Preliminary Data Sheet 16.0 Amps Glass Passivated Power STD Rectifiers Mechanical Dimensions Description 1 3 2 CASE Double Suffix D 1 3 1 2 CASE Common Anode Suffix A 2 CASE 3 Common Cathode Suffix C Dimensions in inchs TO-220AB Mechanical Dimensions Features Low forward voltage drop High current capability High reliability High surge current capability Weight: 2.24 grams Cases: TO-220AB molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: Leads solderable per MIL-STD202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260℃/10 seconds .16”,(4.06mm) from case. Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol FG FG FG FG FG FG FG Units Type Number 16A01 16A02 16A03 16A0416A05 16A06 16A07 Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 1000 V VRRM Maximum RMS Voltage 35 70 140 280 420 560 700 V VRMS Maximum DC Blocking Voltage 50 100 200 400 600 800 1000 V VDC Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @TC = 100℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @8.0A Maximum DC Reverse Current @ TC=25℃ at Rated DC Blocking Voltage @ TC=125℃ I(AV) 16.0 A IFSM 150 A VF 1.1 V 10 uA uA 250 Typical Junction Capacitance ( Note 1) Cj 50 pF Typical Thermal Resistance (Note 2) ℃/W RθJC 1.5 Operating and Storage Temperature Range TJ ,TSTG ℃ - 65 to + 150 Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 2. Thermal Resistance from Junction to Case Mounted on Heatsink size 2” x 3” x 0.25” Al-Plate IR Preliminary Data Sheet 16.0 Amps Glass Passivated Power STD Rectifiers RATINGS AND CHARACTERISTIC CURVES (FG16A01 THRU FG16A07) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 175 PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 18 16 14 Single Phase Half Wave 60Hz Resistive or Inductive Load 12 10 8 0 50 100 150 125 100 8.3ms Single Half Sine Wave JEDEC Method 75 50 25 0 1 150 2 5 o CASE TEMPERATURE. ( C) 20 50 FIG.4- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 400 100 INSTANTANEOUS REVERSE CURRENT. ( A) 100 10 1 o Tj=25 C Pulse Width=300 s 1% Duty Cycle 40 Tj=125 0C 10 4 2 1 Tj=25 0C 0.4 0.2 0.1 0.6 0.1 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 FORWARD VOLTAGE. (V) 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL JUNCTION CAPACITANCE PER LEG 120 JUNCTION CAPACITANCE.(pF) INSTANTANEOUS FORWARD CURRENT. (A) 10 NUMBER OF CYCLES AT 60Hz 100 80 60 40 f=10MHz Vsig=50mVp-p Tj=25 0C 20 0 0.1 0.4 1 4 10 40 REVERSE VOLTAGE. (V) 100 400 1000 140 100