Features • • • • • • • • • • • • • Current-controlled Output Current Source, 3 Input Channels Two Selectable Outputs for Grounded Laser Diodes Output Current per Channel up to 250 mA Total Output Current to 300 mA (Minimum) Rise Time 1.0 ns, Fall Time 1.1 ns On-chip RF Oscillator Control of 2 Different Swings by Use of 2 external Resistors Oscillator Frequency Range from 200 MHz to 600 MHz Oscillator Swing to 100 mA Single 5V Power Supply Common Enable/Disable Input TTL/CMOS Control Signals Small PB-free QFN16 (4 mm × 4 mm) or SSO16 Package 3-channel Laser Driver with RF Oscillator and 2 Outputs T0806 Applications • DVD-ROM with CD-RW Capability (Combo Drives) • Combo Drives with CD and DVD Writing Capability Summary 1. Description The T0806 is a laser diode driver for the operation of two different grounded laser diodes for DVD-RAM (650 nm) and CD-RW (780 nm) drives. It includes three channels for three different optical power levels which are controlled by a separate IC. The read channel generates a continuous output level whereas channels 2 and 3 are provided as write channels with very fast switching speeds. Write current pulses are enabled when a low signal is applied to the NE pins. All channels are summed together and switched to one of the two outputs IOUTA or IOUTB by the select input SELA. Each channel can contribute up to 250 mA to the total output current of up to 300 mA. A total gain of 100 is provided between each reference current input and the selected output. Although the reference inputs are current inputs, voltage control is possible by using external resistors. An on-chip RF oscillator is provided to reduce laser mode hopping noise during read mode. Swing can be set independently for the two selectable outputs with two different resistors. Oscillation is enabled by a high signal at the ENOSC pin. Complete output current and oscillator switch-off is achieved by a low signal at the ENABLE input. Rev. 4522FS–DVD–11/05 Note: This is a summary document. A complete dorcument is available under NDA. For more information, please contact your local Atmel sales office. Figure 1-1. Block Diagram I3 NE3 Channel 3 I2 NE2 Channel 2 IR IOUTA IOUTB Read channel ENABLE ENOSC RF oscillator RF 2 RSA RSB SELA T0806 4522FS–DVD–11/05 T0806 2. Pin Configuration Figure 2-1. Pinning SSO16 IR 1 16 VCC1 I2 2 15 IOUTA I3 3 14 GND RF 4 13 RSA NE2 5 12 RSB NE3 6 11 IOUTB ENABLE 7 10 SELA ENOSC 8 9 VCC2 T0806 Table 2-1. Pin Description SSO16 Pin Symbol Type 1 IR Analog Input current, bias voltage approximately GND Function 2 I2 Analog Input current, bias voltage approximately GND 3 I3 Analog Input current, bias voltage approximately GND 4 RF Analog External resistor to GND sets oscillator frequency of oscillator A 5 NE2 Digital Digital control of channel 2 (low active) 6 NE3 Digital Digital control of channel 3 (low active) 7 ENABLE Digital Enables output current (high active) 8 ENOSC Digital Enables RF oscillator (high active) 9 VCC2 Supply +5V power supply for IOUT 10 SELA Digital High: selects IOUTA, RSA Low: selects IOUTB, RSB 11 IOUTB Analog Output current source B for laser diode 12 RSB Analog External resistor to GND sets swing of oscillator B 13 RSA Analog External resistor to GND sets swing of oscillator A 14 GND Supply Ground 15 IOUTA Analog Output current source A for laser diode 16 VCC1 Supply +5V power supply for IOUT and circuit 3 4522FS–DVD–11/05 Pinning QFN16 I2 IR VCC1 IOUTA Figure 2-2. 1 2 3 4 16 15 14 13 12 11 10 9 5 6 7 8 GND RSA RSB IOUTB ENABLE ENOSC VCC2 SELA I3 RF NE2 NE3 Table 2-2. 4 Pin Description QFN16 Pin Symbol Type Function 1 I3 Analog Input current, bias voltage approximately GND 2 RF Analog External resistor to GND sets oscillator frequency 3 NE2 Digital Digital control of channel 2 (low active) 4 NE3 Digital Digital control of channel 3 (low active) 5 ENABLE Digital Enables output current (high active) 6 ENOSC Digital Enables RF oscillator (high active) 7 VCC2 Supply +5V power supply for IOUT 8 SELA Digital High: selects IOUTA, RSA Low: selects IOUTB, RSB 9 IOUTB Analog Output current source B for laser diode 10 RSB Analog External resistor to GND sets swing of oscillator B 11 RSA Analog External resistor to GND sets swing of oscillator A 12 GND Supply Ground 13 IOUTA Analog Output current source A for laser diode 14 VCC1 Supply +5V power supply for IOUT and circuit 15 IR Analog Input current, bias voltage approximately GND 16 I2 Analog Input current, bias voltage approximately GND Paddle GND Supply Ground T0806 4522FS–DVD–11/05 T0806 3. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Symbol Value Unit Supply voltage VCC –0.5 to +6.0 V Input voltage at IR, I2, I3 VIN1 –0.5 to +1.0 V Input voltage at NE2, NE3, ENOSC VIN2 –0.5 to VCC +0.5 V Output voltage VOUT –0.5 to VCC –1 V Total output current IOUT 350 mA Output current per channel Power dissipation Junction temperature Storage temperature range Notes: 300 IOUT (IR, I2, I3) mA (2) W TJ 150 °C TStg –65 to +125 °C Symbol Value Unit RthJA 135 K/W Symbol Value Unit VCC 4.5 to 5.5 V IIR/II2/II3 < 3.0 mA RF >3 kΩ RSA, RSB >1 kΩ Tamb 0 to +70 °C PMAX (1) 0.7 to 1 1. RthJA ≤115 K/W, Tamb = 70° C 2. RthJA ≤115 K/W, Tamb = 25° C 4. Thermal Resistance Parameters Junction ambient 5. Recommended Operating Conditions Parameters Supply voltage range Input current External resistor to GND to set oscillator frequency External resistor to GND to set oscillator swing Operating temperature range 5 4522FS–DVD–11/05 6. Ordering Information Extended Type Number Package Remarks T0806-TCQG SSO16 Taped and reeled, Pb-free T0806-PEQG Pb-free QFN16 (4 mm × 4 mm) Taped and reeled, Pb-free 7. Package Information 6 T0806 4522FS–DVD–11/05 T0806 7 4522FS–DVD–11/05 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © Atmel Corporation 2005. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are ® and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 4522FS–DVD–11/05