FR1A THRU FR1K SURFACE MOUNT FAST SWITCHING RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 1.0 Ampere FEATURES l For surface mounted applications l Low profile package l l Built-in strain relief Easy pick and place l l Fast recovery times for high efficiency Plastic package has Underwriters Laboratory l Flammability Classification 94V-O Glass passivated junction l SMB/DO-214AA High temperature soldering: 260 ¢J /10 seconds at terminals MECHANICAL DATA Case: JEDEC DO-214AA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard packaging: 12mm tape (EIA-481) Weight: 0.003 ounce, 0.093 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Resistive or inductive load. For capacitive load, derate current by 20%. Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at TL=90 ¢J Peak Forward Surge Current 8.3ms single half sinewave superimposed on rated load(JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current TA=25 ¢J At Rated DC Blocking Voltage TA=125 ¢J Maximum Reverse Recovery Time (Note 1) TJ =25 ¢J Typical Junction capacitance (Note 2) Maximum Thermal Resistance (Note 3) Operating and Storage Temperature Range SYMBOLS FR1A FR1B FR1D FR1G FR1J FR1K VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 UNITS Volts Volts Volts 1.0 Amps IFSM 30.0 Amps VF IR 1.3 5.0 150 Volts £g A TRR CJ R £KJL TJ ,TSTG NOTES: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A 2. Measured at 1 MHz and Applied reverse voltage of 4.0 volts 3. 8.0mm2 (.013mm thick) land areas 150 250 12 30 -50 to +150 500 nS PF ¢J /W ¢J RATING AND CHARACTERISTIC CURVES 1.6 1.4 CAPACITANCE, pF AVERAGE FORWARD RECTIFIED CURRENT AMPERES FR1A THRU FR1K SINGLE PHASE HALF WAVE RESISTIVE OR INDUCTIVE P.C.B MOUNTED ON 0.315×0.315"(8.0×8.0mm) PAD AREAS 1.2 1.0 .8 .6 .4 .2 0 20 40 60 80 100 120 140 160 TJ = 25 ¢J 10 1 180 1 10 LEAD TEMPERATURE, ¢J REVERSE VOLTAGE, Vdc 30 25 8.3ms SINGLE HALF SINE WAVE JEDEC METHOD 15 10 5 1 2 5 10 20 50 100 Fig. 2-TYPICAL JUNCTION CAPACITANCE INSTANTANEOUS FORWARD CURRENT, AMPERES PEAK FORWARD SURGE CURRENT, AMPERES Fig. 1-FORWARD CURRENT DERATING CURVE 20 100 10 PULSE WIDTH = 300£gs 1%DUTY CYCLE 1 TJ = 25 ¢J 0.1 0.01 0.2 NUMBER OF CYCLES AT 60Hz Fig. 3-PEAK FORWARD SURGE CURRENT 0.4 0.6 0.8 1.0 1.2 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 4-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS trr +0.5A 0 -0.25 NOTE:1.Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF 2.Rise Time = 10ns max. Source Impedance = 50 Ohms 1.6 -1.0 SET TIME BASE FOR 50 ns/cm 1cm Fig. 5-REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM