ALTERA EPCS128

3. Serial Configuration Devices (EPCS1,
EPCS4, EPCS16, EPCS64, and EPCS128)
Data Sheet
C51014-3.3
Features
The serial configuration devices provide the following features:
1
© December 2009
■
1-, 4-, 16-, 64-, and 128-Mbit flash memory devices that serially configure
Arria® series, Cyclone® series, all device families in the Stratix® series except the
Stratix device family, and FPGAs using the active serial (AS) configuration scheme
■
Easy-to-use four-pin interface
■
Low cost, low-pin count, and non-volatile memory
■
Low current during configuration and near-zero standby mode current
■
2.7-V to 3.6-V operation
■
EPCS1 and EPCS4 available in 8-pin small outline integrated circuit (SOIC)
package. EPCS16 available in 8-pin or 16-pin SOIC packages. EPCS64 and
EPCS128 available in 16-pin SOIC package
■
Enables the Nios® processor to access unused flash memory through AS memory
interface
■
Re-programmable memory with more than 100,000 erase/program cycles
■
Write protection support for memory sectors using status register bits
■
In-system programming support with SRunner software driver
■
In-system programming support with USB Blaster™, EthernetBlaster, or
ByteBlaster™ II download cables
■
Additional programming support with the Altera® Programming Unit (APU) and
programming hardware from BP Microsystems, System General, and other
vendors
■
Delivered with the memory array erased (all the bits set to 1)
The term “serial configuration devices” used in this document refers to Altera EPCS1,
EPCS4, EPCS16, EPCS64, and EPCS128.
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–2
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Functional Description
Functional Description
With SRAM-based devices that support active serial configuration, configuration data
must be reloaded each time the device powers up, the system reconfigures, or when
new configuration data is required. Serial configuration devices are flash memory
devices with a serial interface that can store configuration data for FPGA devices that
support active serial configuration and reload the data to the device upon power-up
or reconfiguration. Table 3–1 summarizes the features of the Altera configuration
devices and the amount of configuration space they hold.
Table 3–1. Altera Configuration Devices (Note 1), (2)
Device
EPCS1
Memory Size
(bits)
On-Chip
Decompression
Support
ISP
Support
Cascading
Support
Reprogrammable
Operating
Voltage (V)
1,048,576
No
Yes
No
Yes
3.3
EPCS4
4,194,304
No
Yes
No
Yes
3.3
EPCS16
16,777,216
No
Yes
No
Yes
3.3
EPCS64
67,108,864
No
Yes
No
Yes
3.3
EPCS128
134,217,728
No
Yes
No
Yes
3.3
Notes to Table 3–1:
(1) To program these devices using Altera Programming Unit or Master Programming Unit, refer to Altera Programming Hardware Data Sheet.
(2) The EPCS device can be re-programmed in system with Byte Blaster II download cable or an external microprocessor using SRunner. For more
information about SRunner, refer to the AN418, SRunner: An Embedded Solution for EPCS Programming.
For an 8-pin SOIC package, you can migrate vertically from the EPCS1 to the EPCS4
or EPCS16 because the EPCS devices are offered in the same device package.
Similarly, for a 16-pin SOIC package, you can migrate vertically from the EPCS16 to
the EPCS64 or EPCS128.
Use the compression ratio calculation to determine the FPGA device to fit the EPCS.
Example 3–1. Compression Ratio Calculation
EP4SGX530 = 189,000,000 bits
EPCS128 = 134,217,728 bits
Preliminary data indicates that compression typically reduces the configuration
bitstream size by 35% to 55%. We take the worst case that is 35% compression.
189,000,000 bits × 0.65 = 122,850,000 bits
It fits EPCS128 device.
With the new data-decompression feature in Arria series, Cyclone series, and all
device families in the Stratix series except the Stratix device family, you can use
smaller serial configuration devices to configure larger FPGAs.
1
f
Serial configuration devices cannot be cascaded.
For more information about the FPGA decompression feature, refer to the
configuration chapter in the appropriate device handbook.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Active Serial FPGA Configuration
3–3
The serial configuration devices are designed to configure the Cyclone series and all
device families in the Stratix series except the Stratix device family. It cannot configure
other existing Altera FPGA device families.
Figure 3–1 shows the serial configuration device block diagram.
Figure 3–1. Serial Configuration Device Block Diagram
Serial Configuration Device
nCS
Control
Logic
DCLK
DATA
I/O Shift
Register
Address Counter
Data Buffer
Decode Logic
Memory
Array
ASDI
Status Register
Accessing Memory in Serial Configuration Devices
You can access the unused memory locations of the serial configuration device to store
or retrieve data through the Nios processor and SOPC Builder. SOPC Builder is an
Altera tool for creating bus-based (especially microprocessor-based) systems in Altera
devices. SOPC Builder assembles library components such as processors and
memories into custom microprocessor systems.
SOPC Builder includes the EPCS device controller core, which is an interface core
specifically designed to work with the serial configuration device. With this core, you
can create a system with a Nios embedded processor that allows software access to
any memory location within the serial configuration device.
f
For more information about accessing memory within the serial configuration device,
refer to the Active Serial Memory Interface Data Sheet.
Active Serial FPGA Configuration
The following Altera FPGAs support Active Serial (AS) configuration scheme with
serial configuration devices:
1
© December 2009
■
Arria series
■
Cyclone series
■
all device families in the Stratix series except the Stratix device family
This section is only relevant for FPGAs that support the AS configuration scheme.
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–4
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Active Serial FPGA Configuration
There are four signals on the serial configuration device that interface directly with
the FPGA’s control signals. The serial configuration device signals DATA, DCLK, ASDI,
and nCS interface with DATA0, DCLK, ASDO, and nCSO control signals on the FPGA,
respectively. Figure 3–2 shows a serial configuration device programmed via a
download cable, which configures an FPGA in AS mode. Figure 3–3 shows a serial
configuration device programmed using the APU or a third-party programmer
configuring an FPGA in AS configuration mode.
f
For more information about the serial configuration device pin description, refer to
Table 3–23.
Figure 3–2. Altera FPGA Configuration in AS Mode (Serial Configuration Device Programmed Using Download Cable)
(Note 1) , (4)
VCC (1)
10 k
VCC (1) VCC (1)
10 k
10 k
Altera FPGA
CONF_DONE
nSTATUS
Serial
Configuration
Device (2)
nCEO
N.C.
nCONFIG
nCE
MSEL[]
(3)
10 k
DATA
DATA0
DCLK
DCLK
nCS
nCSO
ASDI
ASDO
Pin 1
VCC (1)
Notes to Figure 3–2:
(1) For the VCC value, refer to the respective FPGA family handbook Configuration chapter.
(2) Serial configuration devices cannot be cascaded.
(3) Connect the FPGA MSEL[] input pins to select the AS configuration mode. For details, refer to the respective FPGA family chapter in the
Configuration Handbook.
(4) For more information about configuration pin I/O requirements in an AS scheme for an Altera FPGA, refer to the respective FPGA family handbook
Configuration chapter.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Active Serial FPGA Configuration
3–5
Figure 3–3. Altera FPGA Configuration in AS Mode (Serial Configuration Device Programmed by APU or Third-Party
Programmer) (Note 1), (4)
VCC (1)
10 k
VCC (1) VCC (1)
10 k
10 k
Altera FPGA
CONF_DONE
nSTATUS
Serial
Configuration
Device (2)
nCEO
N.C.
nCONFIG
nCE
DATA
DATA0
DCLK
DCLK
nCS
nCSO
ASDI
ASDO
MSEL[]
(3)
Notes to Figure 3–3:
(1) For the VCC value, refer to the respective FPGA family handbook Configuration chapter.
(2) Serial configuration devices cannot be cascaded.
(3) Connect the FPGA MSEL[] input pins to select the AS configuration mode. For details, refer to the respective FPGA family chapter in the
Configuration Handbook.
(4) For more information about configuration pin I/O requirements in an AS scheme for an Altera FPGA, refer to the respective FPGA family handbook
Configuration chapter..
The FPGA acts as the configuration master in the configuration flow and provides the
clock to the serial configuration device. The FPGA enables the serial configuration
device by pulling the nCS signal low via the nCSO signal (refer to Figure 3–2 and
Figure 3–3). Subsequently, the FPGA sends the instructions and addresses to the serial
configuration device via the ASDO signal. The serial configuration device responds to
the instructions by sending the configuration data to the FPGA’s DATA0 pin on the
falling edge of DCLK. The data is latched into the FPGA on the next DCLK signal’s
falling edge.
1
Before the FPGA enters configuration mode, ensure that VCC of the EPCS is ready. If it
is not, you must hold nCONFIG low until all power rails of EPCS are ready.
The FPGA controls the nSTATUS and CONF_DONE pins during configuration in AS
mode. If the CONF_DONE signal does not go high at the end of configuration or if the
signal goes high too early, the FPGA will pulse its nSTATUS pin low to start
reconfiguration. Upon successful configuration, the FPGA releases the CONF_DONE
pin, allowing the external 10-k resistor to pull this signal high. Initialization begins
after the CONF_DONE goes high. After initialization, the FPGA enters user mode.
f
© December 2009
For more information about configuring the FPGAs in AS mode or other
configuration modes, refer to the Configuration chapter in the appropriate device
handbook.
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–6
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Active Serial FPGA Configuration
Multiple devices can be configured by a single EPCS device. However, serial
configuration devices cannot be cascaded. Refer to Table 3–1 to ensure the
programming file size of the cascaded FPGAs does not exceed the capacity of a serial
configuration device. Figure 3–4 shows the AS configuration scheme with multiple
FPGAs in the chain. The first FPGA is the configuration master and has its MSEL[]
pins set to AS mode. The following FPGAs are configuration slave devices and have
their MSEL[] pins set to PS mode.
Figure 3–4. Multiple Devices in AS Mode (Note 1), (5)
VCC (1)
10 k
VCC (1)
10 k
VCC (1)
10 k
Altera FPGA (Master)
Serial
Configuration
Device (2)
Altera FPGA (Slave)
CONF_DONE
CONF_DONE
nSTATUS
nSTATUS
nCONFIG
nCONFIG
nCE
nCEO
MSEL[]
nCE
(3)
nCEO
MSEL[ ]
DATA
DATA0
DATA0
DCLK
DCLK
DCLK
nCS
nCSO
ASDI
ASDO
N.C.
(4)
Notes to Figure 3–4:
(1) For the VCC value, refer to the respective FPGA family handbook Configuration chapter.
(2) Serial configuration devices cannot be cascaded.
(3) Connect the FPGA MSEL[] input pins to select the AS configuration mode. For details, refer to the appropriate FPGA family chapter in the
Configuration Handbook.
(4) Connect the FPGA MSEL[] input pins to select the PS configuration mode. For details, refer to the appropriate FPGA family chapter in the
Configuration Handbook.
(5) For more information about configuration pin I/O requirements in an AS scheme for an Altera FPGA, refer to the respective FPGA family handbook
Configuration chapter.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–7
Serial Configuration Device Memory Access
This section describes the serial configuration device’s memory array organization
and operation codes. Timing specifications for the memory are provided in the
“Timing Information” section.
Memory Array Organization
Table 3–2 provides details about the memory array organization in EPCS128, EPCS64,
EPCS16, EPCS4, and EPCS1.
Table 3–2. Memory Array Organization in Serial Configuration Devices
Details
Bytes (bits)
Number of sectors
Bytes (bits) per
sector
EPCS128
EPCS64
EPCS16
EPCS4
EPCS1
16,777,216 bytes
(128 Mbits)
8,388,608 bytes
(64 Mbits)
2,097,152 bytes
(16 Mbits)
524,288 bytes
(4 Mbits)
131,072 bytes
(1 Mbit)
64
128
32
8
4
262,144 bytes
(2 Mbits)
65,536 bytes
(512 Kbits)
65,536 bytes
(512 Kbits)
65,536 bytes
(512 Kbits)
32,768 bytes
(256 Kbits)
Pages per sector
1,024
256
256
256
128
Total number of
pages
65,536
32,768
8,192
2,048
512
Bytes per page
256 bytes
256 bytes
256 bytes
256 bytes
256 bytes
Table 3–3 through Table 3–7 list the address range for each sector in EPCS128, EPCS64,
EPCS16, EPCS4, and EPCS1.
Table 3–3. Address Range for Sectors in EPCS128 (Part 1 of 3)
Address Range (Byte Addresses in HEX)
© December 2009
Altera Corporation
Sector
Start
End
63
H'FC0000
H'FFFFFF
62
H'F80000
H'FBFFFF
61
H'F40000
H'F7FFFF
60
H'F00000
H'F3FFFF
59
H'EC0000
H'EFFFFF
58
H'E80000
H'EBFFFF
57
H'E40000
H'E7FFFF
56
H'E00000
H'E3FFFF
55
H'DC0000
H'DFFFFF
54
H'D80000
H'DBFFFF
53
H'D40000
H'D7FFFF
52
H'D00000
H'D3FFFF
51
H'CC0000
H'CFFFFF
50
H'C80000
H'CBFFFF
49
H'C40000
H'C7FFFF
48
H'C00000
H'C3FFFF
Configuration Handbook (Complete Two-Volume Set)
3–8
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
Table 3–3. Address Range for Sectors in EPCS128 (Part 2 of 3)
Address Range (Byte Addresses in HEX)
Sector
Start
End
47
H'BC0000
H'BFFFFF
46
H'B80000
H'BBFFFF
45
H'B40000
H'B7FFFF
44
H'B00000
H'B3FFFF
43
H'AC0000
H'AFFFFF
42
H'A80000
H'ABFFFF
41
H'A40000
H'A7FFFF
40
H'A00000
H'A3FFFF
39
H'9C0000
H'9FFFFF
38
H'980000
H'9BFFFF
37
H'940000
H'97FFFF
36
H'900000
H'93FFFF
35
H'8C0000
H'8FFFFF
34
H'880000
H'8BFFFF
33
H'840000
H'87FFFF
32
H'800000
H'83FFFF
31
H'7C0000
H'7FFFFF
30
H'780000
H'7BFFFF
29
H'740000
H'77FFFF
28
H'700000
H'73FFFF
27
H'6C0000
H'6FFFFF
26
H'680000
H'6BFFFF
25
H'640000
H'67FFFF
24
H'600000
H'63FFFF
23
H'5C0000
H'5FFFFF
22
H'580000
H'5BFFFF
21
H'540000
H'57FFFF
20
H'500000
H'53FFFF
19
H'4C0000
H'4FFFFF
18
H'480000
H'4BFFFF
17
H'440000
H'47FFFF
16
H'400000
H'43FFFF
15
H'3C0000
H'3FFFFF
14
H'380000
H'3BFFFF
13
H'340000
H'37FFFF
12
H'300000
H'33FFFF
11
H'2C0000
H'2FFFFF
10
H'280000
H'2BFFFF
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–9
Table 3–3. Address Range for Sectors in EPCS128 (Part 3 of 3)
Address Range (Byte Addresses in HEX)
Sector
Start
End
9
H'240000
H'27FFFF
8
H'200000
H'23FFFF
7
H'1C0000
H'1FFFFF
6
H'180000
H'1BFFFF
5
H'140000
H'17FFFF
4
H'100000
H'13FFFF
3
H'0C0000
H'0FFFFF
2
H'080000
H'0BFFFF
1
H'040000
H'07FFFF
0
H'000000
H'03FFFF
Table 3–4. Address Range for Sectors in EPCS64 (Part 1 of 4)
Address Range (Byte Addresses in HEX)
© December 2009
Altera Corporation
Sector
Start
End
127
H'7F0000
H'7FFFFF
126
H'7E0000
H'7EFFFF
125
H'7D0000
H'7DFFFF
124
H'7C0000
H'7CFFFF
123
H'7B0000
H'7BFFFF
122
H'7A0000
H'7AFFFF
121
H'790000
H'79FFFF
120
H'780000
H'78FFFF
119
H'770000
H'77FFFF
118
H'760000
H'76FFFF
117
H'750000
H'75FFFF
116
H'740000
H'74FFFF
115
H'730000
H'73FFFF
114
H'720000
H'72FFFF
113
H'710000
H'71FFFF
112
H'700000
H'70FFFF
111
H'6F0000
H'6FFFFF
110
H'6E0000
H'6EFFFF
109
H'6D0000
H'6DFFFF
108
H'6C0000
H'6CFFFF
107
H'6B0000
H'6BFFFF
106
H'6A0000
H'6AFFFF
105
H'690000
H'69FFFF
104
H'680000
H'68FFFF
Configuration Handbook (Complete Two-Volume Set)
3–10
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
Table 3–4. Address Range for Sectors in EPCS64 (Part 2 of 4)
Address Range (Byte Addresses in HEX)
Sector
Start
End
103
H'670000
H'67FFFF
102
H'660000
H'66FFFF
101
H'650000
H'65FFFF
100
H'640000
H'64FFFF
99
H'630000
H'63FFFF
98
H'620000
H'62FFFF
97
H'610000
H'61FFFF
96
H'600000
H'60FFFF
95
H'5F0000
H'5FFFFF
94
H'5E0000
H'5EFFFF
93
H'5D0000
H'5DFFFF
92
H'5C0000
H'5CFFFF
91
H'5B0000
H'5BFFFF
90
H'5A0000
H'5AFFFF
89
H'590000
H'59FFFF
88
H'580000
H'58FFFF
87
H'570000
H'57FFFF
86
H'560000
H'56FFFF
85
H'550000
H'55FFFF
84
H'540000
H'54FFFF
83
H'530000
H'53FFFF
82
H'520000
H'52FFFF
81
H'510000
H'51FFFF
80
H'500000
H'50FFFF
79
H'4F0000
H'4FFFFF
78
H'4E0000
H'4EFFFF
77
H'4D0000
H'4DFFFF
76
H'4C0000
H'4CFFFF
75
H'4B0000
H'4BFFFF
74
H'4A0000
H'4AFFFF
73
H'490000
H'49FFFF
72
H'480000
H'48FFFF
71
H'470000
H'47FFFF
70
H'460000
H'46FFFF
69
H'450000
H'45FFFF
68
H'440000
H'44FFFF
67
H'430000
H'43FFFF
66
H'420000
H'42FFFF
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–11
Table 3–4. Address Range for Sectors in EPCS64 (Part 3 of 4)
Address Range (Byte Addresses in HEX)
© December 2009
Altera Corporation
Sector
Start
End
65
H'410000
H'41FFFF
64
H'400000
H'40FFFF
63
H'3F0000
H'3FFFFF
62
H'3E0000
H'3EFFFF
61
H'3D0000
H'3DFFFF
60
H'3C0000
H'3CFFFF
59
H'3B0000
H'3BFFFF
58
H'3A0000
H'3AFFFF
57
H'390000
H'39FFFF
56
H'380000
H'38FFFF
55
H'370000
H'37FFFF
54
H'360000
H'36FFFF
53
H'350000
H'35FFFF
52
H'340000
H'34FFFF
51
H'330000
H'33FFFF
50
H'320000
H'32FFFF
49
H'310000
H'31FFFF
48
H'300000
H'30FFFF
47
H'2F0000
H'2FFFFF
46
H'2E0000
H'2EFFFF
45
H'2D0000
H'2DFFFF
44
H'2C0000
H'2CFFFF
43
H'2B0000
H'2BFFFF
42
H'2A0000
H'2AFFFF
41
H'290000
H'29FFFF
40
H'280000
H'28FFFF
39
H'270000
H'27FFFF
38
H'260000
H'26FFFF
37
H'250000
H'25FFFF
36
H'240000
H'24FFFF
35
H'230000
H'23FFFF
34
H'220000
H'22FFFF
33
H'210000
H'21FFFF
32
H'200000
H'20FFFF
31
H'1F0000
H'1FFFFF
30
H'1E0000
H'1EFFFF
29
H'1D0000
H'1DFFFF
28
H'1C0000
H'1CFFFF
Configuration Handbook (Complete Two-Volume Set)
3–12
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
Table 3–4. Address Range for Sectors in EPCS64 (Part 4 of 4)
Address Range (Byte Addresses in HEX)
Sector
Start
End
27
H'1B0000
H'1BFFFF
26
H'1A0000
H'1AFFFF
25
H'190000
H'19FFFF
24
H'180000
H'18FFFF
23
H'170000
H'17FFFF
22
H'160000
H'16FFFF
21
H'150000
H'15FFFF
20
H'140000
H'14FFFF
19
H'130000
H'13FFFF
18
H'120000
H'12FFFF
17
H'110000
H'11FFFF
16
H'100000
H'10FFFF
15
H'0F0000
H'0FFFFF
14
H'0E0000
H'0EFFFF
13
H'0D0000
H'0DFFFF
12
H'0C0000
H'0CFFFF
11
H'0B0000
H'0BFFFF
10
H'0A0000
H'0AFFFF
9
H'090000
H'09FFFF
8
H'080000
H'08FFFF
7
H'070000
H'07FFFF
6
H'060000
H'06FFFF
5
H'050000
H'05FFFF
4
H'040000
H'04FFFF
3
H'030000
H'03FFFF
2
H'020000
H'02FFFF
1
H'010000
H'01FFFF
0
H'000000
H'00FFFF
Table 3–5. Address Range for Sectors in EPCS16 (Part 1 of 2)
Address Range (Byte Addresses in HEX)
Sector
Start
End
31
H'1F0000
H'1FFFFF
30
H'1E0000
H'1EFFFF
29
H'1D0000
H'1DFFFF
28
H'1C0000
H'1CFFFF
27
H'1B0000
H'1BFFFF
26
H'1A0000
H'1AFFFF
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–13
Table 3–5. Address Range for Sectors in EPCS16 (Part 2 of 2)
Address Range (Byte Addresses in HEX)
Sector
Start
End
25
H'190000
H'19FFFF
24
H'180000
H'18FFFF
23
H'170000
H'17FFFF
22
H'160000
H'16FFFF
21
H'150000
H'15FFFF
20
H'140000
H'14FFFF
19
H'130000
H'13FFFF
18
H'120000
H'12FFFF
17
H'110000
H'11FFFF
16
H'100000
H'10FFFF
15
H'0F0000
H'0FFFFF
14
H'0E0000
H'0EFFFF
13
H'0D0000
H'0DFFFF
12
H'0C0000
H'0CFFFF
11
H'0B0000
H'0BFFFF
10
H'0A0000
H'0AFFFF
9
H'090000
H'09FFFF
8
H'080000
H'08FFFF
7
H'070000
H'07FFFF
6
H'060000
H'06FFFF
5
H'050000
H'05FFFF
4
H'040000
H'04FFFF
3
H'030000
H'03FFFF
2
H'020000
H'02FFFF
1
H'010000
H'01FFFF
0
H'000000
H'00FFFF
Table 3–6. Address Range for Sectors in EPCS4 (Part 1 of 2)
Address Range (Byte Addresses in HEX)
© December 2009
Altera Corporation
Sector
Start
End
7
H'70000
H'7FFFF
6
H'60000
H'6FFFF
5
H'50000
H'5FFFF
4
H'40000
H'4FFFF
3
H'30000
H'3FFFF
2
H'20000
H'2FFFF
Configuration Handbook (Complete Two-Volume Set)
3–14
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
Table 3–6. Address Range for Sectors in EPCS4 (Part 2 of 2)
Address Range (Byte Addresses in HEX)
Sector
Start
End
1
H'10000
H'1FFFF
0
H'00000
H'0FFFF
Table 3–7. Address Range for Sectors in EPCS1
Address Range (Byte Addresses in HEX)
Sector
Start
End
3
H'18000
H'1FFFF
2
H'10000
H'17FFF
1
H'08000
H'0FFFF
0
H'00000
H'07FFF
Operation Codes
This section describes the operations that can be used to access the memory in serial
configuration devices. The DATA, DCLK, ASDI, and nCS signals access the memory in
serial configuration devices. All serial configuration device operation codes,
addresses and data are shifted in and out of the device serially, with the most
significant bit (MSB) first.
The device samples the active serial data input on the first rising edge of the DCLK
after the active low chip select (nCS) input signal is driven low. Shift the operation
code (MSB first) serially into the serial configuration device through the active serial
data input (ASDI) pin. Each operation code bit is latched into the serial configuration
device on the rising edge of the DCLK.
Different operations require a different sequence of inputs. While executing an
operation, you must shift in the desired operation code, followed by the address
bytes, data bytes, both, or neither. The device must drive nCS high after the last bit of
the operation sequence is shifted in. Table 3–8 lists the operation sequence for every
operation supported by the serial configuration devices.
For the read byte, read status, and read silicon ID operations, the shifted-in operation
sequence is followed by data shifted out on the DATA pin. You can drive the nCS pin
high after any bit of the data-out sequence is shifted out.
For the write byte, erase bulk, erase sector, write enable, write disable, and write
status operations, drive the nCS pin high exactly at a byte boundary (drive the nCS
pin high a multiple of eight clock pulses after the nCS pin is driven low); otherwise,
the operation is rejected and is not executed.
All attempts to access the memory contents while a write or erase cycle is in progress
will not be granted, and the write or erase cycle will continue unaffected.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–15
Table 3–8. Operation Codes for Serial Configuration Devices
Operation Code (1)
Address Bytes
Dummy Bytes
Data Bytes
DCLK fMAX
(MHz)
Write enable
0000 0110
0
0
0
25
Write disable
0000 0100
0
0
0
25
Read status
0000 0101
0
0
1 to infinite (2)
25
Operation
Read bytes
0000 0011
3
0
1 to infinite (2)
20
Read silicon ID (4)
1010 1011
0
3
1 to infinite (2)
25
Fast read
0000 1011
3
1
1 to infinite (2)
40
Write status
0000 0001
0
0
1
25
Write bytes
0000 0010
3
0
1 to 256 (3)
25
Erase bulk
1100 0111
0
0
0
25
Erase sector
1101 1000
3
0
0
25
1001 1111
0
2
1 to infinite (2)
25
Read Device
Identification (5)
Notes to Table 3–8:
(1) The MSB is listed first and the least significant bit (LSB) is listed last.
(2) The status register, data or silicon ID are read out at least once on the DATA pin and will continuously be read out until nCS is driven high.
(3) Write bytes operation requires at least one data byte on the DATA pin. If more than 256 bytes are sent to the device, only the last 256 bytes
are written to the memory.
(4) Read silicon ID operation is available only for EPCS1, EPCS4, EPCS16, and EPCS64.
(5) Read Device Identification operation is available only for EPCS128.
Write Enable Operation
The write enable operation code is b'0000 0110, and the MSB is listed first. The
write enable operation sets the write enable latch bit, which is bit 1 in the status
register. Always set the write enable latch bit before write bytes, write status, erase
bulk, and erase sector operations. Figure 3–5 shows the timing diagram for the write
enable operation. Figure 3–7 and Figure 3–8 show the status register bit definitions.
Figure 3–5. Write Enable Operation Timing Diagram
nCS
0
1
2
3
4
5
6
7
DCLK
Operation Code
ASDI
DATA
© December 2009
Altera Corporation
High Impedance
Configuration Handbook (Complete Two-Volume Set)
3–16
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
Write Disable Operation
The write disable operation code is b'0000 0100, with the MSB listed first. The
write disable operation resets the write enable latch bit, which is bit 1 in the status
register. To prevent the memory from being written unintentionally, the write enable
latch bit is automatically reset when implementing the write disable operation as well
as under the following conditions:
■
Power up
■
Write bytes operation completion
■
Write status operation completion
■
Erase bulk operation completion
■
Erase sector operation completion
Figure 3–6 shows the timing diagram for the write disable operation.
Figure 3–6. Write Disable Operation Timing Diagram
nCS
0
1
2
3
4
5
6
7
DCLK
Operation Code
ASDI
High Impedance
DATA
Read Status Operation
The read status operation code is b'0000 0101, with the MSB listed first. You can
use the read status operation to read the status register. Figure 3–7 and Figure 3–8
show the status bits in the status register of the serial configuration devices.
Figure 3–7. EPCS4, EPCS16, EPCS64, and EPCS128 Status Register Status Bits
Bit 7
Bit 0
BP2
BP1
BP0
WEL
WIP
Write In
Progress Bit
Block Protect Bits [2..0]
Write Enable
Latch Bit
Figure 3–8. EPCS1 Status Register Status Bits
Bit 7
Bit 0
BP1
BP0
Block Protect
Bits [1..0]
WEL
WIP
Write In
Progress Bit
Write Enable
Latch Bit
Setting the write in progress bit to 1 indicates that the serial configuration device is
busy with a write or erase cycle. Resetting the write in progress bit to 0 means no
write or erase cycle is in progress.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–17
Resetting the write enable latch bit to 0 indicates that no write or erase cycle will be
accepted. Set the write enable latch bit to 1 before every write bytes, write status,
erase bulk, and erase sector operation.
The non-volatile block protect bits determine the area of the memory protected from
being written or erased unintentionally. Table 3–9 through Table 3–13 list the
protected area in the serial configuration devices with reference to the block protect
bits. The erase bulk operation is only available when all the block protect bits are 0.
When any of the block protect bits are set to 1, the relevant area is protected from
being written by write bytes operations or erased by erase sector operations.
Table 3–9. Block Protection Bits in EPCS1
Status Register Content
Memory Content
BP1 Bit
BP0 Bit
Protected Area
Unprotected Area
0
0
None
All four sectors: 0 to 3
0
1
Sector 3
Three sectors: 0 to 2
1
0
Two sectors: 2 and 3
Two sectors: 0 and 1
1
1
All sectors
None
Table 3–10. Block Protection Bits in EPCS4
Status Register Content
Memory Content
BP2 Bit
BP1 Bit
BP0 Bit
Protected Area
Unprotected Area
0
0
0
None
All eight sectors: 0 to 7
0
0
1
Sector 7
Seven sectors: 0 to 6
0
1
0
Sectors 6 and 7
Six sectors: 0 to 5
0
1
1
Four sectors: 4 to 7
Four sectors: 0 to 3
1
0
0
All sectors
None
1
0
1
All sectors
None
1
1
0
All sectors
None
1
1
1
All sectors
None
Table 3–11. Block Protection Bits in EPCS16 (Part 1 of 2)
Status Register
Content
Memory Content
BP2
Bit
BP1
Bit
BP0
Bit
0
0
0
None
All sectors (32 sectors 0 to 31)
0
0
1
Upper 32nd (Sector 31)
Lower 31/32nds (31 sectors: 0 to 30)
0
1
0
Upper sixteenth (two sectors: 30 and 31)
Lower 15/16ths (30 sectors: 0 to 29)
0
1
1
Upper eighth (four sectors: 28 to 31)
Lower seven-eighths (28 sectors: 0 to 27)
1
0
0
Upper quarter (eight sectors: 24 to 31)
Lower three-quarters (24 sectors: 0 to 23)
1
0
1
Upper half (sixteen sectors: 16 to 31)
Lower half (16 sectors: 0 to 15)
© December 2009
Protected Area
Altera Corporation
Unprotected Area
Configuration Handbook (Complete Two-Volume Set)
3–18
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
Table 3–11. Block Protection Bits in EPCS16 (Part 2 of 2)
Status Register
Content
Memory Content
BP2
Bit
BP1
Bit
BP0
Bit
1
1
0
All sectors (32 sectors: 0 to 31)
None
1
1
1
All sectors (32 sectors: 0 to 31)
None
Protected Area
Unprotected Area
Table 3–12. Block Protection Bits in EPCS64
Status Register
Content
Memory Content
BP2
Bit
BP1
Bit
BP0
Bit
0
0
0
None
All sectors (128 sectors: 0 to 127)
0
0
1
Upper 64th (2 sectors: 126 and 127)
Lower 63/64ths (126 sectors: 0 to 125)
0
1
0
Upper 32nd (4 sectors: 124 to 127)
Lower 31/32nds (124 sectors: 0 to 123)
0
1
1
Upper sixteenth (8 sectors: 120 to 127)
Lower 15/16ths (120 sectors: 0 to 119)
1
0
0
Upper eighth (16 sectors: 112 to 127)
Lower seven-eighths (112 sectors: 0 to 111)
1
0
1
Upper quarter (32 sectors: 96 to 127)
Lower three-quarters (96 sectors: 0 to 95)
1
1
0
Upper half (64 sectors: 64 to 127)
Lower half (64 sectors: 0 to 63)
1
1
1
All sectors (128 sectors: 0 to 127)
None
Protected Area
Unprotected Area
Table 3–13. Block Protection Bits in EPCS128
Status Register
Content
Memory Content
BP2
Bit
BP1
Bit
BP0
Bit
0
0
0
None
All sectors (64 sectors: 0 to 63)
0
0
1
Upper 64th (1 sector: 63)
Lower 63/64ths (63 sectors: 0 to 62)
0
1
0
Upper 32nd (2 sectors: 62 to 63)
Lower 31/32nds (62 sectors: 0 to 61)
0
1
1
Upper 16th (4 sectors: 60 to 63)
Lower 15/16ths (60 sectors: 0 to 59)
1
0
0
Upper 8th (8 sectors: 56 to 63)
Lower seven-eighths (56 sectors: 0 to 55)
1
0
1
Upper quarter (16 sectors: 48 to 63)
Lower three-quarters (48 sectors: 0 to 47)
1
1
0
Upper half (32 sectors: 32 to 63)
Lower half (32 sectors: 0 to 31)
1
1
1
All sectors (64 sectors: 0 to 63)
None
Protected Area
Unprotected Area
You can read the status register at any time, even while a write or erase cycle is in
progress. When one of these cycles is in progress, you can check the write in progress
bit (bit 0 of the status register) before sending a new operation to the device. The
device can also read the status register continuously, as shown in Figure 3–9.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–19
Figure 3–9. Read Status Operation Timing Diagram
nCS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DCLK
Operation Code
ASDI
Status Register Out
Status Register Out
High Impedance
7
DATA
6
5
4
3
2
1
0
MSB
7
6
5
4
3
2
1
0
7
MSB
Write Status Operation
The write status operation code is b'0000 0001, with the MSB listed first. Use the
write status operation to set the status register block protection bits. The write status
operation has no effect on the other bits. Therefore, you can implement this operation
to protect certain memory sectors, as defined in Table 3–9 through Table 3–13. After
setting the block protect bits, the protected memory sectors are treated as read-only
memory. You must execute the write enable operation before the write status
operation so the device sets the status register’s write enable latch bit to 1.
The write status operation is implemented by driving nCS low, followed by shifting in
the write status operation code and one data byte for the status register on the ASDI
pin. Figure 3–10 shows the timing diagram for the write status operation. nCS must be
driven high after the eighth bit of the data byte has been latched in, otherwise, the
write status operation is not executed.
Immediately after nCS drives high, the device initiates the self-timed write status
cycle. The self-timed write status cycle usually takes 5 ms for all serial configuration
devices and is guaranteed to be less than 15 ms (refer to tWS in Table 3–16). You must
account for this delay to ensure that the status register is written with desired block
protect bits. Alternatively, you can check the write in progress bit in the status register
by executing the read status operation while the self-timed write status cycle is in
progress. The write in progress bit is 1 during the self-timed write status cycle, and 0
when it is complete.
Figure 3–10. Write Status Operation Timing Diagram
nCS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DCLK
Operation Code
Status Register
7
ASDI
6
5
4
3
2
1
0
MSB
High Impedance
DATA
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–20
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
Read Bytes Operation
The read bytes operation code is b'0000 0011, with the MSB listed first. To read the
memory contents of the serial configuration device, the device is first selected by
driving nCS low. Then, the read bytes operation code is shifted in followed by a 3-byte
address (A[23..0]). Each address bit must be latched in on the rising edge of the
DCLK. After the address is latched in, the memory contents of the specified address
are shifted out serially on the DATA pin, beginning with the MSB. For reading Raw
Programming Data files (.rpd), the content is shifted out serially beginning with the
LSB. Each data bit is shifted out on the falling edge of DCLK. The maximum DCLK
frequency during the read bytes operation is 20 MHz. Figure 3–11 shows the timing
diagram for the read bytes operation.
The first byte address can be at any location. The device automatically increments the
address to the next higher address after shifting out each byte of data. Therefore, the
device can read the whole memory with a single read bytes operation. When the
device reaches the highest address, the address counter restarts at 0x000000,
allowing the memory contents to be read out indefinitely until the read bytes
operation is terminated by driving nCS high. The device can drive nCS high any time
after data is shifted out. If the read bytes operation is shifted in while a write or erase
cycle is in progress, the operation is not executed and has no effect on the write or
erase cycle in progress.
Figure 3–11. Read Bytes Operation Timing Diagram
nCS
0
1
2
3
4
5
6
7
8
9
10
28
29
30
31
32
33
34
35
36
37
38
39
DCLK
Operation Code
24-Bit Address (1)
23
ASDI
22
21
3
2
1
0
MSB
DATA Out 1
DATA Out 2
High Impedance
DATA
7
6
5
4
3
2
1
0
7
MSB (2)
Notes to Figure 3–11:
(1) Address bit A[23] is a don't-care bit in EPCS64. Address bits A[23..21] are don't-care bits in EPCS16. Address bits A[23..19] are don'tcare bits in EPCS4. Address bits A[23..17] are don't-care bits in the EPCS1.
(2) For .rpd files, the read sequence shifts out the LSB of the data byte first.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–21
Fast Read Operation
The device is first selected by driving nCS low. The fast read instruction code is
followed by a 3-byte address (A23-A0) and a dummy byte, each bit being latched-in
during the rising edge of DCLK. Then the memory contents, at that address, is shifted
out on DATA, each bit being shifted out, at a maximum frequency of 40 MHz, during
the falling edge of DCLK.
The instruction sequence is shown in Figure 3–12.
The first byte addressed can be at any location. The address is automatically
incremented to the next higher address after each byte of data is shifted out. The
whole memory can, therefore, be read with a single fast read instruction. When the
highest address is reached, the address counter rolls over to 000000h, allowing the
read sequence to be continued indefinitely.
The fast read instruction is terminated by driving nCS high at any time during data
output. Any fast read instruction is rejected during the Erase, Program, or Write
operations without any effect on the operation that is in progress .
Figure 3–12. FAST_READ Operation Timing Diagram
nCS
0
1
2
3
4
5
6
7
8
9
10
28
29
30
31
DCLK
Operation Code
24-Bit Address (1)
23
ASDI
22
21
43
44
3
2
1
0
MSB
High Impedance
DATA
nCS
32
33
34
35
36
37
38
39
40
41
42
45
46
47
DCLK
Dummy Byte
ASDI
7
6
5
4
3
2
1
0
DATA Out 1
DATA
7
MSB
6
5
4
3
DATA Out 2
2
1
0
7
MSB
6
5
4
3
2
1
0
7
MSB
Note to Figure 3–12:
(1) Address bit A[23] is a don't-care bit in EPCS64. Address bits A[23..21] are don't-care bits in EPCS16. Address
bits A[23..19] are don't-care bits in EPCS4. Address bits A[23..17] are don't-care bits in the EPCS1.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–22
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
Read Silicon ID Operation
The read silicon ID operation code is b'1010 1011, with the MSB listed first. Only
EPCS1, EPCS4, EPCS16, and EPCS64 support this operation. It reads the serial
configuration device’s 8-bit silicon ID from the DATA output pin. If this operation is
shifted in during an erase or write cycle, it is ignored and has no effect on the cycle
that is in progress.
Table 3–14 lists the serial configuration device silicon IDs.
Table 3–14. Serial Configuration Device Silicon ID
Serial Configuration Device
Silicon ID (Binary Value)
EPCS1
b'0001 0000
EPCS4
b'0001 0010
EPCS16
b'0001 0100
EPCS64
b'0001 0110
The device implements the read silicon ID operation by driving nCS low then shifting
in the read silicon ID operation code followed by three dummy bytes on ASDI. The
serial configuration device’s 8-bit silicon ID is then shifted out on the DATA pin on the
falling edge of DCLK, as shown in Figure 3–13. The device can terminate the read
silicon ID operation by driving nCS high after the silicon ID has been read at least
once. Sending additional clock cycles on DCLK while nCS is driven low can cause the
silicon ID to be shifted out repeatedly.
Figure 3–13. Read Silicon ID Operation Timing Diagram (Note 1)
nCS
0
1
2
3
4
5
6
7
8
9
10
28
29
30
31
32
33
34
35
36
37
38
39
DCLK
Operation Code
Three Dummy Bytes
23
ASDI
22
21
3
2
1
0
MSB
Silicon ID
High Impedance
DATA
7
6
5
4
3
2
1
0
MSB
Note to Figure 3–13:
(1) Only EPCS1, EPCS4, EPCS16, and EPCS64 support Read Silicon ID operation.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–23
Read Device Identification Operation
The read device identification operation code is b’1001 1111, with the MSB listed
first. Only EPCS128 supports this operation. It reads the serial configuration device’s
8-bit device identification from the DATA output pin. If this operation is shifted in
during an erase or write cycle, it is ignored and has no effect on the cycle that is in
progress. Table 3–15 shows the serial configuration device identification.
Table 3–15. Serial Configuration Device Identification
Serial Configuration Device
Silicon ID (Binary Value)
EPCS128
b'0001 1000
The device implements the read device identification operation by driving nCS low
then shifting in the read device identification operation code followed by two dummy
byte on ASDI. The serial configuration device’s 16-bit device identification is then
shifted out on the DATA pin on the falling edge of DCLK, as shown in Figure 3–14. The
device can terminate the read device identification operation by driving nCS high
after reading the device identification at least once.
Figure 3–14. Read Device Identification Operation Timing Diagram (Note 1)
nCS
0
1
2
3
4
5
6
7
8
9
10
20
21
23
24
25
26
27
28
29
30
31
32
DCLK
Operation Code
Two Dummy Bytes
15
ASDI
14
13
3
2
1
0
MSB
Silicon ID
High Impedance
7
DATA
6
5
4
3
2
1
0
MSB
Note to Figure 3–14:
(1) Only EPCS128 supports read device identification operation.
Write Bytes Operation
The write bytes operation code is b'0000 0010, with the MSB listed first. The write
bytes operation allows bytes to be written to the memory. The write enable operation
must be executed prior to the write bytes operation to set the write enable latch bit in
the status register to 1.
The write bytes operation is implemented by driving nCS low, followed by the write
bytes operation code, three address bytes and a minimum one data byte on ASDI. If
the eight least significant address bits (A[7..0]) are not all 0, all sent data that goes
beyond the end of the current page is not written into the next page. Instead, this data
is written at the start address of the same page (from the address whose eight LSBs are
all 0). Drive nCS low during the entire write bytes operation sequence, as shown in
Figure 3–15.
If more than 256 data bytes are shifted into the serial configuration device with a write
bytes operation, the previously latched data is discarded and the last 256 bytes are
written to the page. However, if less than 256 data bytes are shifted into the serial
configuration device, they are guaranteed to be written at the specified addresses and
the other bytes of the same page are unaffected.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–24
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
If the design must write more than 256 data bytes to the memory, it needs more than
one page of memory. Send the write enable and write bytes operation codes followed
by three new targeted address bytes and 256 data bytes before a new page is written.
nCS must be driven high after the eighth bit of the last data byte has been latched in.
Otherwise, the device will not execute the write bytes operation. The write enable
latch bit in the status register is reset to 0 before the completion of each write bytes
operation. Therefore, the write enable operation must be carried out before the next
write bytes operation.
The device initiates the self-timed write cycle immediately after nCS is driven high.
Refer to tWB in Table 3–16 on page 3–27 for the self-timed write cycle time for the
respective EPCS devices. Therefore, you must account for this amount of delay before
another page of memory is written. Alternatively, you can check the status register’s
write in progress bit by executing the read status operation while the self-timed write
cycle is in progress. The write in progress bit is set to 1 during the self-timed write
cycle, and 0 when it is complete.
1
The bytes of serial configuration devices memory must be erased to all 1 or 0xFF
before write bytes operation is implemented. This can be achieved by either using the
erase sector instruction in a sector, or the erase bulk instruction throughout the entire
memory.
Figure 3–15. Write Bytes Operation Timing Diagram (Note 1)
nCS
0
1
2
3
4
5
6
7
8
9
10
28
29
30
31
32
33
34
6
5
35
36
37
38
39
40
41
42
0
7
6
5
43
44
45
46
47
2
1
0
2072 2073 2074 2075 2076 2077 2078 2079
DCLK
Operation Code
ASDI
24-Bit Address (2)
23
22
21
3
Data Byte 1
2
1
MSB
0
7
MSB (3)
4
3
Data Byte 2
2
1
MSB (3)
4
3
Data Byte 256
7
6
5
4
3
2
1
0
MSB (3)
Notes to Figure 3–15:
(1) Use the erase sector or the erase bulk instruction to initialize the memory bytes of the serial configuration devices to all 1 or 0xFF before
implementing the write bytes operation.
(2) Address bit A[23] is a don't-care bit in EPCS64. Address bits A[23..21] are don't-care bits in EPCS16. Address bits A[23..19] are
don't-care bits in EPCS4. Address bits A[23..17] are don't-care bits in EPCS1.
(3) For .rpd files, write the LSB of the data byte first.
Erase Bulk Operation
The erase bulk operation code is b'1100 0111, with the MSB listed first. The erase
bulk operation sets all memory bits to 1 or 0xFF. Similar to the write bytes operation,
the write enable operation must be executed prior to the erase bulk operation so that
the write enable latch bit in the status register is set to 1.
You can implement the erase bulk operation by driving nCS low and then shifting in
the erase bulk operation code on the ASDI pin. nCS must be driven high after the
eighth bit of the erase bulk operation code has been latched in. Figure 3–16 shows the
timing diagram.
The device initiates the self-timed erase bulk cycle immediately after nCS is driven
high. Refer to tEB in Table 3–16 for the self-timed erase bulk cycle time for the
respective EPCS devices.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Serial Configuration Device Memory Access
3–25
You must account for this delay before accessing the memory contents. Alternatively,
you can check the write in progress bit in the status register by executing the read
status operation while the self-timed erase cycle is in progress. The write in progress
bit is 1 during the self-timed erase cycle and 0 when it is complete. The write enable
latch bit in the status register is reset to 0 before the erase cycle is complete.
Figure 3–16. Erase Bulk Operation Timing Diagram
nCS
0
1
2
3
4
5
6
7
DCLK
Operation Code
ASDI
Erase Sector Operation
The erase sector operation code is b'1101 1000, with the MSB listed first. The erase
sector operation allows the user to erase a certain sector in the serial configuration
device by setting all bits inside the sector to 1 or 0xFF. This operation is useful for
users who access the unused sectors as general purpose memory in their applications.
The write enable operation must be executed prior to the erase sector operation so
that the write enable latch bit in the status register is set to 1.
The erase sector operation is implemented by first driving nCS low, then shifting in
the erase sector operation code and the three address bytes of the chosen sector on the
ASDI pin. The three address bytes for the erase sector operation can be any address
inside the specified sector. (Refer to Table 3–3 through Table 3–7 for sector address
range information.) Drive nCS high after the eighth bit of the erase sector operation
code has been latched in. Figure 3–17 shows the timing diagram.
Immediately after the device drives nCS high, the self-timed erase sector cycle is
initiated. Refer to tES in Table 3–16 for the self-timed erase sector cycle time for the
respective EPCS devices. You must account for this amount of delay before the
memory contents can be accessed. Alternatively, you can check the write in progress
bit in the status register by executing the read status operation while the erase cycle is
in progress. The write in progress bit is 1 during the self-timed erase cycle and 0 when
it is complete. The write enable latch bit in the status register resets to 0 before the
erase cycle is complete.
Figure 3–17. Erase Sector Operation Timing Diagram
nCS
0
1
2
3
4
5
6
7
8
9
28
29
30
31
DCLK
Operation Code
ASDI
24-Bit Address (1)
23
22
3
2
1
0
MSB
Note to Figure 3–17:
(1) Address bit A[23] is a don't-care bit in EPCS64. Address bits A[23..21] are don't-care bits in EPCS16. Address bits A[23..19] are don'tcare bits in EPCS4. Address bits A[23..17] are don't-care bits in EPCS1.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–26
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Power and Operation
Power and Operation
This section describes the power modes, power-on reset (POR) delay, error detection,
and initial programming state of serial configuration devices.
Power Mode
Serial configuration devices support active power and standby power modes. When
nCS is low, the device is enabled and is in active power mode. The FPGA is
configured while in active power mode. When nCS is high, the device is disabled but
could remain in active power mode until all internal cycles have completed (such as
write or erase operations). The serial configuration device then goes into stand-by
power mode. The ICC1 parameter specifies the VCC supply current when the device is
in active power mode and the ICC0 parameter specifies the current when the device is
in stand-by power mode (refer to Table 3–21).
Power-On Reset
During initial power-up, a POR delay occurs to ensure the system voltage levels have
stabilized. During AS configuration, the FPGA controls the configuration and has a
longer POR delay than the serial configuration device.
f
For the POR delay time, refer to the configuration chapter in the appropriate device
handbook.
Error Detection
During AS configuration with the serial configuration device, the FPGA monitors the
configuration status through the nSTATUS and CONF_DONE pins. If an error condition
occurs (nSTATUS drives low) or if the CONF_DONE pin does not go high, the FPGA
will begin reconfiguration by pulsing the nSTATUS and nCSO signals, which controls
the chip select pin on the serial configuration device (nCS).
After an error, configuration automatically restarts if the Auto-Restart Upon Frame
Error option is turned on in the Quartus® II software. If the option is turned off, the
system must monitor the nSTATUS signal for errors and then pulse the nCONFIG
signal low to restart configuration.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Timing Information
3–27
Timing Information
Figure 3–18 shows the timing waveform for write operation to the serial configuration
device.
Figure 3–18. Write Operation Timing
tCSH
nCS
tNCSH
tNCSSU
tCH
tCL
DCLK
tDSU
tDH
ASDI
DATA
Bit n
Bit n 1
Bit 0
High Impedance
Table 3–16 defines the serial configuration device timing parameters for write
operation.
Table 3–16. Write Operation Parameters
Symbol
Parameter
Min
Typ
Max
Unit
fWCLK
Write clock frequency (from FPGA, download cable, or
embedded processor) for write enable, write disable,
read status, read silicon ID, write bytes, erase bulk, and
erase sector operations
—
—
25
MHz
tCH
DCLK high time
20
—
—
ns
tCL
DCLK low time
20
—
—
ns
tNCSSU
Chip select (nCS) setup time
10
—
—
ns
tNCSH
Chip select (nCS) hold time
10
—
—
ns
tDSU
Data (ASDI) in setup time before rising edge on DCLK
5
—
—
ns
tDH
Data (ASDI) hold time after rising edge on DCLK
5
—
—
ns
tCSH
Chip select high time
100
—
—
ns
tWB (1)
Write bytes cycle time for EPCS1, EPCS4, EPCS16, and
EPCS64
—
1.5
5
ms
Write bytes cycle time for EPCS128
—
2.5
7
ms
tWS (1)
Write status cycle time
—
5
15
ms
tEB (1)
Erase bulk cycle time for EPCS1
—
3
6
s
Erase bulk cycle time for EPCS4
—
5
10
s
Erase bulk cycle time for EPCS16
—
17
40
s
Erase bulk cycle time for EPCS64
—
68
160
s
Erase bulk cycle time for EPCS128
—
105
250
s
Erase sector cycle time for EPCS1, EPCS4, EPCS16,
and EPCS64
—
2
3
s
Erase sector cycle time for EPCS128
—
2
6
s
tES (1)
Note to Table 3–16:
(1) These parameters are not shown in Figure 3–18.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–28
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Timing Information
Figure 3–19 shows the timing waveform for the serial configuration device's read
operation.
Figure 3–19. Read Operation Timing
nCS
tCH
DCLK
tCL
tnCLK2D
Bit N
DATA
ASDI
Bit N 1
tODIS
Bit 0
Add_Bit 0
Table 3–17 defines the serial configuration device timing parameters for read
operation.
Table 3–17. Read Operation Parameters
Symbol
1
f
Parameter
Min
Max
Unit
fRCLK
Read clock frequency (from FPGA or
embedded processor) for read bytes
operation
—
20
MHz
tCH
DCLK high time
25
—
ns
tCL
DCLK low time
25
—
ns
tODIS
Output disable time after read
—
15
ns
tnCLK2D
Clock falling edge to data
—
8
ns
Existing batches of EPCS1 and EPCS4 manufactured on 0.15 µm process geometry
support AS configuration up to 40 MHz. However, batches of EPCS1 and EPCS4
manufactured on 0.18 µm process geometry support only up to 20 MHz. EPCS16,
EPCS64, and EPCS128 are not affected.
For information about product traceability and transition date to differentiate
between 0.15 µm process geometry and 0.18 µm process geometry EPCS1 and EPCS4,
refer tothe Process Change Notification PCN 0514: Manufacturing Changes on EPCS
Family.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Timing Information
3–29
Figure 3–20 shows the timing waveform for FPGA AS configuration scheme using a
serial configuration device.
Figure 3–20. AS Configuration Timing
tCF2ST1
nCONFIG
nSTATUS
CONF_DONE
nCSO
DCLK
Read Address
ASDO
DATA0
bit N
bit N-1
bit 1
bit 0
tCD2UM (1)
INIT_DONE
User Mode
User I/O
Tri-stated with internal pull-up resistor
Note to Figure 3–20:
(1) tCD2UM is a FPGA dependent parameter. For more information, refer to the respective device configuration chapters.
f
© December 2009
For more information about the timing parameters in Figure 3–20, refer to the
respective FPGA family handbook Configuration chapter.
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–30
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Programming and Configuration File Support
Programming and Configuration File Support
The Quartus II software provides programming support for serial configuration
devices. After selecting the serial configuration device, the Quartus II software
automatically generates the Programmer Object File (.pof) to program the device. The
software allows users to select the appropriate serial configuration device density that
most efficiently stores the configuration data for a selected FPGA.
The serial configuration device can be programmed in-system by an external
microprocessor using SRunner. SRunner is a software driver developed for embedded
serial configuration device programming that you can customize to fit in different
embedded systems. The SRunner can read .rpd files and write to the serial
configuration devices. The programming time is comparable to the Quartus II
software programming time. Note that writing and reading the .rpd file to the EPCS is
different from other data and address bytes. The LSB of .rpd bytes must be shifted out
first during the read bytes instruction and the LSB of .rpd bytes must be shifted in first
during the write bytes instruction. This is because the FPGA reads the LSB of the .rpd
data first during the configuration process.
f
For more information about SRunner, refer to AN 418: SRunner: An Embedded Solution
for Serial Configuration Device Programming User Guide and the source code on the
Altera website (www.altera.com).
Serial configuration devices can be programmed using the APU with the appropriate
programming adapter (PLMSEPC-8) via the Quartus II software, USB Blaster,
EthernetBlaster, or the ByteBlaster II download cable via the Quartus II software. In
addition, many third-party programmers, such as BP Microsystems and System
General, offer programming hardware that supports serial configuration devices.
During in-system programming of a serial configuration device via the USB Blaster,
EthernetBlaster, or ByteBlaster II download cable, the cable pulls nCONFIG low to
reset the FPGA and overrides the 10-k pull-down resistor on the FPGA’s nCE pin
(refer to Figure 3–2). The download cable then uses the four interface pins (DATA, nCS,
ASDI, and DCLK) to program the serial configuration device. When the programming
is complete, the download cable releases the serial configuration device’s four
interface pins and the FPGA’s nCE pin, and pulses nCONFIG to start configuration.
The FPGA can program the serial configuration device in-system using the JTAG
interface with the Serial FlashLoader. This solution allows you to indirectly program
the serial configuration device using the same JTAG interface that is used to configure
the FPGA.
f
For more information about the Serial FlashLoader, refer to AN 370: Using the Serial
FlashLoader with the Quartus II Software.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Operating Conditions
f
3–31
For more information about programming and configuration support, refer to the
following documents:
■
Altera Programming Hardware Data Sheet
■
Programming Hardware Manufacturers
■
USB-Blaster Download Cable User Guide
■
ByteBlaster II Download Cable User Guide
■
EthernetBlaster Communications Cable User Guide
Operating Conditions
Table 3–18 through Table 3–22 provide information about absolute maximum ratings,
recommended operating conditions, DC operating conditions, and capacitance for
serial configuration devices.
Table 3–18. Absolute Maximum Ratings (Note 1)
Symbol
VCC
VI
Parameter
Condition
Min
Max
Unit
Supply voltage for EPCS1, EPCS4,
and EPCS16
With respect to ground
–0.6
4.0
V
Supply voltage for EPCS64 and
EPCS128
With respect to ground
–0.2
4.0
V
DC input voltage for EPCS1, EPCS4,
and EPCS16
With respect to ground
–0.6
4.0
V
DC input voltage for EPCS64 and
EPCS128
With respect to ground
–0.5
4.0
V
IMAX
DC VCC or GND current
—
—
15
mA
IOUT
DC output current per pin
—
–25
25
mA
PD
Power dissipation
—
54
mW
TSTG
Storage temperature
No bias
–65
150
C
TAMB
Ambient temperature
Under bias
–65
135
C
TJ
Junction temperature
Under bias
—
135
C
Min
Max
Unit
—
Table 3–19. Recommended Operating Conditions
Symbol
Parameter
Conditions
VCC
Supply voltage
(2)
2.7
3.6
V
VI
Input voltage
Respect to GND
–0.3
0.3 + VCC
V
VO
Output voltage
—
0
VCC
V
TA
Operating temperature
For commercial use
0
70
C
For industrial use
–40
85
C
For extended industrial temperature
-40
125
C
tR
Input rise time
—
—
5
ns
tF
Input fall time
—
—
5
ns
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–32
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Operating Conditions
Table 3–20. DC Operating Conditions
Symbol
Conditions
Min
Max
Unit
High-level input voltage for EPCS1,
EPCS4, and EPCS16
—
0.6 x VCC
VCC + 0.4
V
High-level input voltage for EPCS64
and EPCS128
—
0.6 x VCC
VCC + 0.2
V
VIL
Low-level input voltage
—
–0.5
0.3 x VCC
V
VOH
High-level output voltage
IOH = –100 A (3)
VCC – 0.2
—
V
VIH
Parameter
VOL
Low-level output voltage
IOL = 1.6 mA (3)
—
0.4
V
II
Input leakage current
VI = VCC or GND
–10
10
A
IOZ
Tri-state output off-state current
VO = VCC or GND
–10
10
A
Conditions
Min
Max
Unit
—
—
50
A
—
—
100
A
VCC supply current (during active power mode) for
EPCS1, EPCS4, and EPCS16
—
5
15
mA
VCC supply current (during active power mode) for
EPCS64 and EPCS128
—
5
20
mA
Min
Max
Unit
Table 3–21. ICC Supply Current
Symbol
ICC0
Parameter
VCC supply current (standby)
for EPCS1, EPCS4, and EPCS16
VCC supply current (standby)
for EPCS64 and EPCS128
ICC1
Table 3–22. Capacitance (Note 4)
Symbol
Parameter
Conditions
CIN
Input pin capacitance
VIN = 0 V
—
6
pF
COUT
Output pin capacitance
VOUT = 0 V
—
8
pF
Notes to Table 3–18 through Table 3–22:
(1) For more information, refer to the Operating Requirements for Altera Devices Data Sheet.
(2) Maximum VCC rise time is 100 ms.
(3) The IOH parameter refers to high-level TTL or CMOS output current; the I OL parameter refers to low-level TTL or CMOS output current.
(4) Capacitance is sample-tested only at TA = 25 ×C and at a 20-MHz frequency.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Pin Information
3–33
Pin Information
As shown in Figure 3–21 and Figure 3–22, the serial configuration device is an 8-pin or
16-pin device. The control pins on the serial configuration device are: serial data
output (DATA), active serial data input (ASDI), serial clock (DCLK), and chip select
(nCS). Table 3–23 lists the serial configuration device's pin descriptions.
Figure 3–21 shows the Altera serial configuration device 8-pin SOIC package and its
pin-out diagram.
Figure 3–21. Altera Serial Configuration Device 8-Pin SOIC Package Pin-Out Diagram
EPCS1, EPCS4,
or EPCS16
nCS
1
8
VCC
DATA
VCC
2
7
VCC
3
6
DCLK
GND
4
5
ASDI
Figure 3–22 shows the Altera serial configuration device 16-pin SOIC package and its
pin-out diagram.
Figure 3–22. Altera Serial Configuration Device 16-Pin SOIC Package Pin-Out Diagram
EPCS16,
EPCS64,
or EPCS128
VCC
1
16
VCC
2
15
ASDI
N.C.
3(1)
14(1)
N.C.
N.C.
4(1)
13(1)
N.C.
N.C.
5(1)
12(1)
N.C.
N.C.
6(1)
11(1)
N.C.
nCS
7
10
GND
DATA
8
9
VCC
DCLK
Note to Figure 3–22:
(1) These pins can be left floating or connected to VCC or GND, whichever is more convenient on the board.
Table 3–23. Serial Configuration Device Pin Description (Part 1 of 2)
Pin Number
in 8-Pin
SOIC
Package
Pin Number
in 16-Pin
SOIC
Package
Pin Type
DATA
2
8
Output
The DATA output signal transfers data serially out of the serial
configuration device to the FPGA during read/configuration operation.
During read/configuration operations, the serial configuration device
is enabled by pulling nCS low. The DATA signal transitions on the
falling edge of DCLK.
ASDI
5
15
Input
The AS data input signal is used to transfer data serially into the serial
configuration device. It receives the data that should be programmed
into the serial configuration device. Data is latched on the rising edge
of DCLK.
Pin
Name
© December 2009
Altera Corporation
Description
Configuration Handbook (Complete Two-Volume Set)
3–34
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Package
Table 3–23. Serial Configuration Device Pin Description (Part 2 of 2)
Pin Number
in 8-Pin
SOIC
Package
Pin Number
in 16-Pin
SOIC
Package
Pin Type
nCS
1
7
Input
The active low chip select input signal toggles at the beginning and
end of a valid instruction. When this signal is high, the device is
deselected and the DATA pin is tri-stated. When this signal is low, it
enables the device and puts the device in an active mode. After power
up, the serial configuration device requires a falling edge on the nCS
signal before beginning any operation.
DCLK
6
16
Input
DCLK is provided by the FPGA. This signal provides the timing of the
serial interface. The data presented on ASDI is latched to the serial
configuration device on the rising edge of DCLK. Data on the DATA
pin changes after the falling edge of DCLK and is latched into the
FPGA on the next falling edge.
VCC
3, 7, 8
1, 2, 9
Power
Power pins connect to 3.3 V.
GND
4
10
Ground
Ground pin.
Pin
Name
Description
As shown in Figure 3–21 and Figure 3–22, the serial configuration device is an 8-pin or
16-pin device. In order to take advantage of vertical migration from EPSCS1 to
EPCS128, Altera recommends a layout for serial configuration devices.
Pin 1 ID
Figure 3–23. Layout Recommendation for Vertical Migration from EPCS1 to EPCS128
Pin 1 ID
Package
EPCS1 and EPCS4 available in 8-pin small outline integrated circuit (SOIC) package.
EPCS16 available in 8-pin and 16-pin small outline integrated circuit (SOIC) packages.
EPCS64 and EPCS128 available in 16-pin small outline integrated circuit (SOIC)
package.
f
For more information about Altera device packaging including mechanical drawing
and specifications for this package, refer to the Altera Device Package Information Data
Sheet.
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Ordering Code
3–35
Ordering Code
Table 3–24 lists the ordering codes for serial configuration devices.
Table 3–24. Serial Configuration Device Ordering Codes
Device
Ordering Code (1)
EPCS1
EPCS1SI8
EPCS1SI8N
EPCS4
EPCS4SI8
EPCS4SI8N
EPCS16
EPCS16SI16N
EPCS16SI8N
EPCS64
EPCS64SI16N
EPCS128
EPCS128SI16N
Note to Table 3–24:
(1) N: Lead free.
Chapter Revision History
Table 3–25 lists the revision history for this chapter.
Table 3–25. Chapter Revision History (Part 1 of 3)
Date
Version
December 2009
3.3
October 2008
May 2008
© December 2009
3.2
3.1
Altera Corporation
Changes Made
■
Updated “Features” and “Functional Description” sections.
■
Added “Fast Read Operation” section.
■
Removed Table 4–2 to Table 4–9, Table 4-26, and Table 4–33.
■
Updated Table 3–1.
■
Updated Figure 3–2.
■
Removed “Referenced Documents” section.
■
Updated “Introduction”, “Active Serial FPGA Configuration”, “Operation Codes”,
“Read Status Operation”, “Read Device Identification Operation”, and “Package”
sections.
■
Updated Table 4–10, Table 4–25, Table 4–26, and Table 4–32.
■
Updated Figure 4–5, Figure 4–13, and Figure 4–19.
■
Added Figure 4–22.
■
Added Table 4–33.
■
Updated new document format.
■
Updated Table 4–3, Table 4–6, Table 4–7, Table 4–28, and Table 4–29.
■
Deleted Note 5 to Table 4–31.
■
Added “Referenced Documents” section.
Configuration Handbook (Complete Two-Volume Set)
3–36
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Chapter Revision History
Table 3–25. Chapter Revision History (Part 2 of 3)
Date
August 2007
April 2007
January 2007
October 2006
Version
3.0
2.0
1.7
1.6
Changes Made
■
Updated “Introduction” section.
■
Updated “Functional Description” section.
■
Updated Table 4–1 through Table 4–4 and Table 4–7 through Table 4–9 to with
EPCS128 information.
■
Added Table 4–6 on Arria GX.
■
Added notes to Figure 4–3.
■
Added notes to Figure 4–4.
■
Updated Table 4–10 with EPCS128 information.
■
Added new Table 4–11 on address range for sectors in EPCS128 device.
■
Updated Table 4–16 with information about “Read Device Identification” and added
(Note 5).
■
Added new Table 4–21 on block protection bits in EPCS128.
■
Added notes to Figure 4–12.
■
Added new section “Read Device Identification Operation” with Table 4–23 and
Figure 4–13.
■
Updated “Write Bytes Operation”, “Erase Bulk Operation” and “Erase Sector
Operation” sections.
■
Updated Table 4–24 to include EPCS128 information.
■
Updated (Note 1) to Table 4–26.
■
Updated VCC and VI information to include EPCS128 in Table 4–27.
■
Updated VIH information to include EPCS128 in Table 4–29.
■
Updated ICC0 and ICC1 information to include EPCS128 in Table 4–30.
■
Updated Figure 4–21 and Table 4–34 with EPCS128 information.
■
Updated “Introduction” section.
■
Updated “Functional Description” section and added handpara note.
■
Added Table 4–4, Table 4–6, and Table 4–7.
■
Updated “Active Serial FPGA Configuration” section and its handpara note.
■
Added notes to Figure 4–2.
■
Updated Table 4–26 and added (Note 1).
■
Updated Figure 4–20.
■
Updated Table 4–34.
■
Removed reference to PLMSEPC-16 in “Programming and Configuration File
Support”.
■
Updated DCLK pin information in Table 4–32.
■
Updated Figure 4–19.
■
Updated Table 4–30 and Table 4–32.
August 2005
1.5
■
Updated table 4-4 to include EPCS64 support for Cyclone devices.
August 2005
1.4
■
Updated tables.
■
Minor text updates.
■
Updated hot socketing AC specifications.
February 2005
1.3
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Chapter Revision History
3–37
Table 3–25. Chapter Revision History (Part 3 of 3)
Date
October 2003
Version
1.2
Changes Made
■
Added Serial Configuration Device Memory Access section.
■
Updated timing information in Tables 4–10 and
4–11 section.
■
Updated timing information in Tables 4-16 and 4-17.
July 2003
1.1
■
Minor updates.
May 2003
1.0
■
Added document to the Cyclone Device Handbook.
© December 2009
Altera Corporation
Configuration Handbook (Complete Two-Volume Set)
3–38
Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Chapter Revision History
Configuration Handbook (Complete Two-Volume Set)
© December 2009
Altera Corporation