TS2496 2A / 150KHz Buck Switching Regulator TO-263-5L 2 (D PAK) Pin Definition: 1. Input 2. SW Output 3. Ground 4. Feedback 5. Enable General Description TS2496 Series are step-down switching regulators with all required active functions. It is capable of driving 2A load with excellent line and load regulations. These devices are available in fixed output voltages of 3.3V, 5V and an adjustable output version. TS2496 series operates at a switching frequency of 150kHz thus allowing smaller sized filter components than what would be needed with lower frequency switching regulators. It substantially not only reduces the area of board size but also the size of heat sink, and in some cases no heat sink is required. The ±4% tolerance on output voltage within specified input voltages and output load conditions is guaranteed. Also, the oscillator frequency accuracy is within ±10%. External shutdown is included. Featuring 80µA (typical) standby current. The output switch includes cycle-bycycle current limiting, as well as thermal shutdown for full protection under fault conditions. Features ● ● ● ● ● ● ● ● ● ● ● ● Ordering Information Output Voltage: 3.3V, 5V & Adjustable version Adjustable Output Voltage Range 1.23V~19.5V ±4% 150KHz fixed switching frequency Voltage Mode Non-synchronous PWM control Thermal Shutdown and Current Limit Protection ON/OFF Shutdown Control Input High Efficiency Short Circuit Protect (SCP) Operating Voltage Can be up to 24V Output Load Current 2A Low Power Standby Mode P+ Product Enhancement Tested Part No. Package Packing TS2496CMxx RN TO-263-5L 800pcs / 13” Reel Note: Where xx denotes voltage option, available are 50= 5.0V 33= 3.3V Leave blank for adjustable version Application ● ● ● Simple High-efficiency Step down Regulator On-Card Switching Regulators Positive to Negative Converter Absolute Maximum Rating Parameter Symbol Limit Unit Maximum Supply Voltage VCC +28 V Recommend Operating Supply Voltage VOP +4.5 to +24 V VSW, VEN -0.3 to VCC V Feedback Pin Voltage VFB -0.3 to VCC V Power Dissipation PD Internally Limited W VOUT -1 SW, EN Pin Input Voltage Output Voltage to Ground Storage Temperature Range TST Operating Temperature Range TOP ESD Susceptibility (HBM) -65 to +150 C -20 to +125 o C 2 1/7 V o kV Version: C07 TS2496 2A / 150KHz Buck Switching Regulator Thermal Information Parameter Symbol Maximum Unit Thermal Resistance* (Junction to Case) ӨJC 2 o Thermal Resistance* (Junction to Ambient) ӨJA 50 o C/W C/W 2 Note: Ө JA is measured with the PCB copper area (need connect to GROUND pins) of approximately 1.5 in (Multi-layer) Electrical Specifications (All Output Voltage Version) o (Ta = 25 C unless otherwise noted, VIN=12V for 3.3V, 5V, Adjustable version. ILOAD =0.2A) Parameter Symbol Output Feedback ADJ Efficiency VFB η Output Feedback 3.3V Efficiency VFB η Output Feedback 5V VFB Test Condition 4.5V≤ VIN ≤24V 0.2A≤ ILOAD ≤2A VIN =12V, ILOAD =2A 4.75V≤ VIN ≤24V 0.2A≤ ILOAD ≤2A VIN =12V, ILOAD =2A 7V≤ VIN ≤24V 0.2A≤ ILOAD ≤2A Min Typ Max Unit 1.180 1.23 1.280 V -- 75 -- % 3.135 3.3V 3.465 V -- 75 -- % 4.75 5 5.25 V Efficiency η VIN =12V, ILOAD =2A -- 80 -- % Feedback Bias Current IFB VFB =1.3V (Adj version only) -- 10 100 nA 127 150 173 KHz -- 3 -- mS 5.9 -- -- A 110 150 173 KHz -- 1.15 1.50 V Oscillator Frequency FOSC Soft-Start Time TSS Current Limit ICL Oscillator Frequency of Short Circuit Protect Saturation Voltage FSCP VSAT Rising edge of EN on to ICL Pear Current, no outside circuit VFB =0V force driver on When current limit occurred and o VFB <0.5V, Ta = 25 C IOUT=2A, No outside circuit VFB =0V force driver on ON/OFF Pin Logic Input Threshold VIL Low (regulator ON) Voltage VIH High (regulator OFF) ON/OFF Pin Logic Input Current Maximum Duty Cycle (ON) Maximum Duty Cycle (OFF) Quiescent Current SW Pin Leakage Current SW pin = 0 SW pin = -1 2.0 1.3 0.6 -- IL VLOGIC =2.5V (OFF) -- 5 15 IH VLOGIC =0.5V (ON) -- 0.02 5 VFB =0V force driver on -- 100 -- VFB =12V force driver off -- 0 -- VFB =12V force driver off -- 5 10 ON/OFF pin=5V -- VIN =40V -- DC IQ Standby Quiescent Current -- ISTBY No outside circuit, ISWL VFB =12V force driver off VIN =12V 2/7 80 200 250 V µA % mA µA -- 0.3 2 mA -- 7.5 30 mA Version: C07 TS2496 2A / 150KHz Buck Switching Regulator Block Diagram 3/7 Version: C07 TS2496 2A / 150KHz Buck Switching Regulator Typical Application Circuit 1. Adjustable Output Voltage Version 2. Fixed Output Voltage Version 3. Adjustable Output Voltage Version with Delayed Startup 4/7 Version: C07 TS2496 2A / 150KHz Buck Switching Regulator Pin Function Description Vcc This is the positive input supply for the IC switching regulator. A suitable input bypass capacitor must be presented at this pin to minimize voltage transients and to supply the switching currents needed by the regulator. Ground Circuit ground SW Output Internal switch. The voltage at this pin switches between (+Vcc – Vsat) and approximately – 0.5V, with a duty cycle of approximately Vout / Vcc. To minimize coupling to sensitive circuitry, the PC board copper area connected to this pin should be minimized. Feedback Sense the regulated output voltage to complete the feedback loop. Enable Allows the switching regulator circuit to be shutdown using logic level signals thus dropping the total input supply current to approximately 100uA. Pulling this pin below a threshold voltage of approximately 1.3V turns the regulator on, and pulling this pin above 1.3V (up to a maximum of Vcc) shuts the regulator down. If this shutdown feature is not needed, the EN pin can be wired to the ground pin. Thermal Considerations The TS2496 is available in two packages, a TO-220-5L and TO-263-5L. The TO-220-5L package needs a heat sink under most conditions. The size of the heat sink depends on the input voltage, the output voltage, the load current and the ambient temperature. The TS2496 junction temperature rises above ambient temperature for a 2A load and different input and output voltages. The data for these curves was taken o with the TS2496 (TO-220-5L package) operating as a buck switching regulator in an ambient temperature of 25 C (still air). These temperature rise numbers are all approximate and there are many factors that can affect these temperatures. Higher ambient temperatures require more heat sinking. The TO-263-5L surface mount package tab is designed to be soldered to the copper on a printed circuit board. The copper and the board are the heat sink for this package and the other heat producing components, such2as the catch diode and inductor. The PC board copper area that the package is soldered to should be at least 0.8 in , and ideally should have 2 or more square inches of 2 oz.2 Additional copper area improves the thermal characteristics, but with copper areas greater than approximately 6 in , only small improvements in heat dissipation are realized. If further thermal improvements are needed, double sided, multilayer PC board with large copper areas and/or airflow are recommended. The TS2496 (TO-263-5L package) junction temperature rise above ambient temperature with a 2A load for various input and output voltages. This data was taken with the circuit operating as a buck switching regulator with all components mounted on a PC board to simulate the junction temperature under actual operating conditions. This curve can be used for a quick check for the approximate junction temperature for various conditions, but be aware that there are many factors that can affect the junction temperature. When load currents higher than 2A are used, double sided or multilayer PC boards with large copper areas and/or airflow might be needed, especially for high ambient temperatures and high output voltages. For the best thermal performance, wide copper traces and generous amounts of printed circuit board copper should be used in the board layout. (Once exception to this is the output (switch) pin, which should not have large areas of copper.) Large areas of copper provide the best transfer of heat (lower thermal resistance) to the surrounding air, and moving air lowers the thermal resistance even further. 5/7 Version: C07 TS2496 2A / 150KHz Buck Switching Regulator TO-263-5L Mechanical Drawing DIM A B C D E F G H I J TO-263-5L DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 10.220 10.260 0.402 0.404 14.600 15.870 0.575 0.625 0.750 0.770 0.030 0.030 1.573 1.827 0.062 0.072 4.560 4.570 0.179 0.180 1.240 1.270 0.049 0.050 2.280 2.790 0.090 0.110 0.280 0.320 0.011 0.013 8.240 8.280 0.324 0.326 1.540 1.800 0.060 0.071 Marking Diagram Y M = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) L = Lot Code XXX = Voltage Code (3.3=3.3V, 5.0=5V) = Package Code for Adjustable type (CM5 = TO-263-5L) 6/7 Version: C07 TS2496 2A / 150KHz Buck Switching Regulator Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 7/7 Version: C07