A1301 and A1302 Continuous-Time Ratiometric Linear Hall Effect Sensor ICs Features and Benefits Description ▪ ▪ ▪ ▪ ▪ ▪ The A1301 and A1302 are continuous-time, ratiometric, linear Hall-effect sensor ICs. They are optimized to accurately provide a voltage output that is proportional to an applied magnetic field. These devices have a quiescent output voltage that is 50% of the supply voltage. Two output sensitivity options are provided: 2.5 mV/G typical for the A1301, and 1.3 mV/G typical for the A1302. Low-noise output Fast power-on time Ratiometric rail-to-rail output 4.5 to 6.0 V operation Solid-state reliability Factory-programmed at end-of-line for optimum performance ▪ Robust ESD performance The Hall-effect integrated circuit included in each device includes a Hall circuit, a linear amplifier, and a CMOS Class A output structure. Integrating the Hall circuit and the amplifier on a single chip minimizes many of the problems normally associated with low voltage level analog signals. Packages: 3 pin SOT23W (suffix LH), and 3 pin SIP (suffix UA) High precision in output levels is obtained by internal gain and offset trim adjustments made at end-of-line during the manufacturing process. These features make the A1301 and A1302 ideal for use in position sensing systems, for both linear target motion and rotational target motion. They are well-suited for industrial applications over extended temperature ranges, from –40°C to 125°C. Two device package types are available: LH, a 3-pin SOT23W type for surface mount, and UA, a 3-pin ultramini SIP for through-hole mount. They are lead (Pb) free (suffix, –T) with 100% matte tin plated leadframes. Not to scale Functional Block Diagram V+ To all subcircuits Amp Gain Filter VCC Out Offset CBYPASS Trim Control GND A1301-DS, Rev. 17 VOUT Continuous-Time Ratiometric Linear Hall Effect Sensor ICs A1301 and A1302 Selection Guide Part Number Packing* Package Ambient, TA SIP –40ºC to 85ºC A1301EUA-T Bulk, 500 pieces/bag A1301KLHLT-T 7-in. tape and reel, 3000 pieces/reel A1301KUA-T Bulk, 500 pieces/bag A1302ELHLT-T 7-in. tape and reel, 3000 pieces/reel Surface Mount A1302KLHLT-T 7-in. tape and reel, 3000 pieces/reel Surface Mount A1302KUA-T Bulk, 500 pieces/bag Surface Mount SIP SIP Sensitivity (Typical) 2.5 mV/G –40ºC to 125ºC –40ºC to 85ºC 1.3 mV/G –40ºC to 125ºC *Contact Allegro for additional packing options. Absolute Maximum Ratings Characteristic Symbol Notes Rating Units Supply Voltage VCC 8 V Output Voltage VOUT 8 V Reverse Supply Voltage VRCC –0.1 V Reverse Output Voltage VROUT –0.1 V Output Sink Current IOUT 10 mA Range E –40 to 85 ºC Range K Operating Ambient Temperature TA –40 to 125 ºC Maximum Junction Temperature TJ(max) 165 ºC Tstg –65 to 170 ºC Storage Temperature Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 2 Continuous-Time Ratiometric Linear Hall Effect Sensor ICs A1301 and A1302 Pin-out Drawings Package UA Package LH 3 1 2 1 2 3 Terminal List Symbol VCC VOUT GND Number Package LH Package UA 1 1 2 3 3 2 Description Connects power supply to chip Output from circuit Ground Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 3 A1301 and A1302 Continuous-Time Ratiometric Linear Hall Effect Sensor ICs DEVICE CHARACTERISTICS over operating temperature range, TA, and VCC = 5 V, unless otherwise noted Characteristic Symbol Test Conditions Min. Electrical Characteristics Running, TJ < 165°C 4.5 Supply Voltage VCC Supply Current ICC Output open – VOUT(High) ISOURCE = –1 mA, Sens = nominal 4.65 Output Voltage – VOUT(Low) ISINK = 1 mA, Sens = nominal Output Bandwidth BW – VCC(min) to 0.95 VOUT; B = ±1400 G; Power-On Time tPO – Slew rate = 4.5 V/μs to 4.5 V/100 ns Output Resistance ROUT ISINK ≤ 1 mA, ISOURCE ≥ –1 mA – External output low pass filter ≤ 10 kHz; Wide Band Output Noise, rms VOUTN – Sens = nominal Ratiometry Quiescent Output Voltage Error ΔVOUTQ(V) TA = 25°C – with respect to ∆VCC1 Magnetic Sensitivity Error with ΔSens(V) TA = 25°C – respect to ∆VCC2 Output Linearity Lin TA = 25°C – – Symmetry Sym TA = 25°C Magnetic Characteristics Quiescent Output Voltage VOUTQ B = 0 G; TA = 25°C 2.4 Quiescent Output Voltage over VOUTQ(TA) B = 0 G 2.2 Operating Temperature Range A1301; TA = 25°C 2.0 Magnetic Sensitivity Sens A1302; TA = 25°C 1.0 A1301 1.8 Magnetic Sensitivity over Sens(TA) Operating Temperature Range A1302 0.85 1Refer to equation (4) in Ratiometric section on page 4. 2Refer to equation (5) in Ratiometric section on page 4. Typ. Max. Units – – 4.7 0.2 20 6 11 – 0.25 – V mA V V kHz 3 5 μs 2 5 Ω 150 – μV – ±3.0 % – ±3.0 % – – ±2.5 ±3.0 % % 2.5 2.6 V – 2.8 V 2.5 1.3 – – 3.0 1.6 3.2 1.75 mV/G mV/G mV/G mV/G Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 4 Continuous-Time Ratiometric Linear Hall Effect Sensor ICs A1301 and A1302 Characteristic Definitions Quiescent Output Voltage. In the quiescent state (no significant magnetic field: B = 0), the output, VOUTQ, equals one half of the supply voltage, VCC, throughout the entire operating ranges of VCC and ambient temperature, TA. Due to internal component tolerances and thermal considerations, there is a tolerance on the quiescent output voltage, ∆VOUTQ, which is a function of both ∆VCC and ∆TA. For purposes of specification, the quiescent output voltage as a function of temperature, ∆VOUTQ(∆TA), is defined as: ΔVOUTQ(ΔΤΑ) = VOUTQ(ΤΑ) – VOUTQ(25ºC) Sensitivity. The presence of a south-polarity (+B) magnetic field, perpendicular to the branded face of the device package, increases the output voltage, VOUT, in proportion to the magnetic field applied, from VOUTQ toward the VCC rail. Conversely, the application of a north polarity (–B) magnetic field, in the same orientation, proportionally decreases the output voltage from its quiescent value. This proportionality is specified as the magnetic sensitivity of the device and is defined as: 2B Sens(ΤΑ) – Sens(25ºC) Sens(25ºC) ΔSens(ΔV) = Lin+ = Lin– = × 100% VOUTQ(VCC) VCC VOUTQ(5V) × 100% 5V (4) (3) Sens(VCC) VCC Sens(5V) 5V × 100% (5) Linearity and Symmetry. The on-chip output stage is designed to provide linear output at a supply voltage of 5 V. Although the application of very high magnetic fields does not damage these devices, it does force their output into a nonlinear region. Linearity in percent is measured and defined as: (2) The stability of the device magnetic sensitivity as a function of ambient temperature, ∆ Sens (∆TA) (%) is defined as: ΔSens(ΔΤΑ) = ΔVOUTQ(ΔV) = and the ratiometric change (%) in sensitivity is defined as: Sens(25ºC) VOUT(–B) – VOUT(+B) The ratiometric change (%) in the quiescent voltage output is defined as: (1) where Sens is in mV/G, and the result is the device equivalent accuracy, in gauss (G), applicable over the entire operating temperature range. Sens = Ratiometric. The A1301 and A1302 feature a ratiometric output. This means that the quiescent voltage output, VOUTQ, and the magnetic sensitivity, Sens, are proportional to the supply voltage, VCC. VOUT(+B) – VOUTQ 2 (VOUT(+B½) – VVOUTQ ) VOUT(–B) – VOUTQ 2(VOUT(–B½) – VOUTQ) × 100% × 100% (6) (7) and output symmetry as: Sym = VOUT(+B) – VOUTQ VOUTQ – VOUT(–B) × 100% Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com (8) 5 Continuous-Time Ratiometric Linear Hall Effect Sensor ICs A1301 and A1302 Typical Characteristics (30 pieces, 3 fabrication lots) 1301 Device Sensitivity vs. Ambient Temperature 1302 Device Sensitivity vs. Temperature 1.40 2.65 1.38 UA Package Sensitivity (mV/G) Sensitivity (mV/G) 2.60 2.55 2.50 LH Package 2.45 2.40 UA Package 1.36 1.34 1.32 1.30 LH Package 1.28 1.26 2.35 –50 –25 1.24 0 25 50 75 Temperature (°C) 100 125 150 -50 1301 Device VOUTQ vs. Ambient Temperature 25 50 75 100 125 150 Temperature (°C) 2.60 Output Voltage (V) Output Voltage (V) 0 1302 Device VOUTQ vs. Ambient Temperature 2.60 2.55 2.50 2.45 2.40 –50 -25 –25 0 25 50 75 100 Temperature (°C) 125 2.55 2.50 2.45 2.40 –50 150 1301 Device Sensitivity vs. Supply Voltage –25 0 25 50 75 100 Temperature (°C) 125 150 1302 Device Sensitivity vs. Supply Voltage 1.7 3.5 Sensitivity (mV/G) Sensitivity (mV/G) 1.6 3.0 2.5 2.0 1.5 1.4 1.3 1.2 1.1 1.5 4.5 5.0 5.5 Supply Voltage (V) 6.0 1.0 4.5 5.0 5.5 Supply Voltage (V) 6.0 Continued on the next page... Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 6 Continuous-Time Ratiometric Linear Hall Effect Sensor ICs A1301 and A1302 Typical Characteristics, continued (30 pieces, 3 fabrication lots) 1302 Device VOUTQ vs. Supply Voltage 1301 Device VOUTQ vs. Supply Voltage 3.5 Output Voltage (V) Output Voltage (V) 3.5 3.0 2.5 2.0 1.5 4.5 5.0 5.5 Supply Voltage (V) 3.0 2.5 2.0 1.5 4.5 6.0 5.0 5.5 Supply Voltage (V) 1302 Device LIN+ and LIN– vs. Supply Voltage 1301 Device LIN+ and LIN– vs. Supply Voltage 100.4 100.0 100.3 99.9 LIN– Linearity (%) 100.2 Linearity (%) 6.0 100.1 100.0 LIN+ LIN+ 99.8 LIN– 99.7 99.9 99.8 4.5 5.0 5.5 Supply Voltage (V) 99.6 4.5 6.0 100.0 100.5 99.9 99.8 100.4 100.3 99.7 99.6 100.2 100.1 Symmetry (%) Symmetry (%) 6.0 1302 Device Symmetry vs. Supply Voltage 1301 Device Symmetry vs. Supply Voltage 99.5 99.4 99.3 99.2 99.1 99.0 4.5 5.0 5.5 Supply Voltage (V) 100.0 99.9 99.8 99.7 99.6 5.0 5.5 Supply Voltage (V) 6.0 99.5 4.5 5.0 5.5 Supply Voltage (V) 6.0 Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 7 Continuous-Time Ratiometric Linear Hall Effect Sensor ICs A1301 and A1302 Package LH, 3-Pin; (SOT-23W) +0.12 2.98 –0.08 1.49 D 4°±4° 3 A +0.020 0.180–0.053 0.96 D +0.10 2.90 –0.20 +0.19 1.91 –0.06 2.40 0.70 D 0.25 MIN 1.00 2 1 0.55 REF 0.25 BSC 0.95 Seating Plane Gauge Plane 8X 10° REF B PCB Layout Reference View Branded Face 1.00 ±0.13 +0.10 0.05 –0.05 0.95 BSC 0.40 ±0.10 For Reference Only; not for tooling use (reference dwg. 802840) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Active Area Depth, 0.28 mm REF B Reference land pattern layout All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances C Branding scale and appearance at supplier discretion D Hall element, not to scale NNT 1 C Standard Branding Reference View N = Last two digits of device part number T = Temperature code Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 8 Continuous-Time Ratiometric Linear Hall Effect Sensor ICs A1301 and A1302 Package UA, 3-Pin SIP Matrix Leadframe +0.08 4.09 –0.05 45° B C E 2.04 1.52 ±0.05 1.44 E +0.08 3.02 –0.05 Mold Ejector Pin Indent 2X10° E Branded Face 45° 1 D Standard Branding Reference View A 1.02 MAX 0.51 REF = Supplier emblem N = Last two digits of device part number T = Temperature code 0.79 REF 1 2 3 +0.03 0.41 –0.06 14.99 ±0.25 +0.05 0.43 –0.07 NNT For Reference Only; not for tooling use (reference DWG-9013) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Dambar removal protrusion (6X) B Gate and tie bar burr area C Active Area Depth, 0.50 mm REF D Branding scale and appearance at supplier discretion E Hall element, not to scale 1.27 NOM Please note that there are changes to the existing UA package drawing pending. Please contact the Allegro Marketing department for additional information. Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 9 Continuous-Time Ratiometric Linear Hall Effect Sensor ICs A1301 and A1302 Package UA, 3-Pin SIP Conventional Leadframe +0.08 4.09 –0.05 45° B C E 2.04 1.52 ±0.05 1.44 E Mold Ejector Pin Indent +0.08 3.02 –0.05 E Branded Face 45° 1 2.16 MAX D Standard Branding Reference View = Supplier emblem N = Last two digits of device part number T = Temperature code 0.79 REF A 0.51 REF NNT 1 2 3 +0.03 0.41 –0.06 15.75 ±0.51 For Reference Only; not for tooling use (reference DWG-9049) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Dambar removal protrusion (6X) B Gate burr area C Active Area Depth, 0.50 mm REF +0.05 0.43 –0.07 D Branding scale and appearance at supplier discretion E Hall element, not to scale 1.27 NOM Copyright ©2005-2010, Allegro MicroSystems, Inc. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro’s products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the failure of that life support device or system, or to affect the safety or effectiveness of that device or system. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. For the latest version of this document, visit our website: www.allegromicro.com Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 10