LH1262CAC, LH1262CACTR, LH1262CB www.vishay.com Vishay Semiconductors Dual Photovoltaic MOSFET Driver Solid-State Relay FEATURES DIP 8 7 6 5 • High open circuit voltage • High short circuit current • Isolation test voltage 5300 VRMS • Logic compatible input • High reliability 1 SMD 2 3 • Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC 4 + Control 1 - Control 1 - Control 1 + Control 1 + Control 2 - Control 2 - Control 2 + Control 2 APPLICATIONS • High-side driver • Solid state relays • Floating power supply i179020_6 • Power control DESCRIPTION • Data acquisition The LH1262CB, LH1262CAC photovoltaic MOSFET driver consists of two LEDs optically coupled to two photodiode arrays. The photodiode array provides a floating source with adequate voltage and current to drive high-power MOSFET transistors. Optical coupling provides a high I/O isolation voltage. In order to turn the MOSFET off, an external resistance (gate-to-source) is required for gate discharge. • ATE • Isolated switching Note • See “Solid-State Relays” (application note 56) AGENCY APPROVALS UL1577: pending BSI/BABT: pending DIN EN: pending FIMKO: pending ORDERING INFORMATION L H 1 2 PART NUMBER PACKAGE SMD-8 SMD-8, tape and reel DIP-8 Rev. 1.4, 26-Sep-11 6 2 # ELECTR. VARIATION # # PACKAGE CONFIG. T DIP R TAPE AND REEL 7.62 mm SMD > 0.1 mm UL, BSI, VDE, FIMKO LH1262CAC LH1262CACTR LH1262CB Document Number: 83802 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1262CAC, LH1262CACTR, LH1262CB www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT LED input ratings reverse voltage IR ≤ 10 μA IF 50 mA VR 5.0 Photodiode array reverse voltage IR ≤ 2.0 μA VR V 100 V SSR LED input ratings continuous forward current Ambient operating temperature range Tamb - 40 to + 85 °C Storage temperature range Tstg - 40 to + 150 °C TS 270 °C Pin soldering time (1) t = 7.0 s max. Input to output isolation voltage t = 60 s min. VISO 5300 VRMS Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT LED forward voltage PARAMETER IF = 10 mA VF 1.15 1.26 1.45 V Detector forward voltage IF = 10 μA VF(PDA) 14 V Detector reverse voltage IR = 2.0 μA VR(PDA) 200 V IF = 5.0 mA VOC IF = 10 mA VOC 13.45 IF = 20 mA VOC 13.92 IF = 5.0 mA ISC 1.0 IF = 10 mA ISC 2.6 IF = 20 mA ISC Open circuit voltage (pins 5, 6 or 7, 8) Short circuit current (pins 5, 6 or 7, 8) 10 12.95 15 V V V 1.6 6.5 3.4 14 6.9 μA μA μA Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL Turn-on time IF = 20 mA (1) ton MIN. TYP. 35 MAX. UNIT μs Turn-off time IF = 20 mA (1) toff 90 μs Note (1) f = 1.0 kHz, pulse width = 100 μs, load (R ) = 1.0 MΩ, 15 pF; measured at 90 % rated voltage (t ), 10 % rated voltage (t ). Actuation speed L on off depends upon the external ton and toff circuitry and the capacitance of the MOSFET. FUNCTIONAL DESCRIPTION Figure 1 outlines the IV characteristics of the illuminated photodiode array (PDA). For operation at voltages below VOC, the PDA acts as a nearly constant current source. The actual region of operation depends upon the load. The amount of current applied to the LED (pins 1 and 2 or 3 and 4) determines the amount of light produced for the PDA. For high temperature operation, more LED current may be required. Rev. 1.4, 26-Sep-11 Document Number: 83802 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1262CAC, LH1262CACTR, LH1262CB www.vishay.com Vishay Semiconductors 8 1 – Channel 1 control Switch 1 N-channel MOSFETs P-channel JFET + 2 7 2.0 MΩ 6 3 – Switch 2 N-channel MOSFETs P-channel JFET Channel 2 control + 4 5 2.0 MΩ ilh1262cb_08 Fig. 1 - Typical Dual Form A Solid-State Relay Application PACKAGE DIMENSIONS in inches (millimeters) DIP pin one ID 4 3 2 1 5 6 7 8 6.81 6.48 ISO method A 9.91 9.63 1.14 0.76 7.62 typ. 0.79 4° typ. 3.81 3.30 1.27 10° 0.89 0.51 0.56 0.46 2.54 typ. 6.35 5.84 3° to 9° 0.30 0.20 3.30 2.79 i178008 Rev. 1.4, 26-Sep-11 Document Number: 83802 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1262CAC, LH1262CACTR, LH1262CB www.vishay.com Vishay Semiconductors SMD pin one ID 0.76 6.81 6.48 R 0.25 2.54 1.78 8 min. 11.05 9.91 9.63 10.03 9.52 0.79 typ. ISO method A 1.14 0.78 3.81 3.30 1.52 radius 7.80 7.52 3° to 7° 4° typ. 1.27 typ. i178009 Rev. 1.4, 26-Sep-11 10° 0.25 0.10 2.54 typ. 8 typ. 0.3 typ. 1.02 0.51 Document Number: 83802 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000