SH276P Complementary Output Elektronische Bauelemente Hall Effect Latch Sink Driver IC RoHS Compliant Product Description The SH276P is an integrated Hall effect latched sensor with output pull-high resistor driver designed for electronic commutation of brushless DC motor applications. The device includes an on-chip Hall voltage generator for magnetic sensing, a comparator that amplifies the Hall voltage, and a Schmitt trigger to provide switching hysteresis for noise rejection, and complementary open-collector drivers for sinking large current loads. An internal bandgap regulator is used to provide temperature compensated supply voltage for internal circuits and allows a wide operating supply range. If a magnetic flux density larger than threshold Bop, DO is turned on (low) and DOB is turned off (high). The output state is held until a magnetic flux density reversal falls below Brp causing DO to be turned off and DOB turned on. SH276P is rated for operation over o o temperature range from -20 C to 85 C and voltage range from 3.5V to 20V. The devices are available in low cost die forms or rugged 4 pin SIP packages. Features REF. * High Output Sinking Capability Up To 300mA For Driving Large Load * Build In Protection Diode For Chip Reverse Power Connecting * On-Chip Hall Sensor IC With Two Different Sensitivity And Hysteresis Settings For SH276P * Lower Current Change Rate Reduces The Peak Output Voltage During Switching * Internal Bandgap Regulator Allows Temperature Compensated Operations And A Wide Operating Voltage Range * Package : SIP-4L Millimeter Min. Max. 1.803 REF. Millimeter Min. Max. D 5.105 5.359 E 3.531 3.785 14 16 A 1.295 A1 0.610 b 0.330 0.432 L b1 0.406 0.508 e 1.27REF Applications * Brushless DC Motor * Speed Measurement * Revolution Counting * Brushless DC Fan Pin Descriptions Name Vcc DO DOB Vss http://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A P/I/O P O O P Pin# 1 2 3 4 Description Positive Power supply Output Pin Output Pin Ground Any changing of specification will not be informed individual Page 1 of 5 SH276P Complementary Output Elektronische Bauelemente Hall Effect Latch Sink Driver IC Function Block Diagrams Absolute Parameter VCC Reverse VCC Polarity Voltage VRCC Magnetic Flux Density VCE Continuous Hold Unit 20 V -35 V Unlimited B Output OFF Voltage Output ON Current Value Symbol Supply Voltage V 35 300 IC mA 400 Operating Temperature Range TA -20~85 o Storage Temperature Range TS -65~150 o Package Power Dissipation PD 550 Max. Junction Temperature Tj 175 C C mW o C *Exceeding the absolute max. ratings may cause permanebt damage. Exposure to absolute max. rated conditions for extended periods may affect device reliability. Electrical Characteristics (Ta=+25 , Vcc=4.0V to 20V) Parameter Low Supply Voltage Supply Voltage Symbol Test Conditions Vce Vcc=3.5V, IL=100mA Vcc - Output Saturation Voltage Vce(sat) Vcc=14V, IL=300mA Output Leakage Current Supply Current Output Rise Time Output Falling Time Switch Time Differential http://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A ICex ICC Tr Tf t Vce=14V, Vcc=14V Vcc=20V, Output Open Vcc=14V, RL=820 , CL=20pf Vcc=14V, RL=820 , CL=20pf Vcc=14V, RL=820 , CL=20pf Min 3.5 Typ 0.4 - Max 20 Unit V V - 0.6 0.9 V - <1 18 3.0 0.3 3.0 10 25 10 1.5 10 uA mA us us us Any changing of specification will not be informed individual Page 2 of 5 SH276P Complementary Output Elektronische Bauelemente Hall Effect Latch Sink Driver IC Power dissipation vs. Environment Temperature Ta( ) 25 50 60 70 80 85 90 95 100 105 110 115 120 Pd(mW) 550 450 400 350 300 280 260 240 220 200 180 160 140 P d (m W ) P o w e r D is s ip a tio n C u rve 600 500 400 300 200 100 0 25 50 75 100 125 150 T a (ºC ) Magnetic Characteristics Characteristic BIN A Operate Point BIN B BIN C BIN A Release Point BIN B BIN C BIN A Hysteresis BIN B BIN C Symbol Bop Bop Bop Brp Brp Brp Bhys Bhys Bhys Ta=+25 Min Max 5 50 70 100 -50 -5 -70 -100 40 80 40 80 40 80 Ta=0 Min 5 -50 -70 -100 40 40 40 to 70 Max 50 70 100 -5 80 80 80 Unit Gauss Gauss Gauss Gauss Gauss Gauss Gauss Gauss Gauss Test Circuit 14V Vout1(DO) RL1 Vout2(DOB) RL2 RL1=RL2=820 Ohm CL1=CL2=20 pF h tp://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A CL1 CL2 Any changing of specification will not be informed individual Page 3 of 5 SH276P Complementary Output Elektronische Bauelemente Hall Effect Latch Sink Driver IC Hysteresis Characteristics Bin A RP 12 OFF 10 8 6 4 ON -200 -100 2 OP 0 100 DO Output Voltage in Volts Output Voltage in Volts DOB 200 OFF OP 10 8 6 4 RP -200 Magnetic Flux Density in Gauss 12 -100 2 ON 0 100 200 Magnetic Flux Density in Gauss Bin B 12 RP Output Voltage in Volts DO OFF 10 8 6 4 2 ON -200 -100 0 OP 100 200 Magnetic Flux Density in Gauss Output Voltage in Volts 12 OFF 10 8 6 4 2 ON -200 -100 0 OP 100 200 Magnetic Flux Density in Gauss http://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A OP 10 8 6 4 2 RP -100 0 ON 100 200 Magnetic Flux Density in Gauss Bin C DOB RP 12 OFF -200 DO Output Voltage in Volts Output Voltage in Volts DOB 12 OFF OP 10 8 6 4 2 RP -200 -100 0 ON 100 200 Magnetic Flux Density in Gauss Any changing of specification will not be informed individual Page 4 of 5 SH276P Complementary Output Elektronische Bauelemente Hall Effect Latch Sink Driver IC Application Circuit Double Coil 1) Output on current, Ic > 250mA 2) With FG output Remark: C1, C2: Capacitor 2.2 F~4.7 F (optional) Remark: C1: Capacitor 0.1 F~1 F R1: Resister 1K Package Information Active Area Depth Package Sensor Location 1.75mm Top View Marking Site 0.7mm 1.35mm Top View 1 2 3 4 Tolerance: +/- 0.05mm http://www.SeCoSGmbH.com/ 01-Jun-2002 Rev. A Any changing of specification will not be informed individual Page 5 of 5