Micrel, Inc. SY10EL11V 5V/3.3V 1:2 DIFFERENTIAL FANOUT BUFFER PrecisionSY100EL11V Edge® SY10EL11V SY100EL11V FEATURES ■ ■ ■ ■ ■ ■ ■ ■ 3.3V and 5V power supply options 265ps propagation delay 5ps skew between outputs High bandwidth output transitions Internal 75Ký input pull-down resistors Replaces SY10/100EL11 Improved output waveform characteristics Available in 8-pin SOIC package Precision Edge® DESCRIPTION The SY10/100EL11V are 1:2 differential fanout gates. These devices are functionally similar to the E111A/L devices, with higher performance capabilities. Having within-device skews and output transition times significantly improved over the E111A/L, the EL11V is ideally suited for those applications which require the ultimate in AC performance. The differential inputs of the EL11V employ clamping circuitry to maintain stability under open input conditions. If the inputs are left open (pulled to VEE), the Q outputs will go LOW. PIN NAMES Pin D Q0, Q1 Function Data Inputs Data Outputs Precision Edge is a registered trademark of Micrel, Inc. M9999-052610 [email protected] or (408) 955-1690 1 Rev.: I Amendment: /0 Issue Date: May 2010 SY10EL11V SY100EL11V Micrel, Inc. PACKAGE/ORDERING INFORMATION Ordering Information(1) Q0 Q0 1 8 2 7 V CC D Part Number Package Type 3 6 D 4 5 V EE 8-Pin SOIC (Z8-1) Z8-1 Commercial HEL11V Sn-Pb Z8-1 Commercial HEL11V Sn-Pb SY100EL11VZC Z8-1 Commercial XEL11V Sn-Pb SY100EL11VZCTR Z8-1 Commercial XEL11V Sn-Pb SY10EL11VZI Z8-1 Industrial HEL11V Sn-Pb SY10EL11VZITR Z8-1 Industrial HEL11V Sn-Pb SY100EL11VZI Z8-1 Industrial XEL11V Sn-Pb SY100EL11VZITR(2) Z8-1 Industrial XEL11V Sn-Pb SY10EL11VZG(3) Z8-1 Industrial HEL11V with Pb-Free Pb-Free bar-line indicator NiPdAu SY10EL11VZGTR(2, 3) Z8-1 Industrial HEL11V with Pb-Free Pb-Free bar-line indicator NiPdAu SY100EL11VZG(3) Z8-1 Industrial XEL11V with Pb-Free Pb-Free bar-line indicator NiPdAu SY100EL11VZGTR(2, 3) Z8-1 Industrial XEL11V with Pb-Free Pb-Free bar-line indicator NiPdAu Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-052610 [email protected] or (408) 955-1690 Lead Finish SY10EL11VZCTR(2) (2) Q1 Package Marking SY10EL11VZC (2) Q1 Operating Range 2 SY10EL11V SY100EL11V Micrel, Inc. ABSOLUTE MAXIMUM RATINGS(1) Symbol Rating Value Unit VCC Power Supply Voltage (VEE = 0) +6.0 to 0 V VEE Power Supply Voltage (VCC = 0) –6.0 to 0 V VIN Input Voltage (VCC = 0V, VIN not more negative than VEE) Input Voltage (VEE = 0V, VIN not more positive than VCC) –6.0 to 0 +6.0 to 0 V V IOUT Output Current –Continuous –Surge 50 100 mA TLEAD Lead Temperature Range (soldering, 20sec.) +260 °C TA Operating Temperature Range –40 to +85 °C Tstore Storage Temperature Range –65 to +150 °C θJA Thermal Resistance (Junction-to-Ambient) –Still Air –500lfpm 160 109 °C/W °C/W θJC Thermal Resistance (Junction-to-Case) 39 °C/W ESD Mil Std. 883 Human Body Model, All Pins >1.5k V Note 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability. 10K Series DC ELECTRICAL CHARACTERISTICS(1) VCC = 3.3V +10%; VEE = 0V TA = –40°C Symbol Parameter Min. TA = 0°C Max. Min. Max. TA = +25°C Min. TA = +85°C Max. Min. Max. Unit VOH Output HIGH Voltage –1080 –890 –1020 –840 –980 –810 –910 –720 mV VOL Output LOW Voltage –1950 –1650 –1950 –1630 –1950 –1630 –1950 –1595 mV VIH Input HIGH Voltage –1230 –890 –1170 –840 –1130 –810 –1060 –720 mV VIL Input LOW Voltage –1950 –1500 –1950 –1480 –1950 –1480 –1950 –1445 mV IIH Input HIGH Current — 150 — 150 — 150 — 150 µA IIL Input LOW Current 0.5 — 0.5 — 0.5 — 0.3 — µA 100K series dc electrical characteristics(2) VCC = 3.3V +10%; VEE = 0V TA = –40°C Symbol Parameter Min. Typ. TA = 0°C to +85°C Max. Min. Typ. Max. Unit VOH VOL Output HIGH Voltage Output LOW Voltage –1085 –1005 –880 –1025 –955 –880 mV –1830 –1695 –1555 –1810 –1705 –1620 VIH Input HIGH Voltage(3) –1165 — –880 –1165 — –880 mV VIL Input LOW Voltage –1810 — –1475 –1810 — –1475 mV (4) Conditions VIN = VIH(Max) or VIL(Min) IIH Input HIGH Current — — 150 — — 150 µA IIL Input LOW Current M9999-052610 [email protected] or (408) 955-1690 0.5 — — 0.5 3 — — µA VIN = VIL(Min) SY10EL11V SY100EL11V Micrel, Inc. 10K Series DC ELECTRICAL CHARACTERISTICS(1) VCC = 5.0V +10%; VEE = 0V TA = –40°C Symbol Parameter Min. TA = 0°C Max. Min. Max. TA = +25°C Min. TA = +85°C Max. Min. Max. Unit VOH Output HIGH Voltage –1080 –890 –1020 –840 –980 –810 –910 –720 mV VOL Output LOW Voltage –1950 –1650 –1950 –1630 –1950 –1630 –1950 –1595 mV VIH Input HIGH Voltage –1230 –890 –1170 –840 –1130 –810 –1060 –720 mV VIL Input LOW Voltage –1950 –1500 –1950 –1480 –1950 –1480 –1950 –1445 mV IIH Input HIGH Current — 150 — 150 — 150 — 150 µA IIL Input LOW Current 0.5 — 0.5 — 0.5 — 0.3 — µA 100K series dc electrical characteristics(2) VCC = 5.0V +10%; VEE = 0V TA = –40°C Symbol Parameter Min. Typ. TA = 0°C to +85°C Max. Min. Typ. Max. Unit VOH VOL Output HIGH Voltage Output LOW Voltage –1085 –1005 –880 –1025 –955 –880 mV –1830 –1695 –1555 –1810 –1705 –1620 VIH Input HIGH Voltage(3) –1165 — –880 –1165 — –880 mV VIL Input LOW Voltage –1810 — –1475 –1810 — –1475 mV (4) Conditions VIN = VIH(Max) or VIL(Min) IIH Input HIGH Current — — 150 — — 150 µA IIL Input LOW Current M9999-052610 [email protected] or (408) 955-1690 0.5 — — 0.5 4 — — µA VIN = VIL(Min) SY10EL11V SY100EL11V Micrel, Inc. 10K Series DC ELECTRICAL CHARACTERISTICS(1) VCC = 0V; VEE = -3.3V +10% TA = –40°C Symbol Parameter Min. TA = 0°C Max. Min. Max. TA = +25°C Min. TA = +85°C Max. Min. Max. Unit VOH Output HIGH Voltage –1080 –890 –1020 –840 –980 –810 –910 –720 mV VOL Output LOW Voltage –1950 –1650 –1950 –1630 –1950 –1630 –1950 –1595 mV VIH Input HIGH Voltage –1230 –890 –1170 –840 –1130 –810 –1060 –720 mV VIL Input LOW Voltage –1950 –1500 –1950 –1480 –1950 –1480 –1950 –1445 mV IIH Input HIGH Current — 150 — 150 — 150 — 150 µA IIL Input LOW Current 0.5 — 0.5 — 0.5 — 0.3 — µA 100K series dc electrical characteristics(2) VCC = 0V; VEE = -3.3V +10% TA = –40°C Symbol Parameter Min. Typ. TA = 0°C to +85°C Max. Min. Typ. Max. Unit VOH VOL Output HIGH Voltage Output LOW Voltage –1085 –1005 –880 –1025 –955 –880 mV –1830 –1695 –1555 –1810 –1705 –1620 VIH Input HIGH Voltage(3) –1165 — –880 –1165 — –880 mV VIL Input LOW Voltage –1810 — –1475 –1810 — –1475 mV (4) Conditions VIN = VIH(Max) or VIL(Min) IIH Input HIGH Current — — 150 — — 150 µA IIL Input LOW Current M9999-052610 [email protected] or (408) 955-1690 0.5 — — 0.5 5 — — µA VIN = VIL(Min) SY10EL11V SY100EL11V Micrel, Inc. 10K Series DC ELECTRICAL CHARACTERISTICS(1) VCC = 0V; VEE = -5.0V +10% TA = –40°C Symbol Parameter Min. TA = 0°C Max. Min. Max. TA = +25°C Min. TA = +85°C Max. Min. Max. Unit VOH Output HIGH Voltage –1080 –890 –1020 –840 –980 –810 –910 –720 mV VOL Output LOW Voltage –1950 –1650 –1950 –1630 –1950 –1630 –1950 –1595 mV VIH Input HIGH Voltage –1230 –890 –1170 –840 –1130 –810 –1060 –720 mV VIL Input LOW Voltage –1950 –1500 –1950 –1480 –1950 –1480 –1950 –1445 mV IIH Input HIGH Current — 150 — 150 — 150 — 150 µA IIL Input LOW Current 0.5 — 0.5 — 0.5 — 0.3 — µA 100K series dc electrical characteristics(2) VCC = 0V; VEE = -5.0V +10% TA = –40°C Symbol Parameter Min. Typ. TA = 0°C to +85°C Max. Min. Typ. Max. Unit VOH VOL Output HIGH Voltage Output LOW Voltage –1085 –1005 –880 –1025 –955 –880 mV –1830 –1695 –1555 –1810 –1705 –1620 VIH Input HIGH Voltage(3) –1165 — –880 –1165 — –880 mV VIL Input LOW Voltage –1810 — –1475 –1810 — –1475 mV (4) Conditions VIN = VIH(Max) or VIL(Min) IIH Input HIGH Current — — 150 — — 150 µA IIL Input LOW Current 0.5 — — 0.5 — — µA VIN = VIL(Min) Notes: 1. 10EL circuits are designed to meet the DC specifications shown in the table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained. Outputs are terminated through a 50Ω resistor to –2.0V except where otherwise specified on the individual data sheets. 2. This table replaces the three tables traditionally seen in ECL 100K data books. The same DC parameter values at VEE = –4.5V now apply across the full VEE range of –4.2V to –5.5V. Outputs are terminated through a 50Ω resistor to –2.0V except where otherwise specified on the individual data sheets. 100K circuits are designed to meet the DC specifications shown in the table where transverse airflow greater than 500lfpm is maintained. 3. Guaranteed HIGH Signal for all Inputs. 4. Guaranteed LOW Signal for all Inputs. M9999-052610 [email protected] or (408) 955-1690 6 SY10EL11V SY100EL11V Micrel, Inc. AC ELECTRICAL CHARACTERISTICS(1) VEE = VEE (Min.) to VEE (Max.); VCC = GND TA = –40°C Symbol Parameter TA = 0°C TA = +25°C TA = +85°C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit tPLH tPHL Propagation Delay to Output D 135 260 385 185 260 335 190 265 340 215 290 365 ps tskew Within-Device Skew(2) Duty Cycle Skew(3) — — 5 5 — — — — 5 5 20 20 — — 5 5 20 20 — — 5 5 20 20 ps tJITTER Random Clock Jitter (RMS) — — — — — — — 0.6 — — — — ps VPP Minimum Input Swing 150 — — 150 — — 150 — — 150 — — mV VCMR Common Mode Range(5) –1.3 — –0.4 –1.4 — –0.4 –1.4 — –0.4 –1.4 — –0.4 V tr tf Output Rise/Fall Times Q (20% to 80%) 100 225 350 100 225 350 100 225 350 100 225 350 ps (4) Notes: 1. Parametric values specified at: 2. Within-device skew defined as identical transitions on similar paths through a device. 3. Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device. 4. Minimum input swing for which AC parameters are guaranteed. The device has a DC gain of 40. 5. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP min. and 1V. The lower end of the CMR range varies 1:1 with VEE. The numbers in the spec table assume a nominal VEE = –3.3V. Note for PECL operation, the VCMR (min) will be fixed at 3.3V – |VCMR (min)|. M9999-052610 [email protected] or (408) 955-1690 10/100EL11V Series: -3.0V to -5.5V. 7 SY10EL11V SY100EL11V Micrel, Inc. 8-PIN SOIC .150" wide (Z8-1) Package Notes: Note 1. Package meets Level 1 moisture sensitivity. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA tel + 1 (408) 944-0800 fax + 1 (408) 474-1000 web http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2003 Micrel, Incorporated. M9999-052610 [email protected] or (408) 955-1690 8