LTM4606 Ultralow EMI 28VIN, 6A DC/DC µModule Regulator Features Description Complete Low EMI Switch Mode Power Supply Wide Input Voltage Range: 4.5V to 28V 6A DC Typical, 8A Peak Output Current 0.6V to 5V Output Voltage Range EN55022 Class B Certified Output Voltage Tracking and Margining PLL Frequency Synchronization ±1.75% Total DC Error Power Good Output Current Foldback Protection (Disabled at Start-Up) Parallel/Current Sharing Ultrafast Transient Response Current Mode Control Up to 93% Efficiency at 5VIN , 3.3VOUT Programmable Soft-Start Output Overvoltage Protection –55°C to 125°C Operating Temperature Range (LTM4606MPV) n Small Surface Mount Footprint, Low Profile Package (15mm × 15mm × 2.8mm) The LTM®4606 is a complete EN55022 Class B certified noise high voltage 6A switching mode DC/DC power supply. Included in the package are the switching controller, power FETs, inductor, and all support components. The on-board input filter and noise cancellation circuits achieve low noise operation, thus effectively reducing the electromagnetic interference (EMI). Operating over an input voltage range of 4.5V to 28V, the LTM4606 supports an output voltage range of 0.6V to 5V, set by a single resistor. This high efficiency design delivers 6A continuous current (8A peak). Only bulk input and output capacitors are needed to finish the design. n n n n n n n n n n n n n n n n n Applications n n n ASICs or FPGA Transceivers Telecom, Servers and Networking Equipment Industrial Equipment RF Equipment L, LT, LTC, LTM, Linear Technology, the Linear logo, µModule and PolyPhase are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Furthermore, the µModule® regulator can be synchronized with an external clock for reducing undesirable frequency harmonics and allows PolyPhase® operation for high load currents. The LTM4606 is offered in a space saving and thermally enhanced 15mm × 15mm × 2.8mm LGA package, which enables utilization of unused space on the bottom of PC boards for high density point of load regulation. The LTM4606 is Pb-free and RoHS compliant. Typical Application Radiated Emission Scan at 12VIN, 2.5VOUT/6A 50 Ultralow Noise 2.5V/6A Power Supply with 4.5V to 28V Input 4.5V TO 28V ON/OFF CIN 10µF 35V CERAMIC x2 40 CLOCK SYNC TRACK/SS CONTROL 10µF 35V VIN PLLIN VOUT PGOOD RUN LTM4606 COMP INTVCC DRVCC fSET TRACK/SS VD SGND 2.5V AT 6A 47pF VFB FCB MARG0 MARG1 MPGM PGND RFB 19.1k MARGIN CONTROL 392k 5% MARGIN 4606 TA01a COUT SIGNAL AMPLITUDE (dBµV/m) n High switching frequency and an adaptive on-time current mode architecture enables a very fast transient response to line and load changes without sacrificing stability. The device supports output voltage tracking and output voltage margining. 30 20 10 0 –10 –20 –30 30 226.2 422.4 618.6 814.8 1010 128.1 324.3 520.5 716.7 912.9 FREQUENCY (MHz) 4606 TA01b 4606fb 1 LTM4606 Absolute Maximum Ratings Pin Configuration (Note 1) TOP VIEW fSET MARG0 MARG1 DRVCC VFB PGOOD SGND NC NC NC FCB DRVCC, VOUT................................................. –0.3V to 6V PLLIN, FCB, TRACK/SS, MPGM, MARG0, MARG1, PGOOD, RUN ...............–0.3V to INTVCC + 0.3V VFB, COMP................................................. –0.3V to 2.7V VIN, VD........................................................ –0.3V to 28V Internal Operating Temperature Range (Note 2) E and I Grades.................................... –40°C to 125°C MP Grade............................................ –55°C to 125°C Junction Temperature............................................ 125°C Storage Temperature Range................... –45°C to 125°C MPGM COMP RUN TRACK/SS PLLIN INTVCC 12 11 10 SGND 9 VD 8 7 6 5 4 3 2 1 A B C D VIN BANK 1 E F G PGND BANK 2 H J K L M VOUT BANK 3 LGA PACKAGE 133-LEAD (15mm × 15mm × 2.8mm) TJMAX = 125°C, θJA = 15°C/W, θJCbottom = 6°C/W, θJCtop = 16°C/W θJA DERIVED FROM 95mm × 76mm PCB WITH 4 LAYERS WEIGHT = 1.7g order information LEAD FREE FINISH TRAY PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTM4606EV#PBF LTM4606EV#PBF LTM4606V 133-Lead (15mm × 15mm × 2.8mm) LGA –40°C to 125°C LTM4606IV#PBF LTM4606IV#PBF LTM4606V 133-Lead (15mm × 15mm × 2.8mm) LGA –40°C to 125°C LTM4606MPV#PBF LTM4606MPV#PBF LTM4606MPV 133-Lead (15mm × 15mm × 2.8mm) LGA –55°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/ Electrical Characteristics The l denotes the specifications which apply over the specified internal operating temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 12V, unless otherwise noted. Per typical application (front page) configuration, RFB = 40.2k. SYMBOL PARAMETER CONDITIONS VIN(DC) Input DC Voltage VOUT(DC) Output Voltage, Total Variation with Line and Load CIN = 10µF x2, COUT = 200µF; FCB = 0 VIN = 5V to 28V, IOUT = 0A to 6A, (Note 4) VIN(UVLO) Undervoltage Lockout Threshold IINRUSH(VIN) Input Inrush Current at Start-Up MIN l 4.5 l 1.474 TYP MAX UNITS 28 V 1.5 1.526 V IOUT = 0A 3.2 4 V IOUT = 0A, CIN = 10µF x2, COUT = 200µF, VOUT = 1.5V VIN = 5V VIN = 12V 0.6 0.7 Input Specifications A A 4606fb 2 LTM4606 Electrical Characteristics The l denotes the specifications which apply over the specified internal operating temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 12V, unless otherwise noted. Per typical application (front page) configuration, RFB = 40.2k. SYMBOL PARAMETER CONDITIONS IQ(VIN) Input Supply Bias Current VIN = 5V, VOUT = 1.5V, Switching Continuous VIN = 12V, VOUT = 1.5V, Switching Continuous Shutdown, RUN = 0, VIN = 12V IS(VIN) Input Supply Current INTVCC VIN = 12V, RUN > 2V MIN TYP MAX 27 25 22 VIN = 12V, VOUT = 1.5V, IOUT = 6A VIN = 5V, VOUT = 1.5V, IOUT = 6A mA mA µA 0.96 2.18 No Load 4.7 5 UNITS A A 5.3 V 6 A 0.3 % 0.3 % Output Specifications IOUT(DC) Output Continuous Current Range VIN = 12V, VOUT = 1.5V (Note 4) DVOUT(LINE)/VOUT Line Regulation Accuracy VOUT = 1.5V, FCB = 0V, VIN = 4.5V to 28V, IOUT = 0A DVOUT(LOAD)/VOUT Load Regulation Accuracy VOUT = 1.5V, FCB = 0V, IOUT = 0A to 6A VIN = 12V (Note 4) VIN(AC) VOUT(AC) Input Ripple Voltage Output Ripple Voltage 0 0.05 l l IOUT = 0A, CIN = 10µF X5R Ceramic x3 and 100µF Electrolytic VIN = 5V, VOUT = 1.5V VIN = 12V, VOUT = 1.5V 2 3 mVP-P mVP-P IOUT = 0A, COUT = 22µF X5R Ceramic x3 and 100µF X5R Ceramic VIN = 5V, VOUT = 1.5V VIN = 12V, VOUT = 1.5V 8 11 mVP-P mVP-P fS Output Ripple Voltage Frequency IOUT = 5A, VIN = 12V, VOUT = 1.5V 900 kHz DVOUT(START) Turn-On Overshoot, TRACK/SS = 10nF COUT = 200µF, VOUT = 1.5V, IOUT = 0A VIN = 12V VIN = 5V 20 20 mV mV tSTART Turn-On Time, TRACK/SS = Open COUT = 200µF; VOUT = 1.5V, IOUT = 1A Resistive Load VIN = 5V VIN = 12V 0.5 0.5 ms ms 35 mV 25 µs 10 10 A A DVOUT(LS) Peak Deviation for Dynamic Load Load: 0% to 50% to 0% of Full Load COUT = 22µF Ceramic, 470µF x2 VIN = 12V VOUT = 1.5V tSETTLE Settling Time for Dynamic Load Step Load: 0% to 50% to 0% of Full Load, VIN = 12V VIN = 12V IOUT(PK) Output Current Limit COUT = 200µF VIN = 5V, VOUT = 1.5V VIN = 12V, VOUT = 1.5V VFB Voltage at VFB Pin IOUT = 0A, VOUT = 1.5V VRUN RUN Pin On/Off Threshold ISS / TRACK Soft-Start Charging Current VFCB Forced Continuous Threshold IFCB Forced Continuous Pin Current VFCB = 0V Control Section VSS/TRACK = 0V l 0.591 0.6 0.609 V 1 1.5 1.9 V –1 –1.5 –2 µA 0.57 0.6 0.63 V –1 –2 µA tON(MIN) Minimum On Time (Note 3) 50 100 ns tOFF(MIN) Minimum Off Time (Note 3) 250 400 ns RPLLIN PLLIN Input Resistor 50 kW 4606fb 3 LTM4606 Electrical Characteristics The l denotes the specifications which apply over the specified internal operating temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN = 12V, unless otherwise noted. Per typical application (front page) configuration, RFB = 40.2k. SYMBOL PARAMETER CONDITIONS IDRVCC Current into DRVCC Pin VOUT = 1.5V, IOUT = 1A RFBHI Resistor Between VOUT and VFB Pins RUNMAX Volts From RUN to GND Maximum MIN TYP 15 25 mA 60.098 60.4 60.702 kW 5.1V Zener Clamp MAX UNITS 5 V Margin Section MPGM Margin Reference Voltage Sets a Current 1.18 V MARG0, MARG1 Voltage Thresholds 1.4 V PGOOD DVFBH PGOOD Upper Threshold VFB Rising 7 10 13 % DVFBL PGOOD Lower Threshold VFB Falling –7 –10 –13 % DVFB(HYS) PGOOD Hysteresis VFB Returning 1.5 VPGL PGOOD Low Voltage IPGOOD = 5mA 0.15 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTM4606E is guaranteed to meet performance specifications over the 0°C to 125°C internal operating temperature range. Specifications over the –40°C to 125°C internal operating temperature range are assured by design, characterization and correlation with statistical process controls. The LTM4606I is guaranteed to meet specifications over the % 0.4 V –40°C to 125°C internal operating temperature range. The LTM4606MP is guaranteed and tested over the –55°C to 125°C internal operating temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal resistance and other environmental factors. Note 3: 100% tested at die level only. Note 4: See output current derating curves for different VIN, VOUT and TA. 4606fb 4 LTM4606 Typical Performance Characteristics 100 80 70 0.6VOUT 1.2VOUT 1.8VOUT 2.5VOUT 3.3VOUT 60 50 100 90 EFFICIENCY (%) EFFICIENCY (%) 90 Efficiency vs Load Current with 12VIN (FCB = 0) 0 1 2 3 4 LOAD CURRENT (A) 5 80 70 1.2VOUT 1.5VOUT 2.5VOUT 3.3VOUT 5VOUT 60 6 50 0 1 2 3 4 LOAD CURRENT (A) 4606 G01 5 80 70 60 6 50 1.5V Transient Response 1 2 3 4 LOAD CURRENT (A) IOUT 2A/DIV VOUT 50mV/DIV VOUT 50mV/DIV VOUT 50mV/DIV 4606 G04 50µs/DIV 1.5V AT 3.5A/µs LOAD STEP COUT = 2× 22µF, 10V CERAMIC 1× 100µF, 6.3V CERAMIC 2.5V Transient Response 4606 G05 50µs/DIV 1.8V AT 3.5A/µs LOAD STEP COUT = 2× 22µF, 10V CERAMIC 1× 100µF, 6.3V CERAMIC 3.3V Transient Response IOUT 2A/DIV IOUT 2A/DIV VOUT 50mV/DIV VOUT 100mV/DIV 5 6 1.8V Transient Response IOUT 2A/DIV 4606 G07 0 4606 G03 IOUT 2A/DIV 50µs/DIV 2.5V AT 3.5A/µs LOAD STEP COUT = 2× 22µF, 10V CERAMIC 1× 100µF, 6.3V CERAMIC 2.5VOUT 3.3VOUT 5VOUT 4606 G02 1.2V Transient Response 50µs/DIV 1.2V AT 3.5A/µs LOAD STEP COUT = 2× 22µF, 10V CERAMIC 1× 100µF, 6.3V CERAMIC Efficiency vs Load Current with 24VIN (FCB = 0) 90 EFFICIENCY (%) 100 Efficiency vs Load Current with 5VIN (FCB = 0) 4606 G06 –55°C, Start-Up, IOUT = 0A VOUT 0.5V/DIV IIN 0.5A/DIV 50µs/DIV 3.3V AT 3.5A/µs LOAD STEP COUT = 2× 22µF, 10V CERAMIC 1× 100µF, 6.3V CERAMIC 4606 G08 1ms/DIV VIN = 12V VOUT = 1.5V COUT = 2× 22µF, 10V CERAMIC 1× 100µF, 6.3V CERAMIC SOFT-START = 3.9nF 4606 G09 4606fb 5 LTM4606 Typical Performance Characteristics –55°C, Start-Up, IOUT = 6A Start-Up, IOUT = 6A (Resistive Load) Start-Up, IOUT = 0A VOUT 0.5V/DIV VOUT 0.5V/DIV VOUT 0.5V/DIV IIN 0.5A/DIV 4606 G10 1ms/DIV VIN = 12V VOUT = 1.5V COUT = 2× 22µF, 10V CERAMIC 1× 100µF, 6.3V CERAMIC SOFT-START = 3.9nF IIN 0.5A/DIV IIN 0.5A/DIV 1ms/DIV VIN = 12V VOUT = 1.5V COUT = 1× 22µF, 6.3V CERAMIC 1× 330µF, 4V SANYO POSCAP SOFT-START = 3.9nF 4606 G11 1ms/DIV VIN = 12V VOUT = 1.5V COUT = 1× 22µF, 6.3V CERAMIC 1× 330µF, 4V SANYO POSCAP SOFT-START = 3.9nF Short-Circuit Protection, IOUT = 6A VOUT 2V/DIV VOUT 1V/DIV IIN 0.2A/DIV IIN 2A/DIV 4606 G13 50µs/DIV VIN = 12V VOUT = 2.5V COUT = 2× 22µF, 10V CERAMIC 1× 100µF, 6.3V CERAMIC SOFT-START = 0.1µF VIN to VOUT Step-Down Operation Region 28 24 SEE FREQUENCY ADJUSTMENT SECTION FOR OPERATIONS OUTSIDE THIS REGION 20 VIN (V) Short-Circuit Protection, IOUT = 0A 4606 G12 50µs/DIV VIN = 12V VOUT = 2.5V COUT = 2× 22µF, 10V CERAMIC 1× 100µF, 6.3V CERAMIC SOFT-START = 0.1µF 4606 G14 16 OPERATION REGION WITH DEFAULT FREQUENCY 12 8 4.5 0.6 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VOUT (V) 4606 G15 Input Ripple VFB vs Temperature Output Ripple 0.606 0.604 VFB (V) VOUT 2mV/DIV VIN 10mV/DIV 0.602 0.600 0.598 2µs/DIV VIN = 5V VOUT = 1V AT 6A CIN = 3× 10µF, 25V CERAMIC 1× 150µF BULK BW = 300MHz 0.596 0.594 –55 –25 35 65 5 TEMPERATURE (°C) 95 4606 G17 2µs/DIV VIN = 5V VOUT = 1V AT 6A COUT = 2× 22µF, 6.3V CERAMIC 1× 100µF, 6.3V CERAMIC BW = 300MHz 4606 G18 125 4606 G16 4606fb 6 LTM4606 Pin Functions VIN (Bank 1): Power Input Pins. Apply input voltage between these pins and PGND pins. Recommend placing input decoupling capacitance directly between VIN pins and PGND pins. VOUT (Bank 3): Power Output Pins. Apply output load between these pins and PGND pins. Recommend placing output decoupling capacitance directly between these pins and PGND pins (see figure below). PGND (Bank 2): Power Ground Pins for Both Input and Output Returns. VD (Pins B7, C7): Top FET Drain Pins. Add more capacitors between VD and ground to handle the input RMS current and reduce the input ripple further. DRVCC (Pins C10, E11, E12): These pins normally connect to INTVCC for powering the internal MOSFET drivers. They can be biased up to 6V from an external supply with about 50mA capability, or an external circuit as shown in Figure 18. This improves efficiency at the higher input voltages by reducing power dissipation in the modules. INTVCC (Pin A7): This pin is for additional decoupling of the 5V internal regulator. PLLIN (Pin A8): External Clock Synchronization Input to the Phase Detector. This pin is internally terminated to SGND with a 50k resistor. Apply a clock with high level above 2V and below INTVCC. See the Applications Information section. FCB (Pin M12): Forced Continuous Input. Connect this pin to SGND to force continuous synchronization operation at low load, to INTVCC to enable discontinuous mode operation at low load or to a resistive divider from a secondary output when using a secondary winding. TRACK/SS (Pin A9): Output Voltage Tracking and Soft-Start Pin. When the module is configured as a master output, then a soft-start capacitor is placed on this pin to ground to control the master ramp rate. A soft-start capacitor can be used for soft-start turn-on as a standalone regulator. Slave operation is performed by putting a resistor divider from the master output to ground, and connecting the center point of the divider to this pin. See the Applications Information section. MPGM (Pins A12, B11): Programmable Margining Input. A resistor from these pins to ground sets a current that is equal to 1.18V/R. This current multiplied by 10kW will equal a value in millivolts that is a percentage of the 0.6V reference voltage. See the Applications Information section. To parallel LTM4606s, each requires an individual MPGM resistor. Do not tie MPGM pins together. fSET (Pin B12): Frequency set internally to 800kHz in continuous conducting mode at light load. An external resistor can be placed from this pin to ground to increase frequency. This pin can be decoupled with a 1000pF capacitor. See the Applications Information section for frequency adjustment. VFB (Pin F12): The Negative Input of the Error Amplifier. Internally, this pin is connected to VOUT with a 60.4k precision resistor. Different output voltages can be programmed with an additional resistor between the VFB and SGND pins. See the Applications Information section. MARG0 (Pin C12): LSB Logic Input for the Margining Function. Together with the MARG1 pin, the MARG0 pin will determine if a margin high, margin low, or no margin state is applied. The pin has an internal pulldown resistor of 50k. See the Applications Information section. MARG1 (Pins C11, D12): MSB Logic Input for the Margining Function. Together with the MARG0 pin, the MARG1 pins will determine if a margin high, margin low, or no margin state is applied. The pins have an internal pull-down resistor of 50k. See the Applications Information section. SGND (Pins D9, H12): Signal Ground Pins. These pins connect to PGND at output capacitor point. COMP (Pins A11, D11): Current Control Threshold and Error Amplifier Compensation Point. The current comparator threshold increases with this control voltage. The voltage ranges from 0V to 2.4V with 0.7V corresponding to zero sense voltage (zero current). PGOOD (Pin G12): Output Voltage Power Good Indicator. Open-drain logic output that is pulled to ground when the output voltage is not within ±10% of the regulation point, after a 25µs power bad mask timer expires. 4606fb 7 LTM4606 Pin Functions NC (Pins J12, K12, L12): These pads must be left floating (electrical open circuit) and are used for increased solder integrity strength. fSET MARG0 MARG1 DRVCC VFB PGOOD SGND NC NC NC FCB RUN (Pins A10, B9): Run Control Pins. A voltage above 1.9V will turn on the module, and below 1V will turn off the module. A programmable UVLO function can be accomplished with a resistor from VIN to this pin that has a 5.1V Zener to ground. Maximum pin voltage is 5V. MPGM COMP RUN TRACK/SS PLLIN INTVCC 12 11 10 SGND 9 VD 8 7 6 5 4 3 2 1 A B C VIN BANK 1 D E F G PGND BANK 2 H J K L M VOUT BANK 3 4606fb 8 LTM4606 Block Diagram >1.9V = ON <1V = OFF MAX = 5V VOUT RUN PGOOD 5.1V ZENER COMP 1.5µF INPUT FILTER + VIN 4.5V TO 28V CIN 60.4k VD INTERNAL COMP CD POWER CONTROL SGND M1 1µH VOUT 2.5V AT 6A MARG1 MARG0 VFB RFB 19.1k 50k 50k fSET M2 NOISE CANCELLATION 22µF 41.2k + COUT PGND FCB 10k MPGM TRACK/SS CSS PLLIN 4.7µF 50k INTVCC DRVCC 4606 F01 Figure 1. Simplified Block Diagram decoupling requirements TA = 25°C. Use Figure 1 configuration. SYMBOL PARAMETER CONDITIONS MIN CIN External Input Capacitor Requirement (VIN = 4.5V to 28V, VOUT = 2.5V) IOUT = 6A 10 COUT External Output Capacitor Requirement (VIN = 4.5V to 28V, VOUT = 2.5V) IOUT = 6A 100 TYP MAX UNITS µF 200 µF 4606fb 9 LTM4606 Operation Power Module Description The LTM4606 is a standalone non-isolated switching mode DC/DC power supply. It can deliver up to 6A of DC output current with some external input and output capacitors. This module provides precisely regulated output voltage programmable via one external resistor from 0.6VDC to 5.0VDC over a 4.5V to 28V input voltage range. The typical application schematic is shown in Figure 20. The LTM4606 has an integrated constant on-time current mode regulator, ultralow RDS(ON) FETs with fast switching speed and integrated Schottky diodes. With current mode control and internal feedback loop compensation, the LTM4606 module has sufficient stability margins and good transient performance under a wide range of operating conditions and with a wide range of output capacitors, even all ceramic output capacitors. Current mode control provides cycle-by-cycle fast current limiting. Besides, foldback current limiting is provided in an overcurrent condition while VFB drops. Internal overvoltage and undervoltage comparators pull the open-drain PGOOD output low if the output feedback voltage exits a ±10% window around the regulation point. Furthermore, in an overvoltage condition, internal top FET M1 is turned off and bottom FET M2 is turned on and held on until the overvoltage condition clears. Input filter and noise cancellation circuits reduce the noise coupling to I/O sides, and ensure the electromagnetic interference (EMI) to meet EN55022 Class B limits. Pulling the RUN pin below 1V forces the controller into its shutdown state, turning off both M1 and M2. At low load currents, discontinuous mode (DCM) operation can be enabled to achieve higher efficiency compared to continuous mode (CCM) by setting the FCB pin higher than 0.6V. When the DRVCC pin is connected to INTVCC an integrated 5V linear regulator powers the internal gate drivers. If a 5V external bias supply is applied on the DRVCC pin, then an efficiency improvement will occur due to the reduced power loss in the internal linear regulator. This is especially true at the higher input voltage range. The MPGM, MARG0 and MARG1 pins are used to support voltage margining, where the percentage of margin is programmed by the MPGM pin, and the MARG0 and MARG1 selected margining. The PLLIN pin provides frequency synchronization of the device to an external clock. The TRACK/SS pin is used for power supply tracking and soft-start programming. 4606fb 10 LTM4606 Applications Information The typical LTM4606 application circuit is shown in Figure 20. External component selection is primarily determined by the maximum load current and output voltage. Refer to Table 2 for specific external capacitor requirements for a particular application. RPGM resistor on the MPGM pin programs the current. Calculate VOUT(MARGIN): VIN to VOUT Step-Down Ratios where %VOUT is the percentage of VOUT you want to margin, and VOUT(MARGIN) is the margin quantity in volts: Under the default frequency, there are restrictions in the maximum VIN and VOUT step-down ratio that can be achieved for a given input voltage. These constraints are caused by the limitation of the minimum on and off time in the internal switches. Refer to the Frequency Adjustment section to change the switching frequency and get wider input and output ranges. See the Thermal Considerations and Output Current Derating section in this data sheet for the current restrictions. VOUT 1.18V • • 10k 0.6V VOUT(MARGIN) The output margining will be ± margining of the value. This is controlled by the MARG0 and MARG1 pins. See the truth table below: MARG1 The PWM controller has an internal 0.6V reference voltage. As shown in the Block Diagram, a 60.4k internal feedback resistor connects the VOUT and VFB pins together. Adding a resistor RFB from the VFB pin to the SGND pin programs the output voltage: RPGM = 60.4k + RFB = 0.6V RFB Table 1. RFB Standard 1% Resistor Values vs VOUT RFB (kΩ) Open 60.4 40.2 30.1 25.5 19.1 13.3 8.25 VOUT (V) 0.6 1.2 1.5 1.8 2 2.5 3.3 5 The MPGM pin programs a current that when multiplied by an internal 10k resistor sets up the 0.6V reference ± offset for margining. A 1.18V reference divided by the %VOUT • VOUT 100 where RPGM is the resistor value to place on the MPGM pin to ground. Output Voltage Programming and Margining VOUT VOUT(MARGIN) = MARG0 MODE LOW LOW NO MARGIN LOW HIGH MARGIN UP HIGH LOW MARGIN DOWN HIGH HIGH NO MARGIN Input Capacitors and Input EMI Noise Attenuation The LTM4606 is designed to achieve low input conducted EMI noise due to the fast switching of turn-on and turn-off. In the LTM4606, a high frequency inductor is integrated to the input line for noise attenuation. VD and VIN pins are available for external input capacitors to form a high frequency π filter. As shown in Figure 19, the ceramic capacitor C1 on the VD pins is used to handle most of the RMS current into the converter, so careful attention is needed for capacitor C1 selection. For a buck converter, the switching duty cycle can be estimated as: D= VOUT VIN 4606fb 11 LTM4606 Applications Information Without considering the inductor ripple current, the RMS current of the input capacitor can be estimated as: ICIN(RMS) = IOUT(MAX) η • D • (1– D) Output Capacitors In the above equation, η is the estimated efficiency of the power module. Note the capacitor ripple current ratings are often based on temperature and hours of life. This makes it advisable to properly derate the capacitor, or choose a capacitor rated at a higher temperature than required. Always contact the capacitor manufacturer for derating requirements. In a typical 6A output application, one or two very low ESR X5R or X7R, 10µF ceramic capacitors are recommended for C1. This decoupling capacitor should be placed directly adjacent to the module VD pins in the PCB layout to minimize the trace inductance and high frequency AC noise. Each 10µF ceramic is typically good for 2 to 3 amps of RMS ripple current. Refer to your ceramics capacitor catalog for the RMS current ratings. To attenuate high frequency noise, extra input capacitors should be connected to the VIN pads and placed before the high frequency inductor to form the π filter. One of these low ESR ceramic capacitors is recommended to be placed close to the connection into the system board. A large bulk 100µF capacitor is only needed if the input source impedance is compromised by long inductive leads or traces. Figure 2 shows the radiated EMI test results to 50 40 SIGNAL AMPLITUDE (dBµV/m) meet EN55022 Class B. For different applications, input capacitance may be varied to meet different radiated EMI limits. 30 20 10 The LTM4606 is designed for low output voltage ripple. The bulk output capacitors defined as COUT are chosen with low enough effective series resistance (ESR) to meet the output voltage ripple and transient requirements. COUT can be a low ESR tantalum capacitor, low ESR polymer capacitor or ceramic capacitor. The typical capacitance is 200µF if all ceramic output capacitors are used. Additional output filtering may be required by the system designer, if further reduction of output ripple or dynamic transient spike is required. Table 2 shows a matrix of different output voltages and output capacitors to minimize the voltage droop and overshoot during a 3A/µs transient. The table optimizes total equivalent ESR and total bulk capacitance to maximize transient performance. Multiphase operation with multiple LTM4606 devices in parallel will lower the effective output ripple current due to the phase interleaving operation. Refer to Figure 3 for the normalized output ripple current versus the duty cycle. Figure 3 provides a ratio of peak-to-peak output ripple current to the inductor ripple current as functions of duty cycle and the number of paralleled phases. Pick the corresponding duty cycle and the number of phases to get the correct output ripple current value. For example, each phase’s inductor ripple current DIr at zero duty cycle is ~2.5A for a 12V to 2.5V design. The duty cycle is about 0.21. The 2-phase curve has a ratio of ~0.58 for a duty cycle of 0.21. This 0.58 ratio of output ripple current to the inductor ripple current DIr at 2.5A equals ~1.5A of the output ripple current (∆IL). The output voltage ripple has two components that are related to the amount of bulk capacitance and effective series resistance (ESR) of the output bulk capacitance. The equation is: 0 –10 –20 –30 30 226.2 422.4 618.6 814.8 1010 128.1 324.3 520.5 716.7 912.9 FREQUENCY (MHz) 4606 F02 Figure 2. Radiated Emission Scan with 12VIN to 2.5VOUT at 6A (1×100µF X7R Ceramic COUT) ⎛ ⎞ DIL DVOUT(P−P) ≈ ⎜ ⎟ + ESR • DIL 8 • f • N • COUT ⎠ ⎝ where f is the frequency and N is the number of paralleled phases. 4606fb 12 LTM4606 Applications Information 1.00 0.95 1-PHASE 2-PHASE 3-PHASE 4-PHASE 6-PHASE 0.90 0.85 RATIO = PEAK-TO-PEAK OUTPUT RIPPLE CURRENT DIr 0.80 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 DUTY CYCLE (VO/VIN) 4612 F05 Figure 3. Normalized Output Ripple Current vs Duty Cycle, Dlr = VOT/LI Fault Conditions: Current Limit and Overcurrent Foldback LTM4606 has a current mode controller, which inherently limits the cycle-by-cycle inductor current not only in steady-state operation, but also in transient. To further limit current in the event of an overload condition, the LTM4606 provides foldback current limiting. If the output voltage falls by more than 50%, then the maximum output current is progressively lowered to about one sixth of its full current limit value. Soft-Start and Tracking The TRACK/SS pin provides a means to either soft-start the regulator or track it to a different power supply. A capacitor on this pin will program the ramp rate of the output voltage. A 1.5µA current source will charge up the external soft-start capacitor to 80% of the 0.6V internal voltage reference plus or minus any margin delta. This will control the ramp of the internal reference and the output voltage. The total soft-start time can be calculated as: ( ) tSOFTSTART ≅ 0.8 • 0.6V ± VOUT(MARGIN) • CSS 1.5µA When the RUN pin falls below 2.5V, then the SS pin is reset to allow for proper soft-start control when the regulator is enabled again. Current foldback and force continuous mode are disabled during the soft-start process. The soft-start function can also be used to control the output ramp up time, so that another regulator can be easily tracked to it. 4606fb 13 LTM4606 Applications Information Output Voltage Tracking Run Enable Output voltage tracking can be programmed externally using the TRACK/SS pin. The output can be tracked up and down with another regulator. Figure 4 shows an example of coincident tracking where the master regulator’s output is divided down with an external resistor divider that is the same as the slave regulator’s feedback divider. Ratiometric modes of tracking can be achieved by selecting different resistor values to change the output tracking ratio. The master output must be greater than the slave output for the tracking to work. Figure 5 shows the coincident output tracking characteristics. The RUN pin is used to enable the power module. The pin has an internal 5.1V zener to ground. The pin can be driven with a logic input not to exceed 5V. VIN VIN PLLIN PGOOD RUN CIN MASTER OUTPUT TRACK CONTROL R2 60.4k R1 19.1k VUVLO = R1+ R2 • 1.5V R2 where R2 is the bottom resistor of the divider, R1 is the top resistor of the divider. Power Good 100k VD The RUN pin can also be used as an undervoltage lock out (UVLO) function by connecting a resistor divider from the input supply to the RUN pin: SLAVE OUTPUT COUT 2.5V VOUT VFB LTM4606 FCB COMP INTVCC MARG0 DRVCC MARG1 fSET COMP Pin MPGM TRACK/SS SGND PGND The PGOOD pin is an open-drain pin that can be used to monitor valid output voltage regulation. This pin monitors a ±10% window around the regulation point and tracks with margining. 19.1k 4606 F04 Figure 4. Output Voltage Coincident Tracking This pin is the external compensation pin. The module has already been internally compensated for most output voltages. Table 2 is provided for most application requirements. LTpowerCAD™ is available for other control loop optimization. FCB Pin MASTER OUTPUT SLAVE OUTPUT OUTPUT VOLTAGE TIME The FCB pin determines whether the bottom MOSFET remains on when current reverses in the inductor. Tying this pin above its 0.6V threshold enables discontinuous operation where the bottom MOSFET turns off when inductor current reverses. FCB pin below the 0.6V threshold forces continuous synchronous operation, allowing current to reverse at light loads and maintain low output ripple. 4606 F05 Figure 5. Coincident Tracking Characteristics 4606fb 14 LTM4606 Applications Information PLLIN Thermal Considerations and Output Current Derating The power module has a phase-locked loop comprised of an internal voltage controlled oscillator and a phase detector. This allows the internal top MOSFET turn-on to be locked to the rising edge of the external clock. The frequency range is ±30% around the operating frequency. A pulse detection circuit is used to detect a clock on the PLLIN pin to turn on the phase lock loop. The pulse width of the clock has to be at least 400ns and 2V in amplitude. During the start-up of the regulator, the phase-lock loop function is disabled. In different applications, LTM4606 operates in a variety of thermal environments. The maximum output current is limited by the environment thermal condition. Sufficient cooling should be provided to help ensure reliable operation. When the cooling is limited, proper output current derating is necessary, considering ambient temperature, airflow, input/output condition, and the need for increased reliability. INTVCC and DRVCC Connection An internal low dropout regulator produces an internal 5V supply that powers the control circuitry and DRVCC for driving the internal power MOSFETs. Therefore, if the system does not have a 5V power rail, the LTM4606 can be directly powered by Vin. The gate driver current through the LDO is about 20mA. The internal LDO power dissipation can be calculated as: PLDO_LOSS = 20mA • (VIN – 5V) The LTM4606 also provides an external gate driver voltage pin DRVCC. If there is a 5V rail in the system, it is recommended to connect DRVCC pin to the external 5V rail. This is especially true for higher input voltages. Do not apply more than 6V to the DRVCC pin. A 5V output can be used to power the DRVCC pin with an external circuit as shown in Figure 18. Parallel Operation of the Module The LTM4606 device is an inherently current mode controlled device. Parallel modules will have very good current sharing. This will balance the thermals on the design. The voltage feedback equation changes with the variable N as modules are paralleled: 60.4k VOUT = 0.6V N + RFB RFB N is the number of paralleled modules. The power loss curves in Figures 6 and 7 can be used in coordination with the load current derating curves in Figures 8 to 15 for calculating an approximate θJA for the module. The graphs delineate between no heat sink, and a BGA heat sink. Each of the load current derating curves will lower the maximum load current as a function of the increased ambient temperature to keep the maximum junction temperature of the power module at 125°C maximum. Each of the derating curves and the power loss curve that corresponds to the correct output voltage can be used to solve for the approximate θJA of the condition. Each figure has three curves that are taken at three different air flow conditions. Tables 3 and 4 provide the approximate θJA for Figures 8 to 15. A complete explanation of the thermal characteristics is provided in the thermal application note AN110. Safety Considerations The LTM4606 modules do not provide isolation from VIN to VOUT. There is no internal fuse. If required, a slow blow fuse with a rating twice the maximum input current needs to be provided to protect each unit from catastrophic failure. Radiated EMI Noise High radiated EMI noise is a disadvantage for switching regulators by nature. Fast switching turn-on and turn-off make large di/dt change in the converters, which act as the radiation sources in most systems. The LTM4606 integrates the feature to minimize the radiated EMI noise for applications with low noise requirements. Optimized gate driver for the MOSFET and noise cancellation network are installed inside the LTM4606 to achieve low radiated EMI noise. Figure 16 shows a typical example for LTM4606 to meet the Class B of EN55022 radiated emission limit. 4606fb 15 LTM4606 Applications Information 4.0 2.5 3.5 24V LOSS 3.0 12V LOSS POWER LOSS (W) POWER LOSS (W) 2.0 1.5 5V LOSS 1.0 2.5 2.0 12V LOSS 1.5 1.0 0.5 0.5 0 0 1 3 5 2 4 OUTPUT CURRENT (A) 6 0 7 0 5 5 MAXIMUM LOAD CURRENT (A) MAXIMUM LOAD CURRENT (A) 6 4 3 2 5VIN, 1.5VOUT, 0LFM 5VIN, 1.5VOUT, 200LFM 5VIN, 1.5VOUT, 400LFM 75 6 80 85 90 AMBIENT TEMPERATURE (°C) 3 2 0 95 5VIN, 1.5VOUT, 0LFM 5VIN, 1.5VOUT, 200LFM 5VIN, 1.5VOUT, 400LFM 1 75 80 85 90 AMBIENT TEMPERATURE (°C) 6 5 5 MAXIMUM LOAD CURRENT (A) MAXIMUM LOAD CURRENT (A) Figure 9. BGA Heat Sink 6 4 3 2 1 75 80 85 90 AMBIENT TEMPERATURE (°C) 12VIN, 1.5VOUT, 0LFM 12VIN, 1.5VOUT, 200LFM 12VIN, 1.5VOUT, 400LFM 95 4606 F09 Figure 8. No Heat Sink 70 4606 F07 4 4606 F08 0 7 Figure 7. 3.3V Power Loss 6 0 3 5 2 4 OUTPUT CURRENT (A) 4606 F06 Figure 6. 1.5V Power Loss 1 1 95 4606 F10 Figure 10. No Heat Sink 4 3 2 12VIN, 1.5VOUT, 0LFM 12VIN, 1.5VOUT, 200LFM 12VIN, 1.5VOUT, 400LFM 1 0 70 95 75 80 85 90 AMBIENT TEMPERATURE (°C) 4606 F11 Figure 11. BGA Heat Sink 4606fb 16 LTM4606 6 6 5 5 MAXIMUM LOAD CURRENT (A) MAXIMUM LOAD CURRENT (A) Applications Information 4 3 2 12VIN, 3.3VOUT, 0LFM 12VIN, 3.3VOUT, 200LFM 12VIN, 3.3VOUT, 400LFM 1 0 70 3 2 12VIN, 3.3VOUT, 0LFM 12VIN, 3.3VOUT, 200LFM 12VIN, 3.3VOUT, 400LFM 1 0 95 75 80 85 90 AMBIENT TEMPERATURE (°C) 4 70 95 75 80 85 90 AMBIENT TEMPERATURE (°C) 4606 F13 4606 F12 Figure 13. BGA Heat Sink 6 5 5 MAXIMUM LOAD CURRENT (A) 6 4 3 2 24VIN, 3.3VOUT, 0LFM 24VIN, 3.3VOUT, 200LFM 24VIN, 3.3VOUT, 400LFM 1 0 60 85 65 70 75 80 AMBIENT TEMPERATURE (°C) 4 3 2 24VIN, 3.3VOUT, 0LFM 24VIN, 3.3VOUT, 200LFM 24VIN, 3.3VOUT, 400LFM 1 0 60 85 65 70 75 80 AMBIENT TEMPERATURE (°C) 90 4606 G15 4606 F14 Figure 14. No Heat Sink Figure 15. BGA Heat Sink 50 40 SIGNAL AMPLITUDE (dBµV/m) MAXIMUM LOAD CURRENT (A) Figure 12. No Heat Sink 30 20 10 0 –10 –20 –30 30 226.2 422.4 618.6 814.8 1010 128.1 324.3 520.5 716.7 912.9 FREQUENCY (MHz) 4606 F16 Figure 16. Radiated Emission Scan with 12VIN to 2.5VOUT at 6A (1×100µF X7R Ceramic COUT) 4606fb 17 LTM4606 Applications Information Table 2. Output Voltage Response vs Component Matrix (Refer to Figure 20) TYPICAL MEASURED VALUES COUT1 VENDORS TAIYO YUDEN TAIYO YUDEN TDK VOUT (V) 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 5 5 5 CIN (CERAMIC) 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V 2 × 10µF 35V PART NUMBER JMK316BJ226ML-T501 (22µF, 6.3V) JMK325BJ476MM-T (47µF, 6.3V) C3225X5R0J476M (47µF, 6.3V) CIN (BULK) 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V 150µF 35V COUT1 (CERAMIC) 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 1 × 22µF 6.3V 1 × 47µF 6.3V 2 × 47µF 6.3V 4 × 47µF 6.3V 4 × 47µF 6.3V 4 × 47µF 6.3V 4 × 47µF 6.3V COUT2 (BULK) 330µF 4V 330µF 2.5V 220µF 6.3V NONE 330µF 4V 330µF 2.5V 220µF 6.3V NONE 330µF 4V 330µF 2.5V 220µF 6.3V NONE 330µF 4V 330µF 2.5V 220µF 6.3V NONE 330µF 4V 330µF 2.5V 220µF 6.3V NONE 330µF 4V 330µF 2.5V 220µF 6.3V NONE 330µF 4V 330µF 4V 220µF 6.3V NONE 330µF 4V 330µF 4V 220µF 6.3V NONE 330µF 4V 330µF 4V 220µF 6.3V NONE 330µF 4V 330µF 4V 220µF 6.3V NONE NONE NONE NONE COUT2 VENDORS SANYO POSCAP SANYO POSCAP SANYO POSCAP VIN (V) 5 5 5 5 12 12 12 12 5 5 5 5 12 12 12 12 5 5 5 5 12 12 12 12 5 5 5 5 12 12 12 12 7 7 7 7 12 12 12 12 12 15 20 DROOP (mV) 34 22 20 32 34 22 20 29.5 35 25 24 36 35 25 24 32.6 38 29.5 28 43 38 28 27 36.4 38 37.6 39.5 66 38 34.5 35.8 50 42 47 50 75 42 47 50 69 110 110 110 PART NUMBER 6TPE220MIL (220µF, 6.3V) 2R5TPE330M9 (330µF, 2.5V) 4TPE330MCL (330µF, 4V) PEAK TO PEAK (mV) 68 40 40 60 68 40 39 55 70 48 47.5 68 70 48 45 61.9 76 57.5 55 80 76 55 52 70 78 74 78.1 119 78 66.3 68.8 98 86 89 94 141 86 88 94 131 215 215 217 RECOVERY TIME (µs) 30 26 24 18 30 26 24 18 30 30 26 26 30 30 26 26 37 30 26 26 37 30 26 26 40 34 28 12 40 34 28 18 40 32 28 14 40 32 28 22 20 20 20 LOAD STEP (A/µs) 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 RFB (kΩ) 60.4 60.4 60.4 60.4 60.4 60.4 60.4 60.4 40.2 40.2 40.2 40.2 40.2 40.2 40.2 40.2 30.1 30.1 30.1 30.1 30.1 30.1 30.1 30.1 19.1 19.1 19.1 19.1 19.1 19.1 19.1 19.1 13.3 13.3 13.3 13.3 13.3 13.3 13.3 13.3 8.25 8.25 8.25 4606fb 18 LTM4606 Applications Information Table 3. 1.5V Output DERATING CURVE VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK θJA (°C/W) Figures 8, 10 5, 12 Figures 8, 10 5, 12 Figure 6 0 None 13.5 Figure 6 200 None 10 Figures 8, 10 Figures 9, 11 5, 12 Figure 6 400 None 9 5, 12 Figure 6 0 BGA Heat Sink 9.5 Figures 9, 11 5, 12 Figure 6 200 BGA Heat Sink 7 Figures 9, 11 5, 12 Figure 6 400 BGA Heat Sink 5 VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK θJA (°C/W) Table 4. 3.3V Output DERATING CURVE Figures 12, 14 12, 24 Figure 7 0 None 13.5 Figures 12, 14 12, 24 Figure 7 200 None 11 Figures 12, 14 12, 24 Figure 7 400 None 10 Figures 13, 15 12, 24 Figure 7 0 BGA Heat Sink 10 Figures 13, 15 12, 24 Figure 7 200 BGA Heat Sink 7 Figures 13, 15 12, 24 Figure 7 400 BGA Heat Sink 5 Heat Sink Manufacturer Wakefield Engineering Part No: LTN20069 Layout Checklist/Example The high integration of LTM4606 makes the PCB board layout very simple and easy. However, to optimize its electrical and thermal performance, some layout considerations are still necessary. • Use large PCB copper areas for high current path, including VIN, PGND and VOUT. It helps to minimize the PCB conduction loss and thermal stress. • Place high frequency ceramic input and output capacitors next to the VD, PGND and VOUT pins to minimize high frequency noise. • Place a dedicated power ground layer underneath the unit. • Use round corners for the PCB copper layer to minimize the radiated noise. Phone: 603-635-2800 • Use a separated SGND ground copper area for components connected to signal pins. Connect the SGND to PGND underneath the unit. • Place one or more high frequency ceramic capacitors close to the connection into the system board. Figure 17 gives a good example of the recommended layout. For load current below 3A, decouple the input and output grounds. Use vias to connect GND pads to the bottom layer, then connect to the right side of the module as the output GND. VIN CIN GND SIGNAL GND • To minimize the EMI noise and reduce module thermal stress, use multiple vias for interconnection between top layer and other power layers on different locations. • Do not put vias directly on pads, unless they are capped. CIN COUT COUT VOUT 4606 F17 Figure 17. Recommended PCB Layout 4606fb 19 LTM4606 Applications Information Frequency Adjustment The LTM4606 is designed to typically operate at 800kHz across most input conditions. The fSET pin is typically left open or decoupled with an optional 1000pF capacitor. The switching frequency has been optimized for maintaining constant output ripple noise over most operating ranges. The 800kHz switching frequency and the 400ns minimum off time can limit operation at higher duty cycles like 5V to 3.3V, and produce excessive inductor ripple currents for lower duty cycle applications like 28V to 5V. time. Figure 18 shows an operating range of 10V to 28V for 1MHz operation with a 150k resistor to ground, and an 8V to 16V operating range for fSET floating. These modifications are made to provide wider input voltage ranges for the 5V output designs while limiting the inductor ripple current, and maintaining the 400ns minimum off-time. Example for 3.3V Output LTM4606 minimum on-time = 100ns; tON = ((3.3 • 10pF)/IfSET) Example for 5V Output LTM4606 minimum off-time = 400ns; tOFF = t – tON, where t = 1/Frequency LTM4606 minimum on-time = 100ns; tON = ((4.8 • 10pF)/IfSET) Duty Cycle (DC) = tON/t or VOUT/VIN LTM4606 minimum off-time = 400ns; tOFF = t – tON, where t = 1/Frequency Duty Cycle = tON/t or VOUT/VIN Equations for setting frequency: IfSET = (VIN/(3 • RfSET)), where the internal RfSET is 41.2k. For 28V input operation, IfSET = 227µA. tON = ((4.8 • 10pF)/ IfSET), tON = 211ns. Frequency = (VOUT/(VIN • tON)) = (5V/ (28 • 211ns)) ~ 850kHz. The inductor ripple current begins to get high at the higher input voltages due to a larger voltage across the inductor. The current ripple is ~5A at 20% duty cycle if the integrated inductor is 1µH. The inductor ripple current can be lowered at the higher input voltages by adding an external resistor from fSET to ground to increase the switching frequency. A 4A ripple current is chosen, and the total peak current is equal to 1/2 of the 4A ripple current plus the output current. For 5V output, current is limited to 5A, so the total peak current is less than 7A. This is below the 8A peak specified value. A 150k resistor is placed from fSET to ground, and the parallel combination of 150k and 41.2k equates to 32.3k. The IfSET calculation with 32.3k and 28V input voltage equals 289µA. This equates to a tON of 166ns. This will increase the switching frequency from 850kHz to ~1MHz for the 28V to 5V conversion. The minimum on time is above 100ns at 28V input. Since the switching frequency is approximately constant over input and output conditions, then the lower input voltage range is limited to 8V for the 1MHz operation due to the 400ns minimum off time. Equation: tON = (VOUT/VIN) • (1/ Frequency) equates to a 375ns on time, and a 400ns off Equations for setting frequency: IfSET = (VIN/(3 • RfSET)), for 28V input operation, IfSET = 227µA, tON = ((3.3 • 10pF)/IfSET), tON = 145ns, where the internal RfSET is 41.2k. Frequency = (VOUT/(VIN • tON)) = (3.3V/(28 • 145ns)) ~ 810kHz. The minimum on-time and minimum-off time are within specification at 146ns and 1089ns. But the 4.5V minimum input for converting 3.3V output will not meet the minimum off-time specification of 400ns. tON = 905ns, Frequency = 810kHz, tOFF = 329ns. Solution Lower the switching frequency at lower input voltages to allow for higher duty cycles, and meet the 400ns minimum off-time at 4.5V input voltage. The off-time should be about 500ns with 100ns guard band. The duty cycle for (3.3V/4.5V) = ~73%. Frequency = (1 – DC)/tOFF or (1 – 0.73)/500ns = 540kHz. The switching frequency needs to be lowered to 540kHz at 4.5V input. tON = DC/ frequency, or 1.35µs. The fSET pin voltage compliance is 1/3 of VIN, and the IfSET current equates to 36µA with the internal 41.2k. The IfSET current needs to be 24µA for 540kHz operation. A resistor can be placed from VOUT to fSET to lower the effective IfSET current out of the fSET pin to 24µA. The fSET pin is 4.5V/3 =1.5V and VOUT = 3.3V, therefore a 150k resistor will source 12µA into the fSET node and lower the IfSET current to 24µA. This enables the 540kHz operation and the 4.5V to 28V input operation for down converting to 3.3V output as shown in Figure 19. The frequency will scale from 540kHz to 950kHz over this input range. This provides for an effective output current of 5A over the input range. 4606fb 20 LTM4606 Typical Applications VOUT 10V TO 28V C1 10µF R3 100k R4 100k VD VIN PLLIN VOUT PGOOD RUN LTM4606 VFB COMP INTVCC FCB DRVCC MARG0 fSET MARG1 TRACK/SS MPGM ON/OFF CIN 10µF 35V CERAMIC x2 TRACK/SS CONTROL SGND PGND RfSET 150k 5V AT 5A C2 100pF RFB 8.25k MARGIN CONTROL COUT1 22µF 6.3V + COUT2 220µF 6.3V REFER TO TABLE 2 FOR OUTPUT CAPACITOR SELECTIONS R1 392k 5% MARGIN IMPROVE EFFICIENCY FOR ≥12V INPUT 4606 TA02 Figure 18. 10V to 28VIN, 5V at 5A Design VOUT 4.5V TO 28V C1 10µF R3 100k R4 100k VD VIN PLLIN VOUT PGOOD RUN LTM4606 VFB COMP INTVCC FCB DRVCC MARG0 fSET MARG1 TRACK/SS MPGM SGND PGND ON/OFF CIN 10µF 35V CERAMIC x2 RfSET 150k VOUT TRACK/SS CONTROL 3.3V AT 5A C2 100pF RFB 13.3k MARGIN CONTROL R1 392k 5% MARGIN COUT1 22µF 6.3V x2 + COUT2 220µF 6.3V REFER TO TABLE 2 FOR OUTPUT CAPACITOR SELECTIONS 4606 TA03 Figure 19. 3.3V at 5A Design 4606fb 21 LTM4606 Typical Applications VOUT 4.5V TO 28V CLOCK SYNC C1 10µF R4 100k R3 100k ON/OFF CIN 10µF 35V CERAMIC x2 C4 0.01µF VD VIN PLLIN VOUT PGOOD RUN LTM4606 VFB COMP INTVCC FCB DRVCC MARG0 fSET MARG1 TRACK/SS MPGM SGND PGND 2.5V AT 6A C2 100pF RFB 19.1k COUT1 22µF 6.3V + COUT2 220µF 6.3V MARGIN CONTROL R1 392k 5% MARGIN 4606 TA04 Figure 20. Typical 4.5V to 28VIN, 2.5V at 6A Design VOUT VIN 4.5V TO 28V C1 10µF R4 100k + 2-PHASE OSCILLATOR R5 118k C7 0.1µF C5 100µF 35V R2 100k C2 10µF 35V C4 0.33µF V+ OUT1 GND OUT2 SET MOD CLOCK SYNC 0° PHASE VD VIN PLLIN PGOOD VOUT RUN LTM4606 VFB COMP FCB INTVCC DRVCC MARG0 fSET TRACK/SS MARG1 MPGM SGND PGND 2.5V AT 12A C6 220pF COUT1 22µF 6.3V + COUT2 220µF 6.3V MARGIN CONTROL R1 392k RFB 9.53k 5% MARGIN C3 10µF LTC6908-1 R3 100k C8 10µF 35V CLOCK SYNC 180° PHASE VD VIN PLLIN VOUT PGOOD RUN LTM4606 VFB COMP FCB INTVCC DRVCC fSET TRACK/SS SGND MARG0 MARG1 MPGM PGND COUT3 22µF 6.3V + COUT4 220µF 6.3V R6 392k 5% MARGIN 4606 TA05 Figure 21. 2-Phase, Parallel 2.5V at 12A Design 4606fb 22 LTM4606 Typical Applications 3.3V VIN 5V TO 28V C3 10µF R4 100k + 2-PHASE OSCILLATOR R5 118k C9 0.1µF C5 100µF 35V R2 100k C2 10µF 35V C7 0.15µF V+ OUT1 GND OUT2 SET MOD CLOCK SYNC 0° PHASE PLLIN VD VIN PGOOD VOUT RUN LTM4606 VFB COMP FCB INTVCC DRVCC MARG0 fSET TRACK/SS MARG1 MPGM SGND PGND R3 100k C4 10µF R7 100k C8 3.3V TRACK 10µF 35V R8 60.4k R9 19.1k COUT1 100µF 6.3V + COUT2 220µF 6.3V MARGIN CONTROL RFB1 13.3k R1 392k 5% MARGIN 3.3V LTC6908-1 3.3V AT 6A C6 22pF CLOCK SYNC 180° PHASE VD VIN PLLIN VOUT PGOOD RUN LTM4606 COMP INTVCC DRVCC fSET TRACK/SS SGND 2.5V AT 6A C1 22pF VFB FCB MARG0 MARG1 MPGM PGND COUT3 100µF 6.3V + COUT4 220µF 6.3V MARGIN CONTROL R6 392k RFB2 19.1k 4606 TA06 Figure 22. 2-Phase, 3.3V and 2.5V Outputs at 6A with Tracking and Margining 4606fb 23 LTM4606 Typical Applications 1.8V 4.5V TO 28V C3 10µF R4 100k + 2-PHASE OSCILLATOR R5 182k C9 0.1µF C5 100µF 35V R2 100k C2 10µF 35V C7 0.15µF V+ OUT1 GND OUT2 SET MOD CLOCK SYNC 0° PHASE VD VIN PLLIN PGOOD VOUT RUN LTM4606 VFB COMP FCB INTVCC DRVCC MARG0 fSET TRACK/SS MARG1 MPGM SGND PGND C4 10µF R3 100k C6 100pF COUT1 100µF 6.3V + COUT2 220µF 6.3V MARGIN CONTROL R1 392k RFB1 30.1k 5% MARGIN 1.8V LTC6908-1 1.8V AT 6A R7 100k C8 10µF 1.8V TRACK 35V R8 60.4k R9 40.2k CLOCK SYNC 180° PHASE VD VIN PLLIN VOUT PGOOD RUN LTM4606 VFB COMP FCB INTVCC DRVCC fSET TRACK/SS SGND MARG0 MARG1 MPGM PGND 1.5V AT 6A C1 100pF COUT3 22µF 6.3V + COUT4 220µF 6.3V MARGIN CONTROL R6 392k RFB2 40.2k 4606 TA07 Figure 23. 2-Phase, 1.8V and 1.5V Outputs at 6A with Tracking and Margining 4606fb 24 LTM4606 Package Description Pin Assignment Tables (Arranged by Pin Function) PIN NAME PIN NAME A1 A2 A3 A4 A5 A6 VIN VIN VIN VIN VIN VIN D1 D2 D3 D4 D5 D6 PGND PGND PGND PGND PGND PGND B1 B2 B3 B4 B5 B6 VIN VIN VIN VIN VIN VIN C1 C2 C3 C4 C5 C6 VIN VIN VIN VIN VIN VIN E1 E2 E3 E4 E5 E6 E7 E8 PGND PGND PGND PGND PGND PGND PGND PGND F1 F2 F3 F4 F5 F6 F7 F8 F9 PGND PGND PGND PGND PGND PGND PGND PGND PGND G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 PGND PGND PGND PGND PGND PGND PGND PGND PGND PGND PGND H1 H2 H3 H4 H5 H6 H7 H8 H9 H10 H11 PGND PGND PGND PGND PGND PGND PGND PGND PGND PGND PGND PIN NAME J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT K1 K2 K3 K4 K5 K6 K7 K8 K9 K10 K11 VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M11 VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT PIN NAME A7 A8 A9 A10 A11 A12 INTVCC PLLIN TRACK/SS RUN COMP MPGM B7 B8 B9 B10 B11 B12 VD RUN MPGM fSET C7 C8 C9 C10 C11 C12 VD DRVCC MARG1 MARG0 D7 D8 D9 D10 D11 D12 SGND COMP MARG1 E9 E10 E11 E12 DRVCC DRVCC F10 F11 F12 VFB G12 PGOOD H12 SGND J12 NC K12 NC L12 NC M12 FCB 4606fb 25 6.9850 5.7150 4.4450 3.1750 1.9050 0.6350 0.0000 0.6350 1.9050 3.1750 4.4450 5.7150 6.9850 4 PAD 1 CORNER 15 BSC PACKAGE TOP VIEW 3.1750 3.1750 SUGGESTED PCB LAYOUT TOP VIEW 1.9050 X 15 BSC Y DETAIL B 2.72 – 2.92 DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE LAND DESIGNATION PER JESD MO-222, SPP-010 SYMBOL TOLERANCE aaa 0.10 bbb 0.10 eee 0.05 6. THE TOTAL NUMBER OF PADS: 133 5. PRIMARY DATUM -Z- IS SEATING PLANE 4 3 2. ALL DIMENSIONS ARE IN MILLIMETERS 3 M L TRAY PIN 1 BEVEL COMPONENT PIN “A1” PADS SEE NOTES 1.27 BSC 13.97 BSC 0.12 – 0.28 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 DETAIL A 0.27 – 0.37 SUBSTRATE eee S X Y DETAIL B MOLD CAP 0.630 ±0.025 SQ. 133x aaa Z 2.45 – 2.55 bbb Z aaa Z 0.6350 0.0000 0.6350 (Reference LTC DWG # 05-08-1766 Rev Ø) Z 26 1.9050 LGA Package 133-Lead (15mm × 15mm × 2.82mm) K G F E LTMXXXXXX µModule PACKAGE BOTTOM VIEW H D C B LGA 133 1107 REV Ø A DETAIL A PACKAGE IN TRAY LOADING ORIENTATION J 13.97 BSC 1 2 3 4 5 6 7 8 9 10 11 12 C(0.30) PAD 1 LTM4606 Package Description 4606fb 6.9850 5.7150 4.4450 4.4450 5.7150 6.9850 LTM4606 Revision History REV DATE DESCRIPTION A 3/10 Change to Features. PAGE NUMBER Change to Absolute Maximum Ratings. B 3/11 1 2 Changes to Electrical Characteristics. 2, 3 Changes to Related Parts. 25 Text updated throughout the data sheet. Graph replaced on the front page, Figure 2, and Figure 16. 1-28 1, 12, 17 Added value of 1µH to inductor on Figure 1. 9 Updated Related Parts. 28 4606fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 27 LTM4606 Package Photograph Related Parts PART NUMBER DESCRIPTION COMMENTS LTM4601/ LTM4601A 12A DC/DC µModule Regulator with PLL, Output Tracking/Margining and Remote Sensing Synchronizable, PolyPhase Operation, LTM4601-1/LTM4601A-1 Version Has No Remote Sensing, LGA Package LTM4618 6A DC/DC µModule Regulator with PLL, Output Tracking 4.5V ≤ VIN ≤ 26.5V, 0.8V ≤ VOUT ≤ 5V, Synchronizable, 9mm × 15mm × 4.3mm LGA Package LTM4604A Low VIN 4A DC/DC µModule Regulator 2.375V ≤ VIN ≤ 5.5V, 0.8V ≤ VOUT ≤ 5V, 9mm × 15mm × 2.3mm LGA Package LTM4608A Low VIN 8A DC/DC µModule Regulator 2.375V ≤ VIN ≤ 5.5V, 0.6V ≤ VOUT ≤ 5V, 9mm × 15mm × 2.8mm LGA Package LTM4612 Low Noise 5A, 15VOUT DC/DC µModule Regulator Low Noise, with PLL, Output Tracking and Margining, LTM4606 Pin-Compatible LTM4627 15A DC/DC µModule Regulator 4.5V ≤ VIN ≤ 20V, 0.6V ≤ VOUT ≤ 5V, ±1.5% Total DC Output Accuracy, 15mm × 15mm × 4.32mm LGA Package EN55022 Class B Certified DC/DC µModule Regulators LTM8020 High VIN 0.2A DC/DC Step-Down µModule Regulator 4V ≤ VIN ≤ 36V, 1.25V ≤ VOUT ≤ 5V, 6.25mm × 6.25mm × 2.3mm LGA Package LTM8021 High VIN 0.5A DC/DC Step-Down µModule Regulator 3V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 5V, 6.25mm × 11.25mm × 2.8mm LGA Package LTM8022/ LTM8023 36VIN, 1A and 2A DC/DC µModule Regulators Pin Compatible, 4.5V ≤ VIN ≤ 36V, 9mm × 11.25mm × 2.8mm LGA Package LTM8031/ LTM8032 1A, 2A EMC DC/DC µModule Regulators EN55022 Class B Compliant, 3.6V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 10V, Pin Compatible, 9mm × 15mm × 2.82mm LGA Package LTM8033 3A EMC DC/DC µModule Regulator 3.6V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 24V, 11.25mm × 15mm × 4.32mm LGA Package 4606fb 28 Linear Technology Corporation LT 0311 REV B • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2008