FP5138B Technology BOOST CONVERT CONTROL IC GENERAL DESCRIPTION The FP5138B is a boost topology switching regulator control IC for battery-used applications field. The FP5138B includes a totem-pole single output stage for driving NPN transistor or N-MOS, high precision reference (0.5V) for comparing output voltage with feedback amplifier, an internal dead-time control for controlling the minimum duty cycle, programmable soft start with short circuit protection function and logic level control for operating mode or standby mode. FEATURES ˙Wide supply voltage operating range: 1.8 to 15V ˙Reference voltage precision: 2% ˙Low current consumption: Operation Mode 5.5mA Standby-by Mode 1μA ˙High speed oscillator frequency: 1MHz max. SOP8 ˙Programmable Soft Start function (SS) ˙Short Circuit Protection function(SCP) ˙Totem-pole output with adjustable on/off current (for NPN transistors or n-channel MOSFET) ˙Logic level control stand-by mode function TS S O P 8 ˙Package: SOP8/TSSOP8/MSOP8 TYPICAL APPLICATION ˙Digital Camera MS O P 8 ˙PDA ˙Portable Equipment Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P1/FP5138B FP5138B Technology FUNCTIONAL BLOCK DIAGRAM 3 7 Reference voltage supply Sawtooth wave oscillator 0.8V 0.1V 1.25V 1 PWM Comp. 36kΩ 36 + + + + Error Amp. 500KΩ 0.5V 5 0.1V 30 30kΩ Output drive control circuit DTC 0.6V 0.22V 8 Soft start & SCP circuit 6 2 4 PIN DESCRIPTION MARK VIEW Name No. FB 1 8 2 7 3 - 4 FP5138 1 L Website: http://www.feeling-tech.com.tw 6 5 SCP 2 VCC BR/CTL OUT GND 3 4 5 6 OSC 7 COMP 8 I/O Description I Error amplifier inverting input pin Connected a capacitor I Soft start and SCP function pin P IC power supply I Output current setting and control pin O Totem-pole output P IC ground Capacitor and resistor connected for I the frequency of oscillation O Error amplifier compensation output Rev0.7 August 17, 2006 P2/FP5138B Technology FP5138B ORDER INFORMATION Part Number FP5138BD-LF FP5138BDR-LF FP5138BW-LF FP5138BWR-LF FP5138BT-LF FP5138BTR-LF FP5138BX-LF FP5138BXR-LF Operating Temperature -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C Package SOP8 SOP8 TSSOP8 TSSOP8 MSOP8 MSOP8 SOP8-EXPOSED PAD SOP8-EXPOSED PAD Description Tube Tape & Reel Tube Tape & Reel Tube Tape & Reel Tube Tape & Reel IC DATE CODE DISTINGUISH FP5138 - L Lead Free Lot Number Mass Production Version Per Half Month Year FOR EXAMPLE: January February March A (Front Half Month), B (Last Half Month) C, D E, F ------------And so on Lot Number is the last two numbers For Example: A3 3 11 C6 2 Lot Number Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P3/FP5138B FP5138B Technology ABSOLUTE MAXIMUM RATINGS Power supply voltage--------------------------------------------------------------------------- +15V Output source current-------------------------------------------------------------------------- -50mA Output sink current----------------------------------------------------------------------------- +50mA Allowable dissipation SOP8 Ta≦+25℃------------------------------------------------------------------------- 570mW MSOP8 Ta≦+25℃------------------------------------------------------------------------ 400mW TSSOP8 Ta≦+25℃------------------------------------------------------------------------- 400mW SOP8-EXPOSED PAD 600mW Ta≦+25℃------------------------------------------------- Operating temperature---------------------------------------------------------------------- -10℃～+85℃ Storage temperature------------------------------------------------------------------------ -55℃～+125℃ Junction breakdown Temperature--------------------------------------------------------- +125℃ SOP8 Lead Temperature (soldering, 10 sec) ------------------------------------------- +260℃ TSSOP8 Lead Temperature (soldering, 10 sec) --------------------------------------- +260℃ MSOP8 Lead Temperature (soldering, 10 sec) ---------------------------------------- +260℃ 260℃/sec 260℃ -1.2℃/sec +0.23℃/sec 210℃ 180℃ +3.4℃/sec 25℃ 15s 60s 190s 280s IR Re-flow Soldering Curve Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P4/FP5138B FP5138B Technology DC ELECTRICAL CHARACTERISTICS(Ta=25℃,VCC=+2V, unless otherwise noted) Under Voltage Lock-Out section (U.V.L.O.) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT VLOW -- - - 0.9 V VUPPER -- 1.1 1.3 1.5 V SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT ISS VSCP= 0V -1.5 -1.0 -0.7 μA VSST -- 0.8 0.9 1.0 V SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Input source current ISCP VSCP= 0V -1.5 -1.0 -0.7 μA S.C.P. threshold voltage VSCP -- 0.7 0.8 0.9 V SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT f RT=3.0KΩ,CT=270pF 400 500 600 KHz Δf / ΔV VCC=2V to 15V - 2 10 % Δf / ΔT Ta = 0℃to 85℃ - 5 - % TEST CONDITIONS MIN. TYP. MAX. UNIT 75 - 85 % Low threshold voltage Upper threshold voltage Soft Start section (S.S.) PARAMETER Input source current Soft start threshold voltage Short Circuit Protection section (S.C.P.) PARAMETER Oscillator section PARAMETER Oscillation frequency Frequency change with voltage Frequency change with temperature Idle Period Adjustment section PARAMETER Maximum duty cycle SYMBOL TDUTY RT=3.0kΩ, CT=270pF, VFB=0.8V Total device section PARAMETER Stand-by current Average supply current Website: http://www.feeling-tech.com.tw SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT ISTANDBY Pin4 is open or VCC - - 1 μA IAVE RB=390Ω,VCC=0~20V - 5.0 10 mA Rev0.7 August 17, 2006 P5/FP5138B FP5138B Technology DC ELECTRICAL CHARACTERISTICS (Cont.) Error Amplifier section PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Input threshold voltage VFB VCOMP=450mV 495 500 505 mV VT change with voltage ΔVFB / ΔV VCC=2V to 15V - 5 20 mV VT change with temperature ΔVFB / ΔT Ta = -10℃to 85℃ - 1 - % Input bias current IB -- -1.0 -0.2 1.0 μA Voltage Gain Av -- - 100 - V/V Frequency bandwidth BW Av=0 dB - 6 - MHz Output voltage Positive VPOS -- 0.78 0.87 - Swing Negative VNEG -- - 0.05 0.2 - -40 -24 μA 24 40 - μA MIN. TYP. MAX. UNIT 1.0 1.2 - V 0.8 1.0 - V - 0.1 0.2 V - 0.1 0.2 V Output source current Output sink current ISOURCE ISINK VCOMP=450mV V Output section PARAMETER SYMBOL Output high voltage VOH1 Output high voltage VOH2 Output saturation voltage VOL1 Output saturation voltage VOL2 Output source current TEST CONDITIONS RB=390Ω, IO=-15mA RB=750Ω, IO=-10mA, VCC= 1.8V RB=390Ω, IO=15mA RB=750Ω, IO=10mA, VCC= 1.8V IOSOURCE RB=390Ω, Vo=0.9V - -40 -20 mA IOSINK RB=390Ω, Vo=0.3V 30 40 - mA -- 20 30 40 kΩ SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT VBR RB=390Ω 0.15 0.22 0.3 V RB - 300 390 5000 Ω Input off condition IOFF -- -20 - 0 μA Input on condition ION -- - - -45 μA Pin current range IBR -- -1.8 - -0.1 mA Output sink current Internal pull-down resistor RO Output Current Setting / Control section PARAMETER Pin voltage Output current setting resistance Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P6/FP5138B FP5138B Technology TYPICAL CHARACTERISTICS Supply Voltage VS Input Threshold Voltage Supply Voltage VS Supply Current 12 1.2 Supply Current (mA) 10 Input Threshold Voltage Vt (V) Ta=25℃ RB=390Ω 8 6 4 2 0 0 8 4 12 16 0.4 0.2 0 0 8 4 Figure 2 10 5 0 -5 -10 25 50 75 1.2 VCC=2V RB=390Ω Ta=25℃ 1.0 0.8 0.6 0.4 0.2 0 100 0 -10 600 -40 -50 BR/CTL Pin Current VS Output Source Current -60 VCC=2V RB=390Ω Ta=25℃ 500 Output Source Current Iout (mA) Low Level Output Voltage Vout (V) -30 Figure 4 Low Level Output 400 300 200 100 40 -20 High Level Output Current Iout (mA) Figure 3 20 20 High Level Output Ambient Temperature Ta (℃) 0 16 Figure 1 VCC=2V 0 12 Supply Voltage (V) High Level Output Voltage Vout (V) Input Threshold Voltage Variation △V/V(%) 0.6 Supply Voltage (V) 30 0 0.8 20 Ambient Temperature VS Input Threshold Voltage Variation Ratio -15 -25 Ta=25℃ 1.0 60 80 100 Low Level Output Current Iout (mA) Figure 5 Website: http://www.feeling-tech.com.tw VCC=2V Vout=0.9V Ta=25℃ -50 -40 -30 -20 -10 0 0 -0.4 -0.8 -1.2 -1.6 -2.0 BR/CTL Pin Current IBR (mA) Figure 6 Rev0.7 August 17, 2006 P7/FP5138B FP5138B Technology TYPICAL CHARACTERISTICS (Cont.) BR/CTL Pin Current VS BR/CTL Pin Voltage BR/CTL Pin Current VS Supply Current 6.0 VCC=2V Ta=25℃ 500 Supply Current ICC (mA) BR/CTL Pin Voltage VBR (mV) 600 400 300 200 4.0 3.0 2.0 1.0 100 0 VCC=2V Ta=25℃ 5.0 0 -0.4 -0.8 -1.2 -1.6 0 -2.0 -20 0 -40 BR/CTL Pin Current IBR(mA) Frequency Variation Ration △f／f(%) Oscillator Frequency fosc (Hz) Triangle Oscillator Frequency VS Timing Resistance VCC=2V Ta=25℃ CT = 100 pF 100K CT = 1000 pF 10K CT = 10000 pF 2K 1K 4K 10K -80 -100 Figure 8 Figure 7 1M -60 BR/CTL Pin Current IBR (μA) 40K 100K Supply Voltage VS Frequency Variation Ration 15 CT=270PF RT=3.0KΩ Ta=25℃ 10 5 0 -5 -10 -15 400K 1M 0 4 8 12 16 20 Supply Voltage VCC (V) Timing Resistor Rt (Ω) Figure 10 Figure 9 Frequency Variation △f／f(%) 30 10 Ambient Temperature VS Frequency Variation Ration VCC=2V CT=270PF RT=3.0LΩ 5 0 - 5 -10 -15 -25 0 25 50 75 100 Ambient Temperature Ta (℃) Figure 11 Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P8/FP5138B FP5138B Technology TIMING WAVEFORM COMP Pin Voltage Reference Input For Short Circuit Detection Comparator Idle Period Setting Voltage Soft Start Setting Voltage OUT Pin Waveforms SCP Pin Waveforms Soft Start ts ON Power Supply Control SW OFF Output Short Circuit tpe Output Short Circuit Short Circuit Detection FP5138B Timing Diagram Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P9/FP5138B FP5138B Technology DETAILED DESCRIPTION Voltage reference A 1.25V regulator operating from VCC is used to power the internal circuitry of the FP5138B. An internal resistive divider provides 0.5V reference for the error amplifier, Soft-start (typ. 0.9V) and SCP (typ. 0.8V) circuits. Error amplifier The error amplifier compares a sample of the dc-dc converter output voltage to the 0.5V reference and generates an error signal for the PWM comparator. Output voltage of dc-dc converter is setting with the resistor divider using the following expression (see fig12): R1 Vout = 1 + ∗ 0.5 R2 VOUT R1 Error Amplifier 1 36K R2 0.5V 500 FP5138B 8 C1 Figure 12. Error Amplifier with Feedback resistance divider Oscillator The oscillator frequency can be set between 20KHz and 500KHz by connecting a resistor and a capacitor at OSC pin of FP5138B to ground. The oscillator frequency can be determined by using the graph shown in Figure 9. The oscillator output is a sawtooth wave with a minimum value of approximately 0.1V and a maximum value of approximately 0.8V. The PWM comparator compares the oscillator voltage with error amplifier output voltage; internal DTC voltage (typ. 0.6V) and soft start setting voltage. When the sawtooth wave voltage is low than above three-output voltage, the output of FP5138B is high (Turn on NPN transistor or NMOS). Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P10/FP5138B Technology FP5138B Under voltage lockout (UVLO) The under voltage lockout circuits turn the output off and whenever the supply voltage drops too low (approximately 0.9V at 25℃) for proper operation. A hysteresis voltage of 200mV eliminates false triggering on noise and chattering. Soft Start/ Short-circuit protection (S.S. / S.C.P.) The soft start is functional after power on, and the interval of soft start time is determined by a capacitor connected to SCP pin (pin 2). When soft start function finished, the internal soft start voltage is setting high, but external SCP pin is setting low in order to change to short circuit detection / protection function. The time of soft start is following expression: Tss = 0.35 ∗ C [µF ] The short circuit protection is functional due to a heavy loading drop and output of error amplifier (COMP pin) is maintain a VPOS (typ. 0.9V), the capacitor is charged until SCP threshold voltage (typ. 0.8V), then FP5138B output is disable (internal pull-low) and the capacitor is discharged to low. The time of short circuit protection is following expression: Tscp = 0.8 ∗ C [µF ] Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P11/FP5138B FP5138B Technology Output transistor The FP5138B has a totem-pole transistor with a 40mA source/sink current rating to drive an external NPN transistor or NMOS directly. The driving current capability depends on a resistor R that is connected to BR/CTL pin (Pin4) of FP5138B. (see fig. 14) FP5138B 4 BR/CTL R Control Q1 Figure 13. Output transistor driving control circuit BR/CTL pin can also use to control the output of FP5138B for disable or enable function of system. Control Pin Q1 BR/CTL Pin Output Transistor Function Mode Low Off Open Disable Stand-by High On Bias Current Enable Operation Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P12/FP5138B FP5138B Technology APPLICATION NOTE (1) L1 20uH SCD34 D1 Vin +12V Vout +24V/1A IC1 R1 COMP SCP OSC VCC GND R2 47k 1% C1 0.027uF R3 0 C7 C2 2 FB Q2 1 BR/CTL OUT C8 C4 0.1uF 3 220uF/25V 100uF/35V FP5138B C5 R4 0.1uF R6 1k R5 3k Q1 3904 C6 1k 1% 470pF ON/OFF Socket Vin R7 4.7k 1 2 SW1 Figure 14. DC12V to DC24V Boost Regulator L1 20uH C9 Vin +2.5V ~ +6V SCD34 D1 Vout +3.3V IC1 10u R1 COMP SCP OSC VCC GND R2 5.6k 1% C1 0.027uF 2 FB R3 0 C7 Q2 L2 20uH C2 1 BR/CTL OUT C8 MOSFET N GDS 0.1uF 3 220uF/25V C4 100uF/35V FP5138B C5 R4 0.1uF 1k Q1 3904 R6 R5 3k C6 1k 1% 470pF ON/OFF Socket Vin 1 2 R7 4.7k SW1 Figure 15. DC2.5V~DC6V to DC3.3V SEPIC Regulator Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P13/FP5138B FP5138B Technology APPLICATION NOTE (2) Q1 Vin +3.3V L1 Pmos AP2305 33uH Vout +1.8V 2 1 3 R1 IC1 1 R2 10k FB 8 COMP R3 C1 100 C2 C 2 3 SCP OSC VCC GND 7 0.027uF C3 C4 330uF 6 D1 R4 4 5 BR/CTL OUT C5 0.1uF SCD34 Q2 NPN 3904 1k FP5138B R5 R6 499 3.9k R7 C6 Q3 NPN 3904 3.3k 270pF ON/OFF Socket Vin R8 4.7k 1 2 SW1 Figure 16. DC3.3V to DC1.8V Buck Regulator D1 PNP BEC 3906 1 BAT54S/SOT_0 NPN BEC 3904 D2 C3 1uF R1 390 C4 1uF 1 C5 1uF R4 2 30k R6 5.1k R7 2.2k C6 1uF Vout3 +17V PMOS AN2305 2 3 2 BAT54S/SOT_0 R2 2.2k R3 5.6k Q1 Q2 C2 0.1uF 3 1 3 C1 0.1uF Q3 Vout2 -6.8V R5 30k 3 2 D3 R8 6.8k 1 1 D4 C8 1uF TL431 2 3 TL431 R9 L1 L2 33uH D5 SCD34 Vin Q4 NPN 3904 33uH 300k C9 1uF R10 5.1k Vout1 +9V IC1 R11 2 3 FB COMP SCP OSC VCC GND BR/CTL OUT 8 R12 7 51k 1% C10 0.027uF 6 R13 0 4 C16 0.1uF C7 0.1uF R14 1k 5 Q1 NMOS AN2304 1 C13 3 C12 220uF/6.3V C11 2 1 C14 100uF 0.1uF C15 100uF FP5138B R15 Q6 NPN 3904 R16 3k C17 3k 1% 470pF ON/OFF Socket Vin 1 2 R17 4.7k SW1 Figure 17. Charge Pump DC-DC Converter Circuits Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P14/FP5138B FP5138B Technology APPLICATION NOTE (3) R9 R8 56K 1.8K R10 R11 33K 5.1K V2 FB V3 R12 3.3K D2 BAT54HT1 L2 33uH +15V V1 (R9+R8)=17.48*R12 0.66*(R8+R9)=(R10+R11) + C8 100uF/25V + C9 47uF/16V D3 VCC L1 F1 T1 18uH 4 FUSE C2 104 L3 6 V2 33uH +5V 5 C1 R7 + C7 470pF 330uF 7 + 1 C10 100uF/16V + C11 47uF/16V BAT54RCLT1 8 2 D4 D6 8.2 9 L4 U1 3 C4 0.47uF CTL 4 SCP Cosc VCC GND CTL OUT COMP 8 +3.3V 10 + 7 C5 0.1uF CLS12 C6 6 5 1 R6 FP5138B R5 220 3 0 C12 100uF/16V + C13 47uF/16V BAT54RCLT1 3 2 33uH V3 COMP L5 Q3 AP2304 33uH V4 D5 -7.5V BAT54HT1 C14 100uF/16V C15 + SCP FB 2 1 47uF/16V + R1 Q2 2N3904 ON / OFF R4 33K C16 1nF R2 10K C3 270pF R3 3K Figure 18. Flyback Multi-output DC-DC Converter Circuits Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P15/FP5138B FP5138B Technology PACKAGE OUTLINE SOP8 0.16typ 0.015X45 H E 0.008typ. 0.050typ θ° D A L A1 SEATING PLANE 0.004max SYMBOLS MIN MAX A 1.346 1.752 A1 0.101 0.254 D 4.800 4.978 E 3.810 3.987 H 5.791 6.197 L 0.406 1.270 θ° 0 8 UNIT:MM NOTE: 1. JEDEC OUTLINE:MS-012 AA 2. DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS.MOLD FLASH,PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED .15mm (.0.06in) PER SIDE 3. DIMENSIONS “E” DOES NOT INCLUDE INTER-LEAD FLASH,OR PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED .25mm (.0.10in) PER SIDE. Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P16/FP5138B FP5138B Technology MSOP8 5 E E1 8 “A” 1 4 0.30 0.65 BSC GAUEGE PLANE θ° 0.25 D SEATING PLANE 0.15 TYP L A2 A1 A L1 0.05 SYMBOLS MIN MAX A - 1.10 A1 0.00 0.15 A2 0.75 0.95 D 3.00 BSC E 4.90 BSC E1 3.00 BSC L 0.40 L1 θ° 0.80 0.95 REF 0 8 UNIT:MM NOTE: 1.JEDEC OUTLINE:MO-187 AA 2.DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS.MOLD FLASH,PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE 3.DIMENSIONS “E1” DOES NOT INCLUDE INTERLEAD FLASH,OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.25 PER SIDE. 4.DIMENSIONS “0.22” DOES NOT INCLUDE DAMBAR PROTRUSIONS.ALLOWABLE DAMBAR PROTRUSIONS SHALL BE 0.08 MM TOTAL IN EXCESS OF THE ‘0.22’ DIMENSION AT MAXIMUM MATERIAL CONDITION.DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OF THE FOOT.MINIMIM SPAC BETWEEN PROTRUSION AND ADJACENT LEAD IS 0.07MM. 5.DIMENSIONS “D” AND ‘E1’ TO BE DETERMINED AT DATUM PLANE H Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P17/FP5138B FP5138B Technology TSSOP8 SYMBOLS MIN NOR MAX A - - 1.20 A1 0.05 - 0.15 A2 0.96 1.01 1.06 D 2.90 3.00 3.10 E 6.40 BSC E1 4.30 4.40 4.50 L 0.45 0.60 0.75 θ° 0 - 8 UNIT:MM NOTE: 1.JEDEC OUTLINE:MO-187 AA 2.DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS.MOLD FLASH,PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE 3.DIMENSIONS “E1” DOES NOT INCLUDE INTERLEAD FLASH,OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.25 PER SIDE. 4.DIMENSIONS “0.22” DOES NOT INCLUDE DAMBAR PROTRUSIONS.ALLOWABLE DAMBAR PROTRUSIONS SHALL BE 0.08 MM TOTAL IN EXCESS OF THE ‘0.22’ DIMENSION AT MAXIMUM MATERIAL CONDITION.DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OF THE FOOT.MINIMIM SPAC BETWEEN PROTRUSION AND ADJACENT LEAD IS 0.07MM. 5.DIMENSIONS “D” AND ‘E1’ TO BE DETERMINED AT DATUM PLANE H Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P18/FP5138B FP5138B Technology SOP8-EXPOSED PAD . SYMBOLS MIN MAX A 1.346 1.752 A1 0.101 0.254 D 4.800 4.978 E 3.810 3.987 H 5.791 6.197 L 0.406 1.270 θ° 0 8 UNIT:MM THERMALLY ENHANCED DIMENSISONS PAD SIZE E1 D1 A 2.057 REF 2.057 REF A1 2.184 REF 2.971 REF UNIT:MM NOTE: 1.JEDEC OUTLINE:N/A 2.DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS.MOLD FLASH,PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED .15mm (.0.06in) PER SIDE 3.DIMENSIONS “E” DOES NOT INCLUDE INTER-LEAD FLASH,OR PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED .25mm (.0.10in) PER SIDE. Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P19/FP5138B FP5138B Technology PACKING SPECIFICATIONS BOX DIMENSION TUBE INSIDE BOX AND CARTON 100mm FTC Logo 220mm FTC Logo 630mm BOX LABEL 640mm BOX LABEL 190mm 380mm INSIDE BOX TUBE CARTON TAPE AND REEL INSIDE BOX AND CARTON 380mm 362mm 365mm 342mm 230mm FTC label 50mm CARTON LABEL FTC Logo Tape & Reel Carton PACKING QUANTITY SPECIFICATIONS SOP 8 MSOP8 TSSOP8 100 80 160 SOP8-EXPOSED PAD SOP 8 100 EA/TUBE EA/TUBE EA/TUBE MSOP8 TSSOP8 SOP8-EXPOSED PAD 2500 EA / REEL EA/TUBE 100 TUBES / INSIDE BOX 4 INSIDE BOXES / CARTON 4 INSIDE BOXES / CARTON LABEL SPECIFICATIONS Tapping & Reel Feeling Technology Corp. Product： FP5138B Lot No ：A3311C62 D/C ： 4Xx-XXL Q'ty ： ◎～◎ 無鉛 Lead Free Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P20/FP5138B FP5138B Technology CARTON Feeling Technology Corp. Product Type: FP5138B Lot No: A3311C62 Date Code: 4Xx-XXL Package Type: SOP-8L Marking Type: Laser Total Q'ty: 無鉛 Lead Free 10,000 SOP8 CARRIER TAPE DIMENSIONS APPLICATION SOP8 W 12.0 +0.3 -0.1 P E F D D1 8.0±0.1 1.75±0.1 5.5±0.1 1.55±0.1 1.5+0.25 APPLICATION P0 P1 AD B0 K0 t SOP8 4.0±0.1 2.0±0.1 6.4±0.1 5.20±0.1 2.1±0.10 0.30±0.013 Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P21/FP5138B FP5138B Technology REEL DIMENISIONS APPLICATION SOP8 MATERIAL PLASTIC REEL (WHILE) Website: http://www.feeling-tech.com.tw A B C D T1 T2 330±0.1 62±1.5 12.75+0.15 2+0.6 12.4+0.2 2.0+0.2 Rev0.7 August 17, 2006 P22/FP5138B FP5138B Technology MSOP8 CARRIER TAPE DIMENSIONS APPLICATION MSOP8 W 12.0±3 P 8.0 E 1.75±1.0 F 5.5±0.5 D 1.5 +0.1 D1 1.50 APPLICATION P0 P1 AD B0 K0 t MSOP8 4.0±0.1 2.0±0.5 4.20 3.30 1.20 0.30±0.5 (mm) Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P23/FP5138B FP5138B Technology REEL DIMENISIONS APPLICATION MSOP8 MATERIAL PLASTIC REEL (WHILE) Website: http://www.feeling-tech.com.tw A B C D T1 T2 330±1 62±1.5 12.75+0.15 2±0.15 12.4+0.2 16.8-0.4 Rev0.7 August 17, 2006 P24/FP5138B FP5138B Technology TSSOP8 CARRIER TAPE DIMENSIONS APPLICATION TSSOP8 W 12.0±0.3 P 8.00 E 1.75±1.0 F 5.5±0.05 D 1.5 +0.1 D1 1.50 APPLICATION P0 P1 AD B0 K0 t TSSOP8 4.00 2.00±0.05 4.20 3.40 1.30 0.30±0.5 (mm) Website: http://www.feeling-tech.com.tw Rev0.7 August 17, 2006 P25/FP5138B FP5138B Technology REEL DIMENISIONS APPLICATION TSSOP8 MATERIAL PLASTIC REEL (WHILE) Website: http://www.feeling-tech.com.tw A B C D T1 330 100 13.0+0.5 2±0.5 12.5 Rev0.7 August 17, 2006 P26/FP5138B FP5138B Technology SOP8-EXPOSED PAD CARRIER TAPE DIMENSIONS APPLICATION W 12.0 SOP8 +0.3 -0.1 P E F D D1 8.0±0.1 1.75±0.1 5.5±0.1 1.55±0.1 1.5+0.25 APPLICATION P0 P1 AD B0 K0 t SOP8 4.0±0.1 2.0±0.1 6.4±0.1 5.20±0.1 2.1±0.10 0.30±0.013 REEL DIMENISIONS APPLICATION SOP8 MATERIAL PLASTIC REEL (WHILE) Website: http://www.feeling-tech.com.tw A B C D T1 T2 330±0.1 62±1.5 12.75+0.15 2+0.6 12.4+0.2 2.0+0.2 Rev0.7 August 17, 2006 P27/FP5138B