ONSEMI NCP59300

NCP59300
3.0A, Very Low-Dropout
(VLDO) Fast Transient
Response Regulator series
http://onsemi.com
MARKING
DIAGRAMS
TAB
1
5
D2PAK
CASE 936A
Features
•
Applications
•
•
•
•
•
•
Consumer and Industrial Equipment Point of Regulation
Servers and Networking Equipment
FPGA, DSP and Logic Power supplies
Switching Power Supply Post Regulation
Battery Chargers
Functional Replacement for Industry Standard MIC29300,
MIC39300, MIC37300
© Semiconductor Components Industries, LLC, 2011
January, 2011 − Rev. 2
1
TAB
3
D2PAK3
CASE 936
y
593xx
AWLYWWG
1
xx
y
A
WL
Y
WW
G
GND
1
VOUT
Output Current in Excess of 3.0 A
300 mV Typical Dropout Voltage at 3.0 A
Adjustable and Fixed Output Voltage Options
Low Ground Current
Fast Transient Response
Stable with Ceramic Output Capacitor
Logic Compatible Enable and Error Flag Pins
Current Limit, Reverse Current and Thermal Shutdown Protection
Operation up to 13.5 V Input Voltage
NCV Prefix for Automotive and Other Applications Requiring
AEC−Q100 Qualified Site and Change Controls
These are Pb−Free Devices
1
VIN
•
•
•
•
•
•
•
•
•
•
y
593xx
AWLYWWG
EN
VIN
GND
VOUT
FLG/ADJ
The NCP59300 series are high precision, very low dropout
(VLDO), low ground current positive voltage regulators that are
capable of providing an output current in excess of 3.0 A with a typical
dropout voltage lower than 300 mV at 3.0 A load current. The devices
are stable with ceramic output capacitors. This series consists initially
of an Adjustable output voltage version, with fixed voltage versions
planned in the future.
The NCP59300 series can withstand up to 18 V max input voltage.
Internal protection features consist of output current limiting,
built−in thermal shutdown and reverse output current protection.
Logic level enable and error flag pins are available on the 5−pin
version.
The NCP59302 is an Adjustable voltage Device and is available in
D2PAK−5 package.
= Voltage Version
= P (NCP), V (NCV)
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
Publication Order Number:
NCP59300/D
NCP59300
TYPICAL APPLICATIONS
VIN = 3.0 V
+
CIN
NCP59300
VIN
VOUT
EN
FLG
VOUT = 2.5 V
100k
+
+
COUT
47 mF, Ceramic
GND
NCP59302
VIN
CIN
+
ADJ
R1
R2
+
COUT
47 mF, Ceramic
VOUT = 2.5 V
VOUT
CIN
EN
1.3 V
Figure 2. Adjustable Regulator
NCP59300
VIN
VOUT
GND
Figure 1. Fixed 2.5 Regulator with Error Flag
VIN = 3.0 V
VIN
+
COUT
47 mF, Ceramic
GND
Figure 3. Fixed 2.5 Regulator in D2PAK−3 Package
PIN FUNCTION DESCRIPTION
Pin Number
D2PAK−5
Pin Number
D2PAK−3
Pin Name
1
−
EN
Enable Input: CMOS and TTL logic compatible. Logic high = enable; Logic low =
shutdown.
2
1
VIN
Input voltage which supplies both the internal circuitry and the current to the output
load
3
2
GND
Ground
TAB
TAB
TAB
TAB is connected to ground.
4
3
VOUT
5 (Fixed)
−
FLG
Error Flag Open collector output.
Active−low indicates an output fault condition.
5 (Adj)
−
ADJ
Adjustable Regulator Feedback Input.
Connect to output voltage resistor divider central node.
Pin Function
Linear Regulator Output.
http://onsemi.com
2
NCP59300
ABSOLUTE MAXIMUM RATINGS
Value
Unit
VIN
Symbol
Supply Voltage
Rating
0 to 18
V
VEN
Enable Input Voltage
0 to 18
V
VFLG
Error Flag open collector output Max. voltage
0 to 6.5
V
VOUT –
VIN
Reverse VOUT – VIN Voltage
0 to 6.5
V
PD
Power Dissipation (Notes 1 and 4)
Internally Limited
TJ
Junction Temperature
–40 v TJ v +125
°C
TS
Storage Temperature
–65 v TJ v +150
°C
2000
200
V
ESD Rating (Notes 2 and 3)
Human Body Model
Machine Model
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
NOTE: All voltages are referenced to GND pin unless otherwise noted.
1. PD(max) = (TJ(max) – TA) / RqJA, where RqJA depends upon the printed circuit board layout.
2. Devices are ESD sensitive. Handling precautions recommended..
3. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model (HBM) tested per AEC*Q100*002 (EIA/JESD22*A114C)
ESD Machine Model (MM) tested per AEC*Q100*003 (EIA/JESD22*A115C)
This device contains latch*up protection and exceeds 100 mA per JEDEC Standard JESD78.
4. This protection is not guaranteed outside the Recommended Operating Conditions.
RECOMMENDED OPERATING CONDITIONS (Note 5)
Symbol
Rating
Value
Unit
2.24 to 13.5
V
VIN
Supply Voltage
VEN
Enable Input Voltage
0 to 13.5
V
TJ
Junction Temperature
–40 v TJ v +125
°C
5. The device is not guaranteed to function outside it’s Recommended operating conditions.
http://onsemi.com
3
NCP59300
ELECTRICAL CHARACTERISTICS
TJ = 25°C with VIN = VOUT nominal + 1 V; VEN = VIN; IL = 10 mA; bold values indicate –40°C < TJ < +125°C, unless noted.
Conditions
Parameter
Output Voltage Accuracy
Min
Typ
Max
Unit
IL = 10 mA
−1
+1
%
10 mA < IOUT < 3 A , VOUT nominal + 1 v VIN v 13.5 V
−2
+2
%
0.5
%
Output Voltage Line Regulation
VIN = VOUT nominal + 1.0 V to 13.5 V; IL = 10 mA
0.02
Output Voltage Load Regulation
IL = 10 mA to 3 A
0.2
1
%
VIN – VOUT Dropout Voltage
(Note 6)
IL = 1.5 A
175
350
mV
IL = 3 A
300
500
mV
Ground Pin Current (Note 7)
IL = 3 A
60
90
120
mA
Ground Pin Current in Shutdown
VEN v 0.5 V
1.0
5
mA
Overload Protection Current Limit
VOUT = 0 V (Note 9)
3.5
5
A
Start−up Time
VEN = VIN, VOUT nominal = 2.5 V, IOUT = 10 mA,
COUT = 47 mF
100
500
ms
ENABLE INPUT
Enable Input Signal Levels
Regulator enable
V
1.8
Regulator shutdown
Enable pin Input Current
VEN v 0.8 V (Regulator shutdown)
6.5 V > VEN w 1.8 V (Regulator enable)
1
15
0.8
V
2
4
mA
30
40
mA
1
2
mA
400
500
mV
FLAG OUTPUT
Iflg(leak)
Voh = 6 V
VFLG(LO)
VIN = 2.24 V, IFLG = 250 mA (Note 8)
VFLG
Low Threshold, % of VOUT
210
95
%
Hysteresis
93
2
%
High Threshold, % of VOUT
97
99.2
%
1.240
1.252
1.265
V
100
200
350
nA
NCP59302 ONLY
1.228
1.215
Reference Voltage
Adjust Pin Bias Current
6. VDO = VIN – VOUT when VOUT decreases to 98% of its nominal output voltage with VIN = VOUT + 1 V. For output voltages below 1.74 V, dropout
voltage specification does not apply due to a minimum input operating voltage of 2.24 V.
7. IIN = IGND + IOUT.
8. For a 2.5 V device, VIN = 2.240 V (device is in dropout).
9. Device Power−on or Enable Start−up with output shorted to GND.
Package
Conditions / PCB Footprint
D2PAK–3, Junction−to−Case
RqJC = 2.1°C/W
D2PAK–5, Junction−to−Case
D2PAK–3, Junction−to−Air
D2PAK–5, Junction−to−Air
Thermal Resistance
RqJC = 2.1°C/W
PCB with 100
mm2
2.0 oz Copper Heat Spreading Area
RqJA = 52°C/W
PCB with 100
mm2
2.0 oz Copper Heat Spreading Area
RqJA = 52°C/W
http://onsemi.com
4
NCP59300
TYPICAL CHARACTERISTICS
TJ = 25°C if not otherwise noted
100
100
90
90
80
80
70
COUT = 100 mF
Ceramic
60
PSRR (dB)
PSRR (dB)
70
50
40
COUT = 47 mF
Ceramic
30
50
40
COUT = 47 mF
Ceramic
30
20
VIN = 3.5 V
10 VOUT = 2.5 V, IOUT = 3 A,
CIN = 0
0
10
100
1000
10k
FREQUENCY (Hz)
COUT = 100 mF
Ceramic
60
20
100k
VIN = 3.5 V
10 VOUT = 2.5 V, IOUT = 1 A,
CIN = 0
0
10
100
1000
10k
FREQUENCY (Hz)
1M
Figure 4. Power Supply Rejection Ratio
450
VOUTnom = 2.5 V
450
DROPOUT (mV)
DROPOUT (mV)
350
350
300
250
200
150
300
250
200
150
100
100
50
50
0
0.0
0.5
1.0
1.5
2.0
2.5
0
−50
3.0
−30
−10
10
30
50
70
90
110
OUTPUT CURRENT (A)
TEMPERATURE (°C)
Figure 6. Dropout Voltage vs. Output Current
Figure 7. Dropout Voltage vs. Temperature
130
3.0
1.4
10 mA
2.5
1A
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
VOUTnom = 2.5 V
IOUT = 3 A
400
400
3A
1.0
0.8
0.6
2A
0.4
0.2
0
1
1M
Figure 5. Power Supply Rejection Ratio
500
1.2
100k
1.2
1.4
1.6
SUPPLY VOLTAGE (V)
1.8
2.0
3A
1.5
1.0
2A
0.5
0.0
2
10 mA
1A
1
Figure 8. Dropout Characteristics (1.24 V)
1.2
1.4
1.6 1.8 2
2.2 2.4 2.6
SUPPLY VOLTAGE (V)
2.8
Figure 9. Dropout Characteristics (2.5 V)
http://onsemi.com
5
3
NCP59300
TYPICAL CHARACTERISTICS
TJ = 25°C if not otherwise noted
1.4
VIN = 2.24 V
VOUT = 1.24 V
50
1.2
GROUND CURRENT (mA)
GROUND CURRENT (mA)
60
40
30
20
10
0
0
0.5
1
1.5
2
OUTPUT CURRENT (A)
2.5
1
0.8
0.6
0.4
0.2
0
3
10 mA
0
Figure 10. Ground Current vs. Output Current
0.5
1
1.5
2
2.5
3
3.5
SUPPLY VOLTAGE (V)
4
4.5
5
Figure 11. Ground Current vs. Supply Voltage
(1.24 V)
2.5
120
60
3A
40
2A
20
1A
0
GROUND CURRENT (mA)
GROUND CURRENT (mA)
80
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
2
1.5
1
0.5
0
5
1
1.5
2
2.5
3
3.5
4
4.5
5
Figure 12. Ground Current vs. Supply Voltage
(1.24 V)
Figure 13. Ground Current vs. Supply Voltage
(2.5 V)
1.4
120
1.2
100
3A
80
60
40
2A
20
1A
0
0.5
SUPPLY VOLTAGE (V)
140
0
0
SUPPLY VOLTAGE (V)
GROUND CURRENT (mA)
GROUND CURRENT (mA)
10 mA
100
1
2
3
SUPPLY VOLTAGE (V)
4
1
0.8
0.6
0.4
0.2
0
−50
5
VIN = 3.5 V
VOUT = 2.5 V, IOUT = 10 mA
−30
−10
10
30
50
70
TEMPERATURE (°C)
Figure 14. Ground Current vs. Supply Voltage
(2.5 V)
90
110
Figure 15. Ground Current vs. Temperature
http://onsemi.com
6
130
NCP59300
TYPICAL CHARACTERISTICS
40
90
35
80
GROUND CURRENT (mA)
GROUND CURRENT (mA)
TJ = 25°C if not otherwise noted
30
25
20
15
10
5
0
−50
VIN = 3.5 V
VOUT = 2.5 V, IOUT = 1.5 A
−30
−10
70
60
50
40
30
20
10
10
30
50
70
TEMPERATURE (°C)
90
110
0
−50
130
Figure 16. Ground Current vs. Temperature
VIN = 3.5 V
VOUT = 2.5 V, IOUT = 3 A
−30
−10
10
30
50
70
TEMPERATURE (°C)
90
110
130
Figure 17. Ground Current vs. Temperature
2.6
22
ENABLE CURRENT (mA)
OUTPUT VOLTAGE (V)
20
2.55
2.5
2.45
2.4
−50
VOUTNOM = 2.5 V
IOUT = 10 mA
−30
−10
10
18
VEN = 6.5 V
16
14
12
10
8
6
4
VEN = 1.8 V
2
30
50
70
90
110
0
−50
130
−30
−10
10
30
50
70
90
110
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 18. Output Voltage vs. Temperature
Figure 19. Enable Pin Input Current vs.
Temperature
http://onsemi.com
7
130
NCP59300
FUNCTIONAL CHARACTERISTICS
Figure 20. Load Transient Response
Figure 21. Line Transient Response
Figure 22. Enable Transient Response
http://onsemi.com
8
NCP59300
APPLICATIONS INFORMATION
Output Capacitor and Stability
Thermal shutdown disables the NCP59300 device when
the die temperature exceeds the maximum safe operating
temperature.
When (VOUT – VIN) voltage difference is less than 6.5 V
in the application, the output structure of these regulators is
able to withstand output voltage (backup battery as
example) to be applied without reverse current flow. Of
course the additional current flowing through the internal
Feedback resistor divider at the NCP59300 Fix voltage
versions needs to be included in the backup battery
discharging calculations.
The NCP59300 series requires an output capacitor for
stable operation. The NCP59300 series is designed to
operate with ceramic output capacitors. The recommended
output capacitance value is 47 mF or greater. Such capacitors
help to improve transient response and noise reduction at
high frequency.
Input Capacitor
An input capacitor of 1.0 mF or greater is recommended
when the device is more than 4 inches away from the bulk
supply capacitance, or when the supply is a battery. Small,
surface−mount chip capacitors can be used for the
bypassing. The capacitor should be place within 1 inch of
the device for optimal performance. Larger values will help
to improve ripple rejection by bypassing the input of the
regulator, further improving the integrity of the output
voltage.
Adjustable Voltage Design
The NCP/NCV59302 Adjustable voltage Device Output
voltage is set by the ratio of two external resistors as shown
in Figure 23.
The device maintains the voltage at the ADJ pin at 1.24 V
referenced to ground. The current in R2 is then equal to
1.24 V / R2, and the current in R1 is the current in R2 plus
the ADJ pin bias current. The ADJ pin bias current flows
from VOUT through R1 into the ADJ pin.
The output voltage can be calculated using the formula
shown in Figure 23.
Minimum Load Current
The NCP59300 regulator is specified between finite
loads. A 10 mA minimum load current is necessary for
proper operation.
Error Flag
NCP59302
VIN
Some NCP59300 series members feature an error flag
circuit that monitors the output voltage and signals an error
condition when the voltage is 5% below the nominal output
voltage. The error flag is an open−collector output that can
sink up to 5 mA typically during a VOUT fault condition.
The FLG output is overload protected when a short circuit
of the pullup load resistor occurs in the application. This is
guaranteed in the full range of FLG output voltage Max
ratings (see Max Ratings table).
VIN
VOUT
VOUT
+
CIN
R1
EN
+
COUT
47 mF,
Ceramic
ADJ
GND
R2
ǒ
Ǔ
R1
) I ADJ @ R1
R2
Figure 23. Adjustable Voltage Operation
V OUT + 1.24 V @ 1 )
Enable Input
Some NCP59300 series members also feature an enable
input for on/off control of the device. It’s shutdown state
draws “zero” current from input voltage supply (only
microamperes of leakage). The enable input is TTL/CMOS
compatible for simple logic interface, but can be connected
up to VIN.
Thermal Considerations
The power handling capability of the device is limited by
the maximum rated junction temperature (125°C). The PD
total power dissipated by the device has two components,
Input to output voltage differential multiplied by Output
current and Input voltage multiplied by GND pin current.
Overcurrent and Reverse Output Current Protection
The NCP59300 regulator is fully protected from damage
due to output current overload conditions. When NCP59300
output is overloaded, Output Current limiting is provided.
This limiting is linear; output current during overload
conditions is constant. The device is also capable to
withstand power−on or enable start−up with output shorted
to ground for the full Recommended Operating Conditions
range. These features are advantageous for powering
FPGAs and other ICs having current consumption higher
than nominal during their startup.
P D + ǒV IN * V OUTǓ @ I OUT ) V IN @ I GND
(eq. 1)
The GND pin current value can be found in Electrical
Characteristics table and in Typical Characteristics graphs.
The Junction temperature TJ is
T J + T A ) P D @ R qJA
(eq. 2)
where TA is ambient temperature and RqJA is the Junction to
Ambient Thermal Resistance of the NCP/NCV59300
device mounted on the specific PCB.
http://onsemi.com
9
NCP59300
To maximize efficiency of the application and minimize
thermal power dissipation of the device it is convenient to
use the Input to output voltage differential as low as possible.
The static typical dropout characteristics for various
output voltage and output current can be found in the Typical
Characteristics graphs.
ORDERING INFORMATION
Output
Current
Output
Voltage
Junction Temp. Range
Package
Shipping†
NCP/NCV593xx
3.0 A
1.5 V
−40°C to +125°C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP/NCV593xx
3.0 A
1.65 V
−40°C to +125°C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP/NCV593xx
3.0 A
1.8 V
−40°C to +125°C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP/NCV593xx
3.0 A
2.5 V
−40°C to +125°C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP/NCV593xx
3.0 A
3.3 V
−40°C to +125°C
D2PAK−3
(Pb−Free)
Contact Sales Office
NCP/NCV593xx
3.0 A
1.5 V
−40°C to +125°C
D2PAK−5
(Pb−Free)
Contact Sales Office
NCP/NCV593xx
3.0 A
1.8 V
−40°C to +125°C
D2PAK−5
(Pb−Free)
Contact Sales Office
NCP/NCV593xx
3.0 A
2.5 V
−40°C to +125°C
D2PAK−5
(Pb−Free)
Contact Sales Office
NCP/NCV593xx
3.0 A
3.3 V
−40°C to +125°C
D2PAK−5
(Pb−Free)
Contact Sales Office
NCP59302DSADJR4G
3.0 A
ADJ
−40°C to +125°C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
NCV59302DSADJR4G
3.0 A
ADJ
−40°C to +125°C
D2PAK−5
(Pb−Free)
800 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
NCP59300
PACKAGE DIMENSIONS
D2PAK 5
CASE 936A−02
ISSUE D
TERMINAL 6
−T−
OPTIONAL
CHAMFER
A
U
U1
E
S
K
B
V
V1
H
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K.
4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING
SURFACE FOR TERMINAL 6.
5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR
GATE PROTRUSIONS. MOLD FLASH AND GATE
PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM.
1 2 3 4 5
M
D
0.010 (0.254)
G
M
P
N
T
DIM
A
B
C
D
E
G
H
K
L
M
N
P
R
S
U
V
U1
V1
L
R
C
SOLDERING FOOTPRINT*
8.38
0.33
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.067 BSC
0.539
0.579
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
5 _ REF
0.116 REF
0.200 MIN
0.250 MIN
0.297
0.305
0.038
0.046
1.702
0.067
10.66
0.42
16.02
0.63
3.05
0.12
SCALE 3:1
1.016
0.04
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
11
MILLIMETERS
MIN
MAX
9.804
10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
1.702 BSC
13.691
14.707
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
5 _ REF
2.946 REF
5.080 MIN
6.350 MIN
7.544
7.747
0.965
1.168
NCP59300
PACKAGE DIMENSIONS
D2PAK
CASE 936−03
ISSUE C
−T−
K
OPTIONAL
CHAMFER
A
TERMINAL 4
E
U
S
B
F
V
H
1
2
3
M
J
D
0.010 (0.254) M T
L
DIM
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
S
U
V
P
N
G
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS
A AND K.
4. DIMENSIONS U AND V ESTABLISH A MINIMUM
MOUNTING SURFACE FOR TERMINAL 4.
5. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH OR GATE PROTRUSIONS. MOLD FLASH
AND GATE PROTRUSIONS NOT TO EXCEED
0.025 (0.635) MAXIMUM.
R
SOLDERING FOOTPRINT*
C
10.49
8.38
INCHES
MIN
MAX
0.386
0.403
0.356
0.368
0.170
0.180
0.026
0.036
0.045
0.055
0.051 REF
0.100 BSC
0.539
0.579
0.125 MAX
0.050 REF
0.000
0.010
0.088
0.102
0.018
0.026
0.058
0.078
_
5 REF
0.116 REF
0.200 MIN
0.250 MIN
MILLIMETERS
MIN
MAX
9.804 10.236
9.042
9.347
4.318
4.572
0.660
0.914
1.143
1.397
1.295 REF
2.540 BSC
13.691 14.707
3.175 MAX
1.270 REF
0.000
0.254
2.235
2.591
0.457
0.660
1.473
1.981
_
5 REF
2.946 REF
5.080 MIN
6.350 MIN
16.155
2X
3.504
2X
1.016
5.080
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP59300/D