40TPS16 High Voltage Series Vishay High Power Products Phase Control SCR, 35 A DESCRIPTION/FEATURES 2 (A) TO-247AC The 40TPS16 High Voltage Series of silicon controlled rectifiers are specifically designed for medium power switching and phase control applications. The glass passivation technology used has reliable operation up to 125 °C junction temperature. Low Igt parts available. 1 (K) (G) 3 PRODUCT SUMMARY VT at 40 A < 1.45 V ITSM 500 A VRRM 1600 V Typical applications are in input rectification (soft start) and these products are designed to be used with Vishay HPP input diodes, switches and output rectifiers which are available in identical package outlines. This product has been designed and qualified for industrial level. MAJOR RATINGS AND CHARACTERISTICS PARAMETER IT(AV) TEST CONDITIONS Sinusoidal waveform UNITS 35 A IRMS VRRM/VDRM VALUES 55 Range (1) 1600 V 500 A 1.45 V dV/dt 1000 V/µs dI/dt 100 A/µs - 40 to 125 °C VRRM/VDRM, MAXIMUM REPETITIVE PEAK AND OFF-STATE VOLTAGE V VRSM, MAXIMUM NON-REPETITIVE PEAK REVERSE VOLTAGE V IRRM/IDRM AT 125 °C mA 1600 1700 10 ITSM VT 40 A, TJ = 25 °C TJ Note (1) Contact factory VOLTAGE RATINGS PART NUMBER 40TPS16 Document Number: 93709 Revision: 12-Sep-08 For technical questions, contact: [email protected] www.vishay.com 1 40TPS16 High Voltage Series Vishay High Power Products Phase Control SCR, 35 A ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Maximum average on-state current IT(AV) Maximum continuous RMS on-state current as AC switch TEST CONDITIONS VALUES TC = 79 °C, 180° conduction half sine wave 55 IT(RMS) Maximum peak, one-cycle non-repetitive surge current ITSM Maximum I2t for fusing I2t Maximum I2√t for fusing I2√t Low level value of threshold voltage VT(TO)1 High level value of threshold voltage VT(TO)2 Low level value of on-state slope resistance rt1 High level value of on-state slope resistance rt2 10 ms sine pulse, rated VRRM applied t = 0.1 to 10 ms, no voltage reapplied 12 500 1.02 1.23 TJ = 125 °C 9.74 7.50 110 A, TJ = 25 °C Maximum rate of rise of turned-on current dI/dt TJ = 25 °C IH Maximum latching current IL Maximum reverse and direct leakage current Maximum rate of rise of off-state voltage IRRM/IDRM 1250 1760 VTM Maximum holding current 600 Initial TJ = TJ maximum 10 ms sine pulse, no voltage reapplied Maximum peak on-state voltage A 500 10 ms sine pulse, no voltage reapplied 10 ms sine pulse, rated VRRM applied UNITS 35 A2s A2√s V mΩ 1.85 V 100 A/µs 150 300 TJ = 25 °C TJ = 125 °C 0.5 VR = Rated VRRM/VDRM mA 10 dV/dt TJ = TJ maximum, linear to 80 % VDRM, Rg-k = Open 1000 V/µs SYMBOL TEST CONDITIONS VALUES UNITS TRIGGERING PARAMETER Maximum peak gate power Maximum average gate power Maximum peak gate current Maximum peak negative gate voltage PGM 10 PG(AV) 2.5 IGM 2.5 - VGM 10 TJ = - 40 °C Maximum required DC gate voltage to trigger VGT Maximum required DC gate current to trigger IGT Maximum DC gate voltage not to trigger VGD Maximum DC gate current not to trigger IGD TJ = 25 °C 4.0 Anode supply = 6 V resistive load TJ = 125 °C 1.7 TJ = - 40 °C 270 TJ = 25 °C 150 TJ = 125 °C 80 TJ = 25 °C, for 40TPS08A www.vishay.com 2 2.5 TJ = 125 °C, VDRM = Rated value For technical questions, contact: [email protected] W A V mA 40 0.25 V 6 mA Document Number: 93709 Revision: 12-Sep-08 40TPS16 High Voltage Series Phase Control SCR, 35 A Vishay High Power Products THERMAL AND MECHANICAL SPECIFICATIONS PARAMETER SYMBOL Maximum junction and storage temperature range TJ, TStg Maximum thermal resistance, junction to case RthJC Maximum thermal resistance, junction to ambient RthJA Maximum thermal resistance, case to heatsink RthCS TEST CONDITIONS DC operation Marking device Document Number: 93709 Revision: 12-Sep-08 UNITS - 40 to 125 °C 0.6 °C/W 40 Mounting surface, smooth and greased Approximate weight Mounting torque VALUES 0.2 6 g 0.21 oz. minimum 6 (5) maximum 12 (10) kgf · cm (lbf · in) Case style TO-247AC For technical questions, contact: [email protected] 40TPS16 www.vishay.com 3 40TPS16 High Voltage Series Maximum Averag e On-state Power Loss (W) 130 40TPS.. Series R thJC (DC) = 0.6 °C/ W 120 110 Conduction Angle 100 30° 60° 90° 90 120° 180° 80 70 0 10 20 30 DC 180° 120° 90° 60° 30° 70 60 50 40 RMSLimit 30 Conduction Period 20 40TPS.. Series TJ = 125 °C 10 0 0 10 20 30 40 50 60 Average On-state Current (A) Avera ge On-sta te Current (A) Fig. 1 - Current Rating Characteristics Fig. 4 - On-State Power Loss Characteristics 130 40TPS.. Series RthJC (DC) = 0.6 °C/ W 120 110 Conduction Period 100 30° 90 60° 90° 120° 180° 80 DC 70 0 10 20 30 40 50 60 RMS Limit 30 20 Conduction Angle 40TPS.. Series TJ= 125°C 10 0 0 5 10 15 20 25 30 35 40 Peak Half Sine Wa ve On-state Current (A) 40 500 450 400 350 300 40TPS.. Series 250 10 100 Fig. 5 - Maximum Non-Repetitive Surge Current 60 50 At Any Ra ted Load Condition And With Rated V RRM Ap plied Following Surge. Initia l TJ= 125°C @60 Hz 0.0083 s @50 Hz 0.0100 s 1 Fig. 2 - Current Rating Characteristics 180° 120° 90° 60° 30° 550 Number Of Equal Amplitude Half Cycle Current Pulses (N) Average On-state Current (A) Maximum Avera g e On-state Power Loss (W) 80 40 Peak Half Sine Wave On-state Current (A) Maximum Allowable Case Temperature (°C) Maximum Allowable Case Temperature (°C) Vishay High Power Products Phase Control SCR, 35 A 600 Ma ximum Non Rep etitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. Initial TJ = 125°C No Voltage Reap p lied Rated VRRM Reap p lied 550 500 450 400 350 300 40TPS.. Series 250 0.01 0.1 1 Avera ge On-sta te Current (A) Pulse Tra in Duration (s) Fig. 3 - On-State Power Loss Characteristics Fig. 6 - Maximum Non-Repetitive Surge Current www.vishay.com 4 For technical questions, contact: [email protected] Document Number: 93709 Revision: 12-Sep-08 40TPS16 High Voltage Series Phase Control SCR, 35 A Vishay High Power Products Instanta neous On-sta te Current (A) 100 10 TJ= 25°C TJ= 125°C 40TPS.. Series 1 0.5 1 1.5 2 Instantaneous On-state Voltag e (V) Fig. 7 - On-State Voltage Drop Characteristics 10 Rec tangular gate pulse a)Rec ommended load line for rated di/ dt: 20 V, 30 ohms tr = 0.5 µs, tp >= 6 µs b)Rec ommended load line for <= 30% rated di/ dt: 20 V, 65 ohms tr = 1 µs, tp >= 6 µs (1) PGM = 100 W, tp = 500 µs (2) PGM = 50 W, tp = 1 ms (3) PGM = 20 W, tp = 25 ms (4) PGM = 10 W, tp = 5 ms (a) (b) 1 TJ = -40 °C TJ = 125 °C TJ = 25 °C Instantaneous Gate Voltage (V) 100 (4) (3) (2) (1) VGD IGD 0.1 0.001 40TPS.. 0.01 0.1 Frequenc y Limited by PG(AV) 1 10 100 1000 Instantaneous Gate Current (A) Transient Thermal Impeda nc e Z thJC (°C/W) Fig. 8 - Gate Characteristics 1 0.1 Steady State Value (DC Opera tion) D = 0.50 D = 0.33 D = 0.25 D = 0.17 D = 0.08 Single Pulse 40TPS.. Series 0.01 0.0001 0.001 0.01 0.1 1 Square Wave Pulse Duration (s) Fig. 9 - Thermal Impedance ZthJC Characteristics Document Number: 93709 Revision: 12-Sep-08 For technical questions, contact: [email protected] www.vishay.com 5 40TPS16 High Voltage Series Vishay High Power Products Phase Control SCR, 35 A ORDERING INFORMATION TABLE Device code 40 T P S 16 - 1 2 3 4 5 6 1 - 2 - Current rating (40 = 40 A) Circuit configuration: T = Thyristor 3 - 4 - 5 - 6 - Package: P = TO-247 Type of silicon: S = Standard recovery rectifier Voltage code x 100 = VRRM (16 = 1600 V - contact factory) None = Standard production PbF = Lead (Pb)-free LINKS TO RELATED DOCUMENTS Dimensions http://www.vishay.com/doc?95024 Part marking information http://www.vishay.com/doc?95226 www.vishay.com 6 For technical questions, contact: [email protected] Document Number: 93709 Revision: 12-Sep-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1