RS2A THRU RS2M SURFACE MOUNT FAST RECOVERY RECTIFIER Reverse Voltage - 50 to 1000 Volts FEATURES DO-214AA (HSMB) (Round Lead) The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 For surface mounted applications Low reverse leakage Built-in strain relief,ideal for automated placement High forward surge current capability High temperature soldering guaranteed: 250 C/10 seconds at terminals Glass passivated chip junction H Cathode Band J A E C D Forward Current - 2.0 Ampere B F MECHANICAL DATA G DIMENSIONS INCHES DIM A B C D E F G H J MIN .078 .075 .002 ----.035 .065 .205 .160 .130 Case : JEDEC DO-214AA molded plastic body over passivated chip Terminals : Solder plated, solderable per MIL-STD-750, Method 2026 Polarity : Color band denotes cathode end Mounting Position : Any Weight :0.005 ounce, 0.138 grams MM MAX .116 .089 .008 .02 .055 .091 .224 .180 .155 MIN 1.98 1.90 .05 ----.90 1.65 5.21 4.06 3.30 MAX 2.95 2.25 .20 .51 1.40 2.32 5.69 4.57 3.94 NOTE MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. MDD Catalog Number SYMBOLS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TL=90 C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 2.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=125 C Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range VRRM VRMS VDC RS2A RS2B RS2D RS2G RS2J 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 RS2K RS2M UNITS 800 560 800 VOLTS VOLTS VOLTS 1000 700 1000 I(AV) 2.0 Amp IFSM 50.0 Amps VF 1.3 Volts IR 5.0 200.0 µA trr 150 CJ RθJA TJ,TSTG Note:1.Reverse recovery condition IF=0.5A,IR=1.0A,Irr=0.25A 2.Measured at 1MHz and applied reverse voltage of 4.0V D.C. 3.P.C.B. mounted with 0.2x0.2”(5.0x5.0mm) copper pad areas MDD ELECTRONIC 250 40.0 15.0 -50 to +150 500 ns pF C/W C RATINGS AND CHARACTERISTIC CURVES RS2A THRU RS2M Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve 10 3.0 6 4 2.5 2 25°C Amps 2.0 1 .6 1.5 Amps .4 1.0 .2 .5 .1 Single Phase, Half Wave 60Hz Resistive or Inductive Load .06 0 .04 0 50 75 100 125 150 175 °C .02 .01 .4 .6 .8 1.0 1.2 Average Forward Rectified Current - Amperesversus Ambient Temperature -°C 1.4 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25°C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 Junction Capacitance - pFversus Reverse Voltage - Volts MDD ELECTRONIC 200 400 1000 RATINGS AND CHARACTERISTIC CURVES RS2A THRU RS2M Figure 4 Maximum Non-Repetitive Forward Surge Current 90 75 60 45 Amps 30 15 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 5 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω -0.25 Oscilloscope Note 1 -1.0 1cm Set Time Base for 20/100ns/cm Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive MDD ELECTRONIC