NCV7703B Triple Half-Bridge Driver with SPI Control The NCV7703B is a fully protected Triple Half−Bridge Driver designed specifically for automotive and industrial motion control applications. The three half−bridge drivers have independent control. This allows for high side, low side, and H−Bridge control. H−Bridge control provides forward, reverse, brake, and high impedance states. The drivers are controlled via a standard Serial Peripheral Interface (SPI). This device is fully compatible with ON Semiconductor’s NCV7708 Double Hex Driver. Features • • • • • • • • • • • • • • • • • Ultra Low Quiescent Current in Sleep Mode, 1 mA for VS and VCC Power Supply Voltage Operation down to 5 V 3 High−Side and 3 Low−Side Drivers Connected as Half−Bridges Internal Free−Wheeling Diodes Configurable as H−Bridge Drivers 0.5 A Continuous (1 A peak) Current RDS(on) = 0.8 W (typ) 5 MHz SPI Control with Daisy Chain Capability Compliance with 5 V and 3.3 V Systems Overvoltage and Undervoltage Lockout Fault Reporting 1.4 A Overcurrent Threshold Detection with Optional Shutdown 3 A Current Limit with Auto Shutdown Overtemperature Warning and Protection Levels Internally Fused Leads in SOIC−14 Package for Better Thermal Performance ESD Protection up to 6 kV These are Pb−Free Devices MARKING DIAGRAM 14 SOIC−14 D2 SUFFIX CASE 751A 14 1 • Automotive • Industrial • DC Motor Management VS VS NCV7703BG AWLYWW 1 NCV7703B = Specific Device Code A = Assembly Location WL = Wafer Lot Y = Year WW = Work Week G = Pb−Free Package PIN CONNECTIONS GND OUT3 VS CSB SI SCLK GND GND OUT1 OUT2 VCC EN SO GND ORDERING INFORMATION Device Typical Applications VS http://onsemi.com Package Shipping† NCV7703BD2G SOIC−14 (Pb−Free) 55 Units / Rail NCV7703BD2R2G SOIC−14 (Pb−Free) 2500 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. M OUT1 OUT2 M OUT3 Figure 1. Cascaded Application © Semiconductor Components Industries, LLC, 2010 April, 2010 − Rev. 0 1 Publication Order Number: NCV7703B/D NCV7703B VS EN ENABLE VCC Reference & Bias UVLO OSC DRIVE 1 VS clk clk VS Charge Pump Control Logic Fault Detect High−Side Driver Waveshaping VS OUT1 Low−Side Driver Channel Enable Waveshaping SI SPI SCLK Fault SO 16 Bit Logic and Latch CSB VS Undervoltage Lockout VS Overvoltage Lockout Under−Load Overcurrent Thermal Warning/Shutdown VS DRIVE 2 clk Channel Enable Fault OUT2 VS DRIVE 3 clk Channel Enable Fault OUT3 Figure 2. Block Diagram GND PACKAGE PIN DESCRIPTION Pin # Symbol 1 GND* Ground. Connect all grounds together. 2 OUT3 Half Bridge Output 3. 3 VS 4 CSB 5 SI Serial Input 6 SCLK Serial Clock 7 GND* Ground. Connect all grounds together. 8 GND* Ground. Connect all grounds together. 9 SO Serial Output 10 EN Enable. Logic high wakes the IC up from a sleep mode. 11 VCC Power supply input for internal logic. 12 OUT2 Half Bridge Output 2. 13 OUT1 Half Bridge Output 1. 14 GND* Ground. Connect all grounds together. Description Power Supply input for the output drivers and internal supply voltage. Chip Select Bar. Active low serial port operation. *Pins 1, 7, 8, and 14 are internally shorted together. It is recommended to also short these pins externally. http://onsemi.com 2 NCV7703B ENABLE Wake Up D1* 1N4001 NCV8518 RESET + WDI VBAT Vout D2** Delay 120k 22 mF GND VCC 10 mF VS OUT1 EN microprocessor M OUT2 CSB SI NCV7703B OUT3 SO GND M SCLK GND GND GND GND * D1 optional. For use where reverse battery protection is required. ** D2 optional. For use where load dump exceeds 40V. Figure 3. Application Circuit http://onsemi.com 3 − NCV7703B MAXIMUM RATINGS Rating Value Unit Power Supply Voltage (VS) (DC) (AC), t < 500 ms, Ivs > −2 A −0.3 to 40 −1 V Output Pin OUTx (DC) (AC), t < 500 ms, IOUTx > −2 A −0.3 to 40 −1 V Pin Voltage (Logic Input pins, SI, SCLK, CSB, SO, EN, VCC) −0.3 to 7 Output Current (OUTx) (DC) (AC) (50 ms pulse, 1 s period) V A −1.8 to 1.8 Internally Limited Electrostatic Discharge, Human Body Model, VS, OUT1, OUT2, OUT3 (Note 3) 6 kV Electrostatic Discharge, Human Body Model, all other pins (Note 3) 2 kV Electrostatic Discharge, Machine Model, VS, OUT1, OUT2, OUT3 (Note 3) 300 V Electrostatic Discharge, Machine Model, all other pins (Note 3) 200 V 1 kV Operating Junction Temperature −40 to 150 °C Storage Temperature Range −55 to 150 °C MSL3 − Electrostatic Discharge, Charge Device Model (Note 3) Moisture Sensitivity Level (MAX 260°C Processing) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Test Conditions (Typical Value) Thermal Parameters 14 Pin Fused SOIC Package Unit min−pad board (Note 1) 1″ pad board (Note 2) Junction−to−Lead (psi−JL8, YJL8) or Pins 1, 7, 8, 14 23 22 °C/W Junction−to−Ambient (RqJA, qJA) 122 83 °C/W mm2 1. 1−oz copper, 67 copper area, 0.062″ thick FR4. 2. 1−oz copper, 645 mm2 copper area, 0.062″ thick FR4. 3. This device series incorporates ESD protection and is tested by the following methods: ESD HBM tested per AEC−Q100−002 (EIA/JESD22−A114) ESD MM tested per AEC−Q100−003 (EIA/JESD22−A115) ESD CDM tested per EIA/JES D22/C101, Field Induced Charge Model http://onsemi.com 4 NCV7703B ELECTRICAL CHARACTERISTICS (−40°C ≤ TJ ≤ 150°C, 5.5 V ≤ VS ≤ 40 V, 3 V ≤ VCC ≤ 5.25 V, EN = VCC, unless otherwise specified) Conditions Min Typ Max Unit VS = 13.2 V, OUTx = 0 V EN = SI = SCLK = 0 V, CSB = VCC 0 V < VCC < 5.25 V (TJ = −40°C to 85°C) − 1.0 5.0 mA VS = 13.2 V, OUTx = 0 V EN = SI = SCLK = 0 V, CSB = VCC 0 V < VCC < 5.25 V, TJ = 25°C − − 2.0 Supply Current (VS) Active Mode EN = VCC, 5.5 V < VS < 35 V No Load − 2.0 4.0 mA Supply Current (VCC) Sleep Mode (Note 6) VCC = CSB, EN = SI = SCLK = 0 V (TJ = −40°C to 85°C) − 0 2.5 mA Supply Current (VCC) Active Mode EN = VCC − 1.5 3.0 mA Characteristic GENERAL Supply Current (VS) Sleep Mode (Note 5) VCC Power−On−Reset Threshold 2.60 2.80 3.00 V VS Undervoltage Detection Threshold VS decreasing Hysteresis 4.3 100 4.7 − 5.1 400 V mV VS Overvoltage Detection Threshold VS increasing Hysteresis 34.0 1.5 37.5 3.5 40.0 5.5 V Thermal Warning (Note 4) Threshold Hysteresis 120 − 145 30 170 − °C Thermal Shutdown (Note 4) Threshold Hysteresis 155 − 175 30 195 − °C 1.05 1.20 − °C/°C VS = 13.2 V, TJ = 25°C − 0.8 0.95 W VS = 13.2 V − − 1.5 W 8 V ≤ VS ≤ 40 V − − 1.7 W 5.5 V ≤ VS ≤ 8 V, TJ = 25°C − 1.3 − W 5.5 V ≤ VS ≤ 8 V − − 2.0 W VS = 13.2 V, TJ = 25°C − 0.8 0.95 W VS = 13.2 V − − 1.5 W 8 V ≤ VS ≤ 40 V − − 1.7 W 5.5 V ≤ VS ≤ 8 V, TJ = 25°C − 1.3 − W 5.5 V ≤ VS ≤ 8 V − − 2.0 W OUTx = 0 V, VS = 40 V, EN = 0 V CSB = VCC 0 V < VCC < 5.25 V Sum(I(OUTx) −5.0 − − mA OUTx = 0 V, VS = 40 V, EN = 0 V CSB = VCC 0 V < VCC < 5.25 V, TJ = 25°C Sum(I(OUTx) −1.0 − − Ratio of Thermal Shutdown to Thermal Warning temperature (Note 4) OUTPUTS Output RDS(on) (Source) Output RDS(on) (Sink) Source Leakage Current Sum of I(OUTx) x = 1, 2, 3 Iout = −500 mA Iout = 500 mA http://onsemi.com 5 NCV7703B ELECTRICAL CHARACTERISTICS (−40°C ≤ TJ ≤ 150°C, 5.5 V ≤ VS ≤ 40 V, 3 V ≤ VCC ≤ 5.25 V, EN = VCC, unless otherwise specified) Characteristic Conditions Min Typ Max Unit OUTx = VS = 40 V, EN = 0 V CSB = VCC 0 V < VCC < 5.25 V − − 300 mA OUTx = VS = 13.2 V, EN = 0 V CSB = VCC 0 V < VCC < 5.25 V, TJ = 25°C − − 10 OUTPUTS Sink Leakage Current Over Current Shutdown Threshold Source Sink −1.8 1.0 −1.4 1.4 −1.0 1.8 A Current Limit Source Sink −5.0 2.0 −3.0 3.0 −2.0 5.0 A Under Load Detection Threshold Source Sink −15 3.0 −7.0 7.0 −2.0 15 mA − 0.9 1.3 V Power Transistor Body Diode Forward Voltage If = 500 mA 4. Thermal characteristics are not subject to production test 5. For temperatures above 85°C, refer to Figure 4. 6. For temperatures above 85°C, refer to Figure 5. http://onsemi.com 6 NCV7703B ELECTRICAL CHARACTERISTICS (−40°C ≤ TJ ≤ 150°C, 5.5 V ≤ VS ≤ 40 V, 3 V ≤ VCC ≤ 5.25 V, EN = VCC, unless otherwise specified) Conditions Min Typ Max Input Threshold High Low − 30 − − 70 − Input Hysteresis 100 350 600 mV Characteristic Unit LOGIC INPUTS (EN, SI, SCLK, CSB) %VCC Input Pulldown Current (EN, SI, SCLK) EN = SI = SCLK = VCC 5.0 25 50 mA Input Pullup Current (CSB) CSB = 0 V −50 −25 −5 mA − 10 15 pF VCC – 1.0 VCC – 0.7 − V − 0.2 0.4 V −10 − 10 mA − 10 15 pF 10 10 25 25 50 50 − 200 − ms 200 350 600 ms Input Capacitance (Note 7) LOGIC OUTPUT (SO) Output High Iout = 1 mA Output Low Iout = −1.6 mA Tri−state Leakage CSB = VCC, 0 V v SO v VCC Tri−state Input Capacitance (Note 7) CSB = VCC TIMING SPECIFICATIONS Overcurrent Shutdown Delay Time Source Sink Current Limit Fault Delay ms VS > 8 V Under Load Detection Delay Time High Side Turn On Time VS = 13.2 V, Rload = 25 W − 7.5 15 ms High Side Turn Off Time VS = 13.2 V, Rload = 25 W − 3.0 6.0 ms Low Side Turn On Time VS = 13.2 V, Rload = 25 W − 6.5 15 ms Low Side Turn Off Time VS = 13.2 V, Rload = 25 W − 3.0 6.0 ms High Side Rise Time VS = 13.2 V, Rload = 25 W − 5.0 10 ms High Side Fall Time VS = 13.2 V, Rload = 25 W − 2.0 5.0 ms Low Side Rise Time VS = 13.2 V, Rload = 25 W − 1.0 3.0 ms Low Side Fall Time VS = 13.2 V, Rload = 25 W − 1.0 3.0 ms NonOverlap Time High Side Turn Off to Low Side Turn On 1.0 − − ms NonOverlap Time Low Side Turn Off to High Side Turn On 1.0 − − ms 7. Not production tested. http://onsemi.com 7 NCV7703B ELECTRICAL CHARACTERISTICS (−40°C ≤ TJ ≤ 150°C, 5.5 V ≤ VS ≤ 40 V, 3 V ≤ VCC ≤ 5.25 V, EN = VCC, unless otherwise specified) SERIAL PERIPHERAL INTERFACE Conditions Timing Chart # (See Figure 6) Min Typ Max Unit VCC = 5 V − − − 5 MHz VCC = 5 V VCC = 3.3 V − − 200 500 − − − − ns SI, SCLK − − − 15 pF SCLK High Time 1 85 − − ns SCLK Low Time 2 85 − − ns SCLK Setup Time 3 4 85 85 − − − − ns SI Setup Time 11 50 − − ns SI Hold Time 12 50 − − ns CSB Setup Time 5 6 100 100 − − − − ns CSB High Time (Note 9) 7 200 − − ns SO enable after CSB falling edge (Note 8) 8 − − 50 ns SO disable after CSB rising edge (Note 8) 9 − − 50 ns Characteristic SCLK Frequency SCLK Clock Period Maximum Input Capacitance (Note 8) SO Rise Time VCC = 5 V, Cload = 40 pF − − 10 25 ns SO Fall Time VCC = 5 V, Cload = 40 pF − − 10 25 ns SCLK ↑ to SO 50% 10 − 20 50 ns SO Valid Time (Note 8) 8. Not tested in production. 9. Minimum high time of CSB between two successive SPI commands. http://onsemi.com 8 NCV7703B 4.0 6.0 VS = 13.2 V VCC = 0 V 3.5 VCC SLEEP CURRENT (mA) VS SLEEP CURRENT (mA) 7.0 5.0 4.0 3.0 2.0 1.0 0 −40 −20 VCC = 5.25 V 0 20 40 60 80 VCC = 5.25 V 3.0 2.5 2.0 1.5 1.0 0.5 0 −40 −20 100 120 140 160 TJ, TEMPERATURE (°C) 0 20 40 100 120 140 160 Figure 5. VCC Sleep Supply Current vs. Temperature Detailed SPI Timing 4 CSB 6 5 SCLK 1 80 TJ, TEMPERATURE (°C) Figure 4. VS Sleep Supply Current vs. Temperature 3 60 2 CSB SO 8 9 SI 12 SCLK 11 10 SO Figure 6. SPI Timing Waveforms http://onsemi.com 9 7 NCV7703B TYPICAL CHARACTERISTICS 140 120 1 oz Cu qJA (°C/W) 100 80 2 oz Cu 60 40 20 0 0 100 200 300 400 500 600 COPPER HEAT SPREADING AREA 700 800 (mm2) Figure 7. qJA vs. Copper Spreader Area, 14 Lead SON (fused leads) 1000 Cu Area = 100 mm2 1.0 oz R(t) (°C/W) 100 200 mm2 1.0 oz 10 300 mm2 1.0 oz 400 mm2 1.0 oz 500 mm2 1.0 oz 1 0.1 0.01 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100 1000 TIME (sec) Figure 8. Transient Thermal Response to a Single Pulse 1 oz Copper (Log−Log) 140 Cu Area = 100 mm2 1.0 oz R(t) (°C/W) 120 200 mm2 1.0 oz 100 300 mm2 1.0 oz 80 400 mm2 1.0 oz 500 mm2 1.0 oz 60 40 20 0 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 TIME (sec) Figure 9. Transient Thermal Response to a Single Pulse 1 oz Copper (Semi−Log) http://onsemi.com 10 10 100 1000 NCV7703B SPI Communication Frame Detection Standard 16−bit communication has been implemented to this IC to turn drivers on/off, and to report faults. (See Figure 11). The LSB (Least Significant Bit) is clocked in first. Input word integrity (SI) is evaluated by the use of a frame consistency check. The word frame length is compared to an h x 16 bit acceptable word length before the data is latched into the input register. This guarantees the proper word length has been imported and allows for daisy chain operation applications. The frame length detector is enabled with the CSB falling edge and the SCLK rising edge. SCLK must be low during the CSB rising edge. The fault register is cleared with a valid frame detection. Existing faults are re−latched after the fault filter time. Communication is Implemented as Follows: 1. CSB goes low to allow serial data transfer. 2. A 16 bit word is clocked (SCLK) into the SI (Serial Input) pin. 3. CSB goes high to transfer the clocked in information to the data registers. NOTE: SO is tristate when CSB is high. Frame detection starts after the CSB falling edge and the SCLK rising edge. Frame detection mode ends with CSB rising edge. CSB SCLK SI SRR OUTL1 OUTH1 OUTL2 OUTH2 OUTL3 OUTH3 Internal Counter 1 2 3 4 5 6 X X 7 8 9 X X X X 10 11 12 13 OCD 14 X OVLO 15 16 Valid 16 bits shown Figure 10. Frame Detection CSB SI SRR OUTL1 OUTH1 OUTL2 OUTH2 OUTL3 OUTH3 X X X X X X OCD X OVLO OUTL1 OUTH1 OUTL2 OUTH2 OUTL3 OUTH3 X X X X X X OLD ULD PSF SCLK SO TW Figure 11. SPI Communication Frame Format clocked into the SI pin of the device. Daisy chain communication between SPI compatible IC’s is possible by connection of the Serial Output pin (SO) to the input of the sequential IC (SI) (Reference the Daisy Chain Section). Table 1 defines the programming bits and diagnostic bits. Figure 11 displays the timing diagram associated with Table 1. Fault information is sequentially clocked out the SO pin of the NCV7703B as programming information is http://onsemi.com 11 NCV7703B Table 1. SPI BIT DESCRIPTION Input Data Output Data Bit Number Bit Description Bit Status Bit Number Bit Description Bit Status 15 Over Voltage Lock Out Control (OVLO) 0 = Disable 15 Power Supply Fail Signal (PSF for OVLO or UVLO) 0 = No Fault Under Load Detect Signal (ULD) 0 = No Fault 14 1 = Enable Not Used 14 1 = Fault 1 = Fault 13 Over Current Detection Shut Down Control (OCD) 13 0 = Disable Over Load Detect Signal (OLD) 1 = Enable 1 = Fault 12 Not Used 12 Not Used 11 Not Used 11 Not Used 10 Not Used 10 Not Used 9 Not Used 9 Not Used 8 Not Used 8 Not Used 7 Not Used 7 Not Used 6 OUTH3 6 OUTH3 0 = Off 1 = On 5 OUTL3 5 0 = Off OUTH2 OUTL3 4 0 = Off OUTL2 OUTH2 3 0 = Off OUTH1 OUTL2 2 OUTH1 1 = On OUTL1 0 = Off 0 Status Register Reset (SRR) 0 = No Reset 0 = Off 1 = On 0 = Off 1 0 = Off 1 = On 1 = On 2 0 = Off 1 = On 1 = On 3 0 = Off 1 = On 1 = On 4 0 = No Fault 0 = Off 1 = On 1 OUTL1 0 = Off 0 Thermal Warning (TW) 0 = Not in TW 1 = On 1 = On 1 = Reset 1 = In TW DETAILED OPERATING DESCRIPTION General Power Up/Down Control The NCV7703B Triple Half Bridge Driver provides drive capability for 3 Half−Bridge configurations. Each output drive is characterized for a 500 mA load and has a typical 1.4 A surge capability. Strict adherence to integrated circuit die temperature is necessary, with a maximum die temperature of 150°C. This may limit the number of drivers enabled at one time. Output drive control and fault reporting are handled via the SPI (Serial Peripheral Interface) port. An Enable function (EN) provides a low quiescent sleep current mode when the device is not being utilized. A pull down is provided on the EN, SI and SCLK inputs to ensure they default to a low state in the event of a severed input signal. A pull−up is provided on the CSB input disabling SPI communication in the event of an open CSB input. A feature incorporated in the IC is an under voltage lockout circuit that prevents the output drivers from turning on unintentionally. VCC and VS are monitored for undervoltage conditions supporting a smooth turn−on transition. All drivers are initialized in the off (high impedance) condition, and will remain off during a VCC or VS undervoltage condition. This allows power up sequencing of VCC, and VS up to the user. Once VCC is out of UVLO, SPI communication can begin regardless of the voltage on VS. However, drivers will remain off if VS is in an undervoltage condition. Hysteresis in the UVLO circuits results in glitch free operation during power up/down. http://onsemi.com 12 NCV7703B H−Bridge Driver Configuration The NCV7703B has the flexibility of controlling each half bridge driver independently. This allows for high side, low side and H−bridge control. H−bridge control provides forward, reverse, brake and high impedance states. been exceeded for a duration greater than 200 ms, regardless of the OLD input bit status. The OUTx output bit will report a “0” indicating which driver encountered the hard short. The OLD status bit will be set and will remain set until a new SRR input SPI command is executed. Overvoltage Clamping − Driving Inductive Loads Under−Load Detection (Table 3) Each output is internally clamped to ground and Vs by internal free wheeling diodes. The diodes have ratings that complement the FETs they protect. The under−load detection circuit monitors the current from each output driver. A minimum load current (this is the maximum open circuit detection threshold) is required when the drivers are turned on. If the under−load detection threshold has been detected for more than the under−load delay time, the ULD bit (output bit #14) will be set to a “1”. The under load bit is reset with SRR. Overcurrent Shutdown Threshold Detection (Table 2) The state of input bit 13 (OCD) selects driver reaction when reaching overcurrent shutdown threshold. With a “0” for input bit 13, the OLD status bit will be set to “1” when the level exceeds the overcurrent shutdown shut−down threshold and the driver will remain on. With a “1” for input bit 13, the output driver shuts off when the overcurrent shutdown threshold is exceeded and can only be turned back on via the SPI port with a SPI command that includes an SRR = 1. Note: high currents could cause a high rise in die temperature. Devices will not be allowed to turn on if the die temperature exceeds the thermal shutdown temperature. Overvoltage Shutdown (Table 4) Overvoltage lockout circuitry monitors the voltage on the VS pin. The response to an overvoltage condition is selected by SPI input bit 15. PSF output bit 15 is set when a VS overvoltage condition exists. If input bit 15 (OVLO) is set to “1”, all outputs will turn off during this overvoltage condition. Turn On/Off status is maintained in the logic circuitry, so that when proper input voltage level is reestablished, the programmed outputs will turn back on. The PSF output bit is reset with SRR. Current Limit Fault The current limit fault circuit will shut down the offending output driver when the Current Limit (Source or Sink) has Table 2. INPUT BIT 13, OVERCURRENT DETECTION SHUT DOWN CONTROL AND RESPONSE OLD Input Bit 13 Set Typical Load Current Condition Output Bit 13 OLD Status OUTx Status 0 IL ≤ 1.4 A 0 Unchanged 0 1.4 A < IL ≤ 3 A 1 (Need SRR to reset) Unchanged 0 IL ≥ 3 A, for 200 ms (typ) 1 (Need SRR to reset) OUTx Latched Off (Need SRR to reset) 1 IL ≤ 1.4 A 0 Unchanged 1 IL > 1.4 A, for 25 ms (typ) 1 (Need SRR to reset) OUTx Latched Off (Need SRR to reset) Table 3. INPUT BIT 14, UNDER LOAD DETECTION SHUT DOWN OUTx ULD Set Output Data Bit 14, Under Load Detect (ULD) Status OUTx Status 0 0 Unchanged 1 1 (Need SRR to reset) Unchanged Table 4. INPUT BIT 15, OVERVOLTAGE LOCK OUT (OVLO) SHUT DOWN OVLO Input Bit 15 VS OVLO Condition Output Data Bit 15 Power Supply Fail (PSF) Status OUTx Status 0 0 0 Unchanged 0 1 1 (Need SRR to reset) Unchanged 1 0 0 Unchanged 1 1 1 (Need SRR to reset) All Outputs Shut Off (Remain off until VS is out of OVLO) http://onsemi.com 13 NCV7703B Thermal Shutdown software polling of this bit will allow for load control and possible prevention of thermal shutdown conditions. Thermal warning information can be retrieved immediately without performing a complete SPI access cycle. Figure 12 below displays how this is accomplished. Bringing the CSB pin from a high to low condition immediately displays the information on the Output Data Bit 0, thermal warning, even in the absence of an SCLK signal. As the temperature of the NCV7703B changes from a condition from below the thermal warning threshold to above the thermal warning threshold, the state of the SO pin changes and this level is available immediately when the CSB goes low. A low on SO indicates there is no thermal warning, while a high indicates the IC is above the thermal warning threshold. This warning bit is reset by setting SRR to “1”. Three independent thermal shutdown circuits are featured (one common sensor for each HS and LS transistor pair). Each sensor has two temperature levels; Level 1, Thermal Warning sets the “TW” status bit to a 1 and would have to be reset with a command that includes the SRR after the IC cools to a temperature below Level 1. The output will remain on in this condition. If the IC temperature reaches Level 2, Over Temperature Shutdown, all drivers are latched off. It can be reset only after the part cools below the shutdown temperature, (including thermal hysteresis) with a turn−on command that includes the SRR set bit. The output data bit 0, Thermal Warning, will latch and remain set, even after cooling, and is reset by sending a SPI command to reset the status register (SRR, input 0 set to “1”). Since thermal warning precedes a thermal shutdown, CSB CSB SCLK* SCLK* SO SO TWH Tristate Level NTW Tristate Level Thermal Warning High No Thermal Warning *SCLK can be high or low in order to maintain the thermal information on SO. Toggling SCLK will cause other output bits to shift out. TWH = Thermal Warning High NTW = No Thermal Warning Figure 12. Access to Temperature Warning Information Applications Drawing Daisy Chain will be the Diagnostic Output Data. These are the bits representing the status of the IC and are detailed in the SPI Bit Description Table. Additional programming bits should be clocked in which follow the Diagnostic Output bits. Word length must be h x 16 due to the use of frame detection. The NCV7703B is capable of being setup in a daisy chain configuration with other similar devices which include additional NCV7703B devices as well as the NCV7708 Double Hex Driver. Particular attention should be focused on the fact that the first 16 bits which are clocked out of the SO pin when the CSB pin transitions from a high to a low http://onsemi.com 14 m icroprocessor NCV7703B CSB SCLK CSB SCLK CSB SCLK CSB SCLK NCV7703B NCV7703B NCV7708B NCV7708B SI SI SI SI SO SO SO SO Figure 13. Daisy Chain Operation Parallel Control A more efficient way to control multiple SPI compatible devices is to connect them in a parallel fashion and allow each device to be controlled in a multiplex mode. The diagram below shows a typical connection between the microprocessor or microcontroller and multiple SPI compatible devices. In a daisy chain configuration, the programming information for the last device in the serial string must first pass through all the previous devices. The parallel control setup eliminates that requirement, but at the cost of additional control pins from the microprocessor for each individual CSB pin for each controllable device. Serial data is only recognized by the device that is activated through its respective CSB pin. VS OUTx NCV7703B SI SCLK microprocessor SO CSB chip1 CSB chip2 CSB chip3 SI SCLK CSB OUT1 SO OUT2 OUT3 OUTx NCV7703B SI SCLK CSB OUT1 SO OUT2 OUT3 GND NCV7703B Figure 14. Parallel Control SI SCLK CSB OUT1 SO OUT2 OUT3 Figure 15. High−Side / Low−Side Application Drawing Any combination of H−bridge and high or low−side drivers can be designed in. This allows for flexibility in many systems. Additional Application Setup In addition to the cascaded H−Bridge application shown in Figure 1, the NCV7703B can also be used as a high−side driver or low−side driver (Figure 15). http://onsemi.com 15 NCV7703B PACKAGE DIMENSIONS SOIC−14 CASE 751A−03 ISSUE J NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. −A− 14 8 −B− P 7 PL 0.25 (0.010) M 7 1 G −T− 0.25 (0.010) M T B S A DIM A B C D F G J K M P R J M K D 14 PL F R X 45 _ C SEATING PLANE B M S SOLDERING FOOTPRINT* MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 7X 7.04 14X 1.52 1 14X 0.58 1.27 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 16 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCV7703B/D