ADS7846 ADS 7846 AD S784 6 ® AD S784 6 SBAS125H – SEPTEMBER 1999 – REVISED JANUARY 2005 TOUCH SCREEN CONTROLLER FEATURES DESCRIPTION ● SAME PINOUT AS ADS7843 The ADS7846 is a next-generation version to the industry standard ADS7843 4-wire touch screen controller. The ADS7846 is 100% pin-compatible with the existing ADS7843, and drops into the same socket. This allows for easy upgrade of current applications to the new version. Only software changes are required to take advantage of the added features of direct battery measurement, temperature measurement, and touch-pressure measurement. The ADS7846 also has an on-chip 2.5V reference that can be used for the auxiliary input, battery monitor, and temperature measurement modes. The reference can also be powered down when not used to conserve power. The internal reference operates down to 2.7V supply voltage while monitoring the battery voltage from 0V to 6V. ● 2.2V TO 5.25V OPERATION ● INTERNAL 2.5V REFERENCE ● ● ● ● DIRECT BATTERY MEASUREMENT (0V to 6V) ON-CHIP TEMPERATURE MEASUREMENT TOUCH-PRESSURE MEASUREMENT QSPITM/SPITM 3-WIRE INTERFACE ● AUTO POWER-DOWN ● TSSOP-16, SSOP-16, QFN-16, AND VFBGA-48 PACKAGES APPLICATIONS ● ● ● ● ● ● The low-power consumption of < 0.75mW (typ at 2.7V, reference off), high speed (up to 125kHz clock rate), and onchip drivers make the ADS7846 an ideal choice for batteryoperated systems such as personal digital assistants (PDAs) with resistive touch screens, pagers, cellular phones, and other portable equipment. The ADS7846 is available in the small TSSOP-16, SSOP-16, QFN-16, and VFBGA-48 packages and is specified over the –40°C to +85°C temperature range. PERSONAL DIGITAL ASSISTANTS PORTABLE INSTRUMENTS POINT-OF-SALE TERMINALS PAGERS TOUCH SCREEN MONITORS CELLULAR PHONES US Patent No. 6246394 QSPI and SPI are registered trademarks of Motorola. PENIRQ +VCC X+ Temperature Sensor X– SAR Y+ ADS7846 DOUT Y– BUSY Comparator 6-Channel MUX VBAT Serial Data Out CDAC CS DCLK Battery Monitor DIN AUX Internal 2.5V Reference VREF Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. Copyright © 1999-2005, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ABSOLUTE MAXIMUM RATINGS(1) +VCC to GND ........................................................................ –0.3V to +6V Analog Inputs to GND ............................................ –0.3V to +VCC + 0.3V Digital Inputs to GND ............................................. –0.3V to +VCC + 0.3V Power Dissipation .......................................................................... 250mW Maximum Junction Temperature ................................................... +150°C Operating Temperature Range ........................................ –40°C to +85°C Storage Temperature Range ......................................... –65°C to +150°C Lead Temperature (soldering, 10s) ............................................... +300°C NOTE: (1) Stresses above these ratings can cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION(1) PRODUCT MAXIMUM INTEGRAL LINEARITY ERROR (LSB) ADS7846E PACKAGE-LEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER ±2 SSOP-16 DBQ –40°C to +85°C ADS7846E " " " " " ADS7846E ADS7846E/2K5 ±2 TSSOP-16 PW –40°C to +85°C ADS7846N " " " " " " " " " " ADS7846N ADS7846N/2K5 ADS7846N/2K5G4 ADS7846I ±2 VFBGA-48 GQC –40°C to +85°C ADS7846 ADS7846IGQCR ADS7846I ±2 QFN-16 RGV –40°C to +85°C ADS7846 " " " " " ADS7846IRGVT ADS7846IRGVR " ADS7846N " " " NOTE: (1) For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet, or see the TI web site at www.ti.com. 2 ADS7846 www.ti.com SBAS125H ELECTRICAL CHARACTERISTICS At TA = –40°C to +85°C, +VCC = +2.7V, VREF = 2.5V internal voltage, fSAMPLE = 125kHz, fCLK = 16 • fSAMPLE = 2MHz, 12-bit mode, and digital inputs = GND or +VCC, unless otherwise noted. ADS7846E PARAMETER ANALOG INPUT Full-Scale Input Span Absolute Input Range CONDITIONS MIN Positive Input-Negative Input Positive Input Negative Input 0 –0.2 –0.2 Capacitance Leakage Current SYSTEM PERFORMANCE Resolution No Missing Codes Integral Linearity Error Offset Error Gain Error Noise Power-Supply Rejection SAMPLING DYNAMICS Conversion Time Acquisition Time Throughput Rate Multiplexer Settling Time Aperture Delay Aperture Jitter Channel-to-Channel Isolation SWITCH DRIVERS On-Resistance Y+, X+ Y–, X– Drive Current(2) BATTERY MONITOR Input Voltage Range Input Impedance Sampling Battery Battery Monitor Off Accuracy TEMPERATURE MEASUREMENT Temperature Range Resolution Accuracy DIGITAL INPUT/OUTPUT Logic Family Logic Levels, Except PENIRQ VIH VIL VOH VOL PENIRQ VOL Data Format POWER-SUPPLY REQUIREMENTS +VCC(5) Quiescent Current Power Dissipation MAX UNITS VREF +VCC + 0.2 +0.2 V V V pF µA 25 0.1 12 11 External VREF Including Internal VREF ±2 ±6 ±4 70 70 12 3 125 500 30 100 100 VIN = 2.5Vp-p at 50kHz 5 6 Duration 100ms REFERENCE OUTPUT Internal Reference Voltage Internal Reference Drift Quiescent Current REFERENCE INPUT Range Input Impedance TYP 50 2.45 2.50 15 500 +VCC 1 V GΩ 250 Ω 6.0 V +2 +3 kΩ GΩ % % 10 1 –2 –3 –40 Differential Method(3) TEMP0(4) Differential Method(3) TEMP0(4) Ω Ω mA V ppm/°C µA 0.5 External VREF = 2.5V Internal Reference CLK Cycles CLK Cycles kHz ns ns ps dB 2.55 1.0 SER/DFR = 0, PD1 = 0, Internal Reference Off Internal Reference On Bits Bits LSB(1) LSB LSB µVrms dB +85 1.6 0.3 ±2 ±3 °C °C °C °C °C CMOS | IIH | ≤ +5µA | IIL | ≤ +5µA IOH = –250µA IOL = 250µA +VCC • 0.7 –0.3 +VCC • 0.8 +VCC + 0.3 +0.8 TA = 0°C to +85°C, 50kΩ Pull-Up 0.4 V V V 0.8 V 3.6 5.25 650 3 V V µA µA µA µA 1.8 mW +85 °C Straight Binary Specified Performance Operating Range Internal Reference Off Internal Reference On fSAMPLE = 12.5kHz Power-Down Mode with CS = DCLK = DIN = +VCC +VCC = +2.7V TEMPERATURE RANGE Specified Performance 2.7 2.2 280 780 220 –40 NOTES: (1) LSB means least significant bit. With VREF equal to +2.5V, one LSB is 610µV. (2) Ensured by design, but not tested. Exceeding 50mA source current may result in device degradation. (3) Difference between TEMP0 and TEMP1 measurement. No calibration necessary. (4) Temperature drift is –2.1mV/°C. (5) ADS7846 operates down to 2.2V. ADS7846 SBAS125H www.ti.com 3 PIN CONFIGURATION Top View Top View SSOP, TSSOP VFBGA CS DCLK +VCC 1 16 DCLK X+ 2 15 CS Y+ 3 14 DIN X– 4 13 BUSY Y– 5 GND 6 ADS7846 1 2 DIN 3 BUSY DOUT 4 5 6 A NC 7 NC B NC C NC NC NC NC NC NC NC NC PENIRQ +VCC 12 DOUT 11 PENIRQ +VCC +VCC D NC NC NC NC NC E NC NC NC NC NC F NC NC NC NC NC NC X+ VBAT 7 10 +VCC AUX 8 9 VREF VREF AUX Y+ G NC NC X– Y– GND GND VBAT BUSY 1 DIN 2 13 VREF 14 +VCC 15 PENIRQ QFN 16 DOUT Top View NC 12 AUX 11 VBAT ADS7846 8 Y– X– 9 7 4 Y+ DCLK 6 GND X+ 10 5 3 +VCC CS PIN DESCRIPTION 4 SSOP AND TSSOP PIN # VFBGA PIN # QFN PIN # NAME 1 2 3 4 5 6 7 8 9 10 11 12 B1 and C1 D1 E1 G2 G3 G4 and G5 G6 E7 D7 C7 B7 A6 5 6 7 8 9 10 11 12 13 14 15 16 +VCC X+ Y+ X– Y– GND VBAT AUX VREF +VCC PENIRQ DOUT 13 14 15 A5 A4 A3 1 2 3 BUSY DIN CS 16 A2 4 DCLK DESCRIPTION Power Supply X+ Position Input Y+ Position Input X– Position Input Y– Position Input Ground Battery Monitor Input Auxiliary Input to ADC Voltage Reference Input/Output Digital I/O Power Supply Pen Interrupt. Open anode output (requires 10kΩ to 100kΩ pull-up resistor externally). Serial Data Output. Data is shifted on the falling edge of DCLK. This output is high impedance when CS is high. Busy Output. This output is high impedance when CS is high. Serial Data Input. If CS is low, data is latched on rising edge of DCLK. Chip Select Input. Controls conversion timing and enables the serial input/output register. CS high = power-down mode (ADC only). External Clock Input. This clock runs the SAR conversion process and synchronizes serial data I/O. ADS7846 www.ti.com SBAS125H TYPICAL CHARACTERISTICS At TA = +25°C, +VCC = +2.7V, VREF = External +2.5V, fSAMPLE = 125kHz, and fCLK = 16 • fSAMPLE = 2MHz, unless otherwise noted. POWER-DOWN SUPPLY CURRENT vs TEMPERATURE 400 140 350 120 Supply Current (nA) Supply Current (µA) SUPPLY CURRENT vs TEMPERATURE 300 250 200 150 100 80 60 40 100 20 –40 –20 0 20 60 40 80 100 –40 –20 0 20 40 60 80 100 Temperature (°C) Temperature (°C) SUPPLY CURRENT vs +VCC MAXIMUM SAMPLE RATE vs +VCC 1M 390 370 Sample Rate (Hz) Supply Current (µA) fSAMPLE = 12.5kHz 350 330 310 290 100k 10k 270 1k 250 2.0 2.5 3.5 3.0 4.0 4.5 2.0 5.0 2.5 3.0 4.0 4.5 5.0 CHANGE IN OFFSET vs TEMPERATURE CHANGE IN GAIN vs TEMPERATURE 0.15 0.6 0.10 0.4 Delta from +25°C (LSB) Delta from +25°C (LSB) 3.5 +VCC (V) +VCC (V) 0.05 0 –0.05 0.2 0 –0.2 –0.4 –0.10 –0.6 –0.15 –40 –20 0 20 40 60 80 100 –20 0 20 40 60 80 100 Temperature (°C) Temperature (°C) ADS7846 SBAS125H –40 www.ti.com 5 TYPICAL CHARACTERISTICS (Cont.) At TA = +25°C, +VCC = +2.7V, VREF = External +2.5V, fSAMPLE = 125kHz, and fCLK = 16 • fSAMPLE = 2MHz, unless otherwise noted. REFERENCE CURRENT vs TEMPERATURE 18 12 16 Reference Current (µA) Reference Current (µA) REFERENCE CURRENT vs SAMPLE RATE 14 10 8 6 4 14 12 10 8 2 6 0 0 25 50 75 100 –40 125 –20 0 20 40 60 80 Sample Rate (kHz) Temperature (°C) SWITCH-ON RESISTANCE vs +VCC (X+, Y+: +VCC to Pin; X–, Y–: Pin to GND) SWITCH-ON RESISTANCE vs TEMPERATURE (X+, Y+: +VCC to Pin; X–, Y–: Pin to GND) 8 8 7 7 6 6 X– 100 Y– RON (Ω) RON (Ω) Y– 5 X– 4 Y+ X+ 5 X+ 3 3 2 2 1 1 2.0 2.5 3.0 3.5 4.0 4.5 –40 5.0 0 20 40 60 80 100 INTERNAL VREF vs TEMPERATURE MAXIMUM SAMPLING RATE vs RIN 2.0 2.4920 1.8 INL: R = 2k INL: R = 500 DNL: R = 2k DNL: R = 500 1.4 2.4915 2.4910 Internal VREF (V) 1.6 1.2 1.0 0.8 0.6 2.4905 2.4900 2.4895 2.4890 0.4 2.4885 0.2 2.4880 0 2.4875 20 40 60 80 100 120 140 Sampling Rate (kHz) 160 180 –40 –35 –30 –25 –20 –15 –10 –05 0 05 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 Error (LSB) –20 Temperature (°C) +VCC (V) 6 Y+ 4 200 Temperature (°C) ADS7846 www.ti.com SBAS125H TYPICAL CHARACTERISTICS (Cont.) At TA = +25°C, +VCC = +2.7V, VREF = External +2.5V, fSAMPLE = 125kHz, and fCLK = 16 • fSAMPLE = 2MHz, unless otherwise noted. INTERNAL VREF vs TURN-ON TIME 2.4860 80 Internal VREF (%) 100 2.4855 2.4850 3.6 3.5 3.4 3.3 3.2 3.1 3.0 2.9 2.8 0 2.7 2.4840 0 200 400 600 800 1000 1200 Turn-On Time (µS) VCC (V) TEMP DIODE VOLTAGE vs TEMPERATURE (2.7V SUPPLY) TEMP0 DIODE VOLTAGE vs VSUPPLY (25°C) 620 850 750 TEMP0 Diode Voltage (mV) 800 TEMP Diode Voltage (mV) 1µF Cap (1110µS) 12-Bit Settling 40 20 2.6 No Cap (52µS) 12-Bit Settling 60 2.4845 2.5 VREF (V) INTERNAL VREF vs VCC 2.4865 TEMP1 102.7mV 700 650 132.25mV 600 TEMP0 550 618 616 614 612 500 610 450 3.0 –40 –35 –30 –25 –20 –15 –10 –05 0 05 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 2.7 3.3 VSUPPLY (V) Temperature (°C) TEMP1 DIODE VOLTAGE vs VSUPPLY (25°C) TEMP1 Diode Voltage (mV) 732 730 728 726 724 722 2.7 3.0 3.3 VSUPPLY (V) ADS7846 SBAS125H www.ti.com 7 THEORY OF OPERATION possible to negate the error from each touch panel driver switch’s on-resistance (if this is a source of error for the particular measurement). The ADS7846 is a classic successive approximation register (SAR) analog-to-digital converter (ADC). The architecture is based on capacitive redistribution which inherently includes a sample-and-hold function. The converter is fabricated on a 0.6µm CMOS process. ANALOG INPUT See Figure 2 for a block diagram of the input multiplexer on the ADS7846, the differential input of the ADC, and the differential reference of the converter. Table I and Table II show the relationship between the A2, A1, A0, and SER/DFR control bits and the configuration of the ADS7846. The control bits are provided serially via the DIN pin—see the Digital Interface section of this data sheet for more details. The basic operation of the ADS7846 is shown in Figure 1. The device features an internal 2.5V reference and an external clock. Operation is maintained from a single supply of 2.7V to 5.25V. The internal reference can be overdriven with an external, low impedance source between 1V and +VCC. The value of the reference voltage directly sets the input range of the converter. When the converter enters the hold mode, the voltage difference between the +IN and –IN inputs (see Figure 2) is captured on the internal capacitor array. The input current into the analog inputs depends on the conversion rate of the device. During the sample period, the source must charge the internal sampling capacitor (typically 25pF). After the capacitor has been fully charged, there is no further input current. The rate of charge transfer from the analog source to the converter is a function of conversion rate. The analog input (X-, Y-, and Z-position coordinates, auxiliary input, battery voltage, and chip temperature) to the converter is provided via a multiplexer. A unique configuration of low on-resistance touch panel driver switches allows an unselected ADC input channel to provide power and its accompanying pin to provide ground for an external device, such as a touch screen. By maintaining a differential input to the converter and a differential reference architecture, it is +2.7V to +5V 1µF + to 10µF (Optional) ADS7846 0.1µF Touch Screen To Battery Auxiliary Input Serial/Conversion Clock 1 +VCC DCLK 16 2 X+ CS 15 3 Y+ DIN 14 4 X– BUSY 13 Converter Status 5 Y– DOUT 12 Serial Data Out 6 GND PENIRQ 11 7 VBAT +VCC 10 8 AUX VREF Chip Select Serial Data In Pen Interrupt 50kΩ 9 Voltage Regulator FIGURE 1. Basic Operation of the ADS7846. A2 A1 A0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 VBAT AUXIN TEMP Y– X+ Y+ Y-POSITION X-POSITION Z1-POSITION Z2-POSITION +IN (TEMP0) +IN Measure +IN +IN Measure +IN Measure +IN Measure +IN +IN (TEMP1) X-DRIVERS Y-DRIVERS Off Off Off X–, On X–, On On Off Off Off On Off Y+, On Y+, On Off Off Off TABLE I. Input Configuration (DIN), Single-Ended Reference Mode (SER/DFR high). A2 A1 A0 +REF –REF 0 0 1 1 0 1 0 0 1 1 0 1 Y+ Y+ Y+ X+ Y– X– X– X– Y– X+ Y+ +IN +IN Y-POSITION X-POSITION Z1-POSITION Z2-POSITION Measure Measure +IN Measure +IN Measure DRIVERS ON Y+, Y+, Y+, X+, Y– X– X– X– TABLE II. Input Configuration (DIN), Differential Reference Mode (SER/DFR low). 8 ADS7846 www.ti.com SBAS125H +VCC PENIRQ TEMP1 VREF TEMP0 A2-A0 (Shown 001B) SER/DFR (Shown High) X+ X– Ref On/Off Y+ +IN Y– +REF Converter 2.5V Reference –IN –REF 7.5kΩ VBAT 2.5kΩ AUX Battery On GND FIGURE 2. Simplified Diagram of Analog Input. INTERNAL REFERENCE Reference Power Down The ADS7846 has an internal 2.5V voltage reference that can be turned on or off with the control bit, PD1 = 1 (see Table V and Figure 3). Typically, the internal reference voltage is only used in the single-ended mode for battery monitoring, temperature measurement, and for using the auxiliary input. Optimal touch screen performance is achieved when using the differential mode. The internal reference voltage of the ADS7846 must be commanded to be off to maintain compatibility with the ADS7843. Therefore, after power-up, a write of PD1 = 0 is required to insure the reference is off (see the Typical Characteristics for power-up time of the reference from power-down). Band Gap VREF Buffer To CDAC Optional FIGURE 3. Simplified Diagram of the Internal Reference. REFERENCE INPUT The voltage difference between +REF and –REF (shown in Figure 2) sets the analog input range. The ADS7846 operates with a reference in the range of 1V to +VCC. There are several critical items concerning the reference input and its wide voltage range. As the reference voltage is reduced, the analog voltage weight of each digital output code is also reduced. This is often referred to as the LSB (least significant bit) size and is equal to the reference voltage divided by 4096 in 12-bit mode. Any offset or gain error inherent in the ADC appears to increase, in terms of LSB size, as the reference voltage is reduced. For example, if the offset of a given converter is 2LSBs with a 2.5V reference, it is typically 5LSBs with a 1V reference. In each case, the actual offset of the device is the same, 1.22mV. With a lower reference ADS7846 SBAS125H www.ti.com 9 voltage, more care must be taken to provide a clean layout including adequate bypassing, a clean (low-noise, low-ripple) power supply, a low-noise reference (if an external reference is used), and a low-noise input signal. +VCC The voltage into the VREF input directly drives the capacitor digital-to-analog converter (CDAC) portion of the ADS7846. Therefore, the input current is very low (typically < 13µA). There is also a critical item regarding the reference when making measurements where the switch drivers are on. For this discussion, it is useful to consider the basic operation of the ADS7846 (see Figure 1). This particular application shows the device being used to digitize a resistive touch screen. A measurement of the current Y position of the pointing device is made by connecting the X+ input to the ADC, turning on the Y+ and Y– drivers, and digitizing the voltage on X+ (Figure 4 shows a block diagram). For this measurement, the resistance in the X+ lead does not affect the conversion (it does affect the settling time, but the resistance is usually small enough that this is not a concern). However, since the resistance between Y+ and Y– is fairly low, the on-resistance of the Y drivers does make a small difference. Under the situation outlined so far, it is not possible to achieve a 0V input or a full-scale input regardless of where the pointing device is on the touch screen, because some voltage is lost across the internal switches. In addition, the internal switch resistance is unlikely to track the resistance of the touch screen, providing an additional source of error. +VCC VREF Y+ X+ +IN +REF Converter –IN –REF Y– GND FIGURE 5. Simplified Diagram of Differential Reference (SER/DFR Low, Y Switches Enabled, X+ is Analog Input). As a final note about the differential reference mode, it must be used with +VCC as the source of the +REF voltage and cannot be used with VREF. It is possible to use a high precision reference on VREF and single-ended reference mode for measurements which do not need to be ratiometric. In some cases, it is possible to power the converter directly from a precision reference. Most references can provide enough power for the ADS7846, but might not be able to supply enough current for the external load (such as a resistive touch screen). TOUCH SCREEN SETTLING Y+ X+ +IN +REF Converter –IN –REF Y– GND FIGURE 4. Simplified Diagram of Single-Ended Reference (SER/DFR High, Y Switches Enabled, X+ is Analog Input). This situation can be remedied as shown in Figure 5. By setting the SER/DFR bit low, the +REF and –REF inputs are connected directly to Y+ and Y–, respectively, which makes the analog-to-digital conversion ratiometric. The result of the conversion is always a percentage of the external resistance, regardless of how it changes in relation to the on-resistance of the internal switches. Note that there is an important consideration regarding power dissipation when using the ratiometric mode of operation (see the Power Dissipation section for more details). 10 In some applications, external capacitors may be required across the touch screen for filtering noise picked up by the touch screen (for example, noise generated by the LCD panel or backlight circuitry). These capacitors provide a low-pass filter to reduce the noise, but cause a settling time requirement when the panel is touched that typically shows up as a gain error. The problem is that the input and/or reference has not settled to the final steady-state value prior to the ADC sampling the input(s) and providing the digital output. Additionally, the reference voltage may still be changing during the measurement cycle. There are several methods for minimizing or eliminating this issue. Option 1 is to stop or slow down the ADS7846 DCLK for the required touch screen settling time. This allows the input and reference to have stable values for the Acquire period (3 clock cycles of the ADS7846; see Figure 9). This works for both the single-ended and the differential modes. Option 2 is to operate the ADS7846 in the differential mode only for the touch screen measurements and command the ADS7846 to remain on (touch screen drivers on) and not go into power-down (PD0 = 1). Several conversions are made depending on the settling time required and the ADS7846 data rate. Once the required number of conversions have been made, the processor commands the ADS7846 to go into the power-down state on the last measurement. This process is ADS7846 www.ti.com SBAS125H required for X-position, Y-position, and Z-position measurements. Option 3 is to operate in the 15 Clock-per-Conversion mode which overlaps the analog-to-digital conversions and maintains the touch screen drivers on until commanded to stop by the processor (see Figure 12). TEMPERATURE MEASUREMENT In some applications, such as battery recharging, a measurement of ambient temperature is required. The temperature measurement technique used in the ADS7846 relies on the characteristics of a semiconductor junction operating at a fixed current level. The forward diode voltage (VBE) has a well-defined characteristic versus temperature. The ambient temperature can be predicted in applications by knowing the 25°C value of the VBE voltage and then monitoring the delta of that voltage as the temperature changes. The ADS7846 offers two modes of operation. The first mode requires calibration at a known temperature, but only requires a single reading to predict the ambient temperature. The PENIRQ diode is used (turned on) during this measurement cycle. The voltage across the diode is connected through the MUX for digitizing the forward bias voltage by the ADC with an address of A2 = 0, A1 = 0, and A0 = 0 (see Table I and Figure 6 for details). This voltage is typically 600mV at +25°C with a 20µA current through the diode. The absolute value of this diode voltage can vary a few millivolts. However, the TC of this voltage is very consistent at –2.1mV/°C. During the final test of the end product, the diode voltage would be stored at a known room temperature, in memory, for calibration purposes by the user. The result is an equivalent temperature measurement resolution of 0.3°C/LSB (in 12-bit mode). represented by kT/q • ln (N), where N is the current ratio = 91, k = Boltzmann’s constant (1.38054 • 10–23 electron volts/degrees Kelvin), q = the electron charge (1.602189 • 10–19 C), and T = the temperature in degrees Kelvin. This method can provide improved absolute temperature measurement over the first mode at the cost of less resolution (1.6°C/LSB). The equation for solving for °K is: °K = q • ∆V/(k • ln (N)) where, (1) ∆V = V (I91) – V (I1) (in mV) ∴ °K = 2.573°K/mV • ∆V °C = 2.573 • ∆V(mV) – 273°K NOTE: The bias current for each diode temperature measurement is only on for 3 clock cycles (during the acquisition mode). Therefore, it does not add any noticeable increase in power, especially if the temperature measurement only occurs occasionally. BATTERY MEASUREMENT An added feature of the ADS7846 is the ability to monitor the battery voltage on the other side of the voltage regulator (DC/DC converter), as shown in Figure 7. The battery voltage can vary from 0.5V to 6V, while maintaining the voltage to the ADS7846 at 2.7V, 3.3V, etc. The input voltage (VBAT) is divided down by 4 so that a 6.0V battery voltage is represented as 1.5V to the ADC. This simplifies the multiplexer and control logic. In order to minimize the power consumption, the divider is only on during the sampling period when A2 = 0, A1 = 1, and A0 = 0 (see Table I for the relationship between the control bits and configuration of the ADS7846). +VCC External Pull-Up PENIRQ 2.7V DC/DC Converter X+ MUX Battery 0.5V + to 6.0V ADC +VCC Temperature Select TEMP0 0.125V to 1.5V VBAT TEMP1 7.5kΩ FIGURE 6. Functional Block Diagram of Temperature Measurement Mode. The second mode does not require a test temperature calibration, but uses a two-measurement method to eliminate the need for absolute temperature calibration and for achieving 2°C accuracy. This mode requires a second conversion with an address of A2 = 1, A1 = 1, and A0 = 1, with a 91 times larger current. The voltage difference between the first and second conversion using 91 times the bias current is 2.5kΩ FIGURE 7. Battery Measurement Functional Block Diagram. ADS7846 SBAS125H www.ti.com 11 PRESSURE MEASUREMENT Measure X-Position Measuring touch pressure can also be done with the ADS7846. To determine pen or finger touch, the pressure of the touch needs to be determined. Generally, it is not necessary to have very high performance for this test; therefore, the 8-bit resolution mode is recommended (however, calculations will be shown here are in 12-bit resolution mode). There are several different ways of performing this measurement. The ADS7846 supports two methods. The first method requires knowing the X-plate resistance, measurement of the X-Position, and two additional cross-panel measurements (Z1 and Z2) of the touch screen, as shown in Figure 8. Using Equation 2 calculates the touch resistance: RTOUCH = RX – plate • X – Position Z2 – 1 4096 Z1 X+ Touch X-Position Y– X– Measure Z1-Position Y+ X+ Touch Z1-Position (2) X– The second method requires knowing both the X-plate and Y-plate resistance, measurement of X-Position and Y-Position, and Z1. Using Equation 3 also calculates the touch resistance: R TOUCH = Y+ Y– Y+ X+ Touch R X − plate • X − Position 4096 Z – 1 4096 1 Z2-Position (3) Y Position – R Y − plate • 1– 4096 X– Y– Measure Z2-Position DIGITAL INTERFACE FIGURE 8. Pressure Measurement Block Diagrams. Figure 9 shows the typical operation of the ADS7846 digital interface. This diagram assumes that the source of the digital signals is a microcontroller or digital signal processor with a basic serial interface. Each communication between the processor and the converter, such as SPI/SSI or Microwire™ synchronous serial interface, consists of eight clock cycles. One complete conversion can be accomplished with three serial communications for a total of 24 clock cycles on the DCLK input. The first eight clock cycles are used to provide the control byte via the DIN pin. When the converter has enough information about the following conversion to set the input multiplexer and reference inputs appropriately, the converter enters the acquisition (sample) mode and, if needed, the touch panel drivers are turned on. After three more clock cycles, the control byte is complete and the converter enters the conversion mode. At this point, the input CS tACQ DCLK DIN 1 S 8 A2 A1 8 1 1 8 SER/ A0 MODE DFR PD1 PD0 (START) Idle Acquire Conversion Idle BUSY DOUT 11 10 9 8 7 6 5 4 3 (MSB) DRIVERS 1 AND 2(1) (SER/DFR High) DRIVERS 1 AND 2(1, 2) (SER/DFR Low) Off 2 1 0 Zero Filled... (LSB) On Off Off On Off NOTES: (1) For Y-Position, Driver 1 is on, X+ is selected, and Driver 2 is off. For X-Position, Driver 1 is off, Y+ is selected, and Driver 2 is on. Y– will turn on when power-down mode is entered and PD0 = 0B. (2) Drivers will remain on if PD0 = 1 (no power down) until selected input channel, reference mode, or power-down mode is changed, or CS is HIGH. FIGURE 9. Conversion Timing, 24 Clocks-per-Conversion, 8-bit Bus Interface. No DCLK delay required with dedicated serial port. 12 ADS7846 www.ti.com SBAS125H sample-and-hold goes into the hold mode and the touch panel drivers turn off (in single-ended mode). The next 12 clock cycles accomplish the actual analog-to-digital conversion. If the conversion is ratiometric (SER/DFR = 0), the drivers are on during the conversion and a 13th clock cycle is needed for the last bit of the conversion result. Three more clock cycles are needed to complete the last byte (DOUT will be low), which are ignored by the converter. Control Byte The control byte (on DIN), as shown in Table III, provides the start conversion, addressing, ADC resolution, configuration, and power-down of the ADS7846. Figure 9 and Tables III and IV give detailed information regarding the order and description of these control bits within the control byte. Bit 7 (MSB) Bit 6 Bit 5 Bit 4 S A2 A1 A0 Bit 3 Bit 2 MODE SER/DFR Bit 1 Bit 0 (LSB) PD1 PD0 TABLE III. Order of the Control Bits in the Control Byte. BIT NAME 7 S DESCRIPTION Start Bit. Control byte starts with first high bit on DIN. A new control byte can start every 15th clock cycle in 12-bit conversion mode or every 11th clock cycle in 8-bit conversion mode (see Figure 12). 6-4 A2-A0 Channel Select Bits. Along with the SER/DFR bit, these bits control the setting of the multiplexer input, touch driver switches, and reference inputs (see Tables I and II). 3 MODE 12-Bit/8-Bit Conversion Select Bit. This bit controls the number of bits for the next conversion: 12-bits (low) or 8-bits (high). 2 SER/DFR Single-Ended/Differential Reference Select Bit. Along with bits A2-A0, this bit controls the setting of the multiplexer input, touch driver switches, and reference inputs (see Tables I and I). 1-0 PD1-PD0 Power-Down Mode Select Bits. See Table V for details. TABLE IV. Descriptions of the Control Bits within the Control Byte. SER/DFR—The SER/DFR bit controls the reference mode, either single-ended (high) or differential (low). The differential mode is also referred to as the ratiometric conversion mode and is preferred for X-Position, Y-Position, and PressureTouch measurements for optimum performance. The reference is derived from the voltage at the switch drivers, which is almost the same as the voltage to the touch screen. In this case a reference voltage is not needed, as the reference voltage to the ADC is the voltage across the touch screen. In the single-ended mode, the converter reference voltage is always the difference between the VREF and GND pins (see Tables I and II, and Figures 2 through 5 for further information). If X-Position, Y-Position, and Pressure-Touch are measured in the single-ended mode, an external reference voltage is needed. The ADS7846 should also be powered from the external reference. Caution must be observed when using the single-ended mode such that the input voltage to the ADC does not exceed the internal reference voltage, especially if the supply voltage is greater than 2.7V. NOTE: The differential mode can only be used for X-Position, Y-Position, and Pressure-Touch measurements. All other measurements require the single-ended mode. PD0 and PD1—Table V describes the power-down and the internal reference voltage configurations. The internal reference voltage can be turned on or off independently of the ADC. This can allow extra time for the internal reference voltage to settle to the final value prior to making a conversion. Make sure to also allow this extra wake-up time if the internal reference is powered down. The ADC requires no wake-up time and can be instantaneously used. Also note that the status of the internal reference power-down is latched into the part (internally) with BUSY going high. Therefore, in order to turn the reference off, an additional write to the ADS7846 is required after the channel is converted. PD1 PD0 PENIRQ DESCRIPTION 0 0 Enabled Power-Down Between Conversions. When each conversion is finished, the converter enters a low-power mode. At the start of the next conversion, the device instantly powers up to full power. There is no need for additional delays to assure full operation and the very first conversion is valid. The Y– switch is on when in power-down. 0 1 Disabled Reference is off and ADC is on. 1 0 Enabled Reference is on and ADC is off. 1 1 Disabled Device is always powered. Reference is on and ADC is on. Initiate START—The first bit, the S bit, must always be high and initiates the start of the control byte. The ADS7846 ignores inputs on the DIN pin until the start bit is detected. Addressing—The next three bits (A2, A1, and A0) select the active input channel(s) of the input multiplexer (see Tables I, II, and Figure 2), touch screen drivers, and the reference inputs. MODE—The mode bit sets the resolution of the ADC. With this bit low, the next conversion has 12 bits of resolution; with this bit high, the next conversion has 8 bits of resolution. TABLE V. Power-Down and Internal Reference Selection. ADS7846 SBAS125H www.ti.com 13 16 Clocks-per-Conversion SYMBOL DESCRIPTION MIN The control bits for conversion n + 1 can be overlapped with conversion n to allow for a conversion every 16 clock cycles, as shown in Figure 10. This figure also shows possible serial communication occurring with other serial peripherals between each byte transfer from the processor to the converter. This is possible provided that each conversion completes within 1.6ms of starting. Otherwise, the signal that is captured on the input sample-and-hold may droop enough to affect the conversion result. Note that the ADS7846 is fully powered while other serial communications are taking place during a conversion. tACQ Acquisition Time 1.5 tDS DIN Valid Prior to DCLK Rising 100 ns tDH DIN Hold After DCLK High 10 ns Digital Timing Figures 9, 11, and Table VI provide detailed timing for the digital interface of the ADS7846. TYP MAX UNITS µs tDO DCLK Falling to DOUT Valid 200 ns tDV CS Falling to DOUT Enabled 200 ns 200 ns tTR CS Rising to DOUT Disabled tCSS CS Falling to First DCLK Rising 100 tCSH CS Rising to DCLK Ignored 0 ns tCH DCLK High 200 ns tCL DCLK Low 200 tBD DCLK Falling to BUSY Rising 200 ns tBDV CS Falling to BUSY Enabled 200 ns tBTR CS Rising to BUSY Disabled 200 ns ns ns TABLE VI. Timing Specifications (+VCC = +2.7V and Above, TA = –40°C to +85°C, CLOAD = 50pF). CS DCLK 1 DIN 8 1 8 1 S 8 1 S Control Bits Control Bits BUSY DOUT 11 10 9 8 7 6 5 4 3 2 1 0 11 10 9 FIGURE 10. Conversion Timing, 16 Clocks-per-Conversion, 8-Bit Bus Interface. No DCLK delay required with dedicated serial port. CS tCSS tCL tCH tBD tBD tD0 tCSH DCLK tDS tDH PD0 DIN tBDV tBTR BUSY tDV tTR DOUT 11 10 FIGURE 11. Detailed Timing Diagram. 14 ADS7846 www.ti.com SBAS125H 15 Clocks-per-Conversion 8-Bit Conversion Figure 12 provides the fastest way to clock the ADS7846. This method does not work with the serial interface of most microcontrollers and digital signal processors, as they are generally not capable of providing 15 clock cycles per serial transfer. However, this method can be used with field programmable gate arrays (FPGAs) or application specific integrated circuits (ASICs). Note that this effectively increases the maximum conversion rate of the converter beyond the values given in the specification tables, which assume 16 clock cycles per conversion. The ADS7846 provides an 8-bit conversion mode that can be used when faster throughput is needed and the digital result is not as critical. By switching to the 8-bit mode, a conversion is complete four clock cycles earlier. Not only does this shorten each conversion by four bits (25% faster throughput), but each conversion can actually occur at a faster clock rate. This is because the internal settling time of the ADS7846 is not as critical—settling to better than 8 bits is all that is needed. The clock rate can be as much as 50% faster. The faster clock rate and fewer clock cycles combine to provide a 2x increase in conversion rate. Data Format The ADS7846 output data is in Straight Binary format as shown in Figure 13. This figure shows the ideal output code for the given input voltage and does not include the effects of offset, gain, or noise. POWER DISSIPATION There are two major power modes for the ADS7846: full power (PD0 = 1B) and auto power-down (PD0 = 0B). When operating at full speed and 16 clocks-per-conversion (see Figure 10), the ADS7846 spends most of the time acquiring or converting. There is little time for auto power-down, assuming that this mode is active. Therefore, the difference between full-power mode and auto power-down is negligible. If the conversion rate is decreased by slowing the frequency of the DCLK input, the two modes remain approximately equal. However, if the DCLK frequency is kept at the maximum rate during a conversion but conversions are done less often, the difference between the two modes is dramatic. FS = Full-Scale Voltage = VREF(1) 1LSB = VREF(1)/4096 1LSB 11...111 Output Code 11...110 11...101 00...010 00...001 00...000 FS – 1LSB 0V Input Voltage(2) (V) NOTES: (1) Reference voltage at converter: +REF – (–REF), see Figure 2. (2) Input voltage at converter, after multiplexer: +IN – (–IN), see Figure 2. FIGURE 13. Ideal Input Voltages and Output Codes. CS Power Down DCLK 15 1 DIN S SGL/ A2 A1 A0 MODE DIF PD1 PD0 1 S 15 SGL/ A2 A1 A0 MODE DIF PD1 PD0 1 S A2 A1 A0 BUSY DOUT 11 10 9 8 7 6 5 4 3 2 1 0 11 10 9 8 7 Tri-State FIGURE 12. Maximum Conversion Rate, 15 Clocks-per-Conversion. ADS7846 SBAS125H www.ti.com 15 Figure 14 shows the difference between reducing the DCLK frequency (scaling DCLK to match the conversion rate) or maintaining DCLK at the highest frequency and reducing the number of conversions per second. In the latter case, the converter spends an increasing percentage of time in powerdown mode (assuming the auto power-down mode is active). 1000 Supply Current (µA) fCLK = 16 • fSAMPLE 100 fCLK = 2MHz 10 TA = 25°C +VCC = +2.7V 1 1k 10k 100k 1M fSAMPLE (Hz) FIGURE 14. Supply Current versus Directly Scaling the Frequency of DCLK with Sample Rate or Maintaining DCLK at the Maximum Possible Frequency. Another important consideration for power dissipation is the reference mode of the converter. In the single-ended reference mode, the touch panel drivers are on only when the analog input voltage is being acquired (see Figure 9 and Table I). Therefore, the external device (e.g., a resistive touch screen) is only powered during the acquisition period. In the differential reference mode, the external device must be powered throughout the acquisition and conversion periods (see Figure 9). If the conversion rate is high, this could substantially increase power dissipation. CS also puts the ADS7846 into power-down mode. When CS goes high, the ADS7846 immediately goes into powerdown and does not complete the current conversion. However, the internal reference does not turn off with CS going high. To turn the reference off, an additional write is required before CS goes high (PD1 = 0). 16 LAYOUT The following layout suggestions provide the most optimum performance from the ADS7846. However, many portable applications have conflicting requirements concerning power, cost, size, and weight. In general, most portable devices have fairly clean power and grounds because most of the internal components are very low power. This situation means less bypassing for the converter power and less concern regarding grounding. Still, each situation is unique and the following suggestions should be reviewed carefully. For optimum performance, care must be taken with the physical layout of the ADS7846 circuitry. The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections, and digital inputs that occur just prior to latching the output of the analog comparator. Therefore, during any single conversion for an n-bit SAR converter, there are n ‘windows’ in which large external transient voltages can easily affect the conversion result. Such glitches can originate from switching power supplies, nearby digital logic, and high-power devices. The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the external event. The error can change if the external event changes in time with respect to the DCLK input. With this in mind, power to the ADS7846 should be clean and well bypassed. A 0.1µF ceramic bypass capacitor should be placed as close to the device as possible. A 1µF to 10µF capacitor may also be needed if the impedance of the connection between +VCC and the power supply is high. Lowleakage capacitors should be used to minimize power dissipation through the bypass capacitors when the ADS7846 is in power-down mode. A bypass capacitor is generally not needed on the VREF pin because the internal reference is buffered by an internal op amp. If an external reference voltage originates from an op amp, make sure that it can drive any bypass capacitor that is used without oscillation. The ADS7846 architecture offers no inherent rejection of noise or voltage variation in regards to using an external reference input. This is of particular concern when the reference input is tied to the power supply. Any noise and ripple from the supply appears directly in the digital results. Whereas high-frequency noise can be filtered out, voltage variation due to line frequency (50Hz or 60Hz) can be difficult to remove. ADS7846 www.ti.com SBAS125H The GND pin must be connected to a clean ground point. In many cases, this is the analog ground. Avoid connections which are too near the grounding point of a microcontroller or digital signal processor. If needed, run a ground trace directly from the converter to the power-supply entry or batteryconnection point. The ideal layout includes an analog ground plane dedicated to the converter and associated analog circuitry. +VCC 100kΩ Y+ In the specific case of use with a resistive touch screen, care should be taken with the connection between the converter and the touch screen. Although resistive touch screens have fairly low resistance, the interconnection should be as short and robust as possible. Longer connections are a source of error, much like the on-resistance of the internal switches. Likewise, loose connections can be a source of error when the contact resistance changes with flexing or vibrations. As indicated previously, noise can be a major source of error in touch screen applications (for example, applications that require a backlit LCD panel). This EMI noise can be coupled through the LCD panel to the touch screen and cause “flickering” of the converted data. Several things can be done to reduce this error, such as using a touch screen with a bottom-side metal layer connected to ground to shunt the majority of noise to ground. Additionally, filtering capacitors, from Y+, Y–, X+, and X– pins to ground can also help. Caution should be observed under these circumstances for settling time of the touch screen, especially operating in the single-ended mode and at high data rates. PENIRQ OUTPUT The pen-interrupt output function is shown in Figure 15. While in power-down mode with PD0 = 0, the Y– driver is on and connects the Y-plane of the touch screen to GND. The PENIRQ output is connected to the X+ input through two transmission gates. When the screen is touched, the X+ input is pulled to ground through the touch screen. The PENIRQ output goes low due to the current path through the touch screen to ground, which initiates an interrupt to the processor. During the measurement cycle for X-, Y-, and Z-Position, the X+ input is disconnected from the external pull-up resistor. This is done to eliminate any leakage current from the external pull-up resistor through the touch screen, thus causing no errors. X+ Y– On Y or X drivers on, or TEMP0, TEMP1 measurements activated. FIGURE 15. ADS7846 PENIRQ Functional Block Diagram. Furthermore, the PENIRQ output is disabled and low during the measurement cycle for X-, Y-, and Z-Position. The PENIRQ output is disabled and high during the measurement cycle for battery monitor, auxiliary input, and chip temperature. If the last control byte written to the ADS7846 contains PD0 = 1, the peninterrupt output function is disabled and is not able to detect when the screen is touched. In order to re-enable the peninterrupt output function under these circumstances, a control byte needs to be written to the ADS7846 with PD0 = 0. If the last control byte written to the ADS7846 contains PD0 = 0, the pen-interrupt output function is enabled at the end of the conversion. The end of the conversion occurs on the falling edge of DCLK after bit 1 of the converted data is clocked out of the ADS7846. It is recommended that the processor mask the interrupt PENIRQ is associated with whenever the processor sends a control byte to the ADS7846. This prevents false triggering of interrupts when the PENIRQ output is disabled, as in the cases discussed in this section. ADS7846 SBAS125H PENIRQ www.ti.com 17 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) ADS7846E ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846E/2K5 ACTIVE SSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846E/2K5G4 ACTIVE SSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846EG4 ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846IGQCR ACTIVE BGA MICROSTAR JUNIOR GQC 48 ADS7846IRGVR ACTIVE VQFN RGV 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846IRGVRG4 ACTIVE VQFN RGV 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846IRGVT ACTIVE VQFN RGV 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846IRGVTG4 ACTIVE VQFN RGV 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846N ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846N/2K5 ACTIVE TSSOP PW 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846N/2K5G4 ACTIVE TSSOP PW 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS7846NG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TBD (1) Call TI Call TI The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant ADS7846E/2K5 SSOP DBQ 16 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 ADS7846IRGVR VQFN RGV 16 2500 330.0 12.4 4.3 4.3 1.5 8.0 12.0 Q2 ADS7846IRGVT VQFN RGV 16 250 330.0 12.4 4.3 4.3 1.5 8.0 12.0 Q2 ADS7846N/2K5 TSSOP PW 16 2500 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADS7846E/2K5 SSOP DBQ 16 2500 367.0 367.0 35.0 ADS7846IRGVR VQFN RGV 16 2500 338.1 338.1 20.6 ADS7846IRGVT VQFN RGV 16 250 338.1 338.1 20.6 ADS7846N/2K5 TSSOP PW 16 2500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA MPLG008D – APRIL 2000 – REVISED FEBRUARY 2002 GQC (S-PBGA-N48) PLASTIC BALL GRID ARRAY 4,10 3,90 SQ 3,00 TYP 0,50 G F 0,50 E D 3,00 TYP C B A 1 A1 Corner 2 3 4 5 6 7 Bottom View 0,77 0,71 1,00 MAX Seating Plane 0,35 0,25 0,25 0,05 M 0,08 0,15 4200460/E 01/02 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. MicroStar Junior BGA configuration Falls within JEDEC MO-225 MicroStar Junior is a trademark of Texas Instruments. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated