3.0mmx1.0 mm RIGHT ANGLE SMD CHIP LED LAMP APA3010SYC Features SUPER BRIGHT YELLOW z3.0mmx1.0mm RIGHT ANGLE SMT LED, 2.0mm Description THICKNESS. (on GaAs substrate) light emitting diode chip. zLOW POWER CONSUMPTION. The Super Bright Yellow device is made with DH InGaAlP zWIDE VIEWING ANGLE. zIDEAL FOR BACK LIGHT AND INDICATOR. zVARIOUS COLORS AND LENS TYPES AVAILABLE. zPACKAGE : 2000PCS / REEL. zRoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAB1176 REV NO: V.8 DATE: JUN/29/2005 PAGE: 1 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.H.CHEN ERP: 1203000646 Selection Guide Part No. Dice APA3010SYC Iv (mcd) @ 20mA Lens Type SUPER BRIGHT YELLOW (InGaAlP) WATER CLEAR Viewing Angle Min. Typ. 2 θ 1/2 36 120 120° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Yellow λD Dominant Wavelength ∆λ1/2 Max. Units Test Conditions 590 nm IF=20mA Super Bright Yellow 588 nm IF=20mA Spectral Line Half-width Super Bright Yellow 28 nm IF=20mA C Capacitance Super Bright Yellow 25 pF VF=0V;f=1MHz VF Forward Voltage Super Bright Yellow 2.0 2.5 V IF=20mA IR Reverse Current Super Bright Yellow 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Super Bright Yellow Units Power dissipation 125 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage -40°C To +85°C Operating/Storage Temperature Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAB1176 REV NO: V.8 DATE: JUN/29/2005 PAGE: 2 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.H.CHEN ERP: 1203000646 Super Bright Yellow APA3010SYC SPEC NO: DSAB1176 REV NO: V.8 DATE: JUN/29/2005 PAGE: 3 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.H.CHEN ERP: 1203000646 APA3010SYC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAB1176 REV NO: V.8 DATE: JUN/29/2005 PAGE: 4 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.H.CHEN ERP: 1203000646 PACKING & LABEL SPECIFICATIONS APA3010SYC SPEC NO: DSAB1176 REV NO: V.8 DATE: JUN/29/2005 PAGE: 5 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.H.CHEN ERP: 1203000646