RFM SF2211E

Preliminary
• No Matching Network Required for 50 Ω Operation
• Surface-mount 3.0 x 3.0 mm Package
• Complies with Directive 2002/95/EC (RoHS)
SF2211E
Pb
1200 MHz
SAW Filter
Absolute Maximum Ratings
Value
Units
Input Power Level
Rating
10
dBm
DC Voltage on any Non-ground Terminal
3
V
Operating Temperature Range
-55 to +85
°C
Storage Temperature Range in Tape and Reel
-40 to +85
°C
Component Storage Temperature Range
-55 to +95
°C
260
°C
Solder Reflow Temperature, 10 seconds, 5 cycles maximum
SM3030-6
Electrical Characteristics
Characteristic
Sym
Notes
Min
Typ
Max
Center Frequency
fC
1200
Insertion Loss, 1180 to 1220 MHz
IL
2.8
Units
MHz
4.0
dB
Attenuation, 0 dB Reference:
1080 MHz
35
60
1100 MHz
45
60
1300 MHz
40
48
1320 MHz
35
52
Source Impedance
ZS
50
Load Impedance
ZL
50
Case Style
Ω
SM3030-6 3.0 x 3.0 mm Nominal Footprint
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
dB
945, YWWS
Reel Size 7 Inch
500 Pieces/Reel
Reel Size 13 Inch
3000 Pieces/Reel
Electrical Connections
Connection
Port 1
Terminals
2
Port 2
1
6
5
Case Ground
All others
5 0 o h m
L o a d
5
4
(b o tto m
5 0 o h m
S o u rc e
2
3
v ie w )
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 Ω and measured with 50 Ω network analyzer.
Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
"LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
The design, manufacturing process, and specifications of this filter are subject to change.
Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc., are registered trademarks of RF Monolithics, Inc.
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
Page 1 of 5
SF2211E - 7/16/10
Filter Frequency Response
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
Page 2 of 5
SF2211E - 7/16/10
Filter Input Impedance
Filter Output Impedance
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
Page 3 of 5
SF2211E - 7/16/10
SM3030-6 Case
6-Terminal Ceramic Surface-Mount Case
3.0 X 3.0 mm Nominal Footprint
Case and PCB Footprint Dimensions
Dimension
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
K
L
N
mm
Nom
3.00
3.00
1.25
0.90
2.80
1.60
0.85
1.50
0.60
1.30
3.20
1.70
1.05
0.81
0.38
Min
2.87
2.87
1.12
0.77
2.67
1.47
0.72
1.37
0.47
1.17
Max
3.13
3.13
1.38
1.03
2.93
1.73
0.98
1.63
0.73
1.43
Inches
Nom
0.118
0.118
0.049
0.035
0.110
0.063
0.033
0.059
0.024
0.051
0.126
0.067
0.041
0.032
0.015
Min
0.113
0.113
0.044
0.030
0.105
0.058
0.028
0.054
0.019
0.046
Max
0.123
0.123
0.054
0.040
0.115
0.068
0.038
0.064
0.029
0.056
Case Materials
K
Materials
N
O
N
Solder Pad
Plating
0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel
Lid Plating
2.0 to 3.0 µm Nickel
Body
Al2O3 Ceramic
Pb Free
M
M
PCB Footprint Top View
Top View
Bottom View
B
1
3
6
945
YWWS
A 2
5
E
4
D
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
G
C
F
H
6
1
5
2
4
3
I
J
Page 4 of 5
SF2211E - 7/16/10
Tape and Reel Specifications
Quantity Per Reel
millimeters
7
178
500
13
330
3000
"B" REF.
100 REF.
“B”
Inches
See Detail "A"
13.
0
12.0
20
.2
2.0
COMPONENT ORIENTATION and DIMENSIONS
Carrier Tape Dimensions
Ao
Bo
Ko
Pitch
W
2.0
4.0
PIN #1
A
1.50
1.75
0.3 ± 0.05
3.35 mm
3.35 mm
1.40 mm
8.0 mm
12.0 mm
Bo
B
Ao
12.0
5.5
RO.3
(MAX.)
B
Pitch
A
Ko
R0.5
(MAX.)
1.5
SECTION A-A
SECTION B-B
www.RFM.com E-mail: [email protected]
©2009-2010 by RF Monolithics, Inc.
USER DIRECTION OF FEED
Page 5 of 5
SF2211E - 7/16/10