M1815B BOOST CONVERT CONTROL IC GENERAL DESCRIPTION The M181 5 B is a boost topology switching regulator control IC for battery-used applications field. The M1815 B includes a totem-pole single output stage for driving NPN transistor or N-MOS, high precision reference (0.5V) for comparing output voltage with feedback amplifier, an internal dead-time control for controlling the minimum duty cycle, programmable soft start with short circuit protection function and logic level control for operating mode or standby mode. FEATURES ˙Wide supply voltage operating range: 1.8 to 15V ˙Reference voltage precision: 2% ˙Low current consumption: Operation Mode 5.5mA Standby-by Mode 1µA ˙High speed oscillator frequency: 1MHz max. SOP8 ˙Programmable Soft Start function (SS) ˙Short Circuit Protection function(SCP) ˙Totem-pole output with adjustable on/off current (for NPN transistors or n-channel MOSFET) ˙Logic level control stand-by mode function TS S OP 8 ˙Package: SOP8/TSSOP8/MSOP8 TYPICAL APPLICATION ˙Digital Camera MS O P 8 ˙PDA ˙Portable Equipment -1- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC FUNCTIONAL BLOCK DIAGRAM 3 7 Reference voltage supply Sawtooth wave oscillator 0.8V 0.1V 1.25V 1 PWM Comp. 36 36kΩ + + + + Error Amp. 500KΩ 0.5V 5 0.1V 30 30kΩ Output drive control circuit DTC 0.6V 0.22V 8 Soft start & SCP circuit 6 2 4 PIN DESCRIPTION MARK VIEW Name No. FB 1 8 SCP 2 2 7 VCC BR/CTL OUT GND 3 4 5 6 OSC 7 COMP 8 3 - 4 L -2- M1815B 1 6 5 I/O Description I Error amplifier inverting input pin Connected a capacitor I Soft start and SCP function pin P IC power supply I Output current setting and control pin O Totem-pole output P IC ground Capacitor and resistor connected for I the frequency of oscillation O Error amplifier compensation output TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC ORDER INFORMATION Part Number M1815BD-LF M1815BDR-LF M1815BW -LF M1815BWR-L F M1815BT -LF M1815BTR-LF M1815BX-LF M1815BXR-LF Operating Temperature -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C -10°C ~ +85°C Package SOP8 SOP8 TSSOP8 TSSOP8 MSOP8 MSOP8 SOP8-EXPOSED PAD SOP8-EXPOSED PAD Description Tube Tape & Reel Tube Tape & Reel Tube Tape & Reel Tube Tape & Reel IC DATE CODE DISTINGUISH M1815B - L Lead Free Lot Number Mass Production Version Per Half Month Year FOR EXAMPLE: January February March A (Front Half Month), B (Last Half Month) C, D E, F ------------And so on Lot Number is the last two numbers For Example: A2201C 62 Lot Number -3- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC ABSOLUTE MAXIMUM RATINGS Power supply voltage--------------------------------------------------------------------------- +15V Output source current------------------------------------------------------------------------- -50mA Output sink current------------------------------------------------------------------------------ +50mA Allowable dissipation SOP8 Ta≦+25℃-------------------------------------------------------------------- 570Mw MSOP8 Ta≦+25℃------------------------------------------------------------------- 400mW TSSOP8 Ta≦+25℃-------------------------------------------------------------------- 400mW SOP8-EXPOSED PAD Ta≦+25℃--------------------------------------------- 600mW Operating temperature--------------------------------------------------------------- -10℃∼+85℃ Storage temperature------------------------------------------------------------------ -55℃∼+125℃ SOP8 Lead Temperature (soldering, 10 sec) ------------------------------------------+260℃ TSSOP8 Lead Temperature (soldering, 10 sec) --------------------------------------+260℃ MSOP8 Lead Temperature (soldering, 10 sec) ---------------------------------------+260℃ 260℃/sec 260℃ -1.2℃/sec +0.23℃/sec 210℃ 180℃ +3.4℃/sec 25℃ 15s -4- 60s 190s TEL:0755-86276964 MOB:13570814546 280s Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC DC ELECTRICAL CHARACTERISTICS(Ta=25℃,VCC=+2V, unless otherwise noted) Under Voltage Lock-Out section (U.V.L.O.) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Low threshold voltage VLOW -- - - 0.9 V Upper threshold voltage VUPPER -- 1.1 1.3 1.5 V PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Input source current ISS VSCP= 0V -1.5 -1.0 -0.7 μA Soft start threshold voltage VSST -- 0.8 0.9 1.0 V Soft Start section (S.S.) Short Circuit Protection section (S.C.P.) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Input source current ISCP VSCP= 0V -1.5 -1.0 -0.7 μA S.C.P. threshold voltage VSCP -- 0.7 0.8 0.9 V PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Oscillation frequency f RT=3.0KΩ,CT=270pF 400 500 600 KHz ∆f / ∆V VCC=2V to 15V - 2 10 % ∆f / ∆T Ta = 0℃to 85℃ - 5 - % PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Maximum duty cycle TDUTY 75 - 85 % Oscillator section Frequency change with voltage Frequency change with temperature Idle Period Adjustment section RT=3.0kΩ, CT=270pF, VFB=0.8V Total device section -5- PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Stand-by current ISTANDBY Pin4 is open or VCC - - 1 µA Average supply current IAVE RB=390Ω,VCC=0~20V - 5.0 10 mA TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC DC ELECTRICAL CHARACTERISTICS (Cont.) Error Amplifier section PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Input threshold voltage VFB VCOMP=450mV 495 500 505 mV VT change with voltage ∆VFB / ∆V VCC=2V to 15V - 5 20 mV VT change with temperature ∆VFB / ∆T Ta = -10℃to 85℃ - 1 - % Input bias current IB -- -1.0 -0.2 1.0 µA Voltage Gain Av -- - 100 - V/V Frequency bandwidth BW Av=0 dB - 6 - MHz Output voltage Positive VPOS -- 0.78 0.87 - Swing Negative VNEG -- - 0.05 0.2 - -40 -24 µA 24 40 - µA MIN. TYP. MAX. UNIT 1.0 1.2 - V 0.8 1.0 - V - 0.1 0.2 V - 0.1 0.2 V Output source current ISOURCE Output sink current ISINK VCOMP=450mV V Output section PARAMETER SYMBOL Output high voltage VOH1 Output high voltage VOH2 Output saturation voltage VOL1 Output saturation voltage VOL2 Output source current IOSOURCE RB=390Ω, Vo=0.9V - -40 -20 mA Output sink current IOSINK RB=390Ω, Vo=0.3V 30 40 - mA -- 20 30 40 kΩ Internal pull-down resistor RO TEST CONDITIONS RB=390Ω, IO=-15mA RB=750Ω, IO=-10mA, VCC= 1.8V RB=390Ω, IO=15mA RB=750Ω, IO=10mA, VCC= 1.8V Output Current Setting / Control section -6- PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT Pin voltage VBR RB=390Ω 0.15 0.22 0.3 V Input off condition IOFF -- -20 - 0 µA Input on condition ION -- - - -45 µA Pin current range IBR -- -1.8 - -0.1 mA TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC TYPICAL CHARACTERISTICS Supply Voltage VS Input Threshold Voltage Supply Voltage VS Supply Current 12 1.2 Supply Current (mA) 10 Input Threshold Voltage Vt (V) Ta=25℃ RB=390Ω 8 6 4 2 0 0 8 4 12 16 0.4 0.2 0 0 8 4 Figure 2 10 5 0 -5 -10 25 50 75 1.2 VCC=2V RB=390Ω Ta=25℃ 1.0 0.8 0.6 0.4 0.2 0 100 0 -10 -40 -50 BR/CTL Pin Current VS Output Source Current -60 VCC=2V RB=390Ω Ta=25℃ 500 Output Source Current Iout (mA) Low Level Output Voltage Vout (V) 600 400 300 200 100 60 80 100 VCC=2V Vout=0.9V Ta=25℃ -50 -40 -30 -20 -10 0 0 Low Level Output Current Iout (mA) Figure 5 -7- -30 Figure 4 Low Level Output 40 -20 High Level Output Current Iout (mA) Figure 3 20 20 High Level Output Ambient Temperature Ta (℃) 0 16 Figure 1 VCC=2V 0 12 Supply Voltage (V) High Level Output Voltage Vout (V) Input Threshold Voltage Variation △V/V(%) 0.6 Supply Voltage (V) 30 0 0.8 20 Ambient Temperature VS Input Threshold Voltage Variation Ratio -15 -25 Ta=25℃ 1.0 TEL:0755-86276964 MOB:13570814546 -0.4 -0.8 -1.2 -1.6 -2.0 BR/CTL Pin Current IBR (mA) Figure 6 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC TYPICAL CHARACTERISTICS (Cont.) BR/CTL Pin Current VS BR/CTL Pin Voltage BR/CTL Pin Current VS Supply Current 6.0 VCC=2V Ta=25℃ 500 Supply Current ICC (mA) BR/CTL Pin Voltage VBR (mV) 600 400 300 200 100 0 VCC=2V Ta=25℃ 5.0 4.0 3.0 2.0 1.0 0 -0.4 -0.8 -1.2 -1.6 0 -2.0 -20 0 -40 BR/CTL Pin Current IBR(mA) 100K CT = 1000 pF 10K CT = 10000 pF 4K 10K 40K 100K f(%) CT = 100 pF 15 Frequency Variation Ration △f Oscillator Frequency fosc (Hz) Triangle Oscillator Frequency VS Timing Resistance VCC=2V Ta=25℃ 2K 1K -80 -100 Figure 8 Figure 7 1M -60 BR/CTL Pin Current IBR (μA) 10 Supply Voltage VS Frequency Variation Ration CT=270PF RT=3.0KΩ Ta=25℃ 5 0 -5 -10 -15 400K 1M 0 4 8 12 16 20 Supply Voltage VCC (V) Timing Resistor Rt (Ω) Figure 10 Figure 9 Frequency Variation △f f(%) 30 10 Ambient Temperature VS Frequency Variation Ration VCC=2V CT=270PF RT=3.0LΩ 5 0 - 5 -10 -15 -25 0 25 50 75 100 Ambient Temperature Ta (℃) Figure 11 -8- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC TIMING WAVEFORM COMP Pin Voltage Reference Input For Short Circuit Detection Comparator Idle Period Setting Voltage Soft Start Setting Voltage OUT Pin Waveforms SCP Pin Waveforms ON Power Supply Control SW OFF Soft Start ts Output Short Circuit tpe Output Short Circuit Short Circuit Detection M1815B T iming Diagram -9- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC DETAILED DESCRIPTION Voltage reference A 1.25V regulator operating from VCC is used to power the internal circuitry of the M1815B . An internal resistive divider provides 0.5V reference for the error amplifier, Soft-start (typ. 0.9V) and SCP (typ. 0.8V) circuits. Error amplifier The error amplifier compares a sample of the dc-dc converter output voltage to the 0.5V reference and generates an error signal for the PWM comparator. Output voltage of dc-dc converter is setting with the resistor divider using the following expression (see fig12): R1 Vout = 1 + ∗ 0.5 R2 VOUT R1 Error Amplifier 1 36K R2 0.5V 500 M1815B 8 C1 Figure 12. Error Amplifier with Feedback resistance divider Oscillator The oscillator frequency can be set between 20KHz and 500KHz by connecting a resistor and a capacitor at OSC pin of M1815 B to ground. The oscillator frequency can be determined by using the graph shown in Figure 9. The oscillator output is a sawtooth wave with a minimum value of approximately 0.1V and a maximum value of approximately 0.8V. The PWM comparator compares the oscillator voltage with error amplifier output voltage; internal DTC voltage (typ. 0.6V) and soft start setting voltage. When the sawtooth wave voltage is low than above three-output voltage, the output of M1815 B is high (Turn on NPN transistor or NMOS). -10- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC Under voltage lockout (UVLO) The under voltage lockout circuits turn the output off and whenever the supply voltage drops too low (approximately 0.9V at 25℃) for proper operation. A hysteresis voltage of 200mV eliminates false triggering on noise and chattering. Soft Start/ Short-circuit protection (S.S. / S.C.P.) The soft start is functional after power on, and the interval of soft start time is determined by a capacitor connected to SCP pin (pin 2). When soft start function finished, the internal soft start voltage is setting high, but external SCP pin is setting low in order to change to short circuit detection / protection function. The time of soft start is following expression: Tss = 0.35 ∗ C [µF ] The short circuit protection is functional due to a heavy loading drop and output of error amplifier (COMP pin) is maintain a VPOS (typ. 0.9V), the capacitor is charged until SCP threshold voltage (typ. 0.8V), then M1815 B output is disable (internal pull-low) and the capacitor is discharged to low. The time of short circuit protection is following expression: Tscp = 0.8 ∗ C [µF ] -11- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC Output transistor The M1815 B has a totem-pole transistor with a 40mA source/sink current rating to drive an external NPN transistor or NMOS directly. The driving current capability depends on a resistor R that is connected to BR/CTL pin (Pin4) of M1815B . (see fig. 14) M1815B 4 BR/CTL R Control Q1 Figure 13. Output transistor driving control circuit BR/CTL pin can also use to control the output of M1815 B for disable or enable function of system. Control Pin Q1 BR/CTL Pin Output Transistor Function Mode Low Off Open Disable Stand-by High On Bias Current Enable Operation -12- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC APPLICATION NOTE (1) L1 20uH Vin +12V SCD34 D1 Vout +24V/1A IC1 R1 COMP SCP OSC VCC GND R2 47k 1% C1 0.027uF R3 0 C7 3 1k R5 3k Q1 3904 C4 0.1uF R4 0.1uF 1 2 C8 M1815B C5 ON/OFF Socket Vin Q2 1 BR/CTL OUT 220uF/25V C2 2 FB 100uF/35V R6 C6 1k 1% 470pF R7 4.7k SW1 Figure 14. DC12V to DC24V Boost Regulator L1 20uH C9 Vin +2.5V ~ +6V SCD34 D1 Vout +3.3V IC1 10u R1 COMP SCP OSC VCC GND R2 5.6k 1% C1 0.027uF 2 FB R3 0 C7 Q2 1 BR/CTL OUT L2 20uH C2 C8 MOSFET N GDS 0.1uF 3 220uF/25V C5 0.1uF R4 1k Q1 3904 M1815B C4 100uF/35V R6 R5 3k C6 1k 1% 470pF ON/OFF Socket Vin 1 2 R7 4.7k SW1 Figure 15. DC2.5V~DC6V to DC3.3V SEPIC Regulator -13- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC APPLICATION NOTE (2) Q1 Vin +3.3V 33uH Vout +1.8V 2 1 3 L1 Pmos AP2305 R1 IC1 1 FB 8 COMP R3 100 C2 C 2 3 C5 0.1uF 4 SCP OSC VCC GND 0.027uF 7 C3 C4 330uF 6 5 BR/CTL OUT R2 10k C1 D1 R4 SCD34 Q2 NPN 3904 1k M1815B R5 R6 499 3.9k R7 C6 Q3 NPN 3904 3.3k 270pF ON/OFF Socket Vin R8 4.7k 1 2 SW1 Figure 16. DC3.3V to DC1.8V Buck Regulator D1 PNP BEC 3906 BAT54S/SOT_0 C2 0.1uF 3 D2 1 C3 1uF BAT54S/SOT_0 R2 2.2k NPN BEC 3904 C4 1uF R1 390 R4 2 30k R6 5.1k R7 2.2k C6 1uF Vout3 +17V PMOS AN2305 3 2 1 C5 1uF R3 5.6k Q1 Q2 2 1 3 C1 0.1uF Q3 Vout2 -6.8V R5 30k 3 2 D3 R8 6.8k 1 D4 1 C8 1uF TL431 2 3 TL431 R9 L1 33uH L2 D5 SCD34 Vin 33uH 300k FB COMP SCP OSC VCC GND R11 8 R12 7 51k 1% C10 0.027uF 6 R13 0 C16 0.1uF C7 0.1uF R14 1k BR/CTL OUT 1 2 Q1 NMOS AN2304 1 M1815B Q6 NPN 3904 ON/OFF Socket Vin 5 C13 3 4 C12 220uF/6.3V R16 3k C11 2 2 3 R10 5.1k Vout1 +9V IC1 1 Q4 NPN 3904 C9 1uF C17 470pF C14 100uF 0.1uF C15 100uF R15 3k 1% R17 4.7k SW1 Figure 17. Charge Pump DC-DC Converter Circuits -14- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC APPLICATION NOTE (3) R9 R8 56K 1.8K R10 R11 33K 5.1K V2 FB V3 R12 3.3K 4 C1 C2 104 C7 470pF R7 + 330uF 6 5 8 2 L4 C4 0.47uF 3 CTL 4 SCP Cosc VCC GND CTL OUT C5 0.1uF 7 CLS12 C6 6 Q3 AP2304 1 5 R6 M1815B R5 220 33uH 0 +3.3V C12 100uF/16V + + C13 47uF/16V BAT54RCLT1 3 2 COMP C11 47uF/16V L5 V4 33uH -7.5V 2 SCP FB V3 10 3 + D4 9 COMP 33uH BAT54RCLT1 U1 8 C9 47uF/16V C10 100uF/16V + 1 1 L3 7 D6 8.2 + D3 T1 18uH C8 100uF/25V D5 BAT54HT1 C14 100uF/16V C15 + L1 FUSE 33uH +15V + Ｖ ５ ＋ F1 L2 V1 ２ Ｖ VCC D2 BAT54HT1 (R9+R8)=17.48*R12 0.66*(R8+R9)=(R10+R11) 47uF/16V + R1 Q2 2N3904 ON / OFF 33K C16 1nF R2 10K R4 C3 270pF R3 3K Figure 18. Flyback Multi-output DC-DC Converter Circuits -15- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC PACKAGE OUTLINE SOP8 0.16typ 0.015X45 H E 0.008typ. 0.050typ θ° D A L A1 SEATING PLANE 0.004max SYMBOLS MIN MAX A 1.346 1.752 A1 0.101 0.254 D 4.800 4.978 E 3.810 3.987 H 5.791 6.197 L 0.406 1.270 θ° 0 8 UNIT:MM NOTE: 1. JEDEC OUTLINE:MS-012 AA 2. DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS.MOLD FLASH,PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED .15mm (.0.06in) PER SIDE 3. DIMENSIONS “E” DOES NOT INCLUDE INTER-LEAD FLASH,OR PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED .25mm (.0.10in) PER SIDE. -16- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC MSOP8 5 E E1 8 “A” 1 4 0.30 0.65 BSC GAUEGE PLANE θ° 0.25 D SEATING PLANE 0.15 TYP L A2 A1 A L1 0.05 SYMBOLS MIN MAX A - 1.10 A1 0.00 0.15 A2 0.75 0.95 D 3.00 BSC E 4.90 BSC E1 3.00 BSC L 0.40 L1 θ° 0.80 0.95 REF 0 8 UNIT:MM NOTE: 1.JEDEC OUTLINE:MO-187 AA 2.DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS.MOLD FLASH,PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE 3.DIMENSIONS “E1” DOES NOT INCLUDE INTERLEAD FLASH,OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.25 PER SIDE. 4.DIMENSIONS “0.22” DOES NOT INCLUDE DAMBAR PROTRUSIONS.ALLOWABLE DAMBAR PROTRUSIONS SHALL BE 0.08 MM TOTAL IN EXCESS OF THE ‘0.22’ DIMENSION AT MAXIMUM MATERIAL CONDITION.DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OF THE FOOT.MINIMIM SPAC BETWEEN PROTRUSION AND ADJACENT LEAD IS 0.07MM. 5.DIMENSIONS “D” AND ‘E1’ TO BE DETERMINED AT DATUM PLANE H -17- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC TSSOP8 SYMBOLS MIN NOR MAX A - - 1.20 A1 0.05 - 0.15 A2 0.96 1.01 1.06 D 2.90 3.00 3.10 E 6.40 BSC E1 4.30 4.40 4.50 L 0.45 0.60 0.75 θ° 0 - 8 UNIT:MM NOTE: 1.JEDEC OUTLINE:MO-187 AA 2.DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS.MOLD FLASH,PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE 3.DIMENSIONS “E1” DOES NOT INCLUDE INTERLEAD FLASH,OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.25 PER SIDE. 4.DIMENSIONS “0.22” DOES NOT INCLUDE DAMBAR PROTRUSIONS.ALLOWABLE DAMBAR PROTRUSIONS SHALL BE 0.08 MM TOTAL IN EXCESS OF THE ‘0.22’ DIMENSION AT MAXIMUM MATERIAL CONDITION.DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OF THE FOOT.MINIMIM SPAC BETWEEN PROTRUSION AND ADJACENT LEAD IS 0.07MM. 5.DIMENSIONS “D” AND ‘E1’ TO BE DETERMINED AT DATUM PLANE H -18- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC SOP8-EXPOSED PAD . SYMBOLS MIN MAX A 1.346 1.752 A1 0.101 0.254 D 4.800 4.978 E 3.810 3.987 H 5.791 6.197 L 0.406 1.270 θ° 0 8 UNIT:MM THERMALLY ENHANCED DIMENSISONS PAD SIZE E1 D1 A 2.057 REF 2.057 REF A1 2.184 REF 2.971 REF UNIT:MM NOTE: 1.JEDEC OUTLINE:N/A 2.DIMENSIONS “D” DOES NOT INCLUDE MOLD FLASH,PROTRUSIONS OR GATE BURRS.MOLD FLASH,PROTRUSIONS AND GATE BURRS SHALL NOT EXCEED .15mm (.0.06in) PER SIDE 3.DIMENSIONS “E” DOES NOT INCLUDE INTER-LEAD FLASH,OR PROTRUSIONS. INTER-LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED .25mm (.0.10in) PER SIDE. -19- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC PACKING SPECIFICATIONS BOX DIMENSION TUBE INSIDE BOX AND CARTON 380mm FTC Logo 365mm 630mm 230mm BOX LABEL CARTON LABEL 190mm FTC Logo INSIDE BOX TUBE CARTON TAPE AND REEL INSIDE BOX AND CARTON 380mm 362mm 365mm 342mm 230mm FTC label 50mm CARTON LABEL FTC Logo Tape & Reel Carton PACKING QUANTITY SPECIFICATIONS SOP 8 MSOP8 TSSOP8 100 80 160 EA/TUBE EA/TUBE EA/TUBE SOP8-EXPOSED PAD SOP 8 100 EA/TUBE MSOP8 TSSOP8 SOP8-EXPOSED PAD 2500 EA / REEL 100 TUBES / INSIDE BOX 4 INSIDE BOXES / CARTON 4 INSIDE BOXES / CARTON LABEL SPECIFICATIONS Tapping & Reel Mitsubishi Technology Corp. Product： M1815B Lot No ：A2201C62 D/C ： 4Xx-XXL Q'ty ： ◎∼◎ 無鉛 Lead Free -20- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC CARTON Mitsubishi Technology Corp. Product Type: M181 5B Lot No: A2201C62 Date Code: 4Xx-XXL Package Type: SOP-8L Marking Type: Laser Total Q'ty: 無鉛 Lead Free 10,000 SOP8 CARRIER TAPE DIMENSIONS APPLICATION SOP8 W 12.0 +0.3 -0.1 P E F D D1 8.0±0.1 1.75±0.1 5.5±0.1 1.55±0.1 1.5+0.25 APPLICATION P0 P1 AD B0 K0 t SOP8 4.0±0.1 2.0±0.1 6.4±0.1 5.20±0.1 2.1±0.10 0.30±0.013 -21- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC REEL DIMENISIONS APPLICATION SOP8 -22- MATERIAL PLASTIC REEL (WHILE) A B C D T1 T2 330±0.1 62±1.5 12.75+0.15 2+0.6 12.4+0.2 2.0+0.2 TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC MSOP8 CARRIER TAPE DIMENSIONS APPLICATION MSOP8 W 12.0±3 P E F D D1 8.0 1.75±1.0 5.5±0.5 1.5+0.1 1.50 APPLICATION P0 P1 AD B0 K0 t MSOP8 4.0±0.1 2.0±0.5 4.20 3.30 1.20 0.30±0.5 (mm) -23- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC REEL DIMENISIONS APPLICATION MSOP8 -24- MATERIAL PLASTIC REEL (WHILE) A B C D T1 T2 330±1 62±1.5 12.75+0.15 2±0.15 12.4+0.2 16.8-0.4 TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC TSSOP8 CARRIER TAPE DIMENSIONS APPLICATION TSSOP8 W 12.0±0.3 P E F D D1 8.00 1.75±1.0 5.5±0.05 1.5+0.1 1.50 APPLICATION P0 P1 AD B0 K0 t TSSOP8 4.00 2.00±0.05 4.20 3.40 1.30 0.30±0.5 (mm) -25- TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC REEL DIMENISIONS APPLICATION TSSOP8 -26- MATERIAL PLASTIC REEL (WHILE) A B C D T1 330 100 13.0+0.5 2±0.5 12.5 TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006 M1815B BOOST CONVERT CONTROL IC SOP8-EXPOSED PAD CARRIER TAPE DIMENSIONS APPLICATION SOP8 W 12.0 +0.3 -0.1 P E F D D1 8.0±0.1 1.75±0.1 5.5±0.1 1.55±0.1 1.5+0.25 APPLICATION P0 P1 AD B0 K0 t SOP8 4.0±0.1 2.0±0.1 6.4±0.1 5.20±0.1 2.1±0.10 0.30±0.013 REEL DIMENISIONS APPLICATION SOP8 -27- MATERIAL PLASTIC REEL (WHILE) A B C D T1 T2 330±0.1 62±1.5 12.75+0.15 2+0.6 12.4+0.2 2.0+0.2 TEL:0755-86276964 MOB:13570814546 Rev0.6 April 20, 2006