MAXIM MAX2121

19-5959; Rev 1; 7/12
KIT
ATION
EVALU
E
L
B
A
AVAIL
Complete Direct-Conversion L-Band Tuner
Applications
VSATs
Ordering Information
PART
MAX2121ETI+
TEMP RANGE
PIN-PACKAGE
-40°C to +85°C
28 TQFN-EP*
*EP = Exposed pad.
+Denotes a lead(Pb)-free/RoHS-compliant package.
VCC_RF2
VCC_BB
QDC-
QDC+
IDC-
+
SDA
Functional Diagram
SCL
The device directly converts the satellite signals from
the LNB to baseband using a broadband I/Q downconverter. The operating frequency range extends from
925MHz to 2175MHz.
The device includes an LNA and an RF variable-gain
amplifier, I and Q downconverting mixers, and baseband lowpass filters and digitally controlled baseband
variable-gain amplifiers. Together, the RF and baseband variable-gain amplifiers provide more than 80dB
of gain control range.
The device includes fully monolithic VCOs, as well as a
complete fractional-N frequency synthesizer.
Additionally, an on-chip crystal oscillator is provided
along with a buffered output for driving additional tuners
and demodulators. Synthesizer programming and device
configuration are accomplished with a 2-wire serial interface. The IC features a VCO autoselect (VAS) function
that automatically selects the proper VCO. For multituner
applications, the device can be configured to have one
of two 2-wire interface addresses. A low-power standby
mode is available whereupon the signal path is shut
down while leaving the reference oscillator, digital interface, and buffer circuits active, providing a method to
reduce power in single and multituner applications.
The device is the most advanced broadband/VSAT
DBS tuner available. The low noise figure eliminates the
need for an external LNA. A small number of passive
components are needed to form a complete broadband
satellite tuner DVB-S2 RF front-end solution. The tuner
is available in a very small, 5mm x 5mm, 28-pin thin
QFN package.
o 925MHz to 2175MHz Frequency Range
o Monolithic VCO
Low Phase Noise: -97dBc/Hz at 10kHz
No Calibration Required
o High Dynamic Range: -75dBm to 0dBm
o Integrated LP Filters: 123.75MHz
o Single +3.3V ±5% Supply
o Low-Power Standby Mode
o Address Pin for Multituner Applications
o Differential I/Q Interface
o I2C 2-Wire Serial Interface
o Very Small, 5mm x 5mm, 28-Pin TQFN Package
ADDR
The MAX2121 low-cost, direct-conversion tuner IC is
designed for satellite set-top and VSAT applications.
Features
28
27
26
25
24
23
22
1
DC OFFSET
CORRECTION
INTERFACE LOGIC
AND CONTROL
21
IDC+
MAX2121
VCC_RF1
2
20
IOUT-
GND
3
19
IOUT+
RFIN
4
18
QOUT-
GC1
5
17
QOUT+
VCC_LO
6
16
VCC_DIG
VCC_VCO
7
15
REFOUT
FREQUENCY
SYNTHESIZER
DIV2/DIV4
8
9
10
11
12
13
14
BYPVCO
TUNEVCO
GNDTUNE
GNDSYN
CPOUT
VCC_SYN
XTAL
EP
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX2121
General Description
MAX2121
Complete Direct-Conversion L-Band Tuner
ABSOLUTE MAXIMUM RATINGS
VCC_ to GND .........................................................-0.3V to +3.9V
All Other Pins to GND.................................-0.3V to (VCC + 0.3V)
RF Input Power: RFIN .....................................................+10dBm
BYPVCO, CPOUT, XTAL, REFOUT, IOUT_, QOUT_ , IDC_,
QDC_ to GND Short-Circuit Protection...............................10s
Continuous Power Dissipation (TA = +70°C)
TQFN (derate 34.5mW/°C above +70°C) ......................2.75W
Operating Temperature Range .............................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
CAUTION! ESD SENSITIVE DEVICE
DC ELECTRICAL CHARACTERISTICS
(MAX2121 Evaluation Kit: VCC_ = +3.13V to +3.47V, fXTAL = 27MHz, TA = -40°C to +85°C, VGC1 = +0.5V (max gain), default register
settings except BBG[3:0] = 1011. No input signals at RF, baseband I/Os are open circuited. Typical values measured at VCC =
+3.3V, TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
SUPPLY
Supply Voltage (VCC_)
Supply Current
3.3
3.47
Receive mode, bit STBY = 0
3.13
148
200
Standby mode, bit STBY = 1
3
mA
ADDRESS SELECT INPUT (ADDR)
Digital Input-Voltage High, VIH
2.4
V
Digital Input-Voltage Low, VIL
0.5
V
Digital Input-Current High, IIH
50
µA
Digital Input-Current Low, I IL
ANALOG GAIN-CONTROL INPUT (GC1)
Input Voltage Range
Maximum gain = 0.5V
Input Bias Current
-50
µA
0.5
2.7
V
-50
+50
µA
0.4
2.3
V
400
kHz
VCO TUNING VOLTAGE INPUT (TUNEVCO)
Input Voltage Range
2-WIRE SERIAL INPUTS (SCL, SDA)
Clock Frequency
0.7 x
VCC
Input Logic-Level High
V
Input Logic-Level Low
Input Leakage Current
Digital inputs = GND or VCC
±0.1
0.3 x
VCC
V
±1
µA
0.4
V
2-WIRE SERIAL OUTPUT (SDA)
Output Logic-Level Low
2
I SINK = 1mA (Note 2)
Complete Direct-Conversion L-Band Tuner
(MAX2121 Evaluation Kit: VCC = +3.13V to +3.47V, TA = -40°C to +85°C, default register settings except BBG[3:0] = 1111. Typical
values measured at VCC = +3.3V, TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
CONDITIONS
MIN
TYP
72
78
MAX
UNITS
MAIN SIGNAL PATH PERFORMANCE
Minimum Gain
f IN = 2175MHz
Gain Flatness
925MHz to 2175MHz (Note 2)
Input Frequency Range
(Note 3)
RF Gain-Control Range (GC1)
Baseband Gain-Control Range
0.5V < VGC1 < 2.7V
Bits BBG[3:0] = 1111 to 0000
In-Band Input IP3
(Note 4)
4
925
dB
6
dB
2175
MHz
65
73
dB
11.5
13.5
dB
+2
dBm
Out-of-Band Input IP3
(Note 5)
+15
dBm
Input IP2
(Note 6)
+40
dBm
8
Noise Figure
VGC1 is set to 0.5V (maximum RF gain) and BBG[3:0]
is adjusted to give a 1VP-P baseband output level for a
-75dBm CW input tone at 1500MHz
Starting with the same BBG[3:0] setting as above,
VGC1 is adjusted to back off RF gain by 10dB (Note 2)
9
dB
Minimum RF Input Return Loss
925MHz < fRF < 2175MHz, in 75 system
BASEBAND OUTPUT CHARACTERISTICS
12
12
0.5
dB
Nominal Output Voltage Swing
RLOAD = 200//5pF
I/Q Amplitude Imbalance
Measured at 500kHz
1
±1
VP-P
dB
I/Q Quadrature Phase Imbalance
Measured at 500kHz
3.5
Degrees
Single-Ended I/Q Output
Impedance
Real Z O, from 1MHz to 140MHz
24
Output 1dB Compression Voltage
Differential
3
VP-P
Baseband Highpass -3dB
Frequency Corner
47nF capacitors at IDC_, QDC_
400
Hz
BASEBAND LOWPASS FILTERS (5th-Order Butterworth with 1st-Order Group Delay Compensation)
Filter Bandwidth (-3dB)
123.75
MHz
Rejection Ratio
At 247.5MHz
31
dB
Group Delay
Up to 0.5dB bandwidth
1.0
ns
3dB Bandwidth Tolerance
±10
%
925
2175
MHz
RF-Divider Range (N)
19
251
Reference-Divider Frequency
Range
12
30
Reference-Divider Range (R)
1
1
Phase-Detector Comparison
Frequency
12
30
FREQUENCY SYNTHESIZER
RF-Divider Frequency Range
MHz
MHz
3
MAX2121
AC ELECTRICAL CHARACTERISTICS
MAX2121
Complete Direct-Conversion L-Band Tuner
AC ELECTRICAL CHARACTERISTICS (continued)
(MAX2121 Evaluation Kit: VCC = +3.13V to +3.47V, TA = -40°C to +85°C, default register settings except BBG[3:0] = 1111. Typical
values measured at VCC = +3.3V, TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
2175
MHz
VOLTAGE-CONTROLLED OSCILLATOR AND LO GENERATION
Guaranteed LO Frequency Range
LO Phase Noise
925
f OFFSET = 10kHz
-97
f OFFSET = 100kHz
-100
f OFFSET = 1MHz
-122
dBc/Hz
XTAL/REFERENCE OSCILLATOR INPUT AND OUTPUT BUFFER
XTAL Oscillator Frequency
Range f XTAL
Parallel-resonance-mode crystal (Note 7)
12
Input Overdrive Level
AC-coupled sine-wave input
0.5
XTAL Output-Buffer Divider
Range
XTAL Output Voltage Swing
XTAL Output Duty Cycle
1
1
12MHz to 30MHz, CLOAD = 10pF
1
30
MHz
2.0
VP-P
8
1.5
50
2
VP-P
%
Note 1: Min/max values are production tested at TA = +25°C. Min/max limits at TA = -40°C and TA = +85°C are guaranteed by
design and characterization.
Note 2: Guaranteed by design and characterization at TA = +25°C.
Note 3: Input gain range specifications met over this band.
Note 4: In-band IIP3 test conditions: GC1 set to provide the nominal baseband output drive when mixing down a -23dBm tone at
2175MHz to 5MHz baseband (fLO = 2170MHz). Baseband gain is set to its default value (BBG[3:0] = 1011). Two tones at
-26dBm each are applied at 2174MHz and 2175MHz. The IM3 tone at 3MHz is measured at baseband, but is referred to the
RF input.
Note 5: Out-of-band IIP3 test conditions: GC1 set to provide nominal baseband output drive when mixing down a -23dBm tone at
2175MHz to 5MHz baseband (fLO = 2170MHz). Baseband gain is set to its default value (BBG[3:0] = 1011). Two tones at
-20dBm each are applied at 1919MHz and 1663MHz. The IM3 tone at 5MHz is measured at baseband, but is referred to the
RF input.
Note 6: Input IP2 test conditions: GC1 set to provide nominal baseband output drive when mixing down a -23dBm tone at 2175MHz
to 5MHz baseband (fLO = 2170MHz). Baseband gain is set to its default value (BBG[3:0] = 1011). Two tones at -20dBm
each are applied at 925MHz and 1250MHz. The IM2 tone at 5MHz is measured at baseband, but is referred to the RF input.
Note 7: See Table 16 for crystal ESR requirements.
4
Complete Direct-Conversion L-Band Tuner
150
145
140
TA = -40°C
135
TA = +85°C
2.0
TA = -40°C
1.5
130
1.0
125
3.3
3.4
MAX2121 toc03
-45
-50
-55
3.2
3.3
3.4
3.5
1.0
1.5
2.0
3.0
2.5
QUADRATURE PHASE ERROR
vs. BASEBAND FREQUENCY
1.0
TA = +85°C
0.8
TA = +25°C
0.6
0.4
TA = +85°C
0.2
TA = -40°C
3.5
0
1150
1400
1650
1900
2150
TA = +85°C
TA = -40°C
0
1
10
BASEBAND FREQUENCY (MHz)
100
1150
1400
1650
1900
1.0
0.5
2150
0.1
1
100
10
BASEBAND FREQUENCY (MHz)
0
-5
-10
-15
-20
-25
-30
-35
-40
-45
-50
-55
-60
-65
MAX2121 toc08
BASEBAND OUTPUT LEVEL (dB)
MAX2121 toc07
0.4
0.2
TA = +25°C
1.5
BASEBAND FILTER FREQUENCY RESPONSE
BASEBAND FILTER FREQUENCY RESPONSE
TA = +25°C
0.6
TA = +85°C
2.0
LO FREQUENCY (MHz)
QUADRATURE MAGNITUDE MATCHING
vs. BASEBAND FREQUENCY
0.8
TA = -40°C
2.5
0
900
LO FREQUENCY (MHz)
fLO = 1425MHz
fLO = 1425MHz
3.0
1
MAX2121 toc09
TA = +25°C
0.5
fBASEBAND = 50MHz
QUADRATURE PHASE ERROR (DEG)
1.5
1.0
MAX2121 toc05
QUADRATURE MAGNITUDE MATCHING
vs. LO FREQUENCY
0
QUADRATURE MAGNITUDE MATCHING (dB)
-40
QUADRATURE PHASE ERROR
vs. LO FREQUENCY
TA = -40°C
0.1
-35
VOUT (VP-P)
2.5
1.0
-30
SUPPLY VOLTAGE (V)
3.0
900
-25
SUPPLY VOLTAGE (V)
fBASEBAND = 50MHz
2.0
-20
-60
3.1
3.5
QUADRATURE MAGNITUDE MATCHING (dB)
QUADRATURE PHASE ERROR (DEG)
3.5
3.2
MAX2121 toc04
3.1
-15
MAX2121 toc06
TA = +25°C
BASEBAND 3RD-ORDER HARMONIC (dBc)
155
2.5
-10
0
BASEBAND OUTPUT LEVEL (dB)
SUPPLY CURRENT (mA)
160
MAX2121 toc02
TA = +85°C
165
3.0
STANDBY SUPPLY CURRENT (mA)
170
MAX2121 toc01
175
-1
-2
-3
-4
-5
TA = +25°C
-6
-7
-8
-9
-10
0
100
200
300
400
BASEBAND FREQUENCY (MHz)
500
0
25
50
75
100
125
150
BASEBAND FREQUENCY (MHz)
5
MAX2121
Typical Operating Characteristics
(MAX2121 Evaluation Kit: VCC = +3.3V, TA = +25°C, baseband output frequency = 5MHz, VGC1 = +1.2V, default register settings
except BBG[3:0] = 1011, unless otherwise noted.)
STANDBY SUPPLY CURRENT
SUPPLY CURRENT vs. SUPPLY VOLTAGE
vs. SUPPLY VOLTAGE
HD3 vs. VOUT
Typical Operating Characteristics (continued)
(MAX2121 Evaluation Kit: VCC = +3.3V, TA = +25°C, baseband output frequency = 5MHz, VGC1 = +1.2V, default register settings
except BBG[3:0] = 1011, unless otherwise noted.)
0
-0.25
-0.50
-0.75
MAX2121 toc11
-2
-3
-4
-5
-6
-7
0
20
40
60
10
0
100
80
9.5
10dB BACKED OFF GAIN
8.5
30
ADJUST BBG[3:0] for 1VP-P
BASEBAND OUTPUT WITH PIN = -75dBm
AND VGC1 = -0.5V, fLO = 1500MHz
7.0
25
20
15
2150
10
0
-10
-20
-30
-65
-75
LO FREQUENCY (MHz)
-55
-45
-75
-35
-65
IN-BAND IIP3 vs. INPUT POWER
IIP2 vs. INPUT POWER
SEE NOTE 6 ON PAGE 4
FOR CONDITIONS
INPUT RETURN LOSS (dB)
30
0
25
IIP2 (dBm)
-10
-20
-30
20
15
10
5
-40
0
-50
-35
-25
-15
0
MAX2121 toc17
35
-45
-5
INPUT RETURN LOSS vs. FREQUENCY
40
MAX2121 toc16
SEE NOTE 4 ON PAGE 4 FOR CONDITIONS
10
-55
INPUT POWER (dBm)
INPUT POWER (dBm)
20
3.0
2.5
20
5
1900
2.0
SEE NOTE 5 ON PAGE 4 FOR CONDITIONS
10
7.5
1650
1.5
OUT-OF-BAND IIP3 vs. INPUT POWER
8.0
1400
1.0
30
OUT-OF-BAND IIP3 (dBm)
MAX2121 toc13
35
NOISE FIGURE (dB)
NOISE FIGURE (dB)
ADJUST BBG[3:0] FOR 1VP-P BASEBAND
OUTPUT WITH PIN = -75dBm AND VGC1 = 0.5V
1150
0.5
VGC1 (V)
NOISE FIGURE vs. INPUT POWER
11.0
-5
VGC1 = 0.5V
-10
-15
-20
-5
-60
-10
-75
-65
-55
-45
-35
-25
INPUT POWER (dBm)
6
0
10,000
1000
BASEBAND FREQUENCY (Hz)
NOISE FIGURE vs. LO FREQUENCY
(TA = +25°C)
900
30
20
TEMPERATURE (°C)
9.0
40
MAX2121 toc18
-20
50
-8
-10
-40
10.0
BBG[3:0] = 1111
60
-9
-1.00
10.5
70
MAX2121 toc15
0.25
-1
VOLTAGE GAIN (dB)
0.50
80
MAX2121 toc14
BASEBAND GAIN ERROR AT f-3dB (dB)
NORMALIZED AT TA = +25°C
0.75
VOLTAGE GAIN vs. VGC1
0
BASEBAND OUTPUT LEVEL (dB)
MAX2121 toc10
1.00
BASEBAND FILTER HIGHPASS
FREQUENCY RESPONSE
MAX2121 toc12
BASEBAND FILTER 3dB FREQUENCY
vs. TEMPERATURE
IN-BAND IIP3 (dBm)
MAX2121
Complete Direct-Conversion L-Band Tuner
-15
-5
VGC1 = 2.7V
-25
-75
-65
-55
-45
-35
-25
INPUT POWER (dBm)
-15
-5
900
1125
1350
1575
1800
FREQUENCY (MHz)
2025
2250
Complete Direct-Conversion L-Band Tuner
PHASE NOISE AT 10kHz OFFSET vs.
CHANNEL FREQUENCY
PHASE NOISE vs. OFFSET FREQUENCY
PHASE NOISE (dBc/Hz)
-95
-100
MAX2121 toc20
-90
MAX2121 toc19
PHASE NOISE AT 10kHz OFFSET (dBc/Hz)
-90
-100
-110
-120
fLO = 1800MHz
-130
1.0E+03
-105
925
1115 1305 1495 1685 1875 2065 2255
CHANNEL FREQUENCY (MHz)
1.0E+04
LO LEAKAGE vs. LO FREQUENCY
400
350
-75
SUB-BAND 23
300
KV (MHz/V)
LO LEAKAGE (dBm)
MAX2121 toc22
MEASURED AT RF INPUT
VCO: KV vs. VTUNE
450
MAX2121 toc21
-70
1.0E+06
1.0E+05
OFFSET FREQUENCY (Hz)
-80
250
200
SUB-BAND 12
150
-85
100
50
-90
SUB-BAND 0
0
925
1175
1425
1675
1925
LO FREQUENCY (MHz)
2175
0
0.5
1.0
1.5
2.0
VTUNE (V)
2.5
3.0
7
MAX2121
Typical Operating Characteristics (continued)
(MAX2121 Evaluation Kit: VCC = +3.3V, TA = +25°C, baseband output frequency = 5MHz, VGC1 = +1.2V, default register settings
except BBG[3:0] = 1011, unless otherwise noted.)
Complete Direct-Conversion L-Band Tuner
SCL
SDA
VCC_BB
QDC-
QDC+
IDC-
TOP VIEW
ADDR
MAX2121
Pin Configuration
28
27
26
25
24
23
22
21
IDC+
2
20
IOUT-
3
19
IOUT+
VCC_RF2
1
VCC_RF1
GND
+
MAX2121
RFIN
4
18
QOUT-
GC1
5
17
QOUT+
VCC_LO
6
16
VCC_DIG
VCC_VCO
7
15
REFOUT
8
9
10
11
12
13
14
BYPVCO
TUNEVCO
GNDTUNE
GNDSYN
CPOUT
VCC_SYN
XTAL
EP
TQFN
(5mm x 5mm)
Pin Description
PIN
8
NAME
FUNCTION
1
VCC_RF2
DC Power Supply for LNA. Connect to a +3.3V low-noise supply. Bypass to GND with a 1nF capacitor
connected as close as possible to the pin. Do not share capacitor ground vias with other ground connections.
2
VCC_RF1
DC Power Supply for LNA. Connect to a +3.3V low-noise supply. Bypass to GND with a 1nF capacitor
connected as close as possible to the pin. Do not share capacitor ground vias with other ground connections.
3
GND
Ground. Connect to board’s ground plane for proper operation.
4
RFIN
Wideband 75 RF Input. Connect to an RF source through a DC-blocking capacitor.
5
GC1
RF Gain-Control Input. High-impedance analog input with a 0.5V to 2.7V operating range.
VGC1 = 0.5V corresponds to the maximum gain setting.
6
VCC_LO
DC Power Supply for LO Generation Circuits. Connect to a +3.3V low-noise supply. Bypass to GND
with a 1nF capacitor connected as close as possible to the pin. Do not share capacitor ground vias
with other ground connections.
7
VCC_VCO
DC Power Supply for VCO Circuits. Connect to a +3.3V low-noise supply. Bypass to GND with a 1nF
capacitor connected as close as possible to the pin. Do not share capacitor ground vias with other
ground connections.
Complete Direct-Conversion L-Band Tuner
PIN
NAME
FUNCTION
8
BYPVCO
Internal VCO Bias Bypass. Bypass to GND with a 100nF capacitor connected as close as possible to
the pin. Do not share capacitor ground vias with other ground connections.
9
TUNEVCO
High-Impedance VCO Tune Input. Connect the PLL loop filter output directly to this pin with as short of
a connection as possible.
10
GNDTUNE
Ground for TUNEVCO. Connect to the PCB ground plane.
11
GNDSYN
Ground for Synthesizer. Connect to the PCB ground plane.
12
CPOUT
Charge-Pump Output. Connect this output to the PLL loop filter input with the shortest
connection possible.
13
VCC_SYN
DC Power Supply for Synthesizer Circuits. Connect to a +3.3V low-noise supply. Bypass to GND with
a 1nF capacitor connected as close as possible to the pin. Do not share capacitor ground vias with
other ground connections.
14
XTAL
15
REFOUT
Crystal-Oscillator Buffer Output. A DC-blocking capacitor must be used when driving external circuitry.
16
VCC_DIG
DC Power Supply for Digital Logic Circuits. Connect to a +3.3V low-noise supply. Bypass to GND with
a 1nF capacitor connected as close as possible to the pin. Do not share capacitor ground vias with
other ground connections.
17
QOUT+
18
QOUT-
19
IOUT+
20
IOUT-
21
IDC+
22
IDC-
23
QDC+
24
QDC-
25
VCC_BB
26
SDA
2-Wire Serial-Data Interface. Requires 1k pullup resistor to VCC.
27
SCL
2-Wire Serial-Clock Interface. Requires 1k pullup resistor to VCC.
28
ADDR
—
EP
Crystal-Oscillator Interface. Use with an external parallel-resonance-mode crystal through a series
1nF capacitor. See the Typical Application Circuit.
Quadrature Baseband Differential Output. AC-couple with 47nF capacitors to the demodulator input.
In-Phase Baseband Differential Output. AC-couple with 47nF capacitors to the demodulator input.
I-Channel Baseband DC Offset Correction. Connect a 47nF ceramic chip capacitor from IDC- to IDC+.
Q-Channel Baseband DC Offset Correction. Connect a 47nF ceramic chip capacitor from QDC- to QDC+.
DC Power Supply for Baseband Circuits. Connect to a +3.3V low-noise supply. Bypass to GND with
a 1nF capacitor connected as close as possible to the pin. Do not share capacitor ground vias with
other ground connections.
Address. Must be connected to either ground (logic 0) or supply (logic 1).
Exposed Pad. Solder evenly to the board’s ground plane for proper operation.
9
MAX2121
Pin Description (continued)
MAX2121
Complete Direct-Conversion L-Band Tuner
Detailed Description
shows each bit name and the bit usage information for all
registers. Note that all registers must be written after and
no earlier than 100µs after the device is powered up. The
VCO autoselection circuit is triggered by writing to register 5. Thus register 5 should be the last register to be
written in order to ensure proper PLL lock.
Register Description
The MAX2121 includes 12 user-programmable registers
and two read-only registers. See Table 1 for register
configurations. The register configuration of Table 1
Table 1. Register Configuration
MSB
LSB
REG
REGISTER READ/
REG
NUMBER
NAME
WRITE ADDRESS
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
1
N-Divider
MSB
Write
0x00
FRAC
1
N[14]
N[13]
N[12]
N[11]
N[10]
N[9]
N[8]
2
N-Divider
LSB
Write
0x01
N[7]
N[6]
N[5]
N[4]
N[3]
N[2]
N[1]
N[0]
3
Charge
Pump
Write
0x02
CPMP[1]
0
CPMP[0]
0
CPLIN[1]
0
CPLIN[0]
1
F[19]
F[18]
F[17]
F[16]
4
F-Divider
MSB
Write
0x03
F[15]
F[14]
F[13]
F[12]
F[11]
F[10]
F[9]
F[8]
5
F-Divider
LSB
Write
0x04
F[7]
F[6]
F[5]
F[4]
F[3]
F[2]
F[1]
F[0]
6
XTAL
Buffer and
Reference
Divider
Write
0x05
XD[2]
XD[1]
XD[0]
R[4]
R[3]
R[2]
R[1]
R[0]
7
PLL
Write
0x06
D24
CPS
ICP
X
X
X
X
X
8
VCO
Write
0x07
VCO[4]
VCO[3]
VCO[2]
VCO[1]
VCO[0]
VAS
ADL
ADE
9
Lowpass
Filter
Write
0x08
10
Control
Write
0x09
STBY
X
PWDN
0
X
BBG[3]
11
Shutdown
Write
0x0A
X
PLL
0
DIV
0
VCO
0
BB
0
12
Test
Write
0x0B
CPTST[2]
0
CPTST[1]
0
CPTST[0]
0
X
TURBO
1
13
Status
Byte-1
Read
0x0C
POR
VASA
VASE
LD
X
14
Status
Byte-2
Read
0x0D
X = Don’t care.
10
DATA BYTE
10010111
BBG[2] BBG[1] BBG[0]
RFMIX RFVGA
0
0
FE
0
LD
LD
LD
MUX[2] MUX[1] MUX[0]
0
0
0
X
X
X
VCOSBR[4] VCOSBR[3] VCOSBR[2] VCOSBR[1] VCOSBR[0] ADC[2] ADC[1] ADC[0]
0 = Set to 0 for factory-tested operation.
1 = Set to 1 for factory-tested operation.
Complete Direct-Conversion L-Band Tuner
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
FRAC
7
1
N[14:8]
6–0
0000000
MAX2121
Table 2. N-Divider MSB Register (Address: 0x00)
FUNCTION
Users must program to 1 upon powering up the device.
Sets the most significant bits of the PLL integer-divide number (N). N can
range from 19 to 251.
Table 3. N-Divider LSB Register (Address: 0x01)
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
FUNCTION
N[7:0]
7–0
00100011
Sets the least significant bits of the PLL integer-divide number. N can range
from 19 to 251.
Table 4. Charge-Pump Register (Address: 0x02)
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
FUNCTION
CPMP[1:0]
7–6
00
Charge-pump minimum pulse width. Users must program to 00 upon
powering up the device.
CPLIN[1:0]
5–4
00
Controls charge-pump linearity. Users must program to 01 upon powering
up the device.
F[19:16]
3–0
0010
Sets the 4 most significant bits of the PLL fractional divide number.
Default value is F = 194,180 decimal.
Table 5. F-Divider MSB Register (Address: 0x03)
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
F[15:8]
7–0
11110110
FUNCTION
Sets the most significant bits of the PLL fractional-divide number (F).
Default value is F = 194,180 decimal.
Table 6. F-Divider LSB Register (Address: 0x04)
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
F[7:0]
7–0
10000100
FUNCTION
Sets the least significant bits of the PLL fractional-divide number (F).
Default value is F = 194,180 decimal.
Table 7. XTAL Buffer and Reference Divider Register (Address: 0x05)
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
XD[2:0]
7–5
000
R[4:0]
4–0
00001
FUNCTION
Sets the crystal-divider setting.
000 = Divide by 1.
001 = Divide by 2.
011 = Divide by 3.
100 = Divide by 4.
101 through 110 = All divide values from 5 (101) to 7 (110).
111 = Divide by 8.
Sets the PLL reference-divider (R) number. Users must program to 00001
upon powering up the device.
00001 = Divide by 1; other values are not tested.
11
MAX2121
Complete Direct-Conversion L-Band Tuner
Table 8. PLL Register (Address: 0x06)
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
FUNCTION
D24
7
1
VCO divider setting.
0 = Divide by 2. Use for LO frequencies 1125MHz.
1 = Divide by 4. Use for LO frequencies < 1125MHz.
CPS
6
1
Charge-pump current mode.
0 = Charge-pump current controlled by ICP bit.
1 = Charge-pump current controlled by VCO autoselect (VAS).
ICP
5
0
Charge-pump current.
0 = 600µA typical.
1 = 1200µA typical.
X
4–0
X
Don’t care.
Table 9. VCO Register (Address: 0x07)
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
FUNCTION
VCO[4:0]
7–3
11001
Controls which VCO is activated when using manual VCO programming mode.
This also serves as the starting point for the VCO autoselection (VAS) mode.
VAS
2
1
VCO autoselection (VAS) circuit.
0 = Disable VCO selection must be programmed through I2C.
1 = Enable VCO selection controlled by autoselection circuit.
0
Enables or disables the VCO tuning voltage ADC latch when the VCO
autoselect mode (VAS) is disabled.
0 = Disables the ADC latch.
1 = Latches the ADC value.
0
Enables or disables VCO tuning voltage ADC read when the VCO
autoselect mode (VAS) is disabled.
0 = Disables ADC read.
1 = Enables ADC read.
ADL
ADE
1
0
Table 10. Lowpass Filter Register (Address: 0x08)
BIT NAME
BIT LOCATION (0 = LSB)
Reserved
7–0
12
DEFAULT
FUNCTION
01001011 User must program to 10010111 (97h) upon powering up the device.
Complete Direct-Conversion L-Band Tuner
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
FUNCTION
Software standby control.
0 = Normal operation.
1 = Disables the signal path and frequency synthesizer leaving only the
2-wire bus, crystal oscillator, XTALOUT buffer, and XTALOUT buffer divider
active.
STBY
7
0
X
6
X
Don’t care.
PWDN
5
0
Factory use only.
0 = Normal operation; other value is not tested.
X
4
X
Don’t care.
BBG[3:0]
3–0
0000
MAX2121
Table 11. Control Register (Address: 0x09)
Baseband gain setting (1dB typical per step).
0000 = Minimum gain (0dB, default).
…
1111 = Maximum gain (15dB typical).
Table 12. Shutdown Register (Address: 0x0A)
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
X
7
X
Don’t care.
FUNCTION
PLL
6
0
PLL enable.
0 = Normal operation.
1 = Shuts down the PLL. Value not tested.
DIV
5
0
Divider enable.
0 = Normal operation.
1 = Shuts down the divider. Value not tested.
VCO
4
0
VCO enable.
0 = Normal operation.
1 = Shuts down the VCO. Value not tested.
BB
3
0
Baseband enable.
0 = Normal operation.
1 = Shuts down the baseband. Value not tested.
RFMIX
2
0
RF mixer enable.
0 = Normal operation.
1 = Shuts down the RF mixer. Value not tested.
RFVGA
1
0
RF VGA enable.
0 = Normal operation.
1 = Shuts down the RF VGA. Value not tested.
FE
0
0
Front-end enable.
0 = Normal operation.
1 = Shuts down the front-end. Value not tested.
13
MAX2121
Complete Direct-Conversion L-Band Tuner
Table 13. Test Register (Address: 0x0B)
BIT NAME
BIT LOCATION (0 = LSB)
DEFAULT
CPTST[2:0]
7–5
000
X
4
X
Don’t care.
Charge-pump fast lock.
Users must program to 1 after powering up the device.
TURBO
3
1
LDMUX[2:0]
2–0
000
FUNCTION
Charge-pump test modes.
000 = Normal operation (default).
REFOUT output.
000 = Normal operation; other values are not tested.
Table 14. Status Byte-1 Register (Address: 0x0C)
BIT NAME
BIT LOCATION (0 = LSB)
FUNCTION
POR
7
Power-on reset status.
0 = Chip status register has been read with a stop condition since last power-on.
1 = Power-on reset (power cycle) has occurred. Default values have been loaded in
registers.
VASA
6
Indicates whether VCO autoselection was successful.
0 = Indicates the autoselect function is disabled or unsuccessful VCO selection.
1 = Indicates successful VCO autoselection.
VASE
5
Status indicator for the autoselect function.
0 = Indicates the autoselect function is active.
1 = Indicates the autoselect process is inactive.
LD
4
PLL lock detector. TURBO bit must be programmed to 1 for valid LD reading.
0 = Unlocked.
1 = Locked.
X
3–0
Don’t care.
Table 15. Status Byte-2 Register (Address: 0x0D)
BIT NAME
BIT LOCATION (0 = LSB)
VCOSBR[4:0]
7–3
VCO band readback.
2–0
VAS ADC output readback.
000 = Out of lock.
001 = Locked.
010 = VAS locked.
101 = VAS locked.
110 = Locked.
111 = Out of lock.
ADC[2:0]
14
FUNCTION
Complete Direct-Conversion L-Band Tuner
START and STOP Conditions
The master initiates a transmission with a START condition (S), which is a high-to-low transition on SDA while
SCL is high. The master terminates a transmission with
a STOP condition (P), which is a low-to-high transition
on SDA while SCL is high.
Acknowledge and Not-Acknowledge Conditions
Data transfers are framed with an acknowledge bit
(ACK) or a not-acknowledge bit (NACK). Both the master and the MAX2121 (slave) generate acknowledge
bits. To generate an acknowledge, the receiving device
must pull SDA low before the rising edge of the
acknowledge-related clock pulse (ninth pulse) and
keep it low during the high period of the clock pulse.
To generate a not-acknowledge condition, the receiver
allows SDA to be pulled high before the rising edge of
the acknowledge-related clock pulse, and leaves SDA
high during the high period of the clock pulse.
Monitoring the acknowledge bits allows for detection of
unsuccessful data transfers. An unsuccessful data
transfer happens if a receiving device is busy or if a
system fault has occurred. In the event of an unsuccessful data transfer, the bus master must reattempt
communication at a later time.
START
Slave Address
The MAX2121 has a 7-bit slave address that must be
sent to the device following a START condition to initiate communication. The slave address is internally programmed to 1100000. The eighth bit (R/W) following
the 7-bit address determines whether a read or write
operation occurs.
The MAX2121 continuously awaits a START condition
followed by its slave address. When the device recognizes its slave address, it acknowledges by pulling the
SDA line low for one clock period; it is ready to accept
or send data depending on the R/W bit (Figure 1).
The write/read address is C0/C1 if ADDR pin is connected to ground. The write/read address is C2/C3 if
the ADDR pin is connected to VCC.
SLAVE ADDRESS
1
S
1
0
0
0
0
0
SDA
SCL
1
2
3
4
5
6
R/W
ACK
8
9
7
Figure 1. MAX2121 Slave Address Byte with ADDR Pin
Connected to Ground
Write Cycle
When addressed with a write command, the MAX2121
allows the master to write to a single register or to multiple successive registers.
A write cycle begins with the bus master issuing a
START condition followed by the seven slave address
bits and a write bit (R/W = 0). The MAX2121 issues an
ACK if the slave address byte is successfully received.
The bus master must then send to the slave the address
of the first register it wishes to write to (see Table 1 for
register addresses). If the slave acknowledges the
address, the master can then write one byte to the register at the specified address. Data is written beginning
with the most significant bit. The MAX2121 again issues
an ACK if the data is successfully written to the register.
The master can continue to write data to the successive
internal registers with the MAX2121 acknowledging each
successful transfer, or it can terminate transmission by
issuing a STOP condition. The write cycle does not terminate until the master issues a STOP condition.
WRITE DEVICE
ADDRESS
R/W
ACK
WRITE REGISTER
ADDRESS
ACK
WRITE DATA TO
REGISTER 0x00
ACK
WRITE DATA TO
REGISTER 0x01
ACK
WRITE DATA TO
REGISTER 0x02
ACK
1100000
0
—
0x00
—
0x0E
—
0xD8
—
0xE1
—
STOP
Figure 2. Example: Write Registers 0, 1, and 2 with 0x0E, 0xD8, and 0xE1, respectively.
15
MAX2121
2-Wire Serial Interface
The MAX2121 uses a 2-wire I2C-compatible serial interface consisting of a serial-data line (SDA) and a serialclock line (SCL). SDA and SCL facilitate bidirectional
communication between the MAX2121 and the master
at clock frequencies up to 400kHz. The master initiates
a data transfer on the bus and generates the SCL signal to permit data transfer. The MAX2121 behaves as a
slave device that transfers and receives data to and
from the master. SDA and SCL must be pulled high
with external pullup resistors (1kΩ or greater) for proper
bus operation. Pullup resistors should be referenced to
the MAX2121’s VCC.
One bit is transferred during each SCL clock cycle. A
minimum of nine clock cycles is required to transfer a
byte in or out of the MAX2121 (8 bits and an ACK/NACK).
The data on SDA must remain stable during the high
period of the SCL clock pulse. Changes in SDA while
SCL is high and stable are considered control signals
(see the START and STOP Conditions section). Both SDA
and SCL remain high when the bus is not busy.
MAX2121
Complete Direct-Conversion L-Band Tuner
START
WRITE DEVICE ADDRESS
R/W
ACK
READ FROM STATUS BYTE-1 REGISTER
ACK
READ FROM STATUS BYTE-2 REGISTER
ACK/
NACK
1100000
1
—
—
—
—
—
STOP
Figure 3. Example: Receive Data from Read Registers
Read Cycle
When addressed with a read command, the MAX2121
allows the master to read back a single register, or multiple successive registers.
A read cycle begins with the bus master issuing a
START condition followed by the seven slave address
bits and a write bit (R/W = 0). The MAX2121 issues an
ACK if the slave address byte is successfully received.
The bus master must then send the address of the first
register it wishes to read (see Table 1 for register
addresses). The slave acknowledges the address.
Then, a START condition is issued by the master, followed by the seven slave address bits and a read bit
(R/W = 1). The MAX2121 issues an ACK if the slave
address byte is successfully received. The MAX2121
starts sending data MSB first with each SCL clock
cycle. At the 9th clock cycle, the master can issue an
ACK and continue to read successive registers, or the
master can terminate the transmission by issuing a
NACK. The read cycle does not terminate until the master issues a STOP condition.
Figure 3 illustrates an example in which registers 0, 1,
and 2 are read back.
Application Information
The MAX2121 downconverts RF signals in the 925MHz
to 2175MHz range directly to the baseband I/Q signals.
RF Input
The RF input of the MAX2121 is internally matched to
75Ω. Only a DC-blocking capacitor is needed. See the
Typical Application Circuit.
RF Gain Control
The MAX2121 features a variable-gain low-noise amplifier providing 73dB of RF gain range. The voltage control (VGC) range is 0.5V (minimum attenuation) to 2.7V
(maximum attenuation).
Baseband Variable-Gain Amplifier
The receiver baseband variable-gain amplifiers provide
15dB of gain control range programmable in 1dB
steps. The VGA gain can be serially programmed
through the I2C interface by setting bits BBG[3:0] in the
Control register.
16
Table 16. Maximum Crystal ESR
Requirement
ESRMAX ()
XTAL FREQUENCY (MHz)
80
12 < f XTAL 14
14 < f XTAL 30
60
Baseband Lowpass Filter
The MAX2121 includes an on-chip 5th-order Butterworth
filter with 1st-order group delay compensation.
DC Offset Cancellation
The DC offset cancellation is required to maintain the
I/Q output dynamic range. Connecting an external
capacitor between IDC+ and IDC- forms a highpass filter for the I channel and an external capacitor between
QDC+ and QDC- forms a highpass filter for the Q channel. Keep the value of the external capacitor less than
47nF to form a typical highpass corner of 250Hz.
XTAL Oscillator
The MAX2121 contains an internal reference oscillator,
reference output divider, and output buffer. All that is
required is to connect a crystal through a series 1nF
capacitor. To minimize parasitics, place the crystal and
series capacitor as close as possible to pin 14 (XTAL).
See Table 16 for crystal (XTAL) ESR (equivalent series
resistance) requirements.
Programming the Fractional
N- Synthesizer
The MAX2121 utilizes a fractional-N type synthesizer for
LO frequency programming. To program the frequency
synthesizer, the N and F values are encoded as
straight binary numbers. Determination of these values
is illustrated by the following example:
fLO is 2170MHz
fXTAL is 27 MHz
Phase-detector comparison frequency is from 12MHz
and 30MHz
R divider = R[4:0] = 1
fCOMP = 27MHz/1 = 27MHz
D = fLO/fCOMP = 2170/27 = 80.37470
Complete Direct-Conversion L-Band Tuner
Table 17. ADC Trip Points and Lock Status
N[7:0] = 0101 0000
Fractional portion:
F = 0.370370 x 220 = 388,361 (round up the decimal portion)
F = 0101 1110 1101 0000 1001
Note: When changing LO frequencies, all the divider
registers (integer and fractional) must be programmed
to activate the VAS function regardless of whether individual registers are changed.
VCO Autoselect (VAS)
The MAX2121 includes 24 VCOs. The local oscillator
frequency can be manually selected by programming
the VCO[4:0] bits in the VCO register. The selected VCO
is reported in the Status Byte-2 register (see Table 15).
Alternatively, the MAX2121 can be set to autonomously
choose a VCO by setting the VAS bit in the VCO register to logic-high. The VAS routine is initiated once the
F-Divider LSB register word (register 5) is loaded.
Thus it is important to write register 5 after any of the
following PLL related bits have been changed:
N-Divider bits (registers 1 and/or 2)
F-Divider bits (registers 3 and/or 4)
Reference Divider bits (register 6)
D24, CPS, or ICP bits (register 7)
This will ensure all intended bits have been programmed before the VAS is initiated and the PLL is
locked. The VCO value programmed in the VCO[4:0]
register serves as the starting point for the automatic
VCO selection process.
During the selection process, the VASE bit in the Status
Byte-1 register is cleared to indicate the autoselection
function is active. Upon successful completion, bits VASE
and VASA are set and the VCO selected is reported in the
Status Byte-2 register (see Table 15). If the search is
unsuccessful, VASA is cleared and VASE is set. This indicates that searching has ended but no good VCO has
been found, and occurs when trying to tune to a frequency outside the VCO’s specified frequency range.
Refer to Application Note 4256: Extended Characterization
for the MAX2112/MAX2120 Satellite Tuners.
ADC[2:0]
LOCK STATUS
000
Out of lock
001
Locked
010
VAS locked
101
VAS locked
110
Locked
111
Out of lock
Table 17 summarizes the ADC output bits and the VCO
lock indication. The VCO autoselect routine only selects
a VCO in the “VAS locked” range. This allows room for
a VCO to drift over temperature and remain in a valid
“locked” range.
The ADC must first be enabled by setting the ADE bit in
the VCO register. The ADC reading is latched by a subsequent programming of the ADC latch bit (ADL = 1).
The ADC value is reported in the Status Byte-2 register
(see Table 15).
Standby Mode
The MAX2121 features normal operating mode and
standby mode using the I2C interface. Setting a logichigh to the STBY bit in the Control register puts the
device into standby mode, during which only the 2wire-compatible bus, the crystal oscillator, the XTAL
buffer, and the XTAL buffer divider are active.
In all cases, register settings loaded prior to entering
shutdown are saved upon transition back to active
mode. Default register values are provided for the
user’s convenience only. It is the user’s responsibility to
load all the registers no sooner than 100µs after the
device is powered up.
Layout Considerations
The MAX2121 EV kit serves as a guide for PCB layout.
Keep RF signal lines as short as possible to minimize
losses and radiation. Use controlled impedance on all
high-frequency traces. For proper operation, the
exposed paddle must be soldered evenly to the board’s
ground plane. Use abundant vias beneath the exposed
paddle for maximum heat dissipation. Use abundant
ground vias between RF traces to minimize undesired
coupling. Bypass each VCC pin to ground with a 1nF
capacitor placed as close as possible to the pin.
3-Bit ADC
The MAX2121 has an internal 3-bit ADC connected to
the VCO tune pin (TUNEVCO). This ADC can be used
for checking the lock status of the VCOs.
17
MAX2121
Integer portion:
N = 80
N[14:8] = 0
Complete Direct-Conversion L-Band Tuner
MAX2121
Typical Application Circuit
SERIAL-DATA
INPUT/OUTPUT
VCC
VCC_RF2
+
28
27
26
25
24
23
1
VCC
22
IDC+
21
DC OFFSET
CORRECTION
INTERFACE LOGIC
AND CONTROL
VCC_RF1
IDC-
QDC+
QDC-
VCC_BB
VCC
SDA
SCL
ADDR
SERIAL-CLOCK
INPUT
IOUT-
MAX2121
2
20
3
19
4
18
5
17
IOUT+
GND
QOUT-
RF INPUT
RFIN
VGC
GC1
QOUT+
VCC
FREQUENCY
SYNTHESIZER
DIV2
/DIV4
VCC_LO
6
VCC
BASEBAND
OUTPUTS
16
VCC
VCC_DIG
EP
REFOUT
VCC_VCO
15
7
13
VCC_SYN
14
XTAL
12
CPOUT
11
GNDSYN
10
GNDTUNE
9
TUNEVCO
BYPVCO
8
VCC
Chip Information
PROCESS: BiCMOS
18
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
28 TQFN-EP
T2855+3
21-0140
90-0023
Complete Direct-Conversion L-Band Tuner
REVISION
NUMBER
REVISION
DATE
0
6/11
Initial release
1
7/12
Corrected 2-tone frequencies, added new TOCs, added text to Register Description
section, corrected incorrect symbol in Table 8, corrected VCO Autoselect (VAS)
section
DESCRIPTION
PAGES
CHANGED
—
4, 6, 10, 17
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in
the Electrical. Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated Products, 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 ____________________ 19
© 2012 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
MAX2121
Revision History