AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com Fully Integrated, 8-Channel Ultrasound Analog Front End, 0.75 nV/rtHz, 14/12-Bit, 65 MSPS, 158 mW/CH Check for Samples: AFE5803 FEATURES DESCRIPTION • The AFE5803 is a highly integrated Analog Front-End (AFE) solution specifically designed for ultrasound systems in which high performance and small size are required. The AFE5803 integrates a complete time-gain-control (TGC) imaging path. It also enables users to select one of various power/noise combinations to optimize system performance. Therefore, the AFE5803 is a suitable ultrasound analog front end solution for portable systems. 1 • • • • • • • • • • 8-Channel Complete Analog Front-End – LNA, VCAT, PGA, LPF, ADC Programmable Gain Low-Noise Amplifier (LNA) – 24/18/12 dB Gain – 0.25/0.5/1 VPP Linear Input Range – 0.63/0.7/0.9 nV/rtHz Input Referred Noise – Programmable Active Termination 40 dB Low Noise Voltage Controlled Attenuator (VCAT) 24/30 dB Programmable Gain Amplifier (PGA) 3rd Order Linear Phase Low-Pass Filter (LPF) – 10, 15, 20, 30 MHz 14-bit Analog to Digital Converter (ADC) – 77 dBFS SNR at 65 MSPS – LVDS Outputs Noise/Power Optimizations (Full Chain) – 158 mW/CH at 0.75 nV/rtHz, 65 MSPS – 101 mW/CH at 1.1 nV/rtHz, 40 MSPS Excellent Device-to-Device Gain Matching – ±0.5 dB (Typical) and ±0.9 dB (Max) Low Harmonic Distortion Fast and Consistent Overload Recovery Small Package: 15 mm x 9 mm, 135-BGA APPLICATIONS • • Medical Ultrasound Imaging Nondestructive Evaluation Equipments The AFE5803 contains eight channels of voltage controlled amplifier (VCA), 14/12-bit Analog-to-Digital Converter (ADC). The VCA includes Low noise Amplifier (LNA), Voltage controlled Attenuator (VCAT), Programmable Gain Amplifier (PGA), and Low-Pass Filter (LPF). The LNA gain is programmable to support 250 mVPP to 1 VPP input signals. Programmable active termination is also supported by the LNA. The ultra-low noise VCAT provides an attenuation control range of 40 dB and improves overall low gain SNR which benefits harmonic imaging and near field imaging. The PGA provides gain options of 24 dB and 30 dB. Before the ADC, a LPF can be configured as 10 MHz, 15 MHz, 20 MHz or 30 MHz to support ultrasound applications with different frequencies. The high-performance 14bit/65 MSPS ADC in the AFE5803 achieves 77dBFS SNR. It ensures excellent SNR at low chain gain. The ADC’s LVDS outputs enable flexible system integration desired for miniaturized systems. The AFE5803 is available in a 15mm × 9mm, 135-pin BGA package and it is specified for operation from 0°C to 85°C. It is also pin-to-pin compatible to the AFE5807, AFE5808 and AFE5808A. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2012, Texas Instruments Incorporated AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. SPI IN AFE5803 (1 of 8 Channels) SPI OUT SPI Logic VCAT 0 to -40dB LNA 3rd LP Filter 10, 15, 20, 30 MHz PGA 24, 30dB LNA IN 14Bit ADC LVDS Reference Reference Differential TGC Vcntl EXT/INT REFs Figure 1. Block Diagram PACKAGING/ORDERING INFORMATION (1) (1) 2 PRODUCT PACKAGE TYPE OPERATING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY AFE5803 ZCF 0°C to 85°C AFE5803ZCF Tray, 160 For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) VALUE Supply voltage range UNIT MIN MAX AVDD –0.3 3.9 V AVDD_ADC –0.3 2.2 V AVDD_5V –0.3 6 V DVDD –0.3 2.2 V Voltage between AVSS and LVSS –0.3 0.3 V Voltage at analog inputs and digital inputs –0.3 min [3.6,AVDD+0.3] V 260 °C 105 °C 150 °C Peak solder temperature (2) Maximum junction temperature (TJ), any condition –55 Storage temperature range 85 °C Human Body Model (HBM) 2000 V Charged Device Model (CDM) 500 V Operating temperature range ESD Ratings (1) (2) 0 Stresses above those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied Exposure to absolute maximum rated conditions for extended periods may degrade device reliability. Device complies with JSTD-020D. THERMAL INFORMATION AFE5803 THERMAL METRIC (1) BGA UNITS 135 PINS θJA Junction-to-ambient thermal resistance θJCtop Junction-to-case (top) thermal resistance θJB Junction-to-board thermal resistance 11.5 ψJT Junction-to-top characterization parameter 0.2 ψJB Junction-to-board characterization parameter 10.8 θJCbot Junction-to-case (bottom) thermal resistance n/a (1) 34.1 5 °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. RECOMMENDED OPERATING CONDITIONS PARAMETER MIN MAX AVDD 3.15 3.6 V 1.7 1.9 V V AVDD_ADC DVDD AVDD_5V Ambient Temperature, TA 1.7 1.9 4.75 5.5 V 0 85 °C Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 UNIT 3 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com DEVICE INFORMATION PIN CONFIGURATION Top View ZCF (BGA-135) 1 2 3 4 5 6 7 8 9 A AVDD INP8 INP7 INP6 INP5 INP4 INP3 INP2 INP1 B CM_BYP ACT8 ACT7 ACT6 ACT5 ACT4 ACT3 ACT2 ACT1 C AVSS INM8 INM7 INM6 INM5 INM4 INM3 INM2 INM1 D AVSS AVSS AVSS AVSS AVSS AVSS AVSS AVDD AVDD E CH7_TEST_OUTP CH7_TEST_OUTM AVSS AVSS AVSS AVSS AVSS AVDD AVDD F CH7_BUFFER_OUTM CH7_BUFFER_OUTP AVSS AVSS AVSS AVSS AVSS DNC DNC G AVSS AVSS AVSS AVSS AVSS AVSS AVSS DNC DNC H CH8_BUFFER_OUTM CH8_BUFFER_OUTP AVSS AVSS AVSS AVSS AVSS PDN_GLOBAL RESET J CH8_TEST_OUTP CH8_TEST_OUTM AVSS AVSS AVSS AVDD_ADC AVDD_ADC PDN_VCA SCLK K AVDD AVDD_5V VCNTLP VCNTLM VHIGH AVSS DNC AVDD_ADC SDATA L CLKP_ADC CLKM_ADC AVDD_ADC REFM DNC DNC DNC PDN_ADC SEN M AVDD_ADC AVDD_ADC VREF_IN REFP DNC DNC DNC DNC SDOUT N D8P D8M DVDD DNC DVSS DNC DVDD D1M D1P P D7M D6M D5M FCLKM DVSS DCLKM D4M D3M D2M R D7P D6P D5P FCLKP DVSS DCLKP D4P D3P D2P PIN FUNCTIONS PIN NO. NAME B9~ B2 ACT1...ACT8 DESCRIPTION Active termination input pins for CH1~8. 1 μF capacitors are recommended. See the Applicaiton Information section. A1, D8, D9, E8, AVDD E9, K1 3.3 V Analog supply for LNA, VCAT, PGA, LPF blocks. K2 AVDD_5V 5 V Analog supply for LNA, VCAT, PGA, LPF blocks. J6, J7, K8, L3, M1, M2 AVDD_ADC 1.8 V Analog power supply for ADC. C1, D1~D7, E3~E7, F3~F7, G1~G7, H3~H7,J3~J5, K6 AVSS Analog ground. L2 CLKM_ADC Negative input of differential ADC clock. In the single-end clock mode, it can be tied to GND directly or through a 0.1 µF capacitor. L1 CLKP_ADC Positive input of differential ADC clock. In the single-end clock mode, it can be tied to clock signal directly or through a 0.1 µF capacitor. B1 CM_BYP Bias voltage and bypass to ground. ≥1µF is recommended. To suppress the ultra low frequency noise, 10µF can be used. E2 CH7_TEST_OUTM CH7 PGA negative output when PGA test mode is enabled. Can be floated if not used. E1 CH7_TEST_OUTP CH7 PGA positive output when PGA test mode is enabled. Can be floated if not used. F1 CH7_BUFFER_OUTM Negative differential output for the buffer amplifier when PGA test mode is enabled. Can be floated if not used. See the TEST MODES in the application information section. F2 CH7_BUFFER_OUTP Positive differential output for the buffer amplifier when PGA test mode is enabled. Can be floated if not used. See the TEST MODES in the application information section. J2 CH8_TEST_OUTM CH8 PGA negative output when PGA test mode is enabled. Can be floated if not used. J1 CH8_TEST_OUTP CH8 PGA positive output when PGA test mode is enabled. Can be floated if not used. H1 CH8_BUFFER_OUTM Negative differential output for the buffer amplifier when PGA test mode is enabled. Can be floated if not used. See the TEST MODES in the application information section. H2 CH8_BUFFER_OUTP Positive differential output for the buffer amplifier when PGA test mode is enabled. Can be floated if not used. See the TEST MODES in the application information section. N8, P9~P7, P3~P1, N2 D1M~D8M ADC CH1~8 LVDS negative outputs N9, R9~R7, R3~R1, N1 D1P~D8P ADC CH1~8 LVDS positive outputs P6 DCLKM LVDS bit clock (7x) negative output 4 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com PIN FUNCTIONS (continued) PIN NO. NAME R6 DCLKP DESCRIPTION LVDS bit clock (7x) positive output F8, F9, G8, G9, K7, DNC L5~L7,M5~M8, N4, N6 Do not connect. Must leave floated N3, N7 DVDD ADC digital and I/O power supply, 1.8 V N5, P5, R5 DVSS ADC digital ground P4 FCLKM LVDS frame clock (1X) negative output R4 FCLKP LVDS frame clock (1X) positive output C9~C2 INM1…INM8 CH1~8 complimentary analog inputs. Bypass to ground with ≥ 0.015 µF capacitors. The HPF response of the LNA depends on the capacitors. A9~A2 INP1...INP8 CH1~8 analog inputs. AC couple to inputs with ≥ 0.1µF capacitors. L8 PDN_ADC ADC partial (fast) power down control pin with an internal pull down resistor of 100 kΩ. Active High. J8 PDN_VCA VCA partial (fast) power down control pin with an internal pull down resistor of 20 kΩ. Active High. H8 PDN_GLOBAL Global (complete) power-down control pin for the entire chip with an internal pull down resistor of 20kΩ. Active High. L4 REFM 0.5 V reference output in the internal reference mode. Must leave floated in the internal reference mode. Adding test point on PCB is recommended for monitoring the reference output. M4 REFP 1.5 V reference output in the internal reference mode. Must leave floated in the internal reference mode. Adding test point on PCB is recommended for monitoring the reference output. H9 RESET Hardware reset pin with an internal pull-down resistor of 20 kΩ. Active high. J9 SCLK Serial interface clock input with an internal pull-down resistor of 2 0kΩ K9 SDATA Serial interface data input with an internal pull-down resistor of 20 kΩ M9 SDOUT Serial interface data readout. High impedance when readout is disabled. L9 SEN Serial interface enable with an internal pull up resistor of 20 kΩ. Active low. K4 VCNTLM Negative differential attenuation control pin. K3 VCNTLP Positive differential attenuation control pin K5 VHIGH Bias voltage; bypass to ground with ≥1µF. M3 VREF_IN ADC 1.4 V reference input in the external reference mode; bypass to ground with 0. 1 µF. F8, F9, G8, G9, K7, L5~L7, DNC M5~M8, N4, N6 Do not connect. Must leave floated Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 5 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, AC-coupled with 0.1µF at INP and bypassed to ground with 15nF at INM, No active termination, VCNTL = 0 V, fIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14Bit, sample rate = 65 MSPS, LPF Filter = 15 MHz, low noise mode, VOUT = –1 dBFS, ADC configured in internal reference mode, single-ended VCNTL mode, VCNTLM = GND, at ambient temperature TA = 25°C, unless otherwise noted. Min and max values are specified across full-temperature range with AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V PARAMETER TEST CONDITION MIN TYP MAX UNITS TGC FULL SIGNAL CHANNEL (LNA+VCAT+LPF+ADC) en (RTI) NF Input voltage noise over LNA Gain(low noise mode) Rs = 0 Ω, f = 2 MHz, LNA =24/18/12 dB, PGA = 2 4dB 0.76/0.83/1.16 Rs = 0 Ω, f = 2 MHz,LNA =24/18/12 dB, PGA = 30 dB 0.75/0.86/1.12 Input voltage noise over LNA Gain(low power mode) Rs = 0 Ω, f = 2 MHz,LNA =24/18/12 dB, PGA = 24 dB 1.1/1.2/1.45 Rs = 0 Ω, f = 2 MHz, LNA =24/18/12 dB, PGA = 30 dB 1.1/1.2/1.45 Input Voltage Noise over LNA Gain(Medium Power Mode) Rs = 0 Ω, f = 2 MHz,LNA = 24/18/12 dB, PGA = 24 dB 1/1.05/1.25 Rs = 0 Ω, f = 2 MHz, LNA = 24/18/12 dB, PGA = 30 dB 0.95/1.0/1.2 Input referred current noise Low Noise Mode/Medium Power Mode/Low Power Mode Noise figure nV/rtHz nV/rtHz nV/rtHz 2.7/2.1/2 pA/rtHz Rs = 200 Ω, 200 Ω active termination, PGA = 24dB,LNA = 12/18/24 dB 3.85/2.4/1.8 dB Rs = 100 Ω, 100 Ω active termination, PGA = 24dB,LNA = 12/18/24 dB 5.3/3.1/2.3 dB VMAX Maximum Linear Input Voltage LNA gain = 24/18/12 dB 250/500/1000 VCLAMP Clamp Voltage Reg52[10:9] = 0, LNA = 24/18/12 dB 350/600/1150 Low noise mode mVPP 24/30 PGA Gain dB Medium/Low power mode Total gain Ch-CH Noise Correlation Factor without Signal (1) Ch-CH Noise Correlation Factor with Signal (1) LNA = 24 dB, PGA = 30 dB, Low noise mode 54 LNA = 2 4dB, PGA = 30 dB, Med power mode 52.5 LNA = 24 dB, PGA = 30 dB, Low power mode 52.5 Summing of 8 channels 0.15/0.17 1MHz band over carrier (VCNTL= 0/0.8) VCNTL = 0, LNA = 18 dB, PGA =24 dB 0.18/0.75 68 70 59.3 63 VCNTL = 0, LNA = 24 dB, PGA = 24 dB Narrow Band SNR SNR over 2 MHz band around carrier at VCNTL = 0.6 V ( 22 dB total gain) Input Common-mode Voltage At INP and INM pins dB 0 Full band (VCNTL = 0/0.8) VCNTL = 0.6V(22 dB total channel gain) Signal to Noise Ratio (SNR) 24/28.5 dBFS 58 75 77 dBFS 2.4 V 8 kΩ Input resistance Preset active termination enabled Input capacitance Input Control Voltage VCNTLP - VCNTLM Common-mode voltage VCNTLP and VCNTLM Gain Range pF 0 1.5 V 0.75 V -40 dB VCNTL= 0.1 V to 1.1 V 35 dB/V Input Resistance Between VCNTLP and VCNTLM 200 KΩ Input Capacitance Between VCNTLP and VCNTLM 1 pF TGC Response Time VCNT L= 0 V to 1.5 V step function 1.5 µs 10, 15, 20, 30 MHz Settling time for change in LNA gain 14 µs Settling time for change in active termination setting 1 µs Noise correlation factor is defined as Nc/(Nu+Nc), where Nc is the correlated noise power in single channel; and Nu is the uncorrelated noise power in single channel. Its measurement follows the below equation, in which the SNR of single channel signal and the SNR of summed eight channel signal are measured. NC = 10 8CH_SNR 10 10 Nu + NC 6 Ω 20 Gain Slope 3rd order-Low-pass Filter (1) 50/100/200/400 1CH_SNR 1 x 1 - 56 7 10 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS (continued) AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, AC-coupled with 0.1µF at INP and bypassed to ground with 15nF at INM, No active termination, VCNTL = 0 V, fIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14Bit, sample rate = 65 MSPS, LPF Filter = 15 MHz, low noise mode, VOUT = –1 dBFS, ADC configured in internal reference mode, single-ended VCNTL mode, VCNTLM = GND, at ambient temperature TA = 25°C, unless otherwise noted. Min and max values are specified across full-temperature range with AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V PARAMETER TEST CONDITION MIN TYP MAX UNITS AC ACCURACY ±5% LPF Bandwidth tolerance CH-CH group delay variation 2 MHz to 15 MHz 2 ns CH-CH Phase variation 15 MHz signal 11 Degree 0 V < VCNTL < 0.1 V (Dev-to-Dev) Gain matching ±0.5 0.1 V < VCNTL < 1.1 V(Dev-to-Dev) –0.9 ±0.5 0.9 0.1 V < VCNTL < 1.1 V(Dev-to-Dev) Temp = 0°C and 85°C –1.1 ±0.5 1.1 1.1 V < VCNTL < 1.5 V(Dev-to-Dev) ±0.5 Gain matching Channel-to-Channel ±0.25 Output offset Vcntl= 0, PGA = 30 dB, LNA = 24 dB –75 dB dB 75 LSB AC PERFORMANCE HD2 HD3 THD Second-Harmonic Distortion Third-Harmonic Distortion Total Harmonic Distortion Fin = 2 MHz; VOUT = -1 dBFS –60 Fin = 5 MHz; VOUT = -1 dBFS –60 Fin = 5 MHz; VIN= 500 mVpp, VOUT = –1dBFS, LNA = 18dB, VCNTL=0.88 V –55 Fin = 5 MHz; Vin = 250 mVpp, VOUT =–1 dBFS, LNA = 24dB, VCNTL= 0.88 V –55 Fin = 2 MHz; VOUT = –1dBFS –55 Fin = 5 MHz; VOUT = –1dBFS –55 Fin = 5 MHz; VIN = 500 mVpp, VOUT = –1 dBFS, LNA = 18 dB, VCNTL= 0.88 V –55 Fin = 5 MHz; VIN = 2 50 mVpp, VOUT = –1 dBFS, LNA = 24 dB, VCNTL= 0.88 V –55 Fin = 2 MHz; VOUT=–1 dBFS –55 Fin = 5 MHz; VOUT=–1 dBFS –55 dBc dBc dBc IMD3 Intermodulation distortion f1 = 5 MHz at –1dBFS, f2 = 5.01 MHz at –27 dBFS –60 XTALK Cross-talk Fin = 5 MHz; VOUT= –1 dBFS –65 dB Phase Noise 1 kHz off 5 MHz (VCNTL=0V) –132 dBc/Hz Input Referred Voltage Noise Rs = 0 Ω, f = 2MHz, Rin = High Z, Gain = 24/18/12 dB High-Pass Filter -3 dB Cut-off Frequency dBc LNA LNA linear output 0.63/0.70/0.9 nV/rtHz 50/100/150/200 KHz 4 VPP 2/10.5 nV/rtHz 1.75 nV/rtHz 80 KHz VCAT+ PGA VCAT Input Noise 0dB/-40 dB Attenuation PGA Input Noise 24 dB/30 dB -3dB HPF cut-off Frequency ADC SPECIFICATIONS Sample rate SNR Signal-to-noise ratio 10 65 MSPS Idle channel SNR of ADC 14b 77 dBFS REFP 1.5 V REFM 0.5 V VREF_IN Voltage 1.4 V VREF_IN Current 50 µA 2 Vpp 65MSPS at 14 bit 910 Mbps Internal reference mode External reference mode ADC input full-scale range LVDS Rate Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 7 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS (continued) AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, AC-coupled with 0.1µF at INP and bypassed to ground with 15nF at INM, No active termination, VCNTL = 0 V, fIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14Bit, sample rate = 65 MSPS, LPF Filter = 15 MHz, low noise mode, VOUT = –1 dBFS, ADC configured in internal reference mode, single-ended VCNTL mode, VCNTLM = GND, at ambient temperature TA = 25°C, unless otherwise noted. Min and max values are specified across full-temperature range with AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V PARAMETER TEST CONDITION MIN TYP MAX UNITS 3.15 3.3 3.6 V 1.7 1.8 1.9 V 4.75 5 5.5 V 1.7 1.8 1.9 V TGC low noise mode, 65 MSPS 158 190 TGC low noise mode, 40 MSPS 145 TGC medium power mode, 40 MSPS 114 POWER DISSIPATION AVDD Voltage AVDD_ADC Voltage AVDD_5V Voltage DVDD Voltage Total power dissipation per channel mW/CH TGC low power mode, 40 MSPS 101.5 TGC low noise mode, no signal 202 TGC medium power mode, no signal 126 TGC low power mode, no signal 99 TGC low noise mode, 500 mVPP Input,1% duty cycle 210 TGC medium power mode, 500 mVPP Input, 1% duty cycle 133 240 AVDD (3.3V) Current mA TGC low power, 500 mVPP Input, 1% duty cycle 105 TGC mode no signal 25.5 TGC mode, 500 mVPP Input,1% duty cycle 16.5 35 AVDD_5V Current mA TGC low noise mode, no signal 99 TGC medium power mode, no signal 68 TGC low power mode, no signal 55.5 TGC low noise mode, 500 mVPP input,1% duty cycle 102.5 121 VCA Power dissipation mW/CH TGC medium power mode, 500 mVPP Input, 1% duty cycle 71 TGC low power mode, 500 mVPP input,1% duty cycle 59.5 AVDD_ADC(1.8V) Current 65 MSPS 187 205 mA DVDD(1.8V) Current 65 MSPS 77 110 mA 65 MSPS 59 69 50 MSPS 51 40 MSPS 46 20 MSPS 35 ADC Power dissipation/CH Power dissipation in power down mode 25 Complete power-down PDN_Global=High 0.6 mW/CH Time taken to enter power down 1 µs Power-up response time VCA power down 2µs+1% of PDN time µs ADC power down 1 Power supply rejection ratio 8 PDN_VCA = High, PDN_ADC = High Power-down response time Power supply modulation ratio, AVDD and AVDD_5V (2) mW/CH Complete power down 2.5 ms fin = 5 MHz, at 50 mVpp noise at 1 KHz on supply (2) –65 dBc fin = 5 MHz, at 50 mVpp noise at 50 KHz on supply (2) –65 dBc f = 10 kHz,VCNTL = 0 V (high gain), AVDD –40 dBc f = 10 kHz,VCNTL = 0 V(high gain), AVDD_5V –55 dBc f = 10 kHz,VCNTL = 1 V (low gain), AVDD –50 dBc PSMR specification is with respect to input signal amplitude. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com DIGITAL CHARACTERISTICS Typical values are at 25°C, AVDD = 3.3 V, AVDD_5 = 5 V and AVDD_ADC = 1.8 V, DVDD = 1.8 V, 14 bit sample rate = 65 MSPS, unless otherwise noted. Minimum and maximum values are across the full temperature range: TMIN = 0°C to TMAX = +85°C PARAMETER CONDITION MIN TYP MAX UNITS (1) DIGITAL INPUTS/OUTPUTS VIH Logic high input voltage 2 VIL Logic low input voltage 0 3.3 V 0.3 V Logic high input current 200 µA Logic low input current 200 µA 5 pF VOH Input capacitance Logic high output voltage SDOUT pin DVDD V VOL Logic low output voltage SDOUT pin 0 V LVDS OUTPUTS tsu th Output differential voltage with 100 ohms external differential termination 400 mV Output offset voltage Common-mode voltage 1100 mV FCLKP and FCLKM 1X clock rate 10 65 MHz DCLKP and DCLKM 7X clock rate 70 455 MHz 6X clock rate 60 390 MHz Data setup time (2) Data hold time (2) 350 ps 350 ps ADC INPUT CLOCK CLOCK frequency 10 Clock duty cycle 45% Sine-wave, ac-coupled Clock input amplitude, differential(VCLKP_ADC–VCLKM_ADC) (1) (2) 65 50% MSPS 55% 0.5 Vpp LVPECL, ac-coupled 1.6 Vpp LVDS, ac-coupled 0.7 Vpp Common-mode voltage biased internally 1 V Clock input amplitude VCLKP_ADC (single-ended) CMOS CLOCK 1.8 Vpp The DC specifications refer to the condition where the LVDS outputs are not switching, but are permanently at a valid logic level 0 or 1 with 100Ω external termination. Setup and hold time specifications take into account the effect of jitter on the output data and clock. These specifications also assume that the data and clock paths are perfectly matched within the receiver. Any mismatch in these paths within the receiver would appear as reduced timing margins Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 9 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com TYPICAL CHARACTERISTICS AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, ac-coupled with 0.1µF caps at INP and 1 5nF caps at INM, No active termination, VCNTL = 0 V, FIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14 Bit, sample rate = 65 MSPS, LPF Filter = 15 MHz, low noise mode, VOUT = -1dBFS, ADC is configured in internal reference mode, single-ended VCNTL mode, VCNTLM = GND, at ambient temperature TA = 25°C, unless otherwise noted. 45 45 Low noise Medium power Low power 40 35 35 30 Gain (dB) 25 20 25 20 15 15 10 10 5 5 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 Vcntl (V) 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) Figure 3. Gain Variation vs. Temperature, LNA = 18 dB and PGA = 24 dB 9000 8000 8000 7000 7000 3000 Gain (dB) G005 Figure 4. Gain Matching Histogram, VCNTL= 0.3V (34951 channels) Figure 5. Gain Matching Histogram, VCNTL = 0.6V (34951 channels) 8000 Number of Occurrences 7000 Number of Occurrences 6000 5000 4000 3000 2000 1000 120 110 100 90 80 70 60 50 40 30 20 10 0 −72 −68 −64 −60 −56 −52 −48 −44 −40 −36 −32 −28 −24 −20 −16 −12 −8 −4 0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 68 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 −0.1 −0.2 −0.3 −0.4 −0.5 −0.6 0 −0.7 0.6 Gain (dB) G004 Gain (dB) ADC Output G005 Figure 6. Gain Matching Histogram, VCNTL = 0.9V (34951 channels) 10 0.5 0.4 0.3 −0.7 0.5 0.4 0.3 0.2 0 0.1 −0.1 −0.2 −0.3 −0.4 −0.5 −0.6 −0.7 −0.8 0 −0.9 1000 0 0.2 2000 1000 0 2000 4000 0.1 3000 5000 −0.1 4000 6000 −0.2 5000 −0.3 6000 −0.4 Number of Occurrences 9000 −0.5 Figure 2. Gain vs. VCNTL, LNA = 18 dB and PGA = 24 dB −0.6 Gain (dB) 30 Number of Occurrences −40 deg C 25 deg C 85 deg C 40 G058 Figure 7. Output Offset Histogram, VCNTL = 0V (1247 channels) Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) Impedance Magnitude Response Impedance Phase Response 10 Open 12000 −10 Phase (Degrees) 10000 Impedance (Ohms) Open 0 8000 6000 4000 −20 −30 −40 −50 −60 −70 2000 −80 500k 4.5M 8.5M 12.5M 16.5M −90 500k 20.5M 4.5M 8.5M Frequency (Hz) Figure 8. Input Impedance without Active Termination (Magnitude) Impedance Magnitude Response 20.5M Impedance Phase Response 10 50 Ohms 100 Ohms 200 Ohms 400 Ohms 450 400 350 0 −10 Phase (Degrees) Impedance (Ohms) 16.5M Figure 9. Input Impedance without Active Termination (Phase) 500 300 250 200 150 −20 −30 −40 −50 −60 100 −70 50 −80 0 500k 4.5M 8.5M 12.5M 16.5M 50 Ohms 100 Ohms 200 Ohms 400 Ohms −90 500k 20.5M Frequency (Hz) 4.5M 8.5M 12.5M 16.5M 20.5M Frequency (Hz) Figure 10. Input Impedance with Active Termination (Magnitude) Figure 11. Input Impedance with Active Termination (Phase) LNA INPUT HPF CHARECTERISTICS 5 10MHz 15MHz 20MHz 30MHz 0 −5 3 0 −3 −6 Amplitude (dB) Amplitude (dB) 12.5M Frequency (Hz) −10 −15 −20 −9 −12 −15 −18 −21 −25 −30 01 00 11 10 −24 −27 0 10 20 30 40 50 Frequency (MHz) 60 −30 10 100 500 Frequency (KHz) Figure 12. Low-Pass Filter Response Figure 13. LNA High-Pass Filter Response vs. Reg59[3:2] Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 11 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) HPF CHARECTERISTICS (LNA+VCA+PGA+ADC) 60 0 Hz) 50 −5 Input reffered noise (nV 5 40 Amplitude (dB) −10 −15 −20 −25 −30 −35 −40 10 100 LNA 12 dB LNA 18 dB LNA 24 dB 30 20 10 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) 500 Frequency (KHz) Figure 14. Full Channel High-Pass Filter Response at Default Register Setting Figure 15. IRN, PGA = 24 dB and Low Noise Mode Hz) 3.0 70 LNA 12 dB LNA 18 dB LNA 24 dB 2.5 Input reffered noise (nV Input reffered noise (nV Hz) 3.5 2.0 1.5 1.0 0.5 0.0 0.0 0.1 0.2 Vcntl (V) 0.3 Hz) 3.0 Input reffered noise (nV Hz) Input reffered noise (nV 40 30 20 10 70 LNA 12 dB LNA 18 dB LNA 24 dB 2.5 2.0 1.5 1.0 0.1 0.2 Vcntl (V) 0.3 0.4 Figure 18. IRN, PGA = 24 dB and Medium Power Mode 12 50 Figure 17. IRN, PGA = 24 dB and Medium Power Mode 4.0 0.5 0.0 LNA 12 dB LNA 18 dB LNA 24 dB 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) 0.4 Figure 16. IRN, PGA = 24 dB and Low Noise Mode 3.5 60 60 LNA 12 dB LNA 18 dB LNA 24 dB 50 40 30 20 10 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) Figure 19. IRN, PGA = 24 dB and Low Power Mode Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) 220 210 3.5 Hz) LNA 12 dB LNA 18 dB LNA 24 dB 3.0 Output reffered noise (nV Input reffered noise (nV Hz) 4.0 2.5 2.0 1.5 1.0 0.1 0.2 Vcntl (V) 0.3 150 130 110 90 70 30 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) 0.4 LNA 12 dB LNA 18 dB LNA 24 dB Output reffered noise (nV 300 280 260 240 220 200 180 160 140 120 100 80 60 40 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Vcntl (V) Figure 21. ORN, PGA = 24 dB and Low Noise Mode Hz) Figure 20. IRN, PGA = 24 dB and Low Power Mode Hz) 170 50 0.5 0.0 Output reffered noise (nV LNA 12 dB LNA 18 dB LNA 24 dB 190 1.0 1.1 1.2 Figure 22. ORN, PGA = 24 dB and Medium Power Mode 340 320 300 280 260 240 220 200 180 160 140 120 100 80 60 40 LNA 12 dB LNA 18 dB LNA 24 dB 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Vcntl (V) 1 1.1 1.2 Figure 23. ORN, PGA = 24 dB and Low Power Mode 1.5 180.0 1.4 160.0 1.1 1.0 0.9 0.8 0.7 0.6 0.5 Hz) 1.2 140.0 Amplitude (nV Amplitude (nV Hz) 1.3 120.0 100.0 80.0 60.0 0.4 0.3 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 Frequency (MHz) 9.0 10.0 11.0 12.0 Figure 24. IRN, PGA = 24 dB and Low Noise Mode 40.0 1.0 3.0 5.0 7.0 Frequency (MHz) 9.0 11.0 12.0 Figure 25. ORN, PGA = 24 dB and Low Noise Mode Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 13 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com 75 70 70 SNR (dBFS) SNR (dBFS) TYPICAL CHARACTERISTICS (continued) 75 65 60 65 60 24 dB PGA gain 30 dB PGA gain 24 dB PGA gain 30 dB PGA gain 55 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) 55 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) Figure 26. SNR, LNA = 18 dB and Low Noise Mode Figure 27. SNR, LNA = 18 dB and Low Power Mode 73 9 Low noise Low power 71 7 Noise Figure (dB) SNR (dBFS) 69 67 65 63 61 5 4 3 1 0 3 6 9 0 12 15 18 21 24 27 30 33 36 39 42 Gain (dB) 50 100 150 200 250 300 350 400 Source Impedence (Ω) Figure 28. SNR vs. Different Power Modes Figure 29. Noise Figure, LNA = 12 dB and Low Noise Mode 10 8 50 ohm act term 100 ohm act term 200 ohm act term 400 ohm act term Without Termination 8 7 50 ohm act term 100 ohm act term 200 ohm act term 400 ohm act term No Termination 7 6 Noise Figure (dB) 9 Noise Figure (dB) 6 2 59 57 100 ohm act term 200 ohm act term 400 ohm act term Without Termination 8 6 5 4 3 5 4 3 2 2 1 1 0 50 100 150 200 250 300 350 400 0 50 Source Impedence (Ω) 150 200 250 300 350 400 Source Impedence (Ω) Figure 30. Noise Figure, LNA = 18 dB and Low Noise Mode 14 100 Figure 31. Noise Figure, LNA = 24 dB and Low Noise Mode Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) 4.5 4 3.5 2.5 1.5 Low noise Low power Medium power Noise Figure (dB) Noise Figure (dB) Low noise Low power Medium power 50 100 150 200 250 300 350 3 2 1 400 50 100 150 Source Impedence (Ω) Figure 32. Noise Figure vs. Power Modes with 400 Ω Termination 300 350 400 −45 Low noise Low power Medium power −55.0 Low noise Low power Medium power −50 −55 HD3 (dBc) −60.0 HD2 (dB) 250 Figure 33. Noise Figure vs. Power Modes without Termination −50.0 −65.0 −60 −70.0 −65 −75.0 −70 −80.0 200 Source Impedence (Ω) 1 2 3 4 5 6 7 Frequency (MHz) 8 9 −75 10 Figure 34. HD2 vs. Frequency, Vin = 500 mVPP and VOUT = -1 dBFS 1 2 3 4 5 6 7 Frequency (MHz) 8 9 10 Figure 35. HD3 vs. Frequency, Vin = 500 mVpp and VOUT = -1 dBFS −40 −40 Low noise Low power Medium power −45 −50 Low noise Low power Medium power −50 HD3 (dBc) HD2 (dBc) −55 −60 −65 −70 −60 −70 −75 −80 −80 −85 −90 6 12 18 24 30 36 −90 6 Gain (dB) 12 18 24 30 36 Gain (dB) Figure 36. HD2 vs. Gain, LNA = 12 dB and PGA = 24 dB and VOUT = -1 dBFS Figure 37. HD3 vs. Gain, LNA = 12 dB and PGA = 24 dB and VOUT = -1 dBFS Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 15 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) −40 −40 Low noise Low power Medium power −50 HD3 (dBc) HD2 (dBc) −50 −60 −70 −60 −70 −80 −90 Low noise Low power Medium power −80 12 18 24 30 36 −90 42 12 18 24 Gain (dB) 30 36 42 Gain (dB) Figure 38. HD2 vs. Gain, LNA = 18 dB and PGA = 24 dB and VOUT = -1 dBFS Figure 39. HD3 vs. Gain, LNA = 18 dB and PGA = 24 dB and VOUT = -1 dBFS −40 −40 Low noise Low power Medium power −45 −50 Low noise Low power Medium power −50 HD2 (dBc) −55 −60 HD3 (dB) −60 −65 −70 −70 −75 −80 −80 −85 −90 18 24 30 36 42 −90 48 18 21 24 27 Gain (dB) Figure 40. HD2 vs. Gain, LNA = 24 dB and PGA = 24 dB and VOUT = -1 dBFS 42 45 48 Fin1=2MHz, Fin2=2.01MHz Fin1=5MHz, Fin2=5.01MHz −54 IMD3 (dBFS) −54 IMD3 (dBFS) 39 −50 Fin1=2MHz, Fin2=2.01MHz Fin1=5MHz, Fin2=5.01MHz −58 −62 −66 −58 −62 −66 14 18 22 26 30 Gain (dB) 34 38 42 −70 14 G001 Figure 42. IMD3, Fout1 = -1 dBFS and Fout2 = -21 dBFS 16 33 36 Gain (dB) Figure 41. HD3 vs. Gain, LNA = 24 dB and PGA = 24 dB and VOUT = -1 dBFS −50 −70 30 18 22 26 30 Gain (dB) 34 38 42 G001 Figure 43. IMD3, Fout1 = -7dBFS and Fout2 = -7dBFS Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) PSMR vs SUPPLY FREQUENCY PSMR vs SUPPLY FREQUENCY −60 −55 Vcntl = 0 Vcntl = 0.3 Vcntl = 0.6 Vcntl = 0.9 −60 −65 PSMR (dBc) PSMR (dBc) Vcntl = 0 Vcntl = 0.3 Vcntl = 0.6 Vcntl = 0.9 −65 −70 −70 −75 5 10 100 −80 1000 2000 5 10 100 Supply frequency (kHz) Figure 44. AVDD Power Supply Modulation Ratio, 100 mVPP Supply Noise with Different Frequencies Figure 45. AVDD_5V Power Supply Modulation Ratio, 100mVPP Supply Noise with Different Frequencies 3V PSRR vs SUPPLY FREQUENCY 5V PSRR vs SUPPLY FREQUENCY −20 −20 Vcntl = 0 Vcntl = 0.3 Vcntl = 0.6 Vcntl = 0.9 −40 Vcntl = 0 Vcntl = 0.3 Vcntl = 0.6 Vcntl = 0.9 −30 PSRR wrt supply tone (dB) PSRR wrt supply tone (dB) −30 −50 −60 −70 −80 −90 −40 −50 −60 −70 −80 5 10 100 −90 1000 2000 5 10 100 Supply frequency (kHz) 16000.0 14000.0 12000.0 10000.0 8000.0 6000.0 4000.0 2000.0 0.0 0.0 0.5 1.0 1.5 Time (µs) 2.0 2.5 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 −0.1 3.0 Figure 48. VCNTL Response Time, LNA = 18 dB and PGA = 24 dB Figure 47. AVDD_5 V Power Supply Rejection Ratio, 100mVPP Supply Noise with Different Frequencies 20000.0 18000.0 Output Code Vcntl 16000.0 14000.0 Output Code Output Code Vcntl Vcntl (V) 20000.0 18000.0 1000 2000 Supply frequency (kHz) Figure 46. AVDD Power Supply Rejection Ratio, 100mVPP Supply Noise with Different Frequencies Output Code 1000 2000 Supply frequency (kHz) 12000.0 10000.0 8000.0 6000.0 4000.0 2000.0 0.0 0.0 0.2 0.5 0.8 1.0 1.2 1.5 Time (µs) 1.8 2.0 2.2 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 −0.1 2.5 Vcntl (V) −75 Figure 49. VCNTL Response Time, LNA = 18 dB and PGA = 24 dB Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 17 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com 1.2 1.0 1.0 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 Input (V) Input (V) TYPICAL CHARACTERISTICS (continued) 1.2 0.0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1.0 −1.0 −1.2 0.0 2.0 4.0 6.0 −1.2 0.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 Time (µs) Figure 50. Pulse Inversion Asymmetrical Positive Input 10000.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 Time (µs) 47nF 15nF 6000 4000 Output Code Output Code 6.0 8000 4000.0 2000.0 0.0 −2000.0 2000 0 −2000 −4000.0 −4000 −6000.0 −6000 −8000.0 −8000 −10000.0 0.0 1.0 2.0 3.0 Time (µs) 4.0 5.0 6.0 −10000 Figure 52. Pulse Inversion, VIN = 2 VPP, PRF = 1 KHz, Gain = 21 dB 0 0.5 1 1.5 2 2.5 3 Time (µs) 3.5 4 4.5 5 Figure 53. Overload Recovery Response vs. INM Capacitor, VIN = 50 mVPP/100 µVPP, Max Gain 10 2000 47nF 15nF 1600 5 0 1200 −5 Gain (dB) 800 Output Code 4.0 10000 6000.0 400 0 −400 k=2 k=3 k=4 k=5 k=6 k=7 k=8 k=9 k=10 −10 −15 −20 −25 −800 −30 −1200 −35 −1600 −2000 2.0 Figure 51. Pulse Inversion Asymmetrical Negative Input Positive overload Negative overload Average 8000.0 −40 1 1.5 2 2.5 3 3.5 Time (µs) 4 4.5 0 0.2 5 Figure 54. Overload Recovery Response vs. INM Capacitor (Zoomed), VIN = 50 mVPP/100 µVPP, Max Gain 18 0.0 −0.2 0.4 0.6 0.8 1 1.2 1.4 Frequency (MHz) 1.6 1.8 2 G000 Figure 55. Digital High-Pass Filter Response Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com TIMING CHARACTERISTICS (1) Typical values are at 25°C, AVDD_5V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, Differential clock, CLOAD = 5pF, RLOAD = 100 Ω, 14Bit, sample rate = 65MSPS, unless otherwise noted. Minimum and maximum values are across the full temperature range TMIN = 0°C to TMAX = 85°C with AVDD_5V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V PARAMETER ta TEST CONDITIONS Aperture delay Aperture delay matching tj MIN The delay in time between the rising edge of the input sampling clock and the actual time at which the sampling occurs 0.7 Across channels within the same device Aperture jitter TYP MAX 3 ns ±150 ps 450 Fs rms 11/8 Input clock cycles ADC latency Default, after reset, or / 0 x 2 [12] = 1, LOW_LATENCY = 1 tdelay Data and frame clock delay Input clock rising edge (zero cross) to frame clock rising edge (zero cross) minus 3/7 of the input clock period (T). Δtdelay Delay variation At fixed supply and 20°C T difference. Device to device Data rise time Data fall time Rise time measured from –100 mV to 100 mV Fall time measured from 100 mV to –100 mV 10 MHz < fCLKIN < 65 MHz 0.14 Frame clock rise time Frame clock fall time Rise time measured from –100mV to 100mV Fall time measured from 100 mV to –100 mV 10 MHz < fCLKIN < 65MHz 0.14 Frame clock duty cycle Zero crossing of the rising edge to zero crossing of the falling edge Bit clock rise time Bit clock fall time Rise time measured from –100mV to 100mV Fall time measured from 100 mV to –100 mV 10 MHz < fCLKIN < 65MHz Bit clock duty cycle Zero crossing of the rising edge to zero crossing of the falling edge 10 MHz < fCLKIN < 65 MHz tRISE tFALL tFCLKRISE tFCLKFALL tDCLKRISE tDCLKFALL (1) 3 UNIT 5.4 –1 7 ns 1 ns ns 0.15 ns 0.15 48% 50% 52% 0.13 ns 0.12 46% 54% Timing parameters are ensured by design and characterization; not production tested. OUTPUT INTERFACE TIMING (1) (2) (3) fCLKIN, Input Clock Frequency (1) (2) (3) Setup Time (tsu), ns (for output data and frame clock) Hold Time (th), ns (for output data and frame clock) tPROG = (3/7)x T + tdelay, ns Data Valid to Input Clock Zero-Crossing Input Clock Zero-Crossing to Data Invalid Input Clock Zero-Cross (rising edge) to Frame Clock Zero-Cross (rising edge) MHz MIN TYP MIN TYP MIN TYP MAX 65/14bit 0.24 0.37 MAX 0.24 0.38 MAX 11 12 12.5 50/14bit 0.41 0.54 0.46 0.57 13 13.9 14.4 40/14bit 0.55 0.70 0.61 0.73 15 16 16.7 30/14bit 0.87 1.10 0.94 1.1 18.5 19.5 20.1 20/14bit 1.30 1.56 1.46 1.6 25.7 26.7 27.3 FCLK timing is the same as for the output data lines. It has the same relation to DCLK as the data pins. Setup and hold are the same for the data and the frame clock. Data valid is logic HIGH = +100mV and logic LOW = -100mV Timing parameters are ensured by design and characterization; not production tested. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 19 12-Bit 6x serialization mode 20 Output Data CHnOUT Data rate = 14 x fCLKIN Bit Clock DCLK Freq = 7 x fCLKIN Frame Clock FCLK Freq = fCLKIN Input Clock CLKIN Freq = fCLKIN Input Signal D0 D13 D12 D1 (D12) (D13) (D0) (D1) D11 (D2) Submit Documentation Feedback Product Folder Link(s): AFE5803 D13 (D0) D10 D9 (D3) (D4) D6 D5 (D7) (D8) Bit Clock Output Data Pair Data bit in LSB First mode D13 D12 (D0) (D1) CHi out tsu DCLKM DCLKP Cd clock cycles latency D4 D3 D2 D1 D0 (D9) (D10) (D11) (D12) (D13) Data bit in MSB First mode SAMPLE N-Cd D8 D7 (D5) (D6) ta Sample N th D11 D10 (D2) (D3) Dn D7 D6 (D6) (D7) SAMPLE N-1 D9 D8 (D4) (D5) Sample N+Cd ta Dn + 1 tsu th D5 D4 D3 D2 D1 D0 D13 D12 (D8) (D9) (D10) (D11) (D12) (D13) (D0) (D1) tPROG tPROG D11 D10 (D2) (D3) T D7 D6 (D6) (D7) SAMPLE N D9 D8 (D4) (D5) Sample N+Cd+1 D10 (D1) T0434-01 D1 D0 D11 D5 D4 D3 D2 (D8) (D9) (D10) (D11) (D12) (D13) (D0) AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com LVDS Setup and Hold Timing 14-Bit 7x serialization mode Figure 56. LVDS Timing Diagrams Copyright © 2012, Texas Instruments Incorporated AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com LVDS Output Interface Description AFE5803 has LVDS output interface which supports multiple output formats. The ADC resolutions can be configured as 12bit or 14bit as shown in the LVDS timing diagrams Figure 56. The ADCs in the AFE5803 are running at 14bit; 2 LSBs are removed when 12-bit output is selected; and two 0s are added at LSBs when 16-bit output is selected. Appropriate ADC resolutions can be selected for optimizing system performance-cost effectiveness. When the devices run at 16bit mode, higher end FPGAs are required to process higher rate of LVDS data. Corresponding register settings are listed in Table 1. Table 1. Corresponding Register Settings LVDS Rate 12 bit (6X DCLK) 14 bit (7X DCLK) 16 bit (8X DCLK) Reg 3 [14:13] 11 00 01 Reg 4 [2:0] 010 000 000 Description 2 LSBs removed N/A 2 0s added at LSBs SERIAL REGISTER TIMING Serial Register Write Description Programming of different modes can be done through the serial interface formed by pins SEN (serial interface enable), SCLK (serial interface clock), SDATA (serial interface data) and RESET. All these pins have a pull-down resistor to GND of 100kΩ. Serial shift of bits into the device is enabled when SEN is low. Serial data SDATA is latched at every rising edge of SCLK when SEN is active (low). The serial data is loaded into the register at every 24th SCLK rising edge when SEN is low. If the word length exceeds a multiple of 24 bits, the excess bits are ignored. Data can be loaded in multiple of 24-bit words within a single active SEN pulse (there is an internal counter that counts groups of 24 clocks after the falling edge of SEN). The interface can work with the SCLK frequency from 20 MHz down to low speeds (few Hertz) and even with non-50% duty cycle SCLK. The data is divided into two main portions: a register address (8 bits) and the data itself (16 bits), to load on the addressed register. When writing to a register with unused bits, these should be set to 0. Figure 57 illustrates this process. Start Sequence End Sequence SEN t6 t7 t1 t2 Data Latched On Rising Edge of SCLK SCLK t3 SDATA A7 A5 A6 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 t4 t5 Start Sequence End Sequence RESET T0384-01 Figure 57. SPI Timing Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 21 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com SPI Timing Characteristics Minimum values across full temperature range TMIN = 0°C to TMAX = 85°C, AVDD_5V =5.0V, AVDD=3.3V, AVDD_ADC=1.8V, DVDD=1.8V PARAMETER DESCRIPTION MIN TYP MAX UNIT t1 SCLK period 50 ns t2 SCLK high time 20 ns t3 SCLK low time 20 ns t4 Data setup time 5 ns t5 Data hold time 5 ns t6 SEN fall to SCLK rise 8 ns t7 Time between last SCLK rising edge to SEN rising edge t8 SDOUT delay 8 ns 12 20 28 ns Register Readout The device includes an option where the contents of the internal registers can be read back. This may be useful as a diagnostic test to verify the serial interface communication between the external controller and the AFE. First, the <REGISTER READOUT ENABLE> bit (Reg0[1]) needs to be set to '1'. Then user should initiate a serial interface cycle specifying the address of the register (A7-A0) whose content has to be read. The data bits are "don’t care". The device will output the contents (D15-D0) of the selected register on the SDOUT pin. SDOUT has a typical delay t8 of 20nS from the falling edge of the SCLK. For lower speed SCLK, SDOUT can be latched on the rising edge of SCLK. For higher speed SCLK,e.g. the SCLK period lesser than 60nS, it would be better to latch the SDOUT at the next falling edge of SCLK. The following timing diagram shows this operation (the time specifications follow the same information provided. In the readout mode, users still can access the <REGISTER READOUT ENABLE> through SDATA/SCLK/SEN. To enable serial register writes, set the <REGISTER READOUT ENABLE> bit back to '0'. Start Sequence End Sequence SEN t6 t7 t1 t2 SCLK t3 A7 SDATA A6 A5 A4 A3 t4 A2 A1 A0 x x x x x x x x x x x x x x x x D6 D5 D4 D3 D2 D1 D0 t8 t5 D15 D14 D13 D12 D11 D10 D9 SDOUT D8 D7 Figure 58. Serial Interface Register Read The AFE5803 SDOUT buffer is tri-stated and will get enabled only when 0[1] (REGISTER READOUT ENABLE) is enabled. SDOUT pins from multiple AFE5803s can be tied together without any pull-up resistors. Level shifter SN74AUP1T04 can be used to convert 1.8V logic to 2.5V/3.3V logics if needed. 22 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com t1 AVDD AVDD_5V AVDD_ADC t2 DVDD t3 t4 t7 t5 RESET t6 Device Ready for Serial Register Write SEN Start of Clock Device Ready for Data Conversion CLKP_ADC t8 10 µs < t1 < 50 ms, 10 µs < t2 < 50 ms, –10 ms < t3 < 10 ms, t4 > 10 ms, t5 > 100 ns, t6 > 100 ns, t7 > 10 ms, and t8 > 100 µs. The AVDDx and DVDD power-on sequence does not matter as long as –10ms < t3 < 10ms. Similar considerations apply while shutting down the device. Figure 59. Recommended Power-up Sequencing and Reset Timing Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 23 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com REGISTER MAP ADC Register Map A reset process is required at the AFE5803 initialization stage. Initialization can be done in one of two ways: 1. Through a hardware reset, by applying a positive pulse at the RESET pin 2. Through a software reset, using the serial interface, by setting the SOFTWARE RESET bit to high. Setting this bit initializes the internal registers to the respective default values (all zeros) and then self-resets the SOFTWARE RESET bit to low. In this case, the RESET pin can stay low (inactive). After reset, all ADC and VCA registers are set to ‘0’, i.e. default settings. During register programming, all reserved/unlisted register bits need to be set as ‘0’. Register settings are maintained when the AFE5803 is in either partial power down mode or complete power down mode. Table 2. ADC Register Map ADDRESS (DEC) ADDRESS (HEX) Default Value 0[0] 0x0[0] 0 SOFTWARE_RESET 0: Normal operation; 1: Resets the device and self-clears the bit to '0' 0[1] 0x0[1] 0 REGISTER_READOUT_ENABLE 0:Disables readout; 1: enables readout of register at SDOUT Pin 1[0] 0x1[0] 0 ADC_COMPLETE_PDN 0: Normal 1: Complete Power down 1[1] 0x1[1] 0 LVDS_OUTPUT_DISABLE 0: Output Enabled; 1: Output disabled 1[9:2] 0x1[9:2] 0 ADC_PDN_CH<7:0> 0: Normal operation; 1: Power down. Power down Individual ADC channels. 1[9]→CH8…1[2]→CH1 1[10] 0x1[10] 0 PARTIAL_PDN 0: Normal Operation; 1: Partial Power Down ADC 1[11] 0x1[11] 0 LOW_FREQUENCY_ NOISE_SUPPRESSION 0: No suppression; 1: Suppression Enabled 1[13] 0x1[13] 0 EXT_REF 0: Internal Reference; 1: External Reference. VREF_IN is used. Both 3[15] and 1[13] should be set as 1 in the external reference mode 1[14] 0x1[14] 0 LVDS_OUTPUT_RATE_2X 0: 1x rate; 1: 2x rate. Combines data from 2 channels on 1 LVDS pair. When ADC clock rate is low, this feature can be used 1[15] 0x1[15] 0 SINGLE-ENDED_CLK_MODE 0: Differential clock input; 1: Single-ended clock input 2[2:0] 0x2[2:0] 0 RESERVED Set to 0 2[10:3] 0x2[10:3] 0 POWER-DOWN_LVDS 0: Normal operation; 1: PDN Individual LVDS outputs. 2[10]→CH8…2[3]→CH1 2[11] 0x2[11] 0 AVERAGING_ENABLE 0: No averaging; 1: Average 2 channels to increase SNR 2[12] 0x2[12] 0 LOW_LATENCY 0: Default Latency with digital features supported, 11 cycle latency 1: Low Latency with digital features bypassed, 8 cycle latency 2[15:13] 0x2[15:3] 0 TEST_PATTERN_MODES 000: Normal operation; 001: Sync; 010: De-skew; 011: Custom; 100:All 1's; 101: Toggle; 110: All 0's; 111: Ramp 3[7:0] 0x3[7:0] 0 INVERT_CHANNELS 0: No inverting; 1:Invert channel digital output. 3[7]→CH8;3[0]→CH1 3[8] 0x3[8] 0 CHANNEL_OFFSET_ SUBSTRACTION_ENABLE 0: No offset subtraction; 1: Offset value Subtract Enabled 3[9:11] 0x3[9:11] 0 RESERVED Set to 0 3[12] 0x3[12] 0 DIGITAL_GAIN_ENABLE 0: No digital gain; 1: Digital gain Enabled 24 FUNCTION DESCRIPTION Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com Table 2. ADC Register Map (continued) ADDRESS (DEC) ADDRESS (HEX) Default Value 3[14:13] 0x3[14:13] 0 SERIALIZED_DATA_RATE Serialization factor 00: 14x 01: 16x 10: reserved 11: 12x when 4[1]=1. In the 16x serialization rate, two 0s are filled at two LSBs (see Table 1) 3[15] 0x3[15] 0 ENABLE_EXTERNAL_ REFERENCE_MODE 0: Internal reference mode; 1: Set to external reference mode Note: both 3[15] and 1[13] should be set as 1 when configuring the device in the external reference mode 4[1] 0x4[1] 0 ADC_RESOLUTION_SELECT 0: 14bit; 1: 12bit 4[3] 0x4[3] 0 ADC_OUTPUT_FORMAT 0: 2's complement; 1: Offset binary 4[4] 0x4[4] 0 LSB_MSB_FIRST 0: LSB first; 1: MSB first 5[13:0] 0x5[13:0] 0 CUSTOM_PATTERN Custom pattern data for LVDS output (2[15:13]=011) 10[8] 0xA[8] 0 SYNC_PATTERN 0: Test pattern outputs of 8 channels are NOT synchronized. 1: Test pattern outputs of 8 channels are synchronized. 13[9:0] 0xD[9:0] 0 OFFSET_CH1 Value to be subtracted from channel 1 code 13[15:11] 0xD[15:11] 0 DIGITAL_GAIN_CH1 0 dB to 6 dB in 0. 2dB steps 15[9:0] 0xF[9:0] 0 OFFSET_CH2 value to be subtracted from channel 2 code 15[15:11] 0xF[15:11] 0 DIGITAL_GAIN_CH2 0dB to 6dB in 0.2 dB steps 17[9:0] 0x11[9:0] 0 OFFSET_CH3 value to be subtracted from channel 3 code 17[15:11] 0x11[15:11] 0 DIGITAL_GAIN_CH3 0 dB to 6 dB in 0.2 dB steps 19[9:0] 0x13[9:0] 0 OFFSET_CH4 value to be subtracted from channel 4 code 19[15:11] 0x13[15:11] 0 DIGITAL_GAIN_CH4 0 dB to 6 dB in 0. 2dB steps 21[0] 0x15[0] 0 DIGITAL_HPF_FILTER_ENABLE _ CH1-4 0: Disable the digital HPF filter; 1: Enable for 1-4 channels 21[4:1] 0x15[4:1] 0 DIGITAL_HPF_FILTER_K_CH1-4 Set K for the high-pass filter (k from 2 to 10, i.e. 0010B to 1010B). This group of four registers controls the characteristics of a digital high-pass transfer function applied to the output data, following the formula: y(n) = 2k/(2k + 1) [x(n) – x(n – 1) + y(n – 1)] (see Table 3 and Figure 55) 25[9:0] 0x19[9:0] 0 OFFSET_CH8 value to be subtracted from channel 8 code 25[15:11] 0x19[15:11] 0 DIGITAL_GAIN_CH8 0 dB to 6 dB in 0.2dB steps 27[9:0] 0x1B[9:0] 0 OFFSET_CH7 value to be subtracted from channel 7 code 27[15:11] 0x1B[15:11] 0 DIGITAL_GAIN_CH7 0 dB to 6dB in 0.2 dB steps 29[9:0] 0x1D[9:0] 0 OFFSET_CH6 value to be subtracted from channel 6 code 29[15:11] 0x1D[15:11] 0 DIGITAL_GAIN_CH6 0 dB to 6 dB in 0.2 dB steps 31[9:0] 0x1F[9:0] 0 OFFSET_CH5 value to be subtracted from channel 5 code 31[15:11] 0x1F[15:11] 0 DIGITAL_GAIN_CH5 0 dB to 6 dB in 0.2 dB steps 33[0] 0x21[0] 0 DIGITAL_HPF_FILTER_ENABLE _ CH5-8 0: Disable the digital HPF filter; 1: Enable for 5-8 channels 33[4:1] 0x21[4:1] 0 DIGITAL_HPF_FILTER_K_CH5-8 Set K for the high-pass filter (k from 2 to 10, 010B to 1010B) This group of four registers controls the characteristics of a digital high-pass transfer function applied to the output data, following the formula: y(n) = 2k/(2k + 1) [x(n) – x(n – 1) + y(n – 1)] (see Table 3 and Figure 55) 66[15] 0x42[15] 0 DITHER 0: Disable dither function. 1: Enable dither function. Improve the ADC linearity with slight noise degradation. FUNCTION DESCRIPTION Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 25 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com ADC Register/Digital Processing Description The ADC in the AFE5803 has extensive digital processing functionalities which can be used to enhance ultrasound system performance. The digital processing blocks are arranged as in Figure 60. ADC Output Channel Average Default=No 12/14b Digital Gain Default=0 Digital HPF Default = No 12/14b Final Digital Output Digital Offset Default=No Figure 60. ADC Digital Block Diagram AVERAGING_ENABLE: Address: 2[11] When set to 1, two samples, corresponding to two consecutive channels, are averaged (channel 1 with 2, 3 with 4, 5 with 6, and 7 with 8). If both channels receive the same input, the net effect is an improvement in SNR. The averaging is performed as: • Channel 1 + channel 2 comes out on channel 3 • Channel 3 + channel 4 comes out on channel 4 • Channel 5 + channel 6 comes out on channel 5 • Channel 7 + channel 8 comes out on channel 6 ADC_OUTPUT_FORMAT: Address: 4[3] The ADC output, by default, is in 2’s-complement mode. Programming the ADC_OUTPUT_FORMAT bit to 1 inverts the MSB, and the output becomes straight-offset binary mode. DIGITAL_GAIN_ENABLE: Address: 3[12] Setting this bit to 1 applies to each channel i the corresponding gain given by DIGTAL_GAIN_CHi <15:11>. The gain is given as 0dB + 0.2dB × DIGTAL_GAIN_CHi<15:11>. For instance, if DIGTAL_GAIN_CH5<15:11> = 3, channel 5 is increased by 0.6dB gain. DIGTAL_GAIN_CHi <15:11> = 31 produces the same effect as DIGTAL_GAIN_CHi <15:11> = 30, setting the gain of channel i to 6dB. DIGITAL_HPF_ENABLE • CH1-4: Address 21[0] • CH5-8: Address 33[0] DIGITAL_HPF_FILTER_K_CHX • CH1-4: Address 21[4:1] • CH5-8: Address 3[4:1] This group of registers controls the characteristics of a digital high-pass transfer function applied to the output data, following Equation 1. y (n ) = 2k 2k + 1 éë x (n ) - x (n - 1) + y (n - 1)ùû (1) These digital HPF registers (one for the first four channels and one for the second group of four channels) describe the setting of K. The digital high pass filter can be used to suppress low frequency noise which commonly exists in ultrasound echo signals. The digital filter can significantly benefit near field recovery time due to T/R switch low frequency response. Table 3 shows the cut-off frequency vs K, also see Figure 55. 26 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com Table 3. Digital HPF –1dB Corner Frequency vs K and Fs k 40 MSPS 50 MSPS 65 MSPS 2 2780 KHz 3480 KHz 4520 KHz 3 1490 KHz 1860 KHz 2420 KHz 4 770 KHz 960 KHz 1250 KHz LOW_FREQUENCY_NOISE_SUPPRESSION: Address: 1[11] The low-frequency noise suppression mode is especially useful in applications where good noise performance is desired in the frequency band of 0MHz to 1MHz (around dc). Setting this mode shifts the low-frequency noise of the AFE5803 to approximately Fs/2, thereby moving the noise floor around dc to a much lower value. Register bit 1[11] is used for enabling or disabling this feature. When this feature is enabled, power consumption of the device will be increased by approximate 1 mW/CH. LVDS_OUTPUT_RATE_2X: Address: 1[14] The output data always uses a DDR format, with valid/different bits on the positive as well as the negative edges of the LVDS bit clock, DCLK. The output rate is set by default to 1X (LVDS_OUTPUT_RATE_2X = 0), where each ADC has one LVDS stream associated with it. If the sampling rate is low enough, two ADCs can share one LVDS stream, in this way lowering the power consumption devoted to the interface. The unused outputs will output zero. To avoid consumption from those outputs, no termination should be connected to them. The distribution on the used output pairs is done in the following way: • Channel 1 and channel 2 come out on channel 3. Channel 1 comes out first. • Channel 3 and channel 4 come out on channel 4. Channel 3 comes out first. • Channel 5 and channel 6 come out on channel 5. Channel 5 comes out first. • Channel 7 and channel 8 come out on channel 6. Channel 7 comes out first CHANNEL_OFFSET_SUBSTRACTION_ENABLE: Address: 3[8] Setting this bit to 1 enables the subtraction of the value on the corresponding OFFSET_CHx<9:0> (offset for channel i) from the ADC output. The number is specified in 2s-complement format. For example, OFFSET_CHx<9:0> = 11 1000 0000 means subtract –128. For OFFSET_CHx<9:0> = 00 0111 1111 the effect is to subtract 127. In effect, both addition and subtraction can be performed. Note that the offset is applied before the digital gain (see DIGITAL_GAIN_ENABLE). The whole data path is 2s-complement throughout internally, with digital gain being the last step. Only when ADC_OUTPUT_FORMAT=1 (straight binary output format) is the 2s-complement word translated into offset binary at the end. SERIALIZED_DATA_RATE: Address: 3[14:13] See Table 1 for detail description. TEST_PATTERN_MODES: Address: 2[15:13] The AFE5803 can output a variety of test patterns on the LVDS outputs. These test patterns replace the normal ADC data output. The device may also be made to output 6 preset patterns: 1. Ramp: Setting Register 2[15:13]=111causes all the channels to output a repeating full-scale ramp pattern. The ramp increments from zero code to full-scale code in steps of 1LSB every clock cycle. After hitting the full-scale code, it returns back to zero code and ramps again. 2. Zeros: The device can be programmed to output all zeros by setting Register 2[15:13]=110; 3. Ones: The device can be programmed to output all 1s by setting Register 2[15:13]=100; 4. Deskew Patten: When 2[15:13]=010; this mode replaces the 14-bit ADC output with the 01010101010101 word. 5. Sync Pattern: When 2[15:13]=001, the normal ADC output is replaced by a fixed 11111110000000 word. 6. Toggle: When 2[15:13]=101, the normal ADC output is alternating between 1's and 0's. The start state of ADC word can be either 1's or 0's. 7. Custom Pattern: It can be enabled when 2[15:13]= 011;. Users can write the required VALUE into register bits <CUSTOM PATTERN> which is Register 5[13:0]. Then the device will output VALUE at its outputs, about 3 to 4 ADC clock cycles after the 24th rising edge of SCLK. So, the time taken to write one value is 24 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 27 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com SCLK clock cycles + 4 ADC clock cycles. To change the customer pattern value, users can repeat writing Register 5[13:0] with a new value. Due to the speed limit of SPI, the refresh rate of the custom pattern may not be high. For example, 128 points custom pattern will take approximately 128 x (24 SCLK clock cycles + 4 ADC clock cycles). NOTE only one of the above patterns can be active at any given instant. SYNC_PATTERN: Address: 10[8] By enabling this bit, all channels' test pattern outputs are synchronized. When 10[8] is set as 1, the ramp patterns of all 8 channels start simultaneously. 28 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com VCA Register Map Table 4. VCA Register Map ADDRESS (DEC) ADDRESS (HEX) Default Value FUNCTION DESCRIPTION 51[0] 0x33[0] 0 RESERVED 0 51[3:1] 0x33[3:1] 0 LPF_PROGRAMMABILITY 000: 15MHz, 010: 20MHz, 011: 30MHz, 100: 10MHz 51[4] 0x33[4] 0 PGA_INTEGRATOR_DISABLE (PGA_HPF_DISABLE) 0: Enable 1: Disables offset integrator for PGA. See explanation for the PGA integrator function in APPLICATION INFORMATION section 51[6:5] 0x33[6:5] 0 PGA_CURRENT_CLAMP_LEVEL 00: –2dBFS; 10: 0dBFS; 01:–4dBFS when 51[7]=0 Note: the current clamp circuit makes sure that PGA output is in linear range. For example, at 00 setting, PGA output HD3 will be worsen by 3dB at –2dBFS ADC input. In normal operation, the current clamp function can be set as 00 51[7] 0x33[7] 0 PGA_CURRENT_CLAMP_DISABLE 0:Enables the PGA current clamp circuit; 1:Disables the PGA current clamp circuit before the PGA outputs. 51[6:5] determines the current clamp level 51[13] 0x33[13] 0 PGA_GAIN_CONTROL 0:24dB; 1:30dB. 52[4:0] 0x34[4:0] 0 ACTIVE_TERMINATION_ INDIVIDUAL_RESISTOR_CNTL See Table 6 Reg 52[5] should be set as '1' to access these bits 52[5] 0x34[5] 0 ACTIVE_TERMINATION_ INDIVIDUAL_RESISTOR_ENABLE 0: Disables; 1: Enables internal active termination individual resistor control 52[7:6] 0x34[7:6] 0 PRESET_ACTIVE_ TERMINATIONS 00: 50ohm, 01: 100ohm, 10: 200ohm, 11: 400ohm. (Note: the device will adjust resistor mapping (52[4:0]) automatically. 50ohm active termination is NOT supported in 12dB LNA setting. Instead, '00' represents high impedance mode when LNA gain is 12dB) 52[8] 0x34[8] 0 ACTIVE TERMINATION ENABLE 0: Disables; 1: Enables active termination 52[10:9] 0x34[10:9] 0 LNA_INPUT_CLAMP_SETTING 00: Auto setting, 01: 1.5Vpp, 10: 1.15Vpp and 11: 0.6Vpp 52[11] 0x34[11] 0 RESERVED Set to 0 52[12] 0x34[12] 0 LNA_INTEGRATOR_DISABLE (LNA_HPF_DISABLE) 0: Enables; 1: Disables offset integrator for LNA. See the explanation for this function in the following section 52[14:13] 0x34[14:13] 0 LNA_GAIN 00: 18dB; 01: 24dB; 10: 12dB; 11: Reserved 52[15] 0x34[15] 0 LNA_INDIVIDUAL_CH_CNTL 0: Disable; 1: Enable LNA individual channel control. See Register 57 for details 53[7:0] 0x35[7:0] 0 PDN_CH<7:0> 0: Normal operation; 1: Powers down corresponding channels. Bit7→CH8, Bit6→CH7…Bit0→CH1. PDN_CH will shut down whichever blocks are active 53[8] 0x35[8] 0 RESERVED Set to 0 53[9] 0x35[9] 0 RESERVED Set to 0 53[10] 0x35[10] 0 LOW_POWER 0: Low noise mode; 1: Sets to low power mode (53[11]=0). At 30dB PGA, total chain gain may slightly change. See typical characteristics Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 29 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com Table 4. VCA Register Map (continued) ADDRESS (DEC) ADDRESS (HEX) Default Value FUNCTION DESCRIPTION 53[11] 0x35[11] 0 MED_POWER 0: Low noise mode; 1: Sets to medium power mode(53[10]=0). At 30dB PGA, total chain gain may slightly change. See typical characteristics 53[12] 0x35[12] 0 PDN_VCAT_PGA 0: Normal operation; 1: Powers down VCAT (voltage-controlled-attenuator) and PGA 53[13] 0x35[13] 0 PDN_LNA 0: Normal operation; 1: Powers down LNA only 53[14] 0x35[14] 0 VCA_PARTIAL_PDN 0: Normal operation; 1: Powers down LNA, VCAT, and PGA partially(fast wake response) 53[15] 0x35[15] 0 VCA_COMPLETE_PDN 0: Normal operation; 1: Powers down LNA, VCAT, and PGA completely (slow wake response). This bit can overwrite 53[14]. 54[4:0] 0x36[4:0] 0 BUFFER_AMP_GAIN_CNTL Selects Feedback resistor for the buffer amplifier see Table 7 54[7] 0x36[7] 0 RESERVED Set to 0 54[8] 0x36[8] 0 RESERVED Set to 0 54[9] 0x36[9] 0 RESERVED Set to 0 57[1:0] 0x39[1:0] 0 CH1_LNA_GAIN_CNTL 57[3:2] 0x39[3:2] 0 00: 18dB; 01: 24dB; 10: 12dB; 11: Reserved REG52[15] should be set as '1' CH2_LNA_GAIN_CNTL 57[5:4] 0x39[5:4] 0 CH3_LNA_GAIN_CNTL 57[7:6] 0x39[7:6] 0 CH4_LNA_GAIN_CNTL 57[9:8] 0x39[9:8] 0 CH5_LNA_GAIN_CNTL 57[11:10] 0x39[11:10] 0 CH6_LNA_GAIN_CNTL 57[13:12] 0x39[13:12] 0 CH7_LNA_GAIN_CNTL 57[15:14] 0x39[15:14] 0 CH8_LNA_GAIN_CNTL 59[3:2] 0x3B[3:2] 0 HPF_LNA 00: 100kHz; 01: 50kHz; 10: 200kHz; 11: 150kHz with 0.015uF on INMx 59[6:4] 0x3B[6:4] 0 DIG_TGC_ATT_GAIN 000: 0dB attenuation; 001: 6dB attenuation; N: ~N×6dB attenuation when 59[7] = 1 59[7] 0x3B[7] 0 DIG_TGC_ATT 0: disable digital TGC attenuator; 1: enable digital TGC attenuator 59[8] 0x3B[8] 0 BUFFER_AMP_PDN 0: Power down; 1: Normal operation 59[9] 0x3B[9] 0 PGA_TEST_MODE 0: Normal operation; 1: PGA outputs appear at test outputs 30 00: 18dB; 01: 24dB; 10: 12dB; 11: Reserved REG52[15] should be set as '1' Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com AFE5803 VCA Register Description LNA Input Impedances Configuration (Active Termination Programmability) Different LNA input impedances can be configured through the register 52[4:0]. By enabling and disabling the feedback resistors between LNA outputs and ACTx pins, LNA input impedance is adjustable accordingly. Table 5 describes the relationship between LNA gain and 52[4:0] settings. The AFE5803 also has 4 preset active termination impedances as described in 52[7:6]. An internal decoder is used to select appropriate resistors corresponding to different LNA gain. Table 5. Register 52[4:0] Description 52[4:0]/0x34[4:0] FUNCTION 00000 No feedback resistor enabled 00001 Enables 450 Ω feedback resistor 00010 Enables 900 Ω feedback resistor 00100 Enables 1800 Ω feedback resistor 01000 Enables 3600 Ω feedback resistor 10000 Enables 4500 Ω feedback resistor Table 6. Register 52[4:0] vs LNA Input Impedances 52[4:0]/0x34[4:0] 00000 00001 00010 00011 00100 00101 00110 00111 LNA:12dB High Z 150 Ω 300 Ω 100 Ω 600 Ω 120 Ω 200 Ω 86 Ω LNA:18dB High Z 90 Ω 180 Ω 60 Ω 360 Ω 72 Ω 120 Ω 51 Ω LNA:24dB High Z 50 Ω 100 Ω 33 Ω 200 Ω 40 Ω 66.67 Ω 29 Ω 52[4:0]/0x34[4:0] 01000 01001 01010 01011 01100 01101 01110 01111 LNA:12dB 1200 Ω 133 Ω 240 Ω 92 Ω 400 Ω 109 Ω 171 Ω 80 Ω LNA:18dB 720 Ω 80 Ω 144 Ω 55 Ω 240 Ω 65 Ω 103 Ω 48 Ω LNA:24dB 400 Ω 44 Ω 80 Ω 31 Ω 133 Ω 36 Ω 57 Ω 27 Ω 52[4:0]/0x34[4:0] 10000 10001 10010 10011 10100 10101 10110 10111 LNA:12dB 1500 Ω 136 Ω 250 Ω 94 Ω 429 Ω 111 Ω 176 Ω 81 Ω LNA:18dB 900 Ω 82 Ω 150 Ω 56 Ω 257 Ω 67 Ω 106 Ω 49 Ω LNA:24dB 500 Ω 45 Ω 83 Ω 31 Ω 143 Ω 37 Ω 59 Ω 27 Ω 52[4:0]/0x34[4:0] 11000 11001 11010 11011 11100 11101 11110 11111 LNA:12dB 667 Ω 122 Ω 207 Ω 87 Ω 316 Ω 102 Ω 154 Ω 76 Ω LNA:18dB 400 Ω 73 Ω 124 Ω 52 Ω 189 Ω 61 Ω 92 Ω 46 Ω LNA:24dB 222 Ω 41 Ω 69 Ω 29 Ω 105 Ω 34 Ω 51 Ω 25 Ω Programmable Feedback Resistors for Buffer Amplifier in TGC Test Mode Different feedback resistors can be configured for the buffer amplifier through the register 54[4:0] when TGC test mode is enabled. Therefore, certain gain can be applied to the PGA test outputs for CH7 and CH8. Table 7 describes the relationship between the resistor configurations and 54[4:0] settings. Note these 5 resistor are put in parallel. When multiple bits are enabled, the resistance is reduced. Table 7. Register 54[4:0] Description 54[4:0] FUNCTION 00000 No feedback resistor enabled 00001 Enables 250 Ω feedback resistor 00010 Enables 250 Ω feedback resistor 00100 Enables 500 Ω feedback resistor 01000 Enables 1000 Ω feedback resistor 10000 Enables 2000 Ω feedback resistor Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 31 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com THEORY OF OPERATION AFE5803 OVERVIEW The AFE5803 is a highly integrated Analog Front-End (AFE) solution specifically designed for ultrasound systems in which high performance and small size are required. The AFE5803 integrates a complete time-gain-control (TGC) imaging path. It also enables users to select one of various power/noise combinations to optimize system performance. The AFE5803 contains eight channels; each channels includes a Low-Noise Amplifier (LNA), a Voltage Controlled Attenuator (VCAT), a Programmable Gain Amplifier (PGA), a Low-pass Filter (LPF), and a 14-bit Analog-to-Digital Converter (ADC). In addition, multiple features in the AFE5803 are suitable for ultrasound applications, such as active termination, individual channel control, fast power up/down response, programmable clamp voltage control, fast and consistent overload recovery, etc. Therefore the AFE5803 brings premium image quality to ultra–portable, handheld systems all the way up to high-end ultrasound systems. Its simplified function block diagram is listed in Figure 61. SPI IN AFE5803 (1 of 8 Channels) SPI OUT SPI Logic LNA VCAT 0 to -40dB PGA 24, 30dB LNA IN 3rd LP Filter 10, 15, 20, 30 MHz 14Bit ADC Reference Reference Differential TGC Vcntl EXT/INT REFs LVDS Figure 61. Functional Block Diagram LOW-NOISE AMPLIFIER (LNA) In many high-gain systems, a low noise amplifier is critical to achieve overall performance. Using a new proprietary architecture, the LNA in the AFE5803 delivers exceptional low-noise performance, while operating on a low quiescent current compared to CMOS-based architectures with similar noise performance. The LNA performs single-ended input to differential output voltage conversion. It is configurable for a programmable gain of 24/18/12dB and its input-referred noise is only 0.63/0.70/0.9nV/√Hz respectively. Programmable gain settings result in a flexible linear input range up to 1Vpp, realizing high signal handling capability demanded by new transducer technologies. Larger input signal can be accepted by the LNA; however, the signal can be distorted since it exceeds the LNA’s linear operation region. Combining the low noise and high input range, a wide input dynamic range is achieved consequently for supporting the high demands from various ultrasound imaging modes. The LNA input is internally biased at approximately +2.4 V; the signal source should be ac-coupled to the LNA input by an adequately-sized capacitor, e.g. ≥0.1 µF. To achieve low DC offset drift, the AFE5803 incorporates a DC offset correction circuit for each amplifier stage. To improve the overload recovery, an integrator circuit is used to extract the DC component of the LNA output and then fed back to the LNA’s complementary input for DC offset correction. This DC offset correction circuit has a high-pass response and can be treated as a high-pass filter. The effective corner frequency is determined by the capacitor CBYPASS connected at INM. With larger capacitors, the corner frequency is lower. For stable operation at the highest HP filer cut-off frequency, a ≥15 nF capacitor can be selected. This corner frequency scales almost linearly with the value of the CBYPASS. For example, 15 nF gives a corner frequency of approximately 100 kHz, while 47 nF can give an effective corner frequency of 33 KHz. The DC offset correction circuit can also be disabled/enabled through register 52[12]. 32 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com The AFE5803 can be terminated passively or actively. Active termination is preferred in ultrasound application for reducing reflection from mismatches and achieving better axial resolution without degrading noise figure too much. Active termination values can be preset to 50, 100, 200, 400Ω; other values also can be programmed by users through register 52[4:0]. A feedback capacitor is required between ACTx and the signal source as Figure 62 shows. On the active termination path, a clamping circuit is also used to create a low impedance path when overload signal is seen by the AFE5803. The clamp circuit limits large input signals at the LNA inputs and improves the overload recovery performance of the AFE5803. The clamp level can be set to 350 mVpp, 600 mVpp, 1.15 Vpp automatically depending on the LNA gain settings when register 52[10:9]=0. Other clamp voltages, such as 1.15Vpp, 0.6 Vpp, and 1.5 Vpp, are also achievable by setting register 52[10:9]. This clamping circuit is also designed to obtain good pulse inversion performance and reduce the impact from asymmetric inputs. CLAMP AFE CACT ACTx INPx CIN INPUT CBYPSS INMx LNAx DC Offset Correction Figure 62. AFE5803 LNA with DC Offset Correction Circuit VOLTAGE-CONTROLLED ATTENUATOR The voltage-controlled attenuator is designed to have a linear-in-dB attenuation characteristic; that is, the average gain loss in dB (refer to Figure 2) is constant for each equal increment of the control voltage (VCNTL) as shown in Figure 63. A differential control structure is used to reduce common mode noise. A simplified attenuator structure is shown in the following Figure 63 and Figure 64. The attenuator is essentially a variable voltage divider that consists of the series input resistor (RS) and seven shunt FETs placed in parallel and controlled by sequentially activated clipping amplifiers (A1 through A7). VCNTL is the effective difference between VCNTLP and VCNTLM. Each clipping amplifier can be understood as a specialized voltage comparator with a soft transfer characteristic and well-controlled output limit voltage. Reference voltages V1 through V7 are equally spaced over the 0V to 1.5Vcontrol voltage range. As the control voltage increases through the input range of each clipping amplifier, the amplifier output rises from a voltage where the FET is nearly OFF to VHIGH where the FET is completely ON. As each FET approaches its ON state and the control voltage continues to rise, the next clipping amplifier/FET combination takes over for the next portion of the piecewise-linear attenuation characteristic. Thus, low control voltages have most of the FETs turned OFF, producing minimum signal attenuation. Similarly, high control voltages turn the FETs ON, leading to maximum signal attenuation. Therefore, each FET acts to decrease the shunt resistance of the voltage divider formed by Rs and the parallel FET network. Additionally, a digitally controlled TGC mode is implemented to achieve better phase-noise performance in the AFE5803. The attenuator can be controlled digitally instead of the analog control voltage VCNTL. This mode can be set by the register bit 59[7]. The variable voltage divider is implemented as a fixed series resistance and FET as the shunt resistance. Each FET can be turned ON by connecting the switches SW1-7. Turning on each of the switches can give approximately 6dB of attenuation. This can be controlled by the register bits 59[6:4]. This digital control feature can eliminate the noise from the VCNTL circuit and ensure the better SNR and phase noise for TGC path. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 33 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com A1 - A7 Attenuator Stages Attenuator Input RS Attenuator Output Q1 VB A1 Q2 A1 Q3 A1 C1 C2 V1 Q4 A1 C3 V2 Q5 A1 C4 V3 Q6 A1 C5 V4 Q7 A1 C6 V5 C7 V6 V7 VCNTL C1 - C8 Clipping Amplifiers Control Input Figure 63. Simplified Voltage Controlled Attenuator (Analog Structure) Attenuator Input RS Attenuator Output Q1 Q2 Q3 Q4 Q5 SW5 SW6 Q6 Q7 VB SW1 SW2 SW3 SW4 SW7 VHIGH Figure 64. Simplified Voltage Controlled Attenuator (Digital Structure) The voltage controlled attenuator’s noise follows a monotonic relationship to the attenuation coefficient. At higher attenuation, the input-referred noise is higher and vice-versa. The attenuator’s noise is then amplified by the PGA and becomes the noise floor at ADC input. In the attenuator’s high attenuation operating range, i.e. VCNTL is high, the attenuator’s input noise may exceed the LNA’s output noise; the attenuator then becomes the dominant noise source for the following PGA stage and ADC. Therefore the attenuator’s noise should be minimized compared to the LNA output noise. The AFE5803’s attenuator is designed for achieving low noise even at high attenuation (low channel gain) and realizing better SNR in near field. The input referred noise for different attenuations is listed in the below table: Table 8. Voltage-Controlled-Attenuator noise vs Attenuation Attenuation (dB) Attenuator Input Referred noise (nV/rtHz) –40 10.5 –36 10 –30 9 –24 8.5 –18 6 –12 4 –6 3 0 2 PROGRAMMABLE GAIN AMPLIFIER (PGA) After the voltage controlled attenuator, a programmable gain amplifier can be configured as 24dB or 30dB with a constant input referred noise of 1.75 nV/rtHz. The PGA structure consists of a differential voltage-to-current converter with programmable gain, current clamp( bias control) circuits, a transimpedance amplifier with a programmable low-pass filter, and a DC offset correction circuit. Its simplified block diagram is shown below: 34 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com Current Clamp From attenuator To ADC I/V LPF V/I Current Clamp DC Offset Correction Loop Figure 65. Simplified Block Diagram of PGA Low input noise is always preferred in a PGA and its noise contribution should not degrade the ADC SNR too much after the attenuator. At the minimum attenuation (used for small input signals), the LNA noise dominates; at the maximum attenuation (large input signals), the PGA and ADC noise dominates. Thus 24 dB gain of PGA achieves better SNR as long as the amplified signals can exceed the noise floor of the ADC. The PGA current clamp circuit can be enabled (register 51) to improve the overload recovery performance of the AFE. If we measure the standard deviation of the output just after overload, for 0.5 V VCNTL, it is about 3.2 LSBs in normal case, i.e the output is stable in about 1 clock cycle after overload. With the current clamp circuit disabled, the value approaches 4 LSBs meaning a longer time duration before the output stabilizes; however, with the current clamp circuit enabled, there will be degradation in HD3 for PGA output levels > -2dBFS. For example, for a –2dBFS output level, the HD3 degrades by approximately 3dB. The AFE5803 integrates an anti-aliasing filter in the form of a programmable low-pass filter (LPF) in the transimpedance amplifier. The LPF is designed as a differential, active, 3rd order filter with a typical 18dB per octave roll-off. Programmable through the serial interface, the –1dB frequency corner can be set to one of 10MHz, 15 MHz, 20 MHz, and 30MHz. The filter bandwidth is set for all channels simultaneously. A selectable DC offset correction circuit is implemented in the PGA as well. This correction circuit is similar to the one used in the LNA. It extracts the DC component of the PGA outputs and feeds back to the PGA’s complimentary inputs for DC offset correction. This DC offset correction circuit also has a high-pass response with a cut-off frequency of 80 KHz. ANALOG TO DIGITAL CONVERTER The analog-to-digital converter (ADC) of the AFE5803 employs a pipelined converter architecture that consists of a combination of multi-bit and single-bit internal stages. Each stage feeds its data into the digital error correction logic, ensuring excellent differential linearity and no missing codes at the 14-bit level. The 14 bits given out by each channel are serialized and sent out on a single pair of pins in LVDS format. All eight channels of the AFE5803 operate from a common input clock (CLKP/M). The sampling clocks for each of the eight channels are generated from the input clock using a carefully matched clock buffer tree. The 14x clock required for the serializer is generated internally from the CLKP/M pins. A 7x and a 1x clock are also given out in LVDS format, along with the data, to enable easy data capture. The AFE5803 operates from internally-generated reference voltages that are trimmed to improve the gain matching across devices. The nominal values of REFP and REFM are 1.5V and 0.5V, respectively. Alternately, the device also supports an external reference mode that can be enabled using the serial interface. Using serialized LVDS transmission has multiple advantages, such as a reduced number of output pins (saving routing space on the board), reduced power consumption, and reduced effects of digital noise coupling to the analog circuit inside the AFE5803. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 35 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com EQUIVALENT CIRCUITS CM CM (a) INP (b) INM (c) ACT S0492-01 Figure 66. Equivalent Circuits of LNA inputs S0493-01 Figure 67. Equivalent Circuits of VCNTLP/M VCM 5 kΩ 5 kΩ CLKP CLKM ADC Input Clocks Figure 68. Equivalent Circuits of Clock Inputs 36 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com + – Low +Vdiff High AFE5803 OUTP + – –Vdiff + – High Vcommon Low External 100-W Load Rout OUTM Switch impedance is nominally 50 W (±10%) Figure 69. Equivalent Circuits of LVDS Outputs Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 37 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com APPLICATION INFORMATION 1.8VA N*0.1μF AVSS N*0.1μF AVSS 10μF 1.8VD DVDD 10μF N*0.1μF DVSS ACT1 D1P 0.1 μF IN1P D1M 15nF IN1M D2P 1μF ACT2 D2M 1μF IN CH1 3.3VA AVDD_ADC 0.1μF AVSS 10μF AVDD 5VA AVDD_5V 10μF Clock termination depends on clock types LVDS, PECL, or CMOS 0.1μF IN CH2 IN CH3 IN CH4 IN CH5 IN CH6 IN CH7 IN CH8 0.1μF 0.1μF IN2P D3P 15nF IN2M D3M 1μF ACT3 D4P 0.1μF IN3P D4M 15nF IN3M D5P 1μF ACT4 D5M 0.1μF IN4P D6P 15nF IN4M D6M 1μF ACT5 0.1μF IN5P 15nF IN5M 1μF ACT6 0.1μF IN6P 15nF IN6M 1μF ACT7 0.1μF IN7P 15nF IN7M 1μF ACT8 0.1μF IN8P CH7_TEST_OUTP 15nF IN8M CH7_BUFFER_OUTM CLOCK INPUTS SCLK D7P SEN VCNTLP IN VCNTLM IN RVCNTL 200Ω 1.4V 0.1μF AFE5803 D7M AFE5803 RESET D8P PDN_VCA D8M ANALOG INPUTS ANALOG OUTPUTS REF/BIAS DECOUPLING LVDS OUTPUTS DIGITAL INPUTS PDN_ADC DCLKP PDN_GLOBAL DCLKM FCLKP FCLKM CH7_TEST_OUTM R (optional) CH7_OUTM CH7_BUFFER_OUTP R (optional) RVCNTL 200Ω AFE5803 SDATA VHIGH >1μF CLKM SOUT CM_BYP >1μF CLKP CH7_OUTP CVCNTL 470pF VCNTLP VCNTLM CVCNTL 470pF VREF_IN CH8_TEST_OUTP CH8_BUFFER_OUTM CH8_TEST_OUTM R (optional) CH8_OUTM CH8_BUFFER_OUTP REFM R (optional) DNCs REFP AVSS CH8_OUTP DVSS Figure 70. Application Circuit 38 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com A typical application circuit diagram is listed above. The configuration for each block is discussed below. LNA CONFIGURATION LNA Input Coupling and Decoupling The LNA closed-loop architecture is internally compensated for maximum stability without the need of external compensation components. The LNA inputs are biased at 2.4 V and AC coupling is required. A typical input configuration is shown in Figure 71. CIN is the input AC coupling capacitor. CACT is a part of the active termination feedback path. Even if the active termination is not used, the CACT is required for the clamp functionality. Recommended values for CACT = 1 µF and CIN are ≥ 0.1 µF. A pair of clamping diodes is commonly placed between the T/R switch and the LNA input. Schottky diodes with suitable forward drop voltage (e.g. the BAT754/54 series, the BAS40 series, the MMBD7000 series, or similar) can be considered depending on the transducer echo amplitude. AFE CLAMP CACT ACTx CIN INPx CBYPASS INMx Input LNAx DC Offset Correction S0498-01 Figure 71. LNA Input Configurations This architecture minimizes any loading of the signal source that may otherwise lead to a frequency-dependent voltage divider. The closed-loop design yields low offsets and offset drift. CBYPASS (≥0.015 µF) is used to set the high-pass filter cut-off frequency and decouple the complimentary input. Its cut-off frequency is inversely proportional to the CBYPASS value, The HPF cut-off frequency can be adjusted through the register 59[3:2] a Table 9 lists. Low frequency signals at T/R switch output, such as signals with slow ringing, can be filtered out. In addition, the HPF can minimize system noise from DC-DC converters, pulse repetition frequency (PRF) trigger, and frame clock. Most ultrasound systems’ signal processing unit includes digital high-pass filters or band-pass filters (BPFs) in FPGAs or ASICs. Further noise suppression can be achieved in these blocks. In addition, a digital HPF is available in the AFE5803 ADC. If low frequency signal detection is desired in some applications, the LNA HPF can be disabled. Table 9. LNA HPF Settings (CBYPASS = 15 nF) Reg59[3:2] (0x3B[3:2]) Frequency 00 100 KHz 01 50 KHz 10 200 KHz 11 150 KHz Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 39 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com CM_BYP and VHIGH pins, which generate internal reference voltages, need to be decoupled with ≥1uF capacitors. Bigger bypassing capacitors (>2.2uF) may be beneficial if low frequency noise exists in system. LNA Noise Contribution The noise spec is critical for LNA and it determines the dynamic range of entire system. The LNA of the AFE5803 achieves low power and an exceptionally low-noise voltage of 0.63 nV/√Hz, and a low current noise of 2.7 pA/√Hz. Typical ultrasonic transducer’s impedance Rs varies from tens of ohms to several hundreds of ohms. Voltage noise is the dominant noise in most cases; however, the LNA current noise flowing through the source impedance (Rs) generates additional voltage noise. 2 2 LNA _ Noise total = VLNAnoise + R2s ´ ILNAnoise (2) The AFE5803 achieves low noise figure (NF) over a wide range of source resistances as shown in Figure 29, Figure 30, andFigure 31. Active Termination In ultrasound applications, signal reflection exists due to long cables between transducer and system. The reflection results in extra ringing added to echo signals in PW mode. Since the axial resolution depends on echo signal length, such ringing effect can degrade the axial resolution. Hence, either passive termination or active termination, is preferred if good axial resolution is desired. Figure 72 shows three termination configurations: Rs LNA (a) No Termination Rf Rs LNA (b) Active Termination Rs Rt LNA (c) Passive Termination S0499-01 Figure 72. Termination Configurations 40 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com Under the no termination configuration, the input impedance of the AFE5803 is about 6 KΩ (8 K//20 pF) at 1 MHz. Passive termination requires external termination resistor Rt, which contributes to additional thermal noise. The LNA supports active termination with programmable values, as shown in Figure 73 . 450Ω 900Ω 1800Ω ACTx 3600Ω 4500Ω INPx Input INMx LNAx AFE S0500-01 Figure 73. Active Termination Implementation The AFE5803 has four pre-settings 50,100, 200 and 400 Ω which are configurable through the registers. Other termination values can be realized by setting the termination switches shown in Figure 73. Register [52] is used to enable these switches. The input impedance of the LNA under the active termination configuration approximately follows: ZIN = Rf AnLNA 1+ 2 (3) Table 5 lists the LNA RINs under different LNA gains. System designers can achieve fine tuning for different probes. The equivalent input impedance is given by Equation 4 where RIN (8 K) and CIN (20 pF) are the input resistance and capacitance of the LNA. ZIN = Rf / /CIN / /RIN AnLNA 1+ 2 (4) Therefore the ZIN is frequency dependent and it decreases as frequency increases shown in Figure 10. Since 2 MHz~10 MHz is the most commonly used frequency range in medical ultrasound, this rolling-off effect doesn’t impact system performance greatly. Since each ultrasound system includes multiple transducers with different impedances, the flexibility of impedance configuration is a great plus. Figure 29, Figure 30, and Figure 31 shows the NF under different termination configurations. It indicates that no termination achieves the best noise figure; active termination adds less noise than passive termination. Thus termination topology should be carefully selected based on each use scenario in ultrasound. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 41 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com LNA Gain Switch Response The LNA gain is programmable through SPI. The gain switching time depends on the SPI speed as well as the LNA gain response time. During the switching, glitches might occur and they can appear as artifacts in images. LNA gain switching in a single imaging line may not be preferred, although digital signal processing might be used here for glitch suppression. VOLTAGE-CONTROLLED-ATTENUATOR The attenuator in the AFE5803 is controlled by a pair of differential control inputs, the VCNTLM/P pins. The differential control voltage spans from 0 V to 1.5 V. This control voltage varies the attenuation of the attenuator based on its linear-in-dB characteristic. Its maximum attenuation (minimum channel gain) appears at VCNTLP VCNTLM = 1.5 V, and minimum attenuation (maximum channel gain) occurs at VCNTLP - VCNTLM = 0. The typical gain range is 40 dB and remains constant, independent of the PGA setting. When only single-ended VCNTL signal is available, this 1.5 VPP signal can be applied on the VCNTLP pin with the VCNTLM pin connected to ground. As shown in Figure 74, TGC gain curve is inversely proportional to the VCNTLPVCNTLM. 1.5V VCNTLP VCNTLM = 0V X+40dB TGC Gain XdB (a) Single-Ended Input at VCNTLP 1.5V VCNTLP 0.75V VCNTLM 0V X+40dB TGC Gain XdB (b) Differential Inputs at VCNTLP and VCNTLM W0004-01 Figure 74. VCNTLP and VCNTLM Configurations 42 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com As discussed in the theory of operation, the attenuator architecture uses seven attenuator segments that are equally spaced in order to approximate the linear-in-dB gain-control slope. This approximation results in a monotonic slope; the gain ripple is typically less than ±0.5 dB. The control voltage input (VCNTLM/P pins) represents a high-impedance input. The VCNTLM/P pins of multiple AFE5803 devices can be connected in parallel with no significant loading effects. When the voltage level (VCNTLP - VCNTLM) is above 1.5 V or below 0 V, the attenuator continues to operate at its maximum attenuation level or minimum attenuation level respectively. It is recommended to limit the voltage from -0.3 V to 2 V. The AFE5803 gain-control input has a –3 dB bandwidth of approximately 800KHz. This wide bandwidth, although useful in many applications (e.g. fast VCNTL response), can also allow high-frequency noise to modulate the gain control input and finally affect the Doppler performance. In practice, this modulation can be avoided by additional external filtering (RVCNTL and CVCNTL) at VCNTLM/P pins as Figure 69 shows. However, the external filter's cutoff frequency cannot be kept too low as this results in low gain response time. Without external filtering, the gain control response time is typically less than 1 μs to settle within 10% of the final signal level of 1VPP (–6 dBFS) output as indicated in Figure 48 and Figure 49. Typical VCNTLM/P signals are generated by an 8bit to 12bit 10MSPS digital to analog converter (DAC) and a differential operation amplifier. TI’s DACs, such as TLV5626 and DAC7821/11 (10 MSPS/12bit), could be used to generate TGC control waveforms. Differential amplifiers with output common mode voltage control (e.g. THS4130 and OPA1632) can connect the DAC to the VCNTLM/P pins. The buffer amplifier can also be configured as an active filter to suppress low frequency noise. More information can be found in the documents SLOS318 and SBAA150. The VCNTL vs Gain curves can be found in Figure 2. The below table also shows the absolute gain vs. VCNTL, which may help program DAC correspondingly. In PW Doppler and color Doppler modes, VCNTL noise should be minimized to achieve the best close-in phase noise and SNR. Digital VCNTL feature is implemented to address this need in the AFE5803. In the digital VCNTL mode, no external VCNTL is needed. Table 10. VCNTLP–VCNTLM vs Gain Under Different LNA and PGA Gain Settings (Low Noise Mode) VCNTLP–VCNTLM (V) Gain (dB) LNA = 12 dB PGA = 24 dB Gain (dB) LNA = 18 dB PGA = 24 dB Gain (dB) LNA = 24 dB PGA = 24 dB Gain (dB) LNA = 12 dB PGA = 30 dB Gain (dB) LNA = 18 dB PGA = 30 dB Gain (dB) LNA = 24 dB PGA = 30 dB 0 36.45 42.45 48.45 42.25 48.25 54.25 0.1 33.91 39.91 45.91 39.71 45.71 51.71 0.2 30.78 36.78 42.78 36.58 42.58 48.58 0.3 27.39 33.39 39.39 33.19 39.19 45.19 0.4 23.74 29.74 35.74 29.54 35.54 41.54 0.5 20.69 26.69 32.69 26.49 32.49 38.49 0.6 17.11 23.11 29.11 22.91 28.91 34.91 0.7 13.54 19.54 25.54 19.34 25.34 31.34 0.8 10.27 16.27 22.27 16.07 22.07 28.07 0.9 6.48 12.48 18.48 12.28 18.28 24.28 1.0 3.16 9.16 15.16 8.96 14.96 20.96 1.1 –0.35 5.65 11.65 5.45 11.45 17.45 1.2 –2.48 3.52 9.52 3.32 9.32 15.32 1.3 –3.58 2.42 8.42 2.22 8.22 14.22 1.4 –4.01 1.99 7.99 1.79 7.79 13.79 1.5 –4 2 8 1.8 7.8 13.8 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 43 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com ADC OPERATION ADC Clock Distribution To ensure that the aperture delay and jitter are the same for all channels, the AFE5803 uses a clock tree network to generate individual sampling clocks for each channel. The clock, for all the channels, are matched from the source point to the sampling circuit of each of the eight internal ADCs. The variation on this delay is described in the aperture delay parameter of the output interface timing. Its variation is given by the aperture jitter number of the same table. FPGA Clock/ Noisy Clock n×(20~65)MHz TI Jitter Cleaner CDCE72010/ CDCM7005 20~65 MHz ADC CLK CDCLVP1208 1-to-8 CLK Buffer CDCE72010 has 10 outputs thus the buffer may not be needed for 64CH systems AFE AFE AFE AFE AFE AFE AFE AFE 8 Synchronized ADC CLKs B0437-01 Figure 75. ADC Clock Distribution Network In the single-end case, it is recommended that the use of low jitter square signals (LVCMOS levels, 1.8 V amplitude). See TI document SLYT075 for further details on the theory. The jitter cleaner CDCM7005 or CDCE72010 is suitable to generate the AFE5803’s ADC clock and ensure the performance for the14 bit ADC with 77 dBFS SNR. A clock distribution network is shown in Figure 75. The AFE5803 can accept differential LVDS, LVPECL, and other differential clock inputs as well as single-ended clock. AC coupling is required between clock drivers and the AFE5803 clock inputs. When single-ended clock is used, CLKM should be tied to ground. Common clock configurations are illustrated in Figure 76. Appropriate termination is recommended to achieve good signal integrity. 44 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com 3.3 V 130 Ω 83 Ω CDCM7005 CDCE72010 3.3 V 0.1 μF AFE CLOCKs 0.1 μF 130 Ω LVPECL (a) LVPECL Configuration 100 Ω CDCE72010 0.1 μF 0.1 μF AFE CLOCKs LVDS (b) LVDS Configuration 0.1μF 0.1μF CLOCK SOURCE 0.1μF AFE CLOCKs 50 Ω 0.1μF (c) Transformer Based Configuration CMOS CLK Driver AFE CMOS CLK CMOS (d) CMOS Configuration S0503-01 Figure 76. Clock Configurations Special considerations should be applied in such a clock distribution network design. In typical ultrasound systems, it is preferred that all clocks are generated from a same clock source, such as CW clocks, audio ADC clocks, RF ADC clock, pulse repetition frequency signal, frame clock and etc. By doing this, interference due to clock asynchronization can be minimized. ADC Reference Circuit The ADC’s voltage reference can be generated internally or provided externally. When the internal reference mode is selected, the REFP/M becomes output pins and should be floated. When 3[15] =1 and 1[13]=1, the device is configured to operate in the external reference mode in which the VREF_IN pin should be driven with a 1.4V reference voltage and REFP/M must be left open. Since the input impedance of the VREF_IN is high, no special drive capability is required for the 1.4V voltage reference Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 45 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com The digital beam-forming algorithm in an ultrasound system relies on gain matching across all receiver channels. A typical system would have about 12 octal AFEs on the board. In such a case, it is critical to ensure that the gain is matched, essentially requiring the reference voltages seen by all the AFEs to be the same. Matching references within the eight channels of a chip is done by using a single internal reference voltage buffer. Trimming the reference voltages on each chip during production ensures that the reference voltages are well-matched across different chips. When the external reference mode is used, a solid reference plane on a printed circuit board can ensure minimal voltage variation across devices. More information on voltage reference design can be found in the document SLYT339. The dominant gain variation in the AFE5803 comes from the VCA gain variation. The gain variation contributed by the ADC reference circuit is much smaller than the VCA gain variation. Hence, in most systems, using the ADC internal reference mode is sufficient to maintain good gain matching among multiple AFE5803s. In addition, the internal reference circuit without any external components achieves satisfactory thermal noise and phase noise performance. POWER MANAGEMENT Power/Performance Optimization The AFE5803 has options to adjust power consumption and meet different noise performances. This feature would be useful for portable systems operated by batteries when low power is more desired. See the electrical characteristics table as well as the typical characteristic plots. Power Management Priority Power management plays a critical role to extend battery life and ensure long operation time. The AFE5803 has fast and flexible power down/up control which can maximize battery life. The AFE5803 can be powered down/up through external pins or internal registers. The following table indicates the affected circuit blocks and priorities when the power management is invoked. The higher priority controls can overwrite the lower priority ones.In the device, all the power down controls are logically ORed to generate final power down for different blocks. Thus, the higher priority controls can cover the lower priority ones. The AFE5803 register settings are maintained when the AFE5803 is in either partial power down mode or complete power down mode. Table 11. Power Management Priority Pin Name Blocks Priority PDN_GLOBAL All High Medium Pin PDN_VCA LNA + VCAT+ PGA Register VCA_PARTIAL_PDN LNA + VCAT+ PGA Low Register VCA_COMPLETE_PDN LNA + VCAT+ PGA Medium Medium Pin PDN_ADC ADC Register ADC_PARTIAL_PDN ADC Low Register ADC_COMPLETE_PDN ADC Medium Register PDN_VCAT_PGA VCAT + PGA Lowest Register PDN_LNA LNA Lowest Partial Power-Up/Down Mode The partial power up/down mode is also called as fast power up/down mode. In this mode, most amplifiers in the signal path are powered down, while the internal reference circuits remain active as well as the LVDS clock circuit, i.e. the LVDS circuit still generates its frame and bit clocks. The partial power down function allows the AFE5803 to be wake up from a low-power state quickly. This configuration ensures that the external capacitors are discharged slowly; thus a minimum wake-up time is needed as long as the charges on those capacitors are restored. The VCA wake-up response is typically about 2 μs or 1% of the power down duration whichever is larger. The longest wake-up time depends on the capacitors connected at INP and INM, as the wake-up time is the time required to recharge the caps to the desired operating voltages. For 0.1μF at INP and 15nF at INM can give a wake-up time of 2.5ms. For larger capacitors this time will be longer. The ADC wake-up time is about 1 μs. Thus the AFE5803 wake-up time is more dependent on the VCA wake-up time. This also assumes that the ADC clock has been running for at least 50 µs before normal operating mode resumes. The power-down time is instantaneous, less than 1.0µs. 46 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com This fast wake-up response is desired for portable ultrasound applications in which the power saving is critical. The pulse repetition frequency of a ultrasound system could vary from 50KHz to 500Hz, while the imaging depth (i.e., the active period for a receive path) varies from 10 μs to hundreds of us. The power saving can be pretty significant when a system’s PRF is low. In some cases, only the VCA would be powered down while the ADC keeps running normally to ensure minimal impact to FPGAs. In the partial power-down mode, the AFE5803 typically dissipates only 26mW/ch, representing an 80% power reduction compared to the normal operating mode. This mode can be set using either pins (PDN_VCA and PDN_ADC) or register bits (VCA_PARTIAL_PDN and ADC_PARTIAL_PDN). Complete Power-Down Mode To achieve the lowest power dissipation of 0.7 mW/CH, the AFE5803 can be placed into a complete power-down mode. This mode is controlled through the registers ADC_COMPLETE_PDN, VCA_COMPLETE_PDN or PDN_GLOBAL pin. In the complete power-down mode, all circuits including reference circuits within the AFE5803 are powered down; and the capacitors connected to the AFE5803 are discharged. The wake-up time depends on the time needed to recharge these capacitors. The wake-up time depends on the time that the AFE5803 spends in shutdown mode. 0.1μF at INP and 15 nF at INM can give a wake-up time close to 2.5ms. VCA TEST MODES The AFE5803 includes multiple test modes to accelerate system development. The ADC test modes have been discussed in the register description section. The VCA has a test mode in which the CH7 and CH8 PGA outputs can be brought. By monitoring these PGA outputs, the functionality of VCA operation can be verified. Some registers are related to this test mode. PGA Test Mode Enable: Reg59[9]; Buffer Amplifier Power Down Reg59[8]; and Buffer Amplifier Gain Control Reg54[4:0]. The PGA outputs are connected to the virtual ground pins of the buffer amplifier through 5 kΩ resistors. The PGA outputs can be monitored at the buffer amplifier outputs when the buffer amplifer is enabled. Note that the signals at the buffer amplifier outputs are attenuated due to the 5KΩ resistors. The attenuation coefficient is RINT/EXT/5kΩ. See Table 7 for the RINT configuration. An alternative way is to measure the PGA outputs directly at the CH8_TEST_OUTM/P and CH7_TEST_OUTM/P when the buffer amplifier is powered down. Based on the buffer amplifier configuration, the registers can be set in different ways: Configuration 1: In this configuration, the test outputs can be monitored at CH7/8_TEST_OUTP/M Reg59[9]=1 ;Test mode enabled Reg59[8]=0 ;Buffer amplifier powered down Configuration 2: In this configuration, the test outputs can be monitored at CH7/8_BUFFER_OUTP/M Reg59[9]=1 ;Test mode enabled Reg59[8]=1 ;Buffer amplifier powered on Reg54[4:0]=10H; Internal feedback 2K resistor enabled. Different values can be used as well Rint/Rext 5 kW PGA CH7/8P CH7/8_TEST_OUTP CH7/8_TEST_OUTM PGA CH7/8M 5 kW CH7/8_BUFFER_OUTM Buffer Amp Rint/Rext CH7/8_BUFFER_OUTP Figure 77. AFE5803 PGA Test Mode Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 47 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com POWER SUPPLY, GROUNDING AND BYPASSING In a mixed-signal system design, power supply and grounding design plays a significant role. The AFE5803 distinguishes between two different grounds: AVSS(Analog Ground) and DVSS(digital ground). In most cases, it should be adequate to lay out the printed circuit board (PCB) to use a single ground plane for the AFE5803. Care should be taken that this ground plane is properly partitioned between various sections within the system to minimize interactions between analog and digital circuitry. Alternatively, the digital (DVDD) supply set consisting of the DVDD and DVSS pins can be placed on separate power and ground planes. For this configuration, the AVSS and DVSS grounds should be tied together at the power connector in a star layout. In addition, optical isolator or digital isolators, such as ISO7240, can separate the analog portion from the digital portion completely. Consequently they prevent digital noise to contaminate the analog portion. Table 11 lists the related circuit blocks for each power supply. Table 12. Supply vs Circuit Blocks POWER SUPPLY GROUND CIRCUIT BLOCKS AVDD (3.3VA) AVSS LNA, attenuator, PGA with current clamp and BPF, reference circuits, PGA test mode buffer, VCA SPI AVDD_5V (5VA) AVSS LNA, reference circuits AVDD_ADC (1.8VA) AVSS ADC analog and reference circuits DVDD (1.8VD) DVSS LVDS and ADC SPI All Bypassing and power supplies for the AFE5803 should be referenced to their corresponding ground planes. All supply pins should be bypassed with 0.1 µF ceramic chip capacitors (size 0603 or smaller). In order to minimize the lead and trace inductance, the capacitors should be located as close to the supply pins as possible. Where double-sided component mounting is allowed, these capacitors are best placed directly under the package. In addition, larger bipolar decoupling capacitors 2.2 µF to 10 µF, effective at lower frequencies) may also be used on the main supply pins. These components can be placed on the PCB in proximity (< 0.5 in or 12.7 mm) to the AFE5803 itself. The AFE5803 has a number of reference supplies needed to be bypassed, such CM_BYP, VHIGH, and VREF_IN. These pins should be bypassed with at least 1µF; higher value capacitors can be used for better low-frequency noise suppression. For best results, choose low-inductance ceramic chip capacitors (size 0402, > 1 µF) and place them as close as possible to the device pins. High-speed mixed signal devices are sensitive to various types of noise coupling. One primary source of noise is the switching noise from the serializer and the output buffer/drivers. For the AFE5803, care has been taken to ensure that the interaction between the analog and digital supplies within the device is kept to a minimal amount. The extent of noise coupled and transmitted from the digital and analog sections depends on the effective inductances of each of the supply and ground connections. Smaller effective inductance of the supply and ground pins leads to improved noise suppression. For this reason, multiple pins are used to connect each supply and ground sets. It is important to maintain low inductance properties throughout the design of the PCB layout by use of proper planes and layer thickness. BOARD LAYOUT Proper grounding and bypassing, short lead length, and the use of ground and power-supply planes are particularly important for high-frequency designs. Achieving optimum performance with a high-performance device such as the AFE5803 requires careful attention to the PCB layout to minimize the effects of board parasitics and optimize component placement. A multilayer PCB usually ensures best results and allows convenient component placement. In order to maintain proper LVDS timing, all LVDS traces should follow a controlled impedance design. In addition, all LVDS trace lengths should be equal and symmetrical; it is recommended to keep trace length variations less than 150mil (0.150 in or 3.81mm). Additional details on BGA PCB layout techniques can be found in the Texas Instruments Application Report MicroStar BGA Packaging Reference Guide (SSYZ015B), which can be downloaded from www.ti.com. 48 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 AFE5803 SLOS763A – JANUARY 2012 – REVISED JANUARY 2012 www.ti.com REVISION HISTORY Changes from Original (January 2012) to Revision A • Page Changed Table 3 Digital HPF –1dB Corner Frequency vs K and Fs ................................................................................. 27 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Link(s): AFE5803 49 PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2012 PACKAGING INFORMATION Orderable Device AFE5803ZCF Status (1) ACTIVE Package Type Package Drawing NFBGA ZCF Pins Package Qty 135 160 Eco Plan (2) Green (RoHS & no Sb/Br) Lead/ Ball Finish SNAGCU MSL Peak Temp (3) Samples (Requires Login) Level-3-260C-168 HR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated