LINEAR_DIMENSIONS LTM4601HVIVPBF

FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
Complete Switch Mode Power Supply
Wide Input Voltage Range: 4.5V to 28V
12A DC Typical, 14A Peak Output Current
0.6V to 5V Output Voltage
Output Voltage Tracking and Margining
Parallel Multiple µModule® Regulators for Current
Sharing
Differential Remote Sensing for Precision Regulation
PLL Frequency Synchronization
±1.5% Regulation
Current Foldback Protection (Disabled at Start-Up)
RoHS Compliant with Pb-Free Finish,
Gold Finish LGA (e4) or SAC 305 BGA (e1)
Ultrafast Transient Response
Current Mode Control
Up to 95% Efficiency at 5VIN, 3.3VOUT
Programmable Soft-Start
Output Overvoltage Protection
Small Footprint, Low Profile
(15mm × 15mm × 2.82mm) Surface Mount LGA and
(15mm × 15mm × 3.42mm) BGA Packages
APPLICATIONS
Telecom and Networking Equipment
Servers
n Industrial Equipment
n Point of Load Regulation
n
LTM4601HV
12A 28VIN DC/DC µModule
Regulator with PLL, Output
Tracking and Margining
DESCRIPTION
The LTM®4601HV is a complete 12A step-down switch
mode DC/DC power supply with onboard switching controller, MOSFETs, inductor and all support components. The
µModule regulator is housed in small surface mount 15mm
× 15mm × 2.82mm LGA and 15mm × 15mm × 3.42mm
BGA packages. Operating over an input voltage range of
4.5V to 28V, the LTM4601HV supports an output voltage
range of 0.6V to 5V as well as output voltage tracking
and margining. The high efficiency design delivers 12A
continuous current (14A peak). Only bulk input and output
capacitors are needed to complete the design.
The low profile and light weight package easily mounts
in unused space on the back side of PC boards for high
density point of load regulation. The µModule regulator
can be synchronized with an external clock for reducing
undesirable frequency harmonics and allows PolyPhase®
operation for high load currents.
A high switching frequency and adaptive on-time current
mode architecture deliver a very fast transient response
to line and load changes without sacrificing stability. An
onboard differential remote sense amplifier can be used
to accurately regulate an output voltage independent of
load current.
L, LT, LTC, LTM, Linear Technology, the Linear logo, µModule and PolyPhase are registered
trademarks and LTpowerCAD is a trademark of Linear Technology Corporation. All other
trademarks are the property of their respective owners. Protected by U.S. Patents including
5481178, 5847554, 6580258, 6304066, 6476589, 6774611, 6677210.
n
TYPICAL APPLICATION
Efficiency and Power Loss
vs Load Current
2.5V/12A Power Supply with 4.5V to 28V Input
95
CLOCK SYNC
TRACK/SS CONTROL
ON/OFF
CIN
R1
392k
5% MARGIN
RUN
COMP
INTVCC
DRVCC
MPGM
SGND
PLLIN TRACK/SS
VOUT
LTM4601HV
PGND
VFB
MARG0
MARG1
VOUT
2.5V
12A
100pF
MARGIN
CONTROL
COUT
VOUT_LCL
DIFFVOUT
VOSNS+
VOSNS–
fSET
5
85
24VIN
80
70
4601HV TA01a
3
24VIN
65
12VIN
60
2
POWER LOSS
55
RSET
19.1k
4
EFFICIENCY
75
1
50
45
POWER LOSS (W)
VIN
PGOOD
6
12VIN
90
EFFICIENCY (%)
VIN
4.5V TO 28V
0
2
8
6
4
10
LOAD CURRENT (A)
12
14
0
4601HV TA01b
4601hvfb
1
LTM4601HV
ABSOLUTE MAXIMUM RATINGS
(Note 1)
INTVCC, DRVCC, VOUT_LCL, VOUT (VOUT ≤ 3.3V with
Remote Sense Amp)..................................... –0.3V to 6V
PLLIN, TRACK/SS, MPGM, MARG0, MARG1,
PGOOD, fSET...............................–0.3V to INTVCC + 0.3V
RUN.............................................................. –0.3V to 5V
VFB, COMP................................................. –0.3V to 2.7V
VIN.............................................................. –0.3V to 28V
VOSNS+, VOSNS –...........................–0.3V to INTVCC + 0.3V
Operating Temperature Range (Note 2)....–40°C to 85°C
Junction Temperature............................................ 125°C
Storage Temperature Range................... –55°C to 125°C
fSET
VIN
MARG0
MARG1
MARG1
DRVCC
DRVCC
VFB
PGND
PGOOD
PGOOD
SGND
SGND
VOSNS+
VOSNS+
VOUT_LCL
DIFFVOUT
VOUT
VOUT_LCL
–
VOSNS–
VOSNS
BGA PACKAGE
118-LEAD (15mm × 15mm × 3.42mm)
LGA PACKAGE
118-LEAD (15mm × 15mm × 2.82mm)
TJMAX = 125°C, θJA = 15°C/W, θJC = 6°C/W,
θJA DERIVED FROM 95mm × 76mm PCB WITH 4 LAYERS
WEIGHT = 1.7g
MPGM
COMP
RUN
fSET
MARG0
DIFFVOUT
VOUT
TRACK/SS
VIN
VFB
PGND
PLLIN
INTVCC
MPGM
COMP
TOP VIEW
RUN
PLLIN
INTVCC
TOP VIEW
TRACK/SS
PIN CONFIGURATION
TJMAX = 125°C, θJA = 15.5°C/W, θJC = 6.5°C/W,
θJA DERIVED FROM 95mm × 76mm PCB WITH 4 LAYERS
WEIGHT = 1.9g
ORDER INFORMATION
LEAD FREE FINISH
TRAY
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTM4601HVEV#PBF
LTM4601HVEV#PBF
LTM4601HVV
118-Lead (15mm × 15mm × 2.82mm) LGA
–40°C to 85°C
LTM4601HVIV#PBF
LTM4601HVIV#PBF
LTM4601HVV
118-Lead (15mm × 15mm × 2.82mm) LGA
–40°C to 85°C
LTM4601HVEY#PBF
LTM4601HVEY#PBF
LTM4601HVY
118-Lead (15mm × 15mm × 3.42mm) BGA
–40°C to 85°C
LTM4601HVIY#PBF
LTM4601HVIY#PBF
LTM4601HVY
118-Lead (15mm × 15mm × 3.42mm) BGA
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
This product is only offered in trays. For more information go to: http://www.linear.com/packaging/
2
4601hvfb
LTM4601HV
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the –40°C to 85°C
temperature range (Note 2), otherwise specifications are at TA = 25°C, VIN = 12V, per typical application (front page) configuration,
RSET = 40.2k.
SYMBOL
PARAMETER
VIN(DC)
Input DC Voltage
VOUT(DC)
Output Voltage (With Remote
Sense Amp)
CONDITIONS
CIN = 10µF ×3, COUT = 200µF, RSET = 40.2k
VIN = 12V, VOUT = 1.5V, IOUT = 0
MIN
l
4.5
l
1.478
TYP
MAX
UNITS
28
V
1.5
1.522
V
4
V
Input Specifications
VIN(UVLO)
Undervoltage Lockout Threshold
IOUT = 0A
3.2
IINRUSH(VIN)
Input Inrush Current at Startup
IOUT = 0A. VOUT = 1.5V
VIN = 5V
VIN = 12V
0.6
0.7
A
A
IQ(VIN,NO LOAD)
Input Supply Bias Current
VIN = 12V, No Switching
VIN = 12V, VOUT = 1.5V, Switching Continuous
VIN = 5V, No Switching
VIN = 5V, VOUT = 1.5V, Switching Continuous
Shutdown, RUN = 0, VIN = 12V
3.8
38
2.5
42
22
mA
mA
mA
mA
µA
IS(VIN)
Input Supply Current
VIN = 12V, VOUT = 1.5V, IOUT = 12A
VIN = 12V, VOUT = 3.3V, IOUT = 12A
VIN = 5V, VOUT = 1.5V, IOUT = 12A
1.81
3.63
4.29
A
A
A
INTVCC
VIN = 12V, RUN > 2V
No Load
4.7
5
5.3
V
12
A
Output Specifications
IOUTDC
Output Continuous Current Range
VIN = 12V, VOUT = 1.5V (Note 5)
ΔVOUT(LINE)
VOUT
Line Regulation Accuracy
VOUT = 1.5V, IOUT = 0A, VIN from 4.5V to 28V
l
0.3
%
ΔVOUT(LOAD)
VOUT
Load Regulation Accuracy
VOUT = 1.5V, IOUT = 0A to 12A, with RSA (Note 5)
VIN = 5V
VIN = 12V
l
l
0.25
0.25
%
%
VOUT(AC)
Output Ripple Voltage
IOUT = 0A, COUT = 2× 100µF X5R Ceramic
VIN = 12V, VOUT = 1.5V
VIN = 5V, VOUT = 1.5V
20
18
mVP-P
mVP-P
fS
Output Ripple Voltage Frequency
IOUT = 5A, VIN = 12V, VOUT = 1.5V
850
kHz
ΔVOUT(START)
Turn-On Overshoot
COUT = 200µF, VOUT = 1.5V, IOUT = 0A,
TRACK/SS = 10nF
VIN = 12V
VIN = 5V
20
20
mV
mV
COUT = 200µF, VOUT = 1.5V, TRACK/SS = Open,
IOUT = 1A Resistive Load
VIN = 12V
VIN = 5V
0.5
0.5
ms
ms
Load: 0% to 50% to 0% of Full Load,
COUT = 2 × 22µF Ceramic, 470µF 4V Sanyo
POSCAP
VIN = 12V
VIN = 5V
35
35
mV
mV
25
µs
17
17
A
A
tSTART
ΔVOUTLS
Turn-On Time
Peak Deviation for Dynamic Load
tSETTLE
Settling Time for Dynamic Load Step Load: 0% to 50%, or 50% to 0% of Full Load
VIN = 12V
IOUTPK
Output Current Limit
COUT = 200µF Ceramic
VIN = 12V, VOUT = 1.5V
VIN = 5V, VOUT = 1.5V
0
4601hvfb
3
LTM4601HV
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the –40°C to 85°C
temperature range (Note 2), otherwise specifications are at TA = 25°C, VIN = 12V, per typical application (front page) configuration,
RSET = 40.2k.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Remote Sense Amp (Note 3)
VOSNS+, VOSNS– Common Mode Input Voltage Range VIN = 12V, RUN > 2V
CM Range
INTVCC – 1
V
0
INTVCC – 1
V
DIFFVOUT
Range
Output Voltage Range
VOS
Input Offset Voltage Magnitude
AV
Differential Gain
1
V/V
GBP
Gain Bandwidth Product
3
MHz
SR
Slew Rate
2
V/µs
20
kW
100
dB
RIN
Input Resistance
CMRR
Common Mode Rejection Mode
VIN = 12V, DIFFVOUT Load = 100k
0
1.25
+ to GND
VOSNS
mV
Control Stage
VFB
Error Amplifier Input Voltage
Accuracy
IOUT = 0A, VOUT = 1.5V
VRUN
RUN Pin On/Off Threshold
ITRACK/SS
Soft-Start Charging Current
VTRACK/SS = 0V
tON(MIN)
Minimum On Time
(Note 4)
tOFF(MIN)
Minimum Off Time
(Note 4)
RPLLIN
PLLIN Input Resistance
IDRVCC
Current into DRVCC Pin
l
0.594
0.6
0.606
V
1
1.5
1.9
V
–1.0
–1.5
–2.0
µA
50
100
ns
250
400
ns
50
VOUT = 1.5V, IOUT = 1A, DRVCC = 5V
60.098
kΩ
18
25
mA
60.4
60.702
kΩ
RFBHI
Resistor Between VOUT_LCL and VFB
VMPGM
Margin Reference Voltage
1.18
V
VMARG0,
VMARG1
MARG0, MARG1 Voltage Thresholds
1.4
V
PGOOD Output
ΔVFBH
PGOOD Upper Threshold
VFB Rising
7
10
13
%
ΔVFBL
PGOOD Lower Threshold
VFB Falling
–7
–10
–13
%
ΔVFB(HYS)
PGOOD Hysteresis
VFB Returning
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
4
1.5
%
Note 2: The LTM4601HV is tested under pulsed load conditions such
that TJ ≈ TA. The LTM4601HVE is guaranteed to meet performance
specifications from 0°C to 85°C. Specifications over the –40°C to 85°C
operating temperature range are assured by design, characterization
and correlation with statistical process controls. The LTM4601HVI is
guaranteed over the –40°C to 85°C temperature range.
Note 3: Remote sense amplifier recommended for ≤3.3V output.
Note 4: 100% tested at wafer level only.
Note 5: See output current derating curves for different VIN, VOUT and TA.
4601hvfb
LTM4601HV
TYPICAL PERFORMANCE CHARACTERISTICS
100
100
95
EFFICIENCY (%)
EFFICIENCY (%)
90
85
80
75
0.6VOUT
1.2VOUT
1.5VOUT
2.5VOUT
3.3VOUT
70
65
60
0
5
95
95
90
90
85
85
80
80
75
70
0.6VOUT
1.2VOUT
1.5VOUT
2.5VOUT
3.3VOUT
5VOUT
65
60
55
10
50
15
Efficiency vs Load Current
with 24VIN
Efficiency vs Load Current
with 12VIN
EFFICIENCY (%)
Efficiency vs Load Current
with 5VIN
(See Figures 19 and 20 for all curves)
0
LOAD CURRENT (A)
75
70
65
60
50
10
5
LOAD CURRENT (A)
4601HV G01
15
45
10
5
LOAD CURRENT (A)
0
4601HV G02
1.2V Transient Response
1.5V Transient Response
1.8V Transient Response
VOUT
50mV/DIV
VOUT
50mV/DIV
0A TO 6A
LOAD STEP
0A TO 6A
LOAD STEP
0A TO 6A
LOAD STEP
4601HV G04
20µs/DIV
1.5V AT 6A/µs LOAD STEP
COUT = 3 • 22µF 6.3V CERAMICS
470µF 4V SANYO POSCAP
C3 = 100pF
2.5V Transient Response
4601HV G05
20µs/DIV
1.8V AT 6A/µs LOAD STEP
COUT = 3 • 22µF 6.3V CERAMICS
470µF 4V SANYO POSCAP
C3 = 100pF
4601HV G06
3.3V Transient Response
VOUT
50mV/DIV
VOUT
50mV/DIV
0A TO 6A
LOAD STEP
0A TO 6A
LOAD STEP
20µs/DIV
2.5V AT 6A/µs LOAD STEP
COUT = 3 • 22µF 6.3V CERAMICS
470µF 4V SANYO POSCAP
C3 = 100pF
15
4601HV G03
VOUT
50mV/DIV
20µs/DIV
1.2V AT 6A/µs LOAD STEP
COUT = 3 • 22µF 6.3V CERAMICS
470µF 4V SANYO POSCAP
C3 = 100pF
1.5VOUT
2.5VOUT
3.3VOUT
5.0VOUT
55
4601HV G07
20µs/DIV
3.3V AT 6A/µs LOAD STEP
COUT = 3 • 22µF 6.3V CERAMICS
470µF 4V SANYO POSCAP
C3 = 100pF
4601 G08
4601hvfb
5
LTM4601HV
TYPICAL PERFORMANCE CHARACTERISTICS (See Figures 19 and 20 for all curves)
Start-Up, IOUT = 12A
(Resistive Load)
Start-Up, IOUT = 0A
VOUT
0.5V/DIV
VOUT
0.5V/DIV
IIN
1A/DIV
IIN
0.5A/DIV
5ms/DIV
VIN = 12V
VOUT = 1.5V
COUT = 470µF, 3 × 22µF
SOFT-START = 10nF
2ms/DIV
VIN = 12V
VOUT = 1.5V
COUT = 470µF, 3 × 22µF
SOFT-START = 10nF
4601HV G09
VIN to VOUT Step-Down Ratio
Track, IOUT = 12A
5.5
3.3V OUTPUT WITH
130k FROM VOUT
TO ION
5.0
OUTPUT VOLTAGE (V)
4.5
5V OUTPUT WITH
100k RESISTOR
ADDED FROM fSET
TO GND
4.0
3.5
3.0
2.0
5V OUTPUT WITH
NO RESISTOR ADDED
FROM fSET TO GND
1.5
2.5V OUTPUT
1.0
1.8V OUTPUT
0.5
1.5V OUTPUT
2.5
0
4601HV G10
TRACK/SS
0.5V/DIV
VFB
0.5V/DIV
VOUT
1V/DIV
2ms/DIV
VIN = 12V
VOUT = 1.5V
COUT = 470µF, 3 × 22µF
SOFT-START = 10nF
4601HV G12
1.2V OUTPUT
0
2
4
6
8 10 12 14 16 18 20 22 24
INPUT VOLTAGE (V)
4601HV G11
Short-Circuit Protection, IOUT = 0A
VOUT
0.5V/DIV
VOUT
0.5V/DIV
IIN
1A/DIV
IIN
1A/DIV
50µs/DIV
VIN = 12V
VOUT = 1.5V
COUT = 470µF, 3 × 22µF
SOFT-START = 10nF
6
Short-Circuit Protection, IOUT = 12A
4601HV G13
50µs/DIV
VIN = 12V
VOUT = 1.5V
COUT = 470µF, 3 × 22µF
SOFT-START = 10nF
4601HV G14
4601hvfb
LTM4601HV
PIN FUNCTIONS
(See Package Description for Pin Assignment)
VIN (Bank 1): Power Input Pins. Apply input voltage between these pins and PGND pins. Recommend placing
input decoupling capacitance directly between VIN pins
and PGND pins.
VOUT (Bank 3): Power Output Pins. Apply output load
between these pins and PGND pins. Recommend placing
output decoupling capacitance directly between these pins
and PGND pins. See Figure 17.
PGND (Bank 2): Power ground pins for both input and
output returns.
VOSNS– (Pin M12): (–) Input to the Remote Sense Amplifier. This pin connects to the ground remote sense point.
The remote sense amplifier is used for VOUT ≤3.3V. Tie to
INTVCC if not used.
VOSNS+ (Pin J12): (+) Input to the Remote Sense Amplifier. This pin connects to the output remote sense point.
The remote sense amplifier is used for VOUT ≤3.3V. Tie to
ground if not used.
DIFFVOUT (Pin K12): Output of the Remote Sense Amplifier. This pin connects to the VOUT_LCL pin. Leave floating
if remote sense amplifier is not used.
DRVCC (Pin E12): This pin normally connects to INTVCC
for powering the internal MOSFET drivers. This pin can be
biased up to 6V from an external supply with about 50mA
capability, or an external circuit as shown in Figure 18.
This improves efficiency at the higher input voltages by
reducing power dissipation in the module.
TRACK/SS (Pin A9): Output Voltage Tracking and SoftStart Pin. When the module is configured as a master
output, then a soft-start capacitor is placed on this pin
to ground to control the master ramp rate. A soft-start
capacitor can be used for soft-start turn on of a stand
alone regulator. Slave operation is performed by putting
a resistor divider from the master output to ground, and
connecting the center point of the divider to this pin. See
the Applications Information section.
MPGM (Pin A12): Programmable Margining Input. A resistor from this pin to ground sets a current that is equal
to 1.18V/R. This current multiplied by 10kΩ will equal a
value in millivolts that is a percentage of the 0.6V reference voltage. See Applications Information. To parallel
LTM4601HVs, each requires an individual MPGM resistor.
Do not tie MPGM pins together.
fSET (Pin B12): Frequency Set Internally to 850kHz. An
external resistor can be placed from this pin to ground
to increase frequency. See the Applications Information
section for frequency adjustment.
VFB (Pin F12): The Negative Input of the Error Amplifier.
Internally, this pin is connected to VOUT_LCL pin with a
60.4k precision resistor. Different output voltages can be
programmed with an additional resistor between VFB and
SGND pins. See the Applications Information section.
INTVCC (Pin A7): This pin is for additional decoupling of
the 5V internal regulator.
MARG0 (Pin C12): This pin is the LSB logic input for the
margining function. Together with the MARG1 pin it will
determine if margin high, margin low or no margin state
is applied. The pin has an internal pull-down resistor of
50k. See the Applications Information section.
PLLIN (Pin A8): External Clock Synchronization Input
to the Phase Detector. This pin is internally terminated
to SGND with a 50k resistor. Apply a clock with a high
level above 2V and below INTVCC. See the Applications
Information section.
MARG1 (Pin D12): This pin is the MSB logic input for the
margining function. Together with the MARG0 pin it will
determine if margin high, margin low or no margin state
is applied. The pin has an internal pull-down resistor of
50k. See the Applications Information section.
4601hvfb
7
LTM4601HV
PIN FUNCTIONS
(See Package Description for Pin Assignment)
SGND (Pin H12): Signal Ground. This pin connects to
PGND at output capacitor point. See Figure 17.
COMP (Pin A11): Current Control Threshold and Error
Amplifier Compensation Point. The current comparator
threshold increases with this control voltage. The voltage
ranges from 0V to 2.4V with 0.7V corresponding to zero
sense voltage (zero current).
PGOOD (Pin G12): Output Voltage Power Good Indicator.
Open-drain logic output that is pulled to ground when the
output voltage is not within ±10% of the regulation point,
after a 25µs power bad mask timer expires.
8
RUN (Pin A10): Run Control Pin. A voltage above 1.9V
will turn on the module, and when below 1V, will turn
off the module. A programmable UVLO function can be
accomplished by connecting to a resistor divider from
VIN to ground. See Figure 1. This pin has a 5.1V Zener to
ground. Maximum pin voltage is 5V. Limit current into the
RUN pin to less than 1mA.
VOUT_LCL (Pin L12): VOUT connects directly to this pin to
bypass the remote sense amplifier, or DIFFVOUT connects
to this pin when remote sense amplifier is used.
4601hvfb
LTM4601HV
SIMPLIFIED BLOCK DIAGRAM
VOUT_LCL
VIN
R1
UVLO
FUNCTION
>1.9V = ON
<1V = OFF
MAX = 5V
VOUT
1M
RUN
PGOOD
R2
5.1V
ZENER
COMP
1.5µF
VIN
4.5V TO 28V
+
CIN
60.4k
INTERNAL
COMP
Q1
POWER CONTROL
SGND
0.47µH
VOUT
2.5V
12A
MARG1
MARG0
22µF
VFB
50k
50k
Q2
fSET
MPGM
10k
TRACK/SS
CSS
COUT
2.2Ω
39.2k
PLLIN
50k
4.7µF
+
PGND
INTVCC
+
–
RSET
19.1k
VOSNS–
10k
10k
VOSNS+
10k
INTVCC
DIFFVOUT
DRVCC
4601HV F01
= SGND
= PGND
Figure 1. Simplified LTM4601HV Block Diagram
T
DECOUPLING
REQUIREMENTS A = 25°C, VIN = 12V. Use Figure 1 configuration.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
CIN
External Input Capacitor Requirement
(VIN = 4.5V to 28V, VOUT = 2.5V)
COUT
External Output Capacitor Requirement
(VIN = 4.5V to 28V, VOUT = 2.5V)
MAX
UNITS
IOUT = 12A, 3× 10µF Ceramics
20
30
µF
IOUT = 12A
100
200
µF
4601hvfb
9
LTM4601HV
OPERATION
Power Module Description
The LTM4601HV is a standalone nonisolated switching
mode DC/DC power supply. It can deliver up to 12A of
DC output current with some external input and output
capacitors. This module provides a precisely regulated
output voltage programmable via one external resistor
from 0.6VDC to 5.0VDC over a 4.5V to 28V wide input
voltage. The typical application schematics are shown in
Figures 19 and 20.
The LTM4601HV has an integrated constant on-time
current mode regulator, ultralow RDS(ON) FETs with fast
switching speed and integrated Schottky diodes. The typical
switching frequency is 850kHz at full load. With current
mode control and internal feedback loop compensation,
the LTM4601HV module has sufficient stability margins
and good transient performance under a wide range of
operating conditions and with a wide range of output
capacitors, even all ceramic output capacitors.
Current mode control provides cycle-by-cycle fast current
limit. Besides, foldback current limiting is provided in an
overcurrent condition while VFB drops. Internal overvoltage and undervoltage comparators pull the open-drain
PGOOD output low if the output feedback voltage exits a
±10% window around the regulation point. Furthermore,
10
in an overvoltage condition, internal top FET Q1 is turned
off and bottom FET Q2 is turned on and held on until the
overvoltage condition clears.
Pulling the RUN pin below 1V forces the controller into its
shutdown state, turning off both Q1 and Q2. At low load
current, the module works in continuous current mode by
default to achieve minimum output voltage ripple.
When DRVCC pin is connected to INTVCC an integrated
5V linear regulator powers the internal gate drivers. If a
5V external bias supply is applied on the DRVCC pin, then
an efficiency improvement will occur due to the reduced
power loss in the internal linear regulator. This is especially
true at the high end of the input voltage range.
The LTM4601HV has a very accurate differential remote
sense amplifier with very low offset. This provides for very
accurate output voltage sensing at the load. The MPGM
pin, MARG0 pin and MARG1 pin are used to support
voltage margining, where the percentage of margin is
programmed by the MPGM pin, and MARG0 and MARG1
select margining.
The PLLIN pin provides frequency synchronization of the
device to an external clock. The TRACK/SS pin is used
for power supply tracking and soft-start programming.
4601hvfb
LTM4601HV
APPLICATIONS INFORMATION
The typical LTM4601HV application circuits are shown in
Figures  19 and 20. External component selection is primarily determined by the maximum load current and output
voltage. Refer to Table 2 for specific external capacitor
requirements for a particular application.
The MPGM pin programs a current that when multiplied
by an internal 10k resistor sets up the 0.6V reference ±
offset for margining. A 1.18V reference divided by the
RPGM resistor on the MPGM pin programs the current.
Calculate VOUT(MARGIN):
VIN to VOUT Step-Down Ratios
There are restrictions in the maximum VIN to VOUT step
down ratio that can be achieved for a given input voltage.
These constraints are shown in the Typical Performance
Characteristics curves labeled VIN to VOUT Step-Down
Ratio. Note that additional thermal derating may apply. See
the Thermal Considerations and Output Current Derating
section of this data sheet.
Output Voltage Programming and Margining
The PWM controller has an internal 0.6V reference voltage.
As shown in the Block Diagram, a 1M and a 60.4k 0.5%
internal feedback resistor connects VOUT and VFB pins
together. The VOUT_LCL pin is connected between the 1M
and the 60.4k resistor. The 1M resistor is used to protect
against an output overvoltage condition if the VOUT_LCL
pin is not connected to the output, or if the remote sense
amplifier output is not connected to VOUT_LCL. In these
cases, the output voltage will default to 0.6V. Adding a
resistor RSET from the VFB pin to SGND pin programs
the output voltage:
VOUT = 0.6V
60.4k +RSET
RSET
%VOUT
• VOUT
100
where %VOUT is the percentage of VOUT you want to
margin, and VOUT(MARGIN) is the margin quantity in volts:
RPGM =
VOUT
1.18V
•
•10k
0.6V VOUT(MARGIN)
where RPGM is the resistor value to place on the MPGM
pin to ground.
The margining voltage, VOUT(MARGIN), will be added or
subtracted from the nominal output voltage as determined
by the state of the MARG0 and MARG1 pins. See the truth
table below:
MARG1
MARG0
MODE
LOW
LOW
NO MARGIN
LOW
HIGH
MARGIN UP
HIGH
LOW
MARGIN DOWN
HIGH
HIGH
NO MARGIN
Input Capacitors
LTM4601HV module should be connected to a low AC
impedance DC source. Input capacitors are required to
be placed adjacent to the module. In Figure 20, the 10µF
ceramic input capacitors are selected for their ability to
handle the large RMS current into the converter. An input
bulk capacitor of 100µF is optional. This 100µF capacitor
is only needed if the input source impedance is compromised by long inductive leads or traces.
or equivalently:
RSET =
VOUT(MARGIN) =
60.4k
 VOUT 
−1

0.6V 
Table 1. RSET Standard 1% Resistor Values vs VOUT
RSET
(kΩ)
Open
60.4
40.2
30.1
25.5
19.1
13.3
8.25
VOUT
(V)
0.6
1.2
1.5
1.8
2
2.5
3.3
5
For a buck converter, the switching duty-cycle can be
estimated as:
D=
VOUT
VIN
4601hvfb
11
LTM4601HV
APPLICATIONS INFORMATION
ICIN(RMS) =
IOUT(MAX)
η%
• D • (1–D)
In the above equation, η% is the estimated efficiency of
the power module. CIN can be a switcher-rated electrolytic
aluminum capacitor, OS-CON capacitor or high value ceramic capacitor. Note the capacitor ripple current ratings
are often based on temperature and hours of life. This
makes it advisable to properly derate the input capacitor,
or choose a capacitor rated at a higher temperature than
required. Always contact the capacitor manufacturer for
derating requirements.
In Figures 19 and 20, the 10µF ceramic capacitors are together used as a high frequency input decoupling capacitor.
In a typical 12A output application, three very low ESR, X5R
or X7R, 10µF ceramic capacitors are recommended. These
decoupling capacitors should be placed directly adjacent
to the module input pins in the PCB layout to minimize
the trace inductance and high frequency AC noise. Each
10µF ceramic is typically good for 2A to 3A of RMS ripple
current. Refer to your ceramics capacitor catalog for the
RMS current ratings.
Multiphase operation with multiple LTM4601HV devices in
parallel will lower the effective input RMS ripple current due
to the interleaving operation of the regulators. Application
Note 77 provides a detailed explanation. Refer to Figure 2
for the input capacitor ripple current reduction as a function of the number of phases. The figure provides a ratio
of RMS ripple current to DC load current as function of
duty cycle and the number of paralleled phases. Pick the
corresponding duty cycle and the number of phases to
arrive at the correct ripple current value. For example, the
2-phase parallel LTM4601HV design provides 24A at 2.5V
12
output from a 12V input. The duty cycle is DC = 2.5V/12V
= 0.21. The 2-phase curve has a ratio of ~0.25 for a duty
cycle of 0.21. This 0.25 ratio of RMS ripple current to a
DC load current of 24A equals ~6A of input RMS ripple
current for the external input capacitors.
Output Capacitors
The LTM4601HV is designed for low output ripple voltage.
The bulk output capacitors defined as COUT are chosen
with low enough effective series resistance (ESR) to meet
the output voltage ripple and transient requirements. COUT
can be a low ESR tantalum capacitor, a low ESR polymer
capacitor or a ceramic capacitor. The typical capacitance is
200µF if all ceramic output capacitors are used. Additional
output filtering may be required by the system designer
if further reduction of output ripple or dynamic transient
spike is required. Table 2 shows a matrix of different output
voltages and output capacitors to minimize the voltage
droop and overshoot during a 5A/µs transient. The table
optimizes total equivalent ESR and total bulk capacitance
to maximize transient performance.
0.6
RMS INPUT RIPPLE CURRENT
DC LOAD CURRENT
Without considering the inductor ripple current, the RMS
current of the input capacitor can be estimated as:
0.5
1-PHASE
2-PHASE
3-PHASE
4-PHASE
6-PHASE
12-PHASE
0.4
0.3
0.2
0.1
0
0.1
0.2
0.3 0.4 0.5 0.6 0.7
DUTY CYCLE (VOUT/VIN)
0.8
0.9
4601HV F02
Figure 2. Normalized Input RMS Ripple Current
vs Duty Cycle for One to Six Modules (Phases)
4601hvfb
LTM4601HV
APPLICATIONS INFORMATION
Multiphase operation with multiple LTM4601HV devices
in parallel will lower the effective output ripple current
due to the interleaving operation of the regulators. For
example, each LTM4601HV’s inductor current in a 12V
to 2.5V multiphase design can be read from the Inductor
12
2.5V OUTPUT
10
5V OUTPUT
1.8V OUTPUT
1.5V OUTPUT
1.2V OUTPUT
6
3.3V OUTPUT WITH
130k ADDED FROM
VOUT TO fSET
4
5V OUTPUT WITH
100k ADDED FROM
fSET TO GND
2
0
0.2
0.4
0.6
DUTY CYCLE (VOUT/VIN)
0.8
4601HV F03
Figure 3. Inductor Ripple Current vs Duty Cycle
Figure 4 provides a ratio of peak-to-peak output ripple current to the inductor current as a function of duty cycle and
the number of paralleled phases. Pick the corresponding
duty cycle and the number of phases to arrive at the correct
output ripple current ratio value. If a 2-phase operation is
chosen at a duty cycle of 21%, then 0.6 is the ratio. This
0.6 ratio of output ripple current to inductor ripple of 6A
equals 3.6A of effective output ripple current. Refer to
Application Note 77 for a detailed explanation of output
ripple current reduction as a function of paralleled phases.
The output ripple voltage has two components that are
related to the amount of bulk capacitance and effective
series resistance (ESR) of the output bulk capacitance.
1.00
0.95
1-PHASE
2-PHASE
3-PHASE
4-PHASE
6-PHASE
0.90
0.85
0.80
PEAK-TO-PEAK OUTPUT RIPPLE CURRENT
DIr
0
RATIO =
IL (A)
8
Ripple Current vs Duty Cycle graph (Figure 3). The large
ripple current at low duty cycle and high output voltage
can be reduced by adding an external resistor from fSET to
ground which increases the frequency. If the duty cycle is
DC = 2.5V/12V = 0.21, the inductor ripple current for 2.5V
output at 21% duty cycle is ~6A in Figure 3.
0.75
0.70
0.65
0.60
0.55
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9
DUTY CYCLE (VO/VIN)
4601HV F04
Figure 4. Normalized Output Ripple Current vs Duty Cycle, Dlr = VOT/LI, Dlr = Each Phase’s Inductor Current
4601hvfb
13
LTM4601HV
APPLICATIONS INFORMATION
Therefore, the output ripple voltage can be calculated with
the known effective output ripple current. The equation:
ΔVOUT(P-P) ≈ (ΔIL/(8 • f • m • COUT) + ESR • ΔIL), where f
is frequency and m is the number of parallel phases. This
calculation process can be easily accomplished by using
LTpowerCAD™.
Fault Conditions: Current Limit and Overcurrent
Foldback
LTM4601HV has a current mode controller, which inherently limits the cycle-by-cycle inductor current not only in
steady-state operation, but also in response to transients.
To further limit current in the event of an overload condition, the LTM4601HV provides foldback current limiting.
If the output voltage falls by more than 50%, then the
maximum output current is progressively lowered to
about one sixth of its full current limit value. The current
limit returns to its nominal value once VOUT and VFB have
returned to their nominal values.
Soft-Start and Tracking
Output voltage tracking can be programmed externally
using the TRACK/SS pin. The output can be tracked up and
down with another regulator. The master regulator’s output
is divided down with an external resistor divider that is the
same as the slave regulator’s feedback divider. Figure 5
shows an example of coincident tracking. Ratiometric
modes of tracking can be achieved by selecting different
resistor values to change the output tracking ratio. The
master output must be greater than the slave output for
the tracking to work. Figure 6 shows the coincident output
tracking characteristics.
MASTER
OUTPUT
TRACK CONTROL
VIN
100k
)
t SOFTSTART = 0.8 • 0.6V ± VOUT(MARGIN) •
VIN
PGOOD
SGND
PLLIN TRACK/SS
VOUT
LTM4601HV
PGND
SLAVE OUTPUT
VFB
MARG0
MARG1
COUT
VOUT_LCL
DIFFVOUT
VOSNS+
VOSNS–
fSET
RSET
40.2k
4601HV F05
Figure 5. Coincident Tracking Schematic
CSS
1.5µA
When the RUN pin falls below 1.5V, then the TRACK/SS
pin is reset to allow for proper soft-start control when the
regulator is enabled again. Current foldback and forced
continuous mode are disabled during the soft-start process. The soft-start function can also be used to control
the output ramp up time, so that another regulator can
be easily tracked to it.
R2
60.4k
R1
40.2k
MPGM
RUN
COMP
INTVCC
DRVCC
CIN
The TRACK/SS pin provides a means to either soft-start
the regulator or track it to a different power supply. A
capacitor on this pin will program the ramp rate of the
output voltage. A 1.5µA current source will charge up the
external soft-start capacitor to 80% of the 0.6V internal
voltage reference plus or minus any margin delta. This will
control the ramp of the internal reference and the output
voltage. The total soft-start time can be calculated as:
(
Output Voltage Tracking
MASTER OUTPUT
SLAVE OUTPUT
OUTPUT
VOLTAGE
TIME
4601HV F06
Figure 6. Coincident Output Tracking Characteristics
14
4601hvfb
LTM4601HV
APPLICATIONS INFORMATION
Run Enable
INTVCC and DRVCC Connection
The RUN pin is used to enable the power module. The
pin has an internal 5.1V Zener to ground. The pin can be
driven with a logic input not to exceed 5V.
An internal low dropout regulator produces an internal
5V supply that powers the control circuitry and DRVCC
for driving the internal power MOSFETs. Therefore, if the
system does not have a 5V power rail, the LTM4601HV
can be directly powered by VIN. The gate driver current
through the LDO is about 20mA. The internal LDO power
dissipation can be calculated as:
The RUN pin can also be used as an undervoltage lock out
(UVLO) function by connecting a resistor divider from the
input supply to the RUN pin:
VUVLO =
R1+R2
•1.5V
R2
See Figure 1, Simplified Block Diagram.
Power Good
The PGOOD pin is an open-drain pin that can be used to
monitor valid output voltage regulation. This pin monitors
a ±10% window around the regulation point and tracks
with margining.
COMP Pin
This pin is the external compensation pin. The module
has already been internally compensated for most output
voltages. Table 2 is provided for most application requirements. LTpowerCAD is available for other control loop
optimization.
PLDO_LOSS = 20mA • (VIN – 5V)
The LTM4601HV also provides the external gate driver
voltage pin DRVCC. If there is a 5V rail in the system, it is
recommended to connect DRVCC pin to the external 5V
rail. This is especially true for higher input voltages. Do
not apply more than 6V to the DRVCC pin. A 5V output can
be used to power the DRVCC pin with an external circuit
as shown in Figure 18.
Parallel Operation of the Module
The LTM4601HV device is an inherently current mode
controlled device. Parallel modules will have very good
current sharing. This will balance the thermals on the
design. The voltage feedback equation changes with the
variable N as modules are paralleled:
PLLIN
The power module has a phase-locked loop comprised
of an internal voltage controlled oscillator and a phase
detector. This allows the internal top MOSFET turn-on
to be locked to the rising edge of the external clock. The
frequency range is ±30% around the operating frequency
of 850kHz. A pulse detection circuit is used to detect a
clock on the PLLIN pin to turn on the phase-locked loop.
The pulse width of the clock has to be at least 400ns and
at least 2V in amplitude. The PLLIN pin must be driven
from a low impedance source such as a logic gate located
close to the pin. During the start-up of the regulator, the
phase-locked loop function is disabled.
60.4k
+ R SET
VOUT = 0.6V • N
R SET
or equivalently:
60.4k
N
R SET =
V
 OUT 
− 1

0.6V 
where N is the number of paralleled modules.
Figure 21 shows two LTM4601HV modules used in a parallel design. An LTM4601HV device can be used without
the remote sense amplifier.
4601hvfb
15
LTM4601HV
APPLICATIONS INFORMATION
Thermal Considerations and Output Current Derating
The power loss curves in Figures 7 and 8 can be used
in coordination with the load current derating curves in
Figures 9 to 16 for calculating an approximate θJA for the
module with various heat sinking methods. Thermal models
are derived from several temperature measurements at
the bench and thermal modeling analysis. Thermal Application Note 103 provides a detailed explanation of the
analysis for the thermal models and the derating curves.
Tables 3 and 4 provide a summary of the equivalent θJA
for the noted conditions. These equivalent θJA parameters
are correlated to the measured values, and are improved
with air flow. The case temperature is maintained at 100°C
or below for the derating curves. The maximum case
temperature of 100°C is to allow for a rise of about 13°C
to 25°C inside the µModule with a thermal resistance θJC
from junction to case between 6°C/W to 9°C/W. This will
maintain the maximum junction temperature inside the
µModule below 125°C.
Safety Considerations
The LTM4601HV modules do not provide isolation from
VIN to VOUT. There is no internal fuse. If required, a
slow blow fuse with a rating twice the maximum input
current needs to be provided to protect each unit from
catastrophic failure.
6
5.0
4.5
5
24VIN
3.5
3.0
POWER LOSS (W)
POWER LOSS (W)
4.0
12VIN
2.5
2.0
1.5
24VIN
3
12VIN
2
5VIN
1.0
1
0.5
0
4
0
2
6
8
4
LOAD CURRENT (A)
10
0
12
0
2
4
6
8
LOAD CURRENT (A)
10
4601HV F08
4601HV F07
Figure 8. 3.3VOUT Power Loss
12
12
10
10
MAXIMUM LOAD CURRENT (A)
MAXIMUM LOAD CURRENT (A)
Figure 7. 1.5VOUT Power Loss
8
6
4
5VIN, 1.5VOUT 0LFM
5VIN, 1.5VOUT 200LFM
5VIN, 1.5VOUT 400LFM
2
0
50
100
60
70
80
90
AMBIENT TEMPERATURE (°C)
4601HV F09
Figure 9. No Heat Sink 5VIN
16
12
8
6
4
5VIN, 1.5VOUT 0LFM
5VIN, 1.5VOUT 200LFM
5VIN, 1.5VOUT 400LFM
2
0
50
100
60
70
80
90
AMBIENT TEMPERATURE (°C)
4601HV F10
Figure 10. BGA Heat Sink 5VIN
4601hvfb
LTM4601HV
12
12
10
10
MAXIMUM LOAD CURRENT (A)
MAXIMUM LOAD CURRENT (A)
APPLICATIONS INFORMATION
8
6
4
12VIN, 1.5VOUT 0LFM
12VIN, 1.5VOUT 200LFM
12VIN, 1.5VOUT 400LFM
2
0
50
6
4
12VIN, 1.5VOUT 0LFM
12VIN, 1.5VOUT 200LFM
12VIN, 1.5VOUT 400LFM
2
0
100
60
70
80
90
AMBIENT TEMPERATURE (°C)
8
50
4601HV F12
4601HV F11
Figure 12. BGA Heat Sink 12VIN
12
12
10
10
MAXIMUM LOAD CURRENT (A)
MAXIMUM LOAD CURRENT (A)
Figure 11. No Heat Sink 12VIN
8
6
4
0LFM
200LFM
400LFM
2
0
40
60
80
AMBIENT TEMPERATURE (°C)
8
6
4
0
100
0LFM
200LFM
400LFM
2
40
60
80
AMBIENT TEMPERATURE (°C)
Figure 14. 12VIN, 3.3VOUT, BGA Heat Sink
12
12
10
10
MAXIMUM LOAD CURRENT (A)
MAXIMUM LOAD CURRENT (A)
Figure 13. 12VIN, 3.3VOUT, No Heat Sink
8
6
4
24VIN, 1.5VOUT 0LFM
24VIN, 1.5VOUT 200LFM
24VIN, 1.5VOUT 400LFM
0
40
60
80
AMBIENT TEMPERATURE (°C)
100
4601HV F15
Figure 15. 24VIN, 1.5VOUT, No Heat Sink
100
4601HV F14
4601HV F13
2
100
60
70
80
90
AMBIENT TEMPERATURE (°C)
8
6
4
24VIN, 1.5VOUT 0LFM
24VIN, 1.5VOUT 200LFM
24VIN, 1.5VOUT 400LFM
2
0
40
60
80
AMBIENT TEMPERATURE (°C)
100
4601HV F16
Figure 16. 24VIN, 1.5VOUT, BGA Heat Sink
4601hvfb
17
LTM4601HV
APPLICATIONS INFORMATION
Table 2. Output Voltage Response Versus Component Matrix* (Refer to Figures 19 and 20), 0A to 6A Load Step
TYPICAL MEASURED VALUES
PART NUMBER
COUT1 VENDORS
TDK
C4532X5R0J107MZ (100µF, 6.3V)
TAIYO YUDEN
JMK432BJ107MU-T (100µF, 6.3V)
TAIYO YUDEN
JMK316BJ226ML-T501 (22µF, 6.3V)
VOUT
(V)
1.2
1.2
PART NUMBER
6TPE330MIL (330µF, 6.3V)
2R5TPE470M9 (470µF, 2.5V)
4TPE470MCL (470µF, 4V)
2 × 10µF 35V
CIN
(BULK)
150µF 35V
COUT1
(CERAMIC)
3 × 22µF 6.3V
COUT2
(BULK)
470µF 4V
CCOMP
NONE
C3
47pF
VIN
(V)
5
DROOP
(mV)
70
PEAK TO
PEAK (mV)
140
RECOVERY
TIME (µs)
30
LOAD STEP
(A/µs)
6
RSET
(kΩ)
60.4
2 × 10µF 35V
150µF 35V
1 × 100µF 6.3V
470µF 2.5V
NONE
100pF
5
35
70
20
6
60.4
1.2
2 × 10µF 35V
150µF 35V
2 × 100µF 6.3V
330µF 6.3V
NONE
22pF
5
70
140
20
6
60.4
1.2
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
2 × 10µF 35V
150µF 35V
4 × 100µF 6.3V
NONE
NONE
100pF
5
40
93
30
6
60.4
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
150µF 35V
3 × 22µF 6.3V
1 × 100µF 6.3V
2 × 100µF 6.3V
4 × 100µF 6.3V
3 × 22µF 6.3V
1 × 100µF 6.3V
2 × 100µF 6.3V
4 × 100µF 6.3V
3 × 22µF 6.3V
1 × 100µF 6.3V
2 × 100µF 6.3V
4 × 100µF 6.3V
3 × 22µF 6.3V
1 × 100µF 6.3V
2 × 100µF 6.3V
4 × 100µF 6.3V
3 × 22µF 6.3V
1 × 100µF 6.3V
2 × 100µF 6.3V
4 × 100µF 6.3V
1 × 100µF 6.3V
2 × 100µF 6.3V
3 × 22µF 6.3V
4 × 100µF 6.3V
1 × 100µF 6.3V
3 × 22µF 6.3V
2 × 100µF 6.3V
4 × 100µF 6.3V
2 × 100µF 6.3V
1 × 100µF 6.3V
3 × 22µF 6.3V
4 × 100µF 6.3V
1 × 100µF 6.3V
3 × 22µF 6.3V
2 × 100µF 6.3V
4 × 100µF 6.3V
4 × 100µF 6.3V
4 × 100µF 6.3V
470µF 4V
470µF 2.5V
330µF 6.3V
NONE
470µF 4V
470µF 2.5V
330µF 6.3V
NONE
470µF 4V
470µF 2.5V
330µF 6.3V
NONE
470µF 4V
470µF 2.5V
330µF 6.3V
NONE
470µF 4V
470µF 2.5V
330µF 6.3V
NONE
470µF 4V
330µF 6.3V
470µF 4V
NONE
470µF 4V
470µF 4V
330µF 6.3V
NONE
330µF 6.3V
470µF 4V
470µF 4V
NONE
470µF 4V
470µF 4V
330µF 6.3V
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
100pF
100pF
22pF
100pF
100pF
33pF
100pF
100pF
100pF
33pF
100pF
100pF
47pF
100pF
100pF
100pF
100pF
100pF
100pF
100pF
100pF
220pF
NONE
100pF
100pF
NONE
220pF
220pF
100pF
100pF
100pF
100pF
100pF
150pF
100pF
100pF
22pF
22pF
12
12
12
12
5
5
5
5
12
12
12
12
5
5
5
5
12
12
12
12
5
5
5
5
12
12
12
12
7
7
7
7
12
12
12
12
15
20
70
35
70
49
48
54
44
61
48
54
44
54
48
44
68
65
60
60
68
65
48
56
57
60
48
51
56
70
120
110
110
114
110
110
110
114
188
159
140
70
140
98
100
109
84
118
100
109
89
108
100
90
140
130
120
120
140
130
103
113
116
115
103
102
113
140
240
214
214
230
214
214
214
230
375
320
30
20
20
20
35
30
30
30
35
30
25
25
30
20
30
30
30
30
30
20
30
30
30
25
30
30
30
25
30
30
30
30
30
35
35
30
25
25
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
60.4
60.4
60.4
60.4
40.2
40.2
40.2
40.2
40.2
40.2
40.2
40.2
30.1
30.1
30.1
30.1
30.1
30.1
30.1
30.1
19.1
19.1
19.1
19.1
19.1
19.1
19.1
19.1
13.3
13.3
13.3
13.3
13.3
13.3
13.3
13.3
8.25
8.25
1.2
1.2
1.2
1.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
5
5
CIN
(CERAMIC)
COUT2 VENDORS
SANYO POSCAP
SANYO POSCAP
SANYO POSCAP
* X7R is recommended for extended temperature range.
18
4601hvfb
LTM4601HV
APPLICATIONS INFORMATION
Table 3. 1.5V Output at 12A
DERATING CURVE
VIN (V)
POWER LOSS CURVE
AIR FLOW (LFM)
HEAT SINK
qJA (°C/W) LGA
qJA (°C/W) BGA
Figures 9, 11, 15
5, 12, 24
Figure 7
0
None
15.2
15.7
Figures 9, 11, 15
5, 12, 24
Figure 7
200
None
14
14.5
Figures 9, 11, 15
5, 12, 24
Figure 7
400
None
12
12.5
Figures 10, 12, 16
5, 12, 24
Figure 7
0
BGA Heat Sink
13.9
14.4
Figures 10, 12, 16
5, 12, 24
Figure 7
200
BGA Heat Sink
11.3
11.8
Figures 10, 12, 16
5, 12, 24
Figure 7
400
BGA Heat Sink
10.25
10.75
POWER LOSS CURVE
AIR FLOW (LFM)
HEAT SINK
qJA (°C/W) LGA
qJA (°C/W) BGA
Table 4. 3.3V Output at 12A
DERATING CURVE
VIN (V)
Figure 13
12
Figure 8
0
None
15.2
15.7
Figure 13
12
Figure 8
200
None
14.6
15.0
Figure 13
12
Figure 8
400
None
13.4
13.9
Figure 14
12
Figure 8
0
BGA Heat Sink
13.9
14.4
Figure 14
12
Figure 8
200
BGA Heat Sink
11.1
11.6
Figure 14
12
Figure 8
400
BGA Heat Sink
10.5
11.0
Heat Sink Manufacturer
Aavid Thermalloy
Part No: 375424B00034G
Phone: 603-224-9988
4601hvfb
19
LTM4601HV
APPLICATIONS INFORMATION
Layout Checklist/Example
Frequency Adjustment
The high integration of LTM4601HV makes the PCB board
layout very simple and easy. However, to optimize its electrical and thermal performance, some layout considerations
are still necessary.
The LTM4601HV is designed to typically operate at 850kHz
across most input conditions. The fSET pin is normally
left open. The switching frequency has been optimized
for maintaining constant output ripple noise over most
operating ranges. The 850kHz switching frequency and
the 400ns minimum off time can limit operation at higher
duty cycles like 5V to 3.3V, and produce excessive inductor ripple currents for lower duty cycle applications like
28V to 5V. The 5VOUT and 3.3VOUT drop out curves are
modified by adding an external resistor on the fSET pin to
allow for lower input voltage operation, or higher input
voltage operation.
• Use large PCB copper areas for high current path, including VIN, PGND and VOUT. It helps to minimize the
PCB conduction loss and thermal stress.
• Place high frequency ceramic input and output capacitors next to the VIN, PGND and VOUT pins to minimize
high frequency noise.
• Place a dedicated power ground layer underneath the
unit. Refer frequency synchronization source to power
ground.
Example for 5V Output
• To minimize the via conduction loss and reduce module
thermal stress, use multiple vias for interconnection
between top layer and other power layers.
LTM4601HV minimum on-time = 100ns
tON = ((VOUT • 10pF)/IfSET), for VOUT > 4.8V use 4.8V
• Do not put vias directly on pads unless they are capped.
tOFF = t – tON, where t = 1/Frequency
• Use a separated SGND copper area for components
connected to signal pins. Connect the SGND to PGND
underneath the unit.
Duty Cycle = tON/t or VOUT/VIN
Figure 17 gives a good example of the recommended layout.
VIN
CIN
CIN
GND
SIGNAL
GND
COUT
COUT
VOUT
4601HV F17
Figure 17. Recommended Layout (LGA and BGA
PCB Layouts Are Identical with the Exception of
Circle Pads for BGA. See Package Description.)
20
LTM4601HV minimum off-time = 400ns
Equations for setting frequency:
IfSET = (VIN /(3 • RfSET)), for 28V operation, IfSET = 238µA,
tON = ((4.8 • 10pF)/IfSET), tON = 202ns, where the internal
RfSET is 39.2k. Frequency = (VOUT/(VIN • tON)) = (5V/(28
• 202ns)) ~ 884kHz. The inductor ripple current begins to
get high at the higher input voltages due to a larger voltage
across the inductor. This is noted in the Typical Inductor
Ripple Current vs Duty Cycle graph (Figure 3) where IL ≈
10A at 20% duty cycle. The inductor ripple current can be
lowered at the higher input voltages by adding an external
resistor from fSET to ground to increase the switching
frequency. A 7A ripple current is chosen, and the total
peak current is equal to 1/2 of the 7A ripple current plus
the output current. The 5V output current is limited to 8A,
so the total peak current is less than 11.5A. This is below
the 14A peak specified value. A 100k resistor is placed
from fSET to ground, and the parallel combination of 100k
and 39.2k equates to 28k. The IfSET calculation with 28k
and 28V input voltage equals 333µA. This equates to a
tON of 144ns. This will increase the switching frequency
from ~884kHz to ~1.24MHz for the 28V to 5V conversion.
4601hvfb
LTM4601HV
APPLICATIONS INFORMATION
The minimum on-time is above 100ns at 28V input. Since
the switching frequency is approximately constant over
input and output conditions, then the lower input voltage
range is limited to 10V for the 1.24MHz operation due to
the 400ns minimum off-time. Equation: tON = (VOUT/VIN)
• (1/Frequency) equates to a 400ns on-time, and a 400ns
off-time. The “VIN to VOUT Step-Down Ratio Curve” reflects
an operating range of 10V to 28V for 1.24MHz operation
with a 100k resistor to ground as shown in Figure 18, and
an 8V to 16V operation for fSET floating. These modifications are made to provide wider input voltage ranges for
the 5V output designs while limiting the inductor ripple
current, and maintaining the 400ns minimum off-time.
off-time are within specification at 139ns and 1037ns. The
4.5V minimum input for converting 3.3V output will not
meet the minimum off-time specification of 400ns. tON =
868ns, Frequency = 850kHz, tOFF = 315ns.
Solution
Lower the switching frequency at lower input voltages to
allow for higher duty cycles, and meet the 400ns minimum
off-time at 4.5V input voltage. The off-time should be about
500ns, which includes a 100ns guard band. The duty cycle
for (3.3V/4.5V) = ~73%. Frequency = (1 – DC)/tOFF or
(1 – 0.73)/500ns = 540kHz. The switching frequency
needs to be lowered to 540kHz at 4.5V input. tON = DC/
frequency, or 1.35µs. The fSET pin voltage compliance
is 1/3 of VIN, and the IfSET current equates to 38µA with
the internal 39.2k. The IfSET current needs to be 24µA for
540kHz operation. As shown in Figure 19, a resistor can
be placed from VOUT to fSET to lower the effective IfSET
current out of the fSET pin to 24µA. The fSET pin is 4.5V/3
=1.5V and VOUT = 3.3V, therefore 130k will source 14µA
into the fSET node and lower the IfSET current to 24µA.
This enables the 540kHz operation and the 4.5V to 28V
input operation for down converting to 3.3V output. The
frequency will scale from 540kHz to 1.1 MHz over this
input range. This provides for an effective output current
of 8A over the input range.
Example for 3.3V Output
LTM4601HV minimum on-time = 100ns
tON = ((VOUT • 10pF)/IfSET)
LTM4601HV minimum off-time = 400ns
tOFF = t – tON, where t = 1/Frequency
Duty Cycle (DC) = tON /t or VOUT/VIN
Equations for setting frequency:
IfSET = (VIN /(3 • RfSET)), for 28V operation, IfSET = 238µA,
tON = ((3.3 • 10pF)/I fSET), tON = 138.7ns, where the internal
RfSET is 39.2k. Frequency = (VOUT /(VIN • tON)) = (3.3V/(28 •
138.7ns)) ~ 850kHz. The minimum on-time and minimum
VOUT
VIN
10V TO 28V
R2
100k
TRACK/SS CONTROL
R4
100k
MPGM
RUN
COMP
INTVCC
DRVCC
5% MARGIN
C2
10µF
35V
VIN
PGOOD
R1
392k
1%
C1
10µF
35V
SGND
PLLIN TRACK/SS
VOUT
LTM4601HV
PGND
REVIEW TEMPERATURE
DERATING CURVE
+
VFB
MARG0
MARG1
VOUT_LCL
DIFFVOUT
VOSNS+
VOSNS–
C3
100µF
6.3V
SANYO
POSCAP
VOUT
5V
8A
22µF
6.3V
REFER TO
TABLE 2
fSET
RfSET
100k
RSET
8.25k
MARGIN CONTROL
IMPROVE
EFFICIENCY
FOR ≥12V INPUT
SOT-323
DUAL
CMSSH-3C3
4601HV F18
Figure 18. 5V at 8A Design Without Differential Amplifier
4601hvfb
21
LTM4601HV
APPLICATIONS INFORMATION
VOUT
VIN
4.5V TO 16V
R2
100k
R4
100k
PGOOD
C2
10µF
25V
×3
TRACK/SS CONTROL
VIN
PGOOD
MPGM
RUN
COMP
INTVCC
DRVCC
LTM4601HV
R1
392k
SGND
REVIEW TEMPERATURE
DERATING CURVE
PLLIN TRACK/SS
VOUT
+
VOUT_LCL
DIFFVOUT
VOSNS+
VOSNS–
RfSET
130k
fSET
PGND
5% MARGIN
VFB
MARG0
MARG1
MARGIN CONTROL
VOUT
3.3V
10A
22µF
6.3V
C3
100µF
6.3V
SANYO
POSCAP
RSET
13.3k
4601HV F19
Figure 19. 3.3V at 10A Design
CLOCK SYNC
C5
0.01µF
VOUT
VIN
22V TO 28V
R2
100k
R4
100k
PGOOD
ON/OFF
CIN
BULK
OPT
+
CIN
10µF
35V
×3 CER
VIN
PGOOD
MPGM
RUN
COMP
INTVCC
DRVCC
PLLIN TRACK/SS
VOUT
LTM4601HV
R1
392k
5% MARGIN
SGND
PGND
VFB
MARG0
MARG1
VOUT_LCL
DIFFVOUT
VOSNS+
VOSNS–
fSET
REVIEW TEMPERATURE
DERATING CURVE
C3 100pF
COUT1
100µF
6.3V
MARGIN
CONTROL
RfSET
175k
VIN
RSET
40.2k
4601HV F20
+
COUT2
470µF
6.3V
VOUT
1.5V
10A
REFER TO
TABLE 2 FOR
DIFFERENT
OUTPUT
VOLTAGE
Figure 20. Typical 22V to 28V, 1.5V at 10A Design, 500kHz
22
4601hvfb
LTM4601HV
APPLICATIONS INFORMATION
VOUT
VIN
6V TO 28V
118k
1%
R2
100k
+
C1
0.1µF
LTC6908-1
1
2
3
V+
OUT1
GND
OUT2
SET
MOD
6
5
4
CLOCK SYNC
0° PHASE
C5*
100µF
35V
C2
10µF
35V
×2
R4
100k
MPGM
RUN
COMP
INTVCC
DRVCC
R1
392k
PLLIN TRACK/SS
VOUT
VIN
PGOOD
LTM4601HV
SGND
PGND
5%
MARGIN
2-PHASE
OSCILLATOR
VFB
MARG0
MARG1
TRACK/SS CONTROL
C6 220pF
VOUT_LCL
DIFFVOUT
VOSNS+
VOSNS–
fSET
60.4k + R
SET
N
RSET
N = NUMBER OF PHASES
VOUT = 0.6V
C3
22µF
6.3V
C4
470µF
6.3V
VOUT
3.3V
20A
+
REFER TO
TABLE 2
RSET
6.65k
100pF
MARGIN CONTROL
CLOCK SYNC
180° PHASE
TRACK/SS CONTROL
C7
0.033µF
VIN
PGOOD
PGOOD
MPGM
RUN
COMP
INTVCC
DRVCC
C8
10µF
35V
×2
PLLIN TRACK/SS
VOUT
LTM4601HV
392k
SGND
PGND
C3
22µF
6.3V
VFB
MARG0
MARG1
+
C4
470µF
6.3V
REFER TO
TABLE 2
VOUT_LCL
DIFFVOUT
VOSNS+
VOSNS–
fSET
4601HV F21
*C5 OPTIONAL TO REDUCE ANY LC RINGING.
NOT NEEDED FOR LOW INDUCTANCE PLANE CONNECTION
Figure 21. 2-Phase Parallel, 3.3V at 20A Design
4601hvfb
23
LTM4601HV
TYPICAL APPLICATIONS
LTC6908-1
2-PHASE
OSCILLATOR
C8
0.1µF
R1
118k
V+
OUT1
GND
OUT2
SET
MOD
3.3V
VIN
6V TO 28V
C1
10µF
35V
R3
100k
R4
100k
VIN
0° PHASE
180° PHASE
PLLIN
VOUT
PGOOD
VFB
RUN
VOUT_LCL
COMP
DIFFVOUT
INTVCC
LTM4601HV
DRVCC
VOSNS+
MPGM
VOSNS–
MARG0
fSET
TRACK/SS
MARG1
R2
392k
C3
0.15µF
3.3V
SGND
R1
13.3k
C2
100µF
6.3V
VOUT1
3.3V
C4 10A
150µF
6.3V
3.3V
TRACK
MARGIN CONTROL
R7
100k
R8
100k
C5
10µF
35V
R16
60.4k
R6
392k
R15
19.1k
PGND
VIN
PLLIN
VOUT
PGOOD
VFB
RUN
VOUT_LCL
COMP
DIFFVOUT
INTVCC
LTM4601HV
DRVCC
VOSNS+
MPGM
VOSNS–
MARG0
fSET
TRACK/SS
MARG1
SGND
R5
19.1k
C6
100µF
6.3V
VOUT2
2.5V
C7 10A
150µF
6.3V
MARGIN CONTROL
PGND
4601HV F22
Figure 22. Dual Outputs (3.3V and 2.5V) with Coincident Tracking
LTC6908-1
2-PHASE
OSCILLATOR
C8
0.1µF
R1
182k
V+
OUT1
GND
OUT2
SET
MOD
3.3V
VIN
6V TO 28V
C1
10µF
35V
R3
100k
R4
100k
VIN
0° PHASE
180° PHASE
PLLIN
VOUT
PGOOD
VFB
RUN
VOUT_LCL
COMP
DIFFVOUT
INTVCC
LTM4601HV
DRVCC
VOSNS+
MPGM
VOSNS–
MARG0
fSET
TRACK/SS
MARG1
R2
392k
C3
0.15µF
SGND
PGND
3.3V
C8
47pF
R1
30.1k
MARGIN CONTROL
C2
100µF
6.3V
VOUT1
1.8V
C4 10A
220µF
6.3V
3.3V
TRACK
R16
60.4k
R15
40.2k
R7
100k
R8
100k
C5
10µF
35V
R6
392k
VIN
PLLIN
VOUT
PGOOD
VFB
RUN
VOUT_LCL
COMP
DIFFVOUT
INTVCC
LTM4601HV
DRVCC
VOSNS+
MPGM
VOSNS–
MARG0
fSET
TRACK/SS
MARG1
SGND
C9
47pF
R5
40.2k
C6
100µF
6.3V
VOUT2
1.5V
C7 10A
220µF
6.3V
MARGIN CONTROL
PGND
4601HV F23
Figure 23. Dual Outputs (1.8V and 1.5V) with Coincident Tracking
24
4601hvfb
aaa Z
0.630 ±0.025 Ø 118x
3.1750
3.1750
SUGGESTED PCB LAYOUT
TOP VIEW
1.9050
PACKAGE TOP VIEW
E
0.6350
0.0000
0.6350
4
1.9050
PIN “A1”
CORNER
6.9850
5.7150
4.4450
4.4450
5.7150
6.9850
Y
6.9850
5.7150
4.4450
3.1750
1.9050
0.6350
0.0000
0.6350
1.9050
3.1750
4.4450
5.7150
6.9850
X
D
2.45 – 2.55
aaa Z
SYMBOL
A
A1
A2
b
b1
D
E
e
F
G
aaa
bbb
ccc
ddd
eee
NOM
3.42
0.60
2.82
0.75
0.63
15.0
15.0
1.27
13.97
13.97
DIMENSIONS
0.15
0.10
0.20
0.30
0.15
MAX
3.62
0.70
2.92
0.90
0.66
NOTES
DETAIL B
PACKAGE SIDE VIEW
A2
TOTAL NUMBER OF BALLS: 118
MIN
3.22
0.50
2.72
0.60
0.60
DETAIL A
b1
0.27 – 0.37
SUBSTRATE
A1
ddd M Z X Y
eee M Z
DETAIL B
MOLD
CAP
ccc Z
Øb (118 PLACES)
// bbb Z
A
(Reference LTC DWG # 05-08-1903 Rev A)
BGA Package
118-Lead (15mm × 15mm × 3.42mm)
Z
e
b
L
K
J
G
G
F
e
E
PACKAGE BOTTOM VIEW
H
D
C
B
A
DETAILS OF PIN #1 IDENTIFIER ARE OPTIONAL,
BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
THE PIN #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE
BALL DESIGNATION PER JESD MS-028 AND JEP95
TRAY PIN 1
BEVEL
BGA 118 0112 REV A
PACKAGE IN TRAY LOADING ORIENTATION
LTMXXXXXX
µModule
6. SOLDER BALL COMPOSITION IS 96.5% Sn/3.0% Ag/0.5% Cu
5. PRIMARY DATUM -Z- IS SEATING PLANE
4
3
2. ALL DIMENSIONS ARE IN MILLIMETERS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994
COMPONENT
PIN “A1”
3
SEE NOTES
F
b
M
DETAIL A
1
2
3
4
5
6
7
8
9
10
11
12
PIN 1
LTM4601HV
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
25
4601hvfb
aaa Z
0.630 ±0.025 Ø 118x
E
PACKAGE TOP VIEW
3.1750
3.1750
SUGGESTED PCB LAYOUT
TOP VIEW
1.9050
4
0.6350
0.0000
0.6350
PIN “A1”
CORNER
1.9050
Y
6.9850
5.7150
4.4450
3.1750
1.9050
0.6350
0.0000
0.6350
1.9050
3.1750
4.4450
5.7150
6.9850
X
D
aaa Z
0.27
2.45
MIN
2.72
0.60
NOM
2.82
0.63
15.00
15.00
1.27
13.97
13.97
0.32
2.50
DIMENSIONS
0.37
2.55
0.15
0.10
0.05
MAX
2.92
0.66
NOTES
DETAIL B
PACKAGE SIDE VIEW
TOTAL NUMBER OF LGA PADS: 118
SYMBOL
A
b
D
E
e
F
G
H1
H2
aaa
bbb
eee
H1
SUBSTRATE
eee S X Y
DETAIL A
0.630 ±0.025 SQ. 118x
DETAIL B
H2
MOLD
CAP
A
(Reference LTC DWG # 05-08-1801 Rev A)
bbb Z
26
Z
LGA Package
118-Lead (15mm × 15mm × 2.82mm)
e
b
L
K
J
G
G
F
e
E
PACKAGE BOTTOM VIEW
H
D
C
B
A
DETAILS OF PIN #1 IDENTIFIER ARE OPTIONAL,
BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
THE PIN #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE
BALL DESIGNATION PER JESD MS-028 AND JEP95
TRAY PIN 1
BEVEL
LGA 118 1011 REV A
PACKAGE IN TRAY LOADING ORIENTATION
LTMXXXXXX
µModule
5. PRIMARY DATUM -Z- IS SEATING PLANE
4
3
2. ALL DIMENSIONS ARE IN MILLIMETERS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994
COMPONENT
PIN “A1”
3
SEE NOTES
F
b
M
DETAIL A
1
2
3
4
5
6
7
8
9
C(0.30)
PAD 1
10
11
12
LTM4601HV
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
4601hvfb
6.9850
5.7150
4.4450
4.4450
5.7150
6.9850
LTM4601HV
PACKAGE DESCRIPTION
Table 5. Pin Assignment (Arranged by Pin Number)
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
A1
VIN
B1
VIN
C1
VIN
D1
PGND
E1
PGND
F1
PGND
A2
VIN
B2
VIN
C2
VIN
D2
PGND
E2
PGND
F2
PGND
A3
VIN
B3
VIN
C3
VIN
D3
PGND
E3
PGND
F3
PGND
A4
VIN
B4
VIN
C4
VIN
D4
PGND
E4
PGND
F4
PGND
A5
VIN
B5
VIN
C5
VIN
D5
PGND
E5
PGND
F5
PGND
A6
VIN
B6
VIN
C6
VIN
D6
PGND
E6
PGND
F6
PGND
A7
INTVCC
B7
–
C7
–
D7
–
E7
PGND
F7
PGND
A8
PLLIN
B8
–
C8
–
D8
–
E8
–
F8
PGND
A9
TRACK/SS
B9
–
C9
–
D9
–
E9
–
F9
PGND
A10
RUN
B10
–
C10
–
D10
–
E10
–
F10
–
A11
COMP
B11
–
C11
–
D11
–
E11
–
F11
–
A12
MPGM
B12
fSET
C12
MARG0
D12
MARG1
E12
DRVCC
F12
VFB
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
G1
PGND
H1
PGND
J1
VOUT
K1
VOUT
L1
VOUT
M1
VOUT
G2
PGND
H2
PGND
J2
VOUT
K2
VOUT
L2
VOUT
M2
VOUT
G3
PGND
H3
PGND
J3
VOUT
K3
VOUT
L3
VOUT
M3
VOUT
G4
PGND
H4
PGND
J4
VOUT
K4
VOUT
L4
VOUT
M4
VOUT
G5
PGND
H5
PGND
J5
VOUT
K5
VOUT
L5
VOUT
M5
VOUT
G6
PGND
H6
PGND
J6
VOUT
K6
VOUT
L6
VOUT
M6
VOUT
G7
PGND
H7
PGND
J7
VOUT
K7
VOUT
L7
VOUT
M7
VOUT
G8
PGND
H8
PGND
J8
VOUT
K8
VOUT
L8
VOUT
M8
VOUT
G9
PGND
H9
PGND
J9
VOUT
K9
VOUT
L9
VOUT
M9
VOUT
G10
–
H10
–
J10
VOUT
K10
VOUT
L10
VOUT
M10
VOUT
G11
–
H11
–
J11
–
K11
VOUT
L11
VOUT
M11
VOUT
G12
PGOOD
H12
SGND
J12
VOSNS+
K12
DIFFVOUT
L12
VOUT_LCL
M12
VOSNS–
4601hvfb
27
LTM4601HV
PACKAGE DESCRIPTION
Table 6. Pin Assignment (Arranged by Pin Function)
PIN NAME
PIN NAME
A1
A2
A3
A4
A5
A6
VIN
VIN
VIN
VIN
VIN
VIN
D1
D2
D3
D4
D5
D6
PGND
PGND
PGND
PGND
PGND
PGND
B1
B2
B3
B4
B5
B6
VIN
VIN
VIN
VIN
VIN
VIN
C1
C2
C3
C4
C5
C6
VIN
VIN
VIN
VIN
VIN
VIN
E1
E2
E3
E4
E5
E6
E7
PGND
PGND
PGND
PGND
PGND
PGND
PGND
F1
F2
F3
F4
F5
F6
F7
F8
F9
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
G1
G2
G3
G4
G5
G6
G7
G8
G9
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
H1
H2
H3
H4
H5
H6
H7
H8
H9
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
28
PIN NAME
PIN NAME
J1
J2
J3
J4
J5
J6
J7
J8
J9
J10
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
A7
A8
A9
A10
A11
A12
INTVCC
PLLIN
TRACK/SS
RUN
COMP
MPGM
B12
fSET
C12
MARG0
K1
K2
K3
K4
K5
K6
K7
K8
K9
K10
K11
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
D12
MARG1
E12
DRVCC
F12
VFB
G12
PGOOD
H12
SGND
J12
VOSNS+
K12
DIFFVOUT
L12
VOUT_LCL
L1
L2
L3
L4
L5
L6
L7
L8
L9
L10
L11
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
M12
VOSNS–
M1
M2
M3
M4
M5
M6
M7
M8
M9
M10
M11
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
PIN NAME
B7
B8
B9
B10
B11
-
C7
C8
C9
C10
C11
-
D7
D8
D9
D10
D11
-
E8
E9
E10
E11
-
F10
F11
-
G10
G11
-
H10
H11
-
J11
-
4601hvfb
LTM4601HV
REVISION HISTORY
(Revision history begins at Rev B)
REV
DATE
DESCRIPTION
PAGE NUMBER
B
03/12
Revised entire data sheet to include the BGA package.
1–30
4601hvfb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
29
LTM4601HV
PACKAGE PHOTOS
2.82mm
15mm
3.42mm
15mm
15mm
15mm
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTM4628
26V, Dual 8A, DC/DC Step-Down μModule
Regulator
4.5V ≤ VIN ≤ 26.5V, 0.6V ≤ VOUT ≤ 5V, Remote Sense Amplifier, Internal Temperature
Sensing Output, 15mm × 15mm × 4.32mm LGA
LTM4627
20V, 15A DC/DC Step-Down μModule
Regulator
4.5V ≤ VIN ≤ 20V, 0.6V ≤ VOUT ≤ 5V, PLL Input, VOUT Tracking, Remote Sense Amplifier,
15mm × 15mm × 4.32mm LGA
LTM4611
1.5VIN(MIN), 15A DC/DC Step-Down μModule
Regulator
1.5V ≤ VIN ≤ 5.5V, 0.8V ≤ VOUT ≤ 5V, PLL Input, Remote Sense Amplifier, VOUT Tracking,
15mm × 15mm × 4.32mm LGA
LTM4613
8A EN55022 Class B DC/DC Step-Down
μModule Regulator
5V ≤ VIN ≤ 36V, 3.3V ≤ VOUT ≤ 15V, PLL Input, VOUT Tracking and Margining,
15mm × 15mm × 4.32mm LGA
LTM4601AHV
28V, 12A DC/DC Step-Down μModule
Regulator
4.5V ≤ VIN ≤ 28V, 0.6V ≤ VOUT ≤ 5V, PLL Input, Remote Sense Amplifier, VOUT Tracking
and Margining, 15mm × 15mm × 2.82mm LGA or 15mm × 15mm × 3.42mm BGA
LTM4601A
20V, 12A DC/DC Step-Down μModule
Regulator
4.5V ≤ VIN ≤ 20V, 0.6V ≤ VOUT ≤ 5V, PLL Input, Remote Sense Amplifier, VOUT Tracking
and Margining, 15mm × 15mm × 2.82mm LGA or 15mm × 15mm × 3.42mm BGA
LTM8027
60V, 4A DC/DC Step-Down μModule
Regulator
4.5V ≤ VIN ≤ 60V, 2.5V ≤ VOUT ≤ 24V, CLK Input, 15mm × 15mm × 4.32mm LGA
LTM8032
36V, 2A EN55022 Class B DC/DC Step-Down
μModule Regulator
3.6V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 10V, Synchronizable, 9mm × 15mm × 2.82mm LGA
or 9mm × 15mm × 3.42mm BGA
LTM8061
32V, 2A Step-Down μModule Battery Charger
with Programmable Input Current Limit
Compatible with Single Cell or Dual Cell Li-Ion or Li-Poly Battery Stacks (4.1V, 4.2V,
8.2V, or 8.4V), 4.95V ≤ VIN ≤ 32V, C/10 or Adjustable Timer Charge Termination,
NTC Resistor Monitor Input, 9mm × 15mm × 4.32mm LGA
This product contains technology licensed from Silicon Semiconductor Corporation.
30
Linear Technology Corporation
®
4601hvfb
LT 0312 REV B • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 l FAX: (408) 434-0507
l
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2007