AD UG-407

ADP2441-EVALZ User Guide
UG-407
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
ADP2441 Evaluation Board
FEATURES
GENERAL DESCRIPTION
Full-featured evaluation board for the ADP2441
Configurable synchronous step down dc-dc switching
regulator
Operating voltage range of board: VIN = 6 V to 36 V
Output voltage is set to 5 V or can be adjusted
Maximum load 1 A
Switching frequency set to 500 kHz or adjustable switching
frequency of 300 kHz to 1 MHz
Power saving mode at light load
Precision enable input pin
Current limit protection
Power good output
External soft start set to 6 ms or external tracking available
Board size: 53 mm × 53 mm
The ADP2441 evaluation board is a complete, dc-to-dc switching regulator design based on the ADP2441, a configurable, 1 A,
synchronous step-down, dc-to-dc regulator.
The ADP2441 is a synchronous, step-down dc-to-dc switching
regulator that uses a current mode pulse-width modulation
(PWM) control scheme at medium-to-heavy load currents for
high efficiency and smoothly transitions to a pulse skip mode
at light loads to conserve power. The power switch and
synchronous rectifier are integrated for minimal external part
count and high efficiency. The ADP2441 is optimized for
operation with small ferrite core inductors and ceramic
capacitors to deliver the maximum output power per square
millimeter of the PCB board area.
The ADP2441-EVALZ is available with 5 V at 1 A output,
switching frequency set to 500 kHz. If needed, the ADP2441
evaluation board configuration can be modified by changing
the values of the appropriate passive components.
DOCUMENTS NEEDED
ADP2441 data sheet
UG-407
Complete specifications for the ADP2441 device can be found
in the ADP2441 data sheet, which is available from Analog
Devices, Inc., and should be consulted in conjunction with this
user guide when using the evaluation board.
10694-101
ADP2441-EVALZ
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 12
UG-407
ADP2441-EVALZ User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Modifying the Evaluation Board .....................................................5
Documents Needed .......................................................................... 1
Changing the Output Voltage ......................................................5
General Description ......................................................................... 1
Changing the Switching Frequency ............................................5
ADP2441-EVALZ ............................................................................. 1
Changing the Soft Start Time ......................................................5
Revision History ............................................................................... 2
Typical Performance Characteristics ..............................................6
Using the Evaluation Board............................................................. 3
Evaluation Board Schematics and Artwork ...................................8
Powering Up the Evaluation Board ............................................ 3
Ordering Information .................................................................... 10
Measuring Evaluation Board Performance ............................... 4
Bill of Materials ........................................................................... 10
REVISION HISTORY
6/12—Initial Version: Revision 0
Rev. 0 | Page 2 of 12
ADP2441-EVALZ User Guide
UG-407
USING THE EVALUATION BOARD
PGOOD Signals
POWERING UP THE EVALUATION BOARD
When the output is enabled and the output voltage, VOUT, is in
regulation, the logic signal at the PGOOD test point is high. In
a typical application, a pull-up resistor from the PGOOD pin to
the external supply is used to generate this logic signal.
Input Power Source
The power source voltage must not exceed 36 V, the maximum
operation input voltage of the ADP2441.
Make sure the power source is switched off before connecting it
to the ADP2441 evaluation board. Connect the positive
terminal of the power source to the evaluation board VIN
terminal (T1), and the negative terminal of the power source to
the evaluation board GND terminal (T2). If the power source
includes an ammeter, connect the ammeter in series with the
input source voltage. Connect the positive lead (+) of the power
source to the ammeter positive (+) connection, the negative
lead (−) of the ammeter to the evaluation board VIN terminal
(T1), and the negative lead (−) of the power source to the
evaluation board GND terminal (T2).
Output Load
Make sure the evaluation board is switched off before connecting the load. Connect the load directly to the evaluation board,
with the positive (+) load connection to the VOUT terminal
(T3) and the negative (−) load connection to the GND terminal
(T4). If an ammeter is used, connect it in series with the load:
connect the positive (+) ammeter terminal to the evaluation
board VOUT terminal (T3), the negative (−) ammeter terminal
to the positive (+) load terminal, and the negative (−) load
terminal to the evaluation board GND terminal (T4).
On the evaluation board, the pull-up resistor (R7) is available to
connect to the external supply through the jumper (JP1). Test
Point TP2 is available to connect the external supply of 5 V.
PGOOD
R7
50kΩ
JP1
10694-001
The ADP2441 evaluation board is provided fully assembled
and tested. Before applying power to the evaluation board,
follow the procedures in this section.
TP2: EXTERNAL
SUPPLY: 5V
Figure 2 PGOOD Signal
External SS/Track Signal
The SS/TRK pin is multipurpose. It can be used either for
tracking the external supply or for soft start.
A header, TRK, is available on the board for connecting an
external signal to be tracked by the regulator output voltage.
Before applying a signal to the TRK header, make sure the
voltage divider resistor values (R10, R11) connected on the
evaluation board are the correct values (see the ADP2441
data sheet).
Alternatively, to program soft start time, a capacitor can be
connected to SS/TRK pin. On the evaluation board, a 10 nF
capacitor, C11, is connected for a soft start time of 6 ms.
Once the load is connected, make sure it is set to the proper
current before powering the ADP2441 evaluation board. Before
connecting a load to the output of the evaluation board, make
sure that the output voltage does not exceed the maximum
operating voltage range of the load.
SS
SS/TRK
C11
10nF
TRK
Enabling and Disabling the DC-to-DC Switching
Regulator
R11
OPEN
In the evaluation board, a voltage divider is used to generate
an enable signal for the IC. As soon as voltage is applied to
VIN (24 V), IC is enabled.
10694-002
R10
OPEN
Figure 3. Soft Start Signal
Alternatively, header TP1 (EN) is available to enable and disable
the evaluation board. To enable the output, connect the header
TP1 to the VIN supply or to an external voltage source. To disable
the output connect the header TP1 to the GND.
Rev. 0 | Page 3 of 12
UG-407
ADP2441-EVALZ User Guide
Measuring Line Regulation
MEASURING EVALUATION BOARD
PERFORMANCE
Output Voltage Ripple
To observe the output voltage ripple, place an oscilloscope
probe tip at Terminal T3 and connect the probe ground lead at
the negative (−) Terminal T4. Set the oscilloscope to an accoupled, 100 mV/division and 2 μs/division time base.
Switching Waveform
To observe the switching waveform with an oscilloscope, place
the oscilloscope probe tip at the end of the inductor that is
connected to the SW pin with the probe ground at Terminal T4,
GND. Set the scope to dc, 5 V/division, and 2 µs/division time
base. The switching waveform should alternate between 0 V
and approximately the input voltage.
Vary the input voltage and examine the change in the output
voltage. In PWM mode, the output voltage ripple should be
small (<50 mV) but in pulse skip mode, the output voltage
ripple can be as large as 100 mV.
Measuring Efficiency
The efficiency, η, is measured by comparing the input power
with the output power.
η=
VOUT × I OUT
VIN × I IN
Measure the input and output voltages as close as possible to the
input and output capacitors to reduce the effect of IR drops.
Inductor Current
The inductor current can be measured by removing one end
of the inductor from its pad and connecting a current loop in
series with it. Then a current probe can be used to measure
the current flowing through the current loop.
Line Transient Response
Generate a step input voltage (VIN) and observe the behavior
of the output voltage, with an oscilloscope.
Load Transient Response
10694-104
Generate a load current transient at the output, VOUT, and
observe the output voltage response with an oscilloscope.
Use a current probe attached to the wire between the output
and the load to visualize the current transient.
Loop Stability Measurement
Figure 4. Switch Node Measurement
Measuring Load Regulation
The load regulation should be measured by increasing the
load at the output and looking at the change in output voltage.
To minimize voltage drop, use short low-resistance wires,
especially for heavy loads.
Closed-loop response can be measured using a network
analyzer. To measure the loop response, Header IN and
Header OUT are available.
Rev. 0 | Page 4 of 12
ADP2441-EVALZ User Guide
UG-407
MODIFYING THE EVALUATION BOARD
Note that when the output voltage of ADP2441-EVALZ is
changed, the output capacitors (C7 and C8), inductor (L1), and
compensation components (R5 and C10) should be recalculated
and changed according to the Application Information section
in the ADP2441 data sheet to ensure stable operation.
The ADP2441 evaluation board is provided fully assembled
and tested for proper operation. The ADP2441-EVALZ has a
fixed 5 V output voltage.
CHANGING THE OUTPUT VOLTAGE
The ADP2441-EVALZ output regulation voltage is set by a
resistive voltage divider consisting of Resistors R2 and R3.
Resistor R2 corresponds to the RTOP resistor in the data sheet
and Resistor R3 corresponds to the RBOTTOM resistor in the data
sheet. The output regulation voltage is determined by the
equation
R2 + R3 
VOUT = 0.6 V × 
 R3 
Table 1. Programming Output Voltage
Voltage (V)
12
5
3.3
1.2
R2 (kΩ)
190
73
45
10
R3 (kΩ)
10
10
10
10
CHANGING THE SWITCHING FREQUENCY
where:
R2 is the value of the top resistor of the voltage divider (RTOP).
R3 is the value of the bottom resistor of the voltage divider
(RBOTTOM).
VOUT is the output regulation voltage in volts.
The switching frequency (fSW) set point can be changed by
replacing Resistor R9 with a different value using following
equation:
To set the output regulation voltage to the desired value, first
determine the value of the bottom resistor, R3, by
where:
R9 is the frequency resistor in kΩ.
fsw is the switching frequency in kHz.
R3 =
VFB
I STRING
where:
VFB = 0.6 V, the internal reference.
ISTRING is the resistor divider string current (greater than 20 μA
nominally).
Once R3 is determined, calculate the value of the top resistor,
R2, by
V
− VFB 
R2 = R3  OUT

V
FB


For example, to set the output regulation voltage of ADP2441EVALZ to 3.3 V, calculate the value of Resistors R2 and R3 as
shown in the following equations:
R3 =
I
VFB
STRING
=
0.6 V
60 μA
= 10 kΩ
V
− VFB 
R2 = R3 ×  OUT

V
FB


 3.3 V − 0.6 V 
= 10 kΩ × 
 = 45.3 k Ω
0.6V


R9 =
92,500
f SW
Table 2. Programming Frequency
R9 (kΩ)
308
132
92.5
Frequency (kHz)
300
700
1000
Note that when the switching frequency (fSW) is changed,
to ensure stable operation, the values of Inductor L1, C7, C8
(output capacitors), and R5, C10 (compensation components)
must be recalculated and changed (see the ADP2441 data sheet
for details on external component selection).
CHANGING THE SOFT START TIME
The soft start time of the ADP2441 on the evaluation board is
programmed to 6 ms. To change the soft start time, tSS, replace
Capacitor C11 with a different capacitor value using the
following equation:
C11 =
I SS
× t SS
VREF
where:
VREF is the internal reference voltage and equals 0.6 V.
ISS is the soft start current and equals 1 μA.
C11 is the soft start capacitor value.
tSS is the soft start time
Rev. 0 | Page 5 of 12
UG-407
ADP2441-EVALZ User Guide
TYPICAL PERFORMANCE CHARACTERISTICS
5.020
100
VIN = 12V
VIN = 24V
VIN = 36V
90
NO LOAD
LOAD 1A
5.015
80
5.010
60
VOUT (V)
EFFICIENCY (%)
70
50
40
30
5.005
5.000
4.995
20
4.990
0.1
4.985
10694-004
0
0.01
1
LOAD (A)
8
13
18
23
28
33
38
VIN (V)
Figure 5. Efficiency vs. Load Current, VOUT = 5 V, fSW = 500 kHz
10694-007
10
Figure 8. Line Regulation, VOUT = 5 V, fSW = 500 kHz
100
VIN = 5V
VIN = 12V
VIN = 24V
90
VOUT
80
1
EFFICIENCY (%)
70
60
INDUCTOR CURRENT
4
50
40
30
20
SW
10
0.1
1
LOAD (A)
CH1 100mV
Figure 6. Efficiency vs. Load Current, VOUT = 3.3 V, fSW = 500 kHz
CH2 10V
M20µs
CH4 500mA Ω T
46.8%
W
A CH4
150mA
Figure 9. Pulse Skip Waveform
VIN = 24 V; VOUT = 5 V, fSW = 500 kHz, No Load
VOUT
VIN = 12V
VIN = 24V
VIN = 36V
5.015
B
10694-008
0
0.01
10694-005
2
1
5.013
INDUCTOR CURRENT
5.009
5.007
SW
4
5.005
5.003
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
LOAD (A)
Figure 7. Load Regulation, VOUT = 5 V, fSW = 500 kHz
1.1
CH1 50mV
B
CH2 10V
M2µs
CH4 500mA Ω T
46.8%
W
A CH2
7.6V
10694-009
2
5.001
0.1
10694-006
VOUT (V)
5.011
Figure 10. PWM Waveform, VIN = 24 V, VOUT = 5 V, fSW = 500K, Load = 1 A
Rev. 0 | Page 6 of 12
ADP2441-EVALZ User Guide
UG-407
ENABLE
VOUT
1
2
VOUT
LOAD STEP 500mA
SS
PGOOD
4
1
SW
B
CH2 10V
M200µs
A CH4
CH4 500mA Ω T
71.2%
W
720mA
CH1 2V
CH3 2V
Figure 11. Load Transient, VIN = 24 V, VOUT = 5 V, 500 mA Step
W
CH2 5V
CH4 1V
M400µs
T
50.2%
A CH2
1.90V
Figure 14. Shutdown; VIN = 24 V, VOUT = 5 V, Load 5 Ω
VOUT
1
MAGNITUDE (dB)
LOAD STEP 500mA
4
B
10694-013
CH1 100mV
SW
110
200
90
160
70
120
50
80
30
40
10
0
–10
–40
–30
–80
–50
–120
–70
–160
PHASE (Degrees)
2
10694-010
4
4
B
M200µs
A CH4
CH2 5V
71.4%
CH4 500mA Ω T
W
800mA
–90
1k
VOUT
2
SS
4
PGOOD
W
CH2 2V
CH4 500mV
M2ms
T
10.6%
A CH2
1.92V
10694-012
3
B
–200
Figure 15. Bode Plot; VIN = 24 V, VOUT = 5 V, fSW = 500 kHz, Load = 1 A
fco = 37 kHz, Phase Margin = 55°
ENABLE
CH1 2V
CH3 2V
100k
FREQUENCY (Hz)
Figure 12. Load Transient, VIN = 12 V, VOUT = 5 V, 500 mA
1
10k
Figure 13. Startup; VIN = 24 V, VOUT = 5 V, Load 5 Ω
Rev. 0 | Page 7 of 12
10694-014
CH1 100mV
10694-011
2
UG-407
ADP2441-EVALZ User Guide
EVALUATION BOARD SCHEMATICS AND ARTWORK
10694-015
Figure 16.
Rev. 0 | Page 8 of 12
UG-407
Figure 19. Second layer
10694-019
10694-018
Figure 17. Top Layer
10694-017
10694-016
ADP2441-EVALZ User Guide
Figure 20. Bottom Layer
Figure 18. Third layer
Rev. 0 | Page 9 of 12
UG-407
ADP2441-EVALZ User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 3.
Qty
2
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
4
4
1
4
1
Reference Designator
C1, C2
C3, C4
C5
C7, C8
C11
L1
C6
C10
R1
R3, R8
R7
R2
R5
R6
R9
R10
R11
TRACK, SS, IN, OUT
TP1, TP2, TP3, TP4
JP1 PGOOD
T1, T2, T3, T4
U1
Description
Capacitor MLCC, 4.7 µF, 50 V,1206, X7R
Capacitor MLCC, 1 µF,25 V,0603, X7R
Capacitor, MLCC, 10 nF, 50 V,0603, X7R
Capacitor, MLCC, 22 µF, 25 V 1210, X7R
Capacitor 10 nF, 50 V ceramic X7R
MSS1038T-273
Capacitor MLCC, 0.1 µF, 50 V, 0603, X7R
Capacitor MLCC 270 pF, 50 V,0603, X7R
Resistor, 49.9 Ω, 1/10 W, 1% 0603 SMD
Resistor, 10 kΩ, 1/10 W, 1% 0603 SMD
Resistor, 50 kΩ, 1/10 W, 1% 0603 SMD
Resistor, 73.2 kΩ, 1/10 W, 1% 0603 SMD
Resistor, 118 kΩ, 1/10 W, 1% 0603 SMD
Resistor, 182 kΩ, 1/10 W, 1% 0603 SMD
Resistor, 185 kΩ, 1/10 W, 1% 0603 SMD
Resistor, 0 Ω, 1/10 W, 1% 0603 SMD
Resistor, open, 1/10 W, 1% 0603 SMD
Headers
Headers
Jumper
Terminal, double turret, brass, 0.078”
ADP2441
Rev. 0 | Page 10 of 12
Manufacturer/Part Number
Murata GRM31CR71H475KA12L
Murata GRM188R71E105KA12D
Murata GRM188R71H103KA01D
Murata GRM32ER71E226K
Panasonic ECJ-1VB1H103K
Coilcraft Coilcraft
Murata GRM188R71H104KA93D
Murata
Determined by user
Determined by user
Determined by user
Determined by user
Determined by user
Determined by user
Determined by user
Determined by user
Determined by user
Sullins PBC01SAAN
Sullins PBC01SAAN
Sullins PBC03SAAN
Keystone 1502-1
Analog Devices ADP2441
ADP2441-EVALZ User Guide
UG-407
NOTES
Rev. 0 | Page 11 of 12
UG-407
ADP2441-EVALZ User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG10694-0-6/12(0)
Rev. 0 | Page 12 of 12