REV: 13-10-01 Part Ⅰ Package Outline Drawing Part Ⅱ Carrier Tape Outline Drawing Part Ⅲ Reel Outline Drawing 1 Table of Contents Part Ⅰ - Package Outline Drawing DIP-8 PACKAGE OUTLINE DRAWING ----------------------------------------------------------- Ⅰ-1 DIP-14 PACKAGE OUTLINE DRAWIN ------------------------------------------------------------ Ⅰ-2 DIP-16 PACKAGE OUTLINE DRAWING ---------------------------------------------------------- Ⅰ-3 DIP-18 PACKAGE OUTLINE DRAWING --------------------------------------------------------- Ⅰ-4 DIP-20 PACKAGE OUTLINE DRAWING --------------------------------------------------------- Ⅰ-5 SOP-8 Exposed Pad(Heat Sink)PACKAGE OUTLINE DRAWING ------------------------- Ⅰ-6 SOP-8 PACKAGE OUTLINE DRAWING --------------------------------------------------------- Ⅰ-7 SOP-14 PACKAGE OUTLINE DRAWING -------------------------------------------------------- Ⅰ-8 SOP-16 (150 mil) PACKAGE OUTLINE DRAWING -------------------------------------------- Ⅰ-9 SOP-16 (150 mil) Exposed Pad (Heat Sink) PACKAGE OUTLINE DRAWING ---------- Ⅰ-10 SOP-16 (300 mil) PACKAGE OUTLINE DRAWING -------------------------------------------- Ⅰ-11 SOP-20 PACKAGE OUTLINE DRAWING -------------------------------------------------------- Ⅰ-12 SOP-24 PACKAGE OUTLINE DRAWING -------------------------------------------------------- Ⅰ-13 SOT-23 PACKAGE OUTLINE DRAWING -------------------------------------------------------- Ⅰ-14 SOT-23-5 PACKAGE OUTLINE DRAWING ------------------------------------------------------ Ⅰ-15 SOT-23-6 PACKAGE OUTLINE DRAWING ------------------------------------------------------ Ⅰ-16 SOT-89 PACKAGE OUTLINE DRAWING -------------------------------------------------------- Ⅰ-17 SOT-89 5PIN PACKAGE OUTLINE DRAWING ------------------------------------------------- Ⅰ-18 SOT-143 PACKAGE OUTLINE DRAWING ------------------------------------------------------- Ⅰ-19 SOT-223 PACKAGE OUTLINE DRAWING ------------------------------------------------------- Ⅰ-20 MSOP-8 PACKAGE OUTLINE DRAWING -------------------------------------------------------- Ⅰ-21 MSOP-8 Exposed Pad(Heat Sink)PACKAGE OUTLINE DRAWING ----------------------- Ⅰ-22 MSOP-10 PACKAGE OUTLINE DRAWING ------------------------------------------------------ Ⅰ-23 MSOP-10 Exposed Pad(Heat Sink)PACKAGE OUTLINE DRAWING --------------------- Ⅰ-24 TO-92 PACKAGE OUTLINE DRAWING ----------------------------------------------------------- Ⅰ-25 TO-220 PACKAGE OUTLINE DRAWING --------------------------------------------------------- Ⅰ-26 2 TO-220B PACKAGE OUTLINE DRAWING ------------------------------------------------------- Ⅰ-27 TO-220-5L PACKAGE OUTLINE DRAWING ----------------------------------------------------- Ⅰ-28 TO-252-3L PACKAGE OUTLINE DRAWING ---------------------------------------------------- Ⅰ-29 TO-252-4L PACKAGE OUTLINE DRAWING --------------------------------------------------- Ⅰ-30 TO-252-5L PACKAGE OUTLINE DRAWING --------------------------------------------------- Ⅰ-31 TO-263-3L PACKAGE OUTLINE DRAWING ---------------------------------------------------- Ⅰ-32 TO-263-5L PACKAGE OUTLINE DRAWING ---------------------------------------------------- Ⅰ-33 QFN 12L-3x3x0.6-0.65mm PACKAGE OUTLINE DRAWING ------------------------------- Ⅰ-34 QFN 12L-3x3x0.75-0.5mm PACKAGE OUTLINE DRAWING ------------------------------- Ⅰ-35 QFN 12L-3x3x0.9-0.5mm PACKAGE OUTLINE DRAWING --------------------------------- Ⅰ-36 QFN 12L-4x4x0.75-0.8mm PACKAGE OUTLINE DRAWING -------------------------------- Ⅰ-37 QFN 12L-4x4x0.9-0.8mm PACKAGE OUTLINE DRAWING --------------------------------- Ⅰ-38 QFN 16L-3x3x0.6-0.5mm PACKAGE OUTLINE DRAWING --------------------------------- Ⅰ-39 QFN 16L-3x3x0.75 -0.5mm PACKAGE OUTLINE DRAWING ------------------------------- Ⅰ-40 QFN 16L-3x3x0.9-0.5mm PACKAGE OUTLINE DRAWING --------------------------------- Ⅰ-41 QFN 16L-4x4x0.75-0.65mm PACKAGE OUTLINE DRAWING ----------------------------- Ⅰ-42 QFN 16L-4x4x0.9-0.65mm PACKAGE OUTLINE DRAWING ------------------------------- Ⅰ-43 QFN 20L-4x4x0.75-0.5 mm PACKAGE OUTLINE DRAWING ------------------------------ Ⅰ-44 QFN 20L-4x4x0.9-0.5 mm PACKAGE OUTLINE DRAWING -------------------------------- Ⅰ-45 DFN 6L-2x2x0.75-0.65mm PACKAGE OUTLINE DRAWING -------------------------------- Ⅰ-46 DFN 8L-3x3x0.75-0.65mm PACKAGE OUTLINE DRAWING -------------------------------- Ⅰ-47 DFN 10L-3x3x0.75-0.5mm PACKAGE OUTLINE DRAWING -------------------------------- Ⅰ-48 DFN 12L-3x3x0.75-0.45mm PACKAGE OUTLINE DRAWING ------------------------------- Ⅰ-49 DFN 12L-3x3x0.75-0.5mm PACKAGE OUTLINE DRAWING -------------------------------- Ⅰ-50 DFN 12L-3x3x0.75-0.5mm (Without Heat Sink) PACKAGE OUTLINE DRAWING ----- Ⅰ-51 SC70-3L PACKAGE OUTLINE DRAWING ------------------------------------------------------- Ⅰ-52 SC70-5L PACKAGE OUTLINE DRAWING ------------------------------------------------------- Ⅰ-53 SC70-6L PACKAGE OUTLINE DRAWING ------------------------------------------------------- Ⅰ-54 TSOT-23 PACKAGE OUTLINE DRAWING ------------------------------------------------------- Ⅰ-55 TSOT-23-5 PACKAGE OUTLINE DRAWING ---------------------------------------------------- Ⅰ-56 TSOT-23-6 PACKAGE OUTLINE DRAWING ---------------------------------------------------- Ⅰ-57 TSSOP-8 PACKAGE OUTLINE DRAWING ------------------------------------------------------ Ⅰ-58 3 TSSOP-16 PACKAGE OUTLINE DRAWING ---------------------------------------------------- Ⅰ-59 TSSOP-16 Exposed Pad(Heat Sink) PACKAGE OUTLINE DRAWING ------------------ Ⅰ-60 Part Ⅱ - Carrier Tape Outline Drawing SOP-8 CARRIER TAPE OUTLINE DRAWING -------------------------------------------------- Ⅱ-1 SOP-14 CARRIER TAPE OUTLINE DRAWING ------------------------------------------------- Ⅱ-2 SOP-16 CARRIER TAPE OUTLINE DRAWING ------------------------------------------------- Ⅱ-3 SOP-16W CARRIER TAPE OUTLINE DRAWING ---------------------------------------------- Ⅱ-4 SOP-20 CARRIER TAPE OUTLINE DRAWING ------------------------------------------------- Ⅱ-5 SOP-24 CARRIER TAPE OUTLINE DRAWIN --------------------------------------------------- Ⅱ-6 SOT-23/SOT-23-5/SOT-23-6 CARRIER TAPE OUTLINE DRAWING --------------------- Ⅱ-7 SOT-89 CARRIER TAPE OUTLINE DRAWING ------------------------------------------------- Ⅱ-8 SOT-143 CARRIER TAPE OUTLINE DRAWING ----------------------------------------------- Ⅱ-9 SOT-223 CARRIER TAPE OUTLINE DRAWING ----------------------------------------------- Ⅱ-10 MSOP-8/10 CARRIER TAPE OUTLINE DRAWING -------------------------------------------- Ⅱ-11 TO-252 CARRIER TAPE OUTLINE DRAWING ------------------------------------------------- Ⅱ-12 TO-263 CARRIER TAPE OUTLINE DRAWING ------------------------------------------------- Ⅱ-13 QFN 3x3x0.6 CARRIER TAPE OUTLINE DRAWING ----------------------------------------- Ⅱ-14 QFN 3x3x0.9 CARRIER TAPE OUTLINE DRAWING ----------------------------------------- Ⅱ-15 QFN 4x4x0.9 CARRIER TAPE OUTLINE DRAWING ----------------------------------------- Ⅱ-16 DFN 2x2x0.75 CARRIER TAPE OUTLINE DRAWING ---------------------------------------- Ⅱ-17 DFN 3x3x0.75 CARRIER TAPE OUTLINE DRAWING ---------------------------------------- Ⅱ-18 SC-70/SC-82 CARRIER TAPE OUTLINE DRAWING ----------------------------------------- Ⅱ-19 TSSOP-16 CARRIER TAPE OUTLINE DRAWING -------------------------------------------- Ⅱ-20 Part Ⅲ - Reel Outline Drawing REEL OUTLINE DRAWING --------------------------------------------------------------------------- Ⅲ-1 TO-92 TAPING SPEC. DRAWING ------------------------------------------------------------------ Ⅲ-1 4 Part I Package Outline Drawing (unit：mm) DIP-8 PACKAGE OUTLINE DRAWING E D 0.38 E1 GAUGE PLANE eA A A2 eB b D1 A b2 A c L A1 WITH PLATING BASE METAL SECTION A-A e S Y M B O L DIP-8 MILLIMETERS MAX. MIN. A Note: 1. Refer to JEDEC MS-001BA 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side . 3. Dimension "D1"and "E1" do not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. 5.33 A1 0.38 A2 2.92 4.95 b 0.36 0.56 b2 1.14 1.78 c 0.20 0.35 D 9.01 10.16 D1 0.13 E 7.62 8.26 E1 6.10 7.11 e 2.54 BSC eA 7.62 BSC eB L 10.92 2.92 3.81 I-1 DIP-14 PACKAGE OUTLINE DRAWING E D 0.38 E1 GAUGE PLANE eA b A A2 eB A D1 b2 A L A1 c WITH PLATING BASE METAL SECTION A-A e S Y M B O L DIP-14 MILLIMETERS MIN. MAX. A Note: 1. Refer to JEDEC MS-001AA 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side . 3. Dimension "D1"and "E1" do not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. 5.33 A1 0.38 A2 2.92 4.95 b 0.36 0.56 b2 1.14 1.78 c 0.20 0.35 D 18.67 19.69 D1 0.13 E 7.62 8.26 E1 6.10 7.11 e 2.54 BSC eA 7.62 BSC eB L 10.92 2.92 3.81 I-2 DIP-16 PACKAGE OUTLINE DRAWING E D 0.38 E1 GAUGE PLANE eA A A2 eB b A D1 b2 A c L A1 WITH PLATING BASE METAL SECTION A-A e S Y M B O L DIP-16 MILLIMETERS MAX. MIN. 5.33 A Note: 1. Refer to JEDEC MS-001BB 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side . 3. Dimension "D1"and "E1" do not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. A1 0.38 A2 2.92 4.95 b 0.36 0.56 b2 1.14 1.78 c 0.20 0.35 D 18.66 19.69 D1 0.13 E 7.62 8.26 E1 6.10 7.11 e 2.54 BSC eA 7.62 BSC eB L 10.92 2.92 3.81 I-3 DIP-18 PACKAGE OUTLINE DRAWING D S Y M B O L b2 E A L 5.33 A1 0.38 A2 2.92 4.95 b 0.36 0.56 b2 1.14 1.78 c 0.20 0.35 D 22.35 23.37 D1 0.13 E 7.62 8.26 E1 6.10 7.11 e 2.54 BSC eA 7.62 BSC eB L 10.92 2.92 3.81 b WITH PLATING c 0.38 MAX. MIN. e GAUGE PLANE eA eB MILLIMETERS A E1 A2 D1 A A1 A DIP-18 BASE METAL SECTION A-A Note: 1. Refer to JEDEC MS-001AC. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side . 3. Dimension "D1"and "E1" do not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. I-4 DIP-20 PACKAGE OUTLINE DRAWING D S Y M B O L b2 A MILLIMETERS MIN. A L e E 5.33 A1 0.38 A2 2.92 4.95 b 0.36 0.56 b2 1.14 1.78 c 0.20 0.35 D 24.89 26.92 D1 0.13 E 7.62 8.26 E1 6.10 7.11 e 2.54 BSC eA 7.62 BSC eB L eA eB 10.92 2.92 3.81 b WITH PLATING c 0.38 GAUGE PLANE MAX. A E1 A2 D1 A1 A DIP-20 BASE METAL SECTION A-A Note: 1. Refer to JEDEC MS-001AD. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side . 3. Dimension "D1"and "E1" do not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. I-5 SOP-8 Exposed Pad(Heat Sink)PACKAGE OUTLINE DRAWING D D1 EXPOSED THERMAL PAD(Heat Sink) (BOTTOM CENTER OF PACKAGE) h X 45° A A SEE VIEW B A e H E E1 WITH PLATING 0.25 C A1 B GAUGE PLANE SEATING PLANE L VIEW B BASE METAL SECTION A-A Note : 1. Refer to JEDEC MS-012E. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L SOP-8 Exposed Pad(Heat Sink) MILLIMETERS MIN. MAX. A 1.35 1.75 A1 0.00 0.15 B 0.31 0.51 C 0.17 0.25 D 4.80 5.00 D1 1.50 3.50 E 3.80 4.00 E1 1.0 e 2.55 1.27 BSC H 5.80 6.20 h 0.25 0.50 L 0.40 1.27 θ 0° 8° I-6 SOP-8 PACKAGE OUTLINE DRAWING h X 45° A A SEE VIEW B A e H E D WITH PLATING 0.25 C A1 B GAUGE PLANE SEATING PLANE θ L VIEW B BASE METAL SECTION A-A Note: 1. Refer to JEDEC MS-012AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L SOP-8 MILLIMETERS MIN. MAX. A 1.35 1.75 A1 0.10 0.25 B 0.33 0.51 C 0.19 0.25 D 4.80 5.00 E 3.80 4.00 e 1.27 BSC H 5.80 6.20 h 0.25 0.50 L 0.40 1.27 θ 0° 8° I-7 SOP-14 PACKAGE OUTLINE DRAWING e h X 45° A H E D A SEE VIEW B B BASE METAL SECTION A-A 0.25 A1 A C WITH PLATING GAUGE PLANE SEATING PLANE VIEW B θ L Note: 1. Refer to JEDEC MS-012AB. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side on. 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L SOP-14 MILLIMETERS MIN. MAX. A 1.35 1.75 A1 0.10 0.25 B 0.33 0.51 C 0.19 0.25 D 8.55 8.75 E 3.80 4.00 e 1.27 BSC H 5.80 6.20 h 0.25 0.50 L 0.40 1.27 θ 0° 8° I-8 SOP-16 (150 mil) PACKAGE OUTLINE DRAWING h X 45° A A SEE VIEW B A1 A e H E D B 0.25 C WITH PLATING SECTION A-A GAUGE PLANE SEATING PLANE θ L VIEW B BASE METAL Note: 1. Refer to JEDEC MS-012AC. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side on. 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L SOP-16(150mil) MILLIMETERS MIN. MAX. A 1.35 1.75 A1 0.10 0.25 B 0.33 0.51 C 0.19 0.25 D 9.80 10.00 E 3.80 e 4.00 1.27 BSC H 5.80 h 0.25 0.50 L 0.40 1.27 0° 8° θ 6.20 I-9 SOP-16 (150 mil) Exposed Pad (Heat Sink)PACKAGE OUTLINE DRAWING D H h X 45° A A SEE VIEW B A1 A e E E1 D1 B 0.25 C WITH PLATING GAUGE PLANE SEATING PLANE θ L VIEW B BASE METAL SECTION A-A S Y M B O L SOP-16(150mil) Exposed Pad (Heat Sink) MILLIMETERS MIN. MAX. A 1.35 1.70 A1 0.00 0.15 B 0.31 0.51 C 0.10 0.25 D 9.80 10.00 E 3.80 4.00 e Note: 1. Refer to JEDEC MS-012AC. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side on. 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. 1.27 BSC H 5.80 h 0.25 0.50 L 0.40 1.27 0° 8° D1 3.30 5.00 E1 1.30 2.80 θ 6.20 I-10 SOP-16 (300 mil) PACKAGE OUTLINE DRAWING h x 45° A A SEE VIEW B A1 A e H E D B 0.25 C WITH PLATING GAUGE PLANE SEATING PLANE θ L VIEW B BASE METAL SECTION A-A Note: 1. Refer to JEDEC MS-013AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L SOP-16(300mil) MILLIMETERS MIN. MAX. A 2.35 2.65 A1 0.10 0.30 B 0.33 0.51 C 0.23 0.32 D 10.10 10.50 E 7.40 7.60 e 1.27 BSC H 10.00 10.65 h 0.25 0.50 L 0.40 1.27 θ 0° 8° I-11 SOP-20 PACKAGE OUTLINE DRAWING h x 45° A A SEE VIEW B A1 A e H E D B 0.25 C WITH PLATING SECTION A-A GAUGE PLANE SEATING PLANE θ L VIEW B BASE METAL Note: 1. Refer to JEDEC MS-013AC. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L SOP-20 MILLIMETERS MIN. MAX. A 2.35 2.65 A1 0.10 0.30 B 0.33 0.51 C 0.23 0.32 D 12.60 13.00 E 7.40 e 7.60 1.27 BSC 10.65 H 10.00 h 0.25 0.50 L 0.40 1.27 θ 0° 8° I-12 SOP-24 PACKAGE OUTLINE DRAWING h x 45° A A SEE VIEW B A A1 e H E D B 0.25 C WITH PLATING S Y M B O L GAUGE PLANE SEATING PLANE θ L VIEW B BASE METAL SECTION A-A Note: 1. Refer to JEDEC MS-013AD. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. SOP-24 MILLIMETERS MIN. MAX. A 2.35 2.65 A1 0.10 0.30 B 0.33 0.51 C 0.23 0.32 D 15.20 15.60 E 7.40 7.60 e 1.27 BSC H 10.00 h 0.25 0.50 L 0.40 1.27 0° 8° θ 10.65 I-13 SOT-23 PACKAGE OUTLINE DRAWING D A A E E1 e e1 SEE VIEW B WITH PLATING c A A2 b BASE METAL 0.25 A1 SECTION A-A GAUGE PLANE SEATING PLANE L1 VIEW B S Y M B O L θ L Note: 1. Refer to JEDEC MO-178. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. SOT-23 MILLIMETERS MIN. MAX. A 0.95 1.45 A1 0.00 0.15 A2 0.90 1.30 b 0.30 0.50 c 0.08 0.22 D 2.80 3.00 E 2.60 3.00 E1 1.50 1.70 e 0.95 BSC e1 1.90 BSC L θ 0.60 0.30 0.60 REF L1 0° 8° I-14 SOT-23-5 PACKAGE OUTLINE DRAWING A A E E1 D e e1 SEE VIEW B WITH PLATING c A A2 b SECTION A-A 0.25 A1 BASE METAL GAUGE PLANE SEATING PLANE L1 S Y M B O L θ L VIEW B A Note : 1. Refer to JEDEC MO-178AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. SOT-23-5 MILLIMETERS MIN. MAX. 0.95 1.45 A1 0.00 0.15 A2 0.90 1.30 b 0.30 0.50 c 0.08 0.22 D 2.80 3.00 E 2.60 3.00 E1 1.50 e e1 L 1.90 BSC 0.60 0.30 L1 θ 1.70 0.95 BSC 0.60 REF 0° 8° I-15 SOT-23-6 PACKAGE OUTLINE DRAWING A A E E1 D e e1 SEE VIEW B WITH PLATING c A A2 b SECTION A-A 0.25 A1 BASE METAL GAUGE PLANE SEATING PLANE L1 S Y M B O L θ L VIEW B Note : 1. Refer to JEDEC MO-178AB. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. A SOT-23-6 MILLIMETERS MIN. MAX. 0.95 1.45 A1 0.00 0.15 A2 0.90 1.30 b 0.30 0.50 c 0.08 0.22 D 2.80 3.00 E 2.60 3.00 E1 1.50 e e1 L 1.90 BSC 0.60 0.30 L1 θ 1.70 0.95 BSC 0.60 REF 0° 8° I-16 SOT-89 PACKAGE OUTLINE DRAWING D A C L H E D1 e S Y M B O L e1 MIN. MAX. 1.40 1.60 B 0.44 0.56 B1 0.36 0.48 A B1 B SOT-89 MILLIMETERS C 0.35 0.44 D 4.40 4.60 D1 1.50 1.83 E 2.29 2.60 e 1.50 BSC e1 3.00 BSC H 3.94 4.25 L 0.89 1.20 Note: 1. Refer to JEDEC TO-243AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. I-17 SOT-89 5PIN PACKAGE OUTLINE DRAWIN D A C L H E D1 e S Y M B O L e1 SOT-89-5 MILLIMETERS MIN. MAX. A 1.40 1.60 B 0.36 0.56 C 0.35 0.44 D 4.40 4.60 D1 1.50 1.83 E 2.29 2.60 e 1.50 BSC e1 B 3.00 BSC H 3.94 4.25 L 0.80 1.20 Note: 1. Refer to JEDEC TO-243AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. I-18 SOT-143 PACKAGE OUTLINE DRAWING D e1 A E E1 e A SEE VIEW B WITH PLATING c A A2 b/b2 BASE METAL A1 SECTION A-A GAUGE PLANE SEATING PLANE 0.25 L1 θ L VIEW B Note: 1. Refer to JEDEC TO-253AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L A SOT-143 MILLIMETERS MIN. MAX. 0.80 1.22 A1 0.05 0.15 A2 0.75 1.07 b 0.30 0.50 b2 0.76 0.89 c 0.08 0.20 D 2.80 3.04 E 2.10 2.64 E1 1.20 1.40 e 1.92 BSC 0.20 BSC e1 L L1 θ 0.60 0.40 0.54 REF 0° 8° I-19 SOT-223 PACKAGE OUTLINE DRAWING D A A E E1 b2 SEE VIEW B e e1 WITH PLATING c A A2 b BASE METAL A1 SECTION A-A GAUGE PLANE SEATING PLANE 0.25 VIEW B θ L Note: 1. Refer to JEDEC TO-261AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L SOT-223 MILLIMETERS MIN. MAX. A 1.80 A1 0.02 0.10 A2 1.55 1.65 b 0.66 0.84 b2 2.90 3.10 c 0.23 0.33 D 6.30 6.70 E 6.70 7.30 E1 3.30 e e1 L θ 3.70 2.30 BSC 4.60 BSC 0.90 0° 8° I-20 MSOP-8 PACKAGE OUTLINE DRAWING A A SEE VIEW B A1 A A2 e E E1 D b 0.25 c WITH PLATING SECTION A-A GAUGE PLANE SEATING PLANE S Y M B O L θ L VIEW B BASE METAL MSOP-8 MILLIMETERS MAX. MIN. A Note: 1. Refer to JEDEC MO-187AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. 1.10 A1 0.00 0.15 A2 0.75 0.95 b 0.25 0.40 c 0.13 0.23 D 2.90 3.10 E E1 4.90 BSC e L θ 3.10 2.90 0.65 BSC 0.40 0.70 0° 8° I-21 MSOP-8 Exposed Pad (Heat Sink) PACKAGE OUTLINE DRAWING D A A SEE VIEW B A1 A A2 e E E2 EXPOSED THERMAL PAD (Heat Sink) (BOTTOM CENTER OF PACKAGE) E1 D1 b 0.25 c WITH PLATING VIEW B θ L BASE METAL SECTION A-A GAUGE PLANE SEATING PLANE Note: 1. Refer to JEDEC MO-187AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L MSOP-8 Exposed Pad(Heat Sink) MILLIMETERS MIN. MAX. A 1.10 A1 0.00 0.15 A2 0.75 0.95 b 0.22 0.38 c 0.08 0.23 3.00 BSC D E 4.90 BSC E1 3.00 BSC e L 0.65 BSC 0.40 0.80 θ 0° 8° D1 0.75 2.50 E2 0.75 2.50 I-22 MSOP-10 PACKAGE OUTLINE DRAWING E E1 D A A SEE VIEW B A1 A A2 e b 0.25 c WITH PLATING VIEW B S Y M B O L θ L BASE METAL SECTION A-A GAUGE PLANE SEATING PLANE MSOP-10 MILLIMETERS MIN. MAX. A Note: 1. Refer to JEDEC MO-187BA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. 1.10 A1 0.00 0.15 A2 0.75 0.95 b 0.15 0.30 c 0.13 0.23 D 2.90 3.10 E E1 4.90 BSC 2.90 e 3.10 0.50 BSC L 0.40 0.70 θ 0° 8° I-23 MSOP-10 Exposed Pad (Heat Sink) PACKAGE OUTLINE DRAWING D B B A1 A SEE VIEW A A2 e E E2 EXPOSED THERMAL PAD (Heat Sink) (BOTTOM CENTER OF PACKAGE) E1 D1 b 0.25 c WITH PLATING GAUGE PLANE SEATING PLANE θ L VIEW A BASE METAL SECTION B-B S Y M B O L MSOP-10 Exposed Pad (Heat Sink) MILLIMETERS MIN. 1.10 A1 0 0.15 A2 0.75 0.95 b 0.17 0.33 c 0.08 D Note: 1. Refer to JEDEC MO-187E 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. MAX. A D1 0.23 3.00 BSC 0.75 2.50 E 4.90 BSC E1 3.00 BSC E2 0.75 e 2.50 0.50 BSC L 0.40 0.80 θ 0° 8° I-24 TO-92 PACKAGE OUTLINE DRAWING E b S D S Y M B O L TO-92 MILLIMETERS MIN. MAX. A 4.32 5.33 b 0.36 0.47 D 4.45 5.20 E 3.18 4.19 e 2.42 2.66 e1 1.15 1.39 j 3.43 L 12.70 S 2.03 2.66 L A j Note: 1. Refer to JEDEC TO-226. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "A" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. e1 e I-25 TO-220 PACKAGE OUTLINE DRAWING A A1 E1 THERMAL PAD H1 Q E L L1 D1 D D2 P A b2 A e A2 S Y M B O L b c WITH PLATING BASE METAL SECTION A-A Note: 1. Refer to JEDEC TO-220AB. 2. Dimension "E" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "D1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. TO-220 MILLIMETERS MIN. MAX. A 3.56 4.82 A1 0.51 1.39 A2 2.04 2.92 b 0.38 1.01 b2 1.15 1.77 c 0.35 0.61 D 14.23 16.51 D1 8.38 9.02 D2 11.75 12.88 E 9.66 10.66 E1 6.86 e H1 L 8.90 2.54 BSC 5.85 6.85 12.70 14.73 L1 -- 6.35 P 3.54 4.08 Q 2.54 3.42 I-26 TO-220B PACKAGE OUTLINE DRAWING A E E1 F E2 THERMAL PAD d E1 L L1 D1 D2 D φ e b e1 C A1 A2 S Y M B O L TO-220B MILLIMETERS MIN. MAX. A 4.318 4.826 A1 4.250 4.550 A2 8.250 8.550 b 0.690 0.940 C 0.304 0.530 D Note : Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. 3.556(REF) D1 8.480 9.300 D2 11.75 12.88 2.743(REF) d E 9.906 10.44 E1 4.953 5.220 E2 6.86 8.90 φ 3.708 3.962 e 1.524 2.032 e1 6.604 7.112 F 1.143 1.397 L 9.880 10.64 L1 9.090 9.850 I-27 TO-220-5L PACKAGE OUTLINE DRAWING E E1 E2 F THERMAL PAD d E1 A L D1 D2 D φ e b C A1 Note : Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L TO-220-5L MILLIMETERS MIN. MAX. A 4.064 4.826 A1 2.032 2.921 b 0.635 1.016 C 0.304 0.460 D 3.429 3.683 D1 7.620 9.398 D2 11.75 12.88 d 2.620 2.870 E 9.779 10.668 E1 4.953 5.220 E2 6.86 8.90 φ 3.708 3.962 e 1.524 2.032 F 1.143 1.397 L 13.589 14.351 I-28 TO-252-3L PACKAGE OUTLINE DRAWING A E c2 E1 THERMAL PAD L4 H D D1 L3 b3 A A e SEE VIEW B S Y M B O L b c WITH PLATING BASE METAL SECTION A-A GAUGE PLANE SEATING PLANE L1 VIEW B A1 L2 L TO-252-3L MILLIMETERS MIN. MAX. A 2.19 2.38 A1 0.00 0.13 b 0.64 0.89 b3 4.95 5.46 c 0.46 0.61 c2 0.46 0.89 D 5.33 6.22 D1 4.60 6.00 E 6.35 6.73 E1 3.90 5.46 e 2.28 BSC H 9.40 10.41 L 1.40 1.78 L1 2.67 REF 0.51 BSC L2 L3 0.89 2.03 L4 -- 1.02 0° 8° Note: 1. Refer to JEDEC TO-252AA and AB. 2. Dimension "E" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "D" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. I-29 TO-252-4L PACKAGE OUTLINE DRAWING A E c2 E1 THERMAL PAD L4 H D D1 L3 b3 e A A SEE VIEW B b S Y M B O L c WITH PLATING BASE METAL SECTION A-A TO-252-4L MILLIMETERS MIN. MAX. A 2.19 2.38 A1 0.00 0.13 b 0.51 0.71 b3 4.32 5.46 c 0.46 0.61 GAUGE PLANE SEATING PLANE L1 A1 L2 L VIEW B c2 0.46 0.89 D 5.33 6.22 D1 4.90 6.00 E 6.35 6.73 E1 4.32 e H 9.40 L 1.40 10.41 1.78 2.67 REF L1 Note: 1. Refer to JEDEC TO-252AD and AB. 2. Dimension "E" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "D" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. 5.33 1.27 BSC L2 0.51 BSC L3 0.89 2.03 L4 0.6 1.0 θ 0° 8° I-30 TO-252-5L PACKAGE OUTLINE DRAWING A E c2 E1 THERMAL PAD e A H D D1 L3 b3 A SEE VIEW B S Y M B O L b c WITH PLATING BASE METAL SECTION A-A GAUGE PLANE SEATING PLANE L1 A1 L2 L VIEW B TO-252-5L MILLIMETERS MIN. MAX. A 2.19 2.38 A1 0.00 0.13 b 0.51 0.71 b3 4.32 5.46 c 0.46 0.61 0.89 c2 0.46 D 5.33 6.22 D1 4.90 6.00 E 6.35 6.73 E1 4.32 e 5.33 1.27 BSC H 9.40 L 1.40 L1 10.41 1.78 2.67 REF L2 0.51 BSC L3 0.89 2.03 θ 0° 8° Note: 1. Refer to JEDEC TO-252AD and AB. 2. Dimension "E" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "D" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. I-31 TO-263-3L PACKAGE OUTLINE DRAWING A c2 E1 THERMAL PAD L2 H D D1 L1 E A b2 A e SEE VIEW B b c WITH PLATING BASE METAL SECTION A-A L VIEW B SEATING PLANE A1 L3 GAUGE PLANE Note: 1. Refer to JEDEC TO-263AB. 2. Dimension "E" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "D" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L TO-263-3L MILLIMETERS MIN. MAX. A 4.06 4.83 A1 0.00 0.25 b 0.51 0.99 b2 1.14 1.78 c 0.38 0.74 c2 1.14 1.65 D 8.38 9.65 D1 6.86 -- E 9.65 10.67 E1 6.23 -- e 2.54 BSC H 14.61 L 1.78 2.79 L1 -- 1.68 L2 -- 1.78 0.25 BSC L3 θ 15.88 0° 8° I-32 TO-263-5L PACKA GE OUTLINE DRAWING A c2 E1 THERMAL PAD H D D1 L1 E A A e SEE VIEW B b c WITH PLATING BASE METAL SECTION A-A A SEATING PLANE A1 L3 GAUGE PLANE L VIEW B S Y M B O L Note: 1. Refer to JEDEC TO-263BA. 2. Dimension "E" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "D" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. TO-263-5L MILLIMETERS MIN. MAX. 4.06 4.83 A1 0.00 0.25 b 0.51 0.99 c 0.38 0.74 c2 1.14 1.65 D 8.38 9.65 D1 6.86 -- E 9.65 10.67 E1 6.23 -- e 1.70 BSC H 14.61 15.88 L 1.78 2.79 L1 -- 1.68 L3 θ 0.25 BSC 0° 8° I-33 QFN 12L-3x3x0.6-0.65mm PACKAGE OUTLINE DRAWING D2 11 12 L 12 D 11 1 2 2 E E2 1 A3 A A1 θ b e INDEX AREA (D/2*E/2) Note : 1. Refer to JEDEC MO-220 VEEC-1. 2. All dimensions are in millimeters, θ is in degrees. S Y M B O L QFN 12L-3x3x0.6-0.65mm MILLIMETERS MIN. MAX. A 0.55 0.65 A1 0.00 A3 0.05 0.20 REF b 0.25 0.35 D 2.90 3.10 1.80 D2 1.50 E 2.90 3.10 E2 1.50 1.80 0.70 e 0.60 L 0.35 0.45 θ 0 12 I-34 QFN 12L-3x3x0.75-0.5mm PACKAGE OUTLINE DRAWING D2 11 12 1 2 2 E 1 A3 A A1 θ b e INDEX AREA (D/2*E/2) E2 L 12 D 11 S Y M B O L QFN 12L-3x3x0.75-0.5mm MILLIMETERS MIN. MAX. A 0.70 0.80 A1 0.00 A3 Note : 1. Refer to JEDEC MO-220 WEED-3, 5 2. All dimensions are in millimeters, θ is in degrees. 0.05 0.20 REF b 0.18 0.30 D 2.90 3.10 D2 1.25 1.80 E 2.90 3.10 E2 1.25 1.80 0.50 BSC e L 0.35 0.45 θ 0 14 I-35 QFN 12L-3x3x0.9-0.5mm PACKAGE OUTLINE DRAWING D D2 11 11 12 1 2 2 E 1 A3 A A1 θ b e INDEX AREA (D/2*E/2) E2 L 12 S Y M B O L QFN 12L-3x3x0.9-0.5mm MILLIMETERS MIN. MAX. A 0.80 1.00 A1 0.00 0.05 A3 Note : 1. Refer to JEDEC MO-220 VEED-3. 2. All dimensions are in millimeters, θ is in degrees. 0.20 REF b 0.18 D 2.90 3.10 D2 1.50 1.80 0.30 E 2.90 3.10 E2 1.50 1.80 e 0.45 0.55 L 0.35 0.45 θ 0 12 I-36 QFN 12L-4x4x0.75 -0.8mm PACKAGE OUTLINE DRAWING D D2 11 11 12 1 2 2 E 1 A A1 θ b e INDEX AREA (D/2*E/2) E2 L 12 A3 S Y M B O L QFN 12L-4x4x0.75-0.8mm MILLIMETERS MIN. A 0.70 0.80 A1 0.00 0.05 A3 Note: 1. Refer to JEDEC MO-220 WGGB. 2. All dimensions are in millimeters, θ is in degrees. MAX. 0.20 REF b 0.25 0.35 D 3.90 4.10 D2 0.75 2.35 E 3.90 4.10 E2 0.75 2.35 0.80BSC e L 0.47 0.63 θ 0 14 I-37 QFN 12L-4x4x0.9-0.8mm PACKAGE OUTLINE DRAWING D D2 11 11 12 1 2 2 E 1 A3 A A1 θ b e INDEX AREA (D/2*E/2) E2 L 12 S Y M B O L Note : 1. Refer to JEDEC MO-220 VGGB. 2. All dimensions are in millimeters, θ is in degrees. QFN 12L-4x4x0.9-0.8mm MILLIMETERS MIN. MAX. A 0.80 1.00 A1 0.00 0.05 A3 0.20 REF b 0.25 0.35 D 3.90 4.10 D2 0.75 2.25 E 3.90 4.10 E2 0.75 2.25 e 0.75 0.85 L 0.35 0.75 θ 0 12 I-38 QFN 16L-3x3x0.6-0.5mm PACKAGE OUTLINE DRAWING D2 L D 1 2 E 2 b A3 A A1 θ e INDEX AREA (D/2*E/2) E2 1 S Y M B O L QFN 16L-3x3x0.6-0.5mm MILLIMETERS MIN. MAX. A 0.55 0.65 A1 0.00 A3 b Note: 1. Refer to JEDEC MO-220 WEED-4,6,7 2. All dimensions are in millimeters, θ is in degrees. 0.05 0.20 REF 0.30 0.18 D 2.90 3.10 D2 1.05 1.80 E 2.90 3.10 E2 1.05 1.80 0.50 BSC e L 0.30 0.55 θ 0 14 I-39 QFN 16L-3x3x0.75 -0.5mm PACKAGE OUTLINE DRAWING D2 L D 1 2 E 2 b A3 A A1 e INDEX AREA (D/2*E/2) E2 1 S Y M B O L QFN 16L-3x3x0.75-0.5mm MILLIMETERS MIN. 0.70 0.80 A1 0.00 0.05 A3 Note: 1. Refer to JEDEC MO-220 WEED-4,6,7 2. All dimensions are in millimeters, θ is in degrees. M AX. A 0.20 REF 0.30 b 0.18 D 2.90 3.10 D2 1.05 1.80 E 2.90 3.10 E2 1.05 1.80 0.50 BSC e L 0.30 0.55 θ 0 14 I-40 QFN 16L-3x3x0.9-0.5mm PACKAGE OUTLINE DRAWING D2 L D 1 2 E 2 b A3 A A1 θ e INDEX AREA (D/2*E/2) E2 1 S Y M B O L QFN 16L-3x3x0.9-0.5mm MILLIMETERS MIN. MAX. A 0.80 1.00 A1 0.00 A3 Note: 1. Refer to JEDEC MO-220 VEED-4,6,7 2. All dimensions are in millimeters, θ is in degrees. b 0.05 0.20 REF 0.18 0.30 D 2.90 3.10 D2 1.05 1.80 E 2.90 3.10 E2 1.05 1.80 0.50 BSC e L 0.30 0.55 θ 0 14 I-41 QFN 16L-4x4x0.75-0.65mm PACKAGE OUTLINE DRAWING D 15 16 1 2 2 E 1 b A3 A A1 θ e INDEX AREA (D/2*E/2) E2 L 16 D2 15 Note : 1. Refer to JEDEC MO-220 WGGC-4 2. All dimensions are in millimeters, θ is in degrees. S Y M B O L QFN 16L-4x4x0.75-0.65mm MILLIMETERS MIN. MAX. A 0.70 0.80 A1 0.00 A3 0.05 0.20 REF 0.35 b 0.25 D 3.90 4.10 D2 2.00 2.80 E 3.90 4.10 E2 2.00 2.80 0.65 BSC e L 0.30 0.65 θ 0 14 I-42 QFN 16L-4x4x0.9-0.65mm PACKAGE OUTLINE DRAWING D2 L D 1 2 E 2 b A3 A A1 θ e INDEX AREA (D/2*E/2) E2 1 S Y M B O L Note: 1. Refer to JEDEC MO-220 VGGC-2,3,4 2. All dimensions are in millimeters, θ is in degrees. QFN 16L-4x4x0.9-0.65mm MILLIMETERS MIN. MAX. A 0.80 1.00 A1 0.00 0.05 A3 0.20 REF b 0.25 D 3.90 4.10 D2 2.20 2.80 E 3.90 4.10 E2 2.20 2.80 0.35 0.65 BSC e L 0.30 0.65 θ 0 14 I-43 QFN 20L-4x4x0.75-0.5 mm PACKAGE OUTLINE DRAWING D D2 19 19 20 L 20 1 2 2 E E2 1 A3 A A1 θ b e INDEX AREA (D/2*E/2) S Y M B O L Note : 1. Refer to JEDEC MO-220 WGGD-1, 5 2. All dimensions are in millimeters, θ is in degrees. QFN 20L-4x4x0.75-0.5mm MILLIMETERS MIN. MAX. A 0.70 0.80 A1 0.00 A3 0.05 0.20 REF b 0.18 0.30 D 3.90 4.10 D2 2.25 2.80 E 3.90 4.10 E2 2.25 2.80 0.50 BSC e L 0.35 0.45 θ 0 14 I-44 QFN 20L-4x4x0.9-0.5 mm PACKAGE OUTLINE DRAWING D2 L D 1 2 2 E E2 1 A A1 θ b e INDEX AREA (D/2*E/2) A3 S Y M B O L QFN 20L-4x4x0.9-0.5mm MILLIMETERS MIN. MAX. A 0.80 1.00 A1 0.00 A3 Note: 1. Refer to JEDEC MO-220 VGGD-5 2. All dimensions are in millimeters, θ is in degrees. 0.05 0.20 REF b 0.18 0.30 D 3.90 4.10 D2 2.25 2.80 E 3.90 4.10 E2 2.25 2.80 0.50 BSC e L 0.35 0.50 θ 0 14 I-45 DFN 6L-2x2x0.75-0.65mm PACKAGE OUTLINE DRAWING D2 D 6 E E2 L 4 3 1 e PIN#1 BOTTOM VIEW TOP VIEW A3 A S Y M B O L A DFN 6L-2x2x0.75-0.65mm MILLIMETERS MIN. MAX. 0.70 0.80 A3 b b SEATING PLANE 0.20 BSC D D2 2.00 BSC E2 2.00 BSC 0.85 0.55 0.65 BSC e L 1.60 1.10 E SIDE VIEW 0.35 0.20 0.25 0.45 Note : 1. DIMENSION AND TOLERANCING CONFORM TO ASME Y14.5M-1994. 2.CONTROLLING DIMENSIONS：MILLIMETER，CONVERTED INCH DIMENSION ARE NOT NECESSARILY EXACT. 3.DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.10 AND 0.25 mm FROM TERMINAL TIP. I-46 DFN 8L-3x3x0.75-0.65mm PACKAGE OUTLINE DRAWING D2 D 8 E E2 L 5 4 PIN#1 A3 A S Y M B O L A b SEATING PLANE e 1 DFN 8L-3x3x0.75-0.65mm MILLIMETERS MIN. MAX. 0.70 0.80 A3 0.20 REF b 0.25 0.35 D 2.90 3.10 D2 2.20 2.40 E 2.90 3.10 E2 1.40 1.60 0.65 BSC e L 0.25 0.45 Note : 1. Refer to JEDEC MO-220K. 2.CONTROLLING DIMENSIONS：MILLIMETER，CONVERTED INCH DIMENSION ARE NOT NECESSARILY EXACT. I-47 DFN 10L-3x3x0.75-0.5mm PACKAGE OUTLINE DRAWING D2 D 6 E E2 L 10 5 A3 A PIN#1 b S Y M B O L A SEATING PLANE 1 e DFN 10L-3x3x0.75-0.5mm MILLIMETERS MIN. MAX. 0.70 0.80 A3 0.20 BSC b 0.18 D 2.90 3.10 D2 2.20 2.70 E 2.90 3.10 E2 1.40 1.80 0.5 BSC e L 0.30 0.30 0.50 Note : 1. DIMENSION AND TOLERANCING CONFORM TO ASME Y14.5M-1994. 2.CONTROLLING DIMENSIONS：MILLIMETER，CONVERTED INCH DIMENSION ARE NOT NECESSARILY EXACT. I-48 DFN 12L-3x3x0.75-0.45mm PACKAGE OUTLINE DRAWING D2 D 12 E E2 L 7 6 A A3 b S Y M B O L A SEATING PLANE 1 e PIN#1 DFN 12L-3x3x0.75-0.45mm MILLIMETERS MIN. MAX. 0.80 0.70 A3 0.20 BSC b 0.18 0.30 D 2.90 3.10 D2 2.20 2.70 E 2.90 3.10 E2 1.40 L 1.80 0.45 BSC e 0.30 0.50 Note : 1. DIMENSION AND TOLERANCING CONFORM TO ASME Y14.5M-1994. 2.CONTROLLING DIMENSIONS：MILLIMETER，CONVERTED INCH DIMENSION ARE NOT NECESSARILY EXACT. I-49 DFN 12L-3x3x0.75-0.5mm PACKAGE OUTLINE DRAWING D2 D 12 E E2 L 7 6 A A3 b S Y M B O L A SEATING PLANE 1 e PIN#1 DFN 12L-3x3x0.75-0.5mm MILLIMETERS MIN. MAX. 0.80 0.70 A3 0.20 BSC b 0.18 0.30 D 2.90 3.10 D2 2.20 2.40 E 2.90 3.10 E2 1.60 L 1.80 0.50 BSC e 0.35 0.45 Note : 1. DIMENSION AND TOLERANCING CONFORM TO ASME Y14.5M-1994. 2.CONTROLLING DIMENSIONS：MILLIMETER，CONVERTED INCH DIMENSION ARE NOT NECESSARILY EXACT. I-50 DFN 12L-3x3x0.75-0.5mm (Without Heat Sink) PACKAGE OUTLINE DRAWING D 12 E L 7 6 TOP VIEW BOTTOM VIEW A3 A S Y M B O L A b SEATING PLANE SIDE VIEW 1 e PIN#1 DFN 12L-3x3x0.75-0.5mm (Without Heat Sink) MILLIMETERS MIN. MAX. 0.70 0.80 A3 0.203 BSC b 0.20 0.30 D 2.90 3.10 E 2.90 3.10 e L 0.500 BSC 0.60 0.70 Note : 1. DIMENSION AND TOLERANCING CONFORM TO ASME Y14.5M-1994. 2.CONTROLLING DIMENSIONS：MILLIMETER，CONVERTED INCH DIMENSION ARE NOT NECESSARILY EXACT. I-51 SC70-3L PACKAGE OUTLINE DRAWING D A A E E1 e e1 SEE VIEW B WITH PLATING c A A2 b BASE METAL 0.15 A1 SECTION A-A L GAUGE PLANE SEATING PLANE L1 VIEW B Note: 1. Refer to JEDEC M O-203. 2. Dim ension "D" does not include m old flash, protrusions or gate burrs. M old flash, protrusion or gate burrs shall not exceed 6 m il per side. 3. Dim ension "E1" does not include inter-lead flash or protrusi ons. 4. Controlling dim ension is m illim eter, converted inch dim ensions are not necessarily exact. S Y M B O L SC70-3L MILLIMETERS MIN. MAX. A - 1.10 A1 0 0.10 A2 0.70 1.00 b 0.15 0.40 c 0.08 0.25 D 1.85 2.15 E 1.80 2.40 E1 1.10 1.40 e 0.65 BSC e1 1.30 BSC L L1 0.46 0.26 0.42 REF I-52 SC70-5L PACKAGE OUTLINE DRAWING A A E E1 D e e1 SEE VIEW B WITH PLATING c A A2 b SECTION A-A 0.15 A1 BASE METAL L GAUGE PLANE SEATING PLANE L1 VIEW B Note: 1. Refer to JEDEC MO-203AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions . 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L SC70-5L MILLIMETERS MIN. MAX. A - 1.10 A1 0 0.10 A2 0.70 1.00 b 0.15 0.30 c 0.08 0.25 D 1.85 2.15 E 1.80 2.40 E1 1.10 1.40 e 0.65 BSC e1 1.30 BSC L L1 0.46 0.26 0.42 REF I-53 SC70-6L PACKAGE OUTLINE DRAWING A A E E1 D e e1 SEE VIEW B WITH PLATING c A A2 b SECTION A-A 0.15 A1 BASE METAL L GAUGE PLANE SEATING PLANE L1 VIEW B Note: 1. Refer to JEDEC MO-203AB. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L A SC70-6L MILLIMETERS MIN. MAX. - 1.10 A1 0 0.10 A2 0.70 1.00 b 0.15 0.30 c 0.08 0.25 D 1.85 2.15 E 1.80 2.40 E1 1.10 1.40 e 0.65 BSC e1 1.30 BSC L L1 0.26 0.46 0.42 REF I-54 TSOT-23 PACKAGE OUTLINE DRAWING D A A E E1 e e1 SEE VIEW B WITH PLATING c A A2 b BASE METAL L2 A1 SECTION A-A GAUGE PLANE SEATING PLANE L1 VIEW B θ L Note : 1. Refer to JEDEC MO-193C. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L TSOT-23 MILLIMETERS MIN. MAX. - 1.00 A1 0 0.10 A2 0.70 0.90 b 0.30 0.50 c 0.08 0.22 D 2.80 3.00 E 2.60 3.00 E1 1.50 A e e1 L 1.90 BSC 0.60 0.30 0.60 REF L1 0.25 BSC L2 θ 1.70 0.95 BSC 0° 8° I-55 TSOT-23-5 PACKAGE OUTLINE DRAWING A A E E1 D e e1 SEE VIEW B WITH PLATING c A A2 b SECTION A-A 0.25 A1 BASE METAL VIEW B θ L L1 S Y M B O L GAUGE PLANE SEATING PLANE TSOT-23-5 MILLIMETERS MIN. MAX. A - 1.00 A1 0 0.10 A2 0.70 0.90 b 0.30 0.50 c 0.08 0.22 D 2.80 3.00 Note : 1. Refer to JEDEC MO-193AB. E 2. Dimension "D" does not include mold flash, protrusions E1 or gate burrs. Mold flash, protrusion or gate burrs shall not e exceed 6 mil per side. e1 3. Dimension "E1" does not include inter-lead flash or protrusions. L 4. Controlling dimension is millimeter, converted inch L1 dimensions are not necessarily exact. θ 2.60 3.00 1.50 1.70 0.95 BSC 1.90 BSC 0.60 0.30 0.60 REF 0° 8° I-56 TSOT-23-6 PACKAGE OUTLINE DRAWING A A E E1 D e e1 SEE VIEW B WITH PLATING c A A2 b SECTION A-A 0.25 A1 BASE METAL GAUGE PLANE SEATING PLANE L1 θ L VIEW B Note : 1. Refer to JEDEC MO-193AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L TSOT-23-6 MILLIMETERS MIN. MAX. - 1.00 A1 0 0.10 A2 0.70 0.90 b 0.30 0.50 c 0.08 0.22 D 2.80 3.00 E 2.60 3.00 E1 1.50 1.70 A e 0.95 BSC e1 1.90 BSC L θ 0.60 0.30 L1 0.60 REF 0° 8° I-57 TSSOP-8 PACKAGE OUTLINE DRAWING e A E E1 D A SEE VIEW B A A1 A2 e/2 b 0.25 c WITH PLATING VIEW B θ L BASE METAL SECTION A-A GAUGE PLANE SEATING PLANE Note: 1. Refer to JEDEC MO-153AA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L TSSOP-8 MILLIMETERS MAX. MIN. A 1.20 A1 0.05 0.15 A2 0.80 1.05 b 0.19 0.30 c 0.09 0.20 D 2.90 E E1 θ 4.50 4.30 e L 3.10 6.40 BSC 0.65 BSC 0.45 0.75 0° 8° I-58 TSSOP-16 PACKAGE OUTLINE DRAWING A A1 A2 SEE VIEW B A A e/2 e E E1 D b 0.25 c WITH PLATING VIEW B S Y M B O L θ L BASE METAL SECTION A-A GAUGE PLANE SEATING PLANE TSSOP-16 MILLIMETERS MAX. MIN. A Note: 1. Refer to JEDEC MO-153AB. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. 1.20 A1 0.05 0.15 A2 0.80 1.05 b 0.19 0.30 c 0.09 0.20 D 4.90 E E1 4.30 e L θ 5.10 6.40 BSC 4.50 0.65 BSC 0.45 0.75 0° 8° I-59 TSSOP-16 Exposed Pad(Heat Sink) PACKAGE OUTLINE DRAWIN D EXPOSED THERMAL PAD(Heat Sink) (BOTTOM CENTER OF PACKAGE) e/2 A SEE VIEW B A A A1 A2 e E1 E2 E D1 b 0.25 c WITH PLATING VIEW B θ L BASE METAL SECTION A-A GAUGE PLANE SEATING PLANE Note: 1. Refer to JEDEC MO-153AB. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. 3. Dimension "E1" does not include inter-lead flash or protrusions. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. S Y M B O L TSSOP-16 Exposed Pad (Heat Sink) MILLIMETERS MIN. MAX. A 1.20 A1 0.00 0.15 A2 0.80 1.05 b 0.19 0.30 c 0.09 0.20 D 4.90 E E1 4.30 e L 5.10 6.40 BSC 4.50 0.65 BSC 0.45 0.75 θ 0° 8° D1 2.00 4.00 E2 1.80 3.40 I-60 Part II Carrier Tape Outline Drawing (unit: mm) SOP-8 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko Ao B φD1 A B T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko T SPEC. 6.30±0.20 5.20±0.20 2.10±0.20 0.30±0.05 SYMBOL Po P1 P2 E1 SPEC. 4.00±0.10 8.00±0.10 2.00±0.05 1.75±0.10 Do 1.50 D1 +0.10 1.50 min. -0.00 F W 5.50±0.05 12.00±0.30 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-1 SOP-14 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko Ao B φ D1 B A T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko T Do D1 SPEC. 6.5 ±0.2 9.2 ±0.35 2.1 ±0.2 0.30 ±0.05 + 0.1 1.5 - 0.0 1.50 min. SYMBOL Po P1 P2 E1 F W SPEC. 4.0 ±0.1 8.0 ±0.1 2.0 ±0.1 1.75 ±0.1 7.5 ±0.1 16.0 ±0.3 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-2 SOP-16 CARRIER TAPE OUTLINE DRAWING φDo P2 P1 A Bo W F E1 Po Ko Ao B φD1 B A T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko T Do D1 SPEC. 6.5 ±0.2 10.3 ±0.2 2.1 ±0.2 0.30 ±0.05 + 0.1 1.5 - 0.0 1.50 min. SYMBOL Po P1 P2 E1 F W SPEC. 4.0 ±0.1 8.0 ±0.1 2.0 ±0.1 1.75 ±0.1 7.5 ±0.1 16.0 ±0.3 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-3 SOP-16W CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko B Ao φD1 B A T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko T Do D1 SPEC. 10.9 ±0.2 10.7 ±0.2 3.2 ±0.2 0.30 ±0.05 + 0.1 1.5 - 0.0 1.50 min. SYMBOL Po P1 P2 E1 F W SPEC. 4.0 ±0.1 12.0 ±0.1 2.0 ±0.1 1.75 ±0.1 7.5 ±0.1 16.0 ±0.3 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-4 SOP-20 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko Ao B φD1 A B T SECTION A-A SECTION B-B SYMBOL SPEC. SYMBOL SPEC. Ao Bo 10.90±0.20 13.30±0.20 Po P1 4.00±0.10 12.00±0.10 Ko T 3.10±0.20 0.30±0.05 P2 E1 2.00±0.10 Do 1.50 +0.10 -0.00 F D1 1.50 min. W 1.75±0.10 11.50±0.10 24.00±0.30 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-5 SOP-24 CARRIER TAPE OUTLINE DRAWIN Po P2 P1 A Bo W F E1 φDo Ko Ao B φD1 A B T SECTION A-A SECTION B-B SYMBOL SPEC. SYMBOL SPEC. Ao Bo Ko 10.90±0.20 15.90±0.20 3.10±0.20 Po P1 P2 4.00±0.10 12.00±0.10 2.00±0.10 T 0.30±0.05 E1 1.75±0.10 Do 1.50 D1 +0.10 1.50 min. -0.00 F W 11.50±0.10 24.00±0.30 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-6 SOT-23/SOT-23-5/SOT-23-6 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A W Bo F E1 φDo Ko B Ao T SECTION A-A A φD1 B SECTION B-B SYMBOL Ao Bo Ko T Do SPEC. 3.15±0.20 3.20±0.20 1.45±0.25 0.22±0.05 SYMBOL Po P1 P2 E1 F W SPEC. 4.00±0.10 4.00±0.10 2.00±0.05 1.75±0.10 3.50±0.05 8.00±0.30 1.50 +0.10 -0.00 D1 1.00 min. Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-7 SOT-89 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko Ao B φD1 A B T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko T SPEC. 4.80±0.20 4.50±0.20 1.80±0.20 0.30±0.05 SYMBOL Po P1 P2 E1 F W SPEC. 4.00±0.10 8.00±0.10 2.00±0.05 1.75±0.10 5.50±0.05 12.00±0.30 Do 1.50 +0.10 -0.00 D1 1.50 min. Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-8 SOT-143 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A W Bo F E1 φDo Ko B Ao T SECTION A-A A φD1 B SECTION B-B SYMBOL Ao Bo Ko T SPEC. 3.20±0.20 2.70±0.20 1.35±0.20 0.20±0.03 SYMBOL Po P1 P2 E1 F W SPEC. 4.00±0.10 4.00±0.10 2.00±0.05 1.75±0.10 3.50±0.05 8.00±0.30 Do 1.50 D1 +0.10 1.00 min. -0.00 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-9 SOT-223 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko Ao B φD1 A B T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko T SPEC. 6.90±0.20 7.50±0.20 2.10±0.20 0.30±0.05 SYMBOL Po P1 P2 E1 SPEC. 4.00±0.10 8.00±0.10 2.00±0.05 1.75±0.10 Do 1.50 D1 +0.10 1.50 min. -0.00 F W 5.50±0.05 12.00±0.30 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-10 MSOP-8/10 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko Ao B A φD1 B T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko T SPEC. 5.20±0.20 3.30± 0.20 1.60±0.20 0.30±0.05 SYMBOL Po P1 P2 E1 SPEC. 4.00± 0.10 8.00± 0.10 2.00±0.05 1.75±0.10 Do 1.50 +0.10 -0.00 D1 1.50 min. F W 5.50±0.05 12.00± 0.30 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-11 TO-252 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko Ao B φD1 B A T SECTION A-A SECTION B-B SYMBOL SPEC. Ao Bo Ko 6.90±0.20 10.50±0.20 2.60±0.20 T 0.30±0.05 SYMBOL Po P1 P2 E1 SPEC. 4.00±0.10 8.00±0.10 2.00±0.10 1.75±0.10 Do D1 1.50 +0.10 1.50 min. -0.00 F W 7.50±0.10 16.00±0.30 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-12 TO-263 CARRIER TAPE OUTLINE DRAWING φDo P1 A Bo W F E1 Po P2 Ko Ao B φD1 A B T SECTION A-A SECTION B-B SYMBOL SPEC. SYMBOL SPEC. Ao Bo Ko 10.60±0.20 16.10±0.50 4.90±0.20 *Note6 Po P1 P2 4.00±0.10 16.00±0.10 2.00±0.10 T Do 0.35±0.05 1.50 E1 D1 +0.10 1.50 min. -0.00 F W 1.75±0.10 11.50±0.10 24.00±0.30 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier 6. Ao and Bo must keep the lateral movement of the component within 1.0 mm in the pocket II-13 QFN 3x3x0.6 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko B Ao A φD1 B T SECTION A-A SECTION B-B Do SYMBOL Ao Bo Ko T SPEC. 3.30±0.20 3.30±0.20 0.90±0.20 0.30±0.05 SYMBOL Po P1 P2 E1 F W SPEC. 4.00±0.10 8.00±0.10 2.00±0.05 1.75±0.10 5.50±0.05 12.00±0.30 1.50 +0.10 -0.00 D1 1.50 min. Note : 1. 10 sprocket hole pitch cumulative tolerance ± 0.2 2. Material: conductive polystyrene 3. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 4 Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-14 QFN 3x3x0.9 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A φD1 B A Bo W F E1 φDo Ko Ao B T SECTION A-A SECTION B-B Do SYMBOL Ao Bo Ko T SPEC. 3.30±0.20 3.30±0.20 1.20±0.20 0.30±0.05 SYMBOL Po P1 P2 E1 F W SPEC. 4.00±0.10 8.00±0.10 2.00±0.05 1.75±0.10 5.50±0.05 12.00±0.30 1.50 +0.10 -0.00 D1 1.50 min. Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-15 QFN 4x4x0.9 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko Ao B φD1 A B T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko T SPEC. 4.40±0.20 4.40±0.20 1.20±0.20 0.30±0.05 SYMBOL Po P1 P2 E1 F W SPEC. 4.00±0.10 8.00±0.10 2.00±0.05 1.75±0.10 5.50±0.05 12.00±0.30 Do 1.50 +0.10 -0.00 D1 1.50 min. Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-16 DFN 2x2x0.75 CARRIER TAPE OUTLINE DRAWING Po P2 P1 W Bo F E1 φDo Ko Ao φD1 T SECTION A-A SECTION B-B φDo φD1 SYMBOL Ao Bo Ko T SPEC. 2.30±0.10 2.30±0.10 1.15±0.10 0.26±0.04 SYMBOL Po P1 P2 E1 F W SPEC. 4.00±0.10 4.00±0.10 2.00±0.05 1.75±0.10 3.50±0.05 8.00±0.30 1.50 +0.10 1.00 +0.25 -0.00 -0.00 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-17 DFN 3x3x0.75 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko B Ao φD1 A B T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko T SPEC. 3.30±0.20 3.30±0.20 1.15±0.25 0.30±0.05 SYMBOL Po P1 P2 E1 F W SPEC. 4.00±0.10 8.00±0.10 2.00±0.10 1.75±0.10 5.50±0.10 12.00±0.30 Do 1.50 +0.10 -0.00 D1 1.50 min. Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-18 SC-70/SC-82 CARRIER TAPE OUTLINE DRAWING Po P2 P1 W Bo F E1 φDo Ko Ao φD1 T SECTION A-A SECTION B-B SYMBOL Ao Bo Ko SPEC. 2.25 ±0.10 2.40 ±0.10 1.22 ±0.10 SYMBOL Po P1 P2 E1 SPEC. 4.00 ±0.10 4.00 ±0.10 2.00 ±0.05 1.75 ±0.10 T 0.254 ± 0.02 φDo 1.50 φD1 +0.10 1.00 +0.25 -0.00 -0.00 F 3.50 ±0.05 8.00 W +0.30 -0.10 Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-19 TSSOP-16 CARRIER TAPE OUTLINE DRAWING Po P2 P1 A Bo W F E1 φDo Ko Ao B φD1 A B T SECTION A-A SECTION B-B Do SYMBOL Ao Bo Ko T SPEC. 6.80±0.20 5.40±0.20 1.60±0.20 0.30±0.05 SYMBOL Po P1 P2 E1 F W SPEC. 4.00±0.10 8.00±0.10 2.00±0.05 1.75±0.10 5.50±0.05 12.00±0.30 1.50 +0.10 -0.00 D1 1.50 min. Note: 1. Refer to EIA-481-B 2. 10 sprocket hole pitch cumulative tolerance ± 0.2 3. Material: conductive polystyrene 4. Ao and Bo measured on a plane 0.3mm above the bottom of the pocket 5. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier II-20 Part III Reel Outline Drawing (unit：mm) REEL OUTLINE DRAWING Package Type H W C d D 330±2 60 MIN. +2.0 24.4 -0.0 +0.5 13.0 -0.2 1.5 MIN. 20.2 MIN. TO-252-3L TO-252-5L SOP-14(150mil) SOP-16(150mil) SOP-16W (300mil) 330±2 50 MIN. 16.4 +2.0 -0.0 13.0 +0.5 -0.2 1.5 MIN. 20.2 MIN. SOP-8 TSSOP-16 MSOP-8 MSOP-10 SOT-223 QFN 3x3 QFN 4x4 DFN 3x3 330±2 50 MIN. 12.4 +2.0 -0.0 13.0 +0.5 -0.2 1.5 MIN. 20.2 MIN. 178±2 50 MIN. 12.4 +2.0 -0.0 13.0 +0.5 -0.2 1.5 MIN. 20.2 MIN. 178±2 50 MIN. 8.4 +2.0 -0.0 13.0 +0.5 -0.2 1.5 MIN. 20.2 MIN. TO-263-3L A H TO-263-5L SOT-89-3L d W SOT-89-5L SOT-143 SOT-23-x TSOT-23-x SC-70 SC-82 DFN 2x2 A Note: Refer to EIA-481-B φC D TO-92 TAPING SPEC. DRAWING A W B E F P1 P e φD T SYMBOL W A B E F 1 9 .0 ± 0 .5 SPEC. 1 8 .0 ± 0 .2 9 .0 ± 0 .2 6 .0 ± 0 .2 0 1 6 .0 ± 0 .5 SYMBOL P P1 D e T SPEC. 1 2 .7 B S C 1 2 .7 B S C 4 .0 ± 0 .2 2 .5 B S C 0 .6 ± 0 .1 III-1