FR2A THRU FR2K SURFACE MOUNT ULTRAFAST RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 2.0 Amperes FEATURES l For surface mounted applications l Low profile package l l Built-in strain relief Easy pick and place l l Fast recovery times for high efficiency Plastic package has Underwriters Laboratory l Flammability Classification 94V-O Glass passivated junction l SMB/DO-214AA High temperature soldering: 260 ¢J /10 seconds at terminals MECHANICAL DATA Case: JEDEC DO-214AA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard packaging: 12mm tape (EIA-481) Weight: 0.003 ounce, 0.093 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Resistive or inductive load. For capacitive load, derate current by 20%. Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at TL=90 ¢J Peak Forward Surge Current 8.3ms single half sinewave superimposed on rated load(JEDEC method) Maximum Instantaneous Forward Voltage at 2.0A Maximum DC Reverse Current TA=25 ¢J At Rated DC Blocking Voltage TA=125 ¢J Maximum Reverse Recovery Time (Note 1) TJ =25 ¢J Typical Junction capacitance (Note 2) Maximum Thermal Resistance (Note 3) Operating and Storage Temperature Range SYMBOLS FR2A FR2B FR2D FR2G FR2J FR2K VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 UNITS Volts Volts Volts 2.0 Amps IFSM 50.0 Amps VF IR 1.30 5.0 200 Volts £g A TRR CJ R £KJL TJ ,TSTG NOTES: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A 2. Measured at 1 MHz and Applied reverse voltage of 4.0 volts 150 250 40 20.0 -50 to +150 500 nS PF ¢J /W ¢J RATING AND CHARACTERISTIC CURVES PEAK FORWARD SURGE CURRENT, AMPERES FR2A THRU FR2K 2.0 AVERAGE FORWARD CURRENT, AMPERES 1.5 1.0 0.5 RESISTIVE OR INDUCTIVE LOAD P.C. BOARD MOUNTED ON 8.0mm 2 COPPER LAND AREAS 0 50 60 70 80 90 100 110 120 130 140 150 30 25 8.3ms SINGLE HALF SINE WAVE JEDEC METHOD 20 15 10 5 1 LEAD TEMPERATURE 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz Fig. 1-FORWARD CURRENT DERATING CURVE Fig. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT TYPICAL 1 T J = 25 ¢J 0.1 0.01 0 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 1FM, Apk 10 100 TA = 125 ¢J 10 1.0 T A = 25 ¢J 0.1 0 .2 .4 .6 .8 1.0 1.2 20 40 60 80 100 120 140 1.4 1.6 PERCENT OF RATED PEAK REVERSE VOLTAGE, % Fig. 3-FORWARD CHARACTERISTICS Fig. 4-TYPICAL REVERSE CHARACTERISTICS CAPACITANCE, pF 100 trr +0.5A 50 0 -0.25 10 5 1 5 10 50 REVERSE VOLTAGE, VOLTS Fig. 5-TYPICAL JUNCTION CHARACTERISTICS 100 NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. Source Impedance = 50 Ohms -1.0 SET TIME BASE FOR 50 ns/cm 1cm Fig. 6-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM