30TPS16 High Voltage Series Vishay High Power Products Phase Control SCR, 20 A DESCRIPTION/FEATURES 2 (A) TO-247AC The 30TPS16 High Voltage Series of silicon controlled rectifiers are specifically designed for medium power switching and phase control applications. The glass passivation technology used has reliable operation up to 125 °C junction temperature. 1 (K) (G) 3 PRODUCT SUMMARY VT at 20 A < 1.3 V ITSM 300 A VRRM 1600 V Typical applications are in input rectification (soft start) and these products are designed to be used with Vishay HPP input diodes, switches and output rectifiers which are available in identical package outlines. This product has been designed and qualified for industrial level. MAJOR RATINGS AND CHARACTERISTICS PARAMETER IT(AV) TEST CONDITIONS Sinusoidal waveform VALUES UNITS 20 A IRMS 30 VRRM/VDRM 1600 V ITSM 300 A 1.3 V dV/dt 500 V/µs dI/dt 150 A/µs - 40 to 125 °C VRRM/VDRM, MAXIMUM REPETITIVE PEAK AND OFF-STATE VOLTAGE V VRSM, MAXIMUM NON-REPETITIVE PEAK REVERSE VOLTAGE V IRRM/IDRM AT 125 °C mA 1600 1700 10 VT 20 A, TJ = 25 °C TJ VOLTAGE RATINGS PART NUMBER 30TPS16 Document Number: 93925 Revision: 12-Aug-08 For technical questions, contact: [email protected] www.vishay.com 1 30TPS16 High Voltage Series Vishay High Power Products Phase Control SCR, 20 A ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Maximum average on-state current IT(AV) Maximum RMS on-state current IRMS Maximum peak, one-cycle, non-repetitive surge current ITSM VALUES 20 10 ms sine pulse, rated VRRM applied 250 10 ms sine pulse, no voltage reapplied 300 30 UNITS A 10 ms sine pulse, rated VRRM applied 310 10 ms sine pulse, no voltage reapplied 442 I2√t t = 0.1 to 10 ms, no voltage reapplied 4420 A2√s VTM 20 A, TJ = 25 °C 1.3 V 12 mΩ 1.0 V Maximum I2t for fusing I2 t Maximum I2√t for fusing Maximum on-state voltage drop On-state slope resistance TEST CONDITIONS TC = 95 °C, 180° conduction half sine wave rt Threshold voltage VT(TO) Maximum reverse and direct leakage current IRM/IDM TJ = 125 °C TJ = 25 °C TJ = 125 °C VR = Rated VRRM/VDRM A2s 0.5 10 Maximum holding current IH Anode supply = 6 V, resistive load, initial IT = 1 A 100 Maximum latching current IL Anode supply = 6 V, resistive load 200 mA Maximum rate of rise of off-state voltage dV/dt 500 V/µs Maximum rate of rise of turned-on current dI/dt 150 A/µs VALUES UNITS TRIGGERING PARAMETER SYMBOL Maximum peak gate power TEST CONDITIONS PGM 8.0 Maximum average gate power PG(AV) 2.0 Maximum peak positive gate current + IGM 1.5 A Maximum peak negative gate voltage - VGM 10 V Maximum required DC gate current to trigger Maximum required DC gate voltage to trigger IGT VGT Maximum DC gate voltage not to trigger VGD Maximum DC gate current not to trigger IGD Anode supply = 6 V, resistive load, TJ = - 10 °C 60 Anode supply = 6 V, resistive load, TJ = 25 °C 45 Anode supply = 6 V, resistive load, TJ = 125 °C 20 Anode supply = 6 V, resistive load, TJ = - 10 °C 2.5 Anode supply = 6 V, resistive load, TJ = 25 °C 2.0 Anode supply = 6 V, resistive load, TJ = 125 °C 1.0 TJ = 125 °C, VDRM = Rated value W mA V 0.25 2.0 mA VALUES UNITS SWITCHING PARAMETER SYMBOL Typical turn-on time tgt Typical reverse recovery time trr Typical turn-off time tq www.vishay.com 2 TEST CONDITIONS TJ = 25 °C TJ = 125 °C For technical questions, contact: [email protected] 0.9 4 µs 110 Document Number: 93925 Revision: 12-Aug-08 30TPS16 High Voltage Series Phase Control SCR, 20 A Vishay High Power Products THERMAL AND MECHANICAL SPECIFICATIONS PARAMETER SYMBOL Maximum junction and storage temperature range TJ, TStg Maximum thermal resistance, junction to case RthJC Maximum thermal resistance, junction to ambient RthJA Maximum thermal resistance, case to heatsink RthCS TEST CONDITIONS Marking device Document Number: 93925 Revision: 12-Aug-08 UNITS - 40 to 125 °C 0.8 DC operation °C/W 40 Mounting surface, smooth and greased Approximate weight Mounting torque VALUES 0.2 6 g 0.21 oz. minimum 6 (5) maximum 12 (10) kgf · cm (lbf · in) Case style TO-247AC (JEDEC) For technical questions, contact: [email protected] 30TPS16 www.vishay.com 3 30TPS16 High Voltage Series 30TPS.. Series R thJC (DC) = 0.8 °C/ W 120 Conduction Angle 110 30° 60° 90° 100 120° 180° 90 0 5 10 15 20 25 Maximum Average On-state Power Loss (W) 130 DC 180° 120° 90° 60° 30° 60 40 RMS Limit Conduction Period 20 30TPS.. Series TJ = 125°C 0 0 10 20 30 40 50 Average On-state Current (A) Fig. 1 - Current Rating Characteristics Fig. 4 - On-State Power Loss Characteristics 130 30TPS.. Series RthJC (DC) = 0.8 °C/ W 120 110 Conduction Period 100 30° 60° 90 90° 120° 180° DC 80 0 5 10 15 20 25 30 35 180° 120° 90° 60° 30° RMS Limit 30 20 Conduction Angle 30TPS.. Series TJ= 125°C 10 0 0 5 10 15 20 25 220 200 180 160 140 30TPS.. Series 120 10 100 30 Fig. 5 - Maximum Non-Repetitive Surge Current Peak Half Sine Wave On-state Current (A) 60 40 At Any Rated Load Condition And With Rated V RRM Applied Following Surge. Initial TJ = 125°C @60 Hz 0.0083 s 240 @50 Hz 0.0100 s 260 1 Fig. 2 - Current Rating Characteristics 50 280 Numb er Of Equa l Amplitude Ha lf Cyc le Current Pulses (N) Average On-state Current (A) Maximum Average On-state Power Loss (W) 80 Average On-state Current (A) Peak Half Sine Wave On-state Current (A) Maximum Allowable Case Temperature (°C) Maximum Allowable Case Temperature (°C) Vishay High Power Products Phase Control SCR, 20 A 300 280 260 240 Maximum Non Repetitive Surge Current Versus Pulse Tra in Duration. Control Of Conduc tion May Not Be Ma intained. Initial TJ= 125°C No Voltage Reapplied Rated VRRMReapplied 220 200 180 160 140 30TPS.. Series 120 0.01 0.1 1 Average On-state Current (A) Pulse Train Duration (s) Fig. 3 - On-State Power Loss Characteristics Fig. 6 - Maximum Non-Repetitive Surge Current www.vishay.com 4 For technical questions, contact: [email protected] Document Number: 93925 Revision: 12-Aug-08 30TPS16 High Voltage Series Phase Control SCR, 20 A Vishay High Power Products Instantaneous On-state Current (A) 1000 TJ= 25°C TJ= 125°C 100 10 30TPS.. Series 1 0 1 2 3 4 5 6 7 Instantaneous On-state Voltage (V) Transient Thermal Impedance Z thJC (°C/ W) Fig. 7 - On-State Voltage Drop Characteristics 1 Steady State Value (DC Operation) D = 0.50 D = 0.33 D = 0.25 D = 0.17 0.1 D = 0.08 Single Pulse 30TPS.. Series 0.01 0.0001 0.001 0.01 0.1 1 Square Wave Pulse Duration (s) Fig. 8 - Thermal Impedance ZthJC Characteristics Rec tangular gate p ulse a )Rec ommend ed loa d line for rated di/ dt: 10 V, 20 ohms tr = 0.5 µs, tp >= 6 µs b)Recommend ed load line for <= 30% rated di/ dt: 10 V, 65 ohms 10 tr = 1 µs, tp >= 6 µs (1) PGM = 40 W, tp = 1 ms (2) PGM = 20 W, tp = 2 ms (3) PGM = 8 W, tp = 5 ms (4) PGM = 4 W, tp = 10 ms (a ) (b ) VGD IGD 0.1 0.001 TJ = -10 °C TJ = 125 °C 1 TJ = 25 °C Instantaneous Gate Voltage (V) 100 (4) 0.1 (2) (1) Frequency Limited by PG(AV) 30TPS.. Series 0.01 (3) 1 10 100 Instantaneous Gate Current (A) Fig. 9 - Gate Characteristics Document Number: 93925 Revision: 12-Aug-08 For technical questions, contact: [email protected] www.vishay.com 5 30TPS16 High Voltage Series Vishay High Power Products Phase Control SCR, 20 A ORDERING INFORMATION TABLE Device code 30 T P S 16 - 1 2 3 4 5 6 1 - Current rating (30 = 30 A) 2 - Circuit configuration: T = Thyristor 3 - Package: P = TO-247 4 - Type of silicon: S = Standard recovery rectifier 5 - 6 - Voltage rating (16 = 1600 V) None = Standard production PbF = Lead (Pb)-free LINKS TO RELATED DOCUMENTS Dimensions http://www.vishay.com/doc?95223 Part marking information http://www.vishay.com/doc?95226 www.vishay.com 6 For technical questions, contact: [email protected] Document Number: 93925 Revision: 12-Aug-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1