CYPRESS CY22E016L

CY22E016L
16 Kbit (2K x 8) nvSRAM
Features
Functional Description
■
25 ns, 35 ns and 45 ns access times
■
Hands off automatic STORE on power down with external
68 μF capacitor
■
STORE to QuantumTrap™ non-volatile elements is initiated
by hardware or AutoStore on power down
■
RECALL to SRAM is initiated on power up
■
Infinite READ, WRITE, and RECALL cycles
■
10 mA typical ICC at 200 ns cycle time
■
1,000,000 STORE cycles to QuantumTrap
The Cypress CY22E016L is a fast static RAM with a
non-volatile element incorporated in each static memory cell.
The SRAM is read and written an infinite number of times,
while independent, non-volatile data resides in non-volatile
elements. Data transfers from the SRAM to the non-volatile
elements (the STORE operation) takes place automatically on
power down. A 68 μF or larger capacitor tied from VCAP to
ground guarantees the STORE operation, regardless of power
down slew rate or loss of power from “hot swapping.” Transfers
from the non-volatile elements to the SRAM (the RECALL
operation) take place automatically on restoration of power. A
hardware STORE is initiated with the HSB pin.
■
100 year data retention to QuantumTrap
■
Single 5V operation +10%
■
Commercial and industrial temperature
■
SOIC package
■
RoHS compliance
Logic Block Diagram
VCC
Quantum Trap
32 X 512
A5
A8
A9
STATIC RAM
ARRAY
32 X 512
DQ 0
DQ 2
DQ 3
DQ 4
DQ 5
DQ 6
RECALL
STORE/
RECALL
CONTROL
HSB
COLUMN I/O
INPUT BUFFERS
DQ 1
POWER
CONTROL
STORE
ROW DECODER
A6
A7
VCAP
COLUMN DEC
A 0 A 1 A 2 A 3 A 4 A 10
DQ 7
OE
CE
WE
Cypress Semiconductor Corporation
Document Number: 001-06727 Rev. *D
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised August 1, 2007
[+] Feedback
CY22E016L
Pin Configurations
V CC
V CAP
1
28
NC
2
27
WE
A7
3
26
HSB
A6
4
25
A8
A5
5
24
A9
A4
6
A3
7
A2
8
A1
9
28-SOIC
23
NC
Top View
22
OE
(Not To Scale)
21
A 10
20
CE
A0
10
19
DQ7
DQ0
11
18
DQ6
DQ1
12
17
DQ5
DQ2
13
16
DQ4
V SS
14
15
DQ3
Pin Definitions
Pin Name
IO Type
A0–A10
Input
Description
Address Inputs. Used to select one of the 2,048 bytes of the nvSRAM.
DQ0-DQ7 Input/Output Bidirectional Data IO lines. Used as input or output lines depending on operation.
WE
Input
Write Enable Input, Active LOW. When selected LOW, this writes data on the IO pins to the address
location latched by the falling edge of CE.
CE
Input
Chip Enable Input, Active LOW. When LOW, selects the chip. When HIGH, deselects the chip.
OE
Input
Output Enable, Active LOW. The active LOW OE input enables the data output buffers during read
cycles. Deasserting OE HIGH causes the IO pins to tri-state.
VSS
Ground
VCC
HSB
VCAP
NC
Ground for the Device. Is connected to ground of the system.
Power Supply Power Supply Inputs to the Device.
Input/Output Hardware Store Busy (HSB). When LOW, this output indicates a Hardware Store is in progress.
When pulled low external to the chip, it initiates a non-volatile STORE operation. A weak internal pull
up resistor keeps this pin HIGH if not connected (connection optional).
Power Supply AutoStore Capacitor. Supplies power to nvSRAM during power loss to store data from SRAM to
non-volatile elements.
No Connect No Connects. This pin is not connected to the die.
Document Number: 001-06727 Rev. *D
Page 2 of 14
[+] Feedback
CY22E016L
Figure 1. AutoStore Mode
1
28
27
10k Ohm
The CY22E016L nvSRAM is made up of two functional components paired in the same physical cell. These are an SRAM
memory cell and a non-volatile QuantumTrap cell. The SRAM
memory cell operates as a standard fast static RAM. Data in the
SRAM is transferred to the non-volatile cell (the STORE
operation) or from the non-volatile cell to SRAM (the RECALL
operation). This unique architecture enables storage and recall
of all cells in parallel. During the STORE and RECALL operations, SRAM READ and WRITE operations are inhibited. The
CY22E016L supports infinite reads and writes similar to a typical
SRAM. In addition, it provides infinite RECALL operations from
the non-volatile cells and up to one million STORE operations.
on the stored system charge as power goes down. The user
must, however, guarantee that VCC does not drop below 3.6V
during the 10 ms STORE cycle..
10k Ohm
Device Operation
26
0.1U F
Bypass
The CY22E016L performs a READ cycle whenever CE and OE
are LOW while WE and HSB are HIGH. The address specified
on pins A0–10 determines which of the 2,048 data bytes are
accessed. When the READ is initiated by an address transition,
the outputs are valid after a delay of tAA (READ cycle 1). If the
READ is initiated by CE or OE, the outputs are valid at tACE or at
tDOE, whichever is later (READ cycle 2). The data outputs
repeatedly respond to address changes within the tAA access
time without the need for transitions on any control input pins,
and remains valid until another address change or until CE or OE
is brought HIGH, or WE or HSB is brought LOW.
68 UF
6v, +20%
SRAM Read
14
15
SRAM Write
1
28
27
10k Ohm
Figure 2. System Power Mode
10k Ohm
A WRITE cycle is performed whenever CE and WE are LOW and
HSB is HIGH. The address inputs are stable prior to entering the
WRITE cycle and must remain stable until either CE or WE goes
HIGH at the end of the cycle. The data on the common IO pins
IO0–7 is written into the memory if it is valid tSD, before the end
of a WE controlled WRITE or before the end of an CE controlled
WRITE. Keep OE HIGH during the entire WRITE cycle to avoid
data bus contention on common IO lines. If OE is left LOW,
internal circuitry turns off the output buffers tHZWE after WE goes
LOW.
26
During normal AutoStore operation, the CY22E016L draws
current from VCC to charge a capacitor connected to the VCAP
pin. This stored charge is used by the chip to perform a single
STORE operation. After power up, when the voltage on the VCAP
pin drops below VSWITCH, the part automatically disconnects the
VCAP pin from VCC and initiates a STORE operation.
Figure 1 shows the proper connection of the storage capacitor
(VCAP) for automatic store operation. A charge storage capacitor,
having a capacity of between 68 μF and 220 μF (±20%) rated at
6V, is provided. In system power mode, both VCC and VCAP are
connected to the +5V power supply without the 68 μF capacitor.
In this mode, the AutoStore function of the CY22E016L operates
Document Number: 001-06727 Rev. *D
0.1U F
Bypass
AutoStore Operation
14
15
Page 3 of 14
[+] Feedback
CY22E016L
If an automatic STORE on power loss is not required, then VCC
is tied to ground and +5V is applied to VCAP. This is the AutoStore
Inhibit mode where the AutoStore function is disabled. If the
CY22E016L is operated in this configuration, references to VCC
are changed to VCAP throughout this datasheet. In this mode,
STORE operations are triggered with the HSB pin. It is not
permissible to change between these three options at will.
To prevent unneeded STORE operations, automatic STOREs
and those initiated by externally driving HSB LOW are ignored,
unless at least one WRITE operation takes place since the most
recent STORE or RECALL cycle. An optional pull up resistor is
shown connected to HSB. This is used to signal the system that
the AutoStore cycle is in progress.
Figure 3. AutoStore Inhibit Mode
During any STORE operation, regardless of how it is initiated,
the CY22E016L continues to drive the HSB pin LOW, releasing
it only when the STORE is complete. After completing the
STORE operation, the CY22E016L remains disabled until the
HSB pin returns HIGH.
27
Hardware RECALL (Power Up)
10k Ohm
28
10k Ohm
If HSB is not used, it is left unconnected.
0.1U F
Bypass
1
pin is connected together to the HSB pins from the other
CY22E016L. An external pull up resistor to +5V is required, since
HSB acts as an open drain pull down. The VCAP pins from the
other CY22E016L parts are tied together and share a single
capacitor. The capacitor size is scaled by the number of devices
connected to it. When any one of the CY22E016L detects a
power loss and asserts HSB, the common HSB pin causes all
parts to request a STORE cycle. (A STORE takes place in those
CY22E016L that are written since the last non-volatile cycle.)
26
During power up or after any low power condition (VCC <
VSWITCH), an internal RECALL request is latched. When VCC
once again exceeds the sense voltage of VSWITCH, a RECALL
cycle is automatically initiated and takes tHRECALL to complete.
Data Protection
The CY22E016L protects data from corruption during low
voltage conditions by inhibiting all externally initiated STORE
and WRITE operations. The low voltage condition is detected
when VCC is less than VSWITCH. If the CY22E016L is in a WRITE
mode (both CE and WE are LOW) at power up after a RECALL
or after a STORE, the WRITE is inhibited until a negative
transition on CE or WE is detected. This protects against
inadvertent writes during power up or brown out conditions.
Noise Considerations
14
15
Hardware STORE (HSB) Operation
The CY22E016L provides the HSB pin for controlling and
acknowledging the STORE operations. The HSB pin is used to
request a hardware STORE cycle. When the HSB pin is driven
low, the CY22E016L conditionally initiates a STORE operation
after tDELAY. An actual STORE cycle begins if a WRITE to the
SRAM took place since the last STORE or RECALL cycle. The
HSB pin also acts as an open drain driver that is internally driven
low to indicate a busy condition, while the STORE (initiated by
any means) is in progress.
SRAM READ and WRITE operations that are in progress when
HSB is driven low by any means are given time to complete
before the STORE operation is initiated. After HSB goes low, the
CY22E016L continues SRAM operations for tDELAY. During
tDELAY, multiple SRAM READ operations take place. If a WRITE
is in progress when HSB is pulled LOW, it is allowed a time,
tDELAY, to complete. However, any SRAM WRITE cycles
requested after HSB goes LOW are inhibited until HSB returns
HIGH.
The HSB pin is used to synchronize multiple CY22E016L while
using a single larger capacitor. To operate in this mode, the HSB
Document Number: 001-06727 Rev. *D
The CY22E016L is a high speed memory. It must have a high
frequency bypass capacitor of approximately 0.1 µF connected
between VCC and VSS, using leads and traces that are as short
as possible. As with all high speed CMOS ICs, careful routing of
power, ground, and signals reduces circuit noise.
Low Average Active Power
CMOS technology provides the CY22E016L the benefit of
drawing significantly less current when it is cycled at times longer
than 50 ns. Figure 4 shows the relationship between ICC and
READ/WRITE cycle time. Worst case current consumption is
shown for both CMOS and TTL input levels (commercial temperature range, VCC = 5.5V, 100% duty cycle on chip enable). Only
standby current is drawn when the chip is disabled. The overall
average current drawn by the CY22E016L depends on the
following items:
1. The duty cycle of chip enable
2. The overall cycle rate for accesses
3. The ratio of READs to WRITEs
4. CMOS vs. TTL input levels
5. The operating temperature
6. The VCC level
7. IO loading
Page 4 of 14
[+] Feedback
CY22E016L
Preventing STOREs
VCC connected to VCC and a 68 μF capacitor on VCAP) and VCC
crosses VSWITCH on the way down, the CY22E016L attempts to
pull HSB LOW; if HSB does not actually get below VIL, the part
stops trying to pull HSB low and abort the STORE attempt.
The STORE function is disabled by holding HSB HIGH with a
driver capable of sourcing 30 mA at a VOH of at least 2.2V,
because it has to overpower the internal pull down device. The
device drives HSB low for 20 ns at the onset of a STORE. When
the CY22E016L is connected for AutoStore operation (system
Table 1. Hardware Mode Selection
CE
WE
HSB
A10–A0
Mode
IO
Power
H
X
H
X
Not Selected
Output High Z
Standby
L
H
H
X
Read SRAM
Output Data
Active
L
L
H
X
Write SRAM
Input Data
Active
X
X
L
X
Non-volatile
STORE
Output High Z
ICC2
Figure 4. Current versus Cycle Time (READ)
Document Number: 001-06727 Rev. *D
Figure 5. Current versus Cycle Time (WRITE)
Page 5 of 14
[+] Feedback
CY22E016L
Maximum Ratings
Package Power Dissipation
Capability (TA = 25°C) ................................................... 1.0W
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
Surface Mount Lead Soldering
Temperature (3 Seconds) .......................................... +260°C
Storage Temperature ................................. –65°C to +150°C
Output Short Circuit Current [1] .................................... 15 mA
Ambient Temperature with
Power Applied ............................................ –55°C to +125°C
Static Discharge Voltage.......................................... > 2001V
(MIL-STD-883, Method 3015)
Supply Voltage on VCC Relative to GND ..........–0.5V to 7.0V
Latch up Current.................................................... > 200 mA
Voltage Applied to Outputs
in High Z State ....................................... –0.5V to VCC + 0.5V
Operating Range
Input Voltage.............................................–0.5V to Vcc+0.5V
Range
Transient Voltage (greater than 20 ns) on
Any Pin to Ground Potential .................. –0.5V to VCC + 2.0V
Commercial
Industrial
Ambient Temperature
VCC
0°C to +70°C
4.5V to 5.5V
-40°C to +85°C
DC Electrical Characteristics
Over the Operating Range (VCC = 4.5V to 5.5V) [2]
Parameter
ICC1
Description
Average VCC Current
Test Conditions
Min
Max
Unit
Commercial
tRC = 25 ns
tRC = 35 ns
tRC = 45 ns
Dependent on output loading and cycle rate.
Industrial
Values obtained without output loads. IOUT = 0mA.
85
75
65
mA
mA
mA
75
mA
ICC2
Average VCC Current
during STORE
All Inputs Do Not Care, VCC = Max
Average current for duration tSTORE
3
mA
ICC3
Average VCC Current at WE > (VCC – 0.2). All other inputs cycling.
tAVAV = 200 ns, 5V, 25°C Dependent on output loading and cycle rate. Values obtained
without output loads.
Typical
10
mA
ICC4
Average VCAP Current All Inputs Do Not Care, VCC = Max
during AutoStore Cycle Average current for duration tSTORE
2
mA
ISB
VCC Standby Current
2.5
mA
IILK
-1
+1
μA
IOLK
Input Leakage Current VCC = Max, VSS < VIN < VCC
Off State Output
VCC = Max, VSS < VIN < VCC, CE or OE > VIH
Leakage Current
-5
+5
μA
VIH
Input HIGH Voltage
2.2
VCC + 0.5
V
VIL
Input LOW Voltage
VSS – 0.5
0.8
VOH
Output HIGH Voltage
IOUT = –4 mA except HSB
VOL
Output LOW Voltage
IOUT = 8 mA except HSB
0.4
V
VBL
Logic’0’ on HSB
IOUT = 3 mA
0.4
V
CE > (VCC – 0.2). All others VIN < 0.2V or > (VCC – 0.2V). Standby
current level after non-volatile cycle is complete.
Inputs are static. f = 0 MHz.
2.4
V
V
Notes
1. Outputs shorted for no more than one second. No more than one output shorted at a time.
2. Typical conditions for the Active Current shown on the front page of the datasheet are average values at 25°C (room temperature) and VCC = 5V. Not 100% tested.
Document Number: 001-06727 Rev. *D
Page 6 of 14
[+] Feedback
CY22E016L
Capacitance
These parameters are guaranteed but not tested.
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Test Conditions
Max
Unit
8
pF
7
pF
Test Conditions
28-SOIC
Unit
Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA / JESD51.
TBD
°C/W
TBD
°C/W
TA = 25°C, f = 1 MHz,
VCC = 0 to 3.0 V
Thermal Resistance
These parameters are guaranteed but not tested.
Parameter
ΘJA
ΘJC
Description
Thermal Resistance
(Junction to Ambient)
Thermal Resistance
(Junction to Case)
AC Test Loads
R1 963Ω
R1 963Ω
5.0V
For Tri-state
Specifications
5.0V
Output
Output
30 pF
R2
512Ω
5 pF
R2
512Ω
AC Test Conditions
Input Pulse Levels.................................................... 0V to 3V
Input Rise and Fall Times (10% - 90%)........................ <5 ns
Input and Output Timing Reference Levels.....................1.5V
Document Number: 001-06727 Rev. *D
Page 7 of 14
[+] Feedback
CY22E016L
AC Switching Characteristics
Parameter
25 ns Part
Cypress
Alt.
Parameter Parameter
Description
Min
Max
35 ns Part
Min
45 ns Part
Max
Min
Unit
Max
SRAM Read Cycle
tACE
tACS
Chip Enable Access Time
tRC
[4]
tRC
Read Cycle Time
tAA
[5]
tAA
Address Access Time
25
35
45
ns
tOE
Output Enable to Data Valid
10
15
20
ns
tDOE
[5]
25
25
35
45
35
ns
45
ns
tOH
Output Hold After Address Change
5
5
5
ns
tLZCE
[6]
tLZ
Chip Enable to Output Active
5
5
5
ns
tHZCE
[6]
tOHA
tHZ
Chip Disable to Output Inactive
tLZOE [6]
tOLZ
Output Enable to Output Active
[6]
tOHZ
Output Disable to Output Inactive
tPU
[3]
tPA
Chip Enable to Power Active
tPD
[ 3]
tPS
Chip Disable to Power Standby
tHZOE
10
0
13
15
0
10
0
ns
0
13
ns
15
0
ns
0
25
35
ns
45
ns
SRAM Write Cycle
tWC
tWC
Write Cycle Time
25
35
45
ns
tPWE
tWP
Write Pulse Width
20
25
30
ns
tSCE
tCW
Chip Enable to End of Write
20
25
30
ns
tSD
tDW
Data Setup to End of Write
10
12
15
ns
tHD
tDH
Data Hold After End of Write
0
0
0
ns
tAW
tAW
Address Setup to End of Write
20
25
30
ns
tSA
tAS
Address Setup to Start of Write
0
0
0
ns
tHA
tWR
Address Hold After End of Write
0
0
0
ns
tWZ
Write Enable to Output Disable
tOW
Output Active After End of Write
tHZWE [6,7]
tLZWE
[6]
10
5
13
14
5
ns
5
ns
AutoStore Power Up RECALL
Parameter
tHRECALL [8]
tSTORE
[9]
Description
CY22E016L
Min
Power up RECALL Duration
STORE Cycle Duration
tDELAY
Time Allowed to Complete SRAM Cycle
VSWITCH
Low Voltage Trigger Level
VRESET
Low Voltage Reset Level
Max
550
μs
10
ms
μs
1
4.0
Unit
4.5
V
3.6
V
Notes
3. These parameters are guaranteed but not tested.
4. IWE must be HIGH during SRAM Read Cycles.
5. Device is continuously selected with CE and OE both Low.
6. Measured ±200 mV from steady state output voltage.
7. If WE is Low when CE goes Low, the outputs remain in the high impedance state.
8. tHRECALL starts from the time VCC rises above VSWITCH.
9. If an SRAM Write has not taken place since the last non-volatile cycle, no STORE will take place
Document Number: 001-06727 Rev. *D
Page 8 of 14
[+] Feedback
CY22E016L
Hardware STORE Cycle
Parameter
CY22E016L
Description
tSTORE [6]
STORE Cycle Duration
tDELAY [10]
Time Allowed to Complete SRAM Cycle
tRESTORE [11]
Hardware STORE High to Inhibit Off
tHLHX
Hardware STORE Pulse Width
tHLBL
Hardware STORE Low to STORE Busy
Min
Max
10
1
Unit
ms
ms
700
15
ns
ns
300
ns
Switching Waveforms
Figure 6. SRAM Read Cycle Number 1: Address Controlled [3, 5, 12]
tRC
ADDRESS
t AA
t OH
DQ (DATA OUT)
DATA VALID
Figure 7. SRAM Read Cycle Number 2: CE Controlled [3,12]
tRC
ADDRESS
tLZCE
CE
tACE
tPD
tHZCE
OE
tLZOE
DQ (DATA OUT)
t PU
ICC
tHZOE
tDOE
DATA VALID
ACTIVE
STANDBY
Notes
10. Read and Write cycles in progress before HSB are given this amount of time to complete.
11. tRESTOREis only applicable after tSTORE is complete.
12. HSB must remain HIGH during READ and WRITE cycles.
Document Number: 001-06727 Rev. *D
Page 9 of 14
[+] Feedback
CY22E016L
Switching Waveforms (continued)
Figure 9. SRAM Write Cycle Number 1: WE Controlled [12,13]
tWC
ADDRESS
tHA
tSCE
CE
tAW
tSA
tPWE
WE
tSD
tHD
DATA VALID
DATA IN
tHZWE
DATA OUT
tLZWE
HIGH IMPEDANCE
PREVIOUS DATA
Figure 8. SRAM Write Cycle Number 2: CE Controlled
tWC
ADDRESS
CE
WE
tHA
tSCE
tSA
tAW
tPWE
tSD
DATA IN
DATA OUT
tHD
DATA VALID
HIGH IMPEDANCE
Note
13. CE or WE is less thanVIH during address transitions.
Document Number: 001-06727 Rev. *D
Page 10 of 14
[+] Feedback
CY22E016L
Switching Waveforms (continued)
Figure 10. AutoStore or Power Up RECALL
VCC
VSWITCH
VRESET
AutoStore
POWER-UP RECALL
tRESTORE
tVSBL
tSTORE
HSB
tDELAY
DQ (DATA OUT)
POWER UP
RECALL
BROWN OUT
NO STROKE
BROWN OUT
AutoStore TM
BROWN OUT
AutoStore TM
NO RECALL
(VCC DID NOT GO
BELOW VRESET)
NO RECALL
(VCC DID NOT GO
BELOW VRESET)
RECALL WHEN
VCC RETURNS
ABOVE VSWITCH
(NO SRAM WRITES)
Figure 11. Hardware STORE Cycle
tSTORE
tHLBL
a
a
HSB (OUT)
tHLHX
a
a
HSB (IN)
HIGH IMPEDANCE
HIGH IMPEDANCE
DQ (DATA OUT)
DATA VALID
Document Number: 001-06727 Rev. *D
a
a
t DELAY
DATA VALID
Page 11 of 14
[+] Feedback
CY22E016L
Part Numbering Nomenclature
CY 22 E 016 L- SZ 25 X C T
Option:
T-Tape and Reel
Blank - Std.
Temperature:
C - Commercial (0 to 70°C)
I - Industrial (-40°C to 85°C)
Speed:
25 - 25 ns
35 - 35 ns
45 - 45 ns
Pb-Free
Package:
SZ - 28-SOIC
Data Bus:
L - x8
Density:
016 - 16 Kb
Voltage:
E - 5.0V
nvSRAM
22 - AutoStore + Hardware Store
Cypress
Document Number: 001-06727 Rev. *D
Page 12 of 14
[+] Feedback
CY22E016L
Ordering Information
All the parts below are Pb-Free.
Speed
(ns)
25
25
35
35
45
45
Ordering Code
Package
Name
CY22E016L-SZ25XCT
51-85026
28-pin SOIC
CY22E016L-SZ25XC
51-85026
28-pin SOIC
CY22E016L-SZ25XIT
51-85026
28-pin SOIC
CY22E016L-SZ25XI
51-85026
28-pin SOIC
CY22E016L-SZ35XCT
51-85026
28-pin SOIC
Operating
Range
Package Type
CY22E016L-SZ35XC
51-85026
28-pin SOIC
CY22E016L-SZ35XIT
51-85026
28-pin SOIC
CY22E016L-SZ35XI
51-85026
28-pin SOIC
CY22E016L-SZ45XCT
51-85026
28-pin SOIC
CY22E016L-SZ45XC
51-85026
28-pin SOIC
CY22E016L-SZ45XIT
51-85026
28-pin SOIC
CY22E016L-SZ45XI
51-85026
28-pin SOIC
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Package Diagrams
28-Pin(300 Mil) Molded SOIC
NOTE :
PIN 1 ID
1. JEDEC STD REF MO-119
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH,BUT
14
DOES INCLUDE MOLD MISMATCH AND ARE MEASURED AT THE MOLD PARTING LINE.
1
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.010 in (0.254 mm) PER SIDE
3. DIMENSIONS IN INCHES
0.291[7.39]
MIN.
MAX.
4. PACKAGE WEIGHT 0.85gms
0.300[7.62]
0.394[10.01]
*
0.419[10.64]
15
28
PART #
S28.3 STANDARD PKG.
SZ28.3 LEAD FREE PKG.
0.026[0.66]
0.032[0.81]
SEATING PLANE
0.697[17.70]
0.713[18.11]
0.092[2.33]
0.105[2.67]
0.004[0.10]
0.050[1.27]
0.013[0.33]
0.004[0.10]
0.019[0.48]
0.0118[0.30]
*
0.015[0.38]
0.050[1.27]
0.0091[0.23]
0.0125[3.17]
*
TYP.
51-85026-*D
Document Number: 001-06727 Rev. *D
Page 13 of 14
[+] Feedback
CY22E016L
Document History Page
Document Title: CY22E016L 16 Kbit (2K x 8) nvSRAM
Document Number: 001-06727
REV.
ECN NO.
Issue
Date
Orig. of
Change
**
427789
See ECN
TUP
Description of Change
New datasheet
*A
437321
See ECN
TUP
Show datasheet on external Web
*B
472053
See ECN
TUP
Updated Part Numbering Nomenclature and Ordering Information
*C
503290
See ECN
PCI
Converted from Advance to Preliminary
Changed the term “Unlimited” to “Infinite”
Removed Industrial Grade mention
Corrected VIL min specification from (VCC - 0.5) to (VSS - 0.5)
Updated Part Nomenclature Table and Ordering Information Table
*D
1349963
See ECN
UHA/SFV
Changed from Preliminary to Final. Updated AC Test Conditions.
Updated Ordering Information Table
© Cypress Semiconductor Corporation, 2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any
circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical,
life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical
components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-06727 Rev. *D
Revised August 1, 2007
Page 14 of 14
PSoC Designer™, Programmable System-on-Chip™, and PSoC Express™ are trademarks and PSoC® is a registered trademark of Cypress Semiconductor Corp. All other trademarks or registered
trademarks referenced herein are property of the respective corporations. Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the
Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. AutoStore and QuantumTrap are
registered trademarks of Simtek Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback