Preliminary SF2195E • Surface Mount 3.0 x 3.0 x 1.3 mm Package • Complies with Directive 2002/95/EC (RoHS) 842.5 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units 15 dBm Input Power Level DC Voltage on any Non-ground Terminal 5 V Operating Temperature Range -30 to +70 °C Storage Temperature Range in Tape and Reel -40 to +85 °C 260 °C Solder Reflow Temperature, 10 seconds, 5 cycles maximum SM3030-6 Electrical Characteristics Characteristic Sym Center Frequency FC Notes Min Typ Units 842.5 1 dB Bandwidth TBD 3 dB Bandwidth TBD IL Insertion Loss, 840 to 845 MHz Max 1.9 MHz 3.5 dB Amplitude Ripple, 840 to 845 MHz 0.3 1.0 dBP-P Group Delay Deviation, 840 to 845 MHz 10 40 nsP-P 1.5:1 2.0:1 VSWR, 840 to 845 MHz Attenuation Referenced to 0 dB DC to 795 MHz 45 52 795 to 800 MHz 40 50 894 to 968 MHz 30 37 1059 to 1078 MHz 50 60 25 30 1078 to 3000 MHz Source Impedance ZS 50 Load Impedance ZL 50 Case Style SM3030-6 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator Standard Reel Quantity dB 919, YWWS Reel Size 7 Inch 500 Pieces/Reel Reel Size 13 Inch 3000 Pieces/Reel Electrical Connections Connection Terminals Input 5 Output 2 Ground All Others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc., are registered trademarks of RF Monolithics, Inc www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 1 of 6 SF2195E - 7/19/10 Filter Passband Response, 740 to 940 MHz Filter Test Circuit 5 0 o h m 5 SF2195E 2 5 0 o h m 1 , 3 , 4 , 6 www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 2 of 6 SF2195E - 7/19/10 Filter Broadband Response, 0 to 3000 MHz www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 3 of 6 SF2195E - 7/19/10 Filter S11 Plot Filter S22 Plot www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. Page 4 of 6 SF2195E - 7/19/10 SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case and PCB Footprint Dimensions Dimension A B C D E F G H I J K L M N O K L N K N mm Nom 3.00 3.00 1.25 0.90 2.80 1.60 0.85 1.50 0.60 1.30 3.20 1.70 1.05 0.81 0.38 Max 3.13 3.13 1.38 1.03 2.93 1.73 0.98 1.63 0.73 1.43 Min 0.113 0.113 0.044 0.030 0.105 0.058 0.028 0.054 0.019 0.046 Inches Nom 0.118 0.118 0.049 0.035 0.110 0.063 0.033 0.059 0.024 0.051 0.126 0.067 0.041 0.032 0.015 Max 0.123 0.123 0.054 0.040 0.115 0.068 0.038 0.064 0.029 0.056 Case Materials O Materials N M M Min 2.87 2.87 1.12 0.77 2.67 1.47 0.72 1.37 0.47 1.17 PCB Footprint Top View Solder Pad Plating 0.3 to 1.0 μm Gold over 1.27 to 8.89 μm Nickel Lid Plating 2.0 to 3.0 μm Nickel Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW B 1 3 6 919 YWWS A 2 5 E 4 D www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. G C F H 6 1 5 2 4 3 I J Page 5 of 6 SF2195E - 7/19/10 Tape and Reel Specifications Quantity Per Reel 7 178 500 13 330 3000 "B" REF. 100 REF. Inches “B” millimeters See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao Bo Ko Pitch W 2.0 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 3.35 mm 3.35 mm 1.40 mm 8.0 mm 12.0 mm Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B www.RFM.com E-mail: [email protected] ©2009-2010 by RF Monolithics, Inc. USER DIRECTION OF FEED Page 6 of 6 SF2195E - 7/19/10