LINER RH1086M_1

RH1086M
0.5A and 1.5A Low Dropout
Positive Adjustable Regulators
DESCRIPTION
ABSOLUTE MAXIMUM RATINGS
The RH1086M positive adjustable regulator is designed to
provide 0.5A for the H package and 1.5A for the K package
with higher efficiency than currently available devices. All
internal circuitry is designed to operate down to 1V inputoutput differential and the dropout voltage is fully specified
as a function of load current. Dropout is guaranteed at a
maximum of 1.5V at maximum output current, decreasing
at lower load currents. On-chip trimming adjusts the output
voltage to 1%. Current limit is also trimmed, minimizing
the stress on both the regulator and power source circuitry
under overload conditions.
(Note 1)
The RH1086M is pin compatible with older 3-terminal
regulators. A 10μF output capacitor is required on this
new device. However, this is usually included in most
regulator designs.
Power Dissipation ............................... Internally Limited
Input-to-Output Voltage Differential ..........................25V
Operating Junction Temperature Range
Control Section ................................. – 55°C to 150°C
Power Transistor................................ –55°C to 200°C
Storage Temperature Range...................– 65°C to 150°C
Lead Temperature (Soldering, 10 sec) .................. 300°C
PRECONDITIONING
100% Thermal Limit Burn-In
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
The wafer lots are processed to Linear Technology Corporation’s in-house Class S flow-to-yield circuits usable
in stringent military applications.
BURN-IN CIRCUIT
RH1086M
IN
15V
OUT
ADJ
–15V
150Ω
RH1086 BI
CAPACITOR(S) NOT SHOWN
PACKAGE INFORMATION
BOTTOM VIEW
BOTTOM VIEW
VIN
ADJ
2
CASE
IS OUTPUT
2
INPUT
1
3
OUTPUT
(CASE)
1
ADJ
H PACKAGE
3-LEAD TO-39 METAL CAN
K PACKAGE
2-LEAD TO-3 METAL CAN
FINAL SPECIFICATIONS SUBJECT TO CHANGE
Note: For ordering information contact LTC.
rh1086mfc
1
RH1086M
TABLE 1: ELECTRICAL CHARACTERISTICS
PARAMETER
CONDITIONS
Reference Voltage
IOUT = 10mA, (VIN – VOUT) = 3V (K)
10mA ≤ IOUT ≤ IFULL LOAD,
1.5V ≤ (VIN – VOUT) ≤ 25V
Line Regulation
ILOAD = 10mA, 1.5V ≤ (VIN – VOUT) ≤ 15V
Load Regulation
(VIN – VOUT) = 3V,
10mA ≤ IOUT ≤ IFULL LOAD
Dropout Voltage
ΔVREF = 1%, IOUT = 1.5A (K)
ΔVREF = 1%, IOUT = 0.5A (H)
Current Limit
(VIN – VOUT) = 5V (K)
(VIN – VOUT) = 5V (H)
(VIN – VOUT) = 25V (K)
(VIN – VOUT) = 25V (H)
NOTES
6
(Preirradiation)
MIN
TA = 25°C
SUBTYP MAX GROUP
1.238
1.262
1.225
1.270
f = 120Hz, CADJ = 25μF,
COUT = 25μF Tantalum,
IOUT = IFULL LOAD, (VIN – VOUT) = 3V
Adjust Pin Current
TJ = 25°C
Adjust Pin Current
Change
10mA ≤ IOUT ≤ IFULL LOAD,
1.5V ≤ (VIN – VOUT) ≤ 15V
TA = 125°C, 1000 Hours
10Hz ≤ f ≤ 10kHz
Thermal Resistance
Junction-to-Case
Control Circuitry (K)
Control Circuitry (H)
Power Transistor (K)
Power Transistor (H)
1.270
2,3
V
1
0.2
2,3
%
2, 3, 6
0.3
1
0.4
2,3
%
4
4
1.5
1.25
1
1
1.5
1.25
2,3
2,3
V
V
2,3
2,3
2,3
2,3
A
A
A
A
2,3
mA
1.5
0.5
0.05
0.020
1
1
1
1
6
6
5
5
5
5
1
0.04
4
4
55
5
10
60
0.5
Long Term Stability
V
1.225
0.2
Temperature Stability
RMS Output Noise
(% of VOUT)
1
UNITS
2, 3
Minimum Load Current (VIN – VOUT) = 25V
Thermal Regulation
TA = 25°C, 30ms Pulse
Ripple Rejection
–55°C ≤ TA ≤ 125°C
SUBMIN
TYP MAX GROUP
1.5
0.5
0.05
0.020
10
%/W
60
5,6
dB
120
1
120
2,3
μA
5
1
5
2,3
μA
0.5
%
0.3
%
0.003
%
1.7
15.0
4.0
20.0
°C/W
°C/W
°C/W
°C/W
rh1086mfc
2
RH1086M
TABLE 1A: ELECTRICAL CHARACTERISTICS
PARAMETER
Reference Voltage
(Note 6)
CONDITIONS
10KRAD (Si)
MIN MAX
(Postirradiation) TA = 25°C, unless otherwise noted.
20KRAD (Si)
MIN MAX
50KRAD (Si)
MIN MAX
100KRAD (Si) 200KRAD (Si)
MIN MAX MIN MAX UNITS
IOUT = 10mA (VIN – VOUT) = 3V (K) 1.234 1.262
1.230 1.262 1.225 1.262 1.220 1.262 1.205 1.262
V
10mA ≤ IOUT ≤ IFULL LOAD
1.5V ≤ (VIN – VOUT) ≤ 15V
1.219 1.275 1.215 1.275 1.210 1.275
1.275
V
1.220 1.275
1.20
Line Regulation
(Notes 2, 3)
IOUT = 10mA
1.5V ≤ (VIN – VOUT) ≤ 15V
0.2
0.21
0.23
0.25
0.3
%
Load Regulation
(Notes 2, 3, 6)
(VIN – VOUT) = 3V
10mA ≤ IOUT ≤ IFULL LOAD
0.3
0.3
0.3
0.3
0.3
%
Dropout Voltage (Note 4)
ΔVREF = 1%, IOUT = 1.5A (K)
ΔVREF = 1%, IOUT = 0.5A (H)
1.5
1.25
1.51
1.26
1.52
1.27
1.55
1.29
1.575
1.32
V
V
Current Limit
(VIN – VOUT ) = 5V (K)
(VIN – VOUT ) = 25V (K)
(VIN – VOUT ) = 5V (H)
(VIN – VOUT ) = 25V (H)
Minimum Load Current
(VIN – VOUT ) = 25V
1.5
0.05
0.5
0.020
Adjust Pin Current
Adjust Pin Current Change 10mA ≤ IOUT ≤ IFULL LOAD
1.5V ≤ (VIN – VOUT) ≤ 15V
(Note 6)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: See thermal regulation specifications for changes in output voltage
due to heating effects. Line and load regulation are measured at a constant
junction temperature by low duty cycle pulse testing.
Note 3: Line and load regulation are guaranteed up to the maximum power
dissipation of 15W for RH1086MK and 3W for the RH1086MH. Power
dissipation is determined by the input/output differential voltage and
the output current. Guaranteed maximum power dissipation will not be
available over the full input/output voltage range.
1.5
0.049
0.5
0.019
1.5
0.048
0.5
0.019
1.5
0.047
0.5
0.018
1.5
0.045
0.5
0.017
A
A
A
A
10
10
10
10
10
mA
120
120
120
120
120
μA
5
5
5
5
5
μA
Note 4: Dropout voltage is specified over the full output current range of
the device. Test points and limits are shown on the Dropout Voltage curve
in the LT®1086 data sheet.
Note 5: Guaranteed by design, characterization, or correlation to other
tested parameters.
Note 6: IFULL LOAD is defined in the Current Limit curves in the standard
data sheet. For compliance with 883 revision C current density
specifications, the RH1086MK is derated to 1A.
rh1086mfc
3
RH1086M
TABLE 2: ELECTRICAL TEST REQUIREMENTS
MIL-STD-883 TEST REQUIREMENTS
SUBGROUP
Final Electrical Test Requirements (Method 5004)
1*,2,3,4,5,6
Group A Test Requirements (Method 5005)
1,2,3,4,5,6
Group C and D End Point Electrical Parameters
(Method 5005)
PDA Test Notes
The PDA is specified as 5% based on failures from group A, subgroup 1,
tests after cooldown as the final electrical test in accordance with method
5004 of MIL-STD-883 Class B. The verified failures of group A, subgroup 1,
after burn-in divided by the total number of devices submitted for burn-in
in that lot shall be used to determine the percent for the lot.
1
Linear Technology Corporation reserves the right to test to tighter limits
than those given.
*PDA applies to subgroup 1. See PDA Test Notes.
TOTAL DOSE BIAS CIRCUIT
15V
VIN
RH1086M
ADJ
VOUT
150Ω
–15V
RH1086 TA01
rh1086mfc
4
RH1086M
TYPICAL PERFORMANCE CHARACTERISTICS
Reference Voltage
Ripple Rejection
105
(VIN – VOUT) = 3V
IOUT = IFULL LOAD
100
95
RIPPLE REJECTION (dB)
1.25
1.24
1.23
CURRENT LIMIT (K PACKAGE) (A)
10mA ≤ IOUT ≤ IFULL LOAD
1.5V ≤ (VIN – VOUT) ≤ 15V
Current Limit
3.2
90
85
80
75
70
1.22
65
1
10
100
TOTAL DOSE – KRADS (Si)
1000
10
100
TOTAL DOSE – KRADS (Si)
2.2
2.0
0.6
1.8
1
1000
10
100
TOTAL DOSE – KRADS (Si)
0.065
0.12
0.060
0.11
0.055
1000
10
100
TOTAL DOSE – KRADS (Si)
Load Regulation
0.1
0
0.05
0
–0.05
–0.10
1
10
100
TOTAL DOSE – KRADS (Si)
RH1086 G04
1000
1.1
1.0
Minimum Load Current
4
(VIN – VOUT) = 3V
10mA ≤ IOUT ≤ IFULL LOAD
MINIMUM LOAD CURRENT (mA)
ADJUST PIN CURRENT (μA)
IOUT = 1.5A
70
60
50
40
10
100
TOTAL DOSE – KRADS (Si)
1000
RH1086 G07
1000
RH1086 G06
Adjust Pin Current
80
1.2
10
100
TOTAL DOSE – KRADS (Si)
1
RH1086 G05
Dropout Voltage
1.4
(VIN – VOUT) = 3V
10mA ≤ IOUT ≤ 1.5A
1.5V ≤ (VIN – VOUT) ≤ 15V
IOUT = 10mA
0.2
–0.1
1000
RH1086 G03
LOAD REGULATION (%)
0.13
LINE REGULATION (%)
CURRENT LIMIT (K PACKAGE) (A)
0.070
DROPOUT VOLTAGE (V)
0.8
2.4
0.10
0.3
CURRENT LIMIT (H PACKAGE) (A)
0.14
1
2.6
Line Regulation
0.075
(VIN – VOUT) = 25V
1.6
2.8
RH1086 G02
Current Limit
1
1.0
1.6
1
RH1086 G01
0.15
(VIN – VOUT) = 5V
3.0
CURRENT LIMIT (H PACKAGE) (A)
OUTPUT VOLTAGE (V)
1.26
(VIN – VOUT) = 25V
3
2
1
0
1
10
100
TOTAL DOSE – KRADS (Si)
1000
1
RH1086 G08
10
100
TOTAL DOSE – KRADS (Si)
1000
RH1086 G09
rh1086mfc
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
5
RH1086M
REVISION HISTORY
(Revision history begins at Rev B)
REV
DATE
DESCRIPTION
B
10/10
Updated Reference Voltage vs Postirradiation Limits in Table 1A: Electrical Characteristics
PAGE NUMBER
C
4/11
Updated Dropout Voltage in Table 1 and Table 1A
3
2, 3
rh1086mfc
6
Linear Technology Corporation
ID No. 66-11-1086 • LT 0411 REV C • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 1995