ONSEMI XOCLCC6EVB

XOCLCC6EVB
Crystal Clock Oscillator
Module Evaluation Board
Manual for NBX Family in 6
Pin CLCC 5mm X 7mm
Package
http://onsemi.com
Generic Evaluation Board: XOCLCC6EVB
Devices: NBXxxxx
Prepared by: Senad Lomigora, Casey Stys
and Paul Shockman
Description
Evaluation Board Manual Document Features
This Evaluation Board manual (XOCLCC6EVB/D) is a
guide for using the XOCLCC6EVB Evaluation Board to
provide a convenient platform for quickly evaluating,
characterizing and verify performance and operation of a
device in the NBXxxxx family of Clock Oscillator Modules
packaged in the 6 pin CLCC, 5mm by 7 mm, CASE 848AB
(see Appendix).
This family of devices offer an internal crystal and PLL
IC. This Evaluation Board Manual and Evaluation Board
should be used in conjunction with a specific device data
sheet, which contains full technical details on specifications
and operation.
An NBXxxxx Clock Oscillator Module device may be
directly solder mounted onto the available evaluation board
footprint; or multiple units may be inserted and tested by
solder mounting a separate insertion socket (P/N
AM0393−320R from SER Electronics) onto the available
footprint.
•
•
•
•
•
•
•
Information on the XOCLCC6EVB Evaluation Board
Appropriate Lab Setup and Procedures
Board build Bill of Materials (Table 5)
Evaluation Board schematic (Figure 7)
Evaluation Board Lamination Stackup (Figure 8)
Evaluation Board Fabrication Notes
Appendix:
− MECHANICAL CASE OUTLINE
− GENERIC MARKING DIAGRAM
− SOLDERING FOOTPRINT
What measurements can you expect to make?
With this evaluation board, the following measurements
could be performed in single−ended or differential modes of
operation.
• DC Characteristics
• Frequency Performance
• Output Rise and Fall Time
• Phase Noise
• Jitter
Evaluation Board Features
• 6 pin CLCC solder footprint for solder mounting a
device or test socket
• Incorporates jumper headers to conveniently and
manually control the levels for the ’Output Enable’
(Pin 1) and ’Frequency Select’ (Pin 2) pins.
• Enable single or split−power supply operation.
LVPECL differential outputs are accessed via SMA
connectors offering different output load configurations.
Front
Back
Figure 1. Evaluation Board Images (Front and Back)
© Semiconductor Components Industries, LLC, 2008
September, 2008 − Rev. 1
1
Publication Order Number:
XOCLCC6EVB/D
XOCLCC6EVB
EVALUATION BOARD MAP
3
2
H
1
L
VDD
4
5
J1
OE
H
L
11
10
J2
FSEL
6
SMAGND
C3
7
C4
DUTGND
8
9
Figure 2. Evaluation Board Layout
Table 1. EVALUATION BOARD MAP DESCRIPTION
Number
Description
1
DUT PIN6 Positive supply connection anvil and test point.
2
Decoupling capacitors. See BOM/board schematic for details.
3
DUT PIN 4 OE jumper header to force logic HIGH (Active) or LOW (Outputs Disabled to High Impedance).
Leave open or use jumper to force HIGH (OE Pin defaults HIGH when left floating) (see Figure 3 below)
4
OE connection anvil and test point.
5
DUT PIN 2 FSEL jumper header to force logic HIGH or LOW. FSEL Pin defaults HIGH when left floating. (see
Figure 3 below)
6
FSEL connection anvil and test point.
7
Device ground (DUTGND) connection anvil and test point.
8
DUT PIN 3 GND/SMAGND jumper header to force DUTGND connection to SMAGND. (see Figure 3 below)
9
SMAGND connection anvil and test point.
10
SMA outputs (CLK/CLK).
11
6 pin CLCC 5mmX7mm DUT (Device under test).
http://onsemi.com
2
XOCLCC6EVB
Evaluation Board Jumper Headers on OE (Pin 4), FSEL (Pin 5)
Evaluation Board Jumper Header on DUTGND (Pin 3)
Figure 3. Select Positions for Evaluation Board Jumper Headers on OE (Pin 4), FSEL (Pin 5), and DUTGND (Pin 3)
TIME DOMAIN MEASUREMENTS
Equipment
Table 3. XOCLCC6EVB POWER SUPPLY
CONNECTION VOLTAGES
Table 2 indicates the recommended equipment for
making characterization and performance measurements.
Table 2. BASIC EQUIPMENT
Description
Example Equipment
Qty
Power Supply with 4
outputs
HP6624A or similar
1
Real−Time Oscilloscope
DPO70804 or similar
1
Matched High Speed
Cables with SMA
Connectors
Storm, Semflex, or
similar
2
Power supply cables
4
A). Single
Positive
+3.3 V Setup
B). Split 3.3 V
Setup
C). Single
Negative
−3.3 V Setup
VDD = 3.3 V
VDD = 2.0 V
VDD = 0 V
VTT
= VDD − 2.0 V
= 1.3 V
VTT
= VDD − 2.0 V
= SMAGND
=0V
VTT
= VDD − 2.0 V
= −2.0 V SMAGND
= VDD = 0 V
DUTGND
= SMAGND
=0V
DUTGND
= −1.3 V
DUTGND = −3.3 V
NOTE: SMAGND is the SMA cable shield reference for
the inputs and outputs only, not to be confused
with the device ground pin (DUTGND).
Setup
The following steps should be followed for proper
equipment setup.
Step 2: Connect Output Signals
Table 4 gives a list of specific LOGIC Levels and their
appropriate Power Supply and Typical Lab Setup
conditions
LVPECL: The LVPECL outputs have standard, open
emitter outputs and must be externally DC loaded and AC
terminated. A split power supply technique takes advantage
of terminating the LVPECL outputs into 50 W of an
oscilloscope or a frequency counter. Since VTT = VDD – 2 V,
offsetting VDD to +2.0 V yields VTT = 0 V or Ground
(SMAGND). The VTT terminal connects to the isolated
SMAGND connector ground plane, and is not to be
confused with the device ground pin (DUTGND). (See
Application Note AN8020/D for details on ECL
termination).
CML: For CML lab setup and test, operation with
negative supply voltage is recommended to enable the 50 W
internal impedance in the oscilloscope to be used as a
termination of the CML signals (VDD = 0.0 V, SMAGND =
0.0 V, and DUTGND = −3.3 V (See Application Note
AN8173/D for details on CML termination).
Step 1: Connect Power (split power supply mode)
Three power levels must be provided to the board: VDD,
DUTGND, and SMAGND via the test point anvils at the
edges of the board. Bypass capacitors are installed from
VDD to SMAGND and DUTGND to SMAGND near the test
points (see BOM). Devices may be tested in one of three
supply modes (see Table 3):
A). Single (Positive) +3.3 V Setup
No offset to supplies or output levels
B). Split 3.3 V Setup
Offsets the VDD, DUTGND, and output voltage levels by
−1.3 V and avoids an additional, separate VTT supply and
allows a direct connection to test equipment such as an
oscilloscope or counter with 50 W impedance to GND
inputs. SMAGND = VTT = VDD – 2.0 V = 0.0 V.
C). Single (Negative) −3.3 V Setup
Offsets the VDD, DUTGND, and output voltage levels by
−3.3 V
http://onsemi.com
3
XOCLCC6EVB
LVDS: Driver termination is a 100 W resistor across the
differential lines located at the receiver input.
Step 3: Configure FSEL and OE
The FSEL and OE control pins can be controlled from an
external source via the appropriate test point, or via the
jumper headers located on the evaluation board, as indicated
in Figures 2 and 7. Refer to the specific device datasheet for
details on the proper settings for these pins.
Table 4. TYPICAL LAB SETUP
LOGIC Levels
Power Supply
Typical Lab
Setup
LVPECL
Split 3.3 V
See Figure 4
CML
Single −3.3 V
See Figure 5
LVDS
Single 3.3 V
See Figure 6
+2.0V
Digital Oscilloscope
Or Frequency Counter
VDD = +2.0V
H
L
VDD
+
+2.0V
OE
−
H
J1
L
50W
Power Supply
FSEL
+
+1.3V
J2
SMAGND
−
50W
C3
C4
DUTGND
VEE = −1.3
−1.3
0V
Figure 4. Split Power Supply Lab Setup for LVPECL Outputs (DO NOT JUMPER DUTGND and SMAGND)
http://onsemi.com
4
XOCLCC6EVB
0V
0V
VDD = SMAGND = 0V
Digital Oscilloscope
Or Frequency Counter
H
L
VDD
+
0V
OE
−
H
J1
L
50W
Power Supply
+
FSEL
−3.3V
J2
SMAGND
−
C4
DUTGND
VEE = −3.3V
50W
C3
0V
−3.3V
Note: For CML outputs, 50 W to VDD is needed for proper termination. See application note AND8173/D.
Figure 5. Typical Lab Setup for CML Outputs (DO NOT JUMPER DUTGND and SMAGND)
+3.3V
H L
VDD
Power Supply
OE
Digital Oscilloscope
J1
H L
+
100W
+3.3V
High Impedance
Differential
Probe
−
FSEL
J2
SMAGND
C3
Jumper
C4
DUTGND
0V
Figure 6. Typical Lab Setup for LVDS Outputs (JUMPER DUTGND and SMAGND)
http://onsemi.com
5
XOCLCC6EVB
Table 5. XOCLCC6EVB EVALUATION BOARD BILL OF MATERIALS
Components
Manufacturer
Description
Part Number
Qty
Jumper Header
Berg
100 mil
In House
5
Test Point
Keystone
Anvil SMD
5016
3
Connector
Johanson
SMA, Edge Mount
142−0711−821
2
Capacitor
Kemet
22 mF, 10%
T491D22K016AS, Case C or D
2
Capacitor
Kemet
0.1 mF, 10%
C0603C104K4RAC
2
Socket (Not Supplied)
SER Electronics
Socket − 6−Lead 5mm x 7mm
AM0393−320R
1
Shunt
VDD
VDD
Jumper Header
Test
Point
Test
Point
VDD
OE
VDD
FSEL
CLK
GND
(DUTGND)
CLK
DUTGND
Test
Point
J1
SMA
Jumper Header
J2
DUTGND
SMA
Test
Point
VDD
DUTGND
Jumper Header
DUTGND
SMAGND
22mF
0.1mF
SMAGND
22mF
0.1mF
SMAGND
Figure 7. XOCLCC6EVB Evaluation Board Schematic
Figure 8. XOCLCC6EVB Evaluation Board Layer Lamination Stackup
http://onsemi.com
6
XOCLCC6EVB
Evaluation Board Fabrication Notes
1. MATERIAL: FR−4
2. FINISHED COPPER TO BE loz. (0.0014) EXTERNAL LAYERS
3. MINIMUM COPPER PLATING 0.0007” THICK FOR PLATED THRU HOLES ANNULAR RING TO BE 0.0002”
MINIMUM
4. LPI SOLDERMASK GREEN
5. SOLDERMASK REGISTRATION "0.002” N/A
6. ALL EXPOSED COPPER AREAS TO BE GOLD PLATED (0.000030” GOLD OVER 0.000100” NICKEL)
7. IF SPECIFIED, SILKSCREEN IS TO BE WHITE EPOXY INK.
8. HOLE DIAMETER TOLERANCE IS "0.002”, MAXIMUM LAYER TO LAYER MISREGISTRATION SHALL
BE 0.004”, MEASUREMENT METHOD MUST COMPLY WITH MIL−P−55110D, FIGURE 1.
9. FINISHED CONDUCTOR WIDTH SHALL NOT VARY MORE THAN "0.001” FROM ARTWORK MASTER
50 W TRACES ARE 0.024” WIDE.
10. WARP AND TWIST OF SINGLE SIDED BOARDS SHALL NOT EXCEED 0.002”PER INCH, WARP AND
TWIST OF MULTI−LAYER BOARDS SHALL NOT EXCEED 0.010” PER INCH.
11. ALL DIMENTIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED TOLERANCES. XX "0.010” XXX
"0.004”.
12. ACCEPTABILITY REQUIREMENTS PER IPC−A−600E.
13. DRAWING IS VIEWED FROM COMPONENT OR PRIMARY SIDE.
14. THIS IS A 4 LAYER BOARD.
15. ALL HOLES ARE PLATED THRU UNLESS OTHERWISE SPECIFIED.
16. DRILL SIZE UNITS ARE THOUSANDTHS OF AN INCH.
17. TRIM ALL SILKSCREEN WHICH FLOWS OVER VIA HOLES OR SMD PADS.
18. BREAK ALL SHARP EDGES, PCB EDGES SHOULD BE SMOOTH AND EVEN.
http://onsemi.com
7
XOCLCC6EVB
Appendix:
MECHANICAL CASE OUTLINE
GENERIC MARKING DIAGRAM
SOLDERING FOOTPRINT
PACKAGE DIMENSIONS
6 PIN CLCC, 7x5, 2.54P
CASE 848AB−01
ISSUE C
A
D
4X
0.15 C
E2
TERMINAL 1
INDICATOR
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
B
D1
H E1
DIM
A
A1
A2
A3
b
D
D1
D2
D3
E
E1
E2
E3
e
H
L
R
E
D2
TOP VIEW
A3
A2
0.10 C
A
SIDE VIEW
A1
C
SEATING
PLANE
2
3
R
0.05 C
e
6X
b
6
5
4
6X
1.17
XXXXX
A
WL
YY
WW
G
L
SOLDERING FOOTPRINT*
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
*This information is generic. Please refer
to device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present.
6X
2.54
PITCH
4.37
4.65
1
BOTTOM VIEW
1.50
6.17
6.66
XXXXXXXXX
XXXXXXXXXXXXX
AWLYYWWG
E3
0.10 C A B
0.08
1.30
MILLIMETERS
NOM
MAX
1.80
1.90
0.70 REF
0.36 REF
0.10
0.12
1.40
1.50
7.00 BSC
6.20
6.23
6.81
6.96
5.08 BSC
5.00 BSC
4.40
4.43
4.80
4.95
3.49 BSC
2.54 BSC
1.80 REF
1.27
1.37
0.70 REF
GENERIC
MARKING DIAGRAM*
D3
1
MIN
1.70
5.06
6X
1.50
DIMENSION: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
8
XOCLCC6EVB
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent
rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur.
Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury
or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an
Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
XOCLCC6EVB/D