysteresis 3VIN, 5VIN AUXIN VSENSE5(TH) Current Limit Sense Voltage Threshold (V5VIN – V5VSENSE) V5VOUT = 0V V5VOUT > 4V ● ● 5.5 40 9 55 14.5 70 mV mV VSENSE3(TH) Current Limit Sense Voltage Threshold (V3VIN – V3VSENSE) V3VOUT = 0V V3VOUT > 2V ● ● 5.5 40 9 55 14.5 70 mV mV tCB Circuit Breaker Trip Filter Time (V5VIN – V5VSENSE) = Step 0 to 100mV (VAUXIN – VAUXSENSE) = Step 0 to 100mV IGATE GATE Pin Output Current ON High, FAULT High, VGATE = GND ON Low, FAULT High, VGATE = 5V ON High, FAULT Low, VGATE = 5V 6.5 2.25 3.65 2.35 TYP MAX UNITS 2.5 0.5 8 1.5 mA mA 9 2.50 3.90 2.60 10.8 2.75 4.15 2.85 V V V V 20 120 mV mV µs µs 17 8 ● –20 5 –60 200 25 –100 35 µA µA mA sn4241 4241f 2 LTC4241 DC ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V12VIN = 12V, VVEEIN = –12V, V3VIN = 3.3V, V5VIN = 5V, VAUXIN = 3.3V. (Note 2) SYMBOL PARAMETER CONDITIONS ∆VGATE External Gate Voltage (V12VIN – VGATE) VDROP Internal Switch Voltage Drop ICL(12) MIN TYP MAX UNITS ● 100 200 mV (V12VIN – V12VOUT), I12VOUT = 500mA (VEEOUT – VVEEIN), IVEEIN = 100mA ● ● 200 120 600 250 mV mV Current Limit 12VIN = 12V, 12VOUT = 0V, TIMER = GND 12VIN = 12V, 12VOUT = 11V, TIMER = GND ● ● –50 –525 –300 –850 –575 –1500 mA mA ICL(VEE) Current Limit VEEIN = –12V, VEEOUT = 0V, TIMER = GND VEEIN = –12V, VEEOUT = –11V, TIMER = GND ● ● 50 250 200 450 425 750 mA mA TTS Thermal Shutdown Temperature VPG(TH) Power Good Threshold Voltage V12VOUT Rising VVEEOUT Falling V3VOUT Rising V5VOUT Rising ● ● ● ● 10.8 –10.2 2.8 4.5 11.1 –10.5 2.9 4.65 VPGH Power Good Hysteresis 3VOUT 5VOUT 12VOUT, VEEOUT VIL Input Low Voltage ON, AUXON ● VIH Input High Voltage ON, AUXON ● VOL Output Low Voltage FAULT, PWRGD , IOL = 3mA ● IIN AUXON Pin Input Current AUXON = GND AUXON = VAUXIN ● ● ON Pin Input Current ON = GND ON = V12VIN 5VSENSE Input Current 11.4 –10.8 3.0 4.78 20 30 50 V V V V mV mV mV 0.8 V 2 V 0.4 V ±0.08 ±0.08 ±10 ±10 µA µA ● ● ±0.08 ±0.08 ±10 ±10 µA µA 5VSENSE = 5V ● 50 100 µA 3VSENSE Input Current 3VSENSE = 3V ● 50 100 µA 5VIN Input Current 5VIN = 5V ● 580 900 µA 3VIN Input Current 3VIN = 3V ● 310 550 µA 5VOUT Input Current 5VOUT = 5V, ON = V12VIN ● 260 500 µA ● 150 350 µA 3VOUT Input Current 3VOUT = 3V, ON = V12VIN RDIS 5VOUT Discharge Impedance 3VOUT Discharge Impedance 12VOUT Discharge Impedance VEEOUT Discharge Impedance ON = GND ON = GND ON = GND ON = GND ITIMER TIMER Pin Current Timer On, VTIMER = GND, Timer Off, VTIMER = 5V, VTIMER VAUXCB °C 150 Ω Ω Ω Ω 60 50 450 1600 ● –15 –22 45 –27 µA mA TIMER Threshold Voltage (V12VIN – VTIMER) ● 0.5 0.9 1.3 V Circuit Breaker Trip Voltage (VAUXIN – VAUXSENSE) ● 40 50 60 mV IAUXGATE AUXGATE Gate Output Current AUXON High, FAULT High, VAUXGATE = GND AUXON Low, FAULT High, VAUXGATE = 5V AUXON High, FAULT Low, VAUXGATE = 10V ● –6 –10 200 50 –14 µA µA mA ∆VAUXGATE External AUXGATE Gate Voltage (VAUXGATE – VAUXIN), VAUXIN = 3.3V ● 5 8 11 V Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2 : All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to ground unless otherwise specified. Note 3 : An internal zener on the AUXGATE pin clamps the charge pump voltage to a typical maximum operating voltage of 12V. External overdrive of the AUXGATE pin beyond the internal zener voltage may damage the device. sn4241 4241f 3 LTC4241 U W TYPICAL PERFOR A CE CHARACTERISTICS 3.3V and 5V Current Foldback Profile 4 3VIN = 3.3V 5VIN = 5V RSENSE = 0.005Ω 0.5 800 700 600 500 400 300 1.5 2.5 3.5 4.5 OUTPUT VOLTAGE (V) 0 1 2 12VIN Current Limit vs Temperature 40 30 20 5VOUT = 0V 1200 60 3VOUT = 3.3V 1000 50 CURRENT LIMIT (mA) CURRENT LIMIT VOLTAGE (mV) CURRENT LIMIT VOLTAGE (mV) 50 40 30 20 3VOUT = 0V 10 0 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 100 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G07 12VOUT = 0V 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G06 GATE, AUXGATE Output Source Current vs Temperature 54 GATE OUTPUT SOURCE CURRENT (µA) CIRCUIT BREAKER TRIP VOLTAGE (mV) VEEOUT = 0V 400 53 52 51 50 49 48 47 46 45 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G08 90 12.5 80 12.0 11.5 70 GATE 60 11.0 50 10.5 40 10.0 AUXGATE 30 9.5 20 9.0 10 –75 –50 –25 AUXGATE OUTPUT SOURCE CURRENT (µA) 200 600 0 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 55 600 300 800 200 (VAUXIN – VAUXSENSE) Circuit Breaker Trip Voltage vs Temperature 400 12VOUT = 11V 4241 • G05 VEEIN Current Limit vs Temperature VEEOUT = –11V 0 –1 –2 –3 –4 –5 –6 –7 –8 –9 –10 –11 –12 OUTPUT VOLTAGE (V) 4241 • G03 3VIN Current Limit Voltage vs Temperature 4241 • G04 CURRENT LIMIT (mA) 300 4241 • G02 5VOUT = 5V 0 –75 –50 –25 400 0 3 4 5 6 7 8 9 10 11 12 OUTPUT VOLTAGE (V) 70 500 500 100 5.5 70 0 –75 –50 –25 600 200 5VIN Current Limit Voltage vs Temperature 10 700 100 4241 • G01 60 800 200 0 VEEIN = –12V 900 OUTPUT CURRENT (mA) 6 0 1000 900 5VOUT 8 2 1100 12VIN = 12V 1000 3VOUT OUTPUT CURRENT (mA) OUTPUT CURRENT (A) 10 –12V Current Foldback Profile 12V Current Foldback Profile 1100 12 8.5 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G09 sn4241 4241f 4 LTC4241 U W TYPICAL PERFOR A CE CHARACTERISTICS GATE, AUXGATE Output Sink Current vs Temperature 300 GATE 250 AUXGATE 150 100 50 –75 –50 –25 80 8.20 70 8.15 AUXIN = 3.3V 60 AUXGATE 50 40 GATE 30 20 10 10.85 300 275 250 225 200 175 150 125 100 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) Power Good Threshold Voltage vs Temperature (12VOUT) POWER GOOD THRESHOLD VOLTAGE (V) POWER GOOD THRESHOLD VOLTAGE (V) 11.00 10.95 10.90 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G16 140 120 100 80 60 40 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) Power Good Threshold Voltage vs Temperature (3VOUT) 2.915 4.67 4.66 4.65 4.64 4.63 4.62 4.61 4.60 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G15 4.68 11.05 160 Power Good Threshold Voltage vs Temperature (5VOUT) 11.20 11.10 IVEEIN = 100mA 180 4241 • G14 4241 • G13 11.15 0 25 50 75 100 125 150 TEMPERATURE (°C) 200 I12VOUT = 500mA POWER GOOD THRESHOLD VOLTAGE (V) 10.70 –75 –50 –25 7.85 VEE Internal Switch Voltage Drop vs Temperature INTERNAL SWITCH VOLTAGE DROP (mV) INTERNAL SWITCH VOLTAGE DROP (mV) AUXGATE VOLTAGE (V) 11.00 7.90 4241 • G12 325 11.15 7.95 12V Internal Switch Voltage Drop vs Temperature 11.75 11.30 8.00 4241 • G11 AUXGATE Voltage vs Temperature 11.45 8.05 7.75 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G10 11.60 8.10 7.80 0 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) (VAUXGATE – VAUXIN) (V) FAST PULL-DOWN CURRENT (mA) OUTPUT SINK CURRENT (µA) 350 200 (VAUXGATE – VAUXIN) vs Temperature GATE, AUXGATE Fast Pull-Down Current vs Temperature 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G17 2.910 2.905 2.900 2.895 2.890 2.885 2.880 2.875 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G18 sn4241 4241f 5 LTC4241 U W TYPICAL PERFOR A CE CHARACTERISTICS Power Good Threshold Voltage vs Temperature (VEEOUT) Timer Threshold Voltage vs Temperature Timer Current vs Temperature 23.00 0.950 V12VIN – VTIMER –10.55 –10.50 –10.45 –10.40 –10.35 –10.30 –75 –50 –25 0.925 22.75 0.900 22.50 TIMER CURRENT (µA) TIMER THRESHOLD VOLTAGE (V) 0.875 0.850 0.825 0.800 21.00 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 12VIN Undervoltage Lockout Threshold vs Temperature 700 9.20 650 2.8 5VIN SUPPLY CURRENT (µA) 600 2.7 2.6 2.5 2.4 550 AUXIN 500 450 VEEIN 400 350 3VIN 300 2.3 250 2.2 –75 –50 –25 200 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 0 25 50 75 100 125 150 TEMPERATURE (°C) 5VIN Undervoltage Lockout Threshold vs Temperature 3.825 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G25 (V5VIN – V5VSENSE) CIRCUIT BREAKER TRIP FILTER TIME (µs) UNDERVOLTAGE LOCKOUT THRESHOLD (V) 3.850 9.00 8.95 8.90 8.85 8.80 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 2.625 AUXIN 2.600 2.575 2.550 2.525 2.500 3VIN 2.475 2.450 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G26 18.50 8.3 18.25 8.2 8.1 18.00 VAUXIN – VAUXSENSE 17.75 8.0 17.50 7.9 17.25 7.8 V5VIN – V5VSENSE 17.00 7.7 16.75 7.6 16.50 –75 –50 –25 7.5 0 25 50 75 100 125 150 TEMPERATURE (°C) (VAUXIN – VAUXSENSE) CIRCUIT BREAKER TRIP FILTER TIME (µs) 3.875 9.05 (V5VIN – V5VSENSE), (VAUXIN – VAUXSENSE) Circuit Breaker Trip Filter Time vs Temperature 2.650 3.900 9.10 4241 • G24 3VIN, AUXIN Undervoltage Lockout Threshold vs Temperature 3.925 9.15 4241 • G23 4241 • G22 3.950 0 25 50 75 100 125 150 TEMPERATURE (°C) 4241 • G21 VEEIN, 5VIN, 3VIN, AUXIN Supply Current vs Temperature 2.9 SUPPLY CURRENT (mA) 21.50 4241 • G20 12VIN Supply Current vs Temperature UNDERVOLTAGE LOCKOUT THRESHOLD (V) 21.75 21.25 4241 • G19 3.800 –75 –50 –25 22.00 0.775 0.750 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 22.25 UNDERVOLTAGE LOCKOUT THRESHOLD (V) POWER GOOD THRESHOLD VOLTAGE (V) –10.60 4241 • G27 sn4241 4241f 6 LTC4241 U U U PI FU CTIO S 12VIN (Pin 1): 12V Supply Input. This pin powers the primary controller internal circuitry. A 0.5Ω switch is connected between 12VIN and 12VOUT with a foldback current limit. An undervoltage lockout circuit prevents the switches from turning on while the 12VIN pin voltage is less than 9V. VEEIN (Pin 2): –12V Supply Input. A 1.2Ω switch is connected between VEEIN and VEEOUT with a foldback current limit. 3VOUT (Pin 3): 3.3V Output Monitor. Used to monitor the 3.3V output supply voltage. The PWRGD signal cannot go low until the 3VOUT pin exceeds 2.9V. TIMER (Pin 4): Current Limit Fault Timer Input. Connect a capacitor from TIMER to ground. With the primary controller turned off (ON = GND) or the internal circuit breaker tripped due to a PCI supply fault (FAULT = low), the TIMER pin is internally held at ground. When the primary controller is turned on, a 22µA pull-up current source is connected to TIMER. Current limit faults from the PCI supplies will be ignored until the voltage at the TIMER pin rises to within 0.9V of 12VIN. ON (Pin 5): On Control Input. A rising edge turns on the external N-channel FETs for 3.3V and 5V PCI supplies, the internal 12V and –12V switches and a falling edge turns it off. If the ON pin is cycled low then high following the trip of the circuit breaker due to a PCI supply fault, the circuit breaker is reset. FAULT (Pin 6): Fault Output. Open drain logic output used by both the primary and auxiliary controller to indicate an overcurrent fault condition. When any of the PCI and 3.3V auxiliary supplies are in current limit fault, the controller detecting the fault (primary or auxiliary) will be latched off and the FAULT pin will be pulled low. Current limit faults from the PCI supplies are ignored while the voltage at the TIMER pin is less than (12VIN – 0.9V). The current limit fault detected by the primary controller will not cause the auxiliary controller to latch off and vice versa. PWRGD (Pin 7): Power Good Output. Open drain logic output used by the primary controller to indicate the voltage status of the PCI supplies. PWRGD remains low while V12VOUT ≥ 11.1V, V3VOUT ≥ 2.9V, V5VOUT ≥ 4.65V, VVEEOUT ≤ –10.5V. When one of the supplies falls below its power good threshold voltage, PWRGD will go high after a 15µs deglitching time. The switches will not be turned off when PWRGD goes high. GND (Pin 8): Chip Ground AUXGATE (Pin 9): High Side Gate Drive for the 3.3V Auxiliary External N-channel MOSFET. An internal charge pump generates at least 8V of gate drive from a 3.3V auxiliary supply. A zener clamps AUXGATE approximately 12V above the supply voltage at AUXIN. The rise time at AUXGATE is set by an external AUXGATE capacitor connected to ground and an internal 10µA current source provided by the charge pump. If the circuit breaker trips or the auxiliary supply voltage hits the undervoltage lockout threshold, a 50mA current sink rapidly pulls AUXGATE low. AUXSENSE (Pin 10): 3.3V Auxiliary Circuit Breaker Current Sense Input. The load current is monitored by a sense resistor connected between AUXIN and AUXSENSE. The circuit breaker trips if the voltage across the sense resistor exceeds 50mV and the AUXGATE pin voltage will be turned off. AUXIN (Pin 11): 3.3V Auxiliary Supply Input. This pin powers the auxiliary controller internal circuitry. An undervoltage lockout circuit disables the AUXGATE pin until the supply voltage at AUXIN is greater than 2.6V. AUXGATE is held at ground potential until the undervoltage lockout deactivates. If no 3.3V auxiliary supply is available, tie AUXIN to ground. AUXON (Pin 12): ON Control Input for Auxiliary Supply. A rising edge turns on the external N-channel FET for 3.3V auxiliary supply and a falling edge turns it off. If the AUXON pin is cycled low then high following the trip of the circuit breaker due to a 3.3V auxiliary supply fault, the circuit breaker is reset. 3VIN (Pin 13): 3.3V Supply Sense Input. An undervoltage lockout circuit prevents the switches from turning on when the voltage at the 3VIN pin is less than 2.5V. If no 3.3V input supply is available, tie 3VIN to the 5VIN pin. 3VSENSE (Pin 14): 3.3V Current Limit Set Pin. With a sense resistor placed in the supply path between 3VIN and 3VSENSE, the GATE pin voltage will be adjusted to maintain sn4241 4241f 7 LTC4241 U U U PI FU CTIO S a constant voltage across the sense resistor and a constant current through the switch. A foldback feature makes the current limit decrease as the voltage at the 3VOUT pin approaches ground. To disable the current limit, 3VSENSE and 3VIN can be shorted together. GATE (Pin 15): High Side Gate Drive for the 3.3V and 5V PCI Supplies External N-channel MOSFETs. Requires an external series RC network for the current limit loop compensation and setting the minimum ramp-up rate. During power-up, the slope of the voltage rise at the GATE is set by the internal 60µA pull up current source and the external GATE capacitor connected to ground. During power-down, the slope of the falling voltage is set by the 200µA current source connected to ground and the external GATE capacitor. 5VSENSE (Pin 16): 5V Current Limit Set Pin. With a sense resistor placed in the supply path between 5VIN and 5VSENSE, the GATE pin voltage will be adjusted to maintain a constant voltage across the sense resistor and a constant current through the switch. A foldback feature makes the current limit decrease as the voltage at the 5VOUT pin approaches ground. To disable the current limit, 5VSENSE and 5VIN can be shorted together. 5VIN (Pin 17): 5V Supply Sense Input. Used to monitor the 5V input supply voltage. An undervoltage lockout circuit prevents the switches from turning on when the voltage at the 5VIN pin is less than 3.9V. 5VOUT (Pin 18): 5V Output Monitor. Used to monitor the 5V output supply voltage. The PWRGD signal cannot go low until the 5VOUT pin exceeds 4.65V. VEEOUT (Pin 19): –12V Supply Output. A 1.2Ω switch is connected between VEEIN and VEEOUT. VEEOUT must fall below –10.5V before the PWRGD signal can go low on the LTC4241. 12VOUT (Pin 20): 12V Supply Output. A 0.5Ω switch is connected between 12VIN and 12VOUT. 12VOUT must exceed 11.1V before the PWRGD signal can go low on the LTC4241 sn4241 4241f 8 LTC4241 W BLOCK DIAGRA 5VIN 5VSENSE GATE 3VSENSE 3VIN 17 16 15 14 13 + – 5VOUT 60µA + 55mV +– ON 5 PWRGD 7 + – 12VIN 18 3VOUT 55mV – 200µA Q5 3.9V UVL 3 + A2 A1 – 3VOUT 5VOUT Q8 Q7 –+ 2.5V UVL CP1 + Q3 – REF PRIMARY CONTROL LOGIC FAULT CP2 6 + Q4 – 9V UVL REF 12VIN Q9 REF Q10 Q2 Q1 22µA CP4 + + CP3 Q6 – – PCI-BUS HOT SWAP CONTROLLER REF 1 20 4 2 19 8 12VIN 12VOUT TIMER VEEIN VEEOUT GND Q12 CHARGE PUMP AUXIN 11 + – 50mV + 8µs FILTER A3 AUXSENSE 10 – AUXILIARY CONTROL LOGIC 10µA 9 AUXGATE Q11 Z1 12V 2.6V UVL Z2 20V 200µA AUXIN AUXON 12 3.3V AUXILIARY SUPPLY HOT SWAP CONTROLLER 4241 BD sn4241 4241f 9 LTC4241 U W U U APPLICATIO S I FOR ATIO Hot Circuit Insertion When a circuit board is inserted into a live PCI slot, the supply bypass capacitors on the board can draw huge transient currents from the PCI power bus as they charge up. The transient currents can cause permanent damage to the connector pins and glitches the power bus, causing other boards in the system to reset. The LTC4241 is designed to turn a board’s supply voltages on and off in a controlled manner, allowing the board to be safely inserted or removed from a live PCI slot without glitching the system power supplies. The chip also protects the PCI supplies from shorts and monitors the supply voltages. The LTC4241 is designed for motherboard applications and includes an additional independent controller for the 3.3V auxiliary supply. LTC4241 Feature Summary 8. Fault control: the current limit fault detected by either the primary or auxiliary controller will not cause the other controller to latch off. Both controllers use the FAULT output to indicate a fault condition. 9. Space saving 20-pin narrow SSOP package. PCI Power Requirements PCI systems usually require four power rails: 5V, 3.3V, –12V and 12V. Systems implementing the 3.3V signaling environment are usually required to provide all four rails in every system. A 3.3V auxiliary supply is added in the PCI system to power PCI logic functions that need to remain active when the rest of the system is unpowered. The tolerance of the supplies as measured at the components is summarized in Table 1. Table 1. PCI Power Supply Requirements 1. Allows safe board insertion and removal from a motherboard. SUPPLY TOLERANCE CAPACITIVE LOAD 5V 5V ± 5% <3000µF 2. Primary controller to control the four PCI supplies: 3.3V, 5V, –12V, 12V and an independent auxiliary controller to control the 3.3V auxiliary supply. 3.3V 3.3V ± 0.3V <3000µF 12V 12V ± 5% <500µF –12V –12V ± 10% <120µF 3.3VAUX 3.3V ± 0.3V <500µF 3. Adjustable foldback current limit for PCI supplies: an adjustable analog current limit with a value that depends on the output voltage. If the output is shorted to ground, the current limit drops to keep power dissipation and supply glitches to a minimum. 4. Electronic circuit breaker for all supplies: if a supply remains in current limit for too long, the circuit breaker will trip, the supplies will be turned off and the FAULT pin pulled low. 5. Current limit power-up: the four PCI supplies are allowed to power up in current limit. This allows the chip to power up boards with a wide range of capacitive loads without tripping the circuit breaker. The maximum allowable power-up time is programmable using the TIMER pin. 6. On-Chip –12V and 12V power switches 7. Power good output: monitors the voltage status of the four PCI supply voltages. The 3.3V auxiliary supply is not monitored. 10 Power-Up Sequence for PCI Power Supplies The PCI power supplies are controlled by placing external N-channel pass transistors in the 3.3V and 5V power paths, and internal pass transistors for the 12V and –12V power paths (Figure 1). Resistors R1 and R2 provide a current signal for fault detection and R7 and C1 provide current control loop compensation. Resistors R4 and R5 prevent high frequency oscillations in Q1 and Q2. When the ON pin is pulled high, the GATE pin is pulled high by an internal 60µA current source and the pass transistors are allowed to turn on. The internal 12V and –12V switches are also turned on and a 22µA current source is connected to the TIMER pin (Figure 2). sn4241 4241f LTC4241 U W U U APPLICATIO S I FOR ATIO ON 10V/DIV ON 10V/DIV TIMER 10V/DIV TIMER 10V/DIV GATE 10V/DIV GATE 10V/DIV 12VOUT 5V/DIV 12VOUT 5V/DIV 5VOUT 5V/DIV 3VOUT 5V/DIV 5VOUT 5V/DIV 3VOUT 5V/DIV VEEOUT 5V/DIV VEEOUT 5V/DIV FAULT 10V/DIV FAULT 10V/DIV PWRGD 10V/DIV PWRGD 10V/DIV 10ms/DIV 10ms/DIV 4241 F02 Figure 3. Normal Power-Down Sequence Figure 2. Normal Power-Up Sequence The current in each pass transistor increases until it reaches the current limit for each supply. Each supply is allowed to power up at the rate dV/dt = 60µA/C1 or as determined by the current limit and the load capacitance on the supply line, whichever is slower. Current limit faults are ignored while the TIMER pin voltage is ramping up and is less than 0.9V below 12VIN. Once all four PCI supply voltages are within tolerance, the PWRGD pin will pull low. Power-Down Sequence for PCI Power Supplies When the ON pin is pulled low, a power-down sequence begins for all the PCI power supplies (Figure 3). Internal switches are connected to each of the output supply voltage pins to discharge the load capacitors to ground. The TIMER pin is immediately pulled low and the internal 12V and –12V switches are turned off. The GATE pin is pulled to ground by an internal 200µA current source. This turns off the external pass transistors in a controlled manner and prevents the load current on the 3.3V and 5V supplies from going to zero instantaneously and glitching the power supply voltages. When any of the output voltages dips below its threshold, the PWRGD pin pulls high. 4241 F03 Timer During a power-up sequence for the PCI power supplies, a 22µA current source is connected to the TIMER pin and current limit faults are ignored until the voltage ramps to within 0.9V of 12VIN. This feature allows the chip to power up a PCI slot that can accommodate boards with a wide range of capacitive loads on the supplies. The power-up time for any one of the four outputs will be: C •V tON ≅ 2 • LOAD OUT ILIMIT – ILOAD For example, for CLOAD = 2000µF, VOUT = 5V, ILIMIT = 7A, ILOAD = 5A, the 5VOUT turn-on time will be ~10ms. By substituting the variables in the above equation with the appropriate values, the turn-on time for the other three outputs can be calculated. The timer period should be set longer than the maximum supply turn-on time but short enough to not exceed the maximum safe operating area of the pass transistor during a short-circuit. The timer period is given by: tTIMER = C TIMER • 11.1V 22µA sn4241 4241f 11 LTC4241 U W U U APPLICATIO S I FOR ATIO For CTIMER = 0.1µF, the timer period will be ~50ms. The TIMER pin is immediately pulled low when ON goes low. Thermal Shutdown The internal switches for the 12V and –12V supplies are protected by an internal current limit and thermal shutdown circuit. When the temperature of the chip reaches 150°C, only the switches controlling the PCI supplies will be latched off and the FAULT pin will be pulled low. Short-Circuit Protection for PCI Power Supplies During a normal power-up sequence for the PCI power supplies, if the TIMER is done ramping and any supply is still in current limit, all of the pass transistors will be immediately turned off, the TIMER and FAULT pin will be pulled low as shown in Figure 4. spikes — for example, from a fan turning on — from causing false trips of the circuit breaker. The chip will stay in the latched-off state until the ON pin is cycled low then high, or the 12VIN supply is cycled. To prevent excessive power dissipation in the pass transistors and to prevent voltage spikes on the supplies during short-circuit conditions, the current limit on each PCI supply, except the 3.3V auxiliary supply, is designed to be a function of the output voltage. As the output voltage drops, the current limit decreases. Unlike a traditional circuit breaker function where huge currents can flow before the breaker trips, the current foldback feature assures that the supply current will be kept at a safe level and prevent voltage glitches when powering up into a short. ON 10V/DIV ON 10V/DIV TIMER 10V/DIV TIMER 10V/DIV GATE 10V/DIV GATE 10V/DIV 12VOUT 5V/DIV 12VOUT 5V/DIV 5VOUT 5V/DIV 3VOUT 5V/DIV 5VOUT 5V/DIV 3VOUT 5V/DIV VEEOUT 5V/DIV VEEOUT 5V/DIV FAULT 10V/DIV PWRGD 10V/DIV FAULT 10V/DIV PWRGD 10V/DIV 20ms/DIV 4241 F04 20ms/DIV 4241 F05 Figure 4. Power-Up into a Short on 3.3V Output Figure 5. Short-Circuit on 5V Followed by Circuit Breaker Reset If a short-circuit occurs after the PCI supplies are powered up, the shorted supply’s current will drop immediately to the limit value (Figure 5). The current limit and the foldback current level for the 5V and 3.3V outputs are both a function of the external sense resistor (R1 for 5VOUT and R2 for 3VOUT, see Figure 1). As shown in Figure 1, a sense resistor is connected between 5VIN and 5VSENSE for the 5V supply. For the 3V supply, a sense resistor is connected between 3VIN and 3VSENSE. If the supply remains in current limit for more than 17µs, all of the PCI supplies except the 3.3V auxiliary supply will be latched off. The 17µs delay prevents quick current sn4241 4241f 12 LTC4241 U W U U APPLICATIO S I FOR ATIO The current limit and the foldback current level (at the VOUT = 0V) are given by: ILIMIT = 55mV/RSENSE IFOLDBACK = 9mV/RSENSE As a design aid, the current limit and foldback level for commonly used values for RSENSE are given in Table 2. Table 2. ILIMIT and IFOLDBACK vs RSENSE RSENSE (Ω) ILIMIT IFOLDBACK 0.005 11A 1.8A 0.006 9.2A 1.5A 0.007 7.9A 1.3A 0.008 6.9A 1.1A 0.009 6.1A 1.0A 0.01 5.5A 0.9A The current limit for the internal 12V switch is set at 850mA folding back to 300mA and the –12V switch at 450mA folding back to 200mA. In systems where it is possible to exceed the current limit for a short amount of time, it might be necessary to prevent the analog current loop from responding quickly so the output voltage does not droop. This can be accomplished by adding an RC filter across the sense resistor as shown in Figure 6. RF should be 20Ω or less to prevent offset errors. A capacitor, CF, of 0.1µF gives a delay of about 1.5µs and a 1µF capacitor gives a delay of about 15µs. 5VIN 3 4 CF 1µF 17 * ADDITIONAL PINS OMITTED FOR CLARITY Q1 IRF7413 R1 1 0.007Ω 2 5VIN 16 5VSENSE 15 18 GATE 5VOUT When power is first applied to VAUXIN, the AUXGATE pin pulls low. A low-to-high transition at the AUXON pin initiates the AUXGATE ramp up (Figure 7). The AUXGATE is pulled high by an internal 10µA current source and the pass transistor is allowed to turn on. As the auxiliary controller does not have the foldback current limit feature and timer control, the inrush supply current during powerup is limited by ramping the gate of the pass transistor at a controlled rate (dV/dt = 10µA/C3) where C3 is the total external capacitance between AUXGATE and ground. With proper selection of the C3 capacitance value, the inrush current (I = CLOAD • dV/dt = 10µA • CLOAD/C3) is limited to a value less than the current limit set by the sense resistor R3. This prevents the circuit breaker from tripping during power-up. CLOAD is the total load capacitance on the 3.3V auxiliary supply line. For example, for C3 = 10nF, CLOAD = 470µF, R3 = 0.07Ω, ILIMIT = 0.7A, the inrush current will be 0.47A < ILIMIT. The ramp-up time for 3.3VAUX output to reach its final value is equal to t = (VAUXIN • C3)/10µA. A high-to-low transition at the AUXON pin initiates a AUXGATE ramp-down at a slope of –200µA/C3 as the AUXGATE is pulled to ground by an internal 200µA current source. This will allow the load capacitance on the supply line to discharge while the AUXGATE pulls low to turn off the external N-channel pass transistor. 5VOUT 5A AUXON 2V/DIV R4 10Ω RF 20Ω power path (Figure 1). The resistor R3 provides load current fault detection and R6 prevents high frequency oscillation in Q3. R7 100Ω C1 0.047µF AUXGATE 5V/DIV LTC4241* 3.3VAUX 2V/DIV Figure 6. Delay in the Current Limit Loop Power-Up/Down Sequence for 3.3V Auxiliary Supply The 3.3V auxiliary supply is controlled by placing an external N-channel pass transistor Q3 in the 3.3VAUX 5ms/DIV 4241 F07 Figure 7. Power-Up/Down Sequence for 3.3V Auxiliary Supply sn4241 4241f 13 LTC4241 U W U U APPLICATIO S I FOR ATIO Electronic Circuit Breaker for 3.3V Auxiliary Supply Supply Bypass Capacitors An electronic circuit breaker is used to protect against excessive load current and short-circuits on the 3.3V auxiliary supply. The load current is monitored by placing a sense resistor R3 between AUXIN and AUXSENSE as shown in Figure 1. The circuit breaker trip threshold is 50mV and exhibits a response time of 8µs. Unlike the PCI supplies which use the current foldback limit with circuit breaker during short-circuits, here the circuit breaker will trip and immediately pull AUXGATE to ground if the voltage between AUXIN and AUXSENSE exceeds 50mV for more than 8µs. The external N-channel transistor is turned off and FAULT is pulled low. The circuit breaker is reset when AUXON is cycled low then high, or the AUXIN supply is cycled. If the circuit breaker feature is not required, the AUXSENSE pin can be shorted to AUXIN. In motherboard applications, large bypass capacitors are recommended at each of the system power supplies to minimize supply glitches as a result of board insertion. A supply bypass capacitor of ≥100µF at 12VIN connection is recommended. The trip current of the circuit breaker is set by: As a design aid, the trip current for commonly used values for R3 is given in Table 3. Table 3. ITRIP vs R3 ITRIP 0.05 1A 0.06 833mA 0.07 714mA 0.08 625mA 0.09 556mA 0.1 500mA CURRENT FLOW TO LOAD SENSE RESISTOR TRACK WIDTH W: 0.03" PER AMPERE ON 1 OZ COPPER FOIL W 4241 F08 5VIN 5VSENSE Figure 8. Making PCB Connections to the Sense Resistor for the 5V Rail PCB Layout Considerations for the Sense Resistor ITRIP = 50mV/R3 R3 (Ω) CURRENT FLOW FROM SUPPLY For proper circuit breaker operation, 4-wire Kelvin-sense connections between the sense resistor and the LTC4241’s 5VIN and 5VSENSE pins, 3VIN and 3VSENSE pins and AUXIN and AUXSENSE pins are strongly recommended. The drawing in Figure 8 illustrates the correct way of making connections between the LTC4241 and the sense resistor. PCB layout should be balanced and symmetrical to minimize wiring errors. In addition, the PCB layout for the sense resistors and the power MOSFETs should include good thermal management techniques for optimal sense resistor power dissipation. Power MOSFET and Sense Resistor Selection If more than 8µs of response time is needed to reject supply current ripple noise, an external resistor, RF, of 20Ω and capacitor, CF, of 1µF (Figure 6) can be added to the AUXSENSE circuit. This will give a delay of 15µs. Table 4 lists some available N-channel power MOSFETs . Table 5 lists some current sense resistors that can be used with the LTC4241’s circuit breakers. Table 6 lists the supplier web site addresses for discrete components mentioned throughout this datasheet. Table 4. N-Channel Power MOSFET Selection Guide CURRENT RATING PART NUMBER PACKAGE VDS MAX VGSMAX RDS(on) MANUFACTURER 8.0A Si4412ADY SO-8 30V ±20V 0.024Ω Vishay-Siliconix 3.5A Si2306DS SOT-23 30V ±20V 0.057Ω Vishay-Siliconix 10A Si4410DY SO-8 30V ±20V 0.013Ω Vishay-Siliconix 13A IRF7413 SO-8 30V ±20V 0.011Ω International Rectifier 2.7A FDN 359AN SOT-23 30V ±20V 0.046Ω Fairchild Semiconductor sn4241 4241f 14 LTC4241 U W U U APPLICATIO S I FOR ATIO Table 5. Sense Resistor Selection Guide CURRENT LIMIT VALUE PART NUMBER DESCRIPTION MANUFACTURER 0.7A WSL2010R07 0.07Ω, 0.5W, 1% Resistor Vishay-Dale 1A LR120601R055F WSL2010R055 0.055Ω, 0.5W, 1% Resistor IRC-TT Vishay-Dale 2A LR120601R028F WSL2010R028 0.028Ω, 0.5W, 1% Resistor IRC-TT Vishay-Dale 5A LR120601R011F WSL2010R011 0.011Ω, 0.5W, 1% Resistor IRC-TT Vishay-Dale 7.9A WSL2512R007 0.007Ω, 1W, 1% Resistor Vishay-Dale 11A WSL2512R005 0.005Ω, 1W, 1% Resistor Vishay-Dale Table 6. Manufacturers’ Web Site MANUFACTURER WEB SITE International Rectifier www.irf.com Fairchild Semiconductor www.fairchildsemi.com IRC-TT www.irctt.com Vishay-Dale www.vishay.com Vishay-Siliconix www.vishay.com Diodes, Inc. www.diodes.com U PACKAGE DESCRIPTIO GN Package 20-Lead Plastic SSOP (Narrow .150 Inch) (Reference LTC DWG # 05-08-1641) .337 – .344* (8.560 – 8.737) .045 ±.005 20 19 18 17 16 15 14 13 12 .254 MIN .150 – .165 .0165 ± .0015 11 .229 – .244 (5.817 – 6.198) .058 (1.473) REF .150 – .157** (3.810 – 3.988) .0250 TYP 1 RECOMMENDED SOLDER PAD LAYOUT .015 ± .004 × 45° (0.38 ± 0.10) .007 – .0098 (0.178 – 0.249) 2 3 4 5 6 7 8 .053 – .068 (1.351 – 1.727) 9 10 .004 – .0098 (0.102 – 0.249) 0° – 8° TYP .016 – .050 (0.406 – 1.270) .008 – .012 (0.203 – 0.305) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) .0250 (0.635) BSC 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE GN20 (SSOP) 0502 sn4241 4241f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC4241 U TYPICAL APPLICATIO GND R1 1 0.007Ω 2 SYSTEM POWER SUPPLY C3 10nF 11 1 2 12 5 PCI POWER SYSTEM CONTROLLER R8 10k 6 R9 10k 7 3.3VAUX 500mA 4 3 8 R4 10Ω Q3 Si4412ADY 1 0.07Ω 2 5V 5A 4 3 R3 Q1 IRF7413 10 AUXIN AUXSENSE R7 100Ω C1 0.047µF R6 10Ω 9 13 17 AUXGATE 3VIN 14 16 15 5VIN 3VSENSE 5VSENSE GATE 3 18 3VOUT 5VOUT GND 12VIN VEEIN 12VOUT AUXON LTC4241 ON VEEOUT FAULT TIMER 20 12V 500mA 19 –12V 100mA 4 BACKPLANE CONNECTOR C2 0.1µF PWRGD 4241 F09 Figure 9. System Without 3.3V Supply RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1421 2-Channel Hot Swap Controller Operates from 3V to 12V and Supports –12V LTC1422 Hot Swap Controller in SO-8 System Reset Output with Programmable Delay LT1641-1/LT1641-2 High Voltage Hot Swap Controller Operates from 9V to 80V, SO-8 Package, Latch Off/Auto Retry LTC1642 Fault Protected Hot Swap Controller Operates Up to 16.5V, Protected to 33V LTC1643AL/LTC1643AL-1/LTC1643AH PCI-Bus Hot Swap Controller 3.3V, 5V and ±12V in Narrow 16-Pin SSOP Package LTC1644 CompactPCI Bus Hot Swap Controller 3.3V, 5V and ±12V, 1V Precharge, Local PCI Logic LTC1645 2-Channel Hot Swap Controller Operates from 1.2V to 12V, Power Sequencing LTC1646 CompactPCI Dual Hot Swap Controller 3.3V and/or 5V Supplies, 1V Precharge, Local PCI Reset Logic LTC1647-1/LTC1647-2/LTC1647-3 Dual Hot Swap Controllers Operates from 2.7V to 16.5V LTC4211 Single Channel, Hot Swap Controller 2.5V to 16.5V Operation, Multilevel Current Control, MSOP Package LTC4230 Triple Channel, Hot Swap Controller 1.7V to 16.5V Operation, Multilevel Current Control LT4250L/LT4250H – 48V Hot Swap Controller in S0-8 Operates from –20V to –80V, Active Current Limiting LTC4251 –48V Hot Swap Controller in S0T-23 –48V Hot Swap Controller, Active Current Limiting LTC4252 –48V Hot Swap Controller in MSOP Active Current Limiting With Drain Acceleration LTC4253 –48V Hot Swap Controller and Sequencer Active Current Limiting With Drain Acceleration and Three Sequenced Power Good Outputs LTC4350 Hot Swappable Load Share Controller Output Voltages from 1.5V to 12V CompactPCI is a trademark of the PCI Industrial Computer Manufactures Group ThinSOT is a trademark of Linear Technology Corporation sn4241 4241f 16 Linear Technology Corporation LT/TP 0303 2K • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2002