VISHAY SMCJ78A

SMCJ5.0A thru SMCJ188CA
www.vishay.com
Vishay General Semiconductor
Surface Mount TRANSZORB® Transient Voltage Suppressors
FEATURES
• Low profile package
• Ideal for automated placement
• Glass passivated chip junction
• Available in uni-directional and bi-directional
• Excellent clamping capability
• Very fast response time
• Low incremental surge resistance
DO-214AB (SMC)
• Meets MSL level 1, per J-STD-020, LF maximum peak of
260 °C
• Compliant to RoHS Directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
• Halogen-free according to IEC 61249-2-21 definition
PRIMARY CHARACTERISTICS
VWM
5.0 V to 188 V
PPPM
1500 W
IFSM (uni-directional only)
200 A
TJ max.
150 °C
TYPICAL APPLICATIONS
Use in sensitive electronics protection against voltage
transients induced by inductive load switching and lighting
on ICs, MOSFET, signal lines of sensor units for consumer,
computer, industrial, and telecommunication.
MECHANICAL DATA
DEVICES FOR BI-DIRECTION APPLICATIONS
For bi-directional use C or CA suffix (e.g. SMCJ188CA).
Electrical characteristics apply in both directions.
Case: DO-214AB (SMCJ)
Molding compound meets UL 94 V-0 flammability rating
Base P/N-M3 - halogen-free, RoHS compliant, and
commercial grade
Terminals: Matte tin plated leads, solderable
J-STD-002 and JESD 22-B102
M3 suffix meets JESD 201 class 1A whisker test
per
Polarity: Color band denotes cathode end
MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)
PARAMETER
Peak pulse power dissipation with a 10/1000 μs waveform (fig. 1)
Peak pulse current with a 10/1000 μs waveform
Peak forward surge current 8.3 ms single half sine-wave uni-directional only
SYMBOL
VALUE
UNIT
(1)(2)
1500
W
IPPM
(1)
See next table
A
IFSM
(2)
PPPM
200
A
Power dissipation on infinite heatsink, TA = 50 °C
PD
6.5
W
Operating junction and storage temperature range
TJ, TSTG
- 55 to + 150
°C
Notes
(1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 °C per fig. 2
A
(2) Mounted on 0.31" x 0.31" (8.0 mm x 8.0 mm) copper pads to each terminal
Revision: 20-Dec-11
Document Number: 89331
1
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMCJ5.0A thru SMCJ188CA
www.vishay.com
Vishay General Semiconductor
ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
DEVICE MARKING
DEVICE TYPE
CODE
MODIFIED
“J” BEND LEAD
UNI
BI
(+)SMCJ5.0A (5)
GDE
GDE
(+)SMCJ6.0A
GDG
GDG
(+)SMCJ6.5A
GDK
BDK
(+)SMCJ7.0A
GDM
GDM
(+)SMCJ7.5A
GDP
BDP
(+)SMCJ8.0A
GDR
BDR
(+)SMCJ8.5A
GDT
BDT
(+)SMCJ9.0A
GDV
BDV
(+)SMCJ10A
GDX
BDX
(+)SMCJ11A
GDZ
GDZ
(+)SMCJ12A
GEE
BEE
(+)SMCJ13A
GEG
GEG
(+)SMCJ14A
GEK
BEK
(+)SMCJ15A
GEM
BEM
(+)SMCJ16A
GEP
GEM
(+)SMCJ17A
GER
GER
(+)SMCJ18A
GET
BET
(+)SMCJ20A
GEV
BEV
(+)SMCJ22A
GEX
BEX
(+)SMCJ24A
GEZ
BEZ
(+)SMCJ26A
GFE
BFE
(+)SMCJ28A
GFG
GFG
(+)SMCJ30A
GFK
BFK
(+)SMCJ33A
GFM
BFM
(+)SMCJ36A
GFP
BFP
(+)SMCJ40A
GFR
BFR
(+)SMCJ43A
GFT
BFT
(+)SMCJ45A
GFV
GFV
(+)SMCJ48A
GFX
GFX
(+)SMCJ51A
GFZ
GFZ
(+)SMCJ54A
GGE
GGE
(+)SMCJ58A
GGG
GGG
(+)SMCJ60A
GGK
GGK
(+)SMCJ64A
GGM
GGM
(+)SMCJ70A
GGP
GGP
(+)SMCJ75A
GGR
GGR
(+)SMCJ78A
GGT
GGT
(+)SMCJ85A
GGV
GGV
(+)SMCJ90A
GGX
GGX
(+)SMCJ100A
GGZ
GGZ
(+)SMCJ110A
GHE
GHE
(+)SMCJ120A
GHG
GHG
(+)SMCJ130A
GHK
GHK
(+)SMCJ150A
GHM
GHM
(+)SMCJ160A
GHP
GHP
(+)SMCJ170A
GHR
GHR
BREAKDOWN
VOLTAGE
VBR AT IT (1)
(V)
MIN.
6.40
6.67
7.22
7.78
8.33
8.89
9.44
10.0
11.1
12.2
13.3
14.4
15.6
16.7
17.8
18.9
20.0
22.2
24.4
26.7
28.9
31.1
33.3
36.7
40.0
44.4
47.8
50.0
53.3
56.7
60.0
64.4
66.7
71.1
77.8
83.3
86.7
94.4
100
111
122
133
144
167
178
189
MAX.
7.07
7.37
7.98
8.60
9.21
9.83
10.4
11.1
12.3
13.5
14.7
15.9
17.2
18.5
19.7
20.9
22.1
24.5
26.9
29.5
31.9
34.4
36.8
40.6
44.2
49.1
52.8
55.3
58.9
62.7
66.3
71.2
73.7
78.6
86.0
92.1
95.8
104
111
123
135
147
159
185
197
209
TEST
CURRENT
IT
(mA)
STAND-OFF
VOLTAGE
VWM
(V)
MAXIMUM
REVERSE
LEAKAGE
AT VWM
ID (μA) (3)
10
10
10
10
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
5.0
6.0
6.5
7.0
7.5
8.0
8.5
9.0
10
11
12
13
14
15
16
17
18
20
22
24
26
28
30
33
36
40
43
45
48
51
54
58
60
64
70
75
78
85
90
100
110
120
130
150
160
170
800
800
500
200
100
50
20
10
5.0
5.0
5.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
MAXIMUM
MAXIMUM
PEAK PULSE CLAMPING
SURGE
VOLTAGE AT
CURRENT
IPPM
IPPM (A) (2)
VC (V)
163.0
145.6
133.9
125.0
116.3
110.3
104.2
97.4
88.2
82.4
75.4
69.8
64.7
61.5
57.7
54.3
51.4
46.3
42.3
38.6
35.6
33.0
31.0
28.1
25.8
23.3
21.6
20.6
19.4
18.2
17.2
16.0
15.5
14.6
13.3
12.4
11.9
10.9
10.3
9.3
8.5
7.8
7.2
6.2
5.8
5.5
9.2
10.3
11.2
12.0
12.9
13.6
14.4
15.4
17.0
18.2
19.9
21.5
23.2
24.4
26.0
27.6
29.2
32.4
35.5
38.9
42.1
45.4
48.4
53.3
58.1
64.5
69.4
72.7
77.4
82.4
87.1
93.6
96.8
103
113
121
126
137
146
162
177
193
209
243
259
275
Notes
(1) Pulse test: t  50 ms
p
(2) Surge current waveform per fig. 3 and derate per fig. 2
(3) For bi-directional types having V
WM of 10 V and less, the ID limit is doubled
(4) All terms and symbols are consistent with ANSI/IEEE C62.35
(5) For the bi-directional SMCJ5.0CA, the maximum V
BR is 7.25 V
(6) V = 3.5 V at I = 25 A (uni-directional only)
F
F
(+) Underwriters laboratory recognition for the classification of protectors (QVGQ2) under the UL standard for safety 497B and file number
E136766 for both uni-directional and bi-directional devices
Revision: 20-Dec-11
Document Number: 89331
2
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMCJ5.0A thru SMCJ188CA
www.vishay.com
Vishay General Semiconductor
THERMAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
PARAMETER
SYMBOL
Typical thermal resistance, junction to ambient
RJA
Typical thermal resistance, junction to lead
VALUE
UNIT
75
°C/W
15
°C/W
(1)
RJL
Note
(1) Mounted on minimum recommended pad layout
ORDERING INFORMATION (Example)
PREFERRED P/N
UNIT WEIGHT (g)
PREFERRED PACKAGE CODE
BASE QUANTITY
DELIVERY MODE
SMCJ5.0A-M3/57T
0.211
57T
850
7" diameter plastic tape and reel
SMCJ5.0A-M3/9AT
0.211
9AT
3500
13" diameter plastic tape and reel
RATINGS AND CHARACTERISTICS CURVES
(TA = 25 °C unless otherwise noted)
150
10
1
0.31" x 0.31" (8.0 mm x 8.0 mm)
Copper Pad Areas
0.1
0.1 µs
TJ = 25 °C
Pulse Width (td)
is defined as the Point
where the Peak Current
decays to 50 % of IPPM
tr = 10 µs
Peak Value
IPPM
100
Half Value - IPP
IPPM
2
50
10/1000 µs Waveform
as defined by R.E.A.
td
0
1.0 µs
10 µs
100 µs
1.0 ms
10 ms
0
1.0
2.0
3.0
td - Pulse Width (s)
t - Time (ms)
Fig. 1 - Peak Pulse Power Rating Curve
Fig. 3 - Pulse Waveform
4.0
20 000
100
Measured at
Zero Bias
10 000
CJ - Junction Capacitance (pF)
Peak Pulse Power (PPP) or Current (IPP)
Derating in Percentage, %
IPPM - Peak Pulse Current, % IRSM
PPPM - Peak Pulse Power (kW)
100
75
50
25
0
1000
VR, Measured at
Stand-Off
Voltage VWM
100
Uni-Directional
Bi-Directional
TJ = 25 °C
f = 1.0 MHz
Vsig = 50 mVp-p
10
0
25
50
75
100
125
150
175
200
1
10
100
TJ - Initial Temperature (°C)
VWM - Reverse Stand-Off Voltage (V)
Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature
Fig. 4 - Typical Junction Capacitance
Revision: 20-Dec-11
400
Document Number: 89331
3
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMCJ5.0A thru SMCJ188CA
www.vishay.com
Vishay General Semiconductor
200
Peak Forward Surge Current (A)
Transient Thermal Impedance (°C/W)
100
10
1.0
0.1
0.001
100
TJ = TJ max.
8.3 ms Single Half Sine-Wave
10
0.01
0.1
1
10
100
1000
1
100
10
tp - Pulse Duration (s)
Number of Cycles at 60 Hz
Fig. 5 - Typical Transient Thermal Impedance
Fig. 6 - Maximum Non-Repetitive Forward Surge Current
Uni-Directional Only
PACKAGE OUTLINE DIMENSIONS in inches (millimeters)
DO-214AB (SMC J-Bend)
Mounting Pad Layout
Cathode Band
0.185 (4.69)
MAX.
0.126 (3.20)
0.246 (6.22)
0.220 (5.59)
0.114 (2.90)
0.126 (3.20)
MIN.
0.280 (7.11)
0.060 (1.52)
MIN.
0.260 (6.60)
0.012 (0.305)
0.006 (0.152)
0.320 REF.
0.103 (2.62)
0.079 (2.06)
0.060 (1.52)
0.030 (0.76)
0.008 (0.2)
0 (0)
0.320 (8.13)
0.305 (7.75)
Revision: 20-Dec-11
Document Number: 89331
4
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
1
Document Number: 91000