CYPRESS FM28V100-TG

FM28V100
1Mbit Bytewide F-RAM Memory
Features
1Mbit Ferroelectric Nonvolatile RAM
Organized as 128Kx8
High Endurance 100 Trillion (1014) Read/Writes
NoDelay™ Writes
Page Mode Operation to 33MHz
Advanced High-Reliability Ferroelectric Process
Superior to Battery-backed SRAM Modules
No battery concerns
Monolithic reliability
True surface mount solution, no rework steps
Superior for moisture, shock, and vibration
General Description
SRAM Replacement
JEDEC 128Kx8 SRAM pinout
60 ns Access Time, 90 ns Cycle Time
Low Power Operation
2.0V – 3.6V Power Supply
Standby Current 90 A (typ)
Active Current 7 mA (typ)
Industry Standard Configurations
Industrial Temperature -40 C to +85 C
32-pin “Green”/RoHS Package
Pin Configuration
The FM28V100 is a 128K x 8 nonvolatile memory
that reads and writes like a standard SRAM. A
ferroelectric random access memory or F-RAM is
nonvolatile, which means that data is retained after
power is removed. It provides data retention for over
10 years while eliminating the reliability concerns,
functional disadvantages, and system design
complexities of battery-backed SRAM (BBSRAM).
Fast write timing and very high write endurance make
F-RAM superior to other types of memory.
In-system operation of the FM28V100 is very similar
to other RAM devices and can be used as a drop-in
replacement for standard SRAM. Read and write
cycles may be triggered by toggling a chip enable pin
or simply by changing the address. The F-RAM
memory is nonvolatile due to its unique ferroelectric
memory process. These features make the FM28V100
ideal for nonvolatile memory applications requiring
frequent or rapid writes in the form of an SRAM.
A11
A9
A8
A13
WE
CE2
A15
VDD
NC*
A16
A14
A12
A7
A6
A5
A4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
TSOP-I
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE
A10
CE1
DQ7
DQ6
DQ5
DQ4
DQ3
VSS
DQ2
DQ1
DQ0
A0
A1
A2
A3
* Reserved for A17 on 2Mb
Ordering Information
FM28V100-TG
32-pin “Green”/RoHS TSOP
FM28V100-TGTR 32-pin “Green”/RoHS TSOP,
Tape & Reel
Device specifications are guaranteed over the
industrial temperature range -40°C to +85°C.
This product conforms to specifications per the terms of the Ramtron standard warranty. The product has completed Ramtron’s
internal qualification testing and has reached production status.
Cypress Semiconductor Corporation
•
Document Number: 001-86202 Rev. **
198 Champion Court
•
San Jose, CA 95134-1709 • 408-943-2600
Revised February 25, 2013
FM28V100 - 128Kx8 FRAM
A(16:3)
Row Decoder
Address Latch
A(16:0)
16K x 64
F-RAM Array
A(2:0)
...
Column Decoder
CE1, CE2 2
WE
Control
Logic
OE
I/O Latch & Bus Driver
DQ(7:0)
Figure 1. Block Diagram
Pin Descriptions
Pin Name
Type
A(16:0)
Input
/CE1, CE2
Input
/WE
Input
/OE
Input
DQ(7:0)
NC
VDD
VSS
I/O
Supply
Supply
Pin Description
Address inputs: The 17 address lines select one of 131,072 bytes in the F-RAM array. The
address value is latched on the falling edge of /CE1 (while CE2 high) or the rising edge of
CE2 (while /CE1 low). Addresses A(2:0) are used for page mode read and write operations.
Chip Enable inputs: The device is selected and a new memory access begins on the falling
edge of /CE1 (while CE2 high) or the rising edge of CE2 (while /CE1 low). The entire
address is latched internally at this point. The CE2 pin is pulled up internally.
Write Enable: A write cycle begins when /WE is asserted. The rising edge causes the
FM28V100 to write the data on the DQ bus to the F-RAM array. The falling edge of /WE
latches a new column address for fast page mode write cycles.
Output Enable: When /OE is low, the FM28V100 drives the data bus when valid data is
available. Deasserting /OE high tri-states the DQ pins.
Data: 8-bit bi-directional data bus for accessing the F-RAM array.
No Connect: This pin has no internal connection.
Supply Voltage
Ground
Document Number: 001-86202 Rev. **
Page 2 of 14
FM28V100 - 128Kx8 FRAM
Functional Truth Table 1
/CE1
CE2
H
X
X
L
H
L
L
H
L
H
H
L
L
H
L
H
H
L
/WE
X
X
H
H
H
H
L
L
X
X
A(16:3)
X
X
V
V
No Change
Change
V
V
V
No Change
X
X
A(2:0)
X
X
V
V
Change
V
V
V
V
V
X
X
Operation
Standby/Idle
Read
Page Mode Read
Random Read
/CE-Controlled Write 2
/WE-Controlled Write 2, 3
Page Mode Write 4
Starts Precharge
Notes:
1) H=Logic High, L=Logic Low, V=Valid Address, X=Don’t Care.
2) For write cycles, data-in is latched on the rising edge of /CE1 or /WE of the falling edge of CE2, whichever
comes first.
3) /WE-controlled write cycle begins as a Read cycle and A(16:3) is latched then.
4) Addresses A(2:0) must remain stable for at least 15 ns during page mode operation.
Document Number: 001-86202 Rev. **
Page 3 of 14
FM28V100 - 128Kx8 FRAM
Overview
The FM28V100 is a bytewide F-RAM memory
logically organized as 131,072 x 8 and is accessed
using an industry standard parallel interface. All data
written to the part is immediately nonvolatile with no
delay. The device offers page mode operation which
provides higher speed access to addresses within a
page (row). An access to a different page is triggered
by toggling a chip enable pin or simply by changing
the upper address A(16:3).
Memory Operation
Users access 131,072 memory locations with 8 data
bits each through a parallel interface. The F-RAM
array is organized as 16,384 rows and each row has 8
column locations (bytes), which allows fast access in
page mode operation. Once an initial address has
been latched by the falling edge of /CE1 (while CE2
high) or the rising edge of CE2 (while /CE1 low),
subsequent column locations may be accessed
without the need to toggle a chip enable. When either
chip enable pin is deasserted, a precharge operation
begins. Writes occur immediately at the end of the
access with no delay. The /WE pin must be toggled
for each write operation.
Read Operation
A read operation begins on the falling edge of /CE1
(while CE2 high) or the rising edge of CE2 (while
/CE1 low). The /CE-initiated access causes the
address to be latched and starts a memory read cycle
if /WE is high. Data becomes available on the bus
after the access time has been satisfied. Once the
address has been latched and the access completed, a
new access to a random location (different row) may
begin while both chip enables are still active. The
minimum cycle time for random addresses is tRC.
Note that unlike SRAMs, the FM28V100’s /CEinitiated access time is faster than the address cycle
time.
The FM28V100 will drive the data bus only when
/OE is asserted low and the memory access time has
been satisfied. If /OE is asserted prior to completion
of the memory access, the data bus will not be driven
until valid data is available. This feature minimizes
supply current in the system by eliminating transients
caused by invalid data being driven onto the bus.
When /OE is inactive, the data bus will remain hi-Z.
Write Operation
Writes occur in the FM28V100 in the same time
interval as reads. The FM28V100 supports both /CEand /WE-controlled write cycles. In both cases, the
address is latched on the falling edge of /CE1 (while
CE2 high) or the rising edge of CE2 (while /CE1
low).
Document Number: 001-86202 Rev. **
In a /CE-controlled write, the /WE signal is asserted
prior to beginning the memory cycle. That is, /WE is
low when the device is activated with a chip enable.
In this case, the device begins the memory cycle as a
write. The FM28V100 will not drive the data bus
regardless of the state of /OE as long as /WE is low.
Input data must be valid when the device is
deselected with a chip enable. In a /WE-controlled
write, the memory cycle begins when the device is
activated with a chip enable. The /WE signal falls
some time later. Therefore, the memory cycle begins
as a read. The data bus will be driven if /OE is low,
however it will hi-Z once /WE is asserted low. The
/CE- and /WE-controlled write timing cases are
shown on page 12. In the Write Cycle Timing 2
diagram, the data bus is shown as a hi-Z condition
while the chip is write-enabled and before the
required setup time. Although this is drawn to look
like a mid-level voltage, it is recommended that all
DQ pins comply with the minimum VIH/VIL operating
levels.
Write access to the array begins on the falling edge of
/WE after the memory cycle is initiated. The write
access terminates on the deassertion of /WE, /CE1, or
CE2, whichever comes first. A valid write operation
requires the user to meet the access time specification
prior to deasserting /WE, /CE1, or CE2. Data setup
time indicates the interval during which data cannot
change prior to the end of the write access.
Unlike other truly nonvolatile memory technologies,
there is no write delay with F-RAM. Since the read
and write access times of the underlying memory are
the same, the user experiences no delay through the
bus. The entire memory operation occurs in a single
bus cycle. Data polling, a technique used with
EEPROMs to determine if a write is complete, is
unnecessary.
Page Mode Operation
The FM28V100 provides the user fast access to any
data within a row element. Each row has eight
column locations (bytes). An access can start
anywhere within a row and other column locations
may be accessed without the need to toggle the CE
pins. For page mode reads, once the first data byte is
driven onto the bus, the column address inputs A(2:0)
may be changed to a new value. A new data byte is
then driven to the DQ pins. For page mode writes,
the first write pulse defines the first write access.
While the device is selected (both chip enables
asserted), a subsequent write pulse along with a new
column address provides a page mode write access.
Page 4 of 14
FM28V100 - 128Kx8 FRAM
Precharge Operation
The precharge operation is an internal condition in
which the state of the memory is prepared for a new
access. Precharge is user-initiated by driving at least
one of the chip enable signals to an inactive state. The
chip enable must remain inactive for at least the
minimum precharge time tPC.
Precharge is also activated by changing the upper
addess A(16:3). The current row is first closed prior
Endurance
The FM28V100 is capable of being accessed at least
1014 times – reads or writes. An F-RAM memory
operates with a read and restore mechanism.
Therefore, an endurance cycle is applied on a row
basis. The F-RAM architecture is based on an array
of rows and columns. Rows are defined by A16-A3
and column addresses by A2-A0. The array is
organized as 16K rows of 8-bytes each. The entire
row is internally accessed once whether a single byte
or all eight bytes are read or written. Each byte in the
row is counted only once in an endurance calculation.
to accessing the new row. The device automatically
detects an upper order address change which starts a
precharge operation, the new address is latched, and
the new read data is valid within the tAA address
access time. Refer to the Read Cycle Timing 1
diagram on page 9. Likewise a similar sequence
occurs for write cycles. Refer to the Write Cycle
Timing 3 diagram on page 11. The rate at which
random addresses can be issued is tRC and tWC,
respectively.
The user may choose to write CPU instructions and
run them from a certain address space. The table
below shows endurance calculations for 256-byte
repeating loop, which includes a starting address, 7
page mode accesses, and a CE precharge. The
number of bus clocks needed to complete an 8-byte
transaction is 8+1 at lower bus speeds, but 9+2 at
33MHz due to initial read latency and an extra clock
to satisfy the device’s precharge timing constraint tPC.
The entire loop causes each byte to experience only
one endurance cycle.
F-RAM read and write
endurance is virtually unlimited even at 33MHz
system bus clock rate.
Table 1. Time to Reach 100 Trillion Cycles for Repeating 256-byte Loop
Bus Freq Bus Cycle
256-byte
Endurance
Endurance
Years to
(MHz)
Time (ns) Transaction Cycles/sec.
Cycles/year
Reach 1014
Cycles
Time ( s)
30
10.56
33
94,690
2.98 x 1012
33.5
40
12.8
40.6
25
78,125
2.46 x 1012
10
100
28.8
34,720
1.09 x 1012
91.7
5
200
57.6
17,360
5.47 x 1011
182.8
Document Number: 001-86202 Rev. **
Page 5 of 14
FM28V100 - 128Kx8 FRAM
SRAM Drop-In Replacement
The FM28V100 has been designed to be a drop-in
replacement for standard asynchronous SRAMs. The
device does not require the CE pins to toggle for each
new address. Both CE pins may remain active
indefinitely while VDD is applied. When both CE pins
are active, the device automatically detects address
changes and a new access begins. It also allows page
mode operation at speeds up to 33MHz.
A typical application is shown in Figure 3. It shows a
pullup resistor on /CE1 which will keep the pin high
during power cycles assuming the MCU/MPU pin tristates during the reset condition. The pullup resistor
value should be chosen to ensure the /CE1 pin tracks
VDD yet a high enough value that the current drawn
when /CE1 is low is not an issue. Although not
required, it is recommended that CE2 be tied to VDD
if the controller provides an active-low chip enable.
VDD
The pullup resistor value should be chosen to ensure
the /WE pin tracks VDD yet a high enough value that
the current drawn when /WE is low is not an issue. A
10Kohm resistor draws 330uA when /WE is low and
VDD=3.3V.
VDD
R
MCU/
MPU
FM28V100
CE2
CE1
WE
OE
A(16:0)
DQ(7:0)
Figure 4. Use of Pullup Resistor on /WE
The FM28V100 is backward compatible with the
1Mbit FM20L08 and 256Kbit FM18L08 devices.
FM28V100
R
CE2
CE1
MCU/
MPU
WE
OE
A(16:0)
PCB Layout Recommendations
A 0.1uF decoupling capacitor should be placed close
to pin 8 (VDD) and the ground side of the capacitor
should be connected to either a ground plane or low
impedance path back to pin 24 (VSS). It is best to use
a chip capacitor that has low ESR and has good high
frequency characteristics.
DQ(7:0)
Figure 3. Typical Application using Pullup
Resistor on /CE1
For applications that require the lowest power
consumption, the CE signals should be active only
during memory accesses. Due to the external pullup
resistor, some supply current will be drawn while
/CE1 is low. When /CE1 is high, the device draws no
more than the maximum standby current ISB.
Note that if /CE1 is grounded and CE2 tied to VDD,
the user must be sure /WE is not low at powerup or
powerdown events. If the chip is enabled and /WE is
low during power cycles, data corruption will occur.
Figure 4 shows a pullup resistor on /WE which will
keep the pin high during power cycles assuming the
MCU/MPU pin tri-states during the reset condition.
Document Number: 001-86202 Rev. **
If the controller drives the address and chip enable
from the same timing edge, it is best to keep the
address routes short and of equal length. A simple RC
circuit may be inserted in the chip enable path to
provide some delay and timing margin for the
FM28V100’s address setup time tAS.
As a general rule, the layout designer may need to
add series termination resistors to controller outputs
that have fast transitions or routes that are > 15cm in
length. This is only necessary if the edge rate is less
than or equal to the round trip trace delay. Signal
overshoot and ringback may be large enough to cause
erratic device behavior. It is best to add a 50 ohm
resistor (30 – 60 ohms) near the output driver
(controller) to reduce such transmission line effects.
Page 6 of 14
FM28V100 - 128Kx8 FRAM
Electrical Specifications
Absolute Maximum Ratings
Symbol
Description
VDD
Power Supply Voltage with respect to VSS
VIN
Voltage on any signal pin with respect to VSS
TSTG
TLEAD
VESD
Storage Temperature
Lead Temperature (Soldering, 10 seconds)
Electrostatic Discharge Voltage
- Human Body Model (AEC-Q100-002 Rev. E)
- Charged Device Model (AEC-Q100-011 Rev. B)
- Machine Model (AEC-Q100-003 Rev. E)
Package Moisture Sensitivity Level
Ratings
-1.0V to +4.5V
-1.0V to +4.5V and
VIN < VDD+1V
-55 C to +125 C
260 C
2kV
1.25kV
200V
MSL-3
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating
only, and the functional operation of the device at these or any other conditions above those listed in the operational section of this
specification is not implied. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability.
DC Operating Conditions (TA = -40 C to +85 C, VDD = 2.0V to 3.6V unless otherwise specified)
Symbol Parameter
Min
Typ
Max
Units Notes
VDD
Power Supply
2.0
3.3
3.6
V
IDD
VDD Supply Current
7
12
mA
1
ISB
Standby Current – CMOS
90
150
2
A
ILI
Input Leakage Current
3
1
A
ILO
Output Leakage Current
3
1
A
VIH
Input High Voltage
0.7 VDD
VDD + 0.3
V
VIL
Input Low Voltage
-0.3
0.3 VDD
V
VOH1
Output High Voltage (IOH = -1 mA, VDD=2.7V)
2.4
V
VOH2
Output High Voltage (IOH = -100 A)
VDD-0.2
V
VOL1
Output Low Voltage (IOL = 2 mA, VDD=2.7V)
0.4
V
VOL2
Output Low Voltage (IOL = 150 A)
0.2
V
RIN
Address Input Resistance (CE2)
4
For VIN = VIH (min)
40
K
For VIN = VIL (max)
1
M
Notes
1. VDD = 3.6V, CE cycling at minimum cycle time. All inputs at CMOS levels (0.2V or VDD-0.2V), all DQ pins unloaded.
2. VDD = 3.6V, /CE1 at VDD or CE2 at VSS, and all other pins at CMOS levels (0.2V or VDD-0.2V).
3. VIN, VOUT between VDD and VSS.
4. The input pull-up circuit is stronger (>40K ) when the input voltage is above VIH and weak (>1M ) when the input
voltage is below VIL.
Document Number: 001-86202 Rev. **
Page 7 of 14
FM28V100 - 128Kx8 FRAM
Read Cycle AC Parameters (TA = -40 C to +85 C, CL = 30 pF, unless otherwise specified)
VDD 2.0 to 2.7V
VDD 2.7 to 3.6V
Symbol Parameter
Min
Max
Min
Max
tRC
Read Cycle Time
105
90
tCE
Chip Enable Access Time
70
60
tAA
Address Access Time
105
90
tOH
Output Hold Time
20
20
tAAP
Page Mode Address Access Time
40
30
tOHP
Page Mode Output Hold Time
3
3
tCA
Chip Enable Active Time
70
60
tPC
Precharge Time
35
30
tAS
Address Setup Time (to /CE1, CE2 active)
0
0
tAH
Address Hold Time (/CE-controlled)
70
60
tOE
Output Enable Access Time
25
15
tHZ
Chip Enable to Output High-Z
10
10
tOHZ
Output Enable High to Output High-Z
10
10
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes
Write Cycle AC Parameters (TA = -40 C to +85 C, unless otherwise specified)
VDD 2.0 to 2.7V
VDD 2.7 to 3.6V
Symbol Parameter
Min
Max
Min
Max
tWC
Write Cycle Time
105
90
tCA
Chip Enable Active Time
70
60
tCW
Chip Enable to Write Enable High
70
60
tPC
Precharge Time
35
30
tPWC
Page Mode Write Enable Cycle Time
40
30
tWP
Write Enable Pulse Width
22
18
tAS
Address Setup Time (to /CE1, CE2 active)
0
0
tAH
Address Hold Time (/CE-controlled)
70
60
tASP
Page Mode Address Setup Time (to /WE low)
8
5
tAHP
Page Mode Address Hold Time (to /WE low)
20
15
tWLC
Write Enable Low to Chip Disabled
30
25
tWLA
Write Enable Low to A(16:3) Change
30
25
tAWH
A(16:3) Change to Write Enable High
105
90
tDS
Data Input Setup Time
20
15
tDH
Data Input Hold Time
0
0
tWZ
Write Enable Low to Output High Z
10
10
tWX
Write Enable High to Output Driven
5
5
tWS
Write Enable to CE-Active Setup Time
0
0
tWH
Write Enable to CE-Inactive Hold Time
0
0
-
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes
1
1
1
1
1,2
1,2
Notes
1
This parameter is characterized but not 100% tested.
2
The relationship between CE’s and /WE determines if a /CE- or /WE-controlled write occurs.
Power Cycle Timing (TA = -40 C to +85 C, VDD = 2.0V to 3.6V unless otherwise specified)
Symbol
Parameter
Min
Max
tVR
VDD Rise Time
50
tVF
VDD Fall Time
100
tPU
Power Up (VDD min) to First Access Time
250
tPD
Last Access to Power Down (VDD min)
0
-
Units
s/V
s/V
s
s
Notes
1
1
Notes
1
Slope measured at any point on VDD waveform.
Document Number: 001-86202 Rev. **
Page 8 of 14
FM28V100 - 128Kx8 FRAM
Data Retention (TA = -40 C to + 85 C)
Parameter
Data Retention
Capacitance (TA = 25 C , f=1 MHz, VDD = 3.3V)
Symbol
Parameter
CI/O
Input/Output Capacitance (DQ)
CIN
Input Capacitance
Notes
1. This parameter is characterized and not 100% tested.
AC Test Conditions
Input Pulse Levels
Input rise and fall times
Input and output timing levels
Output Load Capacitance
Min
10
Max
-
Units
Years
Notes
Min
-
Max
8
6
Units
pF
pF
Notes
1
1
0 to 3V
3 ns
1.5V
30 pF
Read Cycle Timing 1 (/CE1 low, CE2 high, /OE low)
tRC
A(16:0)
tAA
tOH
tOH
DQ(7:0)
Read Cycle Timing 2 (/CE-controlled)
tCA
tPC
CE1
CE2
tAH
tAS
A(16:0)
tOE
tHZ
OE
tCE
tOHZ
DQ(7:0)
Document Number: 001-86202 Rev. **
Page 9 of 14
FM28V100 - 128Kx8 FRAM
Page Mode Read Cycle Timing
tPC
tCA
CE1
CE2
tAS
A(16:3)
A(2:0)
Col 0
Col 1
tOE
OE
Col 2
tAAP
tHZ
tOHZ
tOHP
tCE
Data 0
DQ(7:0)
Data 1
Data 2
Although sequential column addressing is shown, it is not required.
Write Cycle Timing 1 (/WE-Controlled) Note: /OE is low only to show effect of /WE on DQ pins
tCA
tPC
tCW
CE1
CE2
tWLC
tAS
A(16:0)
tWP
tWX
WE
DQ(7:0)
tWZ
tDH
tDS
D out
D in
tHZ
D out
Write Cycle Timing 2 (/CE-Controlled)
tPC
tCA
CE1
CE2
tAS
tAH
A(16:0)
tWH
WE
tWS
tDS
tDH
DQ(7:0)
NOTE: See Write Operation section for detailed description (page 4).
Document Number: 001-86202 Rev. **
Page 10 of 14
FM28V100 - 128Kx8 FRAM
Write Cycle Timing 3 (/CE1 low, CE2 high) Note: /OE is low only to show effect of /WE on DQ pins
tWC
tAWH
A(16:0)
tWLA
WE
tWX
tWZ
DQ(7:0)
tDS
D out
tDH
D in
D out
D in
Page Mode Write Cycle Timing
tCA
tPC
tCW
CE1
CE2
tWLC
tAS
A(16:3)
tAH
A(2:0)
tAHP
Col 0
tASP
Col 1
Col 2
tPWC
tWP
WE
OE
tDH
tDS
Data 0
DQ(7:0)
Data 1
Data 2
Although sequential column addressing is shown, it is not required.
Power Cycle Timing
VDD
VDD min
VDD min
t VR
t VF
t PU
t PD
Access Allowed
Document Number: 001-86202 Rev. **
Page 11 of 14
FM28V100 - 128Kx8 FRAM
Mechanical Drawing
32-pin Shrunk TSOP-I (8.0 x 13.4 mm)
All dimensions in millimeters
Recommended PCB Footprint
11.80 13.55
±0.10 13.30
14.20
0.50
Pin 1
1.60
0.30
8.00 ±0.10
1.20 max
0.50
typ
0.15
0.05
0.17-0.27
typ
0.21
0.10
0.10 mm
0°-5°
0.5-0.7
TSOP Package Marking Scheme
RAMTRON
XXXXXXX-P
RLLLLLLL
YYWW
Legend:
XXXXXX= part number, P= package/option (T=TSOP “Green”)
R=rev code, YY=year, WW=work week, LLLLLLL= lot code
Example: FM28V100, “Green”/RoHS TSOP-I package,
Rev. A, Year 2010, Work Week 18, Lot 9482296
RAMTRON
FM28V100-TG
A9482296TG
1018
Document Number: 001-86202 Rev. **
Page 12 of 14
FM28V100 - 128Kx8 FRAM
Revision History
Revision
1.0
1.1
Date
10/10/2008
3/25/2009
1.2
5/25/2010
3.0
4/24/2012
Summary
Initial release.
Added tape & reel ordering information. Added ESD ratings. Removed software
write protect feature.
Changed MSL package rating. Expanded explanation of precharge operation.
Updated lead temperature rating in Abs Max table. Changed package marking
scheme.
Changed to Production status.
Document History
Document Title: FM28V100 1Mbit (128Kx8) Bytewide F-RAM Memory
Document Number: 001-86202
Revision
ECN
Orig. of
Change
Submission
Date
**
3912933
GVCH
02/25/2013
Document Number: 001-86202 Rev. **
Description of Change
New Spec
Page 13 of 14
FM28V100 - 128Kx8 FRAM
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors.
To find the office closest to you, visit us at Cypress Locations.
Products
PSoC® Solutions
Automotive
cypress.com/go/automotive
Clocks & Buffers
cypress.com/go/clocks
Interface
cypress.com/go/interface
Lighting & Power Control
cypress.com/go/powerpsoc
cypress.com/go/plc
Cypress Developer Community
Memory
cypress.com/go/memory
Community | Forums | Blogs | Video | Training
PSoC
cypress.com/go/psoc
Touch Sensing
cypress.com/go/touch
Technical Support
USB Controllers
cypress.com/go/usb
cypress.com/go/support
psoc.cypress.com/solutions
PSoC 1 | PSoC 3 | PSoC 5
RAMTRON is a registered trademark and NoDelay™ is a trademark of Cypress Semiconductor Corp. All other trademarks or registered
trademarks referenced herein are the property of their respective owners.
© Cypress Semiconductor Corporation, 2011-2013. The information contained herein is subject to change without notice. Cypress
Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor
does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical,
life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore,
Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may
reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application
implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
This Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to
worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby
grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the
Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product
to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification,
translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written
permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume
any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use
as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to
the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use
and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-86202 Rev. **
Page 14 of 14