19-1741 Rev 0; 10/00 Digital Camera Step-Up Slave DC-DC Controller Features The MAX1801 step-up slave DC-DC controller is used with either the MAX1800 (step-up) or the MAX1802 (stepdown) master DC-DC converter to provide a complete power-supply solution for digital still and digital video cameras. By using the master converter’s reference voltage and oscillator, the size and the cost of the slave controller are reduced and all converters are guaranteed to switch at the same frequency. ♦ Provides Simple Expandability for the MAX1800 and MAX1802 Master Converters ♦ Operates in Step-Up, SEPIC, and Flyback Topologies ♦ 100kHz to 1MHz Adjustable Operating Frequency The MAX1801 drives an external N-channel MOSFET and can be used in step-up, single-ended primary inductance converter (SEPIC), and flyback topologies. If extra supplies are required for a new design, slave controllers can be added to an existing master circuit with minimal redesign, saving both cost and time. The MAX1801 features a built-in soft-start, short-circuit protection, and an adjustable duty-cycle limit. ♦ Short-Circuit Protection ♦ Duty-Cycle Limit Adjustable from 40% to 90% ♦ Soft-Start ♦ 0.01µA Supply Current in Shutdown Mode ♦ Tiny 8-Pin SOT23 Package Ordering Information The MAX1801 is available in a space-saving 8-pin SOT23 package. Separate evaluation kits combining the MAX1800/MAX1801 (MAX1800EVKIT) and MAX1802/ MAX1801 (MAX1802EVKIT) are available to expedite designs. ________________________Applications Digital Still Cameras Internet Access Tablets Digital Video Cameras PDAs Portable DVD Players Hand-Held Devices PART TEMP. RANGE PIN-PACKAGE MAX1801EKA-T -40°C to +85°C 8 SOT23-8 Pin Configuration appears at end of data sheet. Typical Operating Circuit BATTERY 0.7V TO VOUT VOUT MAX1800 1.25V MAX1801 REF DL OSC FB OR MAX1802 2.2V TO 5.5V IN COMP DCON GND ________________________________________________________________ Maxim Integrated Products 1 For price, delivery, and to place orders, please contact Maxim Distribution at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. MAX1801 General Description MAX1801 Digital Camera Step-Up Slave DC-DC Controller ABSOLUTE MAXIMUM RATINGS IN, DCON, REF, OSC, FB to GND.........................-0.3V to +6.0V DL, COMP to GND.......................................-0.3V to (VIN + 0.3V) Continuous Power Dissipation (TA = +70°C) 8-Pin SOT23 (derate 6mW/°C above+70°C)................480mW Operating Temperature Range ...........................-40°C to +85°C Junction Temperature ......................................................+150°C Storage Temperature Range. ............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (Circuit of Figure 1, VIN = +3.3V, VDCON = +1.25V, VREF = +1.25V, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1) PARAMETER CONDITIONS MIN TYP MAX UNITS 5.5 V V GENERAL VIN Supply Voltage Operating Range VIN Undervoltage Lockout Threshold 2.7 VIN rising REF Input Range REF Undervoltage Lockout Threshold VREF rising Shutdown Supply Current VIN = 5.5V, VDCON = 0, VREF = 0 Sleep-Mode Supply Current VIN = 3.3V, VDCON = 0, VREF = 1.25V Quiescent Supply Current VOSC = 0, VFB = 0 2.2 2.35 2.5 1.19 1.25 1.31 V 0.9 1.0 1.1 V 0.01 1 µA 5 10 µA 124 300 µA OSCILLATOR INPUT OSC Input Leakage Current VOSC = 1.5V 100 OSC Clock Low Trip Level 0.20 1.00 0.575 OSC Clock High Trip Level VDCON = 0.625V 1 µA 1000 kHz 0.25 0.30 V 1.05 1.10 0.625 0.675 0.04 Oscillator Frequency Range V Maximum Duty Cycle Adjustment Range (Note 2) fOSC = 100kHz Maximum Duty Cycle (Note 2) VDCON = 0.625V, fOSC = 100kHz 50 % Default Maximum Duty Cycle (Note 2) VDCON = 1.25V, fOSC = 100kHz 84 % 40 90 % INPUTS/OUTPUTS DCON Input Leakage Current VDCON = 5.5V DCON Input Sleep-Mode Threshold IIN ≤ 10µA REF Input Current 9 100 nA 0.4 0.45 V VDCON = 0 0.5 1.1 VDCON = VREF 3.3 10 VDCON = VREF , during soft-start 13 30 1.238 1.250 1.263 V 70 100 160 µS 0.35 µA ERROR AMPLIFIER FB Regulation Voltage FB to COMP Transconductance -5µA < ICOMP < 5µA FB to COMP Maximum Voltage Gain FB Input Leakage Current 2 2000 VFB = 1.35V 30 _______________________________________________________________________________________ V/V 100 nA Digital Camera Step-Up Slave DC-DC Controller (Circuit of Figure 1, VIN = +3.3V, VDCON = +1.25V, VREF = +1.25V, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1) PARAMETER CONDITIONS MIN TYP MAX UNITS DL Driver Resistance 2.5 5 Ω DL Drive Current 0.5 A 1024 OSC cycles 1024 OSC cycles DRIVER SOFT-START Soft-Start Interval SHORT-CIRCUIT PROTECTION Fault Interval ELECTRICAL CHARACTERISTICS (Circuit of Figure 1, VIN = +3.3V, VDCON = +1.25V, VREF = +1.25V, TA = -40°C to +85°C, unless otherwise noted.) (Note 1) PARAMETER CONDITIONS MIN TYP MAX UNITS 2.7 5.5 V 2.15 2.55 V 1.19 1.31 V 0.85 1.15 V GENERAL VIN Supply Voltage Operating Range VIN Undervoltage Lockout Threshold VIN rising REF Input Range REF Undervoltage Lockout Threshold VREF rising Shutdown Supply Current VIN = 5.5V, VDCON = 0, VREF = 0 1 µA Sleep-Mode Supply Current VIN = 3.3V, VDCON = 0, VREF = 1.25V 10 µA Quiescent Supply Current VOSC = 0, VFB = 0 300 µA OSCILLATOR INPUT 1 µA Oscillator Frequency Range 100 1000 kHz OSC Clock Low Trip Level 0.20 0.30 V 1.00 1.10 0.575 0.675 40 90 % 100 nA 0.45 V OSC Input Leakage Current OSC Clock High Trip Level Maximum Duty Cycle Adjustment Range (Note 2) VOSC = 1.5V VDCON = 0.625V fOSC = 100kHz V INPUTS/OUTPUTS DCON Input Leakage Current VDCON = 5.5V DCON Input Sleep-Mode Threshold IIN ≤ 10µA REF Input Current 0.35 VDCON = 0 1.1 VDCON = VREF 10 VDCON = VREF , during soft-start 30 µA _______________________________________________________________________________________ 3 MAX1801 ELECTRICAL CHARACTERISTICS (continued) ELECTRICAL CHARACTERISTICS (continued) (Circuit of Figure 1, VIN = +3.3V, VDCON = +1.25V, VREF = +1.25V, TA = -40°C to +85°C, unless otherwise noted.) (Note 1) PARAMETER CONDITIONS MIN TYP MAX UNITS 1.263 V ERROR AMPLIFIER FB Regulation Voltage 1.238 FB to COMP Transconductance -5µA < ICOMP < 5µA FB Input Leakage Current VFB = 1.35V 70 160 µS 100 nA 5 Ω DRIVER DL Driver Resistance Note 1: All devices are 100% tested at TA = +25°C. All limits over the temperature range are guaranteed by design. Note 2: Oscillator signal is generated by the MAX1800 or MAX1802. Typical Operating Characteristics (Circuit of Figure 1, TA = +25°C, unless otherwise noted.) 80 VOUT = +7V 80 VOUT = +18V V OUT = +12V 50 40 70 60 VOUT = +18V 50 VOUT = +12V 40 40 30 20 20 20 10 10 10 0 0 100 LOAD CURRENT (mA) 1000 VOUT = +12V 50 30 10 VOUT = +18V 60 30 1 VOUT = +7V 80 EFFICIENCY (%) 60 VBATT = +3.6V 90 70 EFFICIENCY (%) 70 4 VBATT = +2.4V 90 EFFICIENCY vs. LOAD CURRENT 100 MAX1801 toc03 VOUT = +7V MAX1801 toc01 VBATT = +1.5V 90 EFFICIENCY vs. LOAD CURRENT 100 MAX1801 toc02 EFFICIENCY vs. LOAD CURRENT 100 EFFICIENCY (%) MAX1801 Digital Camera Step-Up Slave DC-DC Controller 0 1 10 100 LOAD CURRENT (mA) 1000 1 10 100 LOAD CURRENT (mA) _______________________________________________________________________________________ 1000 Digital Camera Step-Up Slave DC-DC Controller DEFAULT MAXIMUM DUTY CYCLE vs. FREQUENCY MAXIMUM DUTY CYCLE vs. VDCON 80 60 40 20 MAX1801 toc05 100 MAX1801 toc04 fOSC = 500kHz DEFAULT MAXIMUM DUTY CYCLE (%) MAXIMUM DUTY CYCLE (%) 100 80 60 COSC = 470pF 40 20 0 0 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 0 1.2 200 SLEEP-MODE CURRENT vs. INPUT VOLTAGE 800 1000 SHUTDOWN CURRENT (µA) 8 6 4 2 MAX1801 toc07 10 MAX1801toc06 1 0.1 0.01 0 0.001 3.0 3.5 4.0 4.5 5.0 5.5 0 0.5 1.0 1.5 INPUT VOLTAGE (V) REFERENCE VOLTAGE (V) REFERENCE INPUT CURRENT vs. TEMPERATURE FB TO COMP SMALL-SIGNAL OPEN-LOOP FREQUENCY RESPONSE MAX1801 toc08 3.40 3.35 3.30 3.25 60 MAX1801 toc09 2.5 SMALL-SIGNAL RESPONSE (dB) SLEEP-MODE CURRENT (µA) 600 SHUTDOWN CURRENT vs. REFERENCE VOLTAGE 10 REFERENCE CURRENT (µA) 400 FREQUENCY (kHz) VDCON (V) 50 40 30 20 10 0 3.20 -40 -20 0 20 40 TEMPERATURE (°C) 60 80 1 10 100 1000 10,000 FREQUENCY (kHz) _______________________________________________________________________________________ 5 MAX1801 Typical Operating Characteristics (continued) (Circuit of Figure 1, TA = +25°C, unless otherwise noted.) MAX1801 Digital Camera Step-Up Slave DC-DC Controller Typical Operating Characteristics (continued) (Circuit of Figure 1, TA = +25°C, unless otherwise noted.) LOAD TRANSIENT RESPONSE STARTUP RESPONSE MAX1801 toc11 MAX1801 toc10 VDCON 5V/div OV VOUT 100mV/div (AC-COUPLED) VOUT 2V/div OV 500mA IIN 0.5A/div ILOAD 0.2A/div 100mA OA VIN = =+2.4V, VOUT = +5V, fOSC = 500kHz OA 400µs/div 1ms/div Pin Description 6 PIN NAME FUNCTION 1 OSC Oscillator Input. Connect OSC to OSC of the MAX1800 or MAX1802. The oscillator frequency must be between 100kHz and 1MHz. 2 GND Ground 3 REF 1.25V Reference Input. Connect REF to REF of the MAX1800 or MAX1802. REF must be above 1V for the controller to turn on. Bypass REF to GND with a 0.1µF or greater capacitor. 4 DCON Maximum Duty-Cycle Control Input. Connect to REF or IN to set the default maximum duty cycle. Connect a resistive voltage-divider from REF to DCON to set the maximum duty cycle between 40% and 90%. Pull DCON below 0.35V to turn the controller off. 5 COMP Controller Compensation. Output of transconductance error amplifier. Connect a series resistor and capacitor to GND to compensate the control loop. See Compensation Design. 6 FB Controller Feedback Input. Connect a feedback resistive voltage-divider from the output to FB to set the output voltage. Regulation voltage is VREF (1.25V). 7 IN IC Supply Bias Input. Bypass IN to GND with a 0.1µF or greater ceramic capacitor. Supply range is 2.7V to 5.5V. 8 DL External MOSFET Gate Drive Output. DL swings between IN and GND with typical 500mA drive current. Connect DL to the gate of the external switching N-channel MOSFET. _______________________________________________________________________________________ Digital Camera Step-Up Slave DC-DC Controller MAX1801 CIN 10µF VBATT L 2.2µH MBRO520L VOUT COUT 47µF FDN337N MAX1800 3.3V MAX1801 IN DL OSC FB REF COMP OR R1 1.25V MAX1802 R3 RC 10k R2 DCON GND CC 1000pF R4 Figure 1. Typical Application Circuit Detailed Description Master-Slave Configuration The MAX1801 is a step-up slave DC-DC controller that obtains its input power, voltage reference, and oscillator signal directly from a MAX1800 or MAX1802 master DC-DC converter (Figure 1). The master-slave configuration reduces system cost by eliminating redundant circuitry and controls the harmonic content of noise by synchronizing converter switching. Step-Up DC-DC Controller The MAX1801 controller operates in a low-noise fixedfrequency PWM mode, with output power limited by the external components. The controller regulates the output voltage by modulating the pulse width of the drive signal for an external N-channel MOSFET switch. The user-adjusted switching frequency is constant (100kHz to 1MHz) and set by the master converter. Figure 2 shows a block diagram of the MAX1801 PWM controller. A sawtooth oscillator signal from the master converter (at OSC) governs the internal timing. At the beginning of each cycle, DL goes high to turn on the external MOSFET switch. The MOSFET switch turns off when the internally level-shifted sawtooth waveform voltage rises above the voltage at COMP or when the maximum duty cycle is exceeded. The switch remains off until the beginning of the next cycle. An internal transconductance amplifier establishes an integrated error voltage at COMP, increasing the loop gain for improved regulation accuracy and compensation control. Reference The MAX1801 requires a 1.25V reference voltage that is obtained from the MAX1800 or the MAX1802. REF typically sinks 0.5µA in shutdown mode, 3µA in active mode, and up to 30µA during startup. If multiple MAX1801 controllers are turned on simultaneously, ensure that the master voltage reference can provide sufficient current, or buffer the reference with an appropriate unity-gain amplifier. _______________________________________________________________________________________ 7 MAX1801 Digital Camera Step-Up Slave DC-DC Controller FB COMP R Q DL LEVEL SHIFT REFI SOFTSTART* REF S DCON CLK OSC *SOFT-START RAMPS REFI FROM 0 TO VREF IN 1024 CLK CYCLES. FAULT PROTECTION ENABLE 0.4V POWER-ON 1.1V IN 2.35V IC POWER Figure 2. PWM Controller Block Diagram Oscillator The MAX1801 requires a 0 to 1.25V sawtooth oscillator signal that is obtained from the MAX1800 or the MAX1802 (at OSC). The 100kHz to 1MHz oscillator signal sets the converter switching frequency, and it is used to control pulse-width modulation and maximum duty cycle. Maximum Duty Cycle The MAX1801 uses the master-generated oscillator signal at OSC, the voltage at DCON, and an internal comparator to limit its maximum switching duty cycle (see Setting the Maximum Duty Cycle). Limiting the duty cycle can prevent saturation in some magnetic compo8 nents. A low maximum duty cycle can also force the converter to operate in discontinuous current mode, simplifying design stability at the cost of a slight reduction in efficiency. Soft-Start The MAX1801 features a soft-start function that limits inrush current and prevents excessive battery loading at startup by ramping the output voltage to the regulation voltage. This is achieved by increasing the internal reference to the transconductance amplifier from 0 to the 1.25V reference voltage over 1024 oscillator cycles when initial power is applied or when the part is taken out of shutdown or sleep mode. _______________________________________________________________________________________ Digital Camera Step-Up Slave DC-DC Controller VOSC (V) DMAX = t2 t1 + t2 1.25 VDCON 0.25 0 Setting the Output Voltages Set the MAX1801 output voltage by connecting a resistive voltage-divider from the output to FB as shown in Figure 1. The FB input bias current is less than 100nA, so choose R2 to be 100kΩ to minimize the effect of input bias current at FB. Choose R1 according to the relation: CLK t1 t2 Figure 3. Setting the Maximum Duty Cycle Shutdown Set VDCON less than 0.35V to place the MAX1801 in sleep mode, which drops the supply current to 5µA. To reduce the supply current to 10nA, place the MAX1801 in shutdown by setting VREF below 0.4V. The MAX1801 enters soft-start when both VDCON and VREF are at normal levels. Short-Circuit Protection The MAX1801 has a fault protection feature that prevents damage to transformer-coupled or SEPIC circuits due to an output short circuit. If the output voltage drops out of regulation, the voltage at COMP is clamped at 2.7V. If this condition is maintained for 1024 oscillator clock periods at any time following soft-start, the MAX1801 is disabled to prevent excessive output current. Restart the controller by cycling the voltage at DCON or IN to GND and back to a normal state. For a step-up application, short-circuit current is not limited, due to the DC current path through the inductor and output rectifier to the short circuit. If short-circuit protection is required in a step-up configuration, a protection device such as a fuse must be used to limit short-circuit current. Design Procedure The MAX1801 can operate in a number of DC-DC converter configurations, including step-up, SEPIC, and flyback. The following design discussions are limited to the step-up configuration shown in Figure 1; SEPIC and flyback examples are discussed in the Applications Information section. V R1 = R2 OUT − 1 V FB where V FB is 1.25V, the regulation set point for the MAX1801. Setting the Maximum Duty Cycle The master oscillator signal at OSC and the voltage at DCON are used to generate the internal clock signal (CLK in Figure 2). The internal clock’s falling edge occurs when V OSC exceeds V DCON , the voltage at DCON set by a resistive voltage-divider. The internal clock’s rising edge occurs when V OSC falls below 0.25V (Figure 3). The maximum duty cycle can be approximated by the equation: DMAX = R4 (1− fOSC tFALL ) R3 + R4 where fOSC and tFALL are the oscillator frequency (in Hz) and the fall time (typically 100ns), respectively. At 100kHz, the adjustable maximum duty-cycle range is typically 28% to 92% (see Maximum Duty Cycle vs. VDCON in the Typical Operating Characteristics). The maximum duty cycle typically defaults to 78% at 100kHz if VDCON is at or above the voltage at VREF (1.25V), and the controller shuts down if VDCON is less than 0.4V. If a resistive voltage-divider is used at DCON, shut down the MAX1801 by pulling DCON low with an open-drain signal from an external transistor. Drive DCON with appropriate logic levels to turn the MAX1801 on and off if the default duty-cycle limit is used. _______________________________________________________________________________________ 9 MAX1801 Switching Frequency The MAX1801 switching frequency is set by the MAX1800 or MAX1802 master converter (refer to the appropriate data sheet for the design procedure). Choose a switching frequency to optimize external component size or efficiency for the particular MAX1801 application. Typically, switching frequencies between 400kHz and 500kHz offer a good balance between component size and efficiency—higher frequencies generally allow smaller components, and lower frequencies give better conversion efficiency. MAX1801 Digital Camera Step-Up Slave DC-DC Controller Inductor Selection Select the inductor for either continuous or discontinuous current. Continuous conduction generally is the most efficient. Use discontinuous current if the step-up ratio (VOUT / VIN) is greater than 1 / ( 1 – DMAX ). Continuous Inductor Current For most MAX1801 step-up designs, a reasonable inductor value (LIDEAL) can be derived from the following equation, which sets continuous peak-to-peak inductor current at 1/3 the DC inductor current: LIDEAL = 3 (VIN − VSW ) D (1 − D) IOUT fOSC where D, the duty cycle, is given by: D ≈ 1− VIN VOUT + VD In these equations, VSW is the voltage drop across the N-channel MOSFET switch, and VD is the forward voltage drop across the rectifier. Given LIDEAL, the consistent peak-to-peak inductor current is 0.333 IOUT / (1 – D). The maximum inductor current is 1.167 IOUT / (1 – D). Inductance values smaller than LIDEAL can be used; however, the maximum inductor current will rise as L is reduced, and a larger output capacitance will be required to maintain output ripple. The inductor current will become discontinuous if IOUT decreases by more than a factor of six from the value used to determine LIDEAL. Discontinuous Inductor Current In the discontinuous mode of operation, the MAX1801 controller regulates the output voltage by adjusting the duty cycle to allow adequate power transfer to the load. To ensure regulation under worst-case load conditions (maximum IOUT), choose: V D L ≤ OUT MAX 2 IOUT fOSC The peak inductor current is VIN DMAX / (L fOSC). The inductor’s saturation current rating should meet or exceed the calculated peak inductor current. Input and Output Filter Capacitors The input capacitor (CIN) in step-up designs reduces the current peaks drawn from the battery or input power source and lessens switching noise in the controller. The impedance of the input capacitor at the switching frequency should be less than that of the 10 input source so that high-frequency switching currents do not pass through the input source. The output capacitor is required to keep the output voltage ripple small and to ensure stability of the regulation control loop. The output capacitor must have low impedance at the switching frequency. Tantalum and ceramic capacitors are good choices. Tantalum capacitors typically have high capacitance and medium-tolow equivalent series resistance (ESR) so that ESR dominates the impedance at the switching frequency. In turn, the output ripple is approximately: VRIPPLE ≈ IL(PEAK) ESR where IL(PEAK) is the peak inductor current. Ceramic capacitors typically have lower ESR than tantalum capacitors, but with relatively small capacitance that dominates the impedance at the switching frequency. In turn, the output ripple is approximately: VRIPPLE ≈ IL(PEAK) ZC where IL(PEAK) is the peak inductor current, and ZC ≈ 1 / (2 p fOSC COUT ). See the Compensation Design section for a discussion of the influence of output capacitance and ESR on regulation control loop stability. The capacitor voltage rating must exceed the maximum applied capacitor voltage. For most tantalum capacitors, manufacturers suggest derating the capacitor by applying no more than 70% of the rated voltage to the capacitor. Ceramic capacitors are typically used up to the voltage rating of the capacitor. Consult the manufacturer’s specifications for proper capacitor derating. Bypass Capacitors If the MAX1801 is placed far from the MAX1800 or MAX1802 master IC, noise from switching circuits can affect the MAX1801. Should this be the case, bypass REF and IN with 0.1µF or greater ceramic capacitors. If noise is not a problem or if the MAX1801 is placed close to the master IC, then no extra bypassing is required. MOSFET Selection The MAX1801 controller drives an external logic-level N-channel MOSFET as the circuit switch element. The key selection parameters are as follows: • On-resistance (RDS(ON)) • Maximum drain-to-source voltage (VDS(MAX)) • Minimum threshold voltage (VTH(MIN)) • Total gate charge (Qg) • Reverse transfer capacitance (CRSS) ______________________________________________________________________________________ Digital Camera Step-Up Slave DC-DC Controller where D is the duty cycle, IL is the average inductor current, and RDS(ON) is the on-resistance of the MOSFET. The transition loss is approximately: The frequency of the single pole due to the PWM converter is: PO = (2 VOUT – VIN ) / (2 π (VOUT – VIN) RLOAD COUT) And the DC gain of the PWM controller is: AVO = 2 VOUT (VOUT – VIN) RLOAD / ((2 VOUT – VIN) D) Note that the pole frequency decreases and the DC gain increases proportionally as the load resistance (RLOAD) is increased. Since the crossover frequency is the product of the pole frequency and the DC gain, it remains independent of the load. The gain through the voltage-divider is: V I f t P2 ≈ OUT L OSC T 3 where VOUT is the output voltage, IL is the average inductor current, fOSC is the converter switching frequency, and tT is the transition time. The transition time is approximately Qg / IG, where Qg is the total gate charge and IG is the gate drive current (typically 0.5A). The total power dissipation in the MOSFET is: AVDV = VREF / VOUT And the DC gain of the error amplifier is AVEA = 2000V/V. Thus, the DC loop gain is: AVDC = AVDV AVEA AVO The compensation resistor-capacitor pair at COMP cause a pole and zero at frequencies (in Hz): PC = GEA / (4000 π CC) = 1 / (4 x 107 π CC) PMOSFET = P1 + P2 Diode Selection For low-output-voltage applications, use a Schottky diode to rectify the output voltage because of the diode’s low forward voltage and fast recovery time. Schottky diodes exhibit significant leakage current at high reverse voltages and high temperatures. Thus, for high-voltage, high-temperature applications, use ultrafast junction rectifiers. ZC = 1 / (2 π RC CC) And the ESR of the output filter capacitor causes a zero in the loop response at the frequency (in Hz): ZO = 1 / (2π COUT ESR) The DC gain and the poles and zeros are shown in the Bode plot of Figure 4. To achieve a stable circuit with the Bode plot of Figure 4, perform the following procedure: Compensation Design MAX1801 converters use voltage mode to regulate their output voltages. The following explains how to compensate the control system for optimal performance. The compensation differs depending on whether the inductor current is continuous or discontinuous. 180° 80 AVDC 60 PC PHASE Discontinuous Inductor Current For discontinuous inductor current, the PWM converter has a single pole. The pole frequency and DC gain of the PWM controller are dependent on the operating duty cycle, which is: D = (2 L fOSC / RE)1/2 where RE is the equivalent load resistance, or: RE = VIN2 RLOAD / (VOUT (VOUT – VIN)) 90° 40 ZC = P O GAIN (dB) PHASE 20 GAIN 0° O ZO -20 FREQUENCY Figure 4. MAX1801 Discontinuous-Current, Voltage-Mode, Step-Up Converter Bode Plot ______________________________________________________________________________________ 11 MAX1801 Since the external gate drive (DL) swings between IN and GND, use a MOSFET whose on-resistance is specified at or below VIN. The gate charge, Qg, includes all capacitance associated with gate charging and helps to predict the transition time required to drive the MOSFET between on and off states. The power dissipated in the MOSFET is due to on-resistance and transition losses. The on-resistance loss is: P1 ≈ D IL2 RDS(ON) MAX1801 Digital Camera Step-Up Slave DC-DC Controller 1) Choose the compensation resistor RC that is equivalent to the inverse of the transconductance of the error amplifier, 1/ RC = GEA = 100µS, or RC = 10kΩ. This sets the high-frequency voltage gain of the error amplifier to 0dB. 2) Determine the maximum output pole frequency: PO(MAX) = 2VOUT - VIN 2π(VOUT - VIN ) RLOAD(MIN) COUT where: RLOAD(MIN) = VOUT / IOUT(MAX) 3) Place the compensation zero at the same frequency as the maximum output pole frequency (in Hz): ZC = 1 2VOUT - VIN = 2π RCCC 2π(VOUT - VIN ) RLOAD(MIN) COUT Solving for CC: VOUT - VIN CC = COUT VOUT RC IOUT(MAX) (2VOUT - VIN ) Use values of CC less than 10nF. If the above calculation determines that the capacitor should be greater than 10nF, use CC = 10nF, skip step 4 , and proceed to step 5. 4) Determine the crossover frequency (in Hz): fC = VREF / (π D COUT) and to maintain at least a 10dB gain margin, make sure that the crossover frequency is less than or equal to 1/3 of the ESR zero frequency, or: fC = (GEA RC) 2 VREF / (2π D COUT) ≥ 1 / (2π RC CC) Choose COUT, RC, and CC to simultaneously satisfy both equations. Continuous Inductor Current For continuous inductor current, there are two conditions that change, requiring different compensation. The response of the control loop includes a right-halfplane zero and a complex pole pair due to the inductor and output capacitor. For stable operation, the controller loop gain must drop below unity (0dB) at a much lower frequency than the right-half-plane zero frequency. The zero arising from the ESR of the output capacitor is typically used to compensate the control circuit by increasing the phase near the crossover frequency, increasing the phase margin. If a low-value, low-ESR output capacitor (such as a ceramic capacitor) is used, the ESR-related zero occurs at too high a frequency and does not increase the phase margin. In this case, use a lower value inductor so that it operates with discontinuous current (see the Discontinuous Inductor Current section). For continuous inductor current, the gain of the voltage divider is AVDV = VREF / VOUT, and the DC gain of the error amplifier is AVEA = 2000. The gain through the PWM controller in continuous current is: AVO = (1 / VREF) (VOUT2 / VIN) Thus, the total DC loop gain is: AVDC = 2000 VOUT / VIN The complex pole pair due to the inductor and output capacitor occurs at the frequency (in Hz): PO = (VOUT / VIN) / (2π (L × COUT)1/2) The pole and zero due to the compensation network at COMP occur at the frequencies (in Hz): 3fC ≤ ZO PC = GEA / (4000 π CC) = 1 / (4 x 107 π CC) ZC = 1 / (2π RC CC) ESR ≤ D / 6 VREF The frequency (in Hz) of the zero due to the ESR of the output capacitor is: If this is not the case, go to step 5 to reduce the error amplifier high-frequency gain to decrease the crossover frequency. 5) The high-frequency gain may be reduced, thus reducing the crossover frequency, as long as the zero due to the compensation network remains at or below the crossover frequency. In this case: ZO = 1 / (2π COUT ESR) or: ESR ≤ D / (GEA RC 6 VREF) and: 12 And the right-half-plane zero frequency (in Hz) is: ZRHP = (1- D)2 RLOAD 2πL The Bode plot of the loop gain of this control circuit is shown in Figure 5. ______________________________________________________________________________________ Digital Camera Step-Up Slave DC-DC Controller 180° PC 6) Determine that the compensation resistor, RC for the compensation zero frequency, is equal to the complex pole-pair frequency: GAIN AVDC PHASE ZC=PO PHASE solving for RC: RC = (VIN / VOUT) ((L COUT)1/2 / CC) PHASE MARGIN Z0 GAIN MARGIN 0° ZrRHP FREQUENCY Figure 5. MAX1801 Continuous-Current, Voltage-Mode, Step-Up Converter Bode Plot To configure the compensation network for a stable control loop, set the crossover frequency at that of the zero due to the output capacitor ESR. Use the following procedure: 1) Determine the frequency of the right-half-plane zero: ZRHP = ZC = PO 90° GAIN (dB) O dB Solving this equation for CC: CC = VOUT (COUT)3/2 ESR2 / (20MΩ VIN (L)1/2) (1- D)2 RLOAD 2πL 2) Find the DC loop gain: AVDC = 2000 VOUT VIN 3) Determine the frequency of the complex pole pair due to the inductor and output capacitor: fO = (VOUT / VIN) / (2π (L COUT)1/2) 4) Since response is 2nd order (-40dB per decade) between the complex pole pair and the ESR zero, determine the desired amplitude at the complex pole pair to force the crossover frequency equal to the ESR zero frequency. Thus: A(PO) = (ZO / PO)2 = L VIN2 / (COUT ESR2 VOUT2) Applications Information Using the MAX1801 with the MAX1800 Step-Up Master DC-DC Converter The MAX1801 does not generate its own reference or oscillator. Instead it uses the reference and the oscillator from a master DC-DC converter such as the MAX1800 step-up master converter. The MAX1800 has circuitry to generate a 1.25V reference and a 100kHz to 1MHz oscillator signal. The MAX1800 operates from a 1.5V to 5.5V input voltage, which makes it suitable for applications with 2- or 3-cell alkaline, NiCd, or NiMH batteries, or 1-cell lithium primary or lithium-ion (Li+) batteries. Apart from the reference and the oscillator, the MAX1800 has a single-internal-switch synchronous-rectified step-up DC-DC converter, three auxiliary step-up DC-DC converter controllers, and a linear regulator controller. For more details, refer to the MAX1800 data sheet Using the MAX1801 with the MAX1802 Step-Down Master DC-DC Converter The MAX1801 does not generate its own reference or oscillator. Instead, it uses the reference and the oscillator from a master DC-DC converter such as the MAX1802 step-down master DC-DC converter. The MAX1802 has circuitry to generate a 1.25V reference and a 100kHz to 1MHz oscillator signal. The MAX1802 operates from a 2.7V to 11V input voltage, making it suitable for 4-series alkaline, NiCd, or NiMH cells, or 2series lithium primary or (Li+) batteries. The MAX1802 has a synchronous-rectified step-down DC-DC converter controller, an internal-switch synchronous-rectified step-down DC-DC converter, and three auxiliary stepup DC-DC converter controllers. For more details, refer to the MAX1802 data sheet. 5) Determine the desired compensation pole. Since the response between the compensation pole and the complex pole pair is 1st order (-20dB per decade), the ratio of the frequencies is equal to the ratio of the amplitudes at those frequencies. Thus: ______________________________________________________________________________________ 13 MAX1801 (PO / PC) = (ADC / A(PO)) MAX1801 Digital Camera Step-Up Slave DC-DC Controller INPUT 1 CELL Li+ L2 MAIN ON DCON EXT C2 Q1 OUTPUT 3.3V D1 R1 MAX1801 FB COMP R2 RC Using the MAX1801 Controller for a Multi-Output Flyback Circuit GC Figure 6. MAX1801 Auxiliary Controller, SEPIC Configuration + OUTPUT D3 INPUT MAIN D2 - OUTPUT ON DCON EXT Q1 R1 MAX1801 FB COMP step-down converter is suitable; use a step-up/stepdown converter instead. One type of step-up/stepdown converter is the SEPIC shown in Figure 6. Inductors L1 and L2 can be separate inductors or can be wound on a single core and coupled as with a transformer. Typically, using a coupled inductor improves efficiency because some power is transferred through the coupling so that less power passes through the coupling capacitor, C2. Likewise, C2 should be a low-ESRtype capacitor to improve efficiency. The coupling capacitor ripple current rating must be greater than the larger of the input and output currents. The MOSFET (Q1) drain-source voltage rating and the rectifier (D1) reverse voltage rating must exceed the sum of the input and output voltages. Other types of step-up/step-down circuits are a flyback converter and a step-up converter followed by a linear regulator. R2 RC GC Figure 7. MAX1801 Auxiliary Controller, Flyback Configuration Using the MAX1801 Controller in SEPIC Configuration Some applications require multiple voltages from a single converter that features a flyback transformer. Figure 7 shows a MAX1801 auxiliary controller in a twooutput flyback configuration. The controller drives an external MOSFET that switches the transformer primary, and the two secondaries generate the outputs. Only a single positive output voltage can be regulated using the feedback resistive voltage-divider, so the other voltages are set by the turns ratio of the transformer secondaries. The regulation of the other secondary voltages degrades due to transformer leakage inductance and winding resistance. Voltage regulation is best when the load current is limited to a small range. Consult the transformer manufacturer for the proper design for a given application. Using a Charge Pump to Make Negative Output Voltages Negative output voltages can be produced without a transformer using a charge-pump circuit with an auxiliary controller, as shown in Figure 8. When MOSFET Q1 turns off, the voltage at its drain rises to supply current to VOUT+. At the same time, C1 charges to the voltage at VOUT+ through D1. When the MOSFET turns on, C1 discharges through D3, thereby charging C3 to VOUTminus the drop across D3, to create roughly the same voltage as VOUT+ at VOUT- but with inverted polarity. If different magnitudes are required for the positive and negative voltages, a linear regulator can be used at one of the outputs to achieve the desired voltages, while the MAX1801 regulates the higher magnitude voltage. In cases where the battery voltage is above or below the required output voltage, neither a step-up nor a 14 ______________________________________________________________________________________ Digital Camera Step-Up Slave DC-DC Controller VOUT- INPUT C3 D1 MAIN L C1 D2 VOUT+ ON DCON Q1 EXT C2 R1 MAX1801 FB COMP R2 RC GC Figure 8. Auxiliary Controller, Charge-Pump Configuration Designing a PC Board A good PC board layout is important to achieve optimal performance from the MAX1801. Poor design can cause excessive conducted and/or radiated noise, both of which can cause instability and/or regulation errors. Conductors carrying discontinuous currents should be kept as short as possible, and conductors carrying high currents should be made as wide as possible. A separate low-noise ground plane containing the reference and signal grounds should connect only to the power-ground plane at one point to minimize the effects of power-ground currents. Keep the voltage feedback network very close to the IC, preferably within 0.2in (5mm) of the FB pin. Nodes with high dv/dt (switching nodes) should be kept as small as possible and should be kept away from highimpedance nodes such as FB. Circuit-board layouts that are susceptible to electrical noise can require a lowpass RC filter at OSC and bypassing at REF and IN. If an RC filter is used at OSC, the pole frequency should be at least 20 times larger than the oscillator frequency to prevent distortion of the OSC signal. To ensure minimal loading of the master oscillator, which would cause an oscillator frequency shift, choose a filter capacitor smaller than COSC/(100 N), where COSC is the timing capacitor for the master oscillator and N is the number of MAX1801 slaves connected to the master. Then choose RFILTER = 1/(40 π fOSC CFILTER). If bypass capacitors are required on IN and REF, use 0.1µF ceramic capacitors because of their low impedance at high frequencies. The bypass and filter components should be placed within 5mm (0.2in) of the MAX1801 pins. Refer to the MAX1800 evaluation kit (EV kit) or MAX1802 EV kit data sheets for full PC board examples. Pin Configuration Chip Information TRANSISTOR COUNT: 1130 TOP VIEW OSC 1 GND 2 8 DL 7 IN 3 6 FB DCON 4 5 COMP MAX1801 REF SOT23-8 ______________________________________________________________________________________ 15 MAX1801 D3 Digital Camera Step-Up Slave DC-DC Controller SOT23, 8L.EPS MAX1801 Package Information Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2000 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.