AD AD8218

Zero Drift, Bidirectional
Current Shunt Monitor
AD8218
High common-mode voltage range
4 V to 80 V operating
−0.3 V to 85 V survival
Buffered output voltage
Gain = 20 V/V
Wide operating temperature range: −40°C to +125°C
Excellent ac and dc performance
±100 nV/°C typical offset drift
±50 µV typical offset
±5 ppm/°C typical gain drift
110 dB typical CMRR at dc
FUNCTIONAL BLOCK DIAGRAM
VS
R4
AD8218
–IN
R1
OUT
+IN
R2
LDO
R3
ENB
GND
REF
09592-001
FEATURES
Figure 1.
APPLICATIONS
High-side current sensing
48 V telecom
Power management
Base stations
Bidirectional motor control
Precision high voltage current sources
GENERAL DESCRIPTION
The AD8218 is a high voltage, high resolution current shunt
amplifier. It features a set gain of 20 V/V, with a maximum
±0.35% gain error over the entire temperature range. The
buffered output voltage directly interfaces with any typical
converter. The AD8218 offers excellent input common-mode
rejection from 4 V to 80 V. The AD8218 performs bidirectional
current measurements across a shunt resistor in a variety of
industrial and telecom applications, including motor control,
battery management, and base station power amplifier bias
control.
The AD8218 offers breakthrough performance throughout the
−40°C to +125°C temperature range. It features a zero-drift core,
which leads to a typical offset drift of ±100 nV/°C throughout
the operating temperature range and the common-mode voltage
range. Special attention is devoted to output linearity being
maintained throughout the input differential voltage range of
0 mV to ~250 mV. The AD8218 also includes an internal 80 mV
reference that can be enabled for optimal dynamic range in
unidirectional current sense applications. The typical input
offset voltage is ±50 µV.
The AD8218 is offered in an 8-lead MSOP package.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2011 Analog Devices, Inc. All rights reserved.
AD8218
TABLE OF CONTENTS
Features .............................................................................................. 1
Output Clamping ....................................................................... 10
Applications ....................................................................................... 1
Application Notes ........................................................................... 11
Functional Block Diagram .............................................................. 1
Supply (VS) Connections ........................................................... 11
General Description ......................................................................... 1
Enable Pin (ENB) Operation .................................................... 11
Revision History ............................................................................... 2
Applications Information .............................................................. 12
Specifications..................................................................................... 3
Unidirectional High-Side Current Sensing ............................ 12
Absolute Maximum Ratings............................................................ 4
Bidirectional High-Side Current Sensing ............................... 12
ESD Caution .................................................................................. 4
Motor Control Current Sensing ............................................... 12
Pin Configuration and Function Descriptions ............................. 5
Outline Dimensions ....................................................................... 13
Typical Performance Characteristics ............................................. 6
Ordering Guide .......................................................................... 13
Theory of Operation ...................................................................... 10
Amplifier Core ............................................................................ 10
REVISION HISTORY
2/11—Rev. 0 to Rev. A
Changes to Features.......................................................................... 1
1/11—Revision 0: Initial Version
Rev. A | Page 2 of 16
AD8218
SPECIFICATIONS
TOPR = −40°C to +125°C, TA = 25°C, RL = 25 kΩ (RL is the output load resistor), input common-mode voltage (VCM) = 4 V, unless
otherwise noted.
Table 1.
Parameter
GAIN
Initial
Accuracy
Accuracy over Temperature
Gain vs. Temperature
VOLTAGE OFFSET
Offset Voltage (RTI 1)
Over Temperature (RTI1)
Offset Drift
INPUT
Bias Current2
Common-Mode Input Voltage Range
Differential Input Voltage Range3
Common-Mode Rejection (CMRR)
OUTPUT
Output Voltage Range Low
Output Voltage Range High
Output Impedance
INTERNAL REFERENCE (ENB PIN CONNECTED TO GND)
Initial Value
Offset (RTI1)
Offset Drift (RTO4)
REFERENCE INPUT (REF, PIN 7)
Input Impedance
Input Current
Input Voltage Range
Input-to-Output Gain
DYNAMIC RESPONSE
Small-Signal −3 dB Bandwidth
Slew Rate
NOISE
0.1 Hz to 10 Hz (RTI1)
Spectral Density, 1 kHz (RTI1)
POWER SUPPLY
Operating Range (Pin 2 Floating)
VS Range (Pin 2)
Quiescent Current over Temperature
Power Supply Rejection Ratio (PSRR)
TEMPERATURE RANGE
For Specified Performance
Min
Typ
Max
Unit
Test Conditions/Comments
V/V
%
%
ppm/°C
VO ≥ 0.1 V dc, TA
TOPR
TOPR
µV
µV
nV/°C
25°C
TOPR
TOPR
220
80
250
µA
µA
V
mV
dB
TA, input common mode = 4 V, VS = 4 V
TOPR, input common mode = 4 V, VS = 4 V
Common-mode continuous
Differential input voltage
TOPR
VS − 0.1
TA
2
V
V
Ω
80
mV
Voltage at OUT with a differential input of
0 V and a common-mode input of 4 V
20
±0.1
±0.35
±5
±200
±300
±100
130
4
0
90
110
0.01
−150
+150
±10
1.5
µV
µV/°C
1 ± 0.0001
MΩ
µA
V
V/V
450
1
kHz
V/µs
2.3
110
µV p-p
nV/√Hz
3
0
60
5
VS = NC or VS = 5 V
Dependent on VREF/1.5 MΩ
ENB not connected to GND
4
80
V
Power regulated from common mode,
VS pin floating
4
5.5
V
VS must be less than 5.5 V if standalone
supply is used
800
µA
dB
Throughout input common mode
TOPR
+125
°C
90
110
−40
RTI = referred to input.
Refer to Figure 8 for more information on the input bias current. This current varies based on the input common-mode voltage. The input bias current flowing to the
+IN pin is also the supply current to the internal LDO.
3
The differential input voltage is specified as 250 mV because the output is internally clamped to 5.2 V. This ensures that the output voltage does not exceed the typical
ADC input range, preventing damage. The AD8218 can survive up to ±5 V differentially but will only amplify ~250 mV correctly due to the output clamping function.
4
RTO = referred to output.
1
2
Rev. A | Page 3 of 16
AD8218
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Maximum Input Voltage ( +IN, −IN to GND)
Differential Input Voltage (+IN to –IN)
Human Body Model (HBM) ESD Rating
Operating Temperature Range (TOPR)
Storage Temperature Range
Output Short-Circuit Duration
Rating
−0.3 V to 85 V
±5 V
±2000 V
−40°C to +125°C
−65°C to +150°C
Indefinite
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Rev. A | Page 4 of 16
AD8218
+IN 1
VS 2
ENB 3
GND 4
AD8218
TOP VIEW
(Not to Scale)
8
–IN
7
REF
6
NC
5
OUT
NC = NO CONNECT.
DO NOT CONNECT TO THIS PIN.
09592-002
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
Mnemonic
+IN
VS
ENB
GND
OUT
NC
REF
−IN
Description
Noninverting Input.
Supply Pin. Bypass with a standard 0.1 μF capacitor.
Connect to GND to enable the internal 80 mV reference.
Ground.
Output.
Do not connect to this pin.
Reference Input. Connect to a low impedance voltage.
Inverting Input.
Rev. A | Page 5 of 16
AD8218
TYPICAL PERFORMANCE CHARACTERISTICS
30
40
27
38
24
36
MAGNITUDE (dB)
21
VOSI (µV)
34
32
30
18
15
12
9
28
6
26
0
20
40
60
80
100
120
140
TEMPERATURE (°C)
0
1k
Figure 3. Typical Input Offset vs. Temperature
10k
100k
FREQUENCY (Hz)
1M
09592-006
–20
09592-003
24
–40
3
Figure 6. Typical Small-Signal Bandwidth (VOUT = 200 mV p-p)
10
140
9
130
8
TOTAL OUTPUT ERROR (%)
120
CMRR (dB)
110
100
90
–40°C
+25°C
+125°C
80
70
7
6
5
4
3
2
1
0
–1
–2
–3
60
10k
100k
1M
FREQUENCY (Hz)
–5
09592-004
1000
0
Figure 4. Typical CMRR vs. Frequency
450
700
INPUT BIAS CURRENT (µA)
800
400
350
300
250
200
15
20
25
30
35
DIFFERENTIAL INPUT (mV)
40
45
50
+IN
600
500
400
300
200
100
150
–20
0
20
40
60
TEMPERATURE (°C)
80
100
120
0
5
10 15 20 25 30 35 40 45 50 55 60 65 70 75 80
INPUT COMMON-MODE VOLTAGE (V)
Figure 5. Typical Gain Error vs. Temperature
Figure 8. Input Bias Current vs. Input Common-Mode Voltage
(Differential Input Voltage = 5 mV, VS = NC)
Rev. A | Page 6 of 16
09592-008
–IN
0
09592-005
GAIN ERROR (ppm)
10
Figure 7. Total Output Error vs. Differential Input Voltage
500
100
–40
5
09592-007
–4
50
100
AD8218
500
INPUT
5mV/DIV
400
OUTPUT
350
100mV/DIV
300
0
20
40
60
80
100
120
TEMPERATURE (°C)
1µs/DIV
Figure 9. Supply Current vs. Temperature (VS = 5 V, VCM = 12 V)
09592-011
–20
Figure 12. Fall Time (Differential Input = 10 mV)
INPUT
100mV/DIV
INPUT
5mV/DIV
OUTPUT
2V/DIV
1µs/DIV
5µs/DIV
Figure 10. Rise Time (Differential Input = 10 mV)
09592-012
100mV/DIV
09592-009
OUTPUT
Figure 13. Fall Time (Differential Input = 200 mV)
INPUT
200mV/DIV
INPUT
100mV/DIV
OUTPUT
OUTPUT
2V/DIV
2V/DIV
5µs/DIV
5µs/DIV
Figure 11. Rise Time (Differential Input = 200 mV)
Figure 14. Differential Overload Recovery, Rising
Rev. A | Page 7 of 16
09592-013
200
–40
09592-109
250
09592-010
SUPPLY CURRENT (µA)
450
AD8218
9.5
MAXIMUM OUTPUT SOURCE CURRENT (mA)
INPUT
200mV/DIV
OUTPUT
09592-014
2V/DIV
8.5
8.0
7.5
7.0
6.5
6.0
5.5
5.0
4.5
150
TEMPERATURE (°C)
Figure 18. Maximum Output Source Current vs. Temperature
Figure 15. Differential Overload Recovery, Falling
5.010
81.0
80.5
80.0
79.5
0
20
40
60
80
TEMPERATURE (°C)
100
120
4.970
4.960
4.950
4.940
4.930
4.920
4.910
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
OUTPUT SOURCE CURRENT (mA)
Figure 19. Output Voltage Swing from Rail vs. Output Source Current
12.0
250
OUTPUT VOLTAGE RANGE FROM GND (V)
11.5
11.0
10.5
10.0
9.5
9.0
8.5
8.0
7.5
7.0
6.5
6.0
5.5
0
10 20 30 40 50 60 70 80 90 100 110 120
TEMPERATURE (°C)
200
150
100
50
0
09592-015
MAXIMUM OUTPUT SINK CURRENT (mA)
4.980
0
Figure 16. Internal Reference Voltage vs. Temperature
(VS = 5 V, VS = NC, VCM = 12 V, Pin 1 (+IN) and Pin 8 (−IN) Shorted, Pin 3 (ENB)
Shorted to Pin 4 (GND))
5.0
–40 –30 –20 –10
4.990
4.900
09592-116
–20
5.000
0
Figure 17. Maximum Output Sink Current vs. Temperature
0.5
1.0
1.5
2.0
2.5
3.0
3.5
OUTPUT SINK CURRENT (mA)
4.0
4.5
5.0
09592-018
REFERENCE RTO (mV)
81.5
09592-017
OUTPUT VOLTAGE SWING FROM RAIL (V)
82.0
79.0
–40
09592-016
140
130
110
120
90
100
80
70
60
50
40
30
20
0
10
–10
–20
–30
4.0
–40
5µs/DIV
9.0
Figure 20. Output Voltage Range from GND vs. Output Sink Current
Rev. A | Page 8 of 16
AD8218
500
INPUT
400
COUNT
50V/DIV
OUTPUT
300
200
1V/DIV
500ns/DIV
0
–4
09592-022
09592-019
100
–3
–2
–1
0
1
3
2
4
GAIN DRIFT (ppm/°C)
Figure 21. Common-Mode Step Response, Rising
Figure 24. Gain Drift Distribution
140
120
INPUT
50V/DIV
COUNT
100
OUTPUT
1V/DIV
80
60
40
1µs/DIV
0
–0.6
09592-023
09592-020
20
–0.4
–0.2
0
0.2
0.4
0.6
OFFSET DRIFT (µV/°C)
Figure 25. Input Offset Drift Distribution
Figure 22. Common-Mode Step Response, Falling
180
250
150
200
COUNT
90
150
100
60
0
–200
–100
0
100
09592-024
50
30
09592-021
COUNT
120
0
–5
200
0
5
10
INTERNAL REF OFFSET DRIFT (µV/°C)
VOSI (µV)
Figure 23. Input Offset Distribution
Figure 26. Internal REF Offset Drift Distribution,
Referred to Output (RTO)
Rev. A | Page 9 of 16
15
AD8218
THEORY OF OPERATION
The AD8218 is configured as a difference amplifier. The
transfer function is
AMPLIFIER CORE
In typical applications, the AD8218 amplifies a small differential
input voltage generated by the load current flowing through
a shunt resistor. The AD8218 rejects high common-mode voltages (up to 80 V) and provides a ground-referenced, buffered
output. Figure 27 shows a simplified schematic of the AD8218.
5V
ILOAD
VS
ICHARGE
Resistors R4 and R1 are matched to within 0.01% and have
values of 1.5 MΩ and 75 kΩ, respectively, meaning an inputto-output total gain of 20 V/V for the AD8218. The difference
between V1 and V2 is the voltage across the shunt resistor, or
VIN. Therefore, the input-to-output transfer function of the
AD8218 is
CF
GND
OUT (V) = (20 × VIN) + VREF
R4
AD8218
–IN
OUT = ((R4/R1) × (V1 − V2)) + VREF
The AD8218 accurately amplifies the input differential signal,
rejecting high voltage common modes ranging from 4 V to 80 V.
R1
V2
OUT
SHUNT +IN
V1
4V
TO
80V
R2
LDO
The main amplifier uses a novel zero-drift architecture, providing
the end user with breakthrough temperature stability. The
offset drift is typically less than ±100 nV/°C. This performance
leads to optimal accuracy and dynamic range.
R3
ENB
REF
GND
VREF
Figure 27. Simplified Schematic
09592-027
LOAD
OUTPUT CLAMPING
After the input common-mode voltage in the application is
above 5.2 V, the internal LDO output of the AD8218 also
reaches its maximum value of 5.2 V, which is the maximum
output range of the AD8218. Because in typical applications
the output interfaces with a converter, clamping the AD8218
output voltage to 5.2 V ensures that the ADC input is not
damaged due to excessive overvoltage.
Rev. A | Page 10 of 16
AD8218
APPLICATION NOTES
SUPPLY (VS) CONNECTIONS
ENABLE PIN (ENB) OPERATION
The AD8218 includes an internal LDO, which allows the user
to leave the VS pin floating, powering the AD8218 directly from
the voltage present at Pin 1 (+IN), provided this voltage is in the
4 V to 80 V range. A typical connection for the part in this
configuration is shown in Figure 28.
The AD8218 includes an internal reference that can be enabled
by connecting Pin 3 (ENB) to ground. This mode of operation
is shown in Figure 30.
ILOAD
ICHARGE
4V
TO
80V
SHUNT
BATTERY
LOAD
+IN
–IN
VS
REF
AD8218
VS
REF
OUT
GND
09592-028
Figure 30. Enabling the Internal 80 mV Reference
The AD8218 can also be powered from a separate low impedance
supply at Pin 2 (VS); however, this voltage can only be in the 4 V
to 5.5 V range. In cases where the high voltage bus is susceptible
to noise, transients, or high voltage fluctuations and a 5 V supply is
available, the AD8218 can be used in the mode depicted in
Figure 29.
ICHARGE
ILOAD
5V
–IN
ENB
2.5V
Figure 28. Operation with No VS Connection
SHUNT
LOAD
+IN
–IN
VS
REF
AD8218
OUT (V) = OUT (V) = (20 × VIN) + 0.08 V
If Pin 3 is connected to ground, and therefore the internal
reference is enabled, 80 mV must always be added to the
transfer function of the AD8218.
2.5V
OUT
ENB
In this configuration, the internal 80 mV reference is activated,
and the output of the AD8218 is 80 mV when the differential
input voltage is 0 V and the voltage at Pin 7 (REF) is also 0 V. This
internal reference is useful in unidirectional current measurements
where the current being monitored has a very wide range. Setting
the output starting point to 80 mV means that when the load
current through the shunt resistor is 0 A, the output is 80 mV.
This ensures that the output errors due to initial offset and the
output saturation range of the amplifier are overcome. In this
mode, the transfer function of the AD8218 becomes
GND
09592-029
CF
LOAD
+IN
AD8218
GND
4V
TO
80V
SHUNT
OUT
ENB
BATTERY
4V
TO
80V
09592-030
BATTERY
ILOAD
Figure 29. 5 V Supply Operation
Rev. A | Page 11 of 16
AD8218
APPLICATIONS INFORMATION
UNIDIRECTIONAL HIGH-SIDE CURRENT SENSING
VS
ILOAD
In the unidirectional high-side current sensing configuration,
the shunt resistor is referenced to the battery (see Figure 31).
High voltage is present at the inputs of the current sense amplifier.
When the shunt is battery referenced, the AD8218 produces a
linear ground-referenced analog output. The supply pin, VS, of the
AD8218 can either be connected to a 5 V supply or left floating (see
the Supply (VS) Connections section).
AD8218
R1
–IN
V2
OUT
SHUNT +IN
LOAD
V1
R2
BATTERY
(4V TO 80V)
ENB
09592-033
Figure 33. Bidirectional Operation Using a 2.5 V Reference Input
R1
V2
OUT
SHUNT +IN
LOAD
V1
R2
BATTERY
(4V TO 80V)
ENB
GND
2.5V
R4
AD8218
–IN
R3
LDO
REF
VS
ILOAD
R4
LDO
R3
The output transfer function curve for bidirectional operation
using a 2.5 V reference input is shown in Figure 34.
5.0
4.5
Figure 31. Unidirectional Operation with ENB Connected to GND
The output transfer function curve for unidirectional operation
with ENB connected to GND is shown in Figure 32.
3.5
3.0
2.5
2.0
1.5
280
1.0
240
0.5
0
–0.15
200
–0.10
–0.05
0
0.05
0.10
0.15
INPUT VOLTAGE (V)
160
Figure 34. Transfer Function When Using a 2.5 V Reference Input
120
MOTOR CONTROL CURRENT SENSING
80
0
0
1
2
3
4
5
6
7
8
9
10
INPUT VOLTAGE (mV)
09592-032
40
Figure 32. Output Transfer Function with ENB Connected to GND
The AD8218 is a practical, accurate solution for high-side
current sensing in motor control applications. In cases where
the shunt resistor is referenced to a battery and the current
flowing is bidirectional (as shown in Figure 35), the AD8218
monitors the current with no additional supply pin necessary.
BATTERY
BIDIRECTIONAL HIGH-SIDE CURRENT SENSING
IMOTOR
Inputting a voltage at Pin 7 (REF) offsets the output of the AD8218
and allows for bidirectional current sensing. The transfer function
from the REF pin to the output is 1 V/V. For example, a 2.5 V REF
input offsets the output of the AD8218 to 2.5 V. See Figure 33
for typical connections. The user must ensure that the voltage
applied at Pin 7 (REF) is from a low impedance source.
+IN
–IN
VS
REF
AD8218
MOTOR
VREF
OUT
ENB
GND
09592-035
OUTPUT VOLTAGE (mV)
320
4.0
09592-034
09592-031
GND
OUTPUT VOLTAGE (V)
REF
Figure 35. High-Side Current Sensing in Motor Control
Rev. A | Page 12 of 16
AD8218
OUTLINE DIMENSIONS
3.20
3.00
2.80
8
3.20
3.00
2.80
1
5.15
4.90
4.65
5
4
PIN 1
IDENTIFIER
0.65 BSC
0.95
0.85
0.75
15° MAX
1.10 MAX
0.40
0.25
6°
0°
0.23
0.09
0.80
0.55
0.40
COMPLIANT TO JEDEC STANDARDS MO-187-AA
10-07-2009-B
0.15
0.05
COPLANARITY
0.10
Figure 36. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD8218BRMZ
AD8218BRMZ-RL
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
Package Description
8-Lead Mini Small Outline Package [MSOP]
8-Lead Mini Small Outline Package [MSOP]
Z = RoHS Compliant Part.
Rev. A | Page 13 of 16
Package Option
RM-8
RM-8
Branding
Y3K
Y3K
AD8218
NOTES
Rev. A | Page 14 of 16
AD8218
NOTES
Rev. A | Page 15 of 16
AD8218
NOTES
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09592-0-2/11(A)
Rev. A | Page 16 of 16