LINER LT3991

LT3692A
Monolithic Dual Tracking
3.5A Step-Down Switching Regulator
Description
Features
Wide Input Range:
– Operation from 3V to 36V
– OVLO Protects Circuit Through 60V Transients
n Independent Supply, Shutdown, Soft-Start, UVLO,
Programmable Current Limit and Programmable
Power Good for Each 3.5A Regulator
n Die Temperature Monitor
n Adjustable/Synchronizable Fixed Frequency
Operation from 250kHz to 2MHz with Synchronized
Clock Output
n Independent Synchronized Switching Frequencies
Optimize Component Size
n Antiphase Switching
n Outputs Can Be Paralleled
n Flexible Output Voltage Tracking
n Low Dropout: 95% Maximum Duty Cycle
n5mm × 5mm QFN Package
n FMEA Compliant 38-Pin Exposed Pad TSSOP Package
n
Applications
Automotive Supplies
Distributed Supply Regulation
n
n
L, LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks
of Linear Technology Corporation. All other trademarks are the property of their respective owners.
The LT®3692A is a dual current mode PWM step-down
DC/DC converter with two internal 3.8A switches. Independent
input voltage, shutdown, feedback, soft-start, UVLO current
limit and comparator pins for each channel simplify complex
power supply tracking and sequencing requirements.
To optimize efficiency and component size, both converters have a programmable maximum current limit and are
synchronized to either a common external clock input, or
a resistor settable fixed 250kHz to 2MHz internal oscillator.
A frequency divider is provided for channel 1 to further
optimize component size. At all frequencies, a 180° phase
relationship between channels is maintained, reducing voltage ripple and component size. A clock output is available
for synchronizing multiple regulators.
Minimum input to output voltage ratios are improved by
allowing the switch to stay on through multiple clock cycles
only switching off when the boost capacitor needs recharging. Independent channel operation can be programmed
using the SHDN pin. Disabling both converters reduces
the total quiescent current to <10µA.
The LT3692A is an improved version of the LT3692 with
reduced minimum on-time.
Typical Application
Independent Synchronized Switching Frequencies
Extend Full Frequency Input Range
3.3V and 1.2V 2-Stage Dual Step-Down Multi-Frequency Converter
VOUT1
VIN1
5.5V TO 36V
4.7µF
SHDN1
BST1
VOUT1
3.3V
2.5A
550kHz
0.22µF
100k
47µF
4.7µH
24.9k
SHDN2
BST2
SW1
SW2
IND1
IND2
LT3692A
VOUT2
VOUT1
FB1
8.06k
PG
CMPI1
CMPI2
CMPO1
CMPO2
100k
13k
SS2
ILIM2
VC2
RT/SYNC
33pF 680pF
DIV
68.1k
102k
0.1µF
0.5µH
4.02k
FB2
SS1
ILIM1
VC1
0.1µF
CH1:
550kHz
VIN2
VIN1
CLKOUT
GND
TJ
FB1
100p
47µF
VOUT2
1.2V
1A
2.2MHz
CH2:
2.2MHz
VIN = 30V
3692A TA01b
8.06k
CLKOUT
2.2MHz
0.1µF
220pF
22pF
10nF
40.2k
33.2k
3692a TA01a
3692a TA01c
3692afb
1
LT3692A
Absolute Maximum Ratings
(Note 1)
VIN1/2, SHDN1/2, CMPO1/2........................................40V
VIN1/2 Transient (Note 2)............................................60V
SW1/2.....................................................................VIN1/2
BST1/2.......................................................................60V
BST1/2 Pin Above SW1/2...........................................25V
IND1/2, VOUT1/2..........................................................40V
FB1/2, CMPI1/2, SS1/2.................................................5V
RT/SYNC......................................................................5V
DIV, ILIM1/2..............................................................3.0V
VC1/2, TJ............................................................... ±100µA
Operating Junction Temperature Range (Note 3)
LT3692AEUH...................................... –40°C to 125°C
LT3692AIUH....................................... –40°C to 125°C
LT3692AHUH...................................... –40°C to 150°C
LT3692AEFE....................................... –40°C to 125°C
LT3692AIFE........................................ –40°C to 125°C
LT3692AHFE....................................... –40°C to 150°C
Storage Temperature Range................... –65°C to 150°C
Pin Configuration
SS1
VIN1
SW1
DNC*
IND1
DNC*
VOUT1
TOP VIEW
SHDN1
TOP VIEW
32 31 30 29 28 27 26 25
BST1 1
24 ILIM1
CMPO1 2
23 VC1
22 RT/SYNC
CMPI1 3
FB1 4
21 CLKOUT
33
GND
NC
1
38 SW1
IND1
2
37 NC
NC
3
36 VIN1
VOUT1
4
35 SHDN1
NC
5
34 SS1
BST1
6
33 ILIM1
CMPO1
7
32 VC1
CMPI1
8
31 NC
FB1
9
30 RT/SYNC
20 TJ
NC 10
CMPI2 6
19 DIV
FB2 11
CMPO2 7
18 VC2
CMPI2 12
27 DIV
CMPO2 13
26 VC2
FB2 5
17 ILIM2
BST2 8
SS2
SHDN2
VIN2
SW2
IND2
DNC*
DNC*
VOUT2
9 10 11 12 13 14 15 16
UH PACKAGE
32-LEAD (5mm × 5mm) PLASTIC QFN
θJA = 23°C/W, θJC(PAD) = 1.5°C/W
EXPOSED PAD (PIN 33) IS GND, MUST BE SOLDERED TO PCB
*DO NOT CONNECT
BST2 14
NC 15
VOUT2 16
NC 17
IND2 18
NC 19
39
GND
29 CLKOUT
28 TJ
25 ILIM2
24 SS2
23 SHDN2
22 VIN2
21 NC
20 SW2
FE PACKAGE
38-LEAD PLASTIC TSSOP
θJA = 17.5°C/W, θJC(PAD) = 3°C/W
EXPOSED PAD (PIN 39) IS GND, MUST BE SOLDERED TO PCB
3692afb
2
LT3692A
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3692AEUH#PBF
LT3692AEUH#TRPBF
3692A
32-Lead (5mm × 5mm) Plastic QFN
–40°C to 125°C
LT3692AIUH#PBF
LT3692AIUH#TRPBF
3692A
32-Lead (5mm × 5mm) Plastic QFN
–40°C to 125°C
LT3692AHUH#PBF
LT3692AHUH#TRPBF
3692A
32-Lead (5mm × 5mm) Plastic QFN
–40°C to 150°C
LT3692AEFE#PBF
LT3692AEFE#TRPBF
3692AFE
38-Lead Plastic TSSOP
–40°C to 125°C
LT3692AIFE#PBF
LT3692AIFE#TRPBF
3692AFE
38-Lead Plastic TSSOP
–40°C to 125°C
LT3692AHFE#PBF
LT3692AHFE#TRPBF
3692AFE
38-Lead Plastic TSSOP
–40°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
Electrical
Characteristics
The
l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VVIN1/2 = 15V unless otherwise specified. (Note 3)
PARAMETER
CONDITIONS
MIN
TYP
MAX
1.24
1.32
1.4
V
–1
0
1
µA
VIN1 Undervoltage Lockout (Note 4)
2.5
2.8
3.1
V
VIN Overvoltage Lockout Ch 1/2 (Note 5)
36
39
43
V
6
13
µA
SHDN Voltage Threshold Ch 1/2
SHDN Input Current Ch 1/2
l
VSHDN = 1.35V
VIN1 Shutdown Current
VSHDN = 0V
l
VIN2 Shutdown Current
VSHDN = 0V
l
VIN1 Quiescent Current
VSHDN = 2V
VIN2 Quiescent Current
VSHDN = 2V
UNITS
0
2
µA
3
4
5
mA
400
630
1000
µA
Feedback Voltage Ch 1/2
VVC1/2 = 1V
l
790
806
822
mV
Feedback Voltage Regulation
VVIN1/2 = 3V to 35V, VVC1/2 = 0.5V to 1.4V
l
780
806
830
mV
Feedback Voltage Offset Ch 1 to Ch 2
VVC1/2 = 1V
l
–13
0
13
mV
Feedback Bias Current Ch 1/2
VVC1/2 = 1V
l
0
85
200
nA
TJ Output Voltage (Note 6)
TJ = 25°C, ITJ = 25µA, Temperature = 25°C
ITJ = 25µA, Temperature = 125°C
ITJ = 25µA, Temperature = –40°C
TJ Error
Temperature = 25°C to 125°C
Error Amp gm Ch 1/2
VVC1/2 = 1V, IVC1/2 = ±10µA
250
1.23
–380
l
mV
V
mV
–100
0
100
mV
300
400
500
µMho
Error Amp Source Current Ch 1/2
VFB1/2 = 0.7V, VVC1/2 = 1V
17
25
33
µA
Error Amp Sink Current Ch 1/2
VFB1/2 =0.9V, VVC1/2 = 1V
20
28
36
µA
Error Amp High Clamp Ch 1/2
VFB1/2 = 0.7V
1.7
1.9
2.1
V
Error Amp Switching Threshold Ch 1/2
VFB1/2 = 0V
0.7
0.9
1.08
V
3692afb
3
LT3692A
Electrical
Characteristics
The
l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VVIN1/2 = 15V unless otherwise specified. (Note 3)
PARAMETER
CONDITIONS
Soft-Start Source Current Ch 1/2
VFB1/2 = 2V, VSS1/2 = 0.07V
Soft-Start VOH Ch 1/2
VFB1/2 = 2V
l
MIN
TYP
MAX
UNITS
9.5
12
14.5
µA
1.9
2.15
2.4
V
Soft-Start Sink Current Ch 1/2
VFB1/2 = 0.7V, VSS1/2 = 2V
0.7
1.4
2
mA
Soft-Start VOL Ch 1/2
VFB1/2 = 0V
120
160
200
mV
Soft-Start to Feedback Offset Ch 1/2
VVC1/2 = 1V, VSS1/2 = 0.4V
Soft-Start Sink Current Ch 1/2 POR
VFB1/2 = 2V, VSS1/2 = 0.14V (Note 7)
l
Soft-Start POR Threshold
Soft-Start SW Disable Ch 1/2
VFB1/2 = 0V (Note 7)
CMPI Bias Current Ch 1/2
VCMPI1/2 = 0.8V
CMPO Leakage Ch 1/2
VCMPI1/2 = 0.8V, VCMPO1/2 = 40V,
CMPI Threshold Ch 1/2
VCMPI1/2 Rising
CMPI Threshold Ch 1/2 of VFB1/2
VCMPI1/2 Rising (Note 8)
l
–12
0
12
mV
150
400
600
µA
70
100
140
mV
95
115
150
mV
–100
0
100
nA
70
500
nA
700
720
760
mV
86
90
94
%
85
mV
CMPI Hysteresis Ch 1/2
VCMPI1/2
35
60
CMPO Sink Current Ch 1/2
VCMPI1/2 = 0.6V, VCMPO1/2 = 0.2V,
200
300
RT/SYNC Reference Current
VRT/SYNC = 0.36V (E- and I-Grade)
VRT/SYNC = 0.36V (H-Grade)
11.3
11.2
12
12
12.7
13
µA
µA
Minimum Switching Frequency
RRT/SYNC =0Ω
50
110
150
kHz
Switching Frequency
RRT/SYNC = 28k
925
1
1075
kHz
Maximum Switching Frequency
RRT/SYNC =100k
2.25
2.5
3.0
MHz
l
l
Switching Phase Angle Ch 1 ≥ Ch 2
µA
185
DIV Reference Current
VDIV = 1V
CH1 DIV 2 Threshold
Deg
10.7
12
13.3
µA
RRT/SYNC = 0V
0.44
0.5
0.56
V
CH1 DIV 4 Threshold
RRT/SYNC = 0V
0.89
1.0
1.06
V
CH1 DIV 8 Threshold
RRT/SYNC = 0V
1.39
1.5
1.56
V
l
0.25
CLKOUT VOL
CLKOUT VOH
CLKOUT to SW1ON Delay ( tDCLKOSW1)
CLKOUT Rising
V
2
V
60
ns
CLKOUT to SW2ON Delay ( tDCLKOSW2)
CLKOUT Falling
30
ns
RT/SYNC to CLKOUT Delay ( tDRTSYNCH)
VRT/SYNC = 0V to 2V Rising Edge
300
ns
RT/SYNC to CLKOUT Delay ( tDRTSYNCL)
VRT/SYNC = 2V to 0V Falling Edge
150
ns
SYNC Frequency Range
SYNC Phase Angle Ch 1 to Ch 2
250
SYNC Frequency = 250kHz
2000
180
kHz
Deg
Minimum Switch On-Time Ch 1/2
140
ns
Minimum Switch Off-Time Ch 1/2
200
ns
3692afb
4
LT3692A
Electrical
Characteristics
The
l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VVIN1/2 = 15V unless otherwise specified. (Note 3)
PARAMETER
CONDITIONS
Minimum Boost for 100% DC Ch 1/2 (Note 9)
IND + VOUT Current Ch 1/2
VVOUT1/2 = 0V
VVOUT1/2 = 5V
ILIM1/2 Reference Current
VILIM = 0V
IND to VOUT Maximum Current Ch 1/2
MIN
TYP
MAX
1.6
2.2
2.6
UNITS
V
1.5
0.5
5
5
µA
µA
l
10
12
16
µA
VILIM1/2 = 0V, VVOUT = 1V (Note 10)
VILIM1/2 = 0V, VVOUT = 5V (Note 10)
VILIM1/2 = 0.5V, VVOUT = 1V (Note 10)
VILIM1/2 = 0.5V, VVOUT = 5V (Note 10)
VILIM1/2 = 1.5V, VVOUT = 1V (Note 10)
VILIM1/2 = 1.5V, VVOUT = 5V (Note 10)
l
l
0.8
1.25
1.4
1.8
3.7
3.7
1.8
2
2.2
2.6
4.6
4.6
2.6
3.0
3.6
3.8
5.8
5.8
A
A
A
A
A
A
l
1
10
Switch Leakage Current Ch 1/2
VSW1/2 = 0V
Switch Saturation Voltage Ch 1/2
ISW1/2 = 500mA, VBST1/2 = 18V
ISW1/2 = 3A, VBST1/2 = 18V
Boost Current Ch 1/2
ISW1/2 = 500mA, VBST1/2 = 8V
ISW1/2 = 3A, VBST1/2 = 8V
7
35
13
55
40
85
mA
mA
Minimum Boost Voltage Ch1/2 (Note 11)
ISW1/2 = 3A, VBST1/2 = 8V
1.6
2.2
3.0
V
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Absolute Maximum Voltage at VIN1/2 and SHDN1/2 pins is 60V for
nonrepetitive 1 second transients and 40V for continuous operation.
Note 3: The LT3692AEUH/LT3692AEFE is guaranteed to meet performance
specifications from 0°C to 125°C junction temperature. Specifications over
the –40°C to 125°C operating junction temperature range are assured by
design, characterization and correlation with statistical process controls.
The LT3692AIUH/LT3692AIFE is guaranteed over the full –40°C to 125°C
operating junction temperature range. The LT3692AHUH/LT3692AHFE is
guaranteed over the full –40°C to 150°C operating junction temperature
range. High junction temperatures degrade operating lifetimes. Operating
lifetime is derated at junction temperatures greater than 125°C.
Note 4: VIN undervoltage lockout is defined as the voltage which the VIN
pin must exceed for operation. The threshold guarantees that internal bias
lines are regulated and switching frequency is constant. Actual minimum
input voltage to maintain a regulated output will depend upon output
voltage and load current. See the Applications Information section.
Note 5: VIN overvoltage lockout is defined as the voltage when exceeded
halts converter operation. See the Applications Information section.
100
300
µA
mV
mV
Note 6: The TJ output voltage represents the temperature at the center
of the die while dissipating quiescent power. Due to switch power
dissipation and temperature gradients across the die, the TJ output
voltage measurement does not guarantee that absolute maximum junction
temperature will not be exceeded.
Note 7: An internal power on reset (POR) latch is set on the positive
transition of the SHDN1/2 pin through its threshold, thermal shutdown or
overvoltage lockout. The output of the latch activates current sources on
each SS pin which typically sink 400µA and discharge the SS capacitor.
The latch is reset when both SS pins are driven below the soft-start POR
threshold or the SHDN pin is taken below its threshold.
Note 8: The threshold is expressed as a percentage of the feedback
reference voltage for the channel.
Note 9: To enhance dropout operation, the output switch will be turned off
for the minimum off-time only when the voltage across the boost capacitor
drops below the minimum boost for 100% duty cycle threshold.
Note 10: The IND to VOUT maximum current is defined as the value of
current flowing from the IND pin to the VOUT pin which resets the switch
latch when the VC pin is at its high clamp.
Note 11: This is the minimum voltage across the boost capacitor needed
to guarantee full saturation of the internal power switch.
3692afb
5
LT3692A
Typical Performance Characteristics
VIN Overvoltage Threshold
vs Temperature
Shutdown Threshold and Minimum
Input Voltage vs Temperature
MINIMUM
INPUT VOLTAGE
3.0
VOLTAGE (V)
VOLTAGE (V)
2.5
2.0
SHUTDOWN
THRESHOLD VOLTAGE
1.5
1.0
0.5
0
–50 –25
0
41.0
10
40.5
9
40.0
8
39.5
7
CURRENT (µA)
3.5
39.0
38.5
38.0
3
36.5
1
810
1.25
4
1.00
0
–2
CH2
805
–4
CH1
–6
800
–50 –25
0
–8
25 50 75 100 125 150
TEMPERATURE (°C)
0.75
0.50
0.25 RTJ = 30k
TO GND
0
–0.25
–0.50
–50 –25
RTJ = 30k TO –1V
0
415
410
405
400
395
390
385
380
375
25 50 75 100 125 150
TEMPERATURE (°C)
370
–50 –30 –10 10 30 50 70 90 110 130 150
TEMPERATURE (°C)
3692a G05
3692a G06
Comparator Thresholds
vs Temperature
750
VSS = 0.4V
740
3
730
2
RISING
THRESHOLD
720
VOLTAGE (mV)
VOLTAGE (mV)
425
420
Soft-Start-to-Feedback Offset
vs Temperature
1
0
–1
710
700
690
680
–2
FALLING
THRESHOLD
670
–3
–4
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
Error Amplifier Transconductance
vs Temperature
TJ Output Voltage vs Temperature
3692a G04
4
IQ2
0
3692a G03
TRANSCONDUCTANCE (µMho)
6
VOLTAGE (V)
FEEDBACK VOLTAGE (V)
1.50
OFFSET VOLTAGE (mV)
8
2
OFFSET
0
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
3692a G02
FB Voltage and CH1-CH2 FB
Offset vs Temperature
815
4
2
3692a G01
820
5
37.0
0
IQ1
6
37.5
36.0
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
Shutdown Quiescent Current
vs Temperature
660
0
25 50 75 100 125 150
TEMPERATURE (°C)
3692a G07
650
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
3692a G08
3692afb
6
LT3692A
Typical Performance Characteristics
Comparator Sink Current
vs Temperature
Switching Phase vs Temperature
195
1800
1600
300
1400
250
200
150
100
191
189
1200
RRT/SYNC = 28.0k
1000
800
600
RRT/SYNC = 13.0k
0
0
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
185
183
179
RRT/SYNC = 0k
200
0
–50 –25
187
181
400
50
0
177
175
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
3692a G09
Synchronization Duty Cycles
vs Temperature
450
150
400
140
350
130
DELAY (ns)
100
100
90
SW1
300
CLKOUT
250
200
150
90
60
50
40
30
100
20
70
50
10
25 50 75 100 125 150
TEMPERATURE (°C)
0
–50 –25
0
0
25 50 75 100 125 150
TEMPERATURE (°C)
3695a G13
DIV Voltage Threshold
vs Temperature
3692a G14
Switch Saturation Voltage
vs Temperature
1.8
300
1.6
÷8
VOLTAGE (mV)
1.2
÷4
1.0
0.8
0.6
ISW = 3A
250
1.4
÷2
0.4
200
ISW = 1A
150
100
ISW = 500mA
50
0.2
0
–50 –25
MINIMUM RT/SYNC DUTY CYCLE
0
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
3692a G12
VOLTAGE (V)
0
MAXIMUM RT/SYNC DUTY CYCLE
70
80
60
–50 –25
RT/SYNC FREQUENCY = 1MHz
80
DUTY CYCLE (%)
160
110
25 50 75 100 125 150
TEMPERATURE (°C)
3692a G11
RT/SYNC-to-CLKOUT and SW1
Delay vs Temperature
120
0
3692a G10
CLKOUT-to-SW1 Delay
vs Temperature
DELAY (ns)
193
RRT/SYNC = 44.2k
PHASE (DEG)
SINK CURRENT AT VCMPO = 0.4V
350
FREQUENCY (kHz)
CURRENT (µA)
400
Switching Frequency
vs Temperature
0
25 50 75 100 125 150
TEMPERATURE (°C)
3695a G15
0
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
3692a G16
3692afb
7
LT3692A
Typical Performance Characteristics
Switch Peak Current
vs Temperature
100
5.0
90
4.5
80
4.0
3A
60
50
40
30
10
0
2.50
VILIM = 0.5V
2.5
VILIM = 0V
2.0
1.5
0
–50 –25
1.75
0
1.00
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
0
25 50 75 100 125 150
TEMPERATURE (°C)
3692a G19
3692a G18
CLKOUT Frequency
vs RT/SYNC Resistance
5.0V Efficiency and Power Loss
3.3V Efficiency and Power Loss
90
2500
2250
85
2000
EFFICIENCY
3.0
90
2.5
85
3.0
2.5
1500
1250
1000
750
500
80
2.0
75
70
1.0
VIN = 12V
FSW = 1MHz
CH1 = 5V
CH2 = 0V
65
250
0
10
20 30 40 50 60 70
RT/SYNC RESISTANCE (kΩ)
80
60
0
0.5
1.0 1.5 2.0 2.5 3.0
OUTPUT CURRENT (A)
3.5
4
2.0
1.5
75
POWER LOSS
1.0
70
0.5
65
0
60
0
0.5
VIN = 12V
FREQ = 1MHz 0.5
CH1 = 3.3V
CH2 = 0V
0
1 1.5 2 2.5 3 3.5 4
OUTPUT CURRENT (A)
3692a G21
3692a G20
2.5V Efficiency and Power Loss
3692a G22
1.8V Efficiency and Power Loss
3.0
2.5
80
80
2.0
75
2.0
75
1.5
70
1.5
EFFICIENCY
85
VIN = 12V
FSW = 1MHz
CH1 = 2.5V
CH2 = 0V
65
60
1.0
0
0.5
1.0 1.5 2.0 2.5 3.0
OUTPUT CURRENT (A)
3.5
4
3692a G23
POWER LOSS
65
0.5
60
0
55
2.5
EFFICIENCY
1.0
VIN = 12V
FSW = 1MHz
CH1 = 1.8V
CH2 = 0V
0
0.5
1.0 1.5 2.0 2.5 3.0
OUTPUT CURRENT (A)
PLOSS (W)
POWER LOSS
70
EFFICIENCY (%)
85
PLOSS (W)
3.0
90
EFFICIENCY (%)
1.5
POWER LOSS
80
PLOSS (W)
EFFICIENCY (%)
1750
EFFICIENCY (%)
EFFICIENCY
PLOSS (W)
CLKOUT FREQUENCY (kHz)
2.00
1.25
0.5
3692a G17
0
2.25
1.50
1.0
25 50 75 100 125 150
TEMPERATURE (°C)
ISW = 3A
2.75
VILIM = 1.5V
3.0
0.5A
0
–50 –25
3.00
3.5
1A
20
Minimum Boost Voltage
vs Temperature
VOLTAGE (V)
70
PEAK CURRENT (A)
BOOST CURRENT (mA)
Boost Current vs Temperature
3.5
0.5
4
0
3692a G24
3692afb
8
LT3692A
Pin Functions
BST1/BST2: The BST pin provides a higher than VIN base
drive to the power NPN to ensure a low switch drop. If the
voltage between the BST pin and the VIN pin is less than
the voltage required to fully turn on the power NPN, the
power switch is turned off to recharge the BST capacitor.
CMPI1/CMPI2: The CMPI pin is an input to a comparator with a threshold of 720mV and 60mV of hysteresis.
Connecting the CMPI pin to the FB pin will generate a
power good signal when the output is within 90% of its
regulated value.
CMPO1/CMPO2: The CMPO pin is an open-collector
output that sinks current when the CMPI pin falls below
its threshold. For a typical input voltage above 2.8V, its
output state remains true, although during shutdown, VIN1
undervoltage lockout or thermal shutdown, its current sink
capability is reduced. The COMPO pins can be left open
circuit or tied together to form a single power good signal.
DIV: The voltage present at the DIV pin determines the ratio
of channel 1 frequency to the master clock frequency set
by the RT/SYNC pin. The DIV pin is driven by an internal
current source with a typical value of 12µA which allows
a single resistor from the DIV pin to ground to set the
DIV voltage and resulting channel 1 frequency divider.
Ratios of 1, 2, 4 and 8 are available. See the Applications
Information section for more information.
DNC: Do Not Connect.
GND: The exposed pad pin is the only ground connection for the device. The exposed pad should be soldered
to a large copper area to reduce thermal resistance. The
GND pin is common to both channels and also serves as
small-signal ground. For ideal operation all small-signal
ground paths should connect to the GND pin at a single
point avoiding any high current ground returns.
ILIM1/ILIM2: The voltage present at the ILIM pin determines the peak inductor current for the channel. The ILIM
pin is driven by an internal current source with a typical
value of 12µA. A resistor from the ILIM pin to ground sets
the ILIM voltage. The maximum current limit range is 4.8A
to 2A when the ILIM voltages are 1.5V and 0V respectively.
IND1/IND2: The IND pin is the input to the internal sense
resistor that measures current flowing in the inductor.
When the current in the resistor exceeds the current dictated by the VC pin, the SW latch is held in reset, disabling
the output switch. Bias current flows out of the IND pin.
RT/SYNC: The voltage present at the RT/SYNC pin determines the constant switching frequency. The RT/SYNC
pin is driven by an internal current source with a typical
value of 12µA which allows a single resistor from the RT/
SYNC pin to ground to set the RT/SYNC voltage and resulting switching frequency. Minimum switching frequency
is typically 110kHz when VRT/SYNC is 0V and maximum
switching frequency is typically 2.5MHz when VRT/SYNC
is above 950mV.
Driving the RT/SYNC pin with an external clock signal will
synchronize the switch to the applied frequency. Synchronization occurs on the rising edge of the clock signal after
the clock signal is detected. Each rising clock edge initiates
an oscillator ramp reset. A gain control loop servos the
oscillator charging current to maintain constant oscillator
amplitude. Hence, the slope compensation and channel
phase relationship remain unchanged. If the clock signal
is removed, the oscillator reverts to resistor mode after
the synchronization detection circuitry times out. The clock
source impedance should be set such that the current out
of the RT/SYNC pin in resistor mode generates a frequency
roughly equivalent to the synchronization frequency. See
the Applications Information section for more information.
FB1/FB2: The FB pin is the negative input to the error amplifier. The output switches to regulate this pin to 806mV
with respect to the exposed ground pad. Bias current
flows out of the FB pin.
3692afb
9
LT3692A
pin functions
SHDN1/SHDN2: The shutdown pin is used to control each
channel’s operation. In addition to controlling channel 1,
the SHDN1 pin also activates control circuitry for both
channels and must be present for channel 2 to operate.
When SHDN1 is below its threshold, quiescent current is
reduced to a typical value of 6µA. Independent channel
UVLO can be programmed by connecting the SHDN pin to
an input voltage divider. See the Applications Information
section for more information. If the shutdown features are
not used, the SHDN pin should be tied to VIN.
SS1/SS2: Current flowing out the SS pin into an external
capacitor defines the rise time of the output voltage. When
the SS pin is lower than the 0.806V reference, the feedback
is regulated to the SS voltage. When the SS pin exceeds
the reference voltage, the output will regulate the FB pin
voltage to 0.806V and the SS pin will continue to rise until
its clamp voltage. During an output overload, the VC pin is
driven above the maximum switch current level activating
its voltage clamp. When the VC clamp is activated, the SS
pin is discharged until the output reaches a regulation point
that the maximum output current can maintain. When the
overload condition is removed, the output soft starts from
that voltage. In the case of a SHDN or thermal shutdown
event, a power on reset latch ensures the capacitors on
both channels are fully discharged before either is released.
Connecting both SS pins together ensures the outputs
track together.
CLKOUT: The CLKOUT pin generates a square wave of 0V
to 2.5V which is synchronized to the internal oscillator. If
the switching frequency is set by an external resistor the
resultant clock duty cycle will be 50%. If the RT/SYNC pin
is driven by an external clock source, the resultant CLKOUT
duty cycle will mirror the external source.
TJ: The TJ pin outputs a voltage proportional to junction
temperature. The pin is 250mV for 25°C and has a slope
of 10mV/°C. See the Applications Information section for
more information.
VC1/VC2: The VC pin is the output of the error amplifier
and the input to the peak switch current comparator. It is
normally used for frequency compensation, but can also
be used as a current clamp or control loop override. If
the error amplifier drives VC above the maximum switch
current level, a voltage clamp activates. This indicates that
the output is overloaded and current is pulled from the SS
pin reducing the regulation point.
VIN1: The VIN1 pin powers the internal control circuitry for
both channels and is monitored by overvoltage/undervoltage lockout comparators. The VIN1 pin is also connected
to the collector of channel 1’s on-chip power NPN switch.
The VIN1 pin has high dI/dt edges and must be decoupled
to ground close to the pin of the device.
VIN2: The VIN2 pin powers the output stage for channel 2
and is monitored by overvoltage/undervoltage lockout
comparators. VIN1 voltage must be greater than typically
2.8V for VIN2 operation. The VIN2 pin is also the collector
of channel 2’s on-chip power NPN switch. The VIN2 pin
has high dI/dt edges and must be decoupled to ground
close to the pin of the device.
VOUT1/VOUT2: The VOUT pin is the output to the internal
sense resistor that measures current flowing in the inductor. When the current in the resistor exceeds the current
dictated by the VC pin, the SW latch is held in reset disabling
the output switch. Bias current flows out of the VOUT pin.
SW1/SW2: The SW pin is the emitter of the internal power
NPN. At switch off, the inductor will drive this pin below
ground with a high dV/dt. An external Schottky catch
diode to ground, close to the SW pin and respective VIN
decoupling capacitor’s ground, must be used to prevent
this pin from excessive negative voltages.
3692afb
10
LT3692A
Block Diagram
VIN1
1.32V
SHDN1
+
–
+
–
VIN1
39V
CHANNEL 1
THERMAL
SHUTDOWN
2.5V
12µA
SS1
S
–
+
90mV
–
+
S
PRE
PRE
Q
R
DROPOUT
ENHANCEMENT
BST1
DRIVER
CIRCUITRY
SW1
IND1
+
–
Q
R
VOUT1
VC1
R1
FB1
2.5V
ILIM1
RLIM
CMPI1
12µA
SLOPE
COMPENSATION
2.5V
2.5V
DIV
0.806V
0.72V
CMPO1
+
–
12µA
RT/SYNC
R3
+
+
–
R2
12µA
OSCILLATOR
AND AGC
CLK1
VIN1
MASTER CLOCK
2.8V
+
–
CLK2 TO CHANNEL 2
INTERNAL
REGULATOR
AND
REFERENCES
2.5V
TJ
CLKOUT
GND
RDIV
3692a F01
Figure 1. LT3692A Block Diagram
The LT3692A is a dual channel, constant frequency, current
mode buck converter with internal 3.8A switches. Each
channel can be independently controlled with the exception
that VIN1 must be above the typically 2.8V undervoltage
lockout threshold to power the common internal regulator,
oscillator and thermometer circuitry.
If the SHDN1 pin is taken below its 1.32V threshold the
LT3692A will be placed in a low quiescent current mode. In
this mode the LT3692A typically draws 6µA from VIN1 and
<1µA from VIN2. When the SHDN pin is driven above 1.32V, the
internal bias circuits turn on generating an internal regulated
voltage, 0.806VFB, 12µA RT/SYNC, DIV and ILIM current
references, and a POR signal which sets the soft-start latch.
Once the internal reference reaches its regulation point,
the internal oscillator will start generating a master clock
signal for the two regulators at a frequency determined by
the voltage present at the RT/SYNC pin. The channel 1 clock
is then divided by 1, 2, 4 or 8 depending on the voltage
present at the DIV pin. Channel 2’s clock runs at the master
clock frequency with a 180° phase shift from channel 1.
Alternatively, if a synchronization signal is detected by
the LT3692A the RT/SYNC pin, the master clock will be
generated at the incoming frequency on the rising edge
of the synchronization pulse with channel 1 in phase with
the synchronization signal. Frequency division and phase
remains the same as the internally generated master clock.
In addition, the internal slope compensation will be automatically adjusted to prevent subharmonic oscillation
during synchronization. In either mode of oscillator operation, a square wave with the master clock frequency,
synchronized to channel 1 is present at the CLKOUT pin.
The two regulators are constant frequency, current mode
step-down converters. Current mode regulators are controlled by an internal clock and two feedback loops that
control the duty cycle of the power switch. In addition to
3692afb
11
LT3692A
Block Diagram
the normal error amplifier, there is a current sense amplifier
that monitors switch current on a cycle-by-cycle basis.
This technique means that the error amplifier commands
current to be delivered to the output rather than voltage.
A voltage fed system will have low phase shift up to the
resonant frequency of the inductor and output capacitor,
then an abrupt 180° shift will occur. The current fed system will have 90° phase shift at a much lower frequency,
but will not have the additional 90° shift until well beyond
the LC resonant frequency. This makes it much easier to
frequency compensate the feedback loop and also gives
much quicker transient response.
The Block Diagram in Figure 1 shows only one of the
switching regulators whose operation will be discussed
below. The additional regulator will operate in a similar
manner with the exception that its clock will be 180° outof-phase with the other regulator.
When, during power-up, an internal POR signal sets
the soft-start latch, both SS pins will be discharged to
ground to ensure proper start-up operation. When the SS
pin voltage drops below 100mV, the VC pin is driven low
disabling switching and the soft-start latch is reset. Once
the latch is reset the soft-start capacitor starts to charge
with a typical value of 12µA.
As the voltage rises above 115mV on the SS pin, the VC
pin will be driven high by the error amplifier. When the
voltage on the VC pin exceeds 0.9V, the clock set-pulse sets
the driver flip-flop, which turns on the internal power NPN
switch. This causes current from VIN, through the NPN
switch, inductor and internal sense resistor to increase.
When the voltage drop across the internal sense resistor
exceeds a predetermined level set by the voltage on the
VC pin, the flip-flop is reset and the internal NPN switch
is turned off. Once the switch is turned off the inductor
will drive the voltage at the SW pin low until the external
Schottky diode starts to conduct, decreasing the current
in the inductor. The cycle is repeated with the start of each
clock cycle. However, if the internal sense resistor voltage
exceeds the predetermined level at the start of a clock cycle,
the flip-flop will not be set resulting in a further decrease
in inductor current. Since the output current is controlled
by the VC voltage, output regulation is achieved by the
error amplifier continually adjusting the VC pin voltage.
The error amplifier is a transconductance amplifier that
compares the FB voltage to the lowest voltage present at
either the SS pin or an internal 806mV reference. Compensation of the loop is easily achieved with a simple capacitor
or series resistor/capacitor from the VC pin to ground.
The regulators’ maximum output current occurs when
the VC pin is driven to its maximum clamp value by the
error amplifier. The value of the typical maximum switch
current can be programmed from 4.8A to 2A by placing
a resistor from the ILIM pin to ground.
Since the SS pin is driven by a constant current source, a
single capacitor on the soft-start pin will generate controlled
linear ramp on the output voltage.
If the current demanded by the output exceeds the maximum current dictated by the VC pin clamp, the SS pin
will be discharged, lowering the regulation point until the
output voltage can be supported by the maximum current.
Once the overload condition is removed, the regulator will
soft-start from the overload regulation point.
Shutdown control, VIN overvoltage, or thermal shutdown
will set the soft-start latch, resulting in a complete softstart sequence.
The switch driver operates from either the VIN or BST voltage. An external diode and capacitor are used to generate
a drive voltage higher than VIN to saturate the output NPN
and maintain high efficiency. If the BST capacitor voltage
is sufficient, the switch is allowed to operate to 100% duty
cycle. If the boost capacitor discharges towards a level
insufficient to drive the output NPN, a BST pin comparator forces a minimum cycle off time, allowing the boost
capacitor to recharge.
A comparator with a threshold of 720mV and 60mV of
hysteresis is provided for detecting error conditions. The
CMPO output is an open-collector NPN that is off when
the CMPI pin is above the threshold allowing a resistor
to pull the CMPO pin to a desired voltage.
The voltage present at the TJ pin is proportional to the junction
temperature of the LT3692A. The TJ pin will be 250mV for a
die temperature of 25°C and will have a slope of 10mV/°C.
3692afb
12
LT3692A
Applications Information
Choosing the Output Voltage
The output voltage is programmed with a resistor divider
between the output and the FB pin. Choose the 1% resistors according to:
 V

R1= R2 •  OUT – 1
 0.806 
R2 should be 10k or less to avoid bias current errors. Reference designators refer to the Block Diagram in Figure 1.
Choosing the Switching Frequency
The LT3692A switching frequency is set by resistor R3 in
Figure 1. The RT/SYNC pin is driven by a 12µA current
source. Setting resistor R3 sets the voltage present at
the RT/SYNC pin which determines the master oscillator
frequency as illustrated in Figure 2. The R3 resistance
(in kΩ) may be calculated from the desired switching
frequency (in kHz) by the equation:
for frequencies between 150kHz and 2250kHz. A 0V to
2.5V square wave with the same frequency as the master
oscillator and in phase with channel 1 is output via the
CLKOUT pin. The CLKOUT signal can be used to synchronize multiple switching regulators.
To alleviate duty cycle restrictions due to minimum switchon times, channel 1’s switching frequency can be divided
from the master clock by 1, 2, 4 or 8 determined by resistor
RDIV in Figure 1. Channel 2’s switching frequency is not
affected by the DIV pin. The DIV pin is driven by a 12µA
current source. Setting resistor RDIV sets the voltage present at the DIV pin which determines the divisor as shown
in Table 1. The DIV pin doesn’t have any input hysteresis
near the ratio thresholds.
Table 1. Channel 1 Divisor vs VDIV
DIV VOLTAGE
R3 = 1.86E-6 • FSW2 + 2.81E-2 • FSW –1.76
2250
CLKOUT FREQUENCY (kHz)
RDIV
VDIV < 0.5V
1
0
0.5V < VDIV < 1.0V
2
61.9k
1.0V < VDIV < 1.5V
4
102k
1.5V < VDIV
8
150k
The switching frequency is typically set as high as possible to reduce overall solution size. The LT3692A employs
techniques to enhance dropout at high frequencies but
efficiency and maximum input voltage decrease due to
switching losses and minimum switch-on times.
2500
2000
1750
1500
1250
The maximum recommended frequency can be approximated by the equation:
1000
750
500
Frequency (Hz) =
250
0
FREQUENCY RATIO
0
10
20 30 40 50 60 70
RT/SYNC RESISTANCE (kΩ)
80
3692a F02
Figure 2. Switching Frequency vs RT/SYNC Resistance
VOUT + VD
1
•
VIN – VSW + VD tON(MIN)
where VD is the forward voltage drop of the catch diode (D1
Figure 2), VSW is the voltage drop of the internal switch,
and tON(MIN) in the minimum on-time of the switch.
3692afb
13
LT3692A
Applications Information
Table 2. Efficiency and Size Comparisons for Different RRT/SYNC Values, 3.3V Output
FREQUENCY
RT/SYNC
EFFICIENCY
VVIN1/2 = 12V
VIN(MAX)†
L*
C*
C + L (Area)
250kHz
5.90k
88%
39V
12µH
120µF
59.8mm2
500kHz
13.0k
87%
39V
5.6µH
60µF
54.6mm2
1000kHz
28.0k
84%
26V
3.3µH
30µF
51.9mm2
1500kHz
44.2k
82%
18V
1.5µH
22µF
46.9mm2
2250kHz
69.8k
78%
12V
1µH
15µF
19.1mm2
† V
IN(MAX) is defined as the highest typical input voltage that maintains constant output voltage ripple.
*Inductor and capacitor values chosen for stability and constant ripple current.
The following example along with the data in Table 2
illustrates the trade-offs of switch frequency selection for
a single input voltage system.
Example.
VIN = 25V, VOUT = 3.3V, IOUT = 2.5A, tON(MIN) = 140ns,
VD = 0.6V, VSW = 0.4V:
Max Frequency =
3.3 + 0.6
1
•
~ 1.1MHz
25 – 0.4 + 0.6 140ns
RT/SYNC ~ 31.6kΩ (Figure 2 )
Input Voltage Range
Once the switching frequency has been determined, the
input voltage range of the regulator can be determined. The
minimum input voltage is determined by either the LT3692A’s
minimum operating voltage of ~2.8V, or by its maximum duty
cycle. The duty cycle is the fraction of time that the internal
switch is on during a clock cycle. Unlike most fixed frequency
regulators, the LT3692A will not switch off at the end of each
clock cycle if there is sufficient voltage across the boost
capacitor (C3 in Figure 1) to fully saturate the output switch.
Forcing switch-off for a minimum time will only occur at the
end of a clock cycle when the boost capacitor needs to be
recharged. This operation has the same effect as lowering the
clock frequency for a fixed off time, resulting in a higher duty
cycle and lower minimum input voltage. The resultant duty
cycle depends on the charging times of the boost capacitor
and can be approximated by the following equation:
DCMAX =
1
1
B
where B is 3A divided by the typical boost current from
the Electrical Characteristics table.
1+
This leads to a minimum input voltage of:
VIN(MIN) =
VOUT + VD
– VD + VSW
DCMAX
where VSW is the voltage drop of the internal switch.
Figure 4 shows a typical graph of minimum input voltage
vs load current for the 3.3V output shown in Figure 15.
6
tP
VOUT = 3.3V
5
START-UP
tP/2
VOLTAGE (V)
SW1
tP
SW2
tP/2
tP
3
2
1
CLKOUT
tDCLKOSW1
RUNNING
4
0
3692a F03
tDCLKOSW2
Figure 3. Timing Diagram RT/SYNC = 28.0k, tP = 1µs, VDIV = 0V
0
500 1000 1500 2000 2500 3000 3500
CURRENT (mA)
3692a F04
Figure 4. Minimum Input Voltage vs Load Current
3692afb
14
LT3692A
Applications Information
The maximum input voltage is determined by the absolute
maximum ratings of the VIN and BST pins and by the
frequency and minimum duty cycle. The minimum duty
cycle is defined as:
DCMIN = tON(MIN) • Frequency
Maximum input voltage as:
VIN(MAX) =
VOUT + VD
– VD + VSW
DCMIN
Example:
Note that the LT3692A will regulate if the input voltage is
taken above the calculated maximum voltage as long as
maximum ratings of the VIN and BST pins are not violated.
However operation in this region of input voltage will
exhibit pulse-skipping behavior.
Example:
VOUT = 3.3V, IOUT = 1A, frequency = 1MHz, temperature
= 25°C, VSW = 0.1V, B = 50 (from boost characteristics
specification), VD = 0.4V, tON(MIN) = 140ns:
DCMAX =
1
1+
VIN(MIN) =
1
50
DCMIN1 = tON(MIN1) • Frequency/2 = 0.07
A good first choice for the LT3692A inductor value is:
L=
VOUT
f
With this value the maximum load current will be ~3.5A,
independent of input voltage. The inductor’s RMS current rating must be greater than your maximum load
current and its saturation current should be higher than
the maximum peak switch current, and will reduce the
output voltage ripple.
If the maximum load for a single channel is lower than
2.5A, then you can decrease the value of the inductor and
operate with higher ripple current, or you can adjust the
maximum switch current for the channel via the ILIM pin.
This allows you to use a physically smaller inductor, or one
with a lower DCR resulting in higher efficiency.
2 • tP
SW1
tP
SW2
The peak inductor and switch current is:
tP
CLKOUT
tDCLKOSW1
3.3 + 0.4
– 0.4 + 0.1= >39V
0.07
where f is frequency in MHz and L is in µH.
3.3 + 0.4
– 0.4 + 0.1= 26.1V
0.14
tP/2
VIN1(MAX) =
Inductor Selection and Maximum Output Current
3.3 + 0.4
– 0.4 + 0.1= 3.48V
0.98
1/(2 • tP)
VOUT = 3.3V, IOUT = 1A, frequency = 1MHz, temperature
= 25°C, VSW = 0.1V, B = 50 (from boost characteristics
specification), VD = 0.4V, tON(MIN) = 140ns. VDIV = 0.75V.
= 98%
DCMIN = tON(MIN) • Frequency = 0.14
VIN(MAX) =
In cases where multiple input voltages are present, or the
VIN/VOUT ratio for channel 1 is significantly different than
channel 2, channel 1’s frequency can be divided by a factor
of 2, 4 or 8 from the programmed value by setting the DIV
pin resistor to the appropriate value. Dividing channel 1’s
frequency will increase the maximum input voltage by the
same ratio. Channel 1’s external components will have to
be chosen according to the resulting frequency.
3692a F05
tDCLKOSW2
Figure 5. Timing Diagram RT/SYNC = 28.0k,
tP = 1µs, VDIV = 0.75V
ISW(PK) = IL(PK) = IOUT +
∆IL
2
To maintain output regulation, this peak current must be
less than the LT3692A’s switch current limit, ILIM. ILIM
3692afb
15
LT3692A
Applications Information
can be set between 2A and 4.8A for each channel via a
resistor from the ILIM pin to ground. The ILIM pin is
driven by a 12µA current source. Setting resistor R LIM
sets the voltage present at the ILIM pin which determines
the maximum switch current as illustrated in Figure 6. A
capacitor from the ILIM pin to ground, or a resistor divider
from the output, can be used to limit the peak current during start-up. If a capacitor is used it must be discharged
before power-up to ensure proper operation (see 3.3V and
2.5V Dual Step-Down Converter in Typical Applications).
Referring to Figure 6, as the peak current limit is reduced,
slope compensation further reduces the peak current with
increasing duty cycle.
When the ILIM pin is used to reduce the peak switch current, the equation for inductor choice becomes:
50 • VOUT
L=
for RILIM > 24.9kΩ
f • RILIM
where f is frequency in MHz, L in µH and R in kΩ.
4.5
PEAK SWITCH CURRENT (A)
4.0
When the LT3692A’s input supplies are operated at different
input voltages, an input capacitor sized for that channel
should be placed as close as possible to the respective
VIN pins.
A caution regarding the use of ceramic capacitors at the
input. A ceramic input capacitor can combine with stray
inductance to form a resonant tank circuit. If power is
applied quickly (for example by plugging the circuit into
a live power source) this tank can ring, doubling the input
voltage and damaging the LT3692A. The solution is to
either clamp the input voltage or dampen the tank circuit
by adding a lossy capacitor in parallel with the ceramic
capacitor. For details, see Application Note 88.
Output Capacitor Selection
Typically step-down regulators are easily compensated with
an output crossover frequency that is 1/10 of the switching frequency. This means that the time that the output
capacitor must supply the output load during a transient
step is ~2 or 3 switching periods. With an allowable 1%
drop in output voltage during the step, a good starting
value for the output capacitor can be expressed by:
3.5
CVOUT =
Max Load Step
Frequency • 0.01• VOUT
3.0
2.5
Example:
2.0
VOUT = 3.3V, Frequency = 1MHz, Max Load Step = 2A.
1.5
1.0
0 10 20 30 40 50 60 70 80 90 100
ILIM PIN RESISTOR (kΩ)
3692a F06
Figure 6. Peak Switch Current vs ILIM Resistor
Input Capacitor Selection
Bypass the inputs of the LT3692A circuit with a 4.7µF or
higher ceramic capacitor of X7R or X5R type. A lower
value or a less expensive Y5V type can be used if there
is additional bypassing provided by bulk electrolytic or
tantalum capacitors.
CVOUT =
2
= 60µF
1E6 • 0.01• 3.3V
The calculated value is only a suggested starting value.
Increase the value if transient response needs improvement
or reduce the capacitance if size is a priority. The output
capacitor filters the inductor current to generate an output
with low voltage ripple. It also stores energy in order to
satisfy transient loads and to stabilize the LT3692A’s control
loop. The switching frequency of the LT3692A determines
the value of output capacitance required. Also, the current
mode control loop doesn’t require the presence of output
capacitor series resistance (ESR). For these reasons, you
are free to use ceramic capacitors to achieve very low
output ripple and small circuit size.
3692afb
16
LT3692A
Applications Information
You can also use electrolytic capacitors. The ESRs of most
aluminum electrolytics are too large to deliver low output
ripple. Tantalum and newer, lower ESR organic electrolytic
capacitors intended for power supply use, are suitable
and the manufacturers will specify the ESR. The choice of
capacitor value will be based on the ESR required for low
ripple. Because the volume of the capacitor determines
its ESR, both the size and the value will be larger than a
ceramic capacitor that would give you similar ripple performance. One benefit is that the larger capacitance may
give better transient response for large changes in load
current. Table 3 lists several capacitor vendors.
BST Pin Considerations
Table 3
VENDOR
TYPE
Taiyo Yuden
Ceramic X5R, X7R
SERIES
AVX
Ceramic X5R, X7R
Tantalum
Kemet
Tantalum
TA Organic
AL Organic
T491, T494, T495
T520
A700
Sanyo
TA/AL Organic
POSCAP
Panasonic
AL Organic
SP CAP
TDK
Ceramic X5R, X7R
Catch Diode
The diode D1 conducts current only during switch-off
time. Use a Schottky diode to limit forward voltage drop to
increase efficiency. The Schottky diode must have a peak
reverse voltage that is equal to regulator input voltage and
sized for average forward current in normal operation.
Average forward current can be calculated from:
ID(AVG) =
IOUT
• ( VIN – VOUT )
VIN
With a shorted condition, diode current will increase to the
typical value determined by the peak switch current limit
of the LT3692A set by the ILIM pin. This is safe for short
periods of time, but it would be prudent to check with the
diode manufacturer if continuous operation under these
conditions can be tolerated.
The capacitor and diode tied to the BST pin generate a
voltage that is higher than the input voltage. In most cases
a 0.47µF capacitor and a small Schottky diode (such as the
CMDSH-4E) will work well. To ensure optimal performance
at duty cycles greater than 80%, use a 0.5A Schottky
diode (such as a PMEG4005). Almost any type of film or
ceramic capacitor is suitable, but the ESR should be <1Ω
to ensure it can be fully recharged during the off time of
the switch. The capacitor value can be approximated by:
CBST =
IOUT(MAX) • VOUT
5 • VIN ( VOUT – 2) • f
where IOUT(MAX) is the maximum load current.
Figure 7 shows four ways to arrange the boost circuit. The
BST pin must be more than 3V above the SW pin for full
efficiency. Generally, for outputs of 3.3V and higher the
standard circuit (Figure 7a) is the best. For lower output
voltages the boost diode can be tied to the input (Figure 7b). The circuit in Figure 7a is more efficient because
the BST pin current comes from a lower voltage source.
Figure 7c shows the boost voltage source from available
DC sources that are greater than 3V. The highest efficiency
is attained by choosing the lowest boost voltage above 3V.
For example, if you are generating 3.3V and 1.8V and the
3.3V is on whenever the 1.8V is on, the 1.8V boost diode
can be connected to the 3.3V output. In any case, you
must also be sure that the maximum voltage at the BST
pin is less than the maximum specified in the Absolute
Maximum Ratings section.
The boost circuit can also run directly from a DC voltage
that is higher than the input voltage by more than 3V, as
in Figure 7d. The diode is used to prevent damage to the
LT3692A in case VX is held low while VIN is present. The
circuit saves several components (both BST pins can be
tied to D2). However, efficiency may be lower and dissipation in the LT3692A may be higher. Also, if VX is absent,
the LT3692A will still attempt to regulate the output, but
will do so with very low efficiency and high dissipation
because the switch will not be able to saturate, dropping
1.5V to 2V in conduction.
3692afb
17
LT3692A
Applications Information
D2
VIN
VIN
BST
C3
D2
VIN
SW
VIN
LT3692A
GND
(7b)
D2
VX > VIN + 3V
VIN
BST
C3
VIN
SW
VIN
BST
SW
LT3692A
LT3692A
IND
VOUT
VBST – VSW = VX
VBST(MAX) = VIN + VX
VX(MIN) = 3V
VOUT < 3V
GND
VBST – VSW = VIN
VBST(MAX) = 2 • VIN
D2
VIN
SW
IND
VOUT
VOUT
(7a)
VX = LOWEST VIN
OR VOUT > 3V
C3
LT3692A
IND
VOUT
VBST – VSW = VOUT
VBST(MAX) = VIN + VOUT
BST
IND
VOUT
VOUT < 3V
GND
VBST – VSW = VX
VBST(MAX) = VX
VX(MIN) = VIN + 3V
(7c)
VOUT < 3V
GND
3692a F07
(7d)
Figure 7. BST Pin Considerations
The minimum input voltage of an LT3692A application is
limited by the minimum operating voltage (typically 2.8V)
and by the maximum duty cycle as outlined above. For
proper start-up, the minimum input voltage is also limited
by the boost circuit. If the input voltage is ramped slowly,
or the LT3692A is turned on with its SS pin when the
output is already in regulation, then the boost capacitor
may not be fully charged. Because the boost capacitor is
charged with the energy stored in the inductor, the circuit
will rely on some minimum load current to get the boost
circuit running properly. This minimum load will depend
on input and output voltages, and on the arrangement of
the boost circuit. The Typical Performance Characteristics
section shows plots of the minimum load current to start
and to run as a function of input voltage for 3.3V outputs.
In many cases the discharged output capacitor will present
a load to the switcher which will allow it to start. The plots
show the worst-case situation where VIN is ramping very
slowly. Use a Schottky diode for the lowest start-up voltage.
Outputs Greater Than 6V
For outputs greater than 6V, add a resistor of 1k to 2.5k
across the inductor to damp the discontinuous ringing of
the SW node, preventing unintended SW current. The 12V
output circuit in the Typical Applications section shows
the location of this resistor.
Frequency Compensation
The LT3692A uses current mode control to regulate the
output. This simplifies loop compensation. In particular, the
LT3692A does not require the ESR of the output capacitor
for stability so you are free to use ceramic capacitors to
achieve low output ripple and small circuit size. Frequency
compensation is provided by the components tied to the
VC pin. Generally a capacitor and a resistor in series to
ground determine loop gain. In addition, there is a lower
value capacitor in parallel. This capacitor is not part of
the loop compensation but is used to filter noise at the
switching frequency.
3692afb
18
LT3692A
Applications Information
Loop compensation determines the stability and transient
performance. Designing the compensation network is a bit
complicated and the best values depend on the application
and in particular the type of output capacitor. A practical
approach is to start with one of the circuits in this data
sheet that is similar to your application and tune the compensation network to optimize the performance. Stability
should then be checked across all operating conditions,
including load current, input voltage and temperature.
The LT1375 data sheet contains a more thorough discussion of loop compensation and describes how to test the
stability using a transient load.
Figure 8 shows an equivalent circuit for the LT3692A control
loop. The error amp is a transconductance amplifier with
finite output impedance. The power section, consisting of
the modulator, power switch and inductor, is modeled as
a transconductance amplifier generating an output current proportional to the voltage at the VC pin. Note that
the output capacitor integrates this current, and that the
capacitor on the VC pin (CC) integrates the error amplifier
output current, resulting in two poles in the loop. In most
cases a zero is required and comes from either the output
capacitor ESR or from a resistor in series with CC.
This simple model works well as long as the value of the
inductor is not too high and the loop crossover frequency
is much lower than the switching frequency. A phase lead
capacitor (CPL) across the feedback divider may improve
the transient response.
Synchronization
The RT/SYNC pin can also be used to synchronize the
regulators to an external clock source. Driving the RT/SYNC
resistor with a clock source triggers the synchronization
detection circuitry. Once synchronization is detected, the
rising edge of SW1 will be synchronized to the rising edge
of the RT/SYNC signal and the rising edge of SW2 synchronized to the falling edge of the RT/SYNC signal (see
Figures 10 and 11). During synchronization, a 0V to 2.4V
square wave with the same frequency and duty cycle as
the synchronization signal is output via the CLKOUT pin
with a typical propagation delay of 250ns. In addition, an
internal AGC loop will adjust slope compensation to avoid
subharmonic oscillation. If the synchronization signal is
halted, the synchronization detection circuitry will timeout
in typically 10µs at which time the LT3692A reverts to the
free-running frequency based on the RT/SYNC pin voltage.
The synchronizing clock signal input to the LT3692A must
have a frequency between 200kHz and 2MHz, a duty cycle
between 20% and 80%, a low state below 0.5V and a high
state above 1.6V. Synchronization signals outside of these
parameters will cause erratic switching behavior. If the
RT/SYNC pin is held above 1.6V at any time, switching
will be disabled.
If the synchronization signal is not present during regulator start-up (for example, the synchronization circuitry
is powered from the regulator output) the RT/SYNC pin
must remain below 1V until the synchronization circuitry
is active for proper start-up operation.
LT3692A
CURRENT MODE
POWER STAGE
gm = 4.8mho
OUTPUT
gm = 400µmho
3.6M
RC
CF
CC
+
–
VC
ERROR
AMP
R1
CPL
ESR
FB
C1
+
0.806V
R2
C1
CERAMIC
TANTALUM
OR
POLYMER
3692a F08
Figure 8. Model for Loop Response
3692afb
19
LT3692A
Applications Information
If the synchronization signal powers up in an undetermined
state (VOL, VOH, Hi-Z), connect the synchronization clock
to the LT3692A as shown in Figure 9. The circuit as shown
will isolate the synchronization signal when the output
voltage is below 90% of the regulated output. The LT3692A
will start up with a switching frequency determined by the
resistor from the RT/SYNC pin to ground.
If the synchronization signal powers up in a low impedance
state (VOL), connect a resistor between the RT/SYNC pin
and the synchronizing clock. The equivalent resistance
seen from the RT/SYNC pin to ground will set the startup frequency.
If the synchronization signal powers up in a high impedance state (Hi-Z), connect a resistor from the RT/SYNC
pin to ground. The equivalent resistance seen from the
RT/SYNC pin to ground will set the start-up frequency.
VOUT1
VCC
LT3692A
PG1
SYNCHRONIZATION
CIRCUITRY
RT/SYNC
CLK
3692a F09
Figure 9. Synchronous Signal Powered from Regulator’s Output
tP
SW1
tP
SW2
tPON
tP
CLKOUT
tDCLKOSW1
tDCLKOSW2
tPON
tP
RT/SYNC
3692a F11
tDRTSYNCH
tDRTSYNCH
Figure 11. Timing Diagram RT/SYNC = 1MHz, Duty Cycle > 50%
Reducing Input Ripple Voltage
Synchronizing the switches to the rising and falling edges
of the synchronization signal provides the unique ability to
reduce input ripple currents in systems where VIN1 and VIN2
are connected to the same supply. Decreasing the input
current ripple reduces the required input capacitance. For
example, the input ripple voltage shown in Figure 12 for
a typical antiphase dual 14.4V to 8.5V and 14.4V to 3.3V
regulator is decreased from a peak of 472mV to 160mV
as shown in Figure 13 by driving the LT3692A with a 71%
duty cycle synchronization signal.
SW1
tP
SW2
SW1
tP/2
tP
INPUT
RIPPLE V
SW2
RT/SYNC
tP
tP/2
3692a F12
Figure 12. Dual 14.4V/8.5V, 14.4V/3.3V with 180° Phase
CLKOUT
tDCLKOSW1
tDCLKOSW2
tP/2
SW1
tP
RT/SYNC
SW2
3692a F10
tDRTSYNC
Figure 10. Timing Diagram RT/SYNC = 1MHz, Duty Cycle = 50%
INPUT
RIPPLE V
RT/SYNC
3692a F13
Figure 13. Dual 14.4V/8.5V, 14.4V/3.3V with 256° Phase
3692afb
20
LT3692A
Applications Information
Shutdown and Undervoltage/Overvoltage Lockout
ramp from 0V to the regulated output whose duration is
given by:
Typically, undervoltage lockout (UVLO) is used in situations where the input supply is current limited, or has a
relatively high source resistance. A switching regulator
draws constant power from the source, so source current increases as source voltage drops. This looks like a
negative resistance load to the source and can cause the
source to current limit or latch low under low source voltage
conditions. UVLO prevents the regulator from operating
at source voltages where these problems might occur.
At power-up, a reset signal sets the soft-start latch and
discharges both SS pins to approximately 0V to ensure
proper start-up. When both SS pins are fully discharged
the latch is reset and the internal 12µA current source
starts to charge the SS pin.
Overvoltage lockout (OVLO) is typically used to shut down
the switching regulator during potentially harmful input
voltage transients.
When the SS pin voltage is below 115mV, the VC pin is
pulled low which disables switching. This allows the SS
pin to be used as an individual shutdown for each channel.
The overvoltage lockout threshold is typically 39V. Each
channel of the LT3692A is forced into shutdown when its
input voltage exceeds 39V, and will survive voltages as
high as 60V. When the input voltage drops back below
39V, the LT3692A goes through a POR cycle and the output
soft-starts from its existing level to its regulation point.
As the SS pin voltage rises above 90mV, the VC pin is released and the output is regulated to the SS voltage. When
the SS pin voltage exceeds the internal 0.806V reference,
the output is regulated to the reference. The SS pin voltage
will continue to rise until it is clamped at typically 2.15V.
Additionally, an internal comparator will force both channels into shutdown below the minimum VIN1 of 2.8V.
This feature can be used to prevent excessive discharge
of battery-operated systems. In addition to the VIN1 undervoltage lockout, both channels will be disabled when
SHDN1 is less than 1.32V.
Programmable UVLO may be implemented using an input
voltage divider and one of the internal comparators (see
the Typical Applications section).
When the SHDN pin is taken above 1.32V, its respective
channel is allowed to operate. When the SHDN pin is
driven below 1.32V, its channel is placed in a low quiescent
current state. There is no hysteresis on the SHDN pins.
Keep the connections from any series resistors to the SHDN
pins short and make sure that the interplane or surface
capacitance to switching nodes is minimized.
Soft-Start
The output of the LT3692A regulates to the lowest voltage
present at either the SS pin or an internal 0.806V reference.
A capacitor from the SS pin to ground is charged by an
internal 12µA current source resulting in a linear output
tRAMP =
CSS • 0.806V
12µA
In the event of a VIN1 undervoltage lockout, the soft-start latch
is set for both channels, triggering a full start-up sequence. If
a channel’s SHDN pin is driven below 1.32V, its overvoltage
lockout is enabled, or the internal die temperature for its
power switch exceeds its maximum rating during normal
operation, the soft-start latch is set for that channel.
In addition, if the load exceeds the maximum output switch
current, the output will start to drop causing the VC pin
clamp to be activated. As long as the VC pin is clamped,
the SS pin will be discharged. As a result, the output will
be regulated to the highest voltage that the maximum
output current can support. For example, if a 6V output is
loaded by 1Ω the SS pin will drop to 0.64V, regulating the
output at 4.8V (4.8A • 1Ω). Once the overload condition
is removed, the output will soft start from the temporary
voltage level to the normal regulation point.
Since the SS pin is clamped at typically 2.15V and has to
discharge to 0.806V before taking control of regulation,
momentary overload conditions will be tolerated without
a soft-start recovery. The typical time before the SS pin
takes control is:
tSS(CONTROL) =
CSS • 1.2V
1.4mA
3692afb
21
LT3692A
Applications Information
Open-Collector Comparators
The CMPO pin is the open-collector output of an internal
comparator. The comparator compares the CMPI pin voltage to 90% of the reference voltage (0.72V) with 60mV
of hysteresis.
The CMPO pin has a typical sink capability of 300µA when
the CMPI pin is below the threshold and can withstand 40V
when the threshold is exceeded. The CMPO pin is active
(sink capability is reduced in shutdown and undervoltage
lockout mode) as long as the VIN1 pin voltage exceeds
typically 2.8V.
The comparators can be used to monitor input and output
voltages as well as die temperature. See the Typical Applications circuit collection for examples.
Output Tracking/Sequencing
Complex output tracking and sequencing between channels
can be implemented using the LT3692A’s SS and CMPO
pins. Figure 14 shows several configurations for output
tracking/sequencing for a 3.3V and 1.8V application.
Independent soft-start for each channel is shown in Figure 16a. The output ramp time for each channel is set by
the soft-start capacitor as described in the soft-start section.
Ratiometric tracking is achieved in Figure 14b by connecting both SS pins together. In this configuration, the
SS pin source current is doubled (24µA) which must be
taken into account when calculating the output rise time.
By connecting a feedback network from VOUT1 to the SS2
pin with the same ratio that sets VOUT2 voltage, absolute
tracking shown in Figure 14c is implemented. The minimum value of the top feedback resistor (R1) should be set
such that the SS pin can be driven all the way to ground
with 1.4mA of sink current when VOUT1 is at its regulated
voltage. In addition, a small VOUT2 voltage offset will be
present due to the SS2 12µA source current. This offset
can be corrected for by slightly reducing the value of R2.
Figure 14d illustrates output sequencing. When VOUT1 is
within 10% of its regulated voltage, CMPO1 releases the
SS2 soft-start pin allowing VOUT2 to soft-start. In this case
CMPO1 will be pulled up to 2V by the SS pin. If a greater
voltage is needed for CMPO1 logic, a pull-up resistor to
VOUT1 can be used. This will decrease the soft-start ramp
time and increase tolerance to momentary shorts.
If precise output ramp up and down is required, drive the
SS pins as shown in Figure 14e. The minimum value of
resistor (R3) should be set such that the SS pin can be
driven all the way to ground with 1.4mA of sink current
during power-up and fault conditions.
Application Optimization
In multiple channel applications requiring large VIN to
VOUT ratios, the maximum frequency and resulting inductor size is determined by the channel with the largest
ratio. The LT3692A’s multi-frequency operation allows the
user to minimize component size for each channel while
maintaining constant frequency operation. The circuit in
Figure 15 illustrates this approach. A 2-stage step-down
approach coupled with multi-frequency operation will
further reduce external component size by allowing an
increase in frequency for the channel with the lower VIN
to VOUT ratio. The drawback to this approach is that the
output power capability for the first stage is determined by
the output power drawn from the second stage. The dual
step-down application in Figure 16 steps down the input
voltage (VIN1) to the highest output voltage then uses that
voltage to power the second output (VIN2). VOUT1 must be
able to provide enough current for its output plus VOUT2
maximum load. Note that the VOUT1 voltage must be above
VIN2’s minimum input voltage as specified in the Electrical
Characteristics (typically 2.8V) when the second channel
starts to switch. Delaying channel 2 can be accomplished
by either independent soft-start capacitors or sequencing
with the CMP01 output.
For example, assume a maximum input of 36V:
VIN = 36V, VOUT1 = 3.3V at 2A and VOUT2 = 1.2V at 1A.
Frequency (Hz) =
L=
VOUT + VD
1
•
VIN – VSW + VD tON(MIN)
( VIN – VOUT ) • VOUT
VIN • f
3692afb
22
LT3692A
Applications Information
Independent Start-Up
Ratiometric Start-Up
Absolute Start-Up
VOUT1
0.5V/DIV
VOUT1
0.5V/DIV
PG1
VOUT2
0.5V/DIV
VOUT2
0.5V/DIV
5ms/DIV
LT3692A
FB1
CMPI1
0.72V
+
–
0.1µF
CMPO1
12µA
0.72V
+
–
FB1
CMPI1
2.5V
12µA
0.72V
SS1
2.5V
PG2
12µA
0.72V
SS2
12µA
PG1
0.72V
+
–
R4
FB2
CMPI2
2.5V
PG2
12µA
0.72V
SS2
R8
0.22µF
(14a)
PG1
VOUT2
R6
R5
CMPO2
R3
R2
CMPO1
+
–
0.1µF
R4
FB2
CMPI2
FB1
CMPI1
2.5V
VOUT2
R5
CMPO2
R1
SS1
R6
VOUT1
R3
R2
CMPO1
+
–
0.1µF
FB2
CMPI2
SS2
R1
PG1
R4
LT3692A
VOUT1
R3
R2
VOUT2
2.5V
10ms/DIV
LT3692A
R1
SS1
PG2
10ms/DIV
VOUT1
2.5V
VOUT2
0.5V/DIV
PG2
PG2
12µA
VOUT1
0.5V/DIV
PG1
PG1
CMPO2
+
–
R6
R5
PG2
R7
(14b)
(14c)
Output Sequencing
Controlled Power Up and Down
VOUT1
0.5V/DIV
VOUT1
0.5V/DIV
PG1/PG2
VOUT2
0.5V/DIV
VOUT2
0.5V/DIV
PG1
SS1/2
PG2
10ms/DIV
10ms/DIV
LT3692A
LT3692A
VOUT1
VOUT1
R1
FB1
CMPI1
2.5V
12µA
0.72V
SS1
+
–
0.1µF
R1
R2
2.5V
CMPO1
R4
12µA
SS2
0.72V
+
–
CMPO2
0.72V
SS1
+
–
VOUT2
2.5V
12µA
PG1
R5
FB2
CMPI2
FB1
CMPI1
+
–
R2
CMPO1
PG1
VOUT2
R4
R6
R5
FB2
CMPI2
2.5V
PG2
R3
12µA
SS2
0.72V
+
–
0.22µF
R6
R5
CMPO2
PG2
3692a F14
(14d)
(14e)
Figure 14. SS Pin Configurations
3692afb
23
LT3692A
Applications Information
VIN1
5.5V TO 36V
4.7µF
4.7µF
VIN2
VIN1
SHDN1
BST1
VOUT1
1.2V
3A
300kHz
4.7µH
0.47µF
100k
100µF
×3 8.06k
SHDN2
BST2
SW1
SW2
IND1
IND2
100pF
4.02k
FB1
CMPI2
CMPO1
CMPO2
7.50k
ILIM2
VC2
RT/SYNC
DIV
33pF
15.8k
61.9k
47µF
8.06k
VOUT2
3.3V
2A
600kHz
100k
PG2
SS2
ILIM1
VC1
820pF
24.9k
FB2
CMPI1
SS1
49.9k
0.47µF
LT3692A
VOUT2
VOUT1
PG1
0.1µF
4.7µH
CLKOUT
GND
TJ
ILIM1
CLOCKOUT
600kHz
680pF
33pF
10nF
0.1µF
13.0k
3692a F15
Figure 15. 3.3V and 1.2V Dual Step-Down Multi-Frequency Converter
3692afb
24
LT3692A
Applications Information
VIN1
5.5V TO 36V
4.7µF
VIN2
VIN1
SHDN1
BST1
SHDN2
BST2
0.22µF
VOUT1
3.3V
2.5A
550kHz
100k
47µF
4.7µH
24.9k
IND1
IND2
LT3692A
VOUT2
VOUT1
FB1
8.06k
PG
33pF
CMPI2
CMPO1
CMPO2
100k
SS2
ILIM2
VC2
RT/SYNC
680pF
13k
DIV
68.1k
102k
0.5µH
4.02k
FB2
CMPI1
SS1
ILIM1
VC1
0.1µF
0.1µF
SW2
SW1
CLKOUT
GND
TJ
FB1
100pF
VOUT2
1.2V
1A
47µF 2.2MHz
8.06k
CLKOUT
2.2MHz
10nF
220pF
0.1µF
22pF
40.2k
33.2k
3692a F16
Figure 16. 3.3V and 1.2V 2-Stage Dual Step-Down Multi-Frequency Converter
3692afb
25
LT3692A
Applications Information
Single Step-Down:
Frequency (Hz) =
L1 =
L2 =
1.2 + 0.6
35V – 0.4 + 0.6
( 36V – 3.3 ) • 3.3
•
1
140ns
≅ 350kHz
≥ 8.5µH
36V • 350kHz
( 36V – 1.2 ) • 1.2
≥ 3.3µH
36V • 350kHz
system can tolerate a few mA in this state. If you ground
the SHDN pin, the SW pin current will drop to essentially
zero. However, if the VIN pin is grounded while the output
is held high, then parasitic diodes inside the LT3692A can
pull large currents from the output through the SW pin
and the VIN1/2 pin. Figure 17 shows a circuit that will run
only when the input voltage is present and that protects
against a shorted or reversed input.
PARASITIC DIODE
2-Stage Step-Down:
Frequency (Hz) =
L1 =
L2 =
D4
3.3 + 0.6
36V – 0.4 + 0.6
( 36V – 3.3 ) • 3.3
36V • 750kHz
( 3.3 – 1.2 ) • 1.2
3.3 • 750kHz
•
1
140ns
VIN1/2
≅ 750kHz
≥ 1.0µH
RDIV = 100k, FREQ1 = 550kHz, FREQ2 = 2200kHz.
L2 =
SW
VOUT1/2
LT3692A
≥ 4.0µH
2-Stage Step-Down Multi-Frequency:
L1=
VIN
3692a F17
Figure 17. Diode D4 Prevents a Shorted Input from Discharging a
Backup Battery Tied to the Output
VIN LT3692A SW
GND
(36V – 3.3) • 3.3 ≥ 5.4µH
36V • 550kHz
(3.3 – 1.2) • 1.2 ≥ 0.47µH
3.3 • 2200K Hz
In addition, RILIM2 = 33.2k reduces the peak current limit
on channel 2 to 2A, which reduces inductor size and catch
diode requirements.
(18a)
VIN LT3692A SW
GND
(18b)
Shorted and Reverse Input Protection
If the inductor is chosen so that it won’t saturate excessively,
an LT3692A step-down regulator will tolerate a shorted
output. There is another situation to consider in systems
where the output will be held high when the input to the
LT3692A is absent. This may occur in battery charging
applications or in battery back-up systems where a battery
or some other supply is diode OR-ed with the LT3692A’s
output. If the VIN1/2 pin is allowed to float and the SHDN
pin is held high (either by a logic signal or because it is
tied to VIN), then the LT3692A’s internal circuitry will pull
its quiescent current through its SW pin. This is fine if your
VIN LT3692A SW
GND
(18c)
3692a F18
Figure 18. Subtracting the Current When the Switch Is On (18a)
from the Current When the Switch Is Off (18b) Reveals the Path of
the High Frequency Switching Current (18c). Keep this Loop Small.
The Voltage on the SW and BST Traces Will Also Be Switched; Keep
These Traces as Short as Possible. Finally, Make Sure the Circuit
Is Shielded with a Local Ground Plane
3692afb
26
LT3692A
Applications Information
PCB Layout
For proper operation and minimum EMI, care must be
taken during printed circuit board (PCB) layout. Figure 18
shows the high di/dt paths in the buck regulator circuit.
Note that large switched currents flow in the power switch,
the catch diode and the input capacitor. The loop formed
by these components should be as small as possible.
These components, along with the inductor and output
capacitor, should be placed on the same side of the circuit board and their connections should be made on that
layer. Place a local, unbroken ground plane below these
components, and tie this ground plane to system ground
at one location, ideally at the ground terminal of the output capacitor C2. Route all small signal analog returns
to the ground connection at the bottom of the package.
Additionally, the SW and BST traces should be kept as
short as possible.
Thermal Considerations
The PCB must also provide heat sinking to keep the LT3692A
cool. The exposed metal on the bottom of the package
must be soldered to a ground plane. This ground should
be tied to other copper layers below with thermal vias;
these layers will spread the heat dissipated by the LT3692A.
DC1403A TSSOP LAYOUT
Place additional vias near the catch diodes. Adding more
copper to the top and bottom layers and tying this copper
to the internal planes with vias can further reduce thermal
resistance. The topside metal and component outlines
in Figure 19 illustrate proper component placement and
trace routing.
The LT3692A’s powerful 3.8A switches allow the converter
to source large output currents. Depending on the converter’s operating conditions, the resulting internal power
dissipation can raise the junction temperature beyond
its maximum rating. Operating conditions include input
voltages, output voltages, switching frequencies, output
currents, and the ambient environmental temperature,
etc. An estimation of the junction temperature rise above
ambient temperature helps determine whether a given
design may exceed the maximum junction ratings for
specific operating conditions. However, temperature rise
depends on PCB design and the proximity to other heat
sources. The final converter design must be evaluated
on the bench.
An estimation of the junction temperature rise begins by
determining which circuit components dissipate power.
In order to simplify the power loss estimation, only the
inductors, catch diodes, and the LT3692A will be considered
QFN LAYOUT
Figure 19. PCB Top Layer and Component Placement for TSSOP and QFN Packages
3692a F19
3692afb
27
LT3692A
Applications Information
as heat sources. After the operating conditions have been
determined, the individual power losses are calculated by:

V 
PowerD1,2 =  1− OUT  • IOUT • VFD

VIN 
PowerIND1,2 = RIND • IOUT2
PowerCH1,2
•VIN +
V
= 0.1• OUT • IOUT2 + 2 • 10 –3
VIN
IOUT • VOUT • VBOOST
40 • VIN
+
 VIN IOUT 
VIN • IOUT • FSW • 10−6 • 
+
0.3 
 3
where:
FSW = Switching Frequency in kHz
RIND = Inductor Resis tance
VFD = Catch Diode Forward Voltage Drop
VBOOST = Switch Boost Voltage
For the LT3692A demo board (see Figure 19) using the
TSSOP package, the estimated junction temperature rise
above ambient temperature is found by:
TRISETSSOP ≈ 10 • (PowerD1 + PowerD2 ) +
12.3 • (PowerIND1 + Power IND2) + 17.5 •
(PowerCH1 + PowerCH2 )
The estimated junction temperature rise above ambient
for the LT3692A QFN layout (see Figure 19) is:
TRISEQFN ≈ 8.5 • (Power D1+ Power D2) +
13 • (Power IND1+ Power IND2) + 23 •
(PowerCH1 + PowerCH2 )
For example, the typical application circuits listed in Table 4
are used to calculate the individual power loss contributions in Table 5. Table 6 shows the estimated power loss
and junction temperature rise above ambient temperature.
Note that the larger TSSOP package demonstrates better
thermal performance than the compact QFN package on
the LT3692A demo circuit boards. For LT3692A applications that favor thermal performance, the TSSOP package
is the preferred package option.
Table 4. LT3692A Operating Conditions
FSW
VOUT1
VIN
(V)
(kHz)
(V)
30
300/600
1.2
12
1000
3.3
24
500
5
12
500
5
IOUT1
(A)
2
2.5
2
3
VOUT2
(V)
3.3
3.3
3.3
3.3
IOUT2
(A)
2
2.5
2
3
Table 5. LT3692A Power Loss Contributions
PD1
PD2
PL1
PL2
(W)
(W)
(W)
(W)
0.86
0.80
0.24
0.24
0.82
0.82
0.25
0.25
0.71
0.78
0.24
0.24
0.79
0.98
0.54
0.54
PCH1
(W)
0.38
0.62
0.54
0.81
PCH2
(W)
0.72
0.62
0.48
0.59
Table 6. Estimated System Power Loss and IC Temperature Rise
TRISE TSSOP (°C)
TRISE QFN (°C)
PLOSS (W)
CALCULATED MEASURED CALCULATED MEASURED CALCULATED MEASURED
3.2
3.4
3.0
4.2
3.2
3.5
3.1
4.7
41.9
44.3
38.5
55.4
44.9
48.8
35.3
52.0
45.8
49
42.2
61.2
49.1
54.8
42.3
63
The power loss and temperature rise equations provided
in the Thermal Considerations section serve as a good
starting point for estimating the junction temperature
rise. However, the LT3692A is a very versatile converter.
The combination of independent input voltages, output
voltages, output currents, switching frequencies, and
package selections for the LT3692A dictate that no power
loss estimation scheme can accommodate every possible
operating condition. As such, it is absolutely necessary to
evaluate a converter’s performance at the bench.
The power dissipation in the other power components such
as boost diodes, input and output capacitors, inductor
core loss, and trace resistances cause additional copper
heating and can further increase what the IC sees as ambient temperature. See the LT1767 data sheet’s Thermal
Considerations section.
3692afb
28
LT3692A
Applications Information
Die Temperature and Thermal Shutdown
Generating a Negative Regulated Voltage
The LT3692A TJ pin outputs a voltage proportional to the
internal junction temperature. The TJ pin typically outputs
250mV for 25°C and has a slope of 10mV/°C. Without the
aid of external circuitry, the TJ pin output is valid from 20°C
to 150°C (200mV to 1.5V) with a maximum load of 100µA.
The simple charge pump circuit in Figure 21 uses the
CLKOUT pin output to generate a negative voltage, eliminating the need for an external regulated supply. Surface
mount capacitors and dual-package Schottky diodes
minimize the board area needed to implement the negative voltage supply.
Full Temperature Range Measurement
To extend the operating temperature range of the TJ output below 20°C, connect a resistor from the TJ pin to a
negative supply as shown in Figure 20. The negative rail
voltage and TJ pin resistor may be calculated using the
following equations:
VNEG
2 • TEMP(MIN)°C
≤
100
R1≤
VNEG
33µA
where:
330pF
D4
CLKOUT
GND
0.1µF
D3
3692 F21
Figure 21. Circuit to Generate the Negative Voltage Rail to
Extend the TJ Pin Operating Range
VNEG = Regulated negative voltage supply.
For example:
TEMP(MIN)°C = –40°C
VNEG ≤ –0.8V
VNEG = –1, R1 ≤ |VNEG|/33µA = 30.2kΩ
TJ
LT3692A
30k
D3, D4: ZETEX BAT54S
TEMP(MIN)°C is the minimum temperature where a
valid TJ pin output is required.
LT3692A
TJ
As a safeguard, the LT3692A has an additional thermal
shutdown threshold set at a typical value of 163°C for each
channel. Each time the threshold is exceeded, a power-on
sequence for that channel will be initiated. The sequence
will then repeat until the thermal overload is removed.
It should be noted that the TJ pin voltage represents
a steady-state temperature and should not be used to
guarantee that maximum junction temperatures are
not exceeded. Instantaneous power along with thermal
gradients and time constants may cause portions of the
die to exceed maximum ratings and thermal shutdown
thresholds. Be sure to calculate die temperature rise for
steady state (>1Min) as well as impulse conditions.
R1
VNEG
GND
+
3692 F20
Figure 20. Circuit to Extend the TJ Pin Operating Range
3692afb
29
LT3692A
Applications Information
CLKOUT Capacitive Loading
A minor drawback to generating a negative rail from the
CLKOUT pin is that the charge pump adds capacitance to
the CLKOUT pin, resulting in an output synchronization
clock signal phase delay. Figures 22 and 23 show the impact of capacitive loading on the CLKOUT signal rise and
fall times. Note that a typical 10:1 150MHz oscilloscope
probe contributes significant capacitance to the CLKOUT
node, necessitating a low capacitance probe for accurate
measurements. Applications requiring CLKOUT to generate
the negative supply voltage and provide the synchronization clock to other regulators may benefit from buffering
CLKOUT prior to the charge pump circuitry.
CHARGE PUMP
SCOPE PROBE: 15pF
SYNCHRONIZED LT3692A
RT/SYNC PIN
FET PROBE: 2pF
500mV/DIV
40ns/DIV
FREQUENCY: 1.000MHz
3692a F22
Figure 22. CLKOUT Rise Time
Other Linear Technology Publications
Application Notes 19, 35 and 44 contain more detailed
descriptions and design information for buck regulators
and other switching regulators. The LT1376 data sheet
has a more extensive discussion of output ripple, loop
compensation and stability testing. Design Note 100
shows how to generate a dual (+ and –) output supply
using a buck regulator.
SCOPE PROBE: 15pF
CHARGE PUMP
SYNCHRONIZED
LT3692A RT/SYNC PIN
500mV/DIV
FET PROBE: 2pF
20ns/DIV
FREQUENCY: 1.000MHz
3692a F23
Figure 23. CLKOUT Fall Time
3692afb
30
VIN
6V TO 36V
0.1µF
VOUT1
5V 1.5A
500kHz
100k
47µF
4.7µF
33pF
8.06k
680pF
10.0k
100pF
0.47µF
61.9k
42.2k
6.8µH
VIN2
IND2
SW2
SHDN2
BST2
102k
DIV
GND
TJ
CLKOUT
ILIM1
VC1
RT/SYNC
SS2
ILIM2
VC2
SS1
CMPO2
CMPO1
FB2
CMPI2
CMPI1
FB1
LT3692A
VOUT2
VOUT1
IND1
SW1
SHDN1
BST1
VIN1
10nF
16.9k
1.5µH
33pF
330pF
11.0k
8.06k
100pF
0.1µF
49.9k
PG
100k
8.06k
10k
CLOCKOUT
2MHz
22µF
VOUT2
2.5V 1A
2MHz
8.06k
4.02k
VOUT3
1.2V 1A
1MHz
49.9k
33pF
8.06k
100µF
0.1µF
4.02k
9.76k
470pF
100pF
1.5µH
1µF
VIN2
IND2
SW2
SHDN2
BST2
61.9k
DIV
FB2
ILIM2
VC2
SS2
CMPO2
CMPI2
TJ
CLKOUT
GND
RT/SYNC
ILIM1
VC1
SS1
CMPO1
CMPI1
FB1
LT3692A
VOUT2
VOUT1
IND1
SW1
SHDN1
BST1
VIN1
Quad Output 5V, 2.5V, 1.8V and 1.2V Multi-Frequency Synchronized, 2-Stage Converter
with Output Sequencing, Absolute Tracking and Current Limiting
10nF
10k
1.5µH
15.0k
220pF
100pF
0.1µF
8.06k
33pF
1µF
3692a TA02
49.9k
VOUT4
1.8V 1A
47µF 2MHz
LT3692A
Typical Applications
3692afb
31
LT3692A
TYPICAL APPLICATIONS
3.3V and 1.8V 2-Stage Dual Step-Down Multi-Frequency Converter
VIN
5.5V TO 36V
4.7µF
VIN2
VIN1
SHDN1
BST1
8.2µH
0.47µF
VOUT1
3.3V 2.5A
400kHz 100µF
SHDN2
BST2
SW1
SW2
IND1
IND2
100pF
24.9k
FB1
FB2
CMPI1
CMPI2
CMPO1
CMPO2
SS1
DIV
33pF
16.5k
ILIM2
VC2
RT/SYNC
470pF
47.5k
102k
10k
47µF
100pF
100k
VOUT2
1.8V
1A
1600kHz
8.06k
PG
SS2
ILIM1
VC1
100k
0.22µF
LT3692A
VOUT2
VOUT1
8.06k
0.1µF
1µH
CLKOUT
GND
TJ
0.1µF
CLOCKOUT
1600kHz
330pF
33pF
10nF
36.5k
40.2k
3692a TA03
3692afb
32
LT3692A
TYPICAL APPLICATIONS
12V to 3.3V and 2.5V Converter with Start-Up Current Limiting
VIN
12V
4.7µF
4.7µF
VIN2
VIN1
SHDN1
BST1
2.2µH
0.22µF
VOUT1
2.5V
3A
1MHz
SHDN2
BST2
SW1
SW2
IND1
IND2
0.22µF
LT3692A
VOUT2
VOUT1
47µF
8.06k
100pF
16.9k
FB1
FB2
CMPI1
CMPI2
CMPO1
CMPO2
ILIM2
VC2
ILIM1
VC1
0.1µF
RT/SYNC
330pF
DIV
33pF
0.1µF
21.0k
28.0k
24.9k
100pF
8.06k
47µF
VOUT2
3.3V
3A
1MHz
SS2
SS1
120k
2.2µH
CLKOUT
GND
TJ
CLOCKOUT
1MHz
33pF
0.1µF
330pF
10nF
24.9k
0.1µF
120k
3692a TA04
3692afb
33
LT3692A
TYPICAL APPLICATIONS
3.3V/5A Single Output with UVLO/OVLO and Power Good
VIN
5.5V TO 18V
60V TRANSIENT
4.7µF
×2
13k
174k
7.15k
37.4k
VIN2
VIN1
SHDN1
SHDN2
BST1
CMPI2
CMPO2
51.1k
ILIM1
ILIM2
820pF
33pF
CLOCKOUT
1MHz
SW1
IND1
LT3692A
VOUT1
SS1
VOUT2
SS2
VC1
BST2
SW2
VC2
10nF
0.1µF
CLKOUT
20k
28k
DIV
47µF
×2
GND
FB1
CMPI1
FB2
CMPO1
VOUT
3.3V
5A
2MHz EFFECTIVE RIPPLE
0.22µF
3.3µH
IND2
RT/SYNC
TJ
Q1
2N3904
0.22µF
3.3µH
24.9k
8.06k
100k
PG
3692a TA05
3692afb
34
LT3692A
TYPICAL APPLICATIONS
Power Supply Dual Input Single 3.3V/4A Output Step-Down Converter
VIN1
12V
4.7µF
47.5k
13k
2.2µF
VIN2
VIN1
SHDN1
SHDN2
BST1
CMPO1
CMPO2
SW1
VIN2
5V
2A MAX
SHDN1
0.22µF
2.2µH
IND1
LT3692A
SS2
VOUT1
SS1
0.1µF
64.9k
36.5k
33pF
680pF
21.0k
CLOCKOUT
2MHz
61.9k
61.9k
ILIM1
VOUT2
ILIM2
VC1
BST2
SW2
VC2
0.22µF
2.2µH
IND2
CLKOUT
RT/SYNC
DIV
FB1
CMPI1
FB2
TJ
CMPI2
10nF
47µF
×2
GND
VOUT
3.3V
4A
24.9k
8.06k
3692a TA06
3692afb
35
LT3692A
TYPICAL APPLICATIONS
5V and 1.8V Dual 2-Stage Converter
VIN1
6V TO 36V
4.7µF
VIN2
VIN1
SHDN1
BST1
4.7µH
0.22µF
VOUT1
5V
1A
1MHz
SHDN2
BST2
SW1
SW2
IND1
IND2
1µH
0.22µF
LT3692A
VOUT2
VOUT1
22µF
100k
42.2k
8.06k
PG
FB1
CMPI2
CMPO1
CMPO2
SS1
0.1µF
49.9k
10k
ILIM2
VC2
RT/SYNC
DIV
33pF
61.9k
61.9k
FB1
47µF
100pF
8.06k
SS2
ILIM1
VC1
680pF
10k
FB2
CMPI1
VOUT2
1.8V
1A
2MHz
CLKOUT
GND
TJ
ILIM1
CLOCKOUT
2MHz
33pF
0.1µF
330pF
10nF
39.2k
3692a TA07
3692afb
36
100k
0.1µF
PG1
VOUT1
12V 0.5A
1MHz
37.6k
33pF
470pF
8.06k
22µF
0.47µF
VIN
15V TO 36V
28k
113k
1k
10µH
OFF ON
4.7µF
IND2
SW2
SHDN2
BST2
VIN2
FB2
DIV
GND
TJ
CLKOUT
ILIM2
VC2
ILIM1
VC1
RT/SYNC
SS2
CMPO2
CMPI2
SS1
CMPO1
CMPI1
FB1
LT3692A
VOUT2
VOUT1
IND1
SW1
SHDN1
BST1
VIN1
24.9k
10nF
FB1
3.3µH
SHDN1
33pF
16.0k
330pF
8.06k
0.22µF
100k
47µF
133k
0.1µF
0.1µF
SS2
VOUT3
1.2V 3A
1MHz
OUT2
MOD
GND
SET
OUT1
U1
LTC6908-1
V+
VOUT2
3.3V 2A
1MHz
VOUT2
100k
8.06k
100µF
0.22µF
33pF
150pF
4.99k
1nF
SS2
4.02k
1.5µH
SHDN1
1µF
IND2
SW2
SHDN2
BST2
VIN2
GND
TJ
CLKOUT
DIV
RT/SYNC
FB2
CMPI2
CMPO2
SS2
ILIM2
VC2
CMPI1
CMPO1
SS1
ILIM1
VC1
FB1
LT3692A
VOUT2
VOUT1
IND1
SW1
SHDN1
BST1
VIN1
12V, 3.3V, 2.5V, 1.2V Quad Output with External Synchronization, Output Sequencing and Tracking Application
10nF
SS2
16.9k
2.2µH
SHDN1
33pF
8.06k
VOUT2
3692a TA08
100k
47µF
VOUT4
2.5V 3A
1MHz
330pF
11.2k
100pF
0.22µF
1µF
LT3692A
TYPICAL APPLICATIONS
3692afb
37
LT3692A
TYPICAL APPLICATIONS
5V, 3.3V, 2.5V, 1.8V Synchronized Quad Output
VOUT1
5V
1A
2.2µF
SVIN
PVIN2
PVIN
DDR
4.7µF
×2
RUN LT3612
MODE
RT
VIN2
VIN1
SHDN1
BST1
6.8µH
0.22µF
100pF
42.2k
8.06k
SW1
SW2
IND1
IND2
FB1
FB2
CMPI1
CMPI2
CMPO1
SS1
CMPO2
SS2
ILIM2
VC2
ILIM1
VC1
0.1µF
RT/SYNC
330pF
DIV
33pF
60.4k
24.9k
16k
270k
FB
VOUT2
3.3V
100µF 2A
ITH
TRACK/SS
SGND
PGND
SVIN
PVIN2
60.4k
SHDN2
BST2
6.8µH
2.2µF
0.22µF
LT3692A
VOUT2
VOUT1
47µF
3.3µH
SW
PGOOD
VIN1
7V TO 36V
TJ
0.1µF
RUN LT3612
100k
ILIM1
VC1
MODE
100°C
TEMP FLAG
SS1
RT
3.3µH
SW
PGOOD
47µF
FB1
CLKOUT
GND
PVIN
DDR
191k
FB
VOUT3
2.5V
100µF 2A
ITH
TRACK/SS
SGND
PGND
SVIN
PVIN2
60.4k
CLOCKOUT
600kHz
2.2µF
28k
73.2k
R14
49.9k
PVIN
DDR
PGOOD
RUN LT3612
MODE
RT
SGND
3.3µH
SW
121k
FB
VOUT4
1.8V
100µF 2A
ITH
TRACK/SS
60.4k
PGND
0.1µF
3692 TA09
3692afb
38
LT3692A
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
FE Package
38-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1772 Rev C)
Exposed Pad Variation AA
4.75 REF
38
9.60 – 9.80*
(.378 – .386)
4.75 REF
(.187)
20
6.60 ±0.10
4.50 REF
2.74 REF
SEE NOTE 4
6.40
2.74
REF (.252)
(.108)
BSC
0.315 ±0.05
1.05 ±0.10
0.50 BSC
RECOMMENDED SOLDER PAD LAYOUT
4.30 – 4.50*
(.169 – .177)
0.09 – 0.20
(.0035 – .0079)
0.50 – 0.75
(.020 – .030)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
2. DIMENSIONS ARE IN MILLIMETERS
(INCHES)
3. DRAWING NOT TO SCALE
1
0.25
REF
19
1.20
(.047)
MAX
0° – 8°
0.50
(.0196)
BSC
0.17 – 0.27
(.0067 – .0106)
TYP
0.05 – 0.15
(.002 – .006)
FE38 (AA) TSSOP REV C 0910
4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
3692afb
39
LT3692A
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
UH Package
32-Lead Plastic QFN (5mm × 5mm)
(Reference LTC DWG # 05-08-1693 Rev D)
0.70 ±0.05
5.50 ±0.05
4.10 ±0.05
3.50 REF
(4 SIDES)
3.45 ± 0.05
3.45 ± 0.05
PACKAGE OUTLINE
0.25 ± 0.05
0.50 BSC
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 ± 0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
0.75 ± 0.05
R = 0.05
TYP
0.00 – 0.05
R = 0.115
TYP
PIN 1 NOTCH R = 0.30 TYP
OR 0.35 × 45° CHAMFER
31 32
0.40 ± 0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
3.50 REF
(4-SIDES)
3.45 ± 0.10
3.45 ± 0.10
(UH32) QFN 0406 REV D
0.200 REF
NOTE:
1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE
M0-220 VARIATION WHHD-(X) (TO BE APPROVED)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
0.25 ± 0.05
0.50 BSC
3692afb
40
LT3692A
Revision History
REV
DATE
DESCRIPTION
PAGE NUMBER
A
9/11
Added H-grade
2 to 4
B
4/12
Clarified the synchronization maximum frequency and Typical Application.
1
Clarified the Electrical Characteristics table.
4
Clarified the DIV Voltage Threshold vs Temperature graph.
7
Replaced 90mV with 100mV.
12
Clarified Table 1.
13
Replaced DIV resistor values in the applications schematics.
25, 31, 32
3692afb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
41
LT3692A
Typical Application
FMEA Fault Tolerant 3.3V/2A and 5V/2A Dual Converter
VIN1
6V TO 36V
(60V TRANSIENT)
4.7µF
SHDN2
6.8µH
0.22µF
VOUT1
5V
2A
500kHz
VIN1
SHDN1
BST1
4.7µF
100k
VIN2
SHDN2
BST2
SW1
SW2
IND1
IND2
5.6µH
0.22µF
VOUT2
3.3V
2A
500kHz
LT3692A
VOUT2
VOUT1
4.22k
47µF
249k
806Ω
PG1
SS2
ILIM2
FB1
CMPI2
CMPO1
CMPO2
SS1
820pF
12.7k
10nF
ILIM1
VC1
DIV
100µF
806Ω
249k
PG2
SS2
ILIM2
VC2
RT/SYNC
33pF
2.49k
FB2
CMPI1
CLKOUT
GND
TJ
CLOCKOUT
500kHz
13.0k
10nF
680pF
15.4k
33pF
22nF
49.9k
3692a TA10
Related Parts
PART NUMBER
DESCRIPTION
LT3692
36V with Transient Protection to 60V, Dual 3.5A, 2.5MHz, High Efficiency VIN = 3V to 36V, Transients to 60V, VOUT(MIN) = 0.8V,
IQ = 4mA, ISD <10µA, 5mm × 5mm QFN-32
Step-Down DC/DC Converter
COMMENTS
LT3507
36V, Triple 2.4A, 1.4A and 1.4A (IOUT), 2.5MHz, High Efficiency
Step-Down DC/DC Converter with LDO Controller
VIN = 4V to 36V, VOUT(MIN) = 0.8V, IQ = 7mA, ISD = 1µA,
5mm × 7mm QFN-38
LT3508
36V with Transient Protection to 40V, Dual 1.4A (IOUT), 3MHz,
High Efficiency Step-Down DC/DC Converter
VIN = 3.7V to 37V, VOUT(MIN) = 0.8V, IQ = 4.6mA, ISD = 1µA,
4mm × 4mm QFN-24, TSSOP-16E
LT3680
36V, 3A, 2.4MHz High Efficiency Micropower Step-Down DC/DC
Converter
VIN = 3.6V to 36V, VOUT(MIN) = 0.8V, IQ = 75µA, ISD < 1µA,
3mm × 3mm DFN-10, MSOP-10E
LT3693
36V, 3A, 2.4MHz High Efficiency Step-Down DC/DC Converter
VIN = 3.6V to 36V, VOUT(MIN) = 0.8V, IQ = 1.3mA, ISD < 1µA,
3mm × 3mm DFN-10, MSOP-10E
LT3480
36V with Transient Protection to 60V, 2A (IOUT), 2.4MHz, High Efficiency
Step-Down DC/DC Converter with Burst Mode® Operation
VIN = 3.6V to 38V, Transients to 60V, VOUT(MIN) = 0.78V,
IQ = 70µA, ISD < 1µA, 3mm × 3mm DFN-10, MSOP-10E
LT3980
58V with Transient Protection to 80V, 2A (IOUT), 2.4MHz, High Efficiency
Step-Down DC/DC Converter with Burst Mode Operation
VIN = 3.6V to 58V, Transients to 80V, VOUT(MIN) = 0.79V,
IQ = 75µA, ISD < 1µA, 3mm × 4mm DFN-16, MSOP-16E
LT3971
38V, 1.2A (IOUT), 2MHz, High Efficiency Step-Down DC/DC Converter
with Only 2.8µA of Quiescent Current
VIN = 4.2V to 38V, VOUT(MIN) = 1.2V, IQ = 2.8µA, ISD < 1µA,
3mm × 3mm DFN-10, MSOP-10E
LT3991
55V, 1.2A (IOUT), 2MHz, High Efficiency Step-Down DC/DC Converter
with Only 2.8µA of Quiescent Current
VIN = 4.2V to 55V, VOUT(MIN) = 1.2V, IQ = 2.8µA, ISD < 1µA,
3mm × 3mm DFN-10, MSOP-10E
3692afb
42 Linear Technology Corporation
LT 0412 REV B • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507 ● www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2011