BVLED BVU

BRIGHT VIEW
ELECTRONICS CO.,LTD
OVAL LED LAMP
BVU-439GN9
PACKAGE CONFIGURATION
BV-439
BV-439R
4.3
DESCRIPTION
4.3
3.2
Dice Material : GaN Green
Light Color : Green Color
Lens Color : Green Tinted Diffused
Stand-Off P/N : BVU-439GN9 R
3.2
4.3
4.1
6.5
4.3
4.1
1.0Max. 10.2 0.5
RADIATION PATTERN
30°
0°
-30°
1.3
1.0
25.4Min.
-60°
25.4Min.
60°
CATHODE
CATHODE
0.5
100 75 50 25
0 25 50 75 100
Relative Luminous Intensity ( Iv % )
2.54
2.54
1.0Min
Tolerance ± 0.25 ㎜
ABSOLUTE MAXIMUM RATINGS AT Ta = 25 ℃
PARAMETER
MAX.
Power Dissipation (PD)
Continuous Forward Current (IF)
Peak Forward Current ( 1/10 Duty Cycle , 10ms Pulse Width ) (IFP)
Reverse Voltage (VR)
120
30
100
5
0.4
Derating Linear From 25 ℃
Operating Temperature Range (Topr)
-30 ℃ to + 85 ℃
Storage Temperature Range (Tstg)
-40 ℃ to + 100 ℃
Lead Solder Temperature 1.6 mm Below Package 260 ℃ for 5 seconds (Tsld)
UNIT
mW
mA
mA
V
mA/oC
ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta = 25 ℃
SYMBOL
VF
IR
λp
λd
2θ1/2
IV
PARAMETER
TEST COND.
Forward Voltage
Reverse Current
Peak Emission Wavelength
Dominant Wavelength
Viewing Angle
Luminous Intensity
I F = 20 mA
V R = 5V
I F = 20 mA
I F = 20 mA
I F = 20 mA
I F = 20 mA
MIN.
TYP.
MAX.
3.3
4.0
10
μA
nm
nm
Deg
mcd
520
525
100/40
2800
2180
UNIT
V
BIN GRADE LIMITS (IF=20 mA)
LUMINOUS INTENSITY / mcd
BIN GRADE LIMITS (IF=20 mA)
DOMINANT WAVELENGTH / nm
Bin
M
N
O
Bin
PH
PI
PJ
Min.
2180
2800
3600
Min.
521
524
527
Max.
2800
3600
4650
Max.
524
527
530
Tolerance ± 15%mcd
*Bright View reserves the rights to alter specifications and remove availability of products at any time without notice.
*Dominant Wavelength, λd is according to CIE Chromaticity Diagram base on color of lamps.
*θ1/2 is the off-axis angle where the luminous intensity is one half the on-axis intensity.
*These products are sensitive to static electricity. Caution must be taken strictly to avoid static electricity.
2009/5/4 – A
BRIGHT VIEW
ELECTRONICS CO.,LTD
OVAL LED LAMP
BVU-439GN9
TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES
Relative Luminous Intensity.
Normalized at 20mA
Forward Current ( mA )
120
FIG. 1 Forward Current vs.
( Ta = 25 °C )
Forward Voltage
100
80
60
40
20
0
2.3
5.0
4.0
3.0
2.0
1.0
0
4.3
FIG. 3 Relative Forward Voltage vs.
Temperature
Relative Luminous Intensity.
Normalized at 20mA
Relative Forward Voltage.
Normalized at 20mA
1.2
2.8
3.3
3.8
Forward Voltage Vf ( V )
1.1
1.0
0.9
0.8
-50
-25
0
25
50
75
FIG. 2 Relative Luminous Intensity vs.
Forward Current ( Ta = 25 °C )
3.0
0
2.0
1.5
1.0
0.5
40
Forward Current ( mA )
Relative Emission Intensity (a.u.)
0.5
500
550
Wavelength ( nm )
0
25
50
75
100 125
Ambient Temperature Ta ( °C )
FIG. 5 Relative Intensity vs. Wavelength ( λp )
( If =20mA , Ta = 25 °C )
0
450
120
2.5
0
-50 -25
100 125
60
40
80 100
Forward Current If ( mA )
FIG. 4 Relative Luminous Intensity vs.
Temperature
Ambient Temperature Ta ( °C )
1.0
20
600
FIG. 6 Maximum Forward Current
vs. Temperature
30
20
10
0
0
20
40
60
80 100
Ambient Temperature Ta ( °C )
120
2009/5/4 – A
BRIGHT VIEW
ELECTRONICS CO.,LTD
OVAL LED LAMP
BVU-439GN9
CAUTION FOR CLASS 1 ESD ( MACHINE MODE )
Gallium Nitride (GaN) based light emitting diodes (LEDs) are extremely sensitive to electrostatic
discharge (ESD). Users are strongly recommended to take necessary meter to test the static
and avoid ESD when handing these products.
Bright View's BA, GN, WI series products are GaN based materials and are classified as
"Class 1",( ESD endurance 50V or lower ), any manufacturing site or workstation where
GaN devices are handled should be rated and controlled at 50V or below.
Proper grounding of products or machines ( via 1MΩ ), using static dissipative mats, static
dissipative containers, static dissipative working uniferms and shoes are considered to be
effective against ESD.
An ionizer is recommended in the facility or environment where ESD may be generated
easily, and soldering iron with a grounded tip is also recommended.
To install a protection device in the LED circuit to ensure the surge current and voltage not
exceeding the max rating during on/off swithing.
When inspecting the final products in which LEDs are assembled, it is recommended to
check whether the assembled LEDs are damaged by ESD or not. It is simple to find
damaged LEDs by light-on or a VF test at lower current (below 1mA is recommended).
ESD damaged LEDs will show some unusual characteristics such as the remarkable
increasing of leak current, the forward voltage become lower, or the LEDs do not light on
at the low current.
2009/5/4 – A
BRIGHT VIEW
ELECTRONICS CO.,LTD
OVAL LED LAMP
BVU-439GN9
Apply to LAMP(DIP) series.
Description:
( 1 ) Manual soldering (Solder Iron)
(1.1) Temperature at tip of the iron: 300°C Max.
(1.2) It's banned to load any stress on the resin during soldering.
(1.3) Soldering time: 3 sec. Max.(one time only)
(1.4) Leave 3mm of minimum distance from the base of epoxy.
( 2 ) Dip Soldering(Wave soldering-Solder Bath)
(2.1) Leave 3mm of minimum distance from the base of the epoxy.
Soldering beyond the base of the tie bar(stand off) is recommended.
(2.2) When soldering, do not put stress on the LEDs during heating.
(2.3) Cutting the leadframes at high temperatures may cause LED failure.
(2.4) Never take next process until the component is cooled down to room temperature
after reflow.
(2.5) After soldering, do not warp the circuit board.
(2.6) The recommended dip soldering profile is the following:
Temperature ( C )
Degree C.
300.0
275.0
250.0
225.0
200.0
175.0
150.0
125.0
100.0
75.0
50.0
25.0
0.0
MAX 260 C , 5 sec.
>20 C
4 C / sec.
150 C
0.0
50.0
100.0
150.0
200.0
250.0
300.0
Time ( sec. )
2009/5/4 – A
BRIGHT VIEW
ELECTRONICS CO.,LTD
OVAL LED LAMP
BVU-439GN9
Label 2
Label 1
Bright View
Bright View
Electronics Co.,Ltd.
BVU-XXXXXXXX
PART NO.:
LOT NO.:
GRADE:
Q'ty
LOT NO.:
X-
pcs
GRADE:
QA
Pb - Free / RoHS Compliant
3mm or 5mm Polybag
Anti-electrostatic bag
Q'ty
pcs
QA
Pb - Free / RoHS Compliant
ELECTROSTATIC SENSITIVE DEVICES
DO NOT OPEN OR HANDLE EXCEPT
AT A STATIC-FREE WORKSTATION
X: Bin grade
: Wavelength
: Vf
BOX
Dimension(cm): 29*25*15
BVU - X X X X X X X R
25
29
Stand-offs
Luminous Grade-refer to the selection guide for BIN options
Lens Color-refer to lens color (1) to (9)
Dice Code-refer to the selection guide
Lens Configuration-refer to lens drawing
View Angle-refer to the selection guide (A) to (Z)
Outline Dimension-refer to the outline dimension
3
15
TYPE
Q'TY
N,W
G,W
C.NO
Electronics Co.,Ltd.
PART NO.:
PCS
KGS
KGS
Label 1 or Label 2 attach on it.
Device
Q'ty / Polybag (pcs)
Fig.
Polybag / Box A
5mm(T-1 3/4)
1000pcs
14 bags
Label 1
3mm(T-1)
1000pcs
20 bags
Label 1
500pcs
18 bags
Label 2
Blue / Green / White
32
53
RE
Y
CARTON
Dimension(cm): 53*32*33
33
ITEM NO.
DEVICE:
Q'TY
N. W.:
G. W.:
PCS.
KGS.
KGS.
4 Boxes / Carton
5mm : 56,000pcs
3mm : 80,000pcs
Blue / Green / White : 36,000pcs
2009/5/4 – A