ER2A THRU ER2J SURFACE MOUNT SUPERFAST RECTIFIER VOLTAGE - 50 to 600 Volts CURRENT - 2.0 Amperes FEATURES l For surface mounted applications l Low profile package l l Built-in strain relief Easy pick and place l l Superfast recovery times for high efficiency Plastic package has Underwriters Laboratory l Flammability Classification 94V-O Glass passivated junction l SMB/DO-214AA High temperature soldering: 260 ¢J /10 seconds at terminals MECHANICAL DATA Case: JEDEC DO-214AA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard packaging: 12mm tape (EIA-481) Weight: 0.003 ounce, 0.093 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at TL=110 ¢J Peak Forward Surge Current 8.3ms single half sinewave superimposed on rated load(JEDEC method) Maximum Instantaneous Forward Voltage at 2.0A Maximum DC Reverse Current TA=25 ¢J At Rated DC Blocking Voltage TA=100 ¢J Maximum Reverse Recovery Time (Note 1) Typical Junction capacitance (Note 2) Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range SYMBOLS ER2A ER2B ER2C ER2D ER2E ER2G ER2J UNITS 50 100 150 200 300 400 600 Volts VRRM 35 70 105 140 210 280 420 Volts VRMS 50 100 150 200 300 400 600 Volts VDC I(AV) 2.0 Amps IFSM 50.0 Amps VF IR TRR CJ R £KJL TJ ,TSTG NOTES: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A 2. Measured at 1 MHz and Applied reverse voltage of 4.0 volts 2 3. 8.0mm (.013mm thick) land areas 0.95 1.25 5.0 150 35.0 25.0 20.0 -50 to +150 1.7 Volts £g A nS PF ¢J /W ¢J RATING AND CHARACTERISTIC CURVES ER2A THRU ER2J AVERAGE FORWARD RECTIFIED CURRENT, AMPERES trr +0.5A 0 -0.25 NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. -1.0 SET TIME BASE FOR Source Impedance = 50 Ohms 1cm 2.4 2.0 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD P.C.B. MOUNTED ON 0.3×0.3"(8.0×8.0mm) COPPER PAD AREAS 1.6 1.2 0.8 0.4 0 0 20 1,000 10 TJ = 75¢J T J = 25¢J 1 0.1 20 40 60 80 100 120 100 120 140 160 50.0 ER2A 10.0 ER2E 1.0 ER2J 0.1 TJ = 25¢J PULSE WIDTH = 300£gs 2% DUTY CYCLE 0.01 0 80 Fig. 2-MAXIMUM AVERAGE FORWARD CURRENT RATING INSTANTANEOUS FORWARD CURRENT AMPERES INSTANTANEOUS REVERSE CURRENT, MICROAMPERES Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM T J = 100 ¢J 60 LEAD TEMPERATURE, ¢J 50 ns/cm 100 40 140 0.01 0.4 0.5 0.8 1.0 1.2 1.4 1.6 1.8 PERCENT OF RATED PEAK INVERSE VOLTAGE, VOLTS REVERSE VOLTAGE, VOLTS Fig. 4-TYPICAL FORWARD CHARACTERISTICS 60 60 50 CAPACITANCE, pF PEAK FORWARD SURGE CURRENT, AMPERES Fig. 3-TYPICAL REVERSE CHARACTERISTICS 8.3ms SINGLE HALF SINE WAVE JEDEC METHOD 40 30 20 10 50 40 30 TJ = 25 ¢J 20 f = 1.0MHz Vsig = 50mVp-p 10 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz Fig. 5-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT .1 .5 1 2 5 10 20 50 100 200 500 1000 REVERSE VOLTAGE, VOLTS Fig. 6-TYPICAL JUNCTION CAPACITANCE