SF2133E • Low Loss SAW Filter • Surface Mount 3.0 x 3.0 mm Package • Complies with Directive 2002/95/EC (RoHS) Pb 1747.50 MHz SAW Filter Absolute Maximum Ratings Rating Value Units Input Power Level 5 dBm DC Voltage on any Non-ground Terminal 3 V Operating Temperature Range -40 to +85 °C Storage Temperature Range in Tape and Reel -40 to +90 °C 265 °C Maximum Soldering Profile, 5 cycles/10 seconds maximum SM3030-6 Electrical Characteristics Notes Min Max Max -20 to +70 °C -40 to +85 °C 2.6 4.0 4.1 1.6 2.5 2.8 Characteristic Sym Typ Center Frequency fC 1747.5 Insertion Loss, 1710 to 1785 MHz IL Amplitude Ripple, 1710 to 1785 MHz Units MHz dB dBP-P Attenuation Referenced to 0 dB: 10 to 1670 MHz 15 23 1670 to 1690 MHz 6 23.9 1805 to 1880 MHz 6 24 1880 to 4500 MHz 15 25 4500 to 5000 MHz 10 Input/Output VSWR, 1710 to 1785 MHz dB 14 1.8:1 2.5:1 2.5:1 Source Impedance ZS 50 Ω Load Impedance ZL 50 Ω Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity 679, YWWS Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel Electrical Connections Connection Terminals Input 2 Output 5 Case Ground All others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. www.RFM.com E-mail: [email protected] © 2009-2011 by RF Monolithics, Inc. Page 1 of 5 SF2133E - 9/21/11 www.RFM.com E-mail: [email protected] © 2009-2011 by RF Monolithics, Inc. Page 2 of 5 SF2133E - 9/21/11 www.RFM.com E-mail: [email protected] © 2009-2011 by RF Monolithics, Inc. Page 3 of 5 SF2133E - 9/21/11 SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials K Materials N O N Solder Pad Plating 0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel Lid Plating 2.0 to 3.0 µm Nickel Body Al2O3 Ceramic Pb Free M M PCB Footprint Top View Top View Bottom View B 1 3 6 679 YWWS A 2 5 E 4 D www.RFM.com E-mail: [email protected] © 2009-2011 by RF Monolithics, Inc. G C F H 6 1 5 2 4 3 I J Page 4 of 5 SF2133E - 9/21/11 Tape and Reel Specifications "B" REF. 100 REF. “B” Quantity Per Reel Inches millimeters 7 178 500 13 330 3000 See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions 2.0 3.35 mm Bo 3.35 mm Ko 1.40 mm Pitch 8.0 mm W 12.0 mm 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 Ao 679 YWWS Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B www.RFM.com E-mail: [email protected] © 2009-2011 by RF Monolithics, Inc. USER DIRECTION OF FEED Page 5 of 5 SF2133E - 9/21/11