LTM4601AHV 12A, 28VIN DC/DC µModule with PLL, Output Tracking and Margining DESCRIPTION FEATURES n n n n n n n n n n n n n n n n n n Complete Switch Mode Power Supply Wide Input Voltage Range: 4.5V to 28V 12A DC Typical, 14A Peak Output Current 0.6V to 5V Output Voltage Output Voltage Tracking and Margining Redundant Mounting Pads for Enhanced SolderJoint Strength Parallel Multiple μModulesTM for Current Sharing Differential Remote Sensing for Precision Regulation PLL Frequency Synchronization ±1.5% Total DC Error Current Foldback Protection (Disabled at Start-Up) Pb-Free (e4) RoHS Compliant Package with Gold Finish Pads –55°C to 125°C Operating Temperature Range (LTM4601AHVMPV) Ultrafast™ Transient Response Up to 95% Efficiency at 5VIN, 3.3VOUT Programmable Soft-Start Output Overvoltage Protection Enhanced (15mm × 15mm × 2.8mm) Surface Mount LGA Package APPLICATIONS n n The LTM®4601AHV is a complete 12A step-down switch mode DC/DC power supply with onboard switching controller, MOSFETs, inductor and all support components. The μModule is housed in a small surface mount 15mm × 15mm × 2.8mm LGA package. The LTM4601AHV LGA package is designed with redundant mounting pads to enhance solder-joint strength for extended temperature cycling endurance. Operating over an input voltage range of 4.5 to 28V, the LTM4601AHV supports an output voltage range of 0.6V to 5V as well as output voltage tracking and margining. The high efficiency design delivers 12A continuous current (14A peak). Only bulk input and output capacitors are needed to complete the design. The low profile (2.8mm) and light weight (1.7g) package easily mounts in unused space on the back side of PC boards for high density point of load regulation. The μModule can be synchronized with an external clock for reducing undesirable frequency harmonics and allows PolyPhase® operation for high load currents. An onboard differential remote sense amplifier can be used to accurately regulate an output voltage independent of load current. L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. PolyPhase is a registered trademark of Linear Technology Corporation. μModule and Ultrafast are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 5481178, 5847554, 6580258, 6304066, 6476589, 6774611, 6677210. Telecom, Industrial and Networking Equipment Military and Avionics Systems TYPICAL APPLICATION Efficiency and Power Loss vs Load Current 2.5V/12A Power Supply with 4.5V to 28V Input 95 CLOCK SYNC TRACK/SS CONTROL ON/OFF CIN R1 392k 5% MARGIN RUN COMP INTVCC DRVCC MPGM PLLIN TRACK/SS VOUT LTM4601AHV SGND PGND VFB MARG0 MARG1 5 85 VOUT 2.5V 12A 100pF MARGIN CONTROL COUT VOUT_LCL DIFFVOUT VOSNS+ VOSNS– fSET 12VIN 24VIN 80 4 75 POWER LOSS 70 3 24VIN 65 12VIN 60 2 55 POWER LOSS (W) VIN PGOOD 6 EFFICIENCY 90 EFFICIENCY (%) VIN 4.5V TO 28V 1 50 RSET 19.1k 4601AHV TA01a 45 0 2 8 6 4 10 LOAD CURRENT (A) 12 14 0 4601AHV TA01b 4601ahvf 1 LTM4601AHV ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION INTVCC, DRVCC, VOUT_LCL, VOUT (VOUT ≤ 3.3V with Remote Sense Amp) .................................... –0.3V to 6V PLLIN, TRACK/SS, MPGM, MARG0, MARG1, PGOOD, fSET .............................. –0.3V to INTVCC + 0.3V RUN ............................................................. –0.3V to 5V VFB, COMP ................................................ –0.3V to 2.7V VIN ............................................................. –0.3V to 28V VOSNS+, VOSNS– .......................... –0.3V to INTVCC + 0.3V Operating Temperature Range (Note 2) E and I Grades ..................................... –40°C to 85°C MP Grade........................................... –55°C to 125°C Junction Temperature ........................................... 125°C Storage Temperature Range................... –55°C to 125°C INTVCC PLLIN TRACK/SS RUN COMP MPGM (Note 1) TOP VIEW VIN MTP1 INTVCC MTP2 MTP3 PGND fSET MARG0 MARG1 DRVCC VFB PGOOD SGND VOSNS+ DIFFVOUT VOUT_LCL VOSNS– VOUT LGA PACKAGE 133-LEAD (15mm s 15mm s 2.8mm) TJMAX = 125°C, θJA = 15°C/W, θJC = 6°C/W, θJA DERIVED FROM 95mm × 76mm PCB WITH 4 LAYERS WEIGHT = 1.7g ORDER INFORMATION LEAD FREE FINISH PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTM4601AHVEV#PBF LTM4601AHVV 133-Lead (15mm × 15mm × 2.8mm) LGA –40°C to 85°C LTM4601AHVIV#PBF LTM4601AHVV 133-Lead (15mm × 15mm × 2.8mm) LGA –40°C to 85°C LTM4601AHVMPV#PBF LTM4601AHVMPV 133-Lead (15mm × 15mm × 2.8mm) LGA –55°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/ ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C, VIN = 12V. Per typical application (front page) configuration, RSET = 40.2k. SYMBOL PARAMETER CONDITIONS VIN(DC) Input DC Voltage VOUT(DC) Output Voltage Total Variation with Line and Load CIN = 10μF ×3, COUT = 200μF, RSET = 40.2k VIN = 5V to 28V, IOUT = 0A to 12A (Note 5) VIN(UVLO) Undervoltage Lockout Threshold IINRUSH(VIN) Input Inrush Current at Startup MIN l 4.5 l 1.478 TYP MAX UNITS 28 V 1.5 1.522 V IOUT = 0A 3.2 4 V IOUT = 0A. VOUT = 1.5V VIN = 5V VIN = 12V 0.6 0.7 A A VIN = 12V, VOUT = 1.5V, No Switching VIN = 12V, VOUT = 1.5V, Switching Continuous VIN = 5V, VOUT = 1.5V, No Switching VIN = 5V, VOUT = 1.5V, Switching Continuous Shutdown, RUN = 0, VIN = 12V 3.8 38 2.5 42 22 mA mA mA mA μA Input Specifications IQ(VIN,NO LOAD) Input Supply Bias Current 4601ahvf 2 LTM4601AHV ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C, VIN = 12V. Per typical application (front page) configuration, RSET = 40.2k. SYMBOL PARAMETER CONDITIONS IS(VIN) Input Supply Current VIN = 12V, VOUT = 1.5V, IOUT = 12A VIN = 12V, VOUT = 3.3V, IOUT = 12A VIN = 5V, VOUT = 1.5V, IOUT = 12A INTVCC VIN = 12V, RUN > 2V No Load MIN TYP MAX 1.81 3.63 4.29 4.7 5 UNITS A A A 5.3 V Output Specifications IOUTDC Output Continuous Current Range VIN = 12V, VOUT = 1.5V (Note 5) 12 A ΔVOUT(LINE) VOUT Line Regulation Accuracy VOUT = 1.5V, IOUT = 0A, VIN = 4.5V – 28V l 0 0.3 % ΔVOUT(LOAD) VOUT Load Regulation Accuracy VOUT = 1.5V, IOUT = 0A to 12A, VIN = 12V, with Remote Sense Amplifier, (Note 5) l 0.25 % VOUT(AC) Output Ripple Voltage IOUT = 0A, COUT = 2×, 100μF/X5R/Ceramic VIN = 12V, VOUT = 1.5V VIN = 5V, VOUT = 1.5V 20 18 mVP-P mVP-P fS Output Ripple Voltage Frequency IOUT = 5A, VIN = 12V, VOUT = 1.5V 850 kHz ΔVOUT(START) Turn-On Overshoot, TRACK/SS = 10nF COUT = 200μF, VOUT = 1.5V, IOUT = 0A VIN = 12V VIN = 5V 20 20 mV mV tSTART Turn-On Time, TRACK/SS = Open COUT = 200μF, VOUT = 1.5V, IOUT = 1A Resistive Load VIN = 12V VIN = 5V 0.5 0.7 ms ms Load: 0% to 50% to 0% of Full Load, COUT = 2 × 22μF/Ceramic, 470μF, 4V Sanyo POSCAP VIN = 12V VIN = 5V 35 35 mV mV 25 μs 17 17 A A ΔVOUTLS Peak Deviation for Dynamic Load tSETTLE Settling Time for Dynamic Load Step Load: 0% to 50%, or 50% to 0% of Full Load VIN = 12V IOUTPK Output Current Limit COUT = 200μF, Table 2 VIN = 12V, VOUT = 1.5V VIN = 5V, VOUT = 1.5V Remote Sense Amp (Note 3) VOSNS+, VOSNS– CM Range Common Mode Input Voltage Range VIN = 12V, RUN > 2V 0 INTVCC – 1 DIFFVOUT Range Output Voltage Range 0 INTVCC VOS Input Offset Voltage Magnitude AV Differential Gain 1 V/V GBP Gain Bandwidth Product 3 MHz SR Slew Rate RIN Input Resistance CMRR Common Mode Rejection Mode VIN = 12V, DIFF OUT Load = 100k 1.25 2 l VOSNS+ to GND V V mV mV 2 V/μs 20 kΩ 100 dB 4601ahvf 3 LTM4601AHV ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C, VIN = 12V. Per typical application (front page) configuration, RSET = 40.2k. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VFB Error Amplifier Input Voltage Accuracy IOUT = 0A, VOUT = 1.5V 0.594 0.6 0.606 V VRUN RUN Pin On/Off Threshold 1 1.5 1.9 V ISS/TRACK Soft-Start Charging Current VSS/TRACK = 0V –1.0 –1.5 –2.0 μA tON(MIN) Minimum On Time tOFF(MIN) Minimum Off Time (Note 4) 50 100 ns (Note 4) 250 400 ns RPLLIN PLLIN Input Resistance IDRVCC Current into DRVCC Pin RFBHI Resistor Between VOUT and VFB VMPGM Margin Reference Voltage 1.18 V VMARG0, VMARG1 MARG0, MARG1 Voltage Thresholds 1.4 V Control Stage l 50 VOUT = 1.5V, IOUT = 1A, Frequency = 850kHz, DRVCC = 5V 60.098 kΩ 18 25 mA 60.4 60.702 kΩ PGOOD Output ΔVFBH PGOOD Upper Threshold VFB Rising 7 10 13 % ΔVFBL PGOOD Lower Threshold VFB Falling –7 –10 –13 % ΔVFB(HYS) PGOOD Hysteresis VFB Returning 1.5 VPGL PGOOD Low Voltage IPGOOD = 5mA 0.15 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTM4601AHVE is guaranteed to meet performance specifications from 0°C to 85°C. Specifications over the –40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls. The LTM4601AHVI is % 0.4 V guaranteed and tested over the –40°C to 85°C temperature range. The LTM4601AHVMP is guaranteed and tested over the –55°C to 125°C temperature range. For output current derating at high temperature, please refer to Thermal Considerations and Output Current Derating discussion. Note 3: Remote sense amplifier recommended for ≤3.3V output. Note 4: 100% tested at wafer level only. Note 5: See output current derating curves for different VIN, VOUT and TA. 4601ahvf 4 LTM4601AHV TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Load Current with 5VIN 100 EFFICIENCY (%) 90 85 80 75 0.6VOUT 1.2VOUT 1.5VOUT 2.5VOUT 3.3VOUT 70 65 95 95 90 90 85 85 80 EFFICIENCY (%) 95 EFFICIENCY (%) Efficiency vs Load Current with 24VIN Efficiency vs Load Current with 12VIN 100 60 (See Figures 19 and 20 for all curves) 80 75 70 0.6VOUT 1.2VOUT 1.5VOUT 2.5VOUT 3.3VOUT 5VOUT 65 60 55 5 10 0 15 LOAD CURRENT (A) 10 5 LOAD CURRENT (A) 70 65 60 1.5VOUT 2.5VOUT 3.3VOUT 5.0VOUT 55 50 50 0 75 45 15 4601AHV G02 4601AHV G01 1.2V Transient Response 1.5V Transient Response 1.8V Transient Response VOUT 50mV/DIV VOUT 50mV/DIV IOUT 5A/DIV IOUT 5A/DIV IOUT 5A/DIV 20μs/DIV 1.5V AT 6A/μs LOAD STEP COUT = 3x 22μF 6.3V CERAMICS 470μF 4V SANYO POSCAP C3 = 100pF 4601AHV G04 2.5V Transient Response 15 4601AHV G03 VOUT 50mV/DIV 20μs/DIV 1.2V AT 6A/μs LOAD STEP COUT = 3x 22μF 6.3V CERAMICS 470μF 4V SANYO POSCAP C3 = 100pF 10 5 LOAD CURRENT (A) 0 4601AHV G05 20μs/DIV 1.8V AT 6A/μs LOAD STEP COUT = 3x 22μF 6.3V CERAMICS 470μF 4V SANYO POSCAP C3 = 100pF 3.3V Transient Response 4601AHV G06 VFB vs Temperature 0.606 VOUT 50mV/DIV IOUT 5A/DIV IOUT 5A/DIV 20μs/DIV 2.5V AT 6A/μs LOAD STEP COUT = 3x 22μF 6.3V CERAMICS 470μF 4V SANYO POSCAP C3 = 100pF 4601AHV G07 0.604 0.602 VFB (V) VOUT 50mV/DIV 20μs/DIV 3.3V AT 6A/μs LOAD STEP COUT = 3x 22μF 6.3V CERAMICS 470μF 4V SANYO POSCAP C3 = 100pF 4601AHV G08 0.600 0.598 0.596 0.594 –55 –25 35 65 5 TEMPERATURE (°C) 95 125 4601AHV G15 4601ahvf 5 LTM4601AHV TYPICAL PERFORMANCE CHARACTERISTICS (See Figures 19 and 20 for all curves) Start-Up, TA = –55°C Start-Up, IOUT = 12A (Resistive Load) Start-Up, IOUT = 0A VOUT 0.5V/DIV VOUT 0.5V/DIV NO LOAD 10A LOAD IIN 1A/DIV IIN 0.5A/DIV 10ms/DIV VIN = 12V VOUT = 1.5V COUT = 470μF, 3x 22μF SOFT-START = 10nF 4601AHV G16 5ms/DIV VIN = 12V VOUT = 1.5V COUT = 470μF, 3x 22μF SOFT-START = 10nF 4601AHV G09 VIN to VOUT Step-Down Ratio 3.3V OUTPUT WITH 130k FROM VOUT TO fSET 5.0 4.5 OUTPUT VOLTAGE (V) 4601AHV G10 Track, IOUT = 12A 5.5 TRACK/SS 0.5V/DIV VFB 0.5V/DIV 5V OUTPUT WITH 100k RESISTOR ADDED FROM fSET TO GND 4.0 3.5 3.0 VOUT 1V/DIV 2.0 5V OUTPUT WITH NO RESISTOR ADDED FROM fSET TO GND 1.5 2.5V OUTPUT 1.0 1.8V OUTPUT 0.5 1.5V OUTPUT 2.5 0 2ms/DIV VIN = 12V VOUT = 1.5V COUT = 470μF, 3x 22MF SOFT-START = 10nF 2ms/DIV VIN = 12V VOUT = 1.5V COUT = 470μF, 3x 22μF SOFT-START = 10nF 4601AHV G12 1.2V OUTPUT 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 INPUT VOLTAGE (V) 4601AHV G11 Short-Circuit Protection, IOUT = 0A Short-Circuit Protection, IOUT = 12A VOUT 0.5V/DIV VOUT 0.5V/DIV IIN 1A/DIV IIN 1A/DIV 50μs/DIV VIN = 12V VOUT = 1.5V COUT = 470μF, 3x 22μF SOFT-START = 10nF 4601AHV G13 50μs/DIV VIN = 12V VOUT = 1.5V COUT = 470μF 3x 22μF SOFT-START = 10nF 4601AHV G14 4601ahvf 6 LTM4601AHV PIN FUNCTIONS (See Package Description for Pin Assignment) VIN (Bank 1): Power Input Pins. Apply input voltage between these pins and PGND pins. Recommend placing input decoupling capacitance directly between VIN pins and PGND pins. PLLIN (Pin A8): External Clock Synchronization Input to the Phase Detector. This pin is internally terminated to SGND with a 50k resistor. Apply a clock above 2V and below INTVCC. See Applications Information. VOUT (Bank 3): Power Output Pins. Apply output load between these pins and PGND pins. Recommend placing output decoupling capacitance directly between these pins and PGND pins. Review the figure below. TRACK/SS (Pin A9): Output Voltage Tracking and Soft- Start Pin. When the module is configured as a master output, then a soft-start capacitor is placed on this pin to ground to control the master ramp rate. A soft-start capacitor can be used for soft-start turn on as a stand alone regulator. Slave operation is performed by putting a resistor divider from the master output to the ground, and connecting the center point of the divider to this pin. See Applications Information. PGND (Bank 2): Power ground pins for both input and output returns. VOSNS– (Pin M12): (–) Input to the Remote Sense Amplifier. This pin connects to the ground remote sense point. The remote sense amplifier is used for VOUT ≤3.3V. VOSNS+ (Pin J12): (+) Input to the Remote Sense Amplifier. This pin connects to the output remote sense point. The remote sense amplifier is used for VOUT ≤3.3V. DIFFVOUT (Pin K12): Output of the Remote Sense Amplifier. This pin connects to the VOUT_LCL pin. DRVCC (Pin E12): This pin normally connects to INTVCC for powering the internal MOSFET drivers. This pin can be biased up to 6V from an external supply with about 50mA capability, or an external circuit shown in Figure 18. This improves efficiency at the higher input voltages by reducing power dissipation in the module. INTVCC PLLIN TRACK/SS RUN COMP MPGM INTVCC (Pin A7, D9): This pin is for additional decoupling of the 5V internal regulator. These pins are internally connected. Pin A7 is a test pin. TOP VIEW VIN BANK 1 PGND BANK 2 VOUT BANK 3 A B C D E F G H J K L M MTP1 INTVCC MTP2 MTP3 fSET MARG0 MARG1 DRVCC VFB PGOOD SGND VOSNS+ DIFFVOUT VOUT_LCL VOSNS– 1 2 3 4 5 6 7 8 9 10 11 12 MPGM (Pins A12, B11): Programmable Margining Input. A resistor from this pin to ground sets a current that is equal to 1.18V/R. This current multiplied by 10kΩ will equal a value in millivolts that is a percentage of the 0.6V reference voltage. See Applications Information. To parallel LTM4601AHVs, each requires an individual MPGM resistor. Do not tie MPGM pins together. Both pins are internally connected. Pin A12 is a test pin. fSET (Pins B12, C11): Frequency Set Internally to 850kHz. An external resistor can be placed from this pin to ground to increase frequency. This pin can be decoupled with a 1000pF capacitor. See Applications Information for frequency adjustment. Both pins are internally connected. Pin B12 is a test pin. VFB (Pin F12): The Negative Input of the Error Amplifier. Internally, this pin is connected to VOUT_LCL pin with a 60.4k precision resistor. Different output voltages can be programmed with an additional resistor between VFB and SGND pins. See Applications Information. MARG0 (Pin C12): This pin is the LSB logic input for the margining function. Together with the MARG1 pin will determine if margin high, margin low or no margin state is applied. The pin has an internal pull-down resistor of 50k. See Applications Information. MARG1 (Pin D12): This pin is the MSB logic input for the margining function. Together with the MARG0 pin will determine if margin high, margin low or no margin state is applied. The pin has an internal pull-down resistor of 50k. See Applications Information. 4601ahvf 7 LTM4601AHV PIN FUNCTIONS (See Package Description for Pin Assignment) SGND (Pins H12, H11, G11): Signal Ground. These pins connect to PGND at output capacitor point. See Figure 17. RUN (Pin A10): Run Control Pin. A voltage above 1.9V will turn on the module, and when below 1V, will turn off the module. A programmable UVLO function can be accomplished with a resistor from VIN to this pin that has a 5.1V zener to ground. Maximum pin voltage is 5V. Limit current into the RUN pin to less than 1mA. COMP (Pin A11): Current Control Threshold and Error Amplifier Compensation Point. The current comparator threshold increases with this control voltage. The voltage ranges from 0V to 2.4V with 0.7V corresponding to zero sense voltage (zero current). VOUT_LCL (Pin L12): VOUT connects directly to this pin to bypass the remote sense amplifier, or DIFFVOUT connects to this pin when remote sense amplifier is used. PGOOD (Pins G12, F11): Output Voltage Power Good Indicator. Open-drain logic output that is pulled to ground when the output voltage is not within ±10% of the regulation point, after a 25μs power bad mask timer expires. MTP1, MTP2, MPT3 (Pins C10, D10, D11 ): Extra Mounting Pads with No Internal Connection. These pads are used for increased solder integrity strength. SIMPLIFIED BLOCK DIAGRAM VOUT_LCL >2V = ON <0.9V = OFF MAX = 5V VOUT 1M RUN PGOOD 5.1V ZENER COMP 1.5μF VIN 4.5V TO 28V + CIN 60.4k INTERNAL COMP POWER CONTROL SGND Q1 VOUT 2.5V 12A MARG1 MARG0 22μF VFB RSET 19.1k 50k 50k + fSET COUT Q2 39.2k PGND MPGM 10k INTVCC TRACK/SS PLLIN 4.7μF 50k + – CSS VOSNS– 10k 10k VOSNS+ 10k INTVCC DIFFVOUT DRVCC 4601AHV F01 Figure 1. Simplified LTM4601AHV Block Diagram 4601ahvf 8 LTM4601AHV DECOUPLING REQUIREMENTS TA = 25°C, VIN = 12V. Use Figure 1 configuration. SYMBOL PARAMETER CONDITIONS MIN TYP CIN External Input Capacitor Requirement (VIN = 4.5V to 28V, VOUT = 2.5V) COUT External Output Capacitor Requirement (VIN = 4.5V to 28V, VOUT = 2.5V) MAX UNITS IOUT = 12A, 3× 10μF Ceramics 20 30 μF IOUT = 12A 100 200 μF OPERATION Power Module Description The LTM4601AHV is a standalone nonisolated switching mode DC/DC power supply. It can deliver up to 12A of DC output current with some external input and output capacitors. This module provides precisely regulated output voltage programmable via one external resistor from 0.6VDC to 5.0VDC over a 4.5V to 28V wide input voltage. The typical application schematics are shown in Figures 19 and 20. The LTM4601AHV has an integrated constant on-time current mode regulator, ultralow RDS(ON) FETs with fast switching speed and integrated Schottky diodes. The typical switching frequency is 850kHz at full load. With current mode control and internal feedback loop compensation, the LTM4601AHV module has sufficient stability margins and good transient performance under a wide range of operating conditions and with a wide range of output capacitors, even all ceramic output capacitors. Current mode control provides cycle-by-cycle fast current limit. Besides, foldback current limiting is provided in an overcurrent condition while VFB drops. Internal overvoltage and undervoltage comparators pull the open-drain PGOOD output low if the output feedback voltage exits a ±10% window around the regulation point. Furthermore, in an overvoltage condition, internal top FET Q1 is turned off and bottom FET Q2 is turned on and held on until the overvoltage condition clears. Pulling the RUN pin below 1V forces the controller into its shutdown state, turning off both Q1 and Q2. At low load current, the module works in continuous current mode by default to achieve minimum output voltage ripple. When DRVCC pin is connected to INTVCC an integrated 5V linear regulator powers the internal gate drivers. If a 5V external bias supply is applied on the DRVCC pin, then an efficiency improvement will occur due to the reduced power loss in the internal linear regulator. This is especially true at the higher input voltage range. The LTM4601AHV has a very accurate differential remote sense amplifier with very low offset. This provides for very accurate remote sense voltage measurement. The MPGM pin, MARG0 pin and MARG1 pin are used to support voltage margining, where the percentage of margin is programmed by the MPGM pin, and the MARG0 and MARG1 select margining. The PLLIN pin provides frequency synchronization of the device to an external clock. The TRACK/SS pin is used for power supply tracking and soft-start programming. 4601ahvf 9 LTM4601AHV APPLICATIONS INFORMATION The typical LTM4601AHV application circuits are shown in Figures 19 and 20. External component selection is primarily determined by the maximum load current and output voltage. Refer to Table 2 for specific external capacitor requirements for a particular application. VIN to VOUT Step-Down Ratios There are restrictions in the maximum VIN and VOUT step down ratio that can be achieved for a given input voltage. These constraints are shown in the Typical Performance Characteristics curves labeled “VIN to VOUT Step-Down Ratio”. Note that additional thermal derating may apply. See the Thermal Considerations and Output Current Derating section of this data sheet. The MPGM pin programs a current that when multiplied by an internal 10k resistor sets up the 0.6V reference ± offset for margining. A 1.18V reference divided by the RPGM resistor on the MPGM pin programs the current. Calculate VOUT(MARGIN): VOUT(MARGIN) = %VOUT • VOUT 100 where %VOUT is the percentage of VOUT you want to margin, and VOUT(MARGIN) is the margin quantity in volts: RPGM = VOUT 1.18 V • • 10k 0.6 V VOUT(MARGIN) where RPGM is the resistor value to place on the MPGM pin to ground. Output Voltage Programming and Margining The PWM controller has an internal 0.6V reference voltage. As shown in the Block Diagram, a 1M and a 60.4k 0.5% internal feedback resistor connects VOUT and VFB pins together. The VOUT_LCL pin is connected between the 1M and the 60.4k resistor. The 1M resistor is used to protect against an output overvoltage condition if the VOUT_LCL pin is not connected to the output, or if the remote sense amplifier output is not connected to VOUT_LCL. The output voltage will default to 0.6V. Adding a resistor RSET from the VFB pin to SGND pin programs the output voltage: 60.4k + RSET VOUT = 0.6 V RSET Table 1. Standard 1% Resistor Values RSET (kΩ) Open 60.4 40.2 30.1 25.5 19.1 13.3 8.25 VOUT (V) 0.6 1.2 1.5 1.8 2 2.5 3.3 5 The output margining will be ± margining of the value. This is controlled by the MARG0 and MARG1 pins. See the truth table below: MARG1 MARG0 MODE LOW LOW NO MARGIN LOW HIGH MARGIN UP HIGH LOW MARGIN DOWN HIGH HIGH NO MARGIN Input Capacitors LTM4601AHV module should be connected to a low AC impedance DC source. Input capacitors are required to be placed adjacent to the module. In Figure 18, the 10μF ceramic input capacitors are selected for their ability to handle the large RMS current into the converter. An input bulk capacitor of 100μF is optional. This 100μF capacitor is only needed if the input source impedance is compromised by long inductive leads or traces. 4601ahvf 10 LTM4601AHV APPLICATIONS INFORMATION D= VOUT VIN Without considering the inductor current ripple, the RMS current of the input capacitor can be estimated as: ICIN(RMS) = IOUT(MAX ) η% • D • ( 1– D ) In the above equation, η% is the estimated efficiency of the power module. CIN can be a switcher-rated electrolytic aluminum capacitor, OS-CON capacitor or high volume ceramic capacitor. Note the capacitor ripple current ratings are often based on temperature and hours of life. This makes it advisable to properly derate the input capacitor, or choose a capacitor rated at a higher temperature than required. Always contact the capacitor manufacturer for derating requirements. In Figures 19 and 20, the 10μF ceramic capacitors are together used as a high frequency input decoupling capacitor. In a typical 12A output application, three very low ESR, X5R or X7R (extended temperature range), 10μF ceramic capacitors are recommended. These decoupling capacitors should be placed directly adjacent to the module input pins in the PCB layout to minimize the trace inductance and high frequency AC noise. Each 10μF ceramic is typically good for 2A to 3A of RMS ripple current. Refer to your ceramics capacitor catalog for the RMS current ratings. Multiphase operation with multiple LTM4601AHV devices in parallel will lower the effective input RMS ripple current due to the interleaving operation of the regulators. Application Note 77 provides a detailed explanation. Refer to Figure 2 for the input capacitor ripple current requirement as a function of the number of phases. The figure provides a ratio of RMS ripple current to DC load current as function of duty cycle and the number of paralleled phases. Pick the corresponding duty cycle and the number of phases to arrive at the correct ripple current value. For example, the 2-phase parallel LTM4601AHV design provides 24A at 2.5V output from a 12V input. The duty cycle is DC = 2.5V/12V = 0.21. The 2-phase curve has a ratio of ~0.25 for a duty cycle of 0.21. This 0.25 ratio of RMS ripple current to a DC load current of 24A equals ~6A of input RMS ripple current for the external input capacitors. Output Capacitors The LTM4601AHV is designed for low output voltage ripple. The bulk output capacitors defined as COUT are chosen with low enough effective series resistance (ESR) to meet the output voltage ripple and transient requirements. COUT can be a low ESR tantalum capacitor, a low ESR polymer capacitor or a ceramic capacitor. The typical capacitance is 200μF if all ceramic output capacitors are used. Additional output filtering may be required by the system designer, if further reduction of output ripple or dynamic transient spike is required. Table 2 shows a matrix of different output voltages and output capacitors to minimize the voltage droop and overshoot during a 5A/μs transient. The table optimizes total equivalent ESR and total bulk capacitance to maximize transient performance. 0.6 RMS INPUT RIPPLE CURRENT DC LOAD CURRENT For a buck converter, the switching duty-cycle can be estimated as: 0.5 1-PHASE 2-PHASE 3-PHASE 4-PHASE 6-PHASE 12-PHASE 0.4 0.3 0.2 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 DUTY FACTOR (VOUT/VIN) 0.8 0.9 4601AHV F02 Figure 2. Normalized Input RMS Ripple Current vs Duty Factor for One to Six Modules (Phases) 4601ahvf 11 LTM4601AHV APPLICATIONS INFORMATION Multiphase operation with multiple LTM4601AHV devices in parallel will lower the effective output ripple current due to the interleaving operation of the regulators. For example, each LTM4601AHV’s inductor current of a 12V to 2.5V multiphase design can be read from the Inductor Ripple Current versus Duty Cycle graph (Figure 3). The large ripple current at low duty cycle and high output voltage 12 2.5V OUTPUT 10 5V OUTPUT 1.8V OUTPUT IL (A) 8 1.5V OUTPUT 1.2V OUTPUT 6 3.3V OUTPUT WITH 130k ADDED FROM VOUT TO fSET 4 5V OUTPUT WITH 100k ADDED FROM fSET TO GND 2 0 0 20 40 60 DUTY CYCLE (VOUT/VIN) 80 4601AHV F03 Figure 3. Inductor Ripple Current vs Duty Cycle can be reduced by adding an external resistor from fSET to ground which increases the frequency. If the duty cycle is DC = 2.5V/12V = 0.21, the inductor ripple current for 2.5V output at 21% duty cycle is ~6A in Figure 3. Figure 4 provides a ratio of peak-to-peak output ripple current to the inductor current as a function of duty cycle and the number of paralleled phases. Pick the corresponding duty cycle and the number of phases to arrive at the correct output ripple current ratio value. If a 2-phase operation is chosen at a duty cycle of 21%, then 0.6 is the ratio. This 0.6 ratio of output ripple current to inductor ripple of 6A equals 3.6A of effective output ripple current. Refer to Application Note 77 for a detailed explanation of output ripple current reduction as a function of paralleled phases. The output voltage ripple has two components that are related to the amount of bulk capacitance and effective series resistance (ESR) of the output bulk capacitance. Therefore, the output voltage ripple can be calculated with the known effective output ripple current. The equation: ΔVOUT(P-P) ≈ (ΔIL/(8 • f • m • COUT) + ESR • ΔIL), where 1.00 0.95 1-PHASE 2-PHASE 3-PHASE 4-PHASE 6-PHASE 0.90 0.85 RATIO = PEAK-TO-PEAK OUTPUT RIPPLE CURRENT DIr 0.80 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 DUTY CYCLE (VO/VIN) 4601AHV F04 Figure 4. Normalized Output Ripple Current vs Duty Cycle, Dlr = VOT/LI, Dlr = Each Phase’s Inductor Current 4601ahvf 12 LTM4601AHV APPLICATIONS INFORMATION f is frequency and m is the number of parallel phases. This calculation process can be easily fulfilled using our Excel tool (Refer to the Linear Technology μModule Power Design Tool). Fault Conditions: Current Limit and Overcurrent Foldback LTM4601AHV has a current mode controller, which inherently limits the cycle-by-cycle inductor current not only in steady-state operation, but also in transient. To further limit current in the event of an overload condition, the LTM4601AHV provides foldback current limiting. If the output voltage falls by more than 50%, then the maximum output current is progressively lowered to about one sixth of its full current limit value. down with another regulator. The master regulator’s output is divided down with an external resistor divider that is the same as the slave regulator’s feedback divider. Figure 5 shows an example of coincident tracking. Ratiometric modes of tracking can be achieved by selecting different resistor values to change the output tracking ratio. The master output must be greater than the slave output for the tracking to work. Figure 6 shows the coincident output tracking characteristics. MASTER OUTPUT TRACK CONTROL VIN 100k MPGM RUN COMP INTVCC DRVCC Soft-Start and Tracking The TRACK/SS pin provides a means to either soft-start the regulator or track it to a different power supply. A capacitor on this pin will program the ramp rate of the output voltage. A 1.5μA current source will charge up the external soft-start capacitor to 80% of the 0.6V internal voltage reference minus any margin delta. This will control the ramp of the internal reference and the output voltage. The total soft-start time can be calculated as: ( ) t SOFTSTART = 0.8 • 0.6 V – VOUT(MARGIN) • VIN PGOOD CIN PLLIN TRACK/SS VOUT LTM4601AHV SGND PGND 60.4k FROM VOUT TO VFB INTERNAL R2 60.4k R1 40.2k SLAVE OUTPUT VFB MARG0 MARG1 COUT VOUT_LCL DIFFVOUT VOSNS+ VOSNS– fSET RSET 40.2k 4601AHV F05 Figure 5 CSS 1.5µA When the RUN pin falls below 1.5V, then the SS pin is reset to allow for proper soft-start control when the regulator is enabled again. Current foldback and force continuous mode are disabled during the soft-start process. The soft-start function can also be used to control the output ramp up time, so that another regulator can be easily tracked to it. Output Voltage Tracking Output voltage tracking can be programmed externally using the TRACK/SS pin. The output can be tracked up and MASTER OUTPUT SLAVE OUTPUT OUTPUT VOLTAGE TIME 4601AHV F06 Figure 6 4601ahvf 13 LTM4601AHV APPLICATIONS INFORMATION Run Enable The RUN pin is used to enable the power module. The pin has an internal 5.1V zener to ground. The pin can be driven with a logic input not to exceed 5V. The RUN pin can also be used as an undervoltage lock out (UVLO) function by connecting a resistor divider from the input supply to the RUN pin: VUVLO = R1+ R2 • 1.5V R2 through the LDO is about 20mA. The internal LDO power dissipation can be calculated as: PLDO_LOSS = 20mA • (VIN – 5V) The LTM4601AHV also provides the external gate driver voltage pin DRVCC. If there is a 5V rail in the system, it is recommended to connect DRVCC pin to the external 5V rail. This is especially true for higher input voltages. Do not apply more than 6V to the DRVCC pin. A 5V output can be used to power the DRVCC pin with an external circuit as shown in Figure 18. Power Good Parallel Operation of the Module The PGOOD pin is an open-drain pin that can be used to monitor valid output voltage regulation. This pin monitors a ±10% window around the regulation point and tracks with margining. The LTM4601AHV device is an inherently current mode controlled device. Parallel modules will have very good current sharing. This will balance the thermals on the design. Figure 21 shows a schematic of the parallel design. The voltage feedback equation changes with the variable n as modules are paralleled: COMP Pin This pin is the external compensation pin. The module has already been internally compensated for most output voltages. Table 2 is provided for most application requirements. A spice model will be provided for other control loop optimization. PLLIN The power module has a phase-locked loop comprised of an internal voltage controlled oscillator and a phase detector. This allows the internal top MOSFET turn-on to be locked to the rising edge of the external clock. The frequency range is ±30% around the operating frequency of 850kHz. A pulse detection circuit is used to detect a clock on the PLLIN pin to turn on the phase lock loop. The pulse width of the clock has to be at least 400ns and 2V in amplitude. During the start-up of the regulator, the phase-lock loop function is disabled. INTVCC and DRVCC Connection An internal low dropout regulator produces an internal 5V supply that powers the control circuitry and DRVCC for driving the internal power MOSFETs. Therefore, if the system does not have a 5V power rail, the LTM4601AHV can be directly powered by VIN. The gate driver current 60.4k + RFB VOUT = 0.6 V N RFB N is the number of paralleled modules. Figure 21 shows two LTM4601AHV modules used in a parallel design. An LTM4601AHV device can be used without the diff amp. Thermal Considerations and Output Current Derating The power loss curves in Figures 7 and 8 can be used in coordination with the load current derating curves in Figures 9 to 16 for calculating an approximate θJA for the module with various heat sinking methods. Thermal models are derived from several temperature measurements at the bench and thermal modeling analysis. Thermal Application Note 103 provides a detailed explanation of the analysis for the thermal models and the derating curves. Tables 3 and 4 provide a summary of the equivalent θJA for the noted conditions. These equivalent θJA parameters are correlated to the measured values, and are improved with air flow. The case temperature is maintained at 100°C or below for the derating curves. The maximum case temperature of 100°C is to allow for a rise of about 13°C 4601ahvf 14 LTM4601AHV APPLICATIONS INFORMATION 6 5.0 4.5 5 3.5 POWER LOSS (W) POWER LOSS (W) 4.0 24V LOSS 3.0 12V LOSS 2.5 2.0 1.5 4 24V LOSS 3 12V LOSS 2 5V LOSS 1.0 1 0.5 0 0 0 2 6 8 4 OUTPUT CURRENT (A) 10 12 0 2 4 6 8 OUTPUT CURRENT (A) 10 4601AHV F08 4601AHV F07 Figure 8. 24VIN and 3.3V Power Loss 12 12 10 10 MAXIMUM LOAD CURRENT (A) MAXIMUM LOAD CURRENT (A) Figure 7. 24VIN and 1.5V Power Loss 8 6 4 5VIN, 1.5VOUT 0LFM 5VIN, 1.5VOUT 200LFM 5VIN, 1.5VOUT 400LFM 2 0 50 8 6 4 5VIN, 1.5VOUT 0LFM 5VIN, 1.5VOUT 200LFM 5VIN, 1.5VOUT 400LFM 2 0 100 60 70 80 90 AMBIENT TEMPERATURE (°C) 50 4601AHV F10 Figure 10. BGA Heat Sink 5VIN 12 12 10 10 MAXIMUM LOAD CURRENT (A) MAXIMUM LOAD CURRENT (A) Figure 9. No Heat Sink 5VIN 8 6 4 12VIN, 1.5VOUT 0LFM 12VIN, 1.5VOUT 200LFM 12VIN, 1.5VOUT 400LFM 0 50 8 6 4 12VIN, 1.5VOUT 0LFM 12VIN, 1.5VOUT 200LFM 12VIN, 1.5VOUT 400LFM 2 0 100 60 70 80 90 AMBIENT TEMPERATURE (°C) 4601AHV F11 Figure 11. No Heat Sink 12VIN 100 60 70 80 90 AMBIENT TEMPERATURE (°C) 4601AHV F09 2 12 50 100 60 70 80 90 AMBIENT TEMPERATURE (°C) 4601AHV F12 Figure 12. BGA Heat Sink 12VIN 4601ahvf 15 LTM4601AHV 12 12 10 10 MAXIMUM LOAD CURRENT (A) MAXIMUM LOAD CURRENT (A) APPLICATIONS INFORMATION 8 6 4 12VIN, 3.3VOUT 0LFM 12VIN, 3.3VOUT 200LFM 12VIN, 3.3VOUT 400LFM 2 0 40 60 80 AMBIENT TEMPERATURE (°C) 8 6 4 12VIN, 3.3VOUT 0LFM 12VIN, 3.3VOUT 200LFM 12VIN, 3.3VOUT 400LFM 2 0 100 40 60 80 AMBIENT TEMPERATURE (°C) 4601AHV F13 4601AHV F14 Figure 14. 12VIN, 3.3VOUT, BGA Heat Sink 12 12 10 10 MAXIMUM LOAD CURRENT (A) MAXIMUM LOAD CURRENT (A) Figure 13. 12VIN, 3.3VOUT, No Heat Sink 8 6 4 24VIN, 1.5VOUT 0LFM 24VIN, 1.5VOUT 200LFM 24VIN, 1.5VOUT 400LFM 2 0 40 60 80 AMBIENT TEMPERATURE (°C) 8 6 4 24VIN, 1.5VOUT 0LFM 24VIN, 1.5VOUT 200LFM 24VIN, 1.5VOUT 400LFM 2 0 100 4601AHV F15 Figure 15. 24VIN, 1.5VOUT, No Heat Sink 100 40 60 80 AMBIENT TEMPERATURE (°C) 100 4601AHV F16 Figure 16. 24VIN, 1.5VOUT, BGA Heat Sink 4601ahvf 16 LTM4601AHV APPLICATIONS INFORMATION Table 2. Output Voltage Response Versus Component Matrix* (Refer to Figures 19 and 20), 0A to 6A Load Step TYPICAL MEASURED VALUES COUT1 VENDORS TDK TAIYO YUDEN TAIYO YUDEN VOUT (V) 1.2 1.2 1.2 CIN (CERAMIC) PART NUMBER C4532X5R0J107MZ (100μF,6.3V) JMK432BJ107MU-T ( 100μF, 6.3V) JMK316BJ226ML-T501 ( 22μF, 6.3V) 2 × 10μF 35V CIN (BULK) 150μF 35V COUT1 (CERAMIC) 3 × 22μF 6.3V COUT2 (BULK) 470μF 4V CCOMP NONE C3 47pF VIN (V) 5 DROOP (mV) 70 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 470μF 2.5V NONE 100pF 5 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 330μF 6.3V NONE 22pF 5 NONE NONE 100pF 470μF 4V 470μF 2.5V 330μF 6.3V NONE 470μF 4V 470μF 2.5V 330μF 6.3V NONE 470μF 4V 470μF 2.5V 330μF 6.3V NONE 470μF 4V 470μF 2.5V 330μF 6.3V NONE 470μF 4V 470μF 2.5V 330μF 6.3V NONE 470μF 4V 330μF 6.3V 470μF 4V NONE 470μF 4V 470μF 4V 330μF 6.3V NONE 330μF 6.3V 470μF 4V 470μF 4V NONE 470μF 4V 470μF 4V 330μF 6.3V NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE 100pF 100pF 22pF 100pF 100pF 33pF 100pF 100pF 100pF 33pF 100pF 100pF 47pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 100pF 220pF NONE 100pF 100pF NONE 220pF 220pF 100pF 100pF 100pF 100pF 100pF 150pF 100pF 100pF 22pF 22pF 150μF 35V 4 × 100μF 6.3V 2 × 10μF 35V 1.2 2 × 10μF 35V 150μF 35V 3 × 22μF 6.3V 1.2 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 1.2 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 1.2 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 1.5 2 × 10μF 35V 150μF 35V 3 × 22μF 6.3V 1.5 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 1.5 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 1.5 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 1.5 2 × 10μF 35V 150μF 35V 3 × 22μF 6.3V 1.5 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 1.5 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 1.5 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 1.8 2 × 10μF 35V 150μF 35V 3 × 22μF 6.3V 1.8 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 1.8 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 1.8 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 1.8 2 × 10μF 35V 150μF 35V 3 × 22μF 6.3V 1.8 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 1.8 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 1.8 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 2.5 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 2.5 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 2.5 2 × 10μF 35V 150μF 35V 3 × 22μF 6.3V 2.5 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 2.5 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 2.5 2 × 10μF 35V 150μF 35V 3 × 22μF 6.3V 2.5 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 2.5 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 3.3 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 3.3 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 3.3 2 × 10μF 35V 150μF 35V 3 × 22μF 6.3V 3.3 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 3.3 2 × 10μF 35V 150μF 35V 1 × 100μF 6.3V 3.3 2 × 10μF 35V 150μF 35V 3 × 22μF 6.3V 3.3 2 × 10μF 35V 150μF 35V 2 × 100μF 6.3V 3.3 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 5 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V 5 2 × 10μF 35V 150μF 35V 4 × 100μF 6.3V *X7R is recommended for extended temperature range 1.2 COUT2 VENDORS SANYO POSCAP SANYO POSCAP SANYO POSCAP PART NUMBER 6TPE330MIL (330μF, 6.3V) 2R5TPE470M9 (470μF, 2.5V) 4TPE470MCL (470μF, 4V) PEAK TO PEAK (mV) 140 RECOVERY TIME (μs) 30 LOAD STEP (A/μs) 6 RSET (kΩ) 60.4 35 70 20 6 60.4 70 140 20 6 60.4 5 40 93 30 6 60.4 12 12 12 12 5 5 5 5 12 12 12 12 5 5 5 5 12 12 12 12 5 5 5 5 12 12 12 12 7 7 7 7 12 12 12 12 15 20 70 35 70 49 48 54 44 61 48 54 44 54 48 44 68 65 60 60 68 65 48 56 57 60 48 51 56 70 120 110 110 114 110 110 110 114 188 159 140 70 140 98 100 109 84 118 100 109 89 108 100 90 140 130 120 120 140 130 103 113 116 115 103 102 113 140 240 214 214 230 214 214 214 230 375 320 30 20 20 20 35 30 30 30 35 30 25 25 30 20 30 30 30 30 30 20 30 30 30 25 30 30 30 25 30 30 30 30 30 35 35 30 25 25 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 60.4 60.4 60.4 60.4 40.2 40.2 40.2 40.2 40.2 40.2 40.2 40.2 30.1 30.1 30.1 30.1 30.1 30.1 30.1 30.1 19.1 19.1 19.1 19.1 19.1 19.1 19.1 19.1 13.3 13.3 13.3 13.3 13.3 13.3 13.3 13.3 8.25 8.25 4601ahvf 17 LTM4601AHV APPLICATIONS INFORMATION Table 3. 1.5V Output at 12A DERATING CURVE VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK θJA (°C/W) Figures 9, 11, 15 5, 12, 24 Figure 7 0 None 15.2 Figures 9, 11, 15 5, 12, 24 Figure 7 200 None 14 Figures 9, 11, 15 5, 12, 24 Figure 7 400 None 12 Figures 10, 12, 16 5, 12, 24 Figure 7 0 BGA Heat Sink 13.9 Figures 10, 12, 16 5, 12, 24 Figure 7 200 BGA Heat Sink 11.3 Figures 10, 12, 16 5, 12, 24 Figure 7 400 BGA Heat Sink 10.25 DERATING CURVE VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK θJA (°C/W) Figure 13 12 Figure 8 0 None 15.2 Figure 13 12 Figure 8 200 None 14.6 Figure 13 12 Figure 8 400 None 13.4 Figure 14 12 Figure 8 0 BGA Heat Sink 13.9 Figure 14 12 Figure 8 200 BGA Heat Sink 11.1 Figure 14 12 Figure 8 400 BGA Heat Sink 10.5 Table 4. 3.3V Output at 12A Heat Sink Manufacturer Wakefield Engineering Part No: 20069 Phone: 603-635-2800 4601ahvf 18 LTM4601AHV APPLICATIONS INFORMATION to 25°C inside the μModule with a thermal resistance θJC from junction to case between 6°C/W to 9°C/W. This will maintain the maximum junction temperature inside the μModule below 125°C. • Place high frequency ceramic input and output capacitors next to the VIN, PGND and VOUT pins to minimize high frequency noise. • Place a dedicated power ground layer underneath the unit. Refer frequency synchronization source to power ground. Safety Considerations The LTM4601AHV modules do not provide isolation from VIN to VOUT. There is no internal fuse. If required, a slow blow fuse with a rating twice the maximum input current needs to be provided to protect each unit from catastrophic failure. • To minimize the via conduction loss and reduce module thermal stress, use multiple vias for interconnection between top layer and other power layers. • Do not put vias directly on pads unless they are capped. Layout Checklist/Example • Use a separated SGND ground copper area for components connected to signal pins. Connect the SGND to PGND underneath the unit. The high integration of LTM4601AHV makes the PCB board layout very simple and easy. However, to optimize its electrical and thermal performance, some layout considerations are still necessary. Figure 17 gives a good example of the recommended layout. • Use large PCB copper areas for high current path, including VIN, PGND and VOUT. It helps to minimize the PCB conduction loss and thermal stress. VIN CIN CIN ••• ••• CONTROL • • • • • • • • • • • • • • • • • • • • •••• •••• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •••• •••• • COUT COUT • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • PGND • • • • • • CONTROL • • • SIGNAL GND • • • • • • • • CONTROL VOUT 4601AHV F17 Figure 17. Recommended Layout 4601ahvf 19 LTM4601AHV APPLICATIONS INFORMATION Frequency Adjustment LTM4601AHV minimum off-time = 400ns; the 14A peak specified value. A 100k resistor is placed from fSET to ground, and the parallel combination of 100k and 39.2k equates to 28k. The IfSET calculation with 28k and 28V input voltage equals 333μA. This equates to a tON of 144ns. This will increase the switching frequency from ~884kHz to ~1.24MHz for the 28V to 5V conversion. The minimum on time is above 100ns at 28V input. Since the switching frequency is approximately constant over input and output conditions, then the lower input voltage range is limited to 10V for the 1.24MHz operation due to the 400ns minimum off time. Equation: tON = (VOUT/VIN) • (1/Frequency) equates to a 400ns on time, and a 400ns off time. The “VIN to VOUT Step-Down Ratio” curves reflect an operating range of 10V to 28V for 1.24MHz operation with a 100k resistor to ground as shown in Figure 18, and an 8V to 16V operation for fSET floating. These modifications are made to provide wider input voltage ranges for the 5V output designs while limiting the inductor ripple current, and maintaining the 400ns minimum off time. tOFF = t – tON, where t = 1/Frequency Example for 3.3V Output The LTM4601AHV is designed to typically operate at 850kHz across most input conditions. The fSET pin is normally left open or decoupled with an optional 1000pF capacitor. The switching frequency has been optimized for maintaining constant output ripple noise over most operating ranges. The 850kHz switching frequency and the 400ns minimum off time can limit operation at higher duty cycles like 5V to 3.3V, and produce excessive inductor ripple currents for lower duty cycle applications like 28V to 5V. The 5V and 3.3V drop out curves are modified by adding an external resistor on the fSET pin to allow for lower input voltage operation, or higher input voltage operation. Example for 5V Output LTM4601AHV minimum on-time = 100ns; tON = ((4.8 • 10pf)/IfSET) Duty Cycle = tON/t or VOUT/VIN Equations for setting frequency: IfSET = (VIN/(3 • RfSET)), for 28V operation, IfSET = 238μA, tON = ((4.8 • 10pF)/IfSET), tON = 202ns, where the internal RfSET is 39.2k. Frequency = (VOUT/(VIN • tON)) = (5V/(28 • 202ns)) ~ 884kHz. The inductor ripple current begins to get high at the higher input voltages due to a larger voltage across the inductor. This is noted in the Typical Inductor Ripple Current verses Duty Cycle graph (Figure 3) where IL ≈ 10A at 20% duty cycle. The inductor ripple current can be lowered at the higher input voltages by adding an external resistor from fSET to ground to increase the switching frequency. A 7A ripple current is chosen, and the total peak current is equal to 1/2 of the 7A ripple current plus the output current. The 5V output current is limited to 8A, so the total peak current is less than 11.5A. This is below LTM4601AHV minimum on-time = 100ns; tON = ((3.3 • 10pF)/IfSET) LTM4601AHV minimum off-time = 400ns; tOFF = t – tON, where t = 1/Frequency Duty Cycle (DC) = tON/t or VOUT/VIN Equations for setting frequency: IfSET = (VIN/(3 • RfSET)), for 28V operation, IfSET = 238μA, tON = ((3.3 • 10pf)/IfSET), tON = 138.7ns, where the internal RfSET is 39.2k. Frequency = (VOUT/(VIN • tON)) = (3.3V/(28 • 138.7ns)) ~ 850kHz. The minimum on-time and minimumoff time are within specification at 139ns and 1037ns. The 4.5V minimum input for converting 3.3V output will not meet the minimum off-time specification of 400ns. tON = 868ns, Frequency = 850kHz, tOFF = 315ns. 4601ahvf 20 LTM4601AHV APPLICATIONS INFORMATION Solution Lower the switching frequency at lower input voltages to allow for higher duty cycles, and meet the 400ns minimum off-time at 4.5V input voltage. The off-time should be about 500ns with 100ns guard band. The duty cycle for (3.3V/4.5) = ~73%. Frequency = (1 – DC)/tOFF or (1 – 0.73)/500ns = 540kHz. The switching frequency needs to be lowered to 540kHz at 4.5V input. tON = DC/ frequency, or 1.35μs. The fSET pin voltage compliance is 1/3 of VIN, and the IfSET current equates to 38μA with the internal 39.2k. The IfSET current needs to be 24μA for 540kHz operation. As shown in Figure 19, a resistor can be placed from VOUT to fSET to lower the effective IfSET current out of the fSET pin to 24μA. The fSET pin is 4.5V/3 =1.5V and VOUT = 3.3V, therefore 130k will source 14μA into the fSET node and lower the IfSET current to 24μA. This enables the 540kHz operation and the 4.5V to 28V input operation for down converting to 3.3V output. The frequency will scale from 540kHz to 1.1 MHz over this input range. This provides for an effective output current of 8A over the input range. VOUT VIN 10V TO 28V R2 100k TRACK/SS CONTROL R4 100k MPGM RUN COMP INTVCC DRVCC 5% MARGIN C2 10μF 35V VIN PGOOD R1 392k 1% C1 10μF 35V PLLIN TRACK/SS VOUT LTM4601AHV SGND PGND REVIEW TEMPERATURE DERATING CURVE + VFB MARG0 MARG1 VOUT_LCL DIFFVOUT VOSNS+ VOSNS– C3 100μF 6.3V SANYO POSCAP VOUT 5V 8A 22μF 6.3V REFER TO TABLE 2 fSET RfSET 100k RSET 8.25k MARGIN CONTROL IMPROVE EFFICIENCY FOR ≥12V INPUT SOT-323 CMSSH-3C3 4601AHV F18 Figure 18. 5V at 8A Design Without Differential Amplifier 4601ahvf 21 LTM4601AHV APPLICATIONS INFORMATION VOUT VIN 4.5V TO 16V R2 100k R4 100k PGOOD C2 10μF 25V 3x TRACK/SS CONTROL PLLIN TRACK/SS VOUT VIN PGOOD MPGM RUN COMP INTVCC DRVCC LTM4601AHV R1 392k SGND REVIEW TEMPERATURE DERATING CURVE VFB MARG0 MARG1 RfSET 130k fSET PGND 5% MARGIN MARGIN CONTROL 22μF 6.3V C3 100μF 6.3V SANYO POSCAP + VOUT_LCL DIFFVOUT VOSNS+ VOSNS– VOUT 3.3V 10A RSET 13.3k 4601AHV F19 Figure 19. 3.3V at 10A Design CLOCK SYNC C5 0.01μF VOUT VIN 22V TO 28V R2 100k R4 100k PGOOD CIN BULK OPT + CIN 10μF 35V 3x CER MPGM RUN ON/OFF COMP INTVCC DRVCC R1 392k 5% MARGIN PLLIN TRACK/SS VOUT VIN PGOOD LTM4601AHV SGND PGND VFB MARG0 MARG1 REVIEW TEMPERATURE DERATING CURVE C3 100pF COUT1 100μF 6.3V MARGIN CONTROL VOUT_LCL DIFFVOUT VOSNS+ VOSNS– fSET RfSET 175k VIN 4601AHV F20 RSET 40.2k + COUT2 470μF 6.3V VOUT 1.5V 10A REFER TO TABLE 2 FOR DIFFERENT OUTPUT VOLTAGE Figure 20. Typical 22V to 28V, 1.5V at 10A Design, 500kHz 4601ahvf 22 LTM4601AHV APPLICATIONS INFORMATION VOUT CLOCK SYNC 0° PHASE VIN 6V TO 28V + C1 0.1μF 118k 1% R2 100k LTC6908-1 1 2 3 V+ OUT1 GND OUT2 SET MOD 6 5 4 C5* 100μF 35V C2 10μF 35V 2x R4 100k MPGM RUN COMP INTVCC DRVCC R1 392k PLLIN TRACK/SS VOUT VIN PGOOD LTM4601AHV SGND 5% MARGIN 2-PHASE OSCILLATOR C6 220pF VFB MARG0 MARG1 VOUT_LCL DIFFVOUT VOSNS+ VOSNS– fSET PGND TRACK/SS CONTROL 60.4k + R SET N VOUT = 0.6V RSET N = NUMBER OF PHASES C3 22μF 6.3V C4 470μF 6.3V VOUT 3.3V 20A + REFER TO TABLE 2 RSET 6.65k 100pF MARGIN CONTROL CLOCK SYNC 180° PHASE TRACK/SS CONTROL C7 0.033μF VIN PGOOD PGOOD MPGM RUN COMP INTVCC DRVCC C8 10μF 35V 2x PLLIN TRACK/SS VOUT LTM4601AHV 392k SGND PGND C3 22μF 6.3V VFB MARG0 MARG1 + C4 470μF 6.3V REFER TO TABLE 2 VOUT_LCL DIFFVOUT VOSNS+ VOSNS– fSET 4601AHV F21 *C5 OPTIONAL TO REDUCE ANY LC RINGING. NOT NEEDED FOR LOW INDUCTANCE PLANE CONNECTION Figure 21. 2-Phase Parallel, 3.3V at 20A Design 4601ahvf 23 LTM4601AHV TYPICAL APPLICATIONS LTC6908-1 2-PHASE OSCILLATOR C8 0.1μF R1 118k 0° PHASE V+ OUT1 GND OUT2 SET MOD 3.3V VIN 6V TO 28V R3 100k R4 100k VIN 180° PHASE PLLIN VOUT PGOOD FB RUN VOUT_LCL COMP DIFFVOUT INTVCC LTM4601AHV DRVCC VOSNS+ MPGM VOSNS– MARG0 fSET TRACK/SS MARG1 C1 10μF 35V R2 392k C3 0.15μF 3.3V SGND R1 13.3k C2 100μF 6.3V VOUT1 3.3V C4 10A 150μF 6.3V 3.3V R7 100k R8 100k C5 10μF 35V TRACK R16 60.4k MARGIN CONTROL R6 392k R15 19.1k PGND VIN PLLIN VOUT PGOOD FB RUN VOUT_LCL COMP DIFFVOUT INTVCC LTM4601AHV DRVCC VOSNS+ MPGM VOSNS– MARG0 fSET TRACK/SS MARG1 SGND R5 19.1k C6 100μF 6.3V VOUT2 2.5V C7 10A 150μF 6.3V MARGIN CONTROL PGND 4601AHV F22 Figure 22. Dual Outputs (3.3V and 2.5V) with Tracking LTC6908-1 2-PHASE OSCILLATOR C8 0.1μF R1 182k OUT1 GND OUT2 SET MOD 1.8V VIN 6V TO 28V R3 100k R4 100k 0° PHASE V+ VIN 180° PHASE PLLIN VOUT PGOOD FB RUN VOUT_LCL COMP DIFFVOUT INTVCC LTM4601AHV DRVCC VOSNS+ MPGM VOSNS– MARG0 fSET TRACK/SS MARG1 C1 10μF 35V R2 392k C3 0.15μF SGND PGND 1.8V C8 47pF R1 30.1k MARGIN CONTROL C2 100μF 6.3V VOUT1 1.8V C4 10A 220μF 6.3V 3.3V TRACK R16 60.4k R15 40.2k R7 100k R8 100k C5 10μF 35V R6 392k VIN PLLIN VOUT PGOOD FB RUN VOUT_LCL COMP DIFFVOUT INTVCC LTM4601AHV DRVCC VOSNS+ MPGM VOSNS– MARG0 fSET TRACK/SS MARG1 SGND C9 47pF R5 40.2k C6 100μF 6.3V VOUT2 1.5V C7 10A 220μF 6.3V MARGIN CONTROL PGND 4601AHV F23 Figure 23. Dual Outputs (1.8V and 1.5V) with Tracking 4601ahvf 24 6.9850 5.7150 4.4450 3.1750 1.9050 0.6350 0.0000 0.6350 1.9050 3.1750 4.4450 5.7150 6.9850 PACKAGE TOP VIEW 3.1750 3.1750 SUGGESTED PCB LAYOUT TOP VIEW 1.9050 4 0.6350 0.0000 0.6350 PAD 1 CORNER 15 BSC 1.9050 aaa Z 6.9850 5.7150 4.4450 4.4450 5.7150 6.9850 X 15 BSC Y bbb Z DETAIL B 2.72 – 2.92 DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE LAND DESIGNATION PER JESD MO-222, SPP-010 SYMBOL TOLERANCE 0.10 aaa 0.10 bbb 0.05 eee 6. THE TOTAL NUMBER OF PADS: 133 5. PRIMARY DATUM -Z- IS SEATING PLANE 4 3 2. ALL DIMENSIONS ARE IN MILLIMETERS 3 M L TRAY PIN 1 BEVEL COMPONENT PIN “A1” PADS SEE NOTES 1.27 BSC 13.97 BSC 0.12 – 0.28 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 DETAIL A 0.27 – 0.37 SUBSTRATE eee S X Y DETAIL B 0.630 ±0.025 SQ. 133x aaa Z 2.45 – 2.55 MOLD CAP Z (Reference LTC DWG # 05-08-1755 Rev Ø) LGA Package 133-Lead (15mm × 5mm × 2.82mm) K G F E LTMXXXXXX μModule PACKAGE BOTTOM VIEW H D C B LGA 133 0807 REV Ø A DETAIL A PACKAGE IN TRAY LOADING ORIENTATION J 13.97 BSC 1 2 3 4 5 6 7 8 9 10 11 12 C(0.30) PAD 1 LTM4601AHV PACKAGE DESCRIPTION 4601ahvf 25 LTM4601AHV PACKAGE DESCRIPTION Pin Assignment Table 5 (Arranged by Pin Number) PIN NAME A1 VIN A2 VIN A3 VIN A4 VIN A5 VIN A6 VIN A7 INTVCC A8 PLLIN A9 TRACK/SS A10 RUN A11 COMP A12 MPGM PIN NAME B1 VIN B2 VIN B3 VIN B4 VIN B5 VIN B6 VIN B7 PGND B8 B9 PGND B10 B11 MPGM B12 fSET PIN NAME C1 VIN C2 VIN C3 VIN C4 VIN C5 VIN C6 VIN C7 PGND C8 C9 PGND C10 MTP1 C11 fSET C12 MARG0 PIN NAME D1 PGND D2 PGND D3 PGND D4 PGND D5 PGND D6 PGND D7 D8 PGND D9 INTVCC D10 MPT2 D11 MPT3 D12 MARG1 PIN NAME E1 PGND E2 PGND E3 PGND E4 PGND E5 PGND E6 PGND E7 PGND E8 E9 PGND E10 E11 E12 DRVCC PIN NAME F1 PGND F2 PGND F3 PGND F4 PGND F5 PGND F6 PGND F7 PGND F8 PGND F9 PGND F10 F11 PGOOD F12 VFB PIN NAME G1 PGND G2 PGND G3 PGND G4 PGND G5 PGND G6 PGND G7 PGND G8 PGND G9 PGND G10 G11 SGND G12 PGOOD PIN NAME H1 PGND H2 PGND H3 PGND H4 PGND H5 PGND H6 PGND H7 PGND H8 PGND H9 PGND H10 H11 SGND H12 SGND PIN NAME J1 VOUT J2 VOUT J3 VOUT J4 VOUT J5 VOUT J6 VOUT J7 VOUT J8 VOUT J9 VOUT J10 VOUT J11 J12 VOSNS+ PIN NAME K1 VOUT K2 VOUT K3 VOUT K4 VOUT K5 VOUT K6 VOUT K7 VOUT K8 VOUT K9 VOUT K10 VOUT K11 VOUT K12 DIFFVOUT PIN NAME L1 VOUT L2 VOUT L3 VOUT L4 VOUT L5 VOUT L6 VOUT L7 VOUT L8 VOUT L9 VOUT L10 VOUT L11 VOUT L12 VOUT_LCL PIN NAME M1 VOUT M2 VOUT M3 VOUT M4 VOUT M5 VOUT M6 VOUT M7 VOUT M8 VOUT M9 VOUT M10 VOUT M11 VOUT M12 VOSNS– 4601ahvf 26 LTM4601AHV PACKAGE DESCRIPTION Pin Assignment Tables (Arranged by Pin Function) PIN NAME A1 A2 A3 A4 A5 A6 VIN VIN VIN VIN VIN VIN B1 B2 B3 B4 B5 B6 VIN VIN VIN VIN VIN VIN C1 C2 C3 C4 C5 C6 VIN VIN VIN VIN VIN VIN PIN NAME D1 D2 D3 D4 D5 D6 D8 PGND PGND PGND PGND PGND PGND PGND E1 E2 E3 E4 E5 E6 E7 PGND PGND PGND PGND PGND PGND PGND F1 F2 F3 F4 F5 F6 F7 F8 F9 PGND PGND PGND PGND PGND PGND PGND PGND PGND G1 G2 G3 G4 G5 G6 G7 G8 G9 PGND PGND PGND PGND PGND PGND PGND PGND PGND H1 H2 H3 H4 H5 H6 H7 H8 H9 PGND PGND PGND PGND PGND PGND PGND PGND PGND PIN NAME PIN NAME J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT A7 A8 A9 A10 A11 A12 INTVCC PLLIN TRACK/SS RUN COMP MPGM B12 fSET C12 MARG0 D12 MARG1 K1 K2 K3 K4 K5 K6 K7 K8 K9 K10 K11 VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT E12 DRVCC F12 VFB G12 PGOOD H12 SGND J12 VOSNS+ K12 DIFFVOUT L12 VOUT_LCL M12 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOSNS– M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M11 VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT VOUT PIN NAME B7 B8 B9 B10 B11 PGND PGND MPGM C7 C8 C9 C10 C11 PGND PGND MTP1 fSET D7 D8 D9 D10 D11 PGND INTVCC MTP2 MTP3 E8 E9 E10 E11 PGND - F10 F11 PGOOD G10 G11 SGND H10 H11 SGND J11 - 4601ahvf Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 27 LTM4601AHV RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC2900 Quad Supply Monitor with Adjustable Reset Timer Monitors Four Supplies, Adjustable Reset Timer LTC2923 Power Supply Tracking Controller Tracks Both Up and Down, Power Supply Sequencing LT3825/LT3837 Synchronous Isolated Flyback Controllers No Optocoupler Required, 3.3V, 12A Output, Simple Design LTM4600 10A DC/DC μModule Fast Transient Response, LTM4600HVMPV: –55°C to 125°C Tested LTM4601 12A DC/DC μModule with PLL, Output Tracking/ Margining and Remote Sensing Synchronizable, PolyPhase Operation to 48A, LTM4601-1 Version has no Remote Sensing LTM4602 6A DC/DC μModule Pin Compatible with the LTM4600 LTM4603 6A DC/DC μModule with PLL and Outpupt Tracking/ Margining and Remote Sensing Synchronizable, PolyPhase Operation, LTM4603-1 Version has no Remote Sensing, Pin Compatible with the LTM4601 LTM4604 4A Low Voltage DC/DC μModule 2.375V ≤ VIN ≤ 5.5V, 0.8V ≤ VOUT ≤ 5V, 9mm × 15mm × 2.3mm (Ultra-thin) LGA Package LTM4608 8A Low Voltage DC/DC μModule 2.375V ≤ VIN ≤ 5.5V, 0.6V ≤ VOUT ≤ 5V; 9mm × 15mm × 2.8mm LGA Package LTM8020 200mA, 36VIN DC/DC μModule 4V ≤ VIN ≤ 36V, 1.25V ≤ VOUT ≤ 5V, 6.25mm × 6.25mm × 2.32mm LGA Package LTM8021 500mA, 36VIN DC/DC μModule 3V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 5V, 11.25mm × 6.25mm × 2.8mm LGA Package LTM8022/ LTM8023 1A/2A, 36VIN DC/DC μModule Family 3.6V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 10V, Pin Compatible, 11.25mm × 9mm × 2.8mm LGA Package This product contains technology licensed from Silicon Semiconductor Corporation. 28 Linear Technology Corporation ® 4601ahvf LT 0208 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2008